ADDN /ALTN TO WOODEN /STEEL WINDOWS AND GRILLS IN BLDG NO. P-161 AND PROVN OF WORKERS CHANGE ROOM, CHAIN LINK FENCING NEAR ADM BLDG AND CERTAIN MINOR AND REVENUE WORK AT NCHC POWAI UNDER GE (NW) BHANDUP, MUMBAI

Amount

Taking down chowkats without taking off shutters from the frame exc.1.50 Sqm and not exc. 4.00 Sqm each.

Taking down chowkats without taking off shutters from the frame n.exc.1.50 Sqm .

Taking down cement or cement lime plaster on brick or stone wall etc., including racking out joints, hacking for key, scrubbing down with water etc.

M & L machine cut Cudappa stone slab 20-25 mm thick as in kitchen platform over cement screed base in CM (1:4), 10 mm thick laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab laying floor finishes srubbing and polishing complete all as specified and directed.

M & L for Rendering 10 mm thick in CM (1:4) on fair faces of brick work or concrete surfaces complete all as specified and directed.

M & L for Rendering 15mm thick in CM (1:4) in 02 coats (10 mm + 5 mm) surface finished even and smooth without using extra cement complete all as specified and directed

M&L for Rendering 15mm thick 1:4 CM in two coats (10 + 5) with water proofing compound including finishing the surface even and smooth without using extra cement. (WPC shall be measured and paid separately).

Supply Only integral water proofing compound

S&F Aluminium section in sliding Windows/Ventilators ,any type (sliding on minimum two PVC roller of best qulaity for each shutter), powder coated in approved colour (Thickness of powder coating not less than 50 micron), aluminium section (medium weight of series 'B') as section directed by Engineer-in-Charge, cut to size, jointed together with cadmium plated steel screws including rubber beading or gasket for aluminium sections for fixing glass/XPM jali and all necessary fittings complete, screws, plugs for fixing screws, etc all as specified and directed (Make : JINDAL/HINDALCO) Notes : (i) Weight of aluminium sections shall only be measured. (ii) Rate quoted by the contractor shall deemed to be inclusive of all necessary fittings and fixture such as roller, handle locks etc. Quoted rate shall be deemed including cost of rubber beading or gasket etc and will be not measured separately. (iii) Glass pane and wire meshwill be measured and paid separately under relevant items as supply only. .

Supply only 4mm thick Sheet glass, ordinary quality in squares n exc 0.5 sq. m in each pane complete all as specified and directed.

Supply only 4mm thick Sheet glass, ordinary quality in squares exc 0.5 sq. m in each pane complete all as specified and directed.

Supply only 4mm thick figured glass,tinted colour, pin head type, in square n.exc.0.5sqm in each pane for fixing aluminium frame complete all as specified and as directed.

Supply only Aluminium wire cloth 0.45mm nominal dia of wire and arrange width of aperture 1.40mm for fixing in aluminium windows along with complete all as specified and directed by the Engr-in-Charge

S&F Aluminium anodised Grills of approved design for window / ventilators and fixing with F/U channel all as specified and directed. Note: The Grills shall be of Model DG-102 or any other Model of Make Deco or equivalent make as approved by the GE.

S&F Aluminum anodised grill DG- 202 ( 10 mm x 8mm ) of Deco grill or equivalent fixed with 'F' section size not less than 20.60 x 15.20 x 1.5mm thick of approved make all as specified and directed. Note : (i) Make shall be of M/s Deco grill of M/s Associated Groups or equivalent as approved by the GE. (ii) Minimum thickness of anodizing shall be 15 microns.

S&F and mild steel framed work as in grills, greating and guard bar with end of bars shouldered and / or reveted or forged into spikes and similar works confirming to Fe-410 and Fe-310.

M & L for prepration of new plastered surfaces of wall and applying two coats of 100% anti fungal Acrylic exterior emulsion paint over one coat of primer all as per manufacture's instructions including necessary scaffoliding etc, complete all as specified and directed

M&L for preparation new plastered surfaces of walls and applying two coats of distemper over a coat of primer compelte all as specified and directed by EIC

M&L for preparaing of new or previously untreated steel surfaces of any description, over 10cm in width or girth, not otherwise described, and applying two coats of synthetic enamal paint over one coat of Red oxide, zinc chrome primer etc complete all as specified and directed.

