PROVN OF FOUR URINAL AND ONE WHB OF CENTRAL BATHROOM AT INT BRANCH AND COVERED SHED FROM INT BRANCH TO OPS BRANCH AT HQ CIF (R) PALMA GRN UNDER AGE(I) CIF (R) 2ND CALL 2nd CALL

Amount

Excavation in trenches in any type of soil n. exc 1.5m wide & n. exc 1.50m in depth for foundations for shafts, wells, cesspits, manholes, pier holes & getting out complete all as specified and directed

Material and labour for plain cement concrete 1:4:8 type D-2 (using 40 mm graded mechanically crushed stone aggregate), as in foundation filling and mass concrete, complete all as specified and directed.

M&L for providing reinforced cement concrete (design mix) M-25 (using 20mm graded stone aggregate) as in foundations, including rafts, footings, foundation beams; plinth beams; bases for columns, etc.; basement slabs, under-reamed piles and mass concrete complete all as specified and as directed

Removing excavated soil to a distance not exceeding 50 m and depositing where directed at a level not exceeding 1.5m above the starting point complete all as specified and directed.

Returning, Filling in including Spreading, Leveling, Watering and Well Ramming in layers not exc. 25 Cm thick in Soils, complete all as specified and as directed.

M&L for providing reinforced cement concrete (design mix) M-25 (using 20mm graded stone aggregate) as in column , pillars, piers,posts and struts complete all as specified and as directed

M & L brick work with subclass ‘B’ bricks, straight or curved on plan exc 6 m mean radius built in Cement mortar 1:6 etc, all as spcified and direcrted.

M & L for 40mm thick damp proof coarse in cement concrete (1:2:4) type B-0 (using 12.5 mm graded stone aggregate) using water proofing compound ,to horizontal or vertical surface including use of necessary form work , complete all as specified

M & L for providing reinforced cement concrete (design mix) M-25 (using 20mm graded stone aggregate) as Beams, cantilevers,bressummers, lintels over1.5m spancomplete all as specified and as directed

M&L for providing reinforced cement concrete (design mix) M-25 (using 20mm graded stone aggregate) slabs supported on walls,beams and columns in floors,roofs, landings, balconies,canopies, deck slabs and inshelves and the like complete all as specified and as directed

M & L Formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work; vertical or to batter flat for rough finished surfaces of concrete etc.

M & L Formwork to sides of pillars ,posts, struts, piers, columns and stanchion etc for rough finished surfaces of concrete etc.

M & L Formwork to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including supports, overhangs, etc. also splays between floors and beams flat for rough finished surfaces of concrete etc.

M & L Form work to soffits of suspended slabs such as roof slab, floor slab and similar work not exceeding 200mm thick for rough finished surfaces of concrete flat complete all as specified and directed..

M & L Form work to edges of RCC roof slab, floor slab and similar work not exceeding 200mm thick for rough finished surfaces of concrete flat complete all as specified and directed..

M&L mild steel TMT bars, 10 mm dia and over, cut to length, bent to shape required including cranking, binding spirally for hooping or column, hooking ends and binding with mild steel wire (annealed) not less than 0.9 mm dia or securing with clips, complete all as specified and directed.

Material and labour mild steel TMT bars, 6 to 8 mm dia , cut to length, bent to shape required including cranking, binding spirally for hooping or column, hooking ends and binding with mild steel wire (annealed) not less than 0.9 mm dia or securing with clips, complete all as specified and directed.

Mild steel TMT bars 5 mm dia and over up to and including 10 mm dia in stirrups, spacers and binders, cut to length, bent to shape required, including crancking, bending spirally for hooping for columns, hooking ends and binding with mild steel wire (annealed) not less than 0.90 MM dia or securing with clips all as specified and directed.

Rendering 15mm thick cement plaster on stone masonry surfaces or other than fair faces of brick work CM 1:4 finished even and smooth without using extra cement complete all as specified and directed.

M&L for preperation of new surfaces of walls and applying two coats of cement base paint over a coat of alkali resistant primer complete all as specified.

