Installation Solar Powered Micro Irrigation Scheme in the command area of outlet RD. 39700TR Gagsina Minor Village Bansa and Bhambredhi District Karnal

Amount

Works Details

Brick work with common burnt clay non-modular bricks of class designation 10.5 in foundation and plinth in : Cement mortar 1:4 (1 cement: 4 coarse sand) (New HSR Item No 7.21.1)

12 mm cement plaster of mix 1 :4 (1 cement: 4 fine sand) (HSR Item No 11.5.3)

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work below plinth level and up to Floor IV level: 1:3:6 (1 Cement : 3 coarse sand (zone-Ill) : 6 graded cum stone aggregate 20 mm nominal size) (New HSR Item No 6.1.4)

Providing and fixing of three phase 50Hz ±3% rated motor frequency, 415V ± 3% rated motor voltage, with constant motor flux control, (Submersible motors shall conform to all the requirements of IS 9283) Solar A.C. Agricultural Pumps alongwith Universal Solar Pump Controller (USPC) all external part of motor used in open well submersible pump having casing of Alloy steel confirming to IS 3444 including fixing PVC insulated polymer sheathed 3 core flat type cabling in conduit, required from solar plant to solar pump through control room required to connect, including cost of and as per IS code 14220-2018 including third party inspection.Average discharge 13 LPS / Head 52 meter / minimum / minimum output rating of 15 KW duly installed on the suitable foundation. Actual pump set's parameters will be finalized after approval of design and drawing. Solar Pumping Sets should be of the make: KSB / Shakti/ Kirloskar /CRI/Lubi/ Crompton/ WPIL, (NS Item) @ Rs 11002.53/- per HP Quantities are total sum of varrious pumps capacity in HP may varry as per design requirement for site. (NS Item)

Providing, laying, aligning, and jointing with butt fusion welding techniques (IS 7634 (Part 2) : 2012) at all level/ depths ISI marked HDPE pipe, PE-80 grade and PN 6 per design for portable water supply as per IS 4984-2016 (amended up to date) in trenches in complete, including cost of PE Specials, labour, sectional hydro testing (including the cost and conveyance of water to site for testing) and commissioning as per Technical Specifications and as per direction of Engineer including cost of third party inspection (Make Duraline,Reliance,Jain Irrigation,Nimbus,Finolex,Hasti,or equivalent)(NS Item) PE 80 PN 6 pipe,SDR 17,110 mm dia

PE 80 PN 6 pipe,SDR 17,140 mm dia

PE 80 PN 6 pipe,SDR 17,160 mm dia

Supply and installation of filter Hydro cyclone/ Sand separator 40 cum/hr(hot dip galvanized),flange connection with GI fittings, with flush valve, SS clamp, BSP thread cone shall comply IS 554, O'ring, with SS lock pin and collector tank as per IS 14743 as per latest amendment with all accessories(HSR item no 26.73.9)

Supply and installation of filter Sand/Media filter 40 cum/hr, with back wash and bypass assembly made in mild steel body as per IS 14606 as per latest amendment with all accessories and shall be provided with measuring points at inlet and outlet for pressure measurements and with backup strainer filter and all flanges should be of steel pipe confirming to IS 6392. (New HSR Item No-26.73.2)

Supply and installation of Strainer ilter Disc filter 50 cum/hr, with flush valve size 38mm inlet with disc clean element strong precision engineered and radially grooved disc to provide three dimensional filter,strainer element shall be made of stainless steel as per IS 12785 with latest amendment with all accessories.Housing made of mild steel shall be hot dip galvanized as per IS 4736.(New HSR Item No 26.73.6)

Providing & fixing Tank Type (Make of Metal) Fertilizer and Chemical Injector System confirming to IS 14483 (Part 3) of 2018 for demonstration & guiding the farmers regarding fertilization & chemicalisation of system. (rates include ventury with manifold 1.0"=1300 and 60 liter fertilizer tank= 4400 ) rate approved by Worthy Administrator, MICADA, Haryana

Excavating trenches of required width for pipes, cables, etc including excavation for sockets, and dressing of sides, ramming of bottoms, depth up to 1.5 m, including getting out the excavated soil, and then returning the soil as required, in layers not exceeding 20 cm in depth, including consolidating deposited layer by ramming, watering, etc. and disposing of surplus excavated soil as directed, within a lead of 50 m: All kinds of soil Pipes, cables etc. exceeding 80 mm metre dia. but not exceeding 300 mm dia (New HSR Item No-4.16.1.2)

Horizontal directional drilling with micro tunnelling methods for pipe laying under pacca rasta /road crossing(N.S. Item)

Providing and lowering of PE PN-10 floater to float the submersible open well pump/motor (NS item)

