Construction of (G Plus 1) storied Duplex type Residential Quarter M-20, M-21 and M-22 at Minister Colony, Dispur, Ghy-06

Amount

Providing, driving with hydraulic piling rigs with power units and installing driven cast-in-situ reinforced cement concrete piles of grade M-25 of specified diameter and length below the pile cap, to carry safe working load not less than specified, excluding the cost of steel reinforcement but including the cost of shoe and the length of pile to be embedded in the pile cap etc. all complete. (Length of pile for payment shall be measured from top of shoe to the bottom of pile cap) : 400 mm dia piles

Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete above plinth level.5.22A.6 Thermo-Mechanically Treated bars of grade Fe-500D or more.

Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement - All work up to plinth level :1:1.5:3 (1 cement : 1.5 coarse sand (zone-III) derived from natural sources : 3 graded stone aggregate 20 mm nominal size de rived from natural sources)

Earth work in rough excavation, banking excavated earth in layers not exceeding 20cm in depth, breaking clods, watering, rolling each layer with ½ tonne roller or wooden or steel rammers, and rolling every 3rd and top-most layer with power roller of minimum 8 tonnes and dressing up in embankments for roads, flood banks, marginal banks and guide banks or filling up ground depressions, lead upto 50 m and lift upto 1.5 m : All kinds of soil

Close timbering in trenches including strutting, shoring and packing cavities (wherever required) complete. (Measurements to be taken of the face area timbered). Depth not exceeding 1.5 m

Demolishing R.C.C. work manually/ by mechanical means including stacking of steel bars and disposal of unserviceable material within 50 metres lead as per direction of Engineer - in- charge.

Dry brick pitching half brick thick in drains including supply of bricks and preparing the surface complete : 16.12.1 With common burnt clay F.P.S. (non modular) bricks of class designation 7.5

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level :½:3 (1 Cement: 1½ coarse sand (zone-III) derived from natural sources : 3 graded stone aggregate 20 mm nominal size derived from natural sources)

Centering and shuttering including strutting, propping etc. and removal of form for Foundations, footings, bases of columns, etc. for mass concrete

Centering and shuttering including strutting, propping etc. and removal of form forColumns, Pillars, Piers, Abutments, Posts and Struts

Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in foundation and plinth in: Cement mortar 1:4 (1 cement : 4 coarse sand)

Supplying and filling in plinth with sand under floors, including watering, ramming, consolidating and dressing complete.

Diluting and injecting chemical emulsion for POST-CONSTRUCTIONAL anti-termite treatment (excluding the cost of chemical emulsion) :Treatment of soil under existing floors using chemical emulsion @ one litre per hole, 300 mm apart including drilling 12 mm diameter holes and plugging with cement mortar 1 :2 (1 cement : 2 Coarse sand) to match the existing floor: With Chlorpyriphos/Lindane E.C. 20% with 1% concentration

Suspended floors, roofs, landings, balconies and access platform

Lintels, beams, plinth beams, girders, bressumers and cantilevers

Reinforced cement concrete work in beams, suspended floors, roofs having slope up to 15° landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases above plinth level up to floor five level, excluding the cost of centering, shuttering, finishing and reinforcement with 1:1.5:3 (1 cement : 1.5 coarse sand(zone-III) derived from natural sources : 3 graded stone aggregate 20 mm nominal size derived from natural sources).

Providing and laying damp-proof course 40mm thick with cement concrete 1:2:4 (1 cement : 2 coarse sand (zone-III) derived from natural sources : 4 graded stone aggregate 12.5mm nominal size derived from natural sources)

Half brick masonry with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level.6. Cement mortar 1:3 (1 cement :3 coarse sand)

Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position with hold fast lugs or with dash fasteners of required dia & length (hold fast lugs or dash fastener shall be paid for separately). Sal wood

CEMENT PLASTER (IN COARSE SAND)15 mm cement plaster on the rough side of single or half brick wall of mix : 1:4 (1 cement: 4 coarse sand)

Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete.

Applying priming coats with primer of approved brand and manufacture, having low VOC (Volatile Organic Compound ) content.With ready mixed pink or grey primer on wood work (hard and soft wood) having VOC content less than 50 grams/ litre

Wall painting with premium acrylic emulsion paint of interior grade, having VOC (Volatile Organic Compound ) content less than 50 grams/ litre of approved brand and manufacture, including applying additional coats wherever required to achieve even shade and colour Two coats

Finishing walls with Acrylic Smooth exterior paint of required shade New work (Two or more coat applied @ 1.67 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm)

Providing and fixing factory made uPVC white colour casement/case mentcum fixed glazed windows comprising of uPVC multi-chambered frame, sash and mullion (where ever required) extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), uPVC extruded glazing beads of appropriate dimension, EPDM gasket, stainless steel (SS 304 grade) friction hinges, zinc alloy (white powder coated) casement handles, G.I fasteners 100 x 8 mm size for fixing frame to finished wall, plastic packers, plastic caps and necessary stainless steel screws etc. Profile of frame & sash shall be mitred cut and fusion welded at all corners, mullion (if required) shall be also fusion welded including drilling of holes for fixing hardware's and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealant over backer rod of required size and of approved quality, all complete as per approved drawing & direction of Engineer-in-Charge. (Single / double glass panes and silicon sealant shall be paid separately). Variation in profile dimension in higher side shall be accepted but no extra payment on this account shall be made. Note: For uPVC frame, sash and mullion extruded profiles minus 5% tolerancein dimension i.e. in depth & width of profile shall be acceptable. 9.147A.1 Casement window single panel with S.S. friction hinges (300 x 19 x 1.9 mm), made of (small series) frame 47 x 50 mm & sash 47 x 68 mm both having wall thickness of 1.9 ± 0.2 mm and single glass pane glazing bead of appropriate dimension. (Area of window upto 0.75 sqm.)

Providing and fixing factory made uPVC white colour casement/ Casement cum fixed glazed door comprising of uPVC multi-chambered frame, sash and mullion (where ever required) extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), uPVC extruded glazing beads of appropriate dimension, EPDM gasket, zinc alloy (white powder coated) 3D hinges and one handle on each side of panels along with zinc plated mild steel multi point locking SUB HEAD : 9.0 WOOD AND P.V.C. WORK 210 Code Description Unit Rate No. having transmission gear, cylinder with keeps and one side key, G.I fasteners 100 x 8 mm size for fixing frame to finished wall and necessary stainless steel screws, etc. Profile of frame & sash shall be mitred cut and fusion welded at all corners, mullion (if required) shall be also fusion welded including drilling of holes for fixing hardware's and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealent over backer rod of required size and of approved quality, all complete as per approved drawing & direction of Engineer-in-Charge. (Single / double glass panes and silicon sealent shall be paid separately). Variation in profile dimension in higher side shall be accepted but no extra payment on this account shall be made. Note: For uPVC frame, sash and mullion extruded profiles minus 5% tolerance in dimension i.e. in depth & width of profile shall be acceptable. 9.147C.1 Casement door with 3D hinges made of (big series) frame 67 x 64 mm & sash 67 x 110 mm both having wall thickness of 2.3 ± 0.2 mm and single glazing bead / double glazing bead of appropriate dimension. (Area of door upto 2.00 sqm).