M&L for 10 mm thick rendering on fair faces of brick work in cement mortar 1:6 and finished even and smooth without using extra cement, complete all as specified.

Material and labour for three coat of white wash on newly plastered surfaces of wall including preparation of surfaces complete all as specified and directed

Material and Labour for 5mm thick cement plaster in CM (1:4) to ceiling surface and finished the surface even and smooth without using extra cement complete all as specified.

Material and labour for three coat of white wash on newly plastered surface of ceiling including preparation of ceiling surfaces complete all as specified and directed

Material & Labour for Non-skid coloured ceramic tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including cement screed bed 10mm thick in cement mortar (1:4) base, complete all as specified.

M&L for glazed ceramic coloured designer tiles 450 x 300x 7 mm thick as in Vertical surfaces set and jointed in neat cement slurry and jointed or coloured cement to match etc complete over 10 mm thick rendering in CM 1:3 all as specified and directed.

M&L for 25mm thick cement concrete type B-0, 1:2:4 (12.5mm graded stone aggregate) as in sub floor finished even and rough to receive the topping layer (w/o using extra cement) complete all as specified and directed.

M&L 50mm thick PCC (1:2:4)type B-1 (using 20mm graded coarse aggregate) over 75mm thick PCC (1:3:6)type C-2 (using 40mm graded coarse aggregate ) laid to an outward slope 1:12 as in plinth protection complete all as specified and directed.

Sand filling under floors or in foundation including watering and consolidation

Material and labour for plain cement concrete 1:5:10 type E-2 (using 40 mm graded aggregate), as in foundation filling and mass concrete, complete all as specified and directed.

Supply and fixing factory made PVC hollow door frame of size 50 mm x 47 mm with wall thickness of 5 mm made out of extended 5 mm rigid PVC foam sheet cut at corner and jointed with 02 Nos., 150 mm long brackets of size 15 mm x 15 mm mild steel square tubes 19 gauge including vertical door profiles reinforced with 19 mm x 19 mm steel square tube of 19 gauge (EPDM) rubber gasket weather seal provided through out the frame and fixing to wall with 65/100 mm long mild steel screws through the frame by using PVC fasteners (minimum of 04 Nos. of screws to be provided for each vertical number and minimum 02 Nos. for horizontal member), complete all as specified and directed.

Supply and fixing factory made 30 mm PVC rigid foam panel door shutter made from mild steel tubular frame of size 19 mm x 19 mm for stiles and 15 mm x 15 mm for top and bottom rails and covered with 5 mm thick head moulded PVC channel having width of 50 mm to form stiles and PVC street of width 75 mm to form rock rail, bottom rail and top rail or either side having panels inserted with 5 mm thick PVC sheet sealed with solvent cement adhesive to the stiles and rails with 5 mm x 25 mm PVC sheet beading on either side including three Nos. aluminium hinges for each door complete all as per manufacturer instructions complete all as specified and directed.

Supply & fixed aluminium anodized, barrel tower bolts of extruded section 200mm long ISI marked complete all as specified.

Supply & fixing 300 mm aluminium anodised sliding door bolts, ISI marked, with hasp, staple (bolt type) complete with clamps bolt not less than 16mm dia and fixing clips of sheet, cast or extruded section and fixing bolts an sliding bolt of extruded section or cast aluminium alloy, complete all as specified.

Supply & fixed mild steel butt hinges medium weight, cold rolled, 100 mm, ISI marked, complete all as specified.

Supply & fixed extruded aluminium alloy handles, fabricated type, anodized 150mm long, complete all as specified.

S&F Rotational moulded polyethelyne water storage tank HDPE three layered (cylindrical vertical with closed top hoisted fixed in position all as specified in SSR part-I, capacity of tank 500 ltr incl inlet and outlet connection 20mm dia and 15mm dia GI pipes medium grade ,complete all as specified.

S&F 20mm Ball brass valves,high pressure, with polythene float and flynut complete, screwed for iron pipe or brass ferrule complete all as specified.

