Renovation of central store sitting area in CSIO Chandigarh

Amount

Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 12.5 in superstructure above plinth level up to floor V level in all shapes and sizes in :Cement mortar 1:4 (1 cement : 4 coarse sand)

Structural steel work riveted, bolted or welded in built up sections & Tube Section, trusses and framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete. JINDAL/TATA or Equivalent

Providing and fixing precoated galvanised iron profile sheets (size, shape and pitch of corrugation as approved by Engineer-in-charge) 0.50 mm (+ 0.05 %) total coated thickness with zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length upto 12 metre or as desired by Engineerin- charge. The sheet shall be fixed using self drilling /self tapping screws of size (5.5x 55 mm) with EPDM seal, complete upto any pitch in horizontal/ vertical or curved surfaces, excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required. MAke :- TATA/ JSW

Providing and fixing 15 cm wide, 45 cm overall semi-circular plain G.S. sheet gutter with iron brackets 40x3mm size, bolts, nuts and washers etc., including making necessary connections with rain water pipes complete. 0.80 mm thick with zinc coating not less than 275 gm/m²

Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion, (i) Single socketed pipes. 110 mm diameter Make :- Dipalst/Plasto or Equivalent

Providing and fixing M.S. holder bat clamps of approved design to C.I. or S.C.I. rain water pipes embedded in and including cement concrete blocks 10x10x10 cm of 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) and cost of cutting holes and making good the walls etc. : 100 mm diameter

Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion. Bend 87.5°. 110 mm bend Dipalst/Plasto or Equivalent

12 mm cement plaster of mix : 1:4 (1 cement: 4 fine sand)

Distempering with dry distemper of approved brand and manufacture (two or more coats) of required shade on new work, over and including water thinnable priming coat to give an even shade Make :- Asian/Narolac/Dulux.

Painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade :Two coats on old work Make :- Asian/Narolac/Dulux.

Distempering with 1st quality acrylic distemper (ready made) having VOC content less than 50 gm per ltr. of approved manufacturer and of required shade and colour complete. as per manufacturer’s specification.Two coats on old work Make :- Asian/Narolac/Dulux.

Painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade : Two or more coats on new work over an under coat of suitable shade with ordinary paint of approved brand and manufacture Make :- Asian/Narolac/Dulux.

Repairs to plaster of thickness 12 mm to 20 mm in patches of area 2.5 sq. meters and under, including cutting the patch in proper shape, raking out joints and preparing and plastering the surface of the walls complete, including disposal of rubbish to the dumping ground, all complete as per directions of Engineer-In-Charge. 14.1.1 With cement mortar 1:4 (1 cement : 4 fine sand)

Taking out existing wooden and aluminium door/Cupborad/Window shutter, repair by cutting, painting etc. and refixing of repaired door shutters to existing door frames, including replacement of hinges with screws, etc. as required, all complete as per the direction of the Engineer-in-charge.

Dismantling aluminium/ Gypsum partitions, doors, windows, fixed glazing and false ceiling including disposal of unserviceable surplus material and stacking of serviceable material with in 50 meters lead as directed by Engineer-in-charge.

Providing and fixing 12 mm thick prelaminated particle board flat pressed three layer or graded wood particle board conforming to IS: 12823 Grade l Type ll, in panelling fixed in aluminum doors, windows shutters and partition frames with C.P. brass / stainless steel screws etc. complete as per architectural drawings and directions of Engineer-in-charge Pre-laminated particle board with decorative lamination on both sides Make- Century/Novapan/MERINO

Carry out petty Job for welding works with neccesry Tools, welding set & rod etc. For petty works which otherwise can not be measured all complete as direction by Engineer in Charge

Taking out of Existing False Ceiling & Refixing the same after modification according to level & position at site.The Work will be including aluminium grid section if required additional fittings etc.complete including replacing damaged panel etc ( particle board to be supply by CSIO free of cost for this item) as per direction of engineer in charge.

SCHEDULE - I : - ELECTRICAL PART WORK Labour Charges for Dismentlling of Existing Electric points wiring, complete in all respect as incluiding shifting of material from site to store as required.

Rewiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FR PVC insulated copper conductor single core cable and 1.5 sq.mm. FR PVC insulated copper conductor single core cable as earth wire in existing surface/ recessed steel/ PVC conduit including dismantling as required. (i) Group-C (Note- Moduler box used for switches should have 25% extra space as required)

Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface/ recessed steel/ PVC conduit, with modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable etc. as required. (i) Group-C (Note- Moduler box used for switches should have 25% extra space as required)

Supplying and fixing metal box of 150 mm X 75mm X 60 mm deep (nominal size) on surface or in recess with suitable size of phenolic laminated sheet cover in front including providing and fixing 3 pin 5/6 amps socket outltet and 5/6 amps piano type switch, connection, painting etc. as required. (For light plugs to be used in non residential buildings).

Supplying and fixing metal box of 180 mm X 100 mm X 60 mm deep (nominal size) on surface or in recess with suitable size of phenolic laminated sheet cover in front including providing and fixing 6 pin 5/6 & 15/16 amps socket outlet and 15/16 amps piano type switch, connection, painting etc. as required.

Supplying and fixing of 20 mm. sizes medium class PVC conduit along with accessories in surface/ recess including cutting the wall and making goods the same in case of recessed conduit as required.

Supplying and fixing of 25 mm. sizes medium class PVC conduit along with accessories in surface/ recess including cutting the wall and making goods the same in case of recessed conduit as required.