Galvanized steel chain link both end twisted fence fabric with opening size 7.5x7.5 cm & 3.15 mm dia wire 2.2 meter ht of mesh,with 2.8 metre ht of MS Angle 50x50x5 mm supports fixing at the spacing of 3 metre centre to centre,supports with of MS Flat 35x5 mm. The MS angle supports shall be anchored in cement concrete (1:3:6) blocks 45x45x60 cm additional razor barbed wire fencing shall be provided at the top of mesh fencing including gate @2000/- per metre(NS)

Supply Installation testing commissioning of Solar Photovoltaic Stand alone Plant conforming to MNRE specifications as amended, consisting of Mono Crystalline silicon solar cells, necessary protections, earthing, mounted on Aluminum/GI structure of suitable strength. Including lightning and surge voltage protection, Fixing of Array junction box & Main junction box with IP 65 protection and termination arrangement for incoming and outgoing cable along with glands, lugs and other accessories etc. as required, built in metering system to moniter plant performance (Amp-meter, Volt-meter, Frequency meter, Energy meter, Watt-meter, and other instrument/equipment as required) Note:- PV modules used must qualify to the latest edition of IEC PV module qualification test or equivalent BIS standards Mono Crystalline Silicon Solar Cell Modules IEC 61215/IS14286. In addition, the modules must conform to IEC 61730 Part-1- requirements for construction & Part 2 – requirements for testing, for safety qualification or equivalent IS and be mounted on fixed Aluminum/GI structure of adequate strength and design as per IEC/IS specification. Including field-based electroluminescence (EL) study be performed after receiving the modules at site and after installation. Module mounting structure (MMS) design and drawing shall be duly vetted from government institute Including third party inspection Actual parameters/capacity will be finalized after approval of design and drawing. (N.S. Item)

Supply and erection of Hot Dip Galvanized octagonal pole of 3mm thickness, with 14 watt LED light, base plate including cost of nut and bolts , earthing studs, Integral Cable termination arrangement 5 mm thick Bakelite base plate on suitable welded MS/GI bracket 32 A four way connector 2 no 1 O A SP MCB, end cover and all accessories as supplied by the manufacture including Providing RCC foundation of M25 grade (1 Cement:1 Stone aggregate: 2 Coarse sand) i/c excavation, steel reinforcement (Fe 500) @80 kg/cum of concrete contents, concrete cover 50mm, anchor bolts etc. over a bed of PCC 1 :5: 1 O of required dimensions for octagonal poles of various heights as per following specifications complete in all respects and as per directions of Engineer-in-charge 5 Metre Long pole with top dia 65 mm and bottom dia 130mm each 11944 with base plate of size 250 x 250 x 16 mm HSR item No 24.4.8.3

Hydrant assembly for nakka in field including, Tee, riser pipe, butterfly valve, flanges and labour for fixing butterfly valve should be as per IS 13095-2020(Rates are as per analysis including HSR item 25.3.6)

Supply and installation of 50mm i/d hydraulic pressure relief valve of polemeride with accessories for pressure regulation of irrigation system as per B IS standard.(New HSR Item No 26.73.10)

Providing and fixing C.I. double acting air valve of approved quality with bolts, nuts, rubber insertions etc. complete (The tail pieces, tapers etc if required will be paid separately) : 50 mm dia fixing in field Rates including service shaddel,ASTM pipe,coupler and ARV(to be fixed in field)including cost of isolator( New HSR item No. 22.185.1)

Providing, fixing,testing & commissioning of pressure gauge 2" dial with Glycerin filled (NS item)

Providing and fixing C.I. double acting air valve of approved quality with bolts, nuts, rubber insertions etc. complete (The tail pieces, tapers etc if required will be paid separately) : 80 mm dia fixing after pump (New HSR Item No-22.185.2)

White washing with lime to give an even shade New work (three coats) (HSR item No11.61.1)

Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end): 80 mm nominal bore (New HSR Item no 22.98.7)

Providing fixing of Header Assembly/Manifold 3" to connect the filtration unit (loose) (Rate app. By worthy Administrator)

Providing, lowering, laying in trenches, aligning, fixing in position and jointing at all level/depths cast iron (Cl) standard specials plain /flanged/ socketed confirming to IS13382 with rubber ring, nut bolts and rubber sheet such as tees, bends, tapers, caps etc. complete including all material, labour, testing and commissioning along with pipe line as per Technical Specifications and as per direction of Engineer. HSR Item No 20.69.1 Up to 300mm dia (100 KG per pumping Unit)

Providing & fixing cast iron double flanged swing check type reflux (non return) valves PN-1.6 marked with IS:5312 including nuts & bolts marked with IS:1363, rubber sheet marked with IS:638 etc., carriage loading,unloading, stacking, handling, re-handling etc. Complete in all respect to the satisfaction of Engineer-in-charge 150 mm i/d (New HSR Item No.20.11.3)