All as per item no. 19 here-in-before but n. exc. 10cm width or girth.

Excavating in trenches not exc 1.5 m wide and depth not exc 1.5 m and getting out in soft/ loose soil.

S&F Angle iron in fencing posts, fixed independently, conforming to Fe-290 (Gde E-165)

S&F Flat iron fillets for securing chain link fencing, including all necessary drilling, bolting or riveting etc, & conforming to Fe-290 (Gde E-165)

S&F for Chain link fencing made out of 4mm dia galvanized steel wire, 100mm x 100mm mesh size fixed to any type of standard rails or fencing posts including straining bolts and binding wire etc. complete.

S&F for mild steel screw bolts (Machine made) 5 to 10mm dia n exc 5cm long.

S&F round bars 10mm dia for inserting & strengthing chain link fencing, conforming to Fe-290 (Gde E-165)

M& L for PCC (1:4:8) type D2 (using 40 mm graded stone aggregate) in foundations, filling and mass concrete.

M&L for RCC Nominal Mix (1:1.5:3) type A-2 (using 40 mm graded aggregate) as in foundation, includings rafts footings ,foundation beams,plinth beams, bases for columns etc complete all as specified and directed

M&L for RCC Nominal Mix (1:1.5:3) type A-1 (using 20 mm graded stone aggregate) as in columns,pillars,posts etc complete all as specified and directed

M&L for PCC (1:2:4) type B-1 (using 20 mm graded stone aggregate) as in plinth courses, strings courses, copings, kneelars, apex stones, bed plates, kerbs etc complete including necessary formwork all as specified and directed

M & L For Formwork to sides of concrete foundations, footings,bases of columns,raft and raft beams, plinth beam, flat, for rough finished surfaces of concrete, complete all as specified and directed

M & L For Formwork to sides pillars, columns,square or rectangular, flat, for rough finished surfaces of concrete, complete all as specified and directed

M & L for brick work with sub class 'B' Bricks straight or curved on plan, exceeding 6m mean radius, built in CM 1:6 complete all as specified & directed.

M & L for brick work with sub class B bricks, straight or curved on plan to any radius in half brick thick wall built in CM (1:4)

S&F Granite (of any type) stone 20mm thick machine cut and machine polished (mirror finish) bedded and jointed with grey cement slurry and pointed with white cement with admixture of pigment to match the shade of granite stone complete in skirting , cills and jambs on vertical surfaces over and including 15mm thick cement mortar 1:3 backing coat etc complete all as specified and directed.

Surface excavation n. exc 30 cm deep and averaging 15 cm deep and getting out in any type of soil complete all as specified and directed.

M & L 100 mm thick PCC (1:4:8) type D-2 using 40 mm graded stone agreegate as in sub base, complete all as specified and directed.

M&L for machine pressed precast concrete interlocking paver block with grey cement and pigment any shape and size confirming to IS 15658-2006 0f 60mm thickness, M-35 grade and laid over 50 mm with sand filling complete all as specified and diected. (Supply only sand will be measured and paid seperately)

Supply only Sand all as specified and directed

M&L for rendering 20 mm thick on other than fair faces of brick work or stone masonry surfaces in CM (1:4) finished even and smooth without using extra cement.

M&L for preparation plastared of new surfaces of wall and applying two coats of cement base paint over one coat primer all as per etc complete all as specified and directed

M&L for mild steel framed work of ornamental and intricate design such as in grills, etc doors or gates of angle or other sections with gusset plates, rails grills, etc with ends of bars shouldered and/or riveted, or for barred iron doors and small gates including pintel hinges and hold fasts etc and similar works conforming to Fe 410-W (Gde-E-250) quality-A

M&L writing letters or figures (Block Roman, Itali or Indian) n.exc 30cm high complete all as specified and directed.

