SPL REPAIR TO COOK HOUSE AND DINING HALL BLDG NO P-252 AND P-253 OF 11 CSR UNDER GE (WEST) JRC

Amount

Demolition of cement concrete in ground floor and paving n.exc 15 cm thick (below or above ground level complete

Demolition of brick or stone masonary built in cement mortar complete

Taking down cement plastering on stone wall/brick wall etc including racking out of joints hacking for key scrubbing down with water etc

M&L brick work with sub-class 'B' bricks, straight or curved on plan exceeding 6 M mean radius built in CM 1:6

M&L brick work with sub class B bricks, straight or curved on plan to any radius in half brick thick wall built in CM 1:4 complete all as spd and directed

M&L Cement concrete type D 2, 1:4:8 (using 40 mm graded stone aggregate) in sub base of flooring, hard standing,Manhole, drain etc

M&L 75mm thick PCC 1:3:6 type C2 (using 40mm graded stone aggr) as in plinth protection/path finishing the surface even and smooth without using extra cement complete all as spd and directed. Note : Plinth protection shall be laid in (1:20) slope. The concrete shall be laid at a stretch not exceeding 3metre in length. Joint gap between adjoining slab, at corners and at junctions of walls shall not exceed 10mm in width and shall be sealed with mastic filling i.e. one part of bitumen 85/ 25 grade mixed with 3 part of sand. Top surface of concrete shall be finished even and smooth without using extra cement. Joints shall be provided at not more than 3 metre interval at corner and as junction of walls.

M&L 10mm thick rendering in CM 1:3 on brick/concrete surface as in ceiling and finishing the surface even and smooth with out using extra cement.

M&L 15mm thick rendering with water proofing liquid as per manufacturere instruction of approved make : Like : Sica/Dr Fixit/Fosroc on wall in CM 1:4 on brick/concrete surface and finishing the surface even and smooth with out using extra cement.

M&L 15mm thick rendering on wall in CM 1:6 on brick/concrete surface and finishing the surface even and smooth with out using extra cement.

Demolition of floor hearth or wall tiling including cement mortar bedding (not backing ) removing serviceable tiles to store and rubbish of the premises

M&L coloured Glazed ceramic tiles in vertical surface 350x 250x 7 mm/ 450X 350X 7mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match the surface over 10 mm thick cement plaster in CM 1:4.

M&L Non skid Coloured ceramic tiles 7 to 8 mm thick (squre or rectangle) area of each tile exce 0.11 SqM but not exceeding 0.18 SqM in floors etc, set and jointed in neat cement slurry and pinted in white or coloured cement to match with including 15mm thick screed bed in CM 1:6.

Non - skid Ceramic tiles 7 to 8 mm thick area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match in floors etc, set and jointed in neat cement slurry and pinted in white or coloured cement to match with including 15mm thick screed bed in CM 1:6.

Demolition of Stone slabs and tiles of any description or thickness in floors, aprons etc. laid bedded and pointed in any mortar.

M&L Machine cut kota stone slab flooring of size not less than 550mm x 550mm and 20-25mm thick over 15mm thick cement screed bed in CM 1:6 laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing upto mirror finished complete.

M&L Machine cut kota stone slab flooring 20-25mm thick as in skiritng, riser of steps etc laid over 10mm thick cement plaster in CM 1:4 laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing upto mirror finished complete.

M&L 20mm Granie (of any type) work(table rubbed and polished) in steps, jambs , pillars, window cills, cooking platforms, and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite over 15mm thick cement screed bed in CM 1:4 complete all as spd and directed.

Rounding/moulding to edges of Kota stone slabs, marble stone, granite stone slabs one edge, such as in steps, cooking platform , and other similar situations etc

Taking down chowkats or frames with shutters (without taking of shutter from the frame)of any description alongwith fittings n.exc 1.5sqm each

Taking down chowkats or frames with shutters (with out taking of shutter from the frame) of any description alongwith fittings exc 1.5sqm n.exc 4 sqm each

Taking down shutters of any description not exc 1 Sqm and not exc 2 sqm each and refixing in same opening after necessary all repairing.