Providing and fixing panelled or panelled and glazed shutters for doors, windows and clerestory windows, fixing with butt hinges of required size with necessary screws, excluding panelling which will be paid for separately, all complete as per direction of Engineer-in-charge. (Note:- Butt hinges and necessary screws shall be paid separately) Second class teak wood 35 mm thick shutters

Providing and fixing ISI marked flush door shutters conforming to IS :2202 (Part I) decorative type, core of block board construction with frame of 1st class hard wood and well matched teak 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters. 35 mm thick including ISI marked Stainless Steel butt hinges with necessary screws

Providing and fixing M.S. grills of required pattern in frames of windows etc. with M.S. flats, square or round bars etc. including priming coat with approved steel primer all complete.9.48.1 Fixed to steel windows by welding

Providing and fixing aluminium die cast body tubular type universal hydraulic door closer (having brand logo with ISI, IS : 3564, embossed on the body, door weight upto 35 kg and door width upto 700 mm), with necessary accessories and screws etc. complete.

Providing and fixing chromium plated brass 100 mm mortice latch and lock with 6 levers and a pair of lever handles of approved quality with necessary screws etc. complete.

Providing and fixing chromium plated brass handles with necessary screws etc. complete: 125 mm

Providing and fixing ISI marked aluminium butt hinges anodised (anodiccoating not less than grade AC 10 as per IS: 1868) transparent or dyed to required colour or shade with necessary screws etc. complete: 125x75x4 mm

Providing and fixing aluminium sliding door bolts, ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868), transparent or dyed to required colour or shade, with nuts and screws etc. complete :300x16 mm

Providing and fixing aluminium tower bolts, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868 ) transparent or dyed to required colour or shade, with necessary screws etc. complete :300x10 mm

Providing and fixing aluminium handles, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade, with necessary screws etc. complete :125 mm

Providing and fixing floor mounted, white vitreous china single piece, double traps syphonic water closet of approved brand/make, shape, size and pattern including integrated white vitreous china cistern of capacity 10 litres with dual flushing system, including all fittings and fixtures with seat cover, cistern fittings, nuts, bolts and gasket etc including making connection with the existing P/S trap, complete in all respect as per directions of Engineer-in-Charge.

Providing and fixing wash basin with C.I. brackets, 15 mm dia CP Brass single hole basin mixer of approved quality and make, including painting of fittings and brackets, cutting and making good the walls wherever required:-(a) White Vitreous China Wash basin size 550x400 mm with a 15 mm CP Brass single hole basin mixer

Providing and fixing white vitreous china flat back or wall corner type lipped front urinal basin of 430x260x350 mm or 340x410x265 mm sizes respectively.

Providing and fixing C.P. brass long nose bib cock of approved quality conforming to IS standards and weighing not less than 810 gms.

Providing and fixing C.P. brass stop cock (concealed) of standard design and of approved make conforming to IS:8931.

Providing and fixing 600x450 mm beveled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete.

Providing and fixing PTMT soap Dish Holder having length of 138mm, breadth 102mm, height of 75mm with concealed fitting arrangements, weighing not less than 106 gms.

Providing and fixing PTMT towel rail complete with brackets fixed to wooden cleats with CP brass screws with concealed fittings arrangement of approved quality and colour.

Providing and fixing toilet paper holder :

Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion, (i) Single socketed pipes.12.41.2 110 mm diameter

Providing and fixing on wall face unplasticised - PVC moulded fittings/accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion.Bend 87.5° 110 mm bend

Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion, (i) Single socketed pipes. 75 mm diameter

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge. Concealed work, including cutting chases and making good the walls etc.32 mm nominal dia Pipes

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge. Concealed work, including cutting chases and making good the walls etc.20 mm nominal outer dia Pipes

Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete. Hot finished seamless type tubes

Providing corrugated G.S. sheet roofing including vertical / curved surface fixed with polymer coated J or L hooks, bolts and nuts 8 mm diameter with bitumen and G.I. limpet washers or with G.I. limpet washers rafters and trusses and including cutting to size and shape wherever required. 80 mm thick with zinc coating not less than 275 gm/m²

Providing and fixing glazed shutters for doors, windows and clerestory windows using 4 mm thick float glass panes, including ISI marked M.S. pressed butt hinges bright finished of required size with necessary screws. Second class teak wood 35 mm thick

Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) :32 mm nominal bore.

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge. Concealed work, including cutting chases and making good the walls etc. 20 mm nominal outer dia Pipes

Supplying and fitting all necessary branded sanitary fittings for a VIP&VVIP bathrooms as directed by the department for Minister's Colony's Quarter,Dispur,Guwahati-6.

Supplying and installation of FRP Iron Removal Filter, (4-5 m3/hr) capacity as directed by the department for Ministers' Colony Quarter,Dispur,Guwahati-6

Supplying and fitting Siltank Supreme 2000Ltr 3 Layred White with all necessary branded materials for water tank with required labour for placing the water tank as directed by the department for Ministers' Colony Quarter,Dispur,Guwahati-6.

Providing and laying Vitrified tiles in floor in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS:15622, of approved brand & manufacturer, in all colours and shade, laid on 20 mm thick cement mortar 1:4 (1 cement: 4 coarse sand) jointing with grey cement slurry @3.3 kg/sqm including grouting the joints with white cement and matching pigments etc. The tiles must be cut with the zero chipping diamond cutter only . Laying of tiles will be done with the notch trowel, plier, wedge, clips of required thickness, leveling system and rubber mallet for placing the tiles gently and easily. Size of Tile 1200 x 1200 mm

Providing and fixing 25 mm thick shutters for cup board etc. :9.16.1 Panelled or panelled & glazed shutters : Second class teak wood including ISI marked anodised aluminium butt hinges with necessary screws

Providing and fixing stainless steel ( Grade 304) railing made of Hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, i/c fixing the railing with necessary accessories & stainless steel dash fasteners , stainless steel bolts etc., of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-incharge, (for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasteners etc.).

Providing 10 mm thick plaster of Paris (gypsum anhydrous) ceiling up to a height of 5 m above floor level, over first class kail wood strips 25x6 mm with 10 mm gap in between and reinforced with rabbit wire mesh fixed to wooden frame (frame work to be paid separately):Flat surfaces

Providing and fixing 18 mm thick gang saw cut, mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels.8.2.2 Granite stone slab colour black, Cherry/Ruby red 8.2.2.1 Area of slab upto 0.50 sqm

Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS: 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade complete.

Supplying and fitting all necessary branded materials for Modular kitchen & pantry cabinet including hardware fittings, base cabinet & wall shutters, fillers, front shutters, base & wall cabinets etc. as directed by the department for SMinisters' Colony Quarter,Dispur,Guwahati-6

Providing, fitting and fixing Wall Paper of reputed make over finished wall after cleaning the surface etc. complete as firected.

