REPAIR AND MAINTANANCE OF WATER SUPPLY PUMP SETS AND CONNECTED ACCESSORIES AT VAYUSENA NAGAR NAGPUR

Amount

Material and labour for opening of pump set split case centrifugal type 35 LPS, 75 mtr head coupled to electric motor of capacity 50 HP/60HP of make Kirloskar / Crompton from motor coupling after isolating the electric and earth lead connections opening the pump set for repair/overhauling etc including replacing the items with new items given vide item No 2 below, reassemblying the pumpset greasing connecting, testing and commissioning complete including necessary lathe works and alingment of pump impeller with motor shaft all as specified and directed.

Supply only spare parts for pump set for fixing against item No.1 as follows:-

(a) Pump shaft

(b) Bearings as per existing with bearing sleeve for DE for pump (6307)

(c) Bearings as per existing with bearing sleeve for NDE for pump (3307)

(d) Oil/ water seal / mechanical seal assembly

(e) Impeller stainless steel as per casing dia

(f) Supply only air relase valve for pump

(g) Impeller lock nut

(h) Terminal box cover

(j) Gland rope Upto 2 Mtr

(k) Coupling with rubber bush as per existing type SW

(l) Pump Gasket

(m) Shaft sleeve bronze

(n) Pump wear ring and Pump shoulder ring

(o) Bearings as per existing with bearing sleeve for drive end/ non drive end for motor (6313)

(p) Cooling fan for motor

(q) O Ring

Make of bearing : SKF/TIMKER/NSK/URB Note:- (a) All the items/parts mentioned against 2(a) to 2(q) here-in-before shall be suitable/compatible for the type and make of pumping set as mentioned against item No 1 above. (b) Labour cost of fixing of items is deemed to be included in the quoted rate of item No 01 above (c) The quoted rate of item No 1 shall deemed to be included rate for alignment of pump carried out by highly skilled machanic.

Material and labour for preparation of old painted exposed surface of centrifugal pump set of capacity 60HP with suction line from UG sump to Pump set & delivery pipe line & oulet pipe line from pump set to wall/ pit as observed inside plant room , operating valves (Non return valve/ sluice valve/ Gate Valve ) any size by removing dust, dirt, oil, grease etc & and painting with two coats of synthetic enamel paint of superior quality as per existing colour or as approved colour using spray gun and writing SM No / MES No to pump sets with white paint complete all as specified and directed. Make : Asian paint/Berger/Nerolac

All as per item No 3 here in before but centrifugal pump set of capacity 50HP.

All as per Item No 1 here in before but the capacity of the pump set 25 HP to 40 HP at pump house all as specified and directed.

Supply only spare parts for pump set vide item no. 5 above

(a) Supply only pump shaft sleeve made out of gun metal

(b) Supply only key for main shaft/impeller

(c) Supply only check nut for pump set shaft

(d) Supply only stuffing box bush

(e) Supply only water seal

(f) Supply only rubber tyre coupling complete Make :- Fenner/ Unique/ Unimac

(g) Supply only Motor set bearing housing DE 6310 / NDE 6309

(h) Supply only Pump set bearing housing DE 6307/ NDE 6307

(j) Supply only Air relase valve for pump

(k) Supply only pump Shaft

(l) Cooling fan for motor

(m) Terminal plate

(n) Terminal box

Make of bearing : SKF/TIMKER/NSK/URB

Note: (i)All the items/parts mentioned against 6(a) to 6(n) here-in-before shall be suitable/compatible for the type and make of pumping set as mentioned against item No 5 above. (b) Labour cost of fixing of items is deemed to be included in the quoted rate of item No 05 above (c) The quoted rate of item No 5 shall deemed to be included rate for alignment of pump carried out by highly skilled machanic.