S&F pressed steel door frame with one or more rebate including necessary fixing lugs, hinges, lock stricking plate of size 105 x60mm

S&F pressed steel door frame with one or more rebate including necessary fixing lugs, hinges, lock stricking plate of size 125 x60mm

M&L for PCC Type B0-1:2:4 using 12.5mm graded aggregate as in filling of pressed steel frame, hold fasts and similars articles

Cutting holes in brick walls in cement mortar for inserting holdfasts and making good dismantled portion in cement mortar 1:3 or cement concrete 1:2:4 Type B-1 as required built in cement motar in brick wall depth of embedded portion of holdfast exc half brick but n exc one brick

S&F 2nd class hardwood glazed and skelton door shutters 35 mm thick divided into squares open rebated and prepared to receive glass, gauge etc edges of framing plain, chamfered, rounded tfitted with mltred beads for securing glass etc, size of members as specified in SSR Pt 1 section 8 clause 8.20 (b) supplied and fitted to chowkats with plain, chamfered or rounded mited and rebated bars any numbers.

S&F 35mm thick flush door shutter, solid core construction with block board core, and plywood face panels, commercial type on both side complete all as sped and directed.

Solid PVC door frame of size 50 x 47 mm made out of 5 mm plain colour PVC sheet reinforced with MS square tube

S&F factory made solid panel pvc door shutter 30mm thick (style) consisiting of frame made out of M.S. Tubes for top & bottom rails M.S. frame shall be covered with heat moulded plain colour PVC `C' channel having a PVC sheet strip of 20mm width struck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail, panelling of plain colour PVC sheet to be fitted in MS frame welded/sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, fixing in the frame at the site as per specification & drawing.

Steel window/ventilator 1.25 mm thick Box type ERW hollow P section of size 60mm x 25 mm single rebated comprises skelton shutter ERW Sec 50 MM x 20 mm and 1 mm thick and two openable leaf consisting two Nos sash bar of T-section 20 mm x 3mm complete welded to frame with one vertical mullion of ERW box type T section of size 60mm x 25 mm and 1.25 mm thick including cuttings holes and making good dismantled portion in PCC (1:2:4) type B-1, including shop coat primer and following fittings welded to shutters:-i) Hold fasts 150 mm long,12mm x 3mm made to shape -04 No’s, (ii) Handle of Z sec 20mm x 25mm , 100mm long per leaf -1 No’s (iii) MS tower bolt 150 mm long per leaf -2 No’s (iv) Z sec 20mm x 25 mm , 100 mm long stopper per leaf -1 No (v) Cleat 55 mm long of hollow square 15mm x 20mm x 63 mm welded to hinges per leaf -01 No (vi) MS pintal hinges of size 75mm x 12 mm per leaf -02 Nos (vii) Fabrication and fixing arrangement complete Makes/Manufactures:- M/sTee Pee Enterprises Amritsar, M/S Ram fabricators Pvt Ltd Punchkula.

All as per description of item No 32 above but glazed shutter.

S&F framed work such as grills & gates, gratings with ends of bars shouldered on forged in spickes, framed guard bars, barred iron doors, ladders, framed balusters, walk ways, rallings, framework of water tanks and similar work conforming to Fe-290 Gde-E-165

S&F Galvanised mild steel wire cloth, 0.56mm nominal dia of wire and avg erage with aperature 1.18 mm fixed with tinned tacks, or galvanised wire staples.

S&F 3mm thick sheet glass ordinary quality and glazing with oil putty in square n.exc 0.50 sqm in each pane complete all as specified.

S&F Butt hinges, medium weight cold rolled 100 mm size ISI marked.