Providing, fitting and fixing PVC pannels for walls and Ceillings (Plain) with materials , installations including Labour, carriage etc. as directed and specified.

Supplying, fitting and fixing of Roller Blinds ultra spring system of reputed make and shade design as per choice.

Providing, fitting and fixing of panelling in column, walls, doors, windows frames upto ceiling level where necessary with 19mm thick ply wood board and pasting with 1mm thick century laminates and making gooves or making design as per approved drawings icluding varnishing and polishing where ever necessary complete as per direction of the department.

Supplying, fitting and fixing Toughened glass partition with sliding arrangement with SS steel frame upto a ht. of 2.108m made of 12mm Tinted glass with all accessories etc. complete and as directed.

Providing and fixing plain multipurpose cement board(Hight pressure steam cured) with suitable screws for cement particle board in ceiling etc. complete (frame work to be paid seperatately). 6 mm thick Cement fiber board as per IS: 14862

Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / paneling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing, paneling and dash fasteners to be paid for separately) : For fixed portion Anodised aluminium (anodised transparent or dyed to required shade according to IS: 1868, Minimum anodic coating of grade AC 15)

Providing corrugated G.S. sheet roofing including vertical / curved surface fixed with polymer coated J or L hooks, bolts and nuts 8 mm diameter with bitumen and G.I. limpet washers or with G.I. limpet washers rafters and trusses and including cutting to size and shape wherever required. 0.63 mm thick with zinc coating not less than 275 gm/ m²

Providing and fixing white vitreous china pedestal type water closet (European type W.C. pan) with seat and lid, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever), conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required : W.C. pan with ISI marked white solid plastic seat and lid

Providing and fixing C.P. brass shower rose with 15 or 20 mm inlet : 100 mm diameter

Earth work in excavation by mechanical means (Hydraulic excavator) / manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, lift upto 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m.

Reinforced cement concrete work in walls (any thickness), including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts and struts etc. above plinth level up to floor five level, excluding cost of centering, shuttering, finishing and reinforcement : 1:1.5:3 (1 cement : 1.5 coarse sand incuding manufactured sand derived from Recycled Concrete Aggregate (RCA) upto 20% : 3 graded stone aggregate 20 mm nominal size Recycled Concrete Aggregate (RCA) upto 20%

20 mm cement plaster of mix : 1:4 (1 cement: 4 fine sand)

Steel work welded in built up sections/ framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required. In gratings, frames, guard bar, ladder, railings, brackets, gates and similar works.

Painting Steel work with Deluxe Multi Surface Paint to give an even shade. Two or more coat applied @ 0.90 ltr/10 sqm over an under coat of primer applied @ 0.80 ltr/ 10 sqm of approved brand or manufacture

Excavating, supplying and filling of local earth (including royalty) by mechanical transport upto a lead of 5km also including ramming and watering of the earth in layers not exceeding 20 cm in trenches, plinth, sides of foundation etc. complete.

Providing and laying Ceramic glazed floor tiles of size 300x300 mm (thickness to be specified by the manufacturer) of 1st quality conforming to IS : 15622 of approved make in colours such as White, Ivory, Grey, Fume Red Brown, laid on 20 mm thick cement mortar 1:4 (1 Cement : 4 Coarse sand), Jointing with grey cement slurry @ 3.3 kg/sqm including pointing the joints with white cement and matching pigment etc., complete.

Providing and laying factory made chamfered edge Cement Concrete paver blocks in footpath, parks, lawns, drive ways or light traffic parking etc, of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over 50mm thick compacted bed of sand, compacting and proper embedding/laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand. complete all as per direction of Engineer-in-Charge. 60mm thick cement concrete paver block of M-35 grade with approved colour, design & pattern.

16.78 Construction of granular sub-base by providing close graded Material conforming to specifications, mixing in a mechanical mix plant at OMC, carriage of mixed material by tippers to work site, for all leads & lifts, spreading in uniform layers of specified thickness with motor grader on prepared surface and compacting with vibratory power roller to achieve the desired density, complete as per specifications and directions of Engineer-in-Charge.16.78.3 With material conforming to Grade-III (size range 26.5 mm to 0.075 mm ) having CBR Value-20

Construction of granular sub-base by providing close graded Material conforming to specifications, mixing in a mechanical mix plant at OMC, carriage of mixed material by tippers to work site, for all leads & lifts, spreading in uniform layers of specified thickness with motor grader on prepared surface and compacting with vibratory power roller to achieve the desired density, complete as per specifications and directions of Engineer-in-Charge.With material conforming to Grade-II (size range 53 mm to 0.075 mm ) having CBR Value-25

Laying, spreading and compacting stone aggregate of specified sizes to WBM specifications in uniform thickness, hand picking, rolling with 3 wheeled road/vibratory roller 8-10 tonne capacity in stages to proper grade and camber, applying and brooming requisite type of screening / binding material to fill up interstices of coarse aggregate, watering and compacting to the required density .

Providing and applying tack coat using hot straight run bitumen of grade VG - 10, including heating the bitumen, spraying the bitumen with mechanically operated spray unit fitted on bitumen boiler, cleaning and preparing the existing road surface as per specifications :On W.B.M. @ 0.75 Kg / sqm

2.5 cm premix carpet surfacing with 3 cum of stone chippings 10 mm nominal size per 100 sqm and bitumen emulsion (medium setting min. 65% bitumen contents) complying with IS : 8887, using 96 kg per cum of chippings of road surface, including consolidation with road roller etc complete.

Providing and laying seal coat of premixed fine aggregate ( passing 2.36 mm and retained on 180 micron sieve) with bitumen using 128 kg of bitumen of grade VG - 10 bitumen per cum of fine aggregate and 0.60 cum of fine aggregate per 100 sqm of road surface, including rolling and finishing with road roller all complete.

Constructing masonry Chamber 60x60x75 cm inside, in brick work in cement mortar 1:4 (1 cement : 4 coarse sand) for sluice valve, with C.I. surface box 100mm top diameter, 160 mm bottom diameter and 180 mm deep ( inside) with chained lid and RCC top slab 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20mm nominal size ) , i/c necessary excavation, foundation concrete 1:5:10 (1 cement : 5 fine sand : 10 graded stone aggregate 40 mm nominal size) and inside plastering with cement mortar 1:3 (1 cement : 3 coarse sand) 12 mm thick, finished with a floating coat of neat cement complete as per standard design : With common burnt clay F.P.S.(non modular) bricks of class designation 7.5

Supplying and planting of Aesthetic Plant Chandan Varregated Hedge (Size 300 mm) on landscap ground including the preparation of the pit removing unwanted debrises filling the pit with manure and fertilizers as per specification and necessary maintenance for a period of 6 months from the date planting complete as specified and directed.

Supplying and fitting 4.5 kg Capacity CO2 type fire extinguisher with labour as directed by the department for Ministers' Colony Quarter,Dispur,Guwahati-6

Dismantling steel work manually/ by mechanical means in built up sections without dismembering and stacking within 50 metres lead as per direction of Engineer-in-charge.