Material and labour for preparation of old painted exposed surface of Centrifugal pump set of capacity 25HP upto 40 HP , with suction line from UG sump to Pump set & delivery pipe line & oulet pipe line from pump set to wall/pit as observed inside plant room , operating valves(Non return valve/Sluice valve/Gate Valve ) any size by removing dust, dirt, oil, grease etc & and painting with two coats of synthetic enamel paint of superior quality as per dark blue for pump set and pipe line outlet/Inlet for light blue existing colour or as approved colour using spray gun and writing SM/ MES No to pump sets with white paint complete all as specified and directed. Make :Asian paint/Berger/Nerolac

All as per item No 7 here in before but centrifugal pump set of capacity 15HP.

All as per Item No 1 here in before but the capacity of the pump set 20 HP at pump house.

Supply only spare parts for pump set vide item no. 9 above

(a) Supply only pump shaft sleeve made out of gun metal

(b) Supply only key for main shaft/impeller

(c) Supply only check nut for pump set shaft

(d) Supply only stuffing box bush

(e) Supply only water seal

(f) Supply only rubber tyre coupling complete Make :- Fenner/Unique/Unimac

(g) Supply only pump set bearing housing DE 6307 / NDE 6307

(h) Supply only Motor set bearing housing DE 6310 / NDE 6309

(j) Supply only Air relase valve

(k) Supply only pump Shaft

(l) Cooling fan for motor

(m) Terminal plate

(n) Terminal box

(o) Oil/water seal /Mechanical seal assembly

(p) O ring

(q) Impeller lock nut

(r) Gland rope Upto 2 Mtr

(s) Coupling with rubber bush as per existing

(t) Pump Gasket

(u) Shaft sleeve

(v) Pump wear ring and Pump shoulder ring

(w) Key for coupling

(x) Gland Plate

Material and labour for preparation of old painted exposed surface of centrifugal pump set of capacity 20HP, with suction line from UG sump to Pump set & delivery pipe line & oulet pipe line from pump set to wall/pit as observed inside plant room , operating valves(Non return valve/Sluice valve/Gate Valve ) any size by removing dust, dirt, oil, grease etc & and painting with two coats of synthetic enamel paint of superior quality as per Dark blue for pump set and pipe line outlet/Inlet for light blue existing colour or as approved colour using spray gun and writing SM/ MES No to pump sets with white paint complete all as specified and directed. Make : Asian paint/Berger/Nerolac

Material and labour for cement concrete type 1:3:6 (40 mm graded aggregate ) thickness of cement concrete is not less than 100 mm thick including finishing surface even and smooth for making floors for new pump house at Telenkheri.

Material and labour for repairing / servicing of unserviceable centrifugal pump set of suitable capacity coupled with 15HP electric motor by dismantling the pump and taking out defective / unsv / worn out parts of pump set and replacement of all defective parts as under and reassebling the pump set including proper alignment and testing complete all as specified and directed.

All as per Item No 1here in before but the capacity of the pump set 15 HP at pump house. Make- Kirloskar

Supply only spare parts for pump set vide item no. 14 above

(a) Supply only pump shaft sleeve made out of gun metal

(b) Supply only key for main shaft/impeller

(c) Supply only check nut for pump set shaft

(d) Supply only stuffing box bush

(e) Supply only water seal

(f) Supply only rubber tyre coupling complete make :- Fenner/Unique/Unimac

(g) Supply only pump set bearing housing DE 6307 / NDE 6307

(h) Supply only Motor set bearing housing DE 6310 / NDE 6309

(j) Supply only Air relase valve

(k) Supply only pump Shaft

(l) Cooling fan for motor

(m) Terminal plate

(n) Terminal box

(o) oil/water seal /Mechanical seal assembly

(p) O ring

(q) Impeller lock nut

(r) Gland rope Upto 2 Mtr

(s) Coupling with rubber bush as per existing

(t) Shaft sleeve

(u) Pump wear ring and Pump shoulder ring

(v) Key for coupling

(w) Gland Plate

Make of bearing : SKF/TIMKER/NSK/URB

Note: (a) All the items/ parts mentioned against 15(a) to 15(w) here-in-before shall be suitable/compatible for the type and make of pumping set as mentioned against item No 14 above. (b) Labour cost of fixing of items is deemed to be included in the quoted rate of item No 14above (c) The quoted rate of item No 14 shall deemed to be included rate for alignment of pump carried out by highly skilled machanic.