S & F 100mm Butt hinges, extruded aluminium alloy with galvanised mild steel hinge pin, anodised and fixed, type B-21

S&F aluminium anodised barrel tower bolts of extruded section 150mm long all as specified/

S&F Extruded aluminium alloy handles fabricated type anodised 150mm size

S&F aluminium alloy anodised sliding door bolts 250 mm long with hasp, staple (bolt type)and fixing clips of sheet cast or extruded section and fixing bolts and sliding bolts of extruded sections as specified.

S & F 300 mm mild steel ordinary rat tail rod pattern springs including roller and roller plate complete.

S&F Floor door stopper of aluminium alloy body and tongue, anodised, with hard drawn steel spring, fixed in floor 150 mm

Taking up or down 15 mm bore steel tubing and connection including cleaning for re-fixing or removal to store complete all as specifed and directed.

Taking up or down 25 mm bore steel tubing and connection including cleaning for re-fixing or removal to store complete all as specifed and directed.

S&F 15mm bore GI tubing medium grade fitting complete to wall and ceiling or laid in floor complete all as specifed and directed.

Refixing 15mm old GI tubing and connections in new or old position (Walls, ceiling, floors, etc.)

S&F 20 mm bore GI tubing medium grade fitting complete to wall and ceiling or laid in floor complete all as specifed and directed.

Refixing 20 mm old GI tubing and connections in new or old position (Walls, ceiling, floors, etc.)

Cutting chases, pinning in making good to facings where reqd and pointing in cement mortar 1:3 to ends or edges of shelves , for water tubing etc and making good, cutting exc 10cm girth but not exc 20cm girth in stone walls

Dismantiling of water tanks of capacity exc 1000 & n exc 2000 ltrs incl all necessary fittings complete.

Disconnecting existing tanks exc 250 & n exc 500 ltrs, setting aside (or lowering if required) for repairs, cleaning, etc. and hoisting if required reconnecting and re-fixing in position. (Cleaning repairing, etc. measured separately)

Disconnecting existing tanks exc 500 & n exc 1000 ltrs, setting aside (or lowering if required) for repairs, cleaning, etc. and hoisting if required reconnecting and re-fixing in position. (Cleaning repairing, etc. measured separately)

Disconnecting existing tanks exc exc 1000 & n exc 2000, setting aside (or lowering if required) for repairs, cleaning, etc. and hoisting if required reconnecting and re-fixing in position. (Cleaning repairing, etc. measured separately)

S&F 2000 ltrs PVC rotational moulded polyethylene water storage tanks double layer made (cylindrical vertical with closed top ) hoisted and fixed in position all as spd in SSR part-I

S&F 25mm Gun metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed in repair

S&F ball float valve PTMT with epoxy coated aluminimum rod for 20 mm bore pipe high pressure with polythelene high density float and complete screwed for iron pipe.

S&Fin repair 15mm dia Bib taps long body cast copper alloywith fancy type chromium lated crutch or butterfly handle screwed down, scewed for iron pipes or for brass ferrule

S&F 15mm dia Brass stop valves chromium plated, fancy type with long shank and cup concealed type screwed down, highpressure with crutch or butterfly handle, screwed both ends for iron pipe or for unlori as specified and fixed in repairs.

S&F in repair 15mm dia fancy type pillar taps cast copper alloy with capstan heads chromium plated scewed down high pressure with long scrwed shanks and fly nuts screwed for iron pipes

S&F in repair Vitreous china wash hand basin (550X400mm) white, flat back excluding taps, including brackets &32mm waste cuppling complete all as specifed and directed.

S&F Vitreous China Water closet (Squatting pattern) "Orissa Pattern" size 580x 440 mm white with 'P' or 'S' trap, front or back inlet and foots rests any pattern (excluding flusing cistern and flush pipe) in repairs complete.