Providing and fixing Pre-laminated flat pressed 3 layer (medium density) particle board or graded wood particle board IS : 3087 marked, with one side decorative and other side balancing lamination Grade I, Type II exterior grade IS : 12823 marked, in shelves with screws and fittings wherever required, edges to be painted with polyurethane primer (fittings to be paid separately). 18 mm thick

Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge . (Cost of aluminium snap beading shall be paid in basic item):With float glass panes of 8 mm thickness (weight not less than 20 kg/sqm)

Painting with synthetic enamel paint of approved brand and manufacture to give an even shade : Two or more coats on new work

Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit, with modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable etc. as required (Group C)

Wiring for twin control light point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit, 2 way modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable etc. as required.

Wiring for light/ power plug with 2X4 sq. mm FRLS PVC insulated copper conductor single core cable in surface/ recessed medium class PVC conduit alongwith 1 No. 4 sq. mm FRLS PVC insulated copper conductor single core cable for loop earthing as required.

Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required.2 X 1.5 sq. mm + 1 X 1.5 sq. mm earth wire

Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required.2 X 2.5 sq. mm + 1 X 2.5 sq. mm earth wire

Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required.2 X 4 sq. mm + 1 X 4 sq. mm earth wire

Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required.2 X 6 sq. mm + 1 X 6 sq. mm earth wire

Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required.4 X 10 sq. mm + 2 X 6 sq. mm earth wire

Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required.4 X 16 sq. mm + 2 X 6 sq. mm earth wire

Supplying and drawing following pair 0.5 mm dia FRLS PVC insulated annealed copper conductor, unarmored telephone cable in the existing surface/ recessed steel/ PVC conduit as required4 Pair

Supplying and drawing co-axial TV cable RG-6 grade, 0.7 mm solid copper conductor PE insulated, shielded with fine tinned copper braid and protected with PVC sheath in the existing surface/ recessed steel/ PVC conduit as required.

Supplying and fixing of following sizes of medium class PVC conduit along with accessories in surface/recess including cutting the wall and making good the same in case of recessed conduit as required25 mm

Supplying and fixing of following sizes of medium class PVC conduit along with accessories in surface/recess including cutting the wall and making good the same in case of recessed conduit as required32 mm

Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required. 5/6 A switch

Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required. 2 way 5/6 A switch

Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required. 15/16 A switch

Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required.3 pin 5/6 A socket outlet

Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required. 6 pin 15/16 A socket outlet

Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required. Telephone socket outlet

Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required. TV antenna socket outlet

Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required. Bell push

Supplying and fixing two module stepped type electronic fan regulator on the existing modular plate switch box including connections but excluding modular plate etc. as required.

Supplying and fixing modular blanking plate on the existing modular plate & switch box excluding modular plate as required.

Supplying and fixing following size/ modules, GI box alongwith modular base & cover plate for modular switches in recess etc. as required. 3 Module (100mmX75mm)

Supplying and fixing following size/ modules, GI box alongwith modular base & cover plate for modular switches in recess etc. as required. 4 Module (125mmX75mm)

Supplying and fixing following size/ modules, GI box alongwith modular base & cover plate for modular switches in recess etc. as required. 6 Module (200mmX75mm)

Supplying and fixing following size/ modules, GI box alongwith modular base & cover plate for modular switches in recess etc. as required. 8 Module (125mmX125mm)

Supplying and fixing following size/ modules, GI box alongwith modular base & cover plate for modular switches in recess etc. as required. 12 Module (200mmX150mm)

Supplying and fixing following Modular base & cover plate on existing modular metal boxes etc. as required. 3 Module

Supplying and fixing following Modular base & cover plate on existing modular metal boxes etc. as required. 4 Module

Supplying and fixing following Modular base & cover plate on existing modular metal boxes etc. as required. 6 Module

Supplying and fixing following Modular base & cover plate on existing modular metal boxes etc. as required. 8 Module

Supplying and fixing following Modular base & cover plate on existing modular metal boxes etc. as required. 12 Module

Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 3 pin 5/6 A modular socket outlet and 5/6 A modular switch, connections etc. as required.

Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 6 pin 5/6 & 15/16 A modular socket outlet and 15/16 A modular switch, connections etc. as required

Supplying and fixing call bell/ buzzer suitable for single phase, 230 V, complete as required.

Installation, testing and commissioning of ceiling fan, including wiring the down rods of standard length (upto 30 cm) with 1.5 sq. mm FRLS PVC insulated, copper conductor,single core cable etc. as required.

Installation of exhaust fan in the existing opening, including making good the damage, connection, testing, commissioning etc. as required Upto 450 mm sweep

Supplying and drawing of UTP 4 pair CAT 6 LAN Cable in the existing surface/ recessed Steel/ PVC conduit as required. 3 run of cable

Providing and fixing following rating and breaking capacity and pole MCCB with thermomagnetic release and terminal spreaders in existing cubicle panel board including drilling holes in cubicle panel, making connections, etc. as required.100 A,30KA,FPMCCB

Providing and fixing following rating and breaking capacity and pole MCCB with thermomagnetic release and terminal spreaders in existing cubicle panel board including drilling holes in cubicle panel, making connections, etc. as required.250 A,36KA,FPMCCB

Supplying and fixing following way, horizontal type three pole and neutral, sheet steel, MCB distribution board, 415 V, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator) 6 way (4 + 18), Double door

Supplying and fixing following way, horizontal type three pole and neutral, sheet steel, MCB distribution board, 415 V, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator)8 way (4 + 24), Double door

Supplying and fixing of following ways surface/ recess mounting, vertical type, 415 V, TPN MCB distribution board of sheet steel, dust protected, duly powder painted, inclusive of 200 A tinned copper bus bar, common neutral link, earth bar, din bar for mounting MCBs (but without MCBs and incomer ) as required . (Note : Vertical type MCB TPDB is normally used where 3 phase outlets are required.) 8 way (4 + 24), Double door

Earthing with G.I. earth plate 600 mm X 600 mm X 6 mm thick including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe of 2.7 metre long etc. (but without charcoal/ coke and salt ) as required

Earthing with copper earth plate 600 mm X 600 mm X 3 mm thick including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe of 2.7 metre long etc. with charcoal/ coke and salt as required

Supplying and laying 25 mm X 5 mm copper strip at 0.50 metre below ground as strip earth electrode, including connection/ terminating with nut, bolt, spring, washer etc. as required. (Jointing shall be done by overlapping and with 2 sets of brass nut bolt & spring washer spaced at 50mm)

Supply, Installation, Testing and Commissioning of 1200 mm sweep, BEE 5 star rated, ceiling fan with Brush Less Direct Current (BLDC) Motor, class of insulation: B, 3 nos. blades, 30 cm long down rod, 2 nos. canopies, shackle kit, safety rope, copper winding, Power Factor not less than 0.9, Service Value (CMM/W) minimum 6.85, Air delivery minimum 215 CMM, 350 RPM (tolerance as per IS : 374- 2019), THD less than 10%, remote or electronic regulator unit for speed control and all remaining accessories including safety pin, nut bolts, washers, temperature rise=75 degree C (max.), insulation resistance more than 2 mega ohm, suitable for 230 V, 50 Hz, single phase AC Supply, earthing etc. complete as required.

