PROVN OF 03/HIGH MAST LIGHT AT MIL STN TALBEHAT

Amount

1. Supply, installation and testing of 12.5 mtrs high mast confirming to IS-875 (Part-III) - 1987, made out of steel plates confirming to BS-M10025 cut and holded to form a tapered polygonal section in two section having 20 sides, plate thickness of base section 4 mm and of top section 3 mm , length of base and top section as 8.25 mm and dia of base section 360 mm and top section 150 mm in two section suitable for wind speed of 180 km/hour with double drum winch and stainless steel rope of grade AISI 304, 7/19 construction, 6 mm dia tralling cable copper conductor 5 core, 2.5 sqmm EPR/PCP insulated, PCP sheathed incl power tools of 1 HP/1.5 HP capacity (motorised system for bringing up and down the lights) and aviation light (LED type) lightening arrestor spike incl feeder pillar suitable for operation of light and motor as per manufacturer design. The mast should consist of 6 Nos LED flood light fitting 150 Watt with two Nos of external control gear box. Make Crompton Greaves or equivalent of Philips/Bajaj with all accessories incl lamps mounted on suitable brackets as per manufacturers catalogue incl RCC foundation excavation and earth work in any type of soil complete all as per manufacturer inctruction/design and its reflection should be carried under the supervision of manufacturer, complete all as specified and directed.

(a) ELECTRON PART:- (i) Construction of suitable shallow foundation with design mix (M 25) concrete for the high mast considering the safe soil cearing capaity at site as per foundation of the drawing approved by AGE (I) Talbehat (ii) Errection of the high mast with the help of suitable equipment and wiring of luminaries with all wiring material and labour- Job - 01 (iii) Earthing complete with galvanised steel earth plate electrode 60x60cmx6mm thick, burried directly in ground (each pit not less than 2.25m deep below ground level) with top edge of the plate not connected to galvanised iron strip 25x4mm all as shown in electrical plate No. 3 connected to earthing test point all as specified or indicated Job Qty-02. (iv) Installation of control panel suitable foundation incl all material and labour Job 01

(b) LT OUTDOOR PANEL :- Fabricate, supply, install, testing and commissioning of LT out door total enclsoed LT panel board of size 0.75mX0.5mX0.3m approx totally enclosed made out of 3mm thick CRCA sheet dust and vermin proof with front opening 440V 3 Phase 4 wire having 200 Amps capacity aluminium bus bar insulated wth sleeves, incoming MCCB TPN 63 Amps 440 Volts 25 KA - 01 No and copper wiring with multistranded cable including timer switch electronic type 01 No with necessary MCBs SP 10 Amp 09 Nos contactors etc, cable glands, lugs,suitable control circuit for automatic switching on and off of the mast and two coats of synthetic enamel paint over a coat of red oxide primer and making necessary pedestal 300 mm height from floor level with PCC work complete all as specified.

(c) Provn of wiring from panel to light fitting with single core 4 sqmm copper conductor cable drawn through MS rigid/ flexible conduit with necessary fittings 400Mtr.

(d) Provn of single pointed air termination rod and necessary fitment required for protection against lightning protection. (Earthing shall be measured and paid seperately)

(e) Testing and commisioning:- (i) Testing & Commissioning of above high mast system complete. Note:- Rate quoted against this item shall be deemed to included for for all (i.e a to e) above provisions.

Excavation in in trenches not exceeding 1.5 mtrs wide & not exceeding 1.5 mtr in depth in soft or loose soil & getting out complete all as spfd & directed.

Excavation in in trenches not exceeding 1.5 mtrs wide & not exceeding 1.5 mtr in depth in Hard rock & getting out complete all as spfd & directed.

Returning , filling in spreading, levelling, watering & well Ramming in layers not exc 25cm thick complete all as spfd & directed.

Removing excavated materialn not exceeding 50mtr &deposited where direceted at a level not exceeding 1.5mtrabove the ground level.

Supply and laying river sand for cushioning to underground cable in layers of 23 cm (8 cm deep before laying of cable and 15cm deep over the cable) after laying the cable in trenches including punning thickness up to 18 cm , complete all as specified and directed.

Supply & Laying un reinforced precast concrete cable cover, Class LV type-1 flat size 250 mm x 150 mm x 40 mm for cable protection laid length wise perpendicular to the adzes of cable complete all as specified and directed.

8. Supply and fixing light grade galvanised iron pipe 50 mm nominal bore conforming to IS : 1239 and ISI marked with all fittings fixed on walls/poles, crossing of road etc for protection of cable complete all as specified and directed

Supply, laying, Jointing and testing XLPE insulated, armoured heavy cable of 10 Sqmm, 4 core with aluminium conductor suitable for rated voltage of 1100 Volts grade conforming to IS: 7098( part-I) of 1988 and laid in trenches/pipe / ducts or on pole including cost of all types of cable lugs, cable glands complete all as specified and directed

Note :- Debris obtained from all items should be removed in low lying areas as directed by Engr-in-charge out of MOD Land. (Rates quoted for items are deemed to be included for this, where removal of debris in the items is not considered.)

M/s Indu Enterprises (BID ID -3171495)

M/S Kharya Associates (BID ID -3171538)

HARNAM SINGH ANIL SINGH (BID ID -3171773)