S&F 10 Litre PVC valveless syphonic action flushing cistern low level white with inlet ball valve, float and handle including brackets and flush pipe of polyethylene of low or high density or PVC 32 mm dis for low level cistern in repairs

S&F 15mm PVC connection 450mm long with PTMT nuts of superior quality as specified

Supply and fixed Soap dish, any type fixed to walls with plugs with chromium plated brass screws

S&F for brass chromium plated Tubular towel rail, 20mm dia, D type, 60cm long between flanges etc complete all as spd and directed.

S&F brass chromium plated shower rose 125mm size complete all as spd and directed.

Demolition of wall and ceiling boards (fibre, pulp, insulation, etc.) or insulation boards/slabs/ blankets, any thickness, including cover fillets

Providing & fixing false ceiling at all heights with GRG (Glass Fibre Reinforced Gypsum) false ceiling tiles with semi perforated 12mm thick micro tegular edged GRG false ceiling tiles of Size 595 x 595 mm of approved texture, design and patterns having moisture content less than 2%, humidity resistance of 99%, NRC0.50 to 0.75 as per IS 8225:1987, Noncombustible as per BS 4 76 (part 4 )-1970 and light reflectance of 85% (minimum) to be laid in true horizontal level suspended on interlocking metal T-Grid of hot dipped galvanized iron section of 0.33mm thick (galvanized @ 120 grams per sqm including both sides) comprising of main-T runners of size 15 x 32 mm of length 3000mm,cross-T of size 15x 32mm of length 1200mm and secondary intermediate cross-T of size 15 x 32 mm of length 600mm to form grid module of size 600x 600mm, suspended from ceiling using galvanized mild steel items (galvanizing @ 80 grams per sqm) i.e 50mm long, 8mm outer diameter M-6 dash fasteners, 6mm dia fully threaded hanger rod upto 1 OOOmm length and Lshape level adjuster of size 85x25x2mm. Galvanised iron perimeter wall angle of size 24x 24x0.40mm of length 3000 mm to be fixed on periphery wall I partition with the help of plastic rawl plugs at 450 mm center to center and 40mm long dry wall wood screws. The work shall be carried out as per specifications, drawing and as per directions of the Engineer-in-Charge.

S & F 4mm thick aluminium composite panel sheet in cladding/panelling (of any colour) with aluminium frame work including all necessary SS screws and rowl plugs incl silicon filling at the joint of the two sheets are as spacified and directed by Engr in Charge.

Dismantling of brick tiles single layer as in roof covering complete all as specified

Demolition of mud in roofs any thickness including plastering and leeping(whether full thickness removed or only a part thereof) all as specified.

Cleaning/Roughening surfaces of old concerete floor/roof by picking , sweeping clean and washing down with water to romove the dust etc complete all as spd.

M&L for providing, cement concrete in roof kerbs or mud stops, rounded or chamfered on edges and PCC pedding with cement concrete type B-1, 1:2:4 (using 12.50mm graded stone aggregate) to top surface of slab in slop 1:40,with using water proofing liquid as per manufacturere instruction of approved make : Like : Sica/Dr Fixit/Fosroc,finishing the surface even and smooth without using extra cement complete all as specified.

M&L 10mm thick rendering on top of roof slab in cement mortar 1:4 with using appropriate WPC as per manufacturer's information from SIKA Plastocrete Plus/FOSROC/ DR Fixit/ STP/CICO on brick/concrete surface, finishing the surface even and fair without using extra cement.

Providing and applying liquid Polyurea-PU based hybrid elastomeric water proofing membrane at existing/newly constructed roofs, RCC structure like basement raft, retaining wall, water retaining structure, tunnels/subways and bridge deck etc. in two or more coats. The product must have pot life of >90 mins., tensile strength > 12.6 Mpa, elongation of > 500% conforming to ASTM D 2370 & puncture resistance of >200 N as per ASTM E 154 with min. consumption of 1.5 Kg per sqm for 1.2mm DFT in two- three coats. The surface needs to be primed with water soluble self impregnated epoxy primer in two coats to be applied @ 200-250 gms/sqm/coat prior to Polyurea -PU application. Furthermor, (in case the substrate is not suitable) 15mm plaster is advisable for surface prepration before application of the water proofing membrane to avoid pinholes or functional difficulties of the system (Make - Asian Paints, BASF & SIKA) Note:- The application shall be done by the authorised applicator of the manufacture with a letter of proof stating the authenticity of the applicator firm.