Providing and laying 50mm thick factory made cement concrete interlocking paver block of M -30 grade made by block making machine with strong vibratory compaction, of approved size, design & shape, laid in requiredcolour and pattern over (BIS 15658:2006) and including 50mm thick compacted bed of coarse sand, filling the joints with line sand etc. all complete as per the direction of Engineer-in-charge. (New HSR Item No 10.75)

Excavating trenches of required width for pipes, cables, etc including excavation for sockets, and dressing of sides, ramming of bottoms, depth up to 1.5 m, including getting out the excavated soil, and then returning the soil as required, in layers not exceeding 20 cm in depth, including consolidating deposited layer by ramming, watering, etc. and disposing of surplus excavated soil as directed, within a lead of 50 m: All kinds of soil Pipes, cables etc. exceeding 300 mm metre dia. but not exceeding 600 mm dia (New HSR Item No-4.16.1.3)

Earth work in excavation by mechanical means (Hydraulic excavator)/manual means over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan) including getting out and disposal of excavated earth lead up to 50 m and lift up to 1.5 m, as directed by Engineer-in-charge.(New HSR item no. 4.12.1)

Surface dressing of the ground including removing vegetation and in-equalities not exceeding 15 cm deep and disposal of rubbish, lead up to 50 m and lift up to 1.5 m. All kinds of soil (HSR item no 4.4.1)

Steel reinforcement for R.C.C. work, where not included in the complete rate of RCC, including straightening, cutting, bending, placing in position, binding, wastage, overlaps, welded joints, spacer bars, chairs, stays, hangers and annealed steel wire etc.complete in all respect below plinth level (Cold twisted bars) (HSR item No 6.33.3)

Providing, lowering, laying, cutting (cut surface to be uniformly finished), jointing with rubber rings marked with IS : 5382 and testing of SPIGOT AND SOCKETTED RCC, NP2 MARKED WITH IS : 458-1988 and specials into trenches for all depths including carriage, loading, unloading, stacking, handling, re-handling etc. complete is all respects to the satisfaction to the Engineer - in -charge. 450 mm i/d from outlet to tank in complete chak (HSR Item No 20.62.6)

1 : 1 ½: 3 ( 1 Cement: 1 ½ coarse sand (zone-Ill) : 3 cum graded stone aggregate 20 mm nominal size) (HSR Item No 6.1.1)

Supply and erection of alfa valve(Rate approved vide XEN,CAD Kurukshetra letter No. 2082/5A dt. 29.6.2018)(N.S. item)

Construction of control room/regulation cum watch and ward hut as per approved design and drawing including water supply, Sanitary fittings, electric fittings, septic tank and other items as required etc (Roof covered area 20' X 23.75') As per approved design and drawing

Complete operation and watch & ward of the project 1+3 year including operation of pump house, pipe line and accessories, electromechanical solar plants complete in all respect.

Complete Maintenance of pump house, pipe line and accessories, electromechanical, solar plant etc complete in all respect (36 months) @ 0.5% per year of total amount excluding earth work.

Supply and jointing three core submersible flat cables of approved make with bare bunched copper conductor insulated and sheathed with PVC for submersible pump motors /fountain lights etc with voltage grade 1100 volts marked with IS:694, 1990 including cost of jointing, materials as well as carriage, loading, unloading etc. complete in all respect up to the entire satisfaction of Engineer- in-Charge. Submersible Copper Cable 3 Core 16 sqmm HSR Item No 24.5.1.6

Construction of Desilting chamber including baffle walls to break the velocity of water to setteled down the heavier silt particlesas per design and drawing Optional Item Where heavy silt exist in water i.e. Yamuna Water

Survey, planning, design, drawing and hydro-analysis of the complete piping system, pumping units and solar plant to check adequacy of the complete MI infrastructure and vetting it from the Government institute since estimated quantities are based on the tentative design parameters, including preparation of warabandi (calculation based on @ 1% of total cost of estimate)

Preparation and implementation of warabandi of the complete chak and Identification of training needs of the farmers, preparation of training modules on various subjects concerning operation and maintenance of the MI systems, Solar array & pumping systems and cropping pattern etc., and providing necessary training to the farmers as per the identified needs. Necessary training shall be provided to the WUA members and the staff identified by the Engineer also for all activities involved in the O & M of the complete MI System including

Supply & Installation of valve regulated solar batteries as per IS 16270:2014 (reaffirmed 2019) have autonomy time of 15 days. 200 AH Lithium Battery.

Providing and installation of fire extinguisher with sufficient number of sand filled bucket, (NS item)

Providing and fixing of 4'x5' Iron sheet bounded welded with 2" dia Iron pipe having height of 5' anchored in concrete block 1'x1'x1.5' in groved duly painted and writing the site details (NS Items)

SURYA INTERNATIONAL ENTERPRISE PRIVATE LIMITED