PROVN OF ADDITIONAL BATH AND SANITARY FITTINGS FOR CERTAIN SINGLE ACCN IMPROVEMENT WORKS FOR WATER SUPPLY AT TRG AREA AND TOILETS OF TRAINEES AT SOUTH CAMP ATS BELGAVI

Amount

Demolition of cement concrete (unreinforced) in ground floors and pavings n exc 15 cm thickness (below or above ground level) all as specified

Demolition of brickwork or stone/boulder masonary, build in cement mortar or cement lime mortar including all quoins, arches, pillars, etc, and removing all as specified and directed.

Excavation in trenches n exc 1.5 m wide and n exc 1.5 m depth in hard / dense soil for foundation etc or for shaft, wells, manholes, pier holes etc n exc 10 Sqm on plan and not exc 1.5 m in depth and getting out complete all as specified and directed.

Excavation in trenches n exc 1.5 m wide and n exc 1.5 m depth in soft / loose soil for laying G I pipes in trenches not exc 1.5 m in depth and getting out complete all as specified and directed.

Surface excavation n. exc (not exceeding) 30cm deep and averaging 15cm deep and getting out in hard/dense soil complete all as specified and directed.

Returning filling in including spreading levelling and well ramming in layers not exc 25 cm in hard soil all as specified and directed.

Removing excavated material not exc 50 m and depositing where directed at a level not exc 1.5 m above the starting point all as specified and directed.

Material and labour for broken stone or boulders hardcore gauge n exc 63 mm, deposited spread and levelled in layers n exc 15 cm thick, watered and rammed to true surface complete all as specified and directed.

Material and labour for PCC (1:4:8) type D-2 using 40 mm graded stone aggregate as in foundation filling and mass concrete all as specified and as directed

M & L for pre cast cement concrete block masonry type C1 1:3:6 (20 mm graded agrregate) solid blocks exc 10cm in width having minimum compressive strength of 50 kg/sq cm as per IS 2185 (Part I) 2005 and set in cement mortar 1:4 complete all as specified.

Material and labour for providing cement concrete type B-1 1:2:4 (20mm graded aggregate) as in intels upto 1.5m clear span, cills, steps; seismic and other similar bands, plinth courses, string courses, lacing courses, parapets and railings upto 60 cm in height, copings, kneelers, apex stones, bed plates, kerbs, water troughs and the like including weathering, slightly rounded or chamfered angles and throating, as directed & including necessary form work. Exposed surface of concrete shall be finished even and smooth without using extra cement all as specified and directed.

Material and labour for Cement concrete 1:2:4, type B-1 (using 20mm gradecrushed stone aggrigate) as in benching and forming channel inside manholes for section of pipe 100mm, 150mm or 200mm including finished smooth and even using extra cement all as specified and directed.

Material and labour for providing precast cement concrete louvres and jallies set in CM 1:4 , 25mm thick type C0 1:3:6 (12.5mm graded stone aggregate) (measured solid), including all mouldings but excluding frame complete all as specified and directed.

Material and labour for Precast cement concrete 1:2:4 type B1 (using 20mm graded stone aggrigate) for cover Slabs (for man holes etc) setting in cement mortar(1:4) as specified and directed

Material and labour for forming jambs, etc; to opening including cutting, toothing and properly bonding into old work, also facing, jointing and pointing to match existing work, in cement mortar 1:4 complete as specified and directed

Material and labour for Brickwork with sub-class 'B' bricks, straight or curved on plan to any radius in half brick thick walls built in CM 1:4 complete all as specified and directed.

Material and labour for reinforced cement concrete (nominal mix) type B1 1:2:4 (20 mm graded aggregate) in slabs supported on walls, beams and columns in floors, roofs, landings, balconies, deck slabs and in shelves and the like bands in walls complete all as specified and directed.

Use and waste formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceedings 200mm thick (Horizontal or sloping) rough finished surfaces of concrete flat complete all as specified and directed.