Taking down electric motor 60 HP/50 HP 415 volt coupled to centrifugal pump after disconnecting the electrical connection, and earth connections from its foundation and transportation to work shop opening carefully the rotor and stator winding and cleaning and removing all dust and dirt carefully , varnishing the stator to enhance the insulation level, baking, drying complete, greasing on reassemblying the motor to back to pump house / installation and reinstallation on foundation, reconnecting, cable connection fixed new thumble and pump/shifts alignment and reconnect earth connections etc complete in all respect and starting the pump ,testing complete all as specified and directed. Note : Cost of re-winding & bearings shall be measured and paid separately.

All as per Item No 16 here in before but the capacity of motor 25 HP Note- Cost of Rewinding Bearings shall be measured and paid separetely.

All as per Item No 16 here in before but the capacity of motor 7.5 HP Note : Cost of re-winding & bearings shall be measured and paid separately.

Material and labour for preparation of old painted exposed surface of centrifugal pump set of capacity 7.5HP, with suction line from UG sump to Pump set & delivery pipe line & oulet pipe line from pump set to wall/pit as observed inside plant room , operating valves(Non return valve/Sluice valve/Gate Valve ) any size by removing dust, dirt, oil, grease etc & and painting with two coats of synthetic enamel paint of superior quality as per dark blue for pump set and pipe line outlet/Inlet for light blue existing colour or as approved colour using spray gun and writing SM/ MES No to pump sets with white paint complete all as specified and directed. Make : Asian paint/Berger/Nerolac

All as per Item No 16 here in before but the capacity of motor 5 to 10 HP Note- Cost of Rewinding Bearings shall be measured and paid separetely.

Taking down electric motor from centrifugal monoblock pump 15 HP 415 volt coupled to pump after disconnecting the electrical connection, and earth connections from open well/ sump and transportation to work shop) opening carefully the rotor and stator winding and cleaning and removing all dust and dirt carefully ,warnishing the stator to enhance the insulation level, baking, drying complete, greasing on reassemblying the motor and reinstallation on foundation, reconnecting back the cable and earth connections etc and testing complete in all respect all as directed.

Dismantling monoblock pump set type 15 LPS, 44 mtr head 7.5 Hp to 10 HP 415 Volt, from foundation base plate after isolating the electric and earth lead connections, suction and delivery pipes etc loading, shifting pump set to workshop opening the pump set, motor rotor and stator etc for repair/overhauling and warnishing and baking the stator winding to enhance the insulation level including replacing unserviceable items with new items given vide item No 23 below and tranportation to the pump house reassmblying the Moter with pumpset reinstalling on foundation frame connecting, testing and commissioning complete all as specified.

Supply only spare parts for pump set vide item No 22 as follows:-

(a) Supply only pump shaft sleeve made out of gun metal

(b) Supply only key for main shaft/impeller

(c) Supply only check nut

(d) Supply only stuffing box bush

(e) Supply only water seal

(f) Supply only stuffing box packing and greasing

(g) Supply only ball bearing complete DE/NDE. make NBC/TATA/SKF

Make of bearing : SKF/TIMKER/NSK/URB

Note: (a) All the items/parts mentioned against 23(a) to 23(g) here-in-before shall be suitable/compatible for the type and make of pumping set as mentioned against item 22. (b) Labour cost of fixing of items is deemed to be included in the quoted rate of item No 22 above (c) The quoted rate of item No 22 shall deemed to be included rate for alignment of pump carried out by highly skilled machanic.