Supplying, installation, testing and Commission of the following indoor Decorative Recess mounted LED down lighter luminaries of 15W Led Recessed Luminaire Philips complete with all accessories such as ballast, starter etc. In the false ceiling type Armstrong /Gypsum or similar ceiling mounting with necessary support with 1.5 sq.mm. P.V.C. insulated S.C.copper conductor as required and as directed by the department ( Philips/Jaquar / LT / Wipro make).15 W Recessed LED Down Light

Supplying, installation, testing and Commission of the following JAQUAR LIGHTING 12W Led Recessed Luminaire JAQUAR LIGHTING ((LNEP01S012XC)) 12W complete with all accessories such as ballast, starter etc. In the false ceiling type Armstrong /Gypsum or similar ceiling mounting with necessary support with 1.5 sq.mm. P.V.C. insulated S.C.copper conductor as required and as directed by the department ( Philips/Jaquar / LT / Wipro make).JAQUAR LIGHTING 12W

Supplying, installation, testing and Commission of the following indoor Decorative Recess mounted LED COB down lighter luminaries of LED 3W Led Recessed Luminaire complete with all accessories such as ballast, starter etc. In the false ceiling type Armstrong /Gypsum or similar ceiling mounting with necessary support with 1.5 sq.mm. P.V.C. insulated S.C.copper conductor as required and as directed by the department ( Philips/Jaquar / LT / Wipro make).LED 3W Led COB Recessed Luminaire

Supply, installation, testing and commissioning of LED light fixtures suitable for any modern workspace Linea LED Strip Light Premium 50W with driver , Electronic Balast/Adaptor similar to Wipro make- or its equivalent . 50 Watt Striep light

Supplying including fitting fixing of 200 MM CRISP AIR EXHAUST FAN in the existing hole on the wall of following sweeps with making necessary connection as required complete

Supplying with fitting and fixing Venus 25 liter 4 Star Water Heater Venus (Venus Splash Copper 25CU) Availability: 100 In Stock Min. Qty. Per Consignee: 15 of the following specification complete including making necessary connection as approved, specified and directed by the deptt. Venus 25 liter 4 Star Water Heater Venus (Venus Splash Copper 25CU)

Supplying with fitting and fixing of Led Bollard Light 15W including making necessary connection as per direction of department. Led Bollard Light 15W

Supplying with fitting and fixing DECOREX Led Garden Light, Warranty for (DECOREX-JSBGN-15W) of the following specification complete including making necessary connection as approved, specified and directed by the deptt. DECOREX Led Garden Light, DECOREX (DECOREX-JSBGN-15W)

Supplying including installation, commissioning of 'G Frame Panel board O/G TP MCCB indoor type floor mounting compartmentalize panel board of Double Door 6 Nos Out going 250 Amps "AA" Frame MCCB Item Code No. IHVG02500600 complete . The panel board is to be erected in 1 : 3 : 6 PCC foundation including brick soling / grouting etc. complete neatly Wiring done as specified and directed by the deptt. confirming to IP 43 protection.

Supplying installation testing and commissioning of FWJ- Single phase SS body self priming pressure pump 4.00 sq mm copper multstrand wire connection an as specified and directed by the Deptt.Crompton /Wilo Make. 1HP PRESSURE PUMP

Supplying with fitting and fixing (95 SQMM 3.5 CORE ISI MARKED 1100 VOTS GRADE (Anchor) of the following specification complete including making necessary connection as approved, specified and directed by the deptt. (95 SQMM 3.5 CORE ISI MARKED 1100 VOTS GRADE (Anchor)

Supplying with fitting and fixing LT XLPE Armoured Cables of Size 2 Core x 6 Sq.mm of the following specification complete including making necessary connection as approved, specified and directed by the deptt. (LT XLPE Armoured Cables of Size 2 Core x 6 Sq.mm

Supplying with fitting and fixing LG 420 L 3 Star Frost Free Double Door Refrigerator LG (LG 420 E STAR) Availability: 10 In Stock Min. Qty. Per Consignee: 5 R complete including making necessary connection as approved, specified and directed by the deptt. LG 420 L 3 Star Frost Free Double Door Refrigerator LG (LG 420 E STAR)

Supplying with fitting and fixing SSFW true domestic microwave oven LED Watts SSFW (HAO-50LD) R complete including making necessary connection as approved, specified and directed by the deptt. SSFW true domestic microwave oven LED Watts SSFW (HAO-50LD)

Supplying with fitting and fixing of GLEN Wall Mount Mesh Filter Decorative Kitchen Chimney GLEN (AUTO CLEAN BLACK DECORATIVE SHAPE CHIMNEY 90 CM 1400 M3/H FI MODEL complete including making necessary connection as approved, specified and directed by the deptt.Decorative Kitchen Chimney GLEN (AUTO CLEAN BLACK DECORATIVE SHAPE CHIMNEY 90 CM 1400 M3/H FI

Supplying with fitting and fixing of Aqua IGS Fully automatic with auto cut off RO +UV Potable Water Purification System Aqua IGS (100 LPH Industrial RO+UV) complete including making necessary connection as approved, specified and directed by the deptt.Aqua IGS Fully automatic with auto cut off RO +UV Potable Water Purification System Aqua IGS (100 LPH Industrial RO+UV)

Supplying with fitting and fixing of Ceiling Fan Model model AEROCOOL 1360 mm White Aqua as specified and Directed by the Deptt.

88 HP VRF Air Conditioner System PART - A (SUPPLY OF MACHINES) VRF ODU (VOLTAS MAKE) Supply of Voltas make Variable Refigerant Flow (VRF) air- conditioning system with higly efficient DC inverter driven Scroll/Rotary compressors suitable for both Heating & Cooling mode complete with indoor and outdoor units with individual controllers and with fittings etc, as per quantity given below. The compressors have a intelligent soft start technology to achieve the set temperature quickly . The VRF units have wide operational range from -20 DEG C to 50 DEG C to ensure stable operation. The units are precharged with R-410A refrigerant gas, complete with duly powder coated etc as required. The outdoor unit heat exchangers have innovatively designed inner grooved type copper piping to enhance heat exchange and increase the subcooling of refrigerant to reduce system resistance and improve reliablility.The heat exchangers are specially designed for corrosion resistance with blue fin treatment. The units are Modbus Compatiable and have special night time silent operational feature. 24HP

88 HP VRF Air Conditioner System PART - A (SUPPLY OF MACHINES) VRF ODU (VOLTAS MAKE) Supply of Voltas make Variable Refigerant Flow (VRF) air- conditioning system with higly efficient DC inverter driven Scroll/Rotary compressors suitable for both Heating & Cooling mode complete with indoor and outdoor units with individual controllers and with fittings etc, as per quantity given below. The compressors have a intelligent soft start technology to achieve the set temperature quickly . The VRF units have wide operational range from -20 DEG C to 50 DEG C to ensure stable operation. The units are precharged with R-410A refrigerant gas, complete with duly powder coated etc as required. The outdoor unit heat exchangers have innovatively designed inner grooved type copper piping to enhance heat exchange and increase the subcooling of refrigerant to reduce system resistance and improve reliablility.The heat exchangers are specially designed for corrosion resistance with blue fin treatment. The units are Modbus Compatiable and have special night time silent operational feature. 22HP