Use and waste formwork to edges of concrete flats, breaks in floors, openings in concrete walls, floors and roofs and sides of RCC/PCC bands in walls, horizontal or sloping and similar work complete all as specified and directed.

Taking down chowkhats or frame n. exc 1.5 sqm with shuttter ( without taking off shutter from the frames) complete all as specified and directed

Taking down chowkhats or frame exc 1.5 sqm but n exc 4 sq. m each ( without taking off shutter from the frames) complete all as specified and directed

Supply and fix factory made solid PVC door frame of size 50mmx47mm made out of 5mm plain colour PVC sheet reinforced with ms square tube suppling and fixing in opening as per specification and drawing all as specified and directed.

Supply and fix factory made solid pane PVC moulded door shutter 28 to 30 mm thick (stiles) with 2, 4 or 6 raised panel design with 2 mm thick moulded PVC sheet on the front face and 2 mm thick plain colour PVC sheet on back face as per specification and drawing with particle board core all as specified and directed.

Supply and fix PVC ventilators with frame work made of multi chamber hollow PVC section DWUF 405 (40x46mm). The glass (3mm thick pin headed) is fixed to the frame in the lower section using extruded PVC section having a dimension of 9mm x 14.5mm (GL-19 SINTEX PVC section) with EPDM gasket (SPL-003) for both the PVC sections. SINTEX make ventilator's centre mullion made up of multi chamber hollow PVC section DWUF-406 (63.5mm x 40mm) with EPDM gasket is used. GL-19 is fixed to the 3 sides of DWUF-405 and to one side of DWUF 406 (63.5 x 40mm) above the centre mullion. Glass panels with aluminium lower set is fixed to the frame DWUF-405 on the top of the ventilator for the glass. DWUF 405 and DWUF 406 corners shall be metre cut and welded, jointed with 12mm MS rods (guard bars) including glass and stainless steel wire mesh complete all as specified and directed.

Supply and fix 300 mm Aluminium alloy ,anodised sliding door bolt with hasp and stapple all as specified and directed.

Supply and fix 200 mm long aluminium anodised barrel tower bolt all as specified and directed.

Supply and fix 150 mm long aluminium anodised handle cast type all as specified and directed.

Supply and fix 100 mm long stainless steel butt hinges all as specified and directed.

Supply and fix in repairs stainless steel wire cloth 0.36 mm nominal dia of wire and average width of aperture 1.40 mm and fixed with stainless steel wire staples or steel screws complete all as specified and directed.

Supply and fix Bands, straps, supports or stays for rainwater, ventilating pipes, including bolts, if required; hooks (stay), heavy, for large gates; hook and pintle hinges; hasps and staples; chains; hand made sliding bolts; clamps; hold fasts; wall ties; hooks for hanging fans; plain angle cleats; knee piece inserts; two way and three way straps, plate washers and similar ariticles conforming to Fe 250, Gde-E-165 complete all as spfd.

Supply and fix steel work in tubular posts, purlins, rafters, medium weight including special shaped washer etc complete using ERW or induction butt welded tubes conforming to IS 1161-1979 grade St -240 complete all as specified and as directed.

Supply and fix framed work such as grills, gratings, etc, with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of watertanks and similar work conforming to Fe. 290. Gde-E-165 complete all as specified and directed.

Supply and fix ISMB joist, channel medium grade fixed independently, without connecting plates etc Fe-290 (Gde E-165) complete all as specified and directed.

Material and labour for mild steel TMT bars of 10 mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed.

Material and labour for mild steel TMT bars of 6mm to 8mm, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed.

Dismantling wall floor hearth tiling including cement mortar bedding (but not backing) and removing unserviceable material as directed.

Material and labour for 75mm thick PCC 1:3:6 type C2 using 40 mm stone agg as in plinth protection finished even and fair w/o using extra cement all as specified and directed.