Taking down eaves gutters and rainwater pipes (any size or pattern), including all fittings, heads, shoes, bends, swan-necks, etc., including cleaning or refixing or removal to Store (measured overall as fixed along the centre line over fittings and accessories)

Dismantling of cast iron or reinforced concrete drain pipes of size 100mm dia, jointed in cement mortar and taking out of trenches, if required.

M&L 75mm PVC (SWR) floor trap, plain with CP grating including jointing with solvent cement complete all as spd and directed

S&F 110mm PVC (SWR) pipes single socketed in any length with rubber ring joints, fixed to walls complete

S&F 75mm PVC (SWR) pipes single socketed in any length with rubber ring joints, fixed to walls

S&F 110mm PVC (SWR) bends

S&F 75 mm PVC (SWR) bends

S & F for PVC 110mm (SWR) vent cowl

M&L for repairing of R.C.C projections, chajjias, roof slab, facia etc in patches not exceeding 3 Sqm in each patch by necessary preparation. Scarpping, cutting, chiseling derusting and cleaning exposed reinforcement, surfaces of damaged, loose R.C.C surfaces and applying one coat of rust stop solution of approved make and filling the surfaces with cement concrete (1:1.5:3) using 12.5mm graded crushed stone aggreagates and reinforced with welded TMT bars/mesh (If Reqd) of weight exc 2 kg per sqm but n.exc 3kg/sqm with or without facia and finished with cement and sand motar (1:3) using coarse sand and thickness of R.C.C member n.exc 100mm including necessary form work and applying two coats of finishes to match with the existing surfaces in at any height complete all as specified and directed by Engr-in-charge. (Note : Cost of form work and welded mesh shall be deemed to be included in unit rate quoted by the contractor complete all as specified and as directed.

Dismantling of Asbestos cement (corrugated, semicorrugated, etc.) sheets in roof coverings

Dismantling wrought iron or mild steel work of any description not otherwise provided for

Excavation in post holes each nexc 0.50 cum , getting out, returning filling in and ramming earth or broken rubble mixed with earth in layers not exceeding 25cm in soft/loose soil

M & L for PCC (1:2:4) typeB-2 (using 40mm graded crushed stone aggregates) lean concrete as in foundation, filling and mass concrete of post complete all as specified .

S&F Steel work as in tubular section for Post, Purline etc including special shaped washer , angle cleat, holdfast, gussete plate etc. complete using ERW or induction butt welded tubes conforming to I. S.1161- 1979 grade St.-240 cut or notched forming holes, without any attachment including drilling, fitting, riveting and or welding or connecting with bolts and nuts (incl rivet or nut and bolts) providing and fitting angle cleats Gussete plates etc also for welding plumbing, truing up and fixing complete as directed by Engr-in-Charge.

M&L pre-painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50 mm thick of an colour having tensile strength of 550 Mpa as in roof covering/ cladding to wall , fixed with J or L type or cranked hook bolts complete as directed by Engr-in-charge.

M & L for Pre-painted galvalume aluminum zinc coating GI based Plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with J or L type or cranked hook bolts complete as directed by Engr-in-charge.