88 HP VRF Air Conditioner System PART - A (SUPPLY OF MACHINES) VRF ODU (VOLTAS MAKE) Supply of Voltas make Variable Refigerant Flow (VRF) air- conditioning system with higly efficient DC inverter driven Scroll/Rotary compressors suitable for both Heating & Cooling mode complete with indoor and outdoor units with individual controllers and with fittings etc, as per quantity given below. The compressors have a intelligent soft start technology to achieve the set temperature quickly . The VRF units have wide operational range from -20 DEG C to 50 DEG C to ensure stable operation. The units are precharged with R-410A refrigerant gas, complete with duly powder coated etc as required. The outdoor unit heat exchangers have innovatively designed inner grooved type copper piping to enhance heat exchange and increase the subcooling of refrigerant to reduce system resistance and improve reliablility.The heat exchangers are specially designed for corrosion resistance with blue fin treatment. The units are Modbus Compatiable and have special night time silent operational feature. 20HP

VRF INDOOR UNITS Supply of VRF Indoor units address setting and capacity as mentioned below. Multi speed motor, coil section with DX coil, outer cabinet, drain pan mechanism insulation, pipe connections of various capacities Supply of 4-Way Cassette Units with Cordless Remote 4-Way Cassette Units-1TR

VRF INDOOR UNITS Supply of VRF Indoor units address setting and capacity as mentioned below. Multi speed motor, coil section with DX coil, outer cabinet, drain pan mechanism insulation, pipe connections of various capacities Supply of 4-Way Cassette Units with Cordless Remote 4-Way Cassette Units-1.6TR

VRF INDOOR UNITS Supply of VRF Indoor units address setting and capacity as mentioned below. Multi speed motor, coil section with DX coil, outer cabinet, drain pan mechanism insulation, pipe connections of various capacities Supply of 4-Way Cassette Units with Cordless Remote 4-Way Cassette Units-2TR

VRF INDOOR UNITS Supply of VRF Indoor units address setting and capacity as mentioned below. Multi speed motor, coil section with DX coil, outer cabinet, drain pan mechanism insulation, pipe connections of various capacities Supply of 4-Way Cassette Units with Cordless Remote 4-Way Cassette Units-2.6TR

VRF INDOOR UNITS Supply of VRF Indoor units address setting and capacity as mentioned below. Multi speed motor, coil section with DX coil, outer cabinet, drain pan mechanism insulation, pipe connections of various capacities Supply of 4-Way Cassette Units with Cordless Remote 4-Way Cassette Units-3.2TR

Supply of 1-Way Cassette Units with Cordless Remote 1-Way Cassette Units-2TR

Supply of 1-Way Cassette Units with Cordless Remote 1-Way Cassette Units-1.6TR

INDOOR REFNETSSupply of individual Y joints/refnet joints for connecting IDU with Refrigerant Piping

INDOOR REFNETSSupply of individual Y joints/refnet joints for connecting IDU with Refrigerant Piping Supply, Installation, Testing & Commissioning of Low-side Works of HVAC SystemInstallation, Testing and Commissioning of 415V , 3 Ph - 50HZ Aircooled Type Top Discharge VRF SYSTEM Unit, compresing of inverter technology based heametically sealed scroll/Rotary compressor with R410a Refrigerant, Aircooled Condenser along with inbuilt microprocessor panel.24HP

INDOOR REFNETSSupply of individual Y joints/refnet joints for connecting IDU with Refrigerant Piping Supply, Installation, Testing & Commissioning of Low-side Works of HVAC SystemInstallation, Testing and Commissioning of 415V , 3 Ph - 50HZ Aircooled Type Top Discharge VRF SYSTEM Unit, compresing of inverter technology based heametically sealed scroll/Rotary compressor with R410a Refrigerant, Aircooled Condenser along with inbuilt microprocessor panel.22HP

INDOOR REFNETSSupply of individual Y joints/refnet joints for connecting IDU with Refrigerant Piping Supply, Installation, Testing & Commissioning of Low-side Works of HVAC SystemInstallation, Testing and Commissioning of 415V , 3 Ph - 50HZ Aircooled Type Top Discharge VRF SYSTEM Unit, compresing of inverter technology based heametically sealed scroll/Rotary compressor with R410a Refrigerant, Aircooled Condenser along with inbuilt microprocessor panel.20HP

IDU Installation VRF INDOOR UNITS Installation,Testing & Commissioning of 4-Way Cassette Units with Cordless Remote 4-Way Cassette Units-1TR

IDU Installation VRF INDOOR UNITS Installation,Testing & Commissioning of 4-Way Cassette Units with Cordless Remote 4-Way Cassette Units-1.6TR

IDU Installation VRF INDOOR UNITS Installation,Testing & Commissioning of 4-Way Cassette Units with Cordless Remote 4-Way Cassette Units-2TR

IDU Installation VRF INDOOR UNITS Installation,Testing & Commissioning of 4-Way Cassette Units with Cordless Remote 4-Way Cassette Units-2.6TR

IDU Installation VRF INDOOR UNITS Installation,Testing & Commissioning of 4-Way Cassette Units with Cordless Remote 4-Way Cassette Units-3.2TR

Installation,Testing & Commissioning of 1-Way Cassette Units with Cordless Remote 1-Way Cassette Units-2TR

Installation,Testing & Commissioning of 1-Way Cassette Units with Cordless Remote 1-Way Cassette Units-1.6TR

Installation,Testing & Commissioning of 1-Way Cassette Units with Cordless Remote IDU Refnets

PIPING Supply,installation, testing and commissioning of Interconnecting refrigerant pipe work with (19mm/13 mm thick) closed cell elastomeric nitrile rubber tubular insulation between each set of indoor & outdoor units as per specifications, all piping.(Make-Mandev) 41.3mm

PIPING Supply,installation, testing and commissioning of Interconnecting refrigerant pipe work with (19mm/13 mm thick) closed cell elastomeric nitrile rubber tubular insulation between each set of indoor & outdoor units as per specifications, all piping.(Make-Mandev) 38.1mm

PIPING Supply,installation, testing and commissioning of Interconnecting refrigerant pipe work with (19mm/13 mm thick) closed cell elastomeric nitrile rubber tubular insulation between each set of indoor & outdoor units as per specifications, all piping.(Make-Mandev) 34.93mm

PIPING Supply,installation, testing and commissioning of Interconnecting refrigerant pipe work with (19mm/13 mm thick) closed cell elastomeric nitrile rubber tubular insulation between each set of indoor & outdoor units as per specifications, all piping.(Make-Mandev)31.8mm