S&F plain black mild steel sheet 0.63 mm thick fixed with self tapping screws as specified and directed by Engr-In-Charge.

Returning, filling in, including spreading, levelling, watering and well ramming in layers, not exceeding 25 cm (with soil) complete .

Removing excavated material/soil to a distance exc 250 meter and not exceding 500 meter depositing where directed,, complete all as specified and directed.

Removing surplus excavated material/ soil to a distance n exc 50 m and deposting where directed at a level n exc 1.5 m above the starting point complete all as directed.

S&F for rolled mild steel Fe 410-00 (Gde E-250) as in stanchions, rafters, purlins, etc completed all as specified and directed.

M&L for PCC (1:2:4) type B2 (using 40mm graded stone aggregrate) as in foundations, filling and mass concrete complete.

M&L for PCC (1:5:10) type E-2 (40mm graded aggregate) in foundation filling and mass concrete.

M&L for broken stone or boulders hardcore of guase n.exc 63 mm depositing, spread and levelled in layers not exc 15 cm thick, watered and rolled/rammed to a true surfaces, complete all as specified and directed.

M & L for 75 mm thick PCC (1:3:6) type C-2 (using 40 mm graded stone aggregate) in , plinth protection , including finishing the surface even and smooth without using extra cement.

M & L for Rendering 15 mm thick cement plaster on unfair brick work or concrete surfaces in CM 1:6 finished to even and smooth sitfaces in without using extra cement incl.

M & L for walling of random rubble stone masonry uncoursed well bounded badded and solidly hearted built in CM 1:6 brought upto coursed.

M & L for providing RCC (1:2:4) type B1 beams cantilevers , lintels etc using 20mm graded aggregates all as specified.

M&L TMT bars 10mm dia and over cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hookings ends and binding mild or securing with clips conform (Fe-410w or Fe-290) as specified.

M&L mild steel TMT 6mm to 8mm dia as in striups cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hookings ends and binding mild or securing with clips conform (Fe-410w or Fe-290) as specified.

M & L for Preparing new surfaces of walls by and applying three coat of white wash.

M & L for Non-skid ceramic coloured tiles 7 to 8mm thick (square/ rectangular) area of each tile exceeding 0.06sqm but not exceeding 0.11 sqm,in floor etc, set and jointed with neat cement slurry and pointed in white or coloured cement to match including 15mm thick screed bed for laying floor finish in CM 1:4 all as per directed and specified.

Coloured Glazed ceramic tiles 300 x 200 x 7 mm thick, on vertical surfaces such as skirting, dados and risers to steps etc., set and jointed in neat cement slurry and pointed in white or Coloured cement to match including 10mm thick plastering on wall surface to receive dado tiles in CM(1:4) as per directed and specified.

M & L for Solid PVC door frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S. square tube, suppling and fixing in opening as per specification .

S&f factory made solid panel PVC door shutter 30mm thick (style) consisting of frame made out of M.S tubes for top & bottom rails. M.S frame shall be covered with heat moulded plain colour PVC 'C' channel having a PVC sheet Strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap inser for top rail and bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S frame welded/sealed to the stiles & rails with suitable PVC sheet beading, and jointed togther with solvent cement, supplying & fixing in the frame at the site as pe specifcation

S&F Aluminium anodised bow handles of 150mm long fabricated type of extrded section fixed with screws to shutters complete all as specified and directed.

S & F 100 mm long medium weight, cold rolled mild steel Butt hinges.

S&F Aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet cast or extruded sections and fixing bolts and sliding bolts of extruded section or cast alluminium alloy and fixed of length of bolt 200 mm complete all as specified and directed.

S&F Aluminium anodised barrel tower bolt of extruded section150 mm long complete all as specified and directed.

S&F pre painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550mpa as in roof covering/clading to wall, fixed with self taping screws as specified.

S & F for PVC connections 15mm size with PTMT nuts of length 600mm.

S & F PVC valveless , syphonic action type flushing cistern, low level, white, with inlet, ball valve, float and handle including brackets.