M & L for Hand rails, half round or other stock section or core for wooden hand-rail straight portion, drilled and countersunk for balusters running bars, for doors, balusters, nosing to steps including embeding in concrete and screwing etc. wind ties for roof including securing bolts; posts and struts in fencing including cutting tops to shape as directed, drilling holes, notching for wire, etc.; flat iron fillets (for securing wire mesh etc.) including all necessary drilling, bolting or riveting, etc., and similar work conforming to Fe-290 Gde E-165

M & L for applying two coat of synthetic enamelled paint over one coat of pink primer including preparation of new wood surfaces of any description not otherwise described over 10 CM girth or width all as directed by the Engr in charge

M & L for applying one coat of synthetic enamelled paint including preparation of old treated wood surfaces of any description not otherwise described over 10 CM girth or width all as directed by the Engr in charge

M & L for applying two coat of synthetic enamelled paint over one coat of red oxide primer including preparation of new steel surfaces of any description not otherwise described over 10 CM girth or width all as directed by the Engr in charge

M & L for applying one coat of synthetic enamelled paint including preparation of old decorated steel surfaces of any description not otherwise described over 10 CM girth or width all as directed by the Engr in charge

M & L for applying white wash of 3 coats as in ceiling incl preparation newly plastered surfaces as specified and directed.

M & L for applying white wash of one coats as in ceiling incl preparation old painted surfaces as specified and directed.

Material and labour for preparation of new plastered surfaces on walls and applying two coats of oil distemper over one coat of chalk whitening complete all as specified.

Complete removal of existing treatment on wall and applying Two coat of Oil distemper (white or tinted) complete all as specified and as directed by Engineer-in-Charge.

Material and labour for preparation of new plastered surfaces on walls and applying two coats of cement base paint over one coat of cement primer complete all as specified.

Complete removal of existing treatment on wall and Material and labour for preparation of old plastered surfaces on walls and applying two coats of cement base paint over a coat of cement primer complete all as specified. and as directed by Engineer-in-Charge.

Excavation in trenches not exc 1.5m wide and not exc 1.5m deep for foundation etc for shafts, wells, cesspits , manholes pier holes, etc n exc 10 sqm on plan and n exc 1.5m in depth and getting out in soft/loose soil complete all as specified and directed.

Demolition and breaking up drain pipes 150mm bore (salt glazed ware, AC or Reinforced) set in cement mortar all as spd and directed.

M &L for 150mm bore SGSW drain pipe (Grade-A) laid in trenches and jointed in CM 1:1 and tested complete all as spd and directed.

M&L for concrete bed for 150mm in PCC 1:4:8 type D-2 (using 40 mm graded stone aggregate) to drain pipes including packing under, haunching against the sides of pipes after they are laid and tested complete all as specified and directed.

Demolition of re-inforced cement concrete of any description in any position not otherwise specifically provided for.

M&L RCC 1:2:4 type B-1 (using 20 mm graded stone aggregate) as in precast RCC manhole / septic tanks ,drain,covers including all form work and setting in CM 1:6 all as specified and shown on drgs.

M&L for PCC 1:2:4 type B-1(using 20 mm graded stone aggregate) as in channels/benching of manhole, drain,laid to shape and slope and surfaces finished even and smooth using extra cement, complete including all form work etc all as specified and directed.

M&L mild steel TMT bars 6mm to 8mm dia cut to length bent to shape required including cranking bending and binding with and including mild steel wire annealed not less than 0.9 mm dia or securing with clips.

Material and labour for cement concrete 1:3:6 Type C-1using 20 mm graded stone aggregate as in copings, weathering, slightly rounded or chamfered angles and throating, complete all as specified and as directed by the Engineer-in-Charge.

Returing, filling in, including spreading, leveling, watering and well ramming in layers not exceeding 25 cms in soft /loose soil.

Removing excavated material n exc 50 m depositing where directed at a level n exc 1.5m above the starting point complete all as spd.

Taking down carefully aluminium / copper point wiring (light / fan / socket or power) complete including fitting such as switches, ceiling roses, socket, light fittings, regulators etc complete and making good disturbed surfaces of walls, floors

Taking down main switch / DB as directed by Engineer-In-Charge.

Taking down unserviceable submain/ LT cable/service wire of any size as directed by Engineer-In-Charge.

