Annual Rate Contract for Repairing and Rewinding OF Centrifugal Pumping Sets MONO BLOCK and COUPLED Of Different Make Under PHED DIVISION Sadulpur

Rewinding of three phase squirrel cage induction motor of Monoblock pump sets including all necessary material and of the same characteristics as original with required size of super enameled copper wire (including cost of copper wire),'E' class insulation material and testing of motor on no load but to be guaranteed against testing on load at site, including transportation of motor pump to and from Div/AEn/JEn store complete as per direction of engineer in charge.

SUPPLY & FIXING OF SPARE PARTS FOR MONOBLOCK PUMPSET (MOTOR + PUMP)

Connection Plates

up to 10 HP

10 HP to 20 HP

Cooling Fan

up to 10 HP

10 HP to 20 HP

GM/SS bush

Upto 10 HP

10 HP to 20 HP

Mechanical reconditioning of Bearing sheet

Upto 10 HP

10 HP to 20 HP

Mechanical reconditioning ofImpeller sheet and Key way slot

Upto 10 HP

10 HP to 20 HP

Oil seal

Upto 10 HP

10 HP to 20 HP

Labour charge for opening and fitting of pump sets

Upto 10 HP

10 HP to 20 HP

Rewinding of three phase squirrel cage induction motor of HSC pump sets including all necessary material and of the same characteristics as original with required size of super enamelled copper wire (Including cost of copper wire) 'E' class insulation material and testing of motor on no load but to be guaranteed against testing on load at site, including making electric connection at site of installation of motor with starter, alignment with pump sets and transportation to and fro from installation site complete as per direction of engineer in charge at site.

Above 15.00 HP but upto 17.50 HP

Above 17.50 HP but upto 20.00 HP

Above 20.00 HP but upto 25.00 HP

Above 25.00 HP but upto 30.00 HP

Above 30.00 HP but upto 35.00 HP

Above 35.00 HP but upto 40.00 HP

Above 40.00 HP but upto 45.00 HP

Above 45.00 HP but upto 50.00 HP

Above 50.00 HP but upto 60.00 HP

Above 60.00 HP but upto 75.00 HP

Above 75.00 HP but upto 100.00 HP

SUPPLY & FIXING OF SPARE PARTS HSC PUMP SETS (MOTOR + PUMP)

Connection Plates

5 HP to 20 HP

20 HP to 30 HP

30 HP to 50 HP

Above 50 HP to 100 HP

Cooling Fan

5 HP to 20 HP

20 HP to 30 HP

30 HP to 50 HP

Above 50 HP to 100 HP

Fan Cover

5 HP to 20 HP

20 HP to 30 HP

30 HP to 50 HP

Above 50 HP to 100 HP

G.M./SS Gland Guide Bush

5 HP to 20 HP

20 HP to 30 HP

30 HP to 50 HP

Above 50 HP to 100 HP

Shaft with Sleeve Chuck Nut

5 HP to 20 HP

20 HP to 30 HP

30 HP to 50 HP

Above 50 HP to 100 HP

Shaft Chuck Nut

5 HP to 20 HP

20 HP to 30 HP

30 HP to 50 HP

Above 50 HP to 100 HP

G.M. Neck Ring

5 HP to 20 HP

20 HP to 30 HP

30 HP to 50 HP

Above 50 HP to 100 HP

Bush Shaft Sleeve of G.M.

5 HP to 20 HP

20 HP to 30 HP

30 HP to 50 HP

Above 50 HP to 100 HP

G.M. Gland Cover

5 HP to 20 HP

20 HP to 30 HP

30 HP to 50 HP

Above 50 HP to 100 HP

S.S. Shaft (Non Magnetic)

5 HP to 20 HP

20 HP to 30 HP

30 HP to 50 HP

Above 50 HP to 100 HP

G.M. Shaft Sleeve Check Nut

5 HP to 20 HP

20 HP to 30 HP

30 HP to 50 HP

Above 50 HP to 100 HP

M.S. Shaft Check Nut

5 HP to 20 HP

20 HP to 30 HP

30 HP to 50 HP

Above 50 HP to 100 HP

Cooling pipe set with nozzle & Nut

5 HP to 20 HP

20 HP to 30 HP

30 HP to 50 HP

Above 50 HP to 100 HP

AIR Cock

5 HP to 20 HP

20 HP to 30 HP

30 HP to 50 HP

Above 50 HP to 100 HP

JOB WORK FOR REPAIR OF PUMP MOTOR

Bearing Housing (rebuilding, turning & finishing)

5 HP to 20 HP

20 HP to 30 HP

30 HP to 50 HP

Above 50 HP to 100 HP

Bearing Cap (rebuilding, turning & finishing)

5 HP to 20 HP

20 HP to 30 HP

30 HP to 50 HP

Above 50 HP to 100 HP

Impeller Reconditioning for all type of Pump

5 HP to 20 HP

20 HP to 30 HP

30 HP to 50 HP

Above 50 HP to 100 HP

Labour Charges for Dismantling & Assembling of Pump

5 HP to 20 HP

20 HP to 30 HP

30 HP to 50 HP

Above 50 HP to 100 HP

Coupling with stud and rubber bush

5 HP to 20 HP

20 HP to 30 HP

30 HP to 50 HP

Above 50 HP to 100 HP

Supply & Fixing of tyre coupling sets according to relevant IS code in Centrifugal couple pump sets of approved make Unit. This job also included re-alignment of centrifugal couple pump set after fixing of tyre coupling set as per directed by Engineer-in charge.

Type 14 Nos. set

Type 15 Nos. set

Type 16 Nos. set

Type 17 Nos. set

Supply and fixing Ball bearing of Various size for centrifugal/monoblock pump set of ISI Mark as per specification and approved make by EIC.

6304 or equivalent size

6305 or equivalent size

6306 or equivalent size

6307 or equivalent size

6308 or equivalent size

6309 or equivalent size

6310 or equivalent size

6311 or equivalent size

6312 or equivalent size

6316 or equivalent size

6317 or equivalent size

6318 or equivalent size

6319 or equivalent size

NU319C or equivalent size

Suuplying of super enamal copper wire suitable for rewindind of induction motor (only procured for motor rewinding)

Preventive Mintenance

Routine maintenance of centrifugal coupled pump and motor including opening, cleaning, greasing and refitting / changing of ball bearing if required, gland refilling and replacing all rusted studs, replacing rubber bushes & coupling nut & bolts for coupling pulley, tightening all nut & bolts of foundation, baseplate, pump & motor etc. Checking & correcting alignment of pump & motor including necessary materials i.e. grease, nut & bolts, studs, washers, gland packing and rubber bushes etc. work done at site complete job

5 HP to 20 HP

20 HP to 30 HP

Above 30 HP and up to 50 HP

Above 50 HP and up to 100 HP

Replacing of damaged/broken gland packing plate with new gland packing plate suitable for centrifugal pump shafts and nut&bolts etc. complete job.

5 HP to 20 HP

Above 20 HP and up to 30 HP

Above 30 HP and up to 50 HP

Above 50 HP and up to 100 HP

Please Enable Macros to View BoQ information