PIPING Supply,installation, testing and commissioning of Interconnecting refrigerant pipe work with (19mm/13 mm thick) closed cell elastomeric nitrile rubber tubular insulation between each set of indoor & outdoor units as per specifications, all piping.(Make-Mandev)28.6mm

PIPING Supply,installation, testing and commissioning of Interconnecting refrigerant pipe work with (19mm/13 mm thick) closed cell elastomeric nitrile rubber tubular insulation between each set of indoor & outdoor units as per specifications, all piping.(Make-Mandev)25.4mm

PIPING Supply,installation, testing and commissioning of Interconnecting refrigerant pipe work with (19mm/13 mm thick) closed cell elastomeric nitrile rubber tubular insulation between each set of indoor & outdoor units as per specifications, all piping.(Make-Mandev)22.2mm

PIPING Supply,installation, testing and commissioning of Interconnecting refrigerant pipe work with (19mm/13 mm thick) closed cell elastomeric nitrile rubber tubular insulation between each set of indoor & outdoor units as per specifications, all piping.(Make-Mandev) 19.6mm

PIPING Supply,installation, testing and commissioning of Interconnecting refrigerant pipe work with (19mm/13 mm thick) closed cell elastomeric nitrile rubber tubular insulation between each set of indoor & outdoor units as per specifications, all piping.(Make-Mandev)15.9mm

PIPING Supply,installation, testing and commissioning of Interconnecting refrigerant pipe work with (19mm/13 mm thick) closed cell elastomeric nitrile rubber tubular insulation between each set of indoor & outdoor units as per specifications, all piping.(Make-Mandev)12.7mm

PIPING Supply,installation, testing and commissioning of Interconnecting refrigerant pipe work with (19mm/13 mm thick) closed cell elastomeric nitrile rubber tubular insulation between each set of indoor & outdoor units as per specifications, all piping.(Make-Mandev)9.5mm

PIPING Supply,installation, testing and commissioning of Interconnecting refrigerant pipe work with (19mm/13 mm thick) closed cell elastomeric nitrile rubber tubular insulation between each set of indoor & outdoor units as per specifications, all piping.(Make-Mandev)6.35mm

SITC of Drain Piping of 25 mm dia with insulation

REFRIGERANT GAS SITC of Refrigerant R-410a

COMMUNICATION LINE SITC of Control Cable(3CX 1.0SQMM /As required Shielded copper Cable or as per units specifications)

Lifting & Shifting Lifting and Shifting of IDU & ODU

VI PAD for ODU

Hanging Arrangements for copper & Drain Pipe Line

Cable Tray Cable for Exoposed Pipe

Audio Vedio & Wifi Networking System 85" LED display which support 4K &FullHD Content Having brightness of 300 nts minimum having having HDMI input . Brand Samsung

Audio Vedio & Wifi Networking System Video Conference Device with 12x PTZ Camera with 12 months Service Pack . Brand Cisco

Audio Vedio & Wifi Networking System Video conference Device Table Microphone with Jack Plug with service pack.Brand Cisco

Audio Vedio & Wifi Networking System Video Conference - Cloud Meeting Webex software licence. Brand - Cisco

Audio Vedio & Wifi Networking System HDMI Over Cat6 Extender supporting 40 Mtrs Full HD resolution to transmit HDMI Signal over long distance using CAT6 Cable

Audio Vedio & Wifi Networking System HDMI Switcher 4 in 1 Out for input from PopUp Box, VC

Audio Vedio & Wifi Networking System HDMI Cable 2 Mtrs supporting HDMI 2.0

Audio Vedio & Wifi Networking System Wall mount speaker having 120 watts power output with front grill , 8 ohms,Wall bracket included with speaker. Brand JBL

Audio Vedio & Wifi Networking System Column Speaker having 240 Watts power output with multiple speakers used mainly for Vocal purpose with front grill,8 ohms with bracket for installation. Brand - JBL Amplifier for Wal

Audio Vedio & Wifi Networking System Amplifier for Wall Mount Speaker. Brand - JBL/ Crown

Audio Vedio & Wifi Networking System Amplifier for Column Speaker. Brand - JBL/ Crown

Audio Vedio & Wifi Networking System Microphone Cable

Audio Vedio & Wifi Networking System OFC Speaker Cable of 2 core x 1.5 sqmm capable of handling power upto 300 Watts

Audio Vedio & Wifi Networking System PVC Conduit / Cashing

Audio Vedio & Wifi Networking System Pop Up Box with HDMI , Power

Audio Vedio & Wifi Networking System 08 Port POE Switch

Audio Vedio & Wifi Networking System CAT6 Cable

Audio Vedio & Wifi Networking System Electrical Cable for Video Wall , Amplifier etc

Audio Vedio & Wifi Networking System System Rack for mounting of Amplifier , Processor

Audio Vedio & Wifi Networking System Connectors, Patch cord, Jointer,XLR, etc

Audio Vedio & Wifi Networking System 5 KVA Online UPS with 30 Mins Backup Battery + Battery Rack + Interconnecting Cable

Installation , Commissioning , Testing of the System

Fire Detaction System-Smoke Detector

Fire Detaction System-Heat Detector

Fire Detaction System-Hooter

Fire Detaction System-Manual Call Point MCP

Fire Detaction System-Input Module

Fire Detaction System-Panel

Fire Detaction System-Analog EPABX Machine having 2 PNT & 10 Extensions

Fire Detaction System-RJ11 Connector

Fire Detaction System-Telephone Handset Analog

Fire Detaction System-WiFi Access Point

Fire Detaction System-Switch 8 Port

Fire Detaction System-Rack

Fire Detaction System-RJ45 Connector

Fire Detaction System-Installation & Commissioning Charge

Supplying with installation testing and commissioning of Hi -- wall 3 STAR rating non ducted split type air conditioner of the following capacity with cordless remote complete with indoor and outdoor unit, copper pipe and electrical connection up to 5 m between the room unit and out door unit (1.5 TON capacity Voltas)

Supplying with installation testing and commissioning of Hi -- wall 3 STAR rating non ducted split type air conditioner of the following capacity with cordless remote complete with indoor and outdoor unit, copper pipe and electrical connection up to 5 m between the room unit and out door unit (2 TON capacity Voltas)

Supplying with fitting and fixing VOLTRIQ Digital Volt Meter 5.0 KVA Automatic Line Voltage Corrector Or Step Type Auto Transformer VOLTRIQ of the following specification complete including making necessary connection as approved, specified and directed by the deptt. 5 KVA (SKYLAND / Vee-Dee / V GUARD / VERTEX/ INDO/ VENUS make)

Supplying including fitting fixing of following A.C. 2 Model Starter in the existing 2 model Modular board necessary connection as approved by the Deptt.)as required complete and as directed by the Department.25 Amps 2 Module Starter.