S&F in repair wash down water closet (pedestal pattern) white and including plastic water closet seat cover as per reqd colour with flat bottom and cover and mild steel chromium plated or aluminium hinging device (excluding flushing cistern ) etc complete all as specified and directed..

M & L for Joist, channel, angle, or tee section, fixed independently, with out connecting plates etc ( cut to ordinary length) i.e. within 20mm of the length indicated, angle iron fabrication Erection and fixing

M&L 75mm dia PVC (SWR) floor trap, plane with grating including jointing with solvent cement.

S&F brass tubular towel rail 20mm dia 'D' type 60cm long between flanges

S&F Vitreous China Wash hand basin, white of size 550x 400mm excluding taps, waste chain and plug and porcelain stopper but including brackets,32mm waste fitting and waste pipe of 32 mm bore, brass, chromium plated for glazed ware wash basin and 15mm dia pillar taps chromium plated fancy type etc complete all as specified and directed.

S & F Vitreous china urinal, bowl type flat back of size 465 x 355 x 265 mm white (minimum), with grating and union for discharge pipe complete all as specified and directed .

Supply and fixing of 16 mm outer diameter CPVC pipes SDR 11 & Plain CPVC SDR 11 fittings (including special fittings i.e. brass elbow, brass tee, Male brass threaded adaptor, female threaded adaptor etc required for fixing of bib tap, stop valve with CPVC pipes) concealed in walls/ ceiling or laying in floors etc., also including cutting chases, grooves and making good the same in CM 1:3 after fixing of pipes / fittings, complete all as specified and directed.

Supply and fixing of CPVC pipes SDR 11 & Plain CPVC SDR 11 Fittings of size 20mm outer diameter (including special fittings (brass elbow, brass tee, Male threaded brass adaptor, female threaded brass adaptor etc required for fixing of bib tap , stop valve ) fixed on the surfaces of walls / ceiling /laying over floors , complete all as specified and directed

S&F of 1000 ltrs PVC Water storage tank (cylindrical vertical with closed top) in position all as specified in SRR Part - I.

S&F Pillar taps, cast copper alloy, with capstan heads, chromium plated, fancy type scerwed down high pressure, with or without lettered "Hot" or "Cold" with long screwed shanks and fly-nuts, screwed for iron pipe ane fixed.

S & F 15 mm bore bib taps, cast copper alloy fancy type chromium plated with crutch or butterfly handle, screwed for iron pipe or for brass ferrule and fixed .

S & F 15 mm bore Stop valves, cast copper alloy screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for union..

M&L for 18 to 20 mm thick Udaipur Green Slab (table rubbed and Polished) in urinal partition and WHB slab single piece as in using marble dust with admixture of pigment to match with the shade of stone slab, complete all as specified and directed.

S & F Anodised alluminium snap grid frame work size 605x605mm for false ceiling all as specified.

M & L for 12 mm thick perforated particle board / tiles for insulation and acoustic purposes, 60 x 60 cm in size, fixed with screws to timber frame work or with staples on snap grid in ceilings, flat or sloping complete all as specified and directed.

M & L for 4 mm thick Non Asbestos fibre cement building desginer boards fixed or laid/ insertyed to trimber/ GI/ aluminium frame, fixed in ceiling .

Supplying and laying salt glazed stone ware drain pipe grade 'A' 150mm bore laid on concrete bed and jointed complete all as specified and directed. Make Jai jalaram/Giraco/AG Karimji

Supplying and laying salt glazed stone ware drain pipe grade 'A' 100mm bore laid on concrete bed and jointed complete all as specified and directed. Make Jai jalaram/Giraco/AG Karimji

Excavating in post holes (or similar holes) in soft/loose soil each n.exc 0.5 cum, getting out, returning, filling in and ramming earth or broken rubble in layers n.exc 25cm watering and removing surplus soil to a distance n.exc 50m and making good surface complete all as specified and directed.

M&L for cement concrete 1:2:4 type B1 (using 20mm graded stone aggregate) of foundation for fixing tubular poles/trusses in columns, pillars etc complete all as specified.