M & L for concealed point wiring complete with 1.5 sqmm single core multistranded copper conductor FRLS, PVC insulated and unsheathed cable 1100 volts grade drawn through & including PVC conduit ,medium grade with accessories like bends, tees, junction boxes etc fix on wall or ceiling surfaces all as specified including 1.5 sqmm , FRLS type , copper multistranded cable as earth wire including pressed steel sunken boxes for mounting of switch/sockets and regulator and including cover plate white colour all as specified and directed for: One 3 pin socket outlet, 5Amps, independent board

One 3 pin socket outlet 5 amps on same board.

One light /fan point/holder /mirror lightcontrolled by one one way switch as directed engineer-in-charge

Supply and fixing LED light fitting mirror type with high out put diffuser 2 feet, 10 watt 220 V AC decorative type with driver holder and LED lamp including connecting up with three core flexible copper conductor cable of suitable size complete

M & L for concealed point wiring complete with 2.5 sqmm single core multistranded copper conductor FRLS, PVC insulated and unsheathed cable 1100 volts grade drawn through & including PVC conduit ,medium grade with accessories like bends, tees, junction boxes etc fix on wall or ceiling surfaces all as specified including 2.5 sqmm , FRLS type , copper multistranded cable as earth wire including pressed steel sunken boxes for mounting of switch/sockets and regulator and including cover plate white colour all as specified and directed for:

supply and Refixing FLUSH/PIANO type switch 1 way 16A,

supply and Refixing piano/flush type socket 6/16 amp 5 pin

supply and Refixing piano/flush type switch 1 way 6A,

supply and Refixing piano/flush type socket 6 amp 5 pin

Supply and refixing stepped type electronic fan regulator flush type as reqd complete all as specified and directed.

M & L ceiling rose surface bakelite 65 x 50 mm three terminals complete all as specified.

S&F Factory made sheet metal enclosures double door type made out of CRCA 1.2 mm thick M.S. sheet, powder coated, partly embedded in wall, IP-43 protection, VTPN DB with 200 Amps rated bus bar, 4 way, 415 volts, vertical type, dust and vermin proof, suitable for incorporation of MCCBs/ MCBs, factory made, including thermal based release adjustable type 4 pole 63 Amps, 50 Hz, 415 Volts with rupturing capacity 16 KA and making good distrubbed surfaces with matching colour, complete all as specified.

S & F sheet metal enclosure for DB’s (Double door type) when MCB’s to be used, single pole and neutral, 8 ways with 200 ampere rated bus bar, 240 volts fixed sunk / flush to the wall with IP-43 and IK-09 protection complete all as specified and directed.

S & F MCB SPN, 240 volts, 40 to 63 Ampere, rupturing capacity 10 KA, ‘B’ curve type complete all as specified and directed.

Supply & reFixing MCB single pole, 240 volts, 6 to 32 Ampere, rupturing capacity 10 KA, ‘C’ curve type complete all as specified and directed.

Supply & Refixing LED tube light fitting 20W (Double side) including LED lamp 20W with 2100 lumen output with internal surge protection device of 4KV with voltage band of 140-280V CRI-6500K (White light) fixtures box type and connecting electrically to ceiling rose using PVC insulated and overall sheathed flexible copper conductor of size 0.50mm 4 core complete all as specified and directed.

Supply and refixing lamp holder ,pvc /polycarbonate type with back plate suitable for batten fitting