Material and labour for preparation of old painted exposed surface of Centrifugal pump set of capacity 5 HP to 10HP with suction line from UG sump to Pump set & delivery pipe line & oulet pipe line from pump set to wall/pit as observed inside plant room , operating valves(Non return valve/Sluice valve/Gate Valve ) any size by removing dust, dirt, oil, grease etc & and painting with two coats of synthetic enamel paint of superior quality as per Dark blue for pump set and pipe line outlet/Inlet for light blue existing colour or as approved colour using spray gun and writing SM/ MES No to pump sets with white paint complete all as specified and directed. Make :Asian paint/Berger/Nerolac

Dismantling monoblock pump set type 15 LPS, 44 mtr head 12.5 HP 415 Volt, from foundation base plate after isolating the electric and earth lead connections, suction and delivery pipes etc loading, shifting pump set to workshop opening the pump set, motor rotor and stator etc for repair/overhauling and warnishing and baking the stator winding to enhance the insulation level including replacing unserviceable items with new items given vide item No 26 below and tranportation to the pump house reassmblying the Moter with pumpset reinstalling on foundation frame connecting, testing and commissioning complete all as specified and directed.

Supply only spare parts for pump set vide item No 25 as follows:-

(a) Supply only pump shaft sleeve made out of gun metal

(b) Supply only key for main shaft/impeller

(c) Supply only check nut

(d) Supply only stuffing box bush

(e) Supply only water seal

(f) Supply only stuffing box packing and greasing

(g) Supply only ball bearing complete DE/NDE. make NBC/TATA/SKF

(h) Supply only pump Shaft

(j) Supply ball/r bearing motor as per existingcomplete

Make of bearing : SKF/TIMKER/NSK/URB

Note: (a) All the items/parts mentioned against 26(a) to 26(j) here-in-before shall be suitable/compatible for the type and make of pumping set as mentioned against item 25. (b) Labour cost of fixing of items is deemed to be included in the quoted rate of item No 25 above. (c) The quoted rate of item No 25 shall deemed to be included rate for alignment of pump carried out by highly skilled machanic.

Dismantling monoblock pump set centrifugal type 1 HP to 5 HP 415 Volt,Kirloskar make from foundation base plate after isolating the electric and earth lead connections, suction and delivery pipes etc loading, shifting pump set to workshop opening the pump set, motor rotor and stator etc for repair/overhauling and warnishing and baking the stator winding to enhance the insulation level including replacing the unserviceable parts with new items given vide item 28 below and reassmblying the pumpset and transporting back to site reinstalling on foundation frame connecting, testing and commissioning complete all as specified.

Supply only spare parts for 1 to 5HP pump set for replacing old unserviceable item in pump set dismantling vide item No.27 as above:-

(a) Supply only pump shaft sleeve made out of gun metal

(b) Supply only key for main shaft

(c) Supply only check nut

(d) Supply only water seal

(e) Supply only pump Shaft machine charges

(f) Supply only ball bearing complete DE/NDE. Make NBC/TATA/SKF

Note: (a) All the items/parts mentioned against 28(a) to 28(f) shall be suitable/compatible for the type and make of pumping set as mentioned against item No. 27 (b) Labour cost of fixing of items is deemed to be included in the quoted rate of item No 27 above. (c) The quoted rate of item No 27 shall deemed to be included rate for alignment of pump carried out by highly skilled machanic.

Dismantling Submersible pump set/ centrifugal type 1 HP to 5 HP 3 phase 415 V from foundation base plate after isolating the electric and earth lead connections, suction and delivery pipes etc opening the pump set, motor rotor and stator etc for repair/overhauling and warnishing and baking the stator winding to enhance the insulation level including replacing the unserviceable parts with new items given vide item No below and reassemblying the pumpset and reinstalling on foundation frame connecting, testing and commissioning complete all as specified and directed.