Supply & fixed vitreous china wash hand basin white flat back of size 550x440mm including CI brackets including cutting for and pinning in ends of brackets or erecting stand including 32mm Waste coupling of PTMT(half or full threaded), complete all as specified.

S&F Viterious china Urinal,Half stall type, white(excluding flushing cistern,flush pipe) complete incl providing for fixing plugs,bedding urinals against wall in cement mortar 1:2,securing urinal to pulge with and including 60mm long brass screw,pointing around urinal back in cement, including urinal spreader etC, complete all as specified.

S & F PVC (SWR) junction single,(Single T) equal or unequal of radius 110mm bore, complete all as specified.

S & F 110 mm bore PVC ( SWR) pipes single socketed ,in any length with rubber ring joints, laid in trenches and floor, complete all as specified.

S & F PVC (SWR)P traps 110 mm bore, complete all as specified.

S & F PVC (SWR) S traps 110 mm bore, complete all as specified.

S & F PVC (SWR) bends of radius 110mm bore, complete all as specified.

S & F PVC (SWR) vent clow of radius 110mm bore, complete all as specified.

Material and Labour for cutting chases for concealed water tubing and making good, (cutting not exceeding 10 cm girth) in cement mortar (1:3), complete all as specified.

Supply and fixing steel water tubing of 15 mm bore, medium grade galvanized with provision of all new fittings as required, laids in floor, wall and on ceiling, complete all as specified and directed .

Supply and fixing steel water tubing of 20 mm bore, medium grade galvanized with provision of all new fittings as required, laids in floor, wall and on ceiling, complete all as specified and directed .

S&F bib tap cast copper alloy, with cruntch and butterfly handle screwed down , chromium plated, ISI marked, screwed down suitable for 15mm bore pipe or union, complete all as specified.

Supply and fixed stop valves, cast copper alloy ISI marked screwed down, high pressure, with crutch or butter fly handle screwed both ends for iron pipe or for unions, suitable for 20 mm bore tubes, complete all as specified.

Supply and fixed stop valves, cast copper alloy ISI marked screwed down, high pressure, with crutch or butter fly handle screwed both ends for iron pipe or for unions, suitable for 15 mm bore tubes, complete all as specified.

Supply and fixing angle valve, 15mm dia chromium plated, cast copper alloy, screwed down, high pressure with capstain head, heavy with adjustable wall flange, complete all as specified.

Supply and fixing PVC connection 15mm size with brass nuts of length 450mm complete all as specified.

Supply and fixing for CP grating 100 mm dia with or with out hole complete all as specified.

S&F for centre hole basin/ Wall mixture valve, cast copper alloy fancy type 15mm brass chromium plated mixer (central hole basin mixer w/o pop up waste system) for mixing hot & cold water screwed down for iron pipe, complete all as specified.

Supply and fixing for aluminium powder coated ventilator having fixed glass with aluminium section having section 50.80 mm x 25.40 mm (weight 1.137 kg/m) glazing clear section (weight 0.109 kg/m) with plain anodized including supply and fixing of 5mm thick frosted glass making frame and glass water tightening making it good and Aluminium grill 6 mm dia design No DG-102 make DEDO grill or design No A-103 make aluminium grill fixed to 50 x 20 x 1.5mm thick etc. Complete all as specified and directed by Engineer-In-Charge.

S&F aluminium anodised towel rail 20mm dia D type, 60CM long including fitting complete all as specified.

M&L for rendering 10mm thick in CM (1:3) on faces of concrete surface of slab with WPC complete all as specified.

M&L APP based polymeric membrane 5 layered of weighing 3kg/sqm and minimum 3mm thick reinforced with polyster non wove fabric (wt. not less than 150 gms/sqm) over a coat of hot blown bitumen 85/25 penitration [email protected] Kg/Sqm primed on bitumen primer @0.4Kg/Sqm complete followed by another coat of semi hot blown bitumen 85/25 grade @1.2 kg/Sqm over the membrane and a coat of aluminium pain tover it, all as specified.