M & L for earthing complete with galvanised earth plate electrode 600 X 600 X 6 mm thick buried directly in ground (earth pit not less than 2.25 m below ground level) with top edge of earth plate not less than 1.5 m below normal ground level, connected to galvanised earth lead wire 4 mm dia by means of nuts, bolts, check nuts & washers of galvanised iron or steel all as shown on electrical plate No. 3 of MES schedule 2009, Part – I (Specifications) and connected to main switch board / main DB’s / earthing test point including all necessary excavation and earth work in any type of soil, adequate quantity of charcoal dust & common salt all around the earth plate minimum 150 mm in all directions with & including watering pipe 20 mm dia GI medium grade, GI funnel made out of 0.63 mm thick GI sheet, wire gauge, 50 mm thick RCC cover in PCC 1:2:4, type B-1, duly reinforced with 6 mm dia mild steel round bars @ 150 mm both ways center to center with suitable lifting handle to cover, earth pit of PCC 1:3:6 type C-1, GI protection pipe light grade 15 mm bore up to 7.5 m length from earth electrode & engraving of earth marking on nearby building with CM 1:4 plate size 200 X 150 X 15 mm & painting of earth result etc. including testing on complete all as specified and directed. Note : (i) Earth lead and protection pipe beyond 7.5 m shall be measured and Paid separately. (ii) On testing after completion of job, if desired earth resistance is not obtained, the earthing shall be redone by the contractor without any extra cost to Govt.

M & L for sub main wiring with 1100 volt grade two single core FRLS Wire PVC insulated and unsheathed cable with stranded copper conductor 6 sqmm drawn into and including electrical grade PVC conduit not less than 25 mm dia with IS 9537 (Part-III) 1983 mark, or relevant ISI mark with all accessories fixed concealed including chase cutting in brick/ stone masonry for fixing conduit and making good the disturb surfaces of wall as per existing including 6 sqmm multi - stranded copper conductor as earth wire in green colour complete all as specified and directed. Including taking down old unserviceable sub main wiring. Note : Two runs of 6 sqmm PVC FRLS multi stranded copper cable wire and One run of 6 sqmm PVC FRLS multi stranded copper cable earth wire and One run (01 meter) PVC conduit of suitable size ISI mark will be measured and one unit length.

M & L for laying of LT cable of 1100 volt XLPE insulated and PVC sheathed of size 25 sqmm 4 core with cable gland including taking down old unserviceble cable complete all as specified and directed by Engineer-in-Charge.

Excavation in trenches in soft/lose soil not exceeding 1.5 Mtr wide and not exc 1.5M depth for laying of UG cables and getting out all as specified and directed

Returning, filling, including spreading, levelling, watering and well ramming in layers not exc 25cms thick of soil complete all as specified and directed.

M & L river sand in trenches as cable cushioning 8 cm below the cables and 15cm above the cable which is to be punned down to 10m all as specified and directed.only punned thickness will be measured.

Removing the surplus excavated materisl/soil to a distance not exc 50Mtrs and depositing, where directed at a level not exceeding 1.5 Mtr above the starting point all as specified and directed.

Supply and lay burnt bricks sub class 'B' standard size laid across the cable in trenches as protection to the cable all as specified and directed.

Supply and Refix exhaust fan, Metal body heavy duty AC single Phase. 230V of size 300m sweep with, blades, and frame and louvers incl opening of hole in wall and matching with existing finish all as specified and directed.

Supply and Refixing LED street light fitting 35 Watt 230 V AC outdoor type with high pressure die cast aluminum hosing and heat resistant complete with driver, lamp bracket with impact and corrosion resistant including thermalmanagement in multiple optics complete withIP 65/66 protection complete

supply and fixing recess /ceiling mounting LED light 1x36 watt cool white light of 6500k complete all as specified and directed .Supply and fixing LED luminaire 600 mm x 600 mm, 35/36 watt, 220 V AC recessed type with high efficiency PMMA diffuser soft glare free light completewith driver, holders & LED lamp suitable for roof ceiling including connecting up with driver three core flexible copper conductor cases of suitable size complete

PAUL CONSTRUCTION CO. (BID ID -3326005)

SARASWATI CONSTRUCTION CO (BID ID -3320123)

M/S Vinod Kumar (BID ID -3320097)

M/S Kuldip Construction Co. (BID ID -3319695)

Sachdeva and Company (BID ID -3328255)