Supply only spare parts for Submersiable pump set of capacity 1 to 5 HP vide item No.29 above as follows:-

(a) Supply only gun metal bush

(b) Supply only Impeller check nut

(c) Supply only cast iron impeller

(d) Supply only water seal

(e) Thrust Plate

(f) Thrust bearing

(g) Machining charges

(h) Nutbolt as per requiement

(j) Cable flat 3 cor 2.5 sqmmNutbolt as per requiement

Note : (a) All the items/parts mentioned against 30(a) to 30(j) to here-in-before shall be suitable/compatible for the type and make of pumping set as mentioned against item Cost of fixing of items is deemed to bne included in the unit rate of item 29. (b) Labour cost of fixing of items is deemed to be included in the quoted rate of item No 29 above. (c) The quoted rate of item No 29 shall deemed to be included rate for alignment of pump carried out by highly skilled machanic.

Dismantling Submersible pump set Open well 7.5 HP 3 phase 415 V from UG sump/open well after isolating the electric and earth lead connections, suction and delivery pipes etc opening the pump set, motor rotor and stator etc for repair/overhauling and warnishing and baking the stator winding to enhance the insulation level including replacing the unserviceable parts with new items given vide item No given below and reassemblying the pumpset and reinstalling on foundation frame connecting, testing and commissioning complete all as specified and directed.

Supply only spare parts for submersiable pump set openwell of capacity 7.5 HP vide item No. 31 above as follows:-

(a) Supply only gun metal bush Motor

(b) Supply only Impeller check nut

(c) Supply only cast iron impeller

(d) Supply only water seal

(e) Thrust Plate

(f) Thrust bearing

(g) Machining charges

(h) Nutbolt as per requiement

(j) Cable flat 3 cor 4 sqmm Nutbolt as per requiement

Note : (a) All the items/parts mentioned against 32(a) to 32(j) to here-in-before shall be suitable/compatible for the type and make of pumping set as mentioned against item Cost of fixing of items is deemed to bne included in the unit rate of item 31. (b) Labour cost of fixing of items is deemed to be included in the quoted rate of item No 31above. (c) The quoted rate of item No 31 shall deemed to be included rate for alignment of pump carried out by highly skilled machanic.

Dismantling vertical Submersible borewell pump set 7.5 HP 3 phase 415 V from existing borewell lifting and lowering after isolating the electric and earth lead connections, delivery pipes etc opening the borewell pump set, and motor pump etc for repair/overhauling connecting, testing and commissioning complete all as specified. ncluding replacing the unserviceable parts with new items given vide item No given below and reassemblying the borewell pumpset and reinstalling onlower connecting, testing and commissioning complete all as specified and directed.

Supply only spare parts for pump set of capacity 7.5 HP vide item No. 33 as follows:-

(a) Supply onlygun metal bush for motor

(b) Supply only Thrust plate

(c) Supply only Thrust bearing

(d) Supply only water seal

(e) Supply only Motor cabel 4 sqmm flat cabel 3 core

(f) Pump coupler

(g) Pump bush

(h) Pump Impeller

(j) Pump diffuser

Note : (a) All the items/parts mentioned against 34(a) to 34(j) to here-in-before shall be suitable/compatible for the type and make of pumping set as mentioned against item Cost of fixing of items is deemed to bne included in the unit rate of item 33. (b) Labour cost of fixing of items is deemed to be included in the quoted rate of item No 33 above. (c) The quoted rate of item No 33 shall deemed to be included rate for alignment of pump carried out by highly skilled machanic.

Dismantling Open well Submersible pump set 03 to 15 HP, 3 phase 415 V from UG sump/open well after isolating the electric and earth lead connections, suction and delivery pipes etc opening the pump set, motor rotor and stator etc for repair/overhauling and warnishing and baking the stator winding to enhance the insulation level including replacing the unserviceable parts with new items given vide item No given below and reassemblying the pumpset and reinstalling on foundation frame connecting, testing and commissioning complete all as specified and directed.