Material and labour for 75mm thick cement concrete type D-2, 1:4:8 (40mm graded aggregate) complete as in sub base all as specified and directed.

Material and labour for 100mm thick cement concrete type B-1, 1:2:4 (20mm graded aggregate) finishing cement concrete surface even and smooth without using extra cement complete all as specified and directed.

Forming 12mm thick expansion joints filled with pre-formed bituminous filler and top 30mm primed and sealed with sealing compound, Grade 'A' as in 75mm thick plinth protection complete all as specified and directed.

Forming 12mm thick expansion joints filled with pre-formed bituminous filler and top 30mm primed and sealed with sealing compound, Grade 'A' as in 100 mm thick cement concrete complete all as specified and directed.

Material and labour for 50mm thick 1:4:8 type D2 using 40mm graded stone aggregate as in sub base of flooring complete all as specified and directed

Material and labour for Coloured glazed ceramic tiles economy finish Gde B-II (b) quality of size 300 x 450 x 7 mm thick with rectified edges as in vertical surfaces set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles over and incl 10 cm thick backing with cm 1:4. all as specified and directed.

Material and labour for dark coloured Non skid coloured tiles superior finish grade B-1 quality 7 to 8 mm thick(square/ rectangular) area of each tiles exceeding 0.11 sqm but not exc 0.18 sqm in floor with rectified edges ( joint free) etc set and jointed in neat cement slury over cement screed 15 mm thick 1:6 all as specified and directed.

Material and labour for 15 mm thick cement morter plaster 1:6 for wall finished even & smooth without using exter cement all as specified and directed.

Material and labour for 15 mm thick cement plaster in CM 1:4 for wall finished even & smooth without using exter cement all as specified and directed.

Hacing out old broken glass (any thickness, size, quality or description) from metal frame including punching or drilling out old glazing pins /spring clips and providing and fixing new ones complete all as specified and directed.

Supply and fix 4 mm thick figured glass pin head type and glazing with oil putty in square n. exc 0.5 sqm in each pane complete all as specified and directed.

Material and labour for three coats of white wash on walls, pillasters, cornices, etc., on newly plastered walls including preparation of surfaces all as specified and as directed.

Material and labour for preparation of newly plastered surfaces and applying two coat of oil bound distemper over a coat of primer complete all as specified and directed.

Material and labour for preparation of newly plastered surfaces and applying two coats cement based paint over a coat of primer on walls, pillasters, cornices, etc all as specified and as directed.

Material and labour for preparation of new plastered surfaces of walls and applying two coats of anti fungal paint over a coat of primer all as per manufacturers instruction complete all as specified and directed.

Material and labour for preparation of new steel surfaces of any discription not exc 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of primer complete all as specified and directed.

Material and labour for preparation of new steel surfaces of any discription over 10 cm width or girth, not otherwise described and applying two coats of synthetic enamel paint over a priming coat of red oxide complete all as specified and directed.

Supply and laying of CPVC pipes of 50 mm outer dia SDR 11 and plain CPVC SDR 11 fittings on wall /ceiling or laying in floors including all fittings complete all as specified and directed

Supply and laying of CPVC pipes of 25 mm outer dia SDR 11 and plain CPVC SDR 11 fittings on wall /ceiling or laying in floors including all fittings complete all as specified and directed

Supply and laying of CPVC pipes of 20 mm outer dia SDR 11 and plain CPVC SDR 11 fittings on wall /ceiling or laying in floors including all fittings complete all as specified and directed

Supply and laying of CPVC pipes of 16 mm outer dia SDR 11 and plain CPVC SDR 11 fittings on wall /ceiling or laying in floors including all fittings complete all as specified and directed

Supply and fix 15mm bib taps fancy type chromium plated round handle, screwed down, screwed for iron pipe and fixed in repair all as specified and directed

Supply and fix in repair 15mm stop valves cast copper alloy fancy type, chromium plated, screwed down, high pressure, with crutch or round handle screwed bolts ends for iron pipe or for unions and fixed all as specified and directed

Supply and fix Pillar taps, cast copper alloy, with capstan heads,chromium plated,screwed down high pressure, with or without lettered Hot' or 'Cold' with long screwed shanks and fly-nuts,screwed for iron pipe and fixed all as specified and directed '

Supply and fix swivel shower of stainless steel for fixing with 15 mm pipe all as specified and directed.

Supply and fix tubular brass chromium plated Towel rail 20 mm dia D type 60 cm long between flanges all as specified and directed

Material and labour for Salt glazed stone ware pipe laid in trenches and jointed with cement nominal dia of pipe.150 mm. all as specified and directed.

Material and labour for Cement concrete 1:4:8, type D-2 (using 40mm graded crushed stone aggrigate) as in bed to drain pipe including packing under and haunching against the sides of pipes after they are laid and tested for 150 mm bore pipe. all as specified and directed.

Supply and fix 75 mm dia PVC (SWR) pipes single socketed in any length with rubber ring joints, fixed in wall/ floor with necessary clamping where required all as specified and directed.

Supply and fix 110 mm dia PVC (SWR) pipes single socketed in any length with rubber ring joints, fixed in wall/ floor with necessary clamping where required all as specified and directed.

Supply and fix (SWR) floor trap, plain with grating including jointing with solvent cement 75 mm dia inclduing fixing to existing pipe properly with solvent all as specified and directed

Supply and fix PVC bends for 75 mm bore pipe with access door all as specified and directed.

Supply and fix PVC bends for 110 mm bore pipe all as specified and directed.

Supply and fix CP soap dish fixed to plugs with chromium plated brass screws all as specified and directed.

Supply and fix vitreous china wash down water closet pan pedestal pattern white (excluding flushing cistern and flush pipe ) including all accessoreis i.e seat cover and etc. complete all as specified and directed.

Supply and fix PVC valve less syphonic action type low level flushing cistern 10 Ltr capacity including flange valve handle, Bracket, PVC flush down pipe length upto 1.3 m hight dia as required with bend complete all as specified and directed.

Supply and fix vitrious china wash basin white oval type of size 450X300 mm including, waste coupling , pipe and cutting for and pinning in ends of brackets or erecting stand brackets complete all as specified and directed.

Supply and fix PVC connection 15mm size with PTMT nuts of length 450mm complete all as specified and directed.

Supply and fix Stainless steel Health faucet Abs body with 1 meter long flex tube in chrome finish and wall hook complete and all as specified.

Supply and fix rotational moulded polyethylene water storage tanks of 2000 ltrs capacity (cylindrical vertical with closed top) hoiseted and fixed in position all as specified and directed in SSR part I inlcuding fixing of PTMT ball valve epoxy coated aluminium rod and high density plastic ball of 20 mm dia or equivalent as per site condition.

Supply and fix stop valves 20 mm bore, cast copper alloy, screw down, high pressure, with crutch or butterfly handle, screwed for iron pipe or for union complete all as specified and as directed .

Supply and fix 20mm ball brass valve (gate valve), high pressure, with polythene float and flynut complete, screwed for iron / CPVC pipe or brass ferrule and fixed complete all as specified and as directed.

Supply and lay 25 mm bore pipe galvanized medium grade including fittings fixed to wall / ceiling or laid in floors complete all as specified and directed.

Supply and fix gun metal,globe or gate valves with iron wheel head,screwed both ends for GI pie and fix, 25 mm dia pipe complete all as specified and directed.

Cutting the existing GI pipe of 100 mm for connection of 25 mm dia GI pipe complete all as specified and directed. Note- Quoted rate shall include the threading & item required for alterations or additions like Tee,ferruls etc

Cutting chases, pinning in, making good to facing for where required and pointing in cement morter 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels etc and cutting chases for concealed water tubing or concealed conduit wiring, etc and making good, cutting not exceeding 10 cn girth all as specified and directed.

Material and Labour for point wiring with PVC unsheathed multi standard 1.5 Sqmm FRLS copper Cable for one light point controlled by one way switch, and wire to be drawn in and including PVC casing capping 20/25 mm width complete with all accessories including MS sheet metal 1.2mm thick switch board or PVC rectangular switch board of suitable size to be fixed on wall respectively including white washing/colour washing/distembering to match the disturbed surfaces including PVC unsheathed multi standard 1.5 Sqmm FRLS copper Cable as earth continuvity connected with common earth dolly complete all as directed by Eng -in Charge

One light point controlled by one, one way switch 5 Amp complete

One 3 pin socket outlet 5 amp independent

Sypply and fix complete for switch piano flush button single pole one way 5 Amp 240 V all as specified and directed.

Sypply and fix switch socket combination 2 in 1,3 pin 5 Amp flush type 240 volts complete all as specified and directed.

Sypply and fix ceiling rose surface backelite three terminal 240 volts complete all as specified and directed.

Supply and fix REGAL Batten for LED tube with single LED Lamp 1x 20 w, Ultra bright glass LED Tubelight with very high efficacy suited for installation in T5/T8 fitting with lamp holders etc. complete with all accessories internally pre-wired and including connecting up with twin core twisted flexible copper conductor cable with suitable size all as directed. Make & Model No for Batten :Crompton compact industrial LED Batten for fixing LED Tube Cat No DIJB12LTB-20 and LED Lamp Crompton Cat No LGT8-20-865-2 or equivellent make of Havells / Philips / Bajaj / C&S

Material and labour for sub main wiring with two single core stranded copper conductor unsheathed PVC insulated FRLS cable 1100V grade with 6 sq mm drawn through suitable size of non-metallic PVC rigid conduit/casing caping with one run 6 sqmm copper conductor FRLS cable as earth conductor and conduit accessories fixed up in surface/ recessed as required, including connecting up complete all as specified and directed. NOTE ;- Two runs of 6 sq mm cable and one run of 6 sq mm earth continuity copper conductor and one run of PVC conduit / casing caping shall be measured as one unit

Sypply and fix sheet metal enclosure factory made double door for DB 240 volts with 200 Amps rated bus bar SPN 4 Way complete all as specified and as directed .

Sypply and fix MCB SPN 32 Amps 240 volts, 50 Hz AC supply complete all as specified and directed.

Supply and fix MCB SP 06 to 32 Amps 240 volts, 50 Hz AC supply all as specified and directed.

Sypply and fix 1x9 w bulk head luminaries, with lamp holders & LED lamp etc.complete with all accessories and including connecting up with twin core twisted flexible copper conductor cable with suitable size of 230V, 50 HZ all as specified and directed.

Material and labour for Earthing complete with galvanised mild steel earth plate electrode of size 600 x 600 x 6mm thick burried directly in ground earth (in vertical) earth pit not less than 2.25 mtr deep below normal ground level with top edge of the earth plate not less than 1.5 mtr below ground level connected to galvanised iron or earth lead wire 4mm dia (8 SWG) by means of nut, bolt, check nuts and washer of galvanised ironl including PCC pit in PCC 1:2:4 type B-1 pre-cast RCC cover slab using reinfocement with XPM weighing not less than 1.87 kg/Sqm with suitable handle made of 12mm round bar, including necessary excavation and earth work in any type of soil, 20mm dia medium grade galvanised steel tube flor watering with one end fixed with cast iron funnel and wire mesh 15mm dia bore light grade galvanised steel tubing upto 5 m length for drawing earth lead wire protection, common salt, charcoal, etc complete all as shown in electrical plate No 5 of SSR Part-I and testing on completion.

DHAIRYASIL RAMAKANT DESAI

M/S ADITYA CONSTRUCTIONS

LAKSHMI DEVELOPERS

DHANSHRI ENTERPRISES

M/S MAHADEV M PATIL

PURVIK CONSTRUCTIONS