Surface excavation in soft/loose soil n exc 30 cm deep and averaging 15 cm deep and getting out hard and dense soil complete all as specified .

M&L for 100 mm PCC(1:5:10) type C2 using 40 mm graded aggregate used as in Sub base Floor/ Pavings and finishing cement concrete surface with out using extra cement, complete all as specified .

M & L Chequered cement concrete tiles pre polished lacuqer and glossy finish 30cmx30cmx22-25mm thick over 20mm thick screed bed in CM (1:4) set ,jointed and pointed in neat cement slurry with grey cement and pigment in floors.complete all as specified and directed.

M&L for concrete bed (1:3:6) Type C2 to 150 mm drain pipe including packing under and haunching against side of pipes after they are laid and tested all as specified.

S & F 150 mm bore PVC ( SWR) pipes single socketed ,in any length with rubber ring joints, laid in trenches and floor etc.

M&L for Cement concrete (1:2:4) Type B1 in lintels upto 1.5m clear span, cills, steps; seismic and other similar bands, plinth courses, string courses, lacing courses, parapets and railings upto 60 cm in height, copings, kneelers, apex stones, bed plates, kerbs , water troughs and the like including weathering, slightly rounded or chamfered angles and throating, complete all as specified and directed .

M&L PCC 1:3:6 type C-2 (20 mm graded aggregate) in in surface channel and drain etc including necessary form work etc, complete all as spcified and diracted.

Extra for forming fair finished drain or channel 30 cm inner girth in cement concrete , using extra cement, including forms, moulds, mitred/ stopped ends etc. all as specified.

Construction of Soakage well of size 1.2m dia and 3.0m effective depth in excavation in any type of soil foundation in PCC 1:3:6 , walls of honey combed and solid brick work in CM 1:4, RCC M-25/SFRC cover slab filling with bats as shown in drg No TD CE/TD-1202/2003 sheet No 1/2 and 2/2 dt 09.10.2003, complete all as specified in drg, complete all as specified and directed. Note : Rate quoted shall deemed inclusive of dewatering during construction if met with.

M&L for 100 mm thick plain cement concrete, 1:4:8, type D-2 ( using 40 mm graded crushed stone aggregate ) as in sub base and paving, complete all as specified and as directed.

75mm bore PVC (SWR) pipes single socketed, in any length with rubber ring joints, laid in trenches or in floors complete all as specified and directed by Engineer-in-charge.

Excavation in post holes (or similar holes) each not exceeding 0.5 Cum, getting out, returning, filling and ramming earth or broken rubble mixed with earth around in layers not exceeding 25 cm and removing surplus soil not exc 50 Mtr and making good surface (in soft/loose soil), complete, all as specified.

Steel work in tubular trusses including special shaped washer etc. complete using ERW or induction butt welded tubes conforming to I.S. 1161- 1979 grade St.-240, complete all as specified and as directed..

S & F mild steel screw bolts (machine made) with hexagonal or square heads at one end and screwed the other, or screwed both ends, each screwed end to be fitted with washers and one hexagonal or square nut length 20cm long & dia 20mm, complete all as specified and directed.

S&F pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550Mpa as in roof covering/cladding to wall, fixed with self tapping screws. Sheet colour approved by Engineer-in-Charge complete all as specified and directed.

S&F pre-painted galvalume aluminium zinc coating GI based plain steel sheet 0.50mm thick of any colour having tensile strength of 550Mpa as in roof covering/cladding/ridges to wall, fixed with self tapping screws complete all as specified and directed.

M&L for preparation of new steel surfaces of any description, over 10cm in width or girth, not otherwise described and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and directed by engr-in-charge.

Deduction to be made from BOQ for schedule of credit (Sch 'A' Part - II) Amount of ₹ Nil during AOC Note:- Tenderers shall not quote for this Schedule

M/S RAHUL GUPTA (BID ID -3415429)

NATIONAL TRADING COMPANY (BID ID -3433776)