S & F mild steel plates (Plain or chequered) channel square cut or notched (ordinary and counter sunk) forming holes, sithout any attachment for Fe-410-0 complete all as specified and directed by the Engr-in-Charge.

S & F Framed work as in tubular posts roof trusses, purlines, rafters etc made of tubes (square circular oval or any other shape or section as directed) including all necessary fittings, nut bolts, threading or welding etc as required for completion of work.

Surface dressing n. exc 15cm deep and getting out in soft/loose soil all as specified.

M & L for100 mm thick cement concrete 1:2:4 type 1 using 20mm graded aggregate all as specified.

M&L for post construction anti- termite traetment along the external wall below concreate or masonary apron using chemical emulsion @2.25 liters per linear meter including drilling and plugging holes with cement morter 1:2 to match the existng floor etc complete all as specified and directed.

M&L for post construction anti- termite of soil / concreate under existing floor along the floor and wall junction using chemical emulsion @ 1 liters per hole 300 mm apart including drilling and plugging 12 mm dia holes with cement morter 1:2 to match the existing floor etc complete all as specified and directed.

M&L for point wiring complete with proper colour coding using 1100 volts grade, 1.5 sqmm PVC insulated FRLS unsheathed wire with multi stranded copper conductor confirming to IS -694, part-II, ISI marked drawn in and including PVC rigid conduit of 20/25 not less than 25 mm fixed on the conceal of wall, celing etc complete with sunken iron pressed steel terminal box 2 mm thick for fitting mounting switch/ sockets regulators etc with hylam sheet 3 mm thick cover and with 1.5 sqmm PVC insulated copper conductor earth wire and connected to earth dolly for the following points all as specified and directed. Make of wire- Polycab/Finolex (a) One light point controlled by one switch

(b) One fan/exhaust fan point controlled by one switch

(c) One 3 pin socket point 5A controlled by switch on independent board

All as per item No 97 here-in-before but for 3 pin socket outlet 15 Amp independent with cable 2.5 sqmm unsheathed multistranded 1100 Volts grade complete with 1.5 sqmm PVC insulated earth wire and connecting to earth dolly all as specified and directed.

Supply and fix ceiling fan 1200 mm sweep 5 star rating with regulator including connection etc including provision of cable from ceiling rose to fan complete all as directed.Make- CG/Orient/Havells

S&F Exhaust fan 300 mm sweep, 230 volts and 1400 rpm heavy duty motor with necessary connection up including provision of cable from ceiling rose to exhaust fan including louvers complete all as specified (Make Orient/CG/Havells)

S&F LED fitting 36W 2'x2' CRCA LED panel recess mounted, powder coated, white, CRCA with flate white high transmission acrylic cover of make Bajaj Model No : BZRSQL 36W XL WH or equivalent of make Philips or CG as approved by the GE, including provision of 0.5 Sqmm 3 core flexible copper conductor wire for connecting from the ceiling rose, complete all as specified and directed.

S&F in repairs of LED indoor decorative aluminium extruded LED batted integrated type tube light fitting and including 1x18/20W, 230V (Not less than 18W), bipin holders, connector block etc complete with all accessories internally prewired and including connected up with twin core twisted flexible copper conductor cable with suitable sizes all as specified and directed. Make: PHILIPS Cat No BNO21C LED20S or equivalent of make Bajaj/ Wipro

S&F for switch, Piano flush type 5A single pole, one way, 230 V ISI marked complete all as specified Make- Anchor/Legrand/Roma

S&F Ceiling rose polycarbonate, isolated body three terminal 230 volts complete all as specified

S&F for switch socket multipurpose 5A flush type 2 in one (2pin & 3pin), 230V,50 Hz complete all as specified Make- Anchor/Legrand/Roma

S&F for switch socket universal type 15A flush type controlled by one switch with interlocking arrangement, 230V ISI marked complete all as specified Make- Anchor/Legrand/Roma

S&F TPN 8 way double door DB 415V, 50Hz including incomer as suitable MCCB 40 Amps three pole complete all as specified and directed. Make- Legrand/Havells/