Supply only spare parts for pump set of capacity 15 HP vide item No. 35 above as follows:-

(a) Supply only pump shaft sleeve made out of gun metal

(b) Supply only key for main shaft

(c) Supply only check nut

(d) Supply only cast iron impeller

(e) Supply only water seal

(f) Supply only stuffing box packing and greasing

(g) Supply only ball bearing complete Make- NBC/TATA/SKF

Note : (a) All the items/parts mentioned against 36(a) to 36(g) to here-in-before shall be suitable/compatible for the type and make of pumping set as mentioned against item Cost of fixing of items is deemed to bne included in the unit rate of item 35. (b) Labour cost of fixing of items is deemed to be included in the quoted rate of item No 35 above. (c) The quoted rate of item No 35 shall deemed to be included rate for alignment of pump carried out by highly skilled machanic.

Dismantling booster pump 0.5 to 1 HP 3/1 phase 415/250 V from foundation base plate after isolating the electric and earth lead connections, suction and delivery pipes etc opening the pump set, motor rotor and stator etc for repair/overhauling and warnishing and baking the stator winding to enhance the insulation level including replacing the unserviceable parts with new items given vide item No given below and reassemblying the pumpset and reinstalling on foundation frame connecting, testing and commissioning complete all as specified and directed.

Supply only spare parts for pump set of capacity 0.5 to 1 HP vide item No. 37 as follows:-

(a) Pressure tank suitbale for 1 hp 24 ltr capacity

(b) Pressure switch suitable for 1 hp

(c) Float switch

(d) Y Type strainer

(e) Pressure gauge

(f) SS flexible pipe

(g) NRV 25 mm

(h) 5 way connector

(j) Hex nipple

(k) Impeller

Note: (a) All the items/parts mentioned against 38 (a) to 38 (k) to here-in-before shall be suitable/compatible for the type and make of pumping set as mentioned against item Cost of fixing of items is deemed to bne included in the unit rate of item 38 (b) Labour cost of fixing of items is deemed to be included in the quoted rate of item No 38 above. (c) The quoted rate of item No 38 shall deemed to be included rate for alignment of pump carried out by highly skilled machanic.

Material and labour for rewinding of pump motor 415 Volt 3 phase after disconnecting electric cable and eath lead, suction and delivery pipes, shifting to work shop, dismantling the motor assembly and removing the burnt out copper winding of stator and cleaning the stator slots and core assembly, rewinding to stator with suitable gauge super enamelled copper wire with insulating papers and insulation cloths, varnishing the winding and baking heating for achieving the required insulation resistance, re-assembling the motor and testing complete, incl transporting back to site and fixing motor to its original place, reconnecting electric cable and earth leads etc testing and commissioning complete in all respect all as specified and directed.

(a) up to 7.5 hp

Note : Cost of Bearings shall be measured and paid separately under relevent item.

Material and labour for Rewinding of submersible pump set/open well submersible pump set 415 Volt 3 phase after disconnecting electric cable and eath lead, suction and delivery pipes, shifting to work shop, dismantling the motor assembly and removing the burnt out copper winding of stator and cleaning the stator slots and core assembly, rewinding to stator with suitable gauge super enamelled copper wire with insulating papers and insulation cloths, varnishing the winding and baking heating for achieving the required insulation resistance, re-assembling the motor and testing complete, incl transporting back to site and fixing motor to its original place, reconnecting electric cable and earth leads etc testing and commissioning complete in all respect all as specified and directed.

(a) 1 to 3 HP

Taking out existing starter pannel from concrete foundation by disconnecting main cable and all outgoing cable fixing the same panel and making all connections inside pump house. Note- PCC 1:2:4 will be measured and paid under relevent item.

Supply and laying LT Rubber mating chequered type of size 2 mtr x 1 mtr x 2.5 mm thick as per IS 5424/1969 complete all as specified and directed.