Supplying and fixing 25 mm dia MS flexible pipe with PVC coating along with all ancillaries and accessories like coupler etc. as required.

Wiring for circuit/ submain wiring alongwith earth wire with the 2X1.5 sq mm + 1X1.5 sq mm earth wire of FRLS PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required. (Note:- this item is including PVC conduite pipe + PVC wire)

Wiring for circuit/ submain wiring alongwith earth wire with the 2X2.5 sq mm + 1X2.5 sq mm earth wire of FRLS PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required. (Note:- this item is including PVC conduite pipe + PVC wire)

Wiring for circuit/ submain wiring alongwith earth wire with the 2X4 sq mm + 1X4 sq mm earth wire of FRLS PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required. (Note:- this item is including PVC conduite pipe + PVC wire)

Supplying and fixing metal box of 180mm X 100mm X60mm (nominal sizes) on surface or in recess with suitable size of phenolic laminated sheet cover in front including painting etc. as required.

Supplying and fixing metal box of 200mm X 125mm X60mm (nominal sizes) on surface or in recess with suitable size of phenolic laminated sheet cover in front including painting etc as required.

Supplying and fixing metal box of 200mm X 300mm X100mm (nominal sizes) on surface or in recess with suitable size of phenolic laminated sheet cover in front including painting etc as required.

Supplying and fixing piano type 5/6 amps switch on the existing switch box/ cover including connections etc. as required.

Supplying and fixing piano type 15/16 amps switch on the existing switch box/ cover including connections etc. as required.

Supplying and fixing piano type 3 pin 5/6 amp socket outlet on the existing switch box/ cover including connections etc. as required.

Supplying and fixing piano type 6 pin 15/16 amp socket outlet on the existing switch box/ cover including connections etc. as required.

Supplying and Errection of Bakelite sheet of 2mm thick, ISI marked with cutting etc. anyone of make Heylem/Super Heylem.

Supplying and fixing of U-PVC adaptable trunking system of size 100mm X 50mm complete with trunking cover etc. for housing the electrical modular box for fixing modular switch sockets, telephone socket etc, on the wall/tables/pillars etc. as required.

Supply and fixing of PVC moduler box 6 to 8 modules with cover plate and blanking plate suitable for fixing in 100mmx50mm U-PVC trunking for fixing the moduler switch and socket 5amp./15amp. Complete as required at site.

Supply and fixing of RJ45 CAT6 Computer Jack with PVC modular box , base and cover plate suitable for fixing in 100mm x 50mm U-PVC trunking complete as required at site.

Supply and fixing of RJ11 1 line Telephone Jack with PVC modular box , base and cover plate suitable for fixing in 100mm x 50mm U-PVC trunking complete as required at site.

Supplying and fixing 5/6 amp moduler switch on the existing moduler plate and switch box including connections but excluding moduler plate etc. as required.

Supplying and fixing 15/16 amp moduler switch on the existing moduler plate and switch box including connections but excluding moduler plate etc. as required.

Supplying and fixing 3 pin 5/6 amp moduler socket outlet on the existing moduler plate and switch box including connections but excluding moduler plate etc. as required.

Supplying and fixing 6 pin 15/16 amp moduler socket outlet on the existing moduler plate and switch box including connections but excluding moduler plate etc. as required.

Supply of full glow G5 recessed type 30W LED Light Fitting of size 2' x 2', lumens - 3600 or more, operating voltage 230/250 Volts, 50Hz, suitable for office and complete in all respect with driver etc. Model/Make: RC370B LED36S of Philips OR equivalent model of Havells, CG or Wipro. (Model should be got approved before installation of the fitting)

Installation ,Testing, Commissioning of wall bracket /ceiling fittings of all sizes and shapes containing upto two GLS/CFL/LED lamps per fitting, complete with all accessories including connections etc. as required.

Laying and fixing of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of size Upto 35 sq. mm (clamped with 1mm thick saddle) on wall surface as required.

Supply & making End termination with brass compression gland and aluminium lugs for 4X16 sq mm. of PVC insulated and PVC sheathed/XLPE aluminium conductor cable of 1.1KV grade as required.

Supplying and fixing of 4 way (4+12) Double Door surface/recess mounting vertical type, 415 volt, TPN MCB distribution board of sheet steel dust protected duly powder painted inclusive of 200Amp., tinned copper busbar, common neutral link, earth bar, din bar for mounting MCB's (But without MCB and incomer) as reuired. (Model should be got approved before installation)

Supplying and fixing 63A rating, four pole, (three phase and neutral), 415 volts, residual current circuit breaker (RCCB), having a sensitivity current 30 mA in the existing MCB DB complete with connections, testing and commissioning etc. as required.

Supplying and fixing 5 A to 32 A rating, 240/415 V, 10 kA, "C" curve, miniature circuit breaker suitable for inductive load of Single Pole in the existing MCB DB complete with connections, testing and commissioning etc. as required.

Supplying and fixing DP sheet steel enclosure on surface/ recess along with 25/32 A 240 V "C" curve DP MCB complete with connections, testing and commissioning etc. as required.

Providing and fixing 6SWG dia GI wire on surface or in recess for loop earthing along with existing surface/recessed conduit/submain wiring/cable etc as required.

Supplying and fixing 1 or 2 Module (75mmX75mm) modules, GI box alongwith modular base & cover plate for modular switches in recess etc. as required.

ADIT FABRICATIONS

Multiview Construction Company

J P Constructions