Supplying including fitting fixing of following 1.5 Ton capacity 3 Model Starter Cassatte AC necessary connection as approved by the Deptt.)as required complete and as directed by the Department.1.5 Ton capacity 3 Model Starter Cassatte AC

Supplying including fitting fixing of following 2.0 Ton capacity 3 Model Starter Cassatte AC necessary connection as approved by the Deptt.)as required complete and as directed by the Department.2.0 Ton capacity 3 Model Starter Cassatte AC

Supplying including fitting fixing of following 3.0 Ton capacity 3 Model Starter Cassatte AC necessary connection as approved by the Deptt.)as required complete and as directed by the Department.3.0 Ton capacity 3 Model Starter Cassatte AC

Supplying with installation of CUMMINS Power Generator- DG set of 500 AMF Control Panel CUMMINS (JSP 500K) including making necessary connection as approved, specified and directed by the deptt. CUMMINS Power Generator- DG set of 500 AMF Control Panel CUMMINS (JSP 500K) 500 KVA DG Ser

Supplying with installation of RPPL Distribution Transformer, 3 Phase, 11 KV, > 200 KVA Up to and including 2500 KVA RPPLR including making necessary connection as approved, specified and directed by the deptt. RPPL Distribution Transformer, 3 Phase, 11 KV, > 200 KVA Up to and including 2500 KVA RPPLR (315KVA SS)

Earthing with copper earth plate 600 mm X 600 mm X 3 mm thick including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe of 2.7 metre long etc. (but without charcoal/ coke and salt ) as required.

Supplying and laying 25 mm X 5 mm copper strip at 0.50 metre below ground as strip earth electrode, including connection/ terminating with nut, bolt, spring, washer etc. as required. (Jointing shall be done by overlapping and with 2 sets of brass nut bolt & spring washer spaced at 50mm)

Supplying with fitting and fixing GLOSTER 01 150 3.5 Aluminium Armoured cable GLOSTERR (XLPE Cable 3.5CX150 SQMM AL LT Cable as per 7098 Part 1 of the following specification complete including making necessary connection as approved, specified and directed by the deptt.GLOSTER 01 150 3.5 Aluminium Armoured cable GLOSTERR (XLPE Cable 3.5CX150 SQMM AL LT Cable as per 7098 Part 1

Supplying with fitting and fixing of (ON-Load) Changeover Switch (4 Pole) I-O-II of the following specification complete including making necessary connection as approved, specified and directed by the deptt.800 A A (ON-Load) Changeover Switch (4 Pole) I-O-II

Supplying with fitting and fixing of (ON-Load) Changeover Switch (4 Pole) I-O-II of the following specification complete including making necessary connection as approved, specified and directed by the deptt.630 A(ON-Load) Changeover Switch (4 Pole) I-O-II

Supplying with errection of 12 METER LONG STEEL TUBULAR POLE 410-SP-66 of floolwing specification complete including making necessary connection as approved, specified and directed by the deptt. 12 METER LONG STEEL TUBULAR POLE 410-SP-66

Supply of 630 Amps EDO ACB mounted , Main LT Panel made out with 2mm Thick CRCA Sheet Steel, Painted with Siemens Grey Powder coated paint after 7 tank chemical treatment process , assembling with Aluminum Busbar , Copper flexible wire and approved brad Switchgear etc

Supply of 630 Amps EDO ACB mounted , Main LT Panel made out with 2mm Thick CRCA Sheet Steel, Painted with Siemens Grey Powder coated paint after 7 tank chemical treatment process , assembling with Aluminum Busbar , Copper flexible wire and approved brad Switchgear etc

Supplying with fitting and fixing of 3Ph 4W Combined CT/PT Accuracy Class 0.5,15/5A,STC 6.4 KA for 1Sec with including making necessary connection as approved, specified and directed by the deptt. 3Ph 4W Combined CT/PT Accuracy Class 0.5,15/5A,STC 6.4 KA for 1Sec

Supplying with fitting and fixing of Disc Insulator(Porcelain) 45 KN (T&C) Type complete with including making necessary connection as approved, specified and directed by the deptt.Disc Insulator(Porcelain) 45 KN (T&C) Type

Supplying with fitting and fixing of Pin Insulator (Plymer) 5KN (FRP 24mm) complete with including making necessary connection as approved, specified and directed by the deptt.Pin Insulator (Plymer) 5KN (FRP 24mm)

Supplying with fitting and fixing of GI Channel Cross Arm(100x50x6x3200mm) complete with including making necessary connection as approved, specified and directed by the deptt.GI Channel Cross Arm(100x50x6x3200mm)

Supplying with fitting and fixing of 11Kv 5KA lighting Arrestor ( Line Type, Distribution Class) complete with including making necessary connection as approved, specified and directed by the deptt.11Kv 5KA lighting Arrestor ( Line Type, Distribution Class)

Supplying with fitting and fixing of 11KV DO Fuse Set 150A Assembly complete with including making necessary connection as approved, specified and directed by the deptt.11KV DO Fuse Set 150A Assembly

Supplying with fitting and fixing of 11kv GOAB Switch 150Amp complete with including making necessary connection as approved, specified and directed by the deptt.11kv GOAB Switch 150Amp

Supplying with fitting and fixing of 11kv Grade armoured cable 1x120 sq mm with including making necessary connection as approved, specified and directed by the deptt.11kv Grade armoured cable 1x120 sq mm

Load Security paid to be APDCL Authority for 200 KW against the 315 KVA Sub Station.

Supplying with fitting and fixing 300 Sq mm Aluminium Armoured cable (XLPE Cable 1CX300 SQMM AL LT Cable of the following specification complete including making necessary connection as approved, specified and directed by the deptt.300 Sq mm Aluminium Armoured cable (XLPE Cable 1CX300 SQMM AL LT Cable

Supplying with fitting and fixing 630 Sq mm Aluminium Armoured cable (XLPE Cable 1CX630 SQMM AL LT Cable of the following specification complete including making necessary connection as approved, specified and directed by the deptt.630 Sq mm Aluminium Armoured cable (XLPE Cable 1CX630 SQMM AL LT Cable

Supplying with fitting and fixing of 11KV 1Cx70 Sq mm AAAC Covered Conductor Medium Voltage Covered Conductor of the following specification complete including making necessary connection as approved, specified and directed by the deptt.630 Sq mm Aluminium Armoured cable (XLPE Cable 1CX630 SQMM AL LT Cable

Supplying with fitting and fixing of 11KV 1Cx70 Sq mm AAAC Covered Conductor Tention Hardwre of the following specification complete including making necessary connection as approved, specified and directed by the deptt.630 Sq mm Aluminium Armoured cable (XLPE Cable 1CX630 SQMM AL LT Cable

Supplying with fitting and fixing of 11KV 1Cx70 Sq mm AAAC Covered Conductor Tention Insulatoe of the following specification complete including making necessary connection as approved, specified and directed by the deptt.630 Sq mm Aluminium Armoured cable (XLPE Cable 1CX630 SQMM AL LT Cable

Supplying with fitting and fixing of GI Angle (50x50x6)mm of the following specification complete including making necessary connection as approved, specified and directed by the deptt.630 Sq mm Aluminium Armoured cable (XLPE Cable 1CX630 SQMM AL LT Cable

ANUPAM NIRMAN PVT. LTD.