Supply and fixing in repair cast iron foot valve confirming to IS:4038 with rubber seating, flanged end complete incl taking out old unsvall as specified and as directed. Make: Kirloskar/ Leader /Venus

(a) 100 mm bore

(b) 150 mm bore

(c) 80 mm bore

Supply and fix in repair high pressure, heavy duty cast iron non return sluice valve/ check valve of following sizes, conforming to BS 1868, Class PN 1.6, suitable to hydrostatic test pressure for body 156 kg/sq cm & for seat 115 kg/sq cm, both ends flanged in existing line, after removal of old unserviceable non return valve without damaging to existing pipe line complete all as specified and directed. Make Kirloskar Leader /Venus/ Note : The quoted rate shall deemed to be included rate for suitable size MS flanges for existing pipe line, Joints and jointing materials.

(a) 150mm dia

(b) 100mm dia

(c) 80mm dia

(d) 50mm dia

Supply & fix in repair of cast iron Sluice valve PN1.6 as per IS-14846, body, dome, wedge-CI IS:210, rings-bronze IS:318, Spindal-SS IS:6603, Gland Packing greasy jute packing, fasteners-CS, Gasket- Natural rubber, nominal size as under, both ends flanged in existing line, after removal of old unserviceable sluice valve without damaging to existing pipe line complete all as specified and directed by Engr-in-charge. Make: Kirloskar Leader /Venus/ Note : The quoted rate shall deemed to be included rate for suitable size MS flanges for existing pipe line, Joints and jointing materials.

(a)150mm dia

(b)100mm dia

(c) 80mm dia

(d) 50mm dia

Supply and fixing Gun metal gate valve class-1 for 15mm bore pipe, with iron wheel head, screwed both ends for iron pipe and fixed, ISI marked conforming to IS 778: 1984, fixed as in repair complete all as specified and directed. Make : SANT/ZOLOTO/LEADER

All as per serial item No.46 here-in-before but of size 20mm bore.

Material and labour for repair pump set cover of open Pump set upto monoblock pump set 5 to 15 HP ISI Mark all as specified and directed.

Supply and fixing in repair stainless steel bourdon type pressure gauge dial type 0 -25 Kg/cm2 range with a stainless steel body complete including all necessary GI pipe connection fittings / cutting / jointing// boring of existing pipe all as specified and directed. Make: Guru/Feibeg/omega

Material and labour for framed work such as grills, gratings etc with ends of bar shouldered and or riveted or forged into spikes framed guarded bars barred iron doors ladders framed balusters walkways railings framed work of water tank stand similar work confirming Gde-E-165 complete all as specified and directed.

Taking out motor and pumpset with base channel by disconnecting motor electric connections and pumpset 25 HP from coupling and disconnecting existing inlet and outlet pipeline and keep a safe custody for refixing after raising height of PCC platform/ base all as specified and directed.

Material and labour for PCC 1 : 2 : 4 (40 mm graded aggregate ) for raising of platform of motor pump , making pocket for fixing holdfast for pump base plate / channel including necessary shuttering all as specified and directed.

Material and labour for plastering with 1 : 4 to PCC platform all as specified and directed.

Supply and fix holdfast with thread and washer, nuts of any dia and length as required at site for fixing motor complete all as specified and directed.

Fixing only motor and pump set 25 HP (dismantled vide item No 51) on raised concrete platform and connecting inlet and outlet pipline and testing complete all as specified and directed.

Taking out existing inlet and outlet pipe GI 80 - 100 mm (approximately 15 metre) along with foot valve, NRV, Sluice valve and making alternation to match the piping with pumpset fixed on raised platform and reflexing the same by making necessary alternations all as specified and directed. Note - The quoted rate shall deemed to be included rate for neccessary fittings like bends , union, sockets pipe up to 2 metre.

Supply and fix 16 sq mm single core copper flexible wire from motor to existing panel with necessary copper lugs including HDPE pipe with suitable size for cable all as specified and directed. Make :- Havells/Finolex/Polycab

chronicle enterprises

Paragon Electrotechnics