Nagercoil Corporation Providing sheet shed with Purlin and aluminium partition work at Vadasery PHC

Amount

Providing sheet shed with Purlin and aluminium partition work

Earth work excavation and depositing on bank with initial lead of 10metres and lift of 2metres in all kinds of soil except mediumrock, dense medium rock and hard rock requiring blasting including refilling the sides of foundation with excavated earth in layers of 15cm thick, watering and consolidation and depositing the surplus earth with in the compound in places as shown by the departmental officers with initial lead and lift. cleaning,levelling the site etc,. complete complying with standard specifications.(TNBP No.20B)

Conveyance of excavated surplus earth to low lying areas through tipper lorries upto 2km lead including,labour charges for loading,transporting and unloading in low lying areas shown by the departmental officers

3" GI pipe

3/4" PVC pipe

Wirinng with 2x1.5sq.mm (22/0.3) PVC insulated SC. unsheathed Cu.Conductor of 1100V garade in suitable PVC rigid pipe on wall and ceiling with PVC accessories and with TW switch box and 5A FT switch inflush with wall covered with hylum sheet of 3mm thick with painting of suitable colour for open PVC light/fan point (for electronic regulator) (5 points per coil)(SD 22)

Wirinng with 2x1.5sq.mm (22/0.3) PVC insulated SC. unsheathed Cu.Conductor of 1100V garade in suitable PVC rigid pipe on wall and ceiling with PVC accessories with 150x100x113mm TW switch box for 5A 3 pin non inter locking wall socket with 5A Flush type switch with painting of suitable colour with continuous earth wire connection of 14 SWG TC wire for open PVC Plug point. (SD36)

Supply and fixing of 1200mm (48") sweep AC ceiling fan complete with stepped electronic 300W regulator, with 1 metre down rod with fan clamp with side plates and cross arm of size 450mm(18")(SD 106)

Supplying fabricating and fixing in position of aluminium anodised ntural colour matt finish door half glazed and half PLB board / fully 12mm thick PLD board /fully 5.5mm thick glazed door using rectamgular Alu.Lox section of following sizes for frame and shutter with necessary accessories such as rubber beading,aluminium clips ,best double action floor springs / door closer ,handles locks and glass incuding all materials,labour and power consumption charges columns , booms , or masonry wherever with power drill to the extent required and made good to the original conditions after fixing etc.complete. The aluminium surface is to be anodised with matt finish under electrically controllee condition in accordance with SI specification 1000/1902 of andic film thickness of not less than 15 microns (fifteen) for all sections. All the materials should be got approved by the Engineer - in - charge before fixing in positioon as directed

Supplying and fabricating and fixing in position of aluminum anodised natural colour matt finish partition fixed glass for 1/2 portion and 1/2 portion with prelaminated MDF board. The frame using rect angular bo;x section 101.60x64.65x3.18mm @ 2.399kg/m inner vertical and inner horizantal and with neccessary; accessories such as reubber beadings furniture fittings ilncluding cost of materials lebour and power consumption cherges required for febrication including necessar clippilngs, dismantlling and making necessary holes in RCCcolumns beams sherever necessary with the same drill to the original all aluminlum sections are powder coated with approved colour as directed by the departmental officer etc., complete.

Woodern Board

Supply and fixing of precoated zine iron colour sheet for vertical cladding with necessary vertical supports using section 66x33x2.90mm of requred length connected with column by using base plats with bolt & nuts and fixing in rigid mannar is a horizontal rdirections all the member should be applied with one coat red oxide primer with enamel paint. The rate included , loading, unloading, transportation, material charges, labour cahrges for welding , cutting charges and as directed by the departmental officers

Supplying, fabricating, erecting structural steel work for roofing welded or bolted type using MS channels, angles, plates and round bars etc. conforming to IS specification including primer coating and enamal painting as per Design given by the departmental officers etc, complete as per standard specification

S.CHELLAM WORKS CONTRACTOR

Homage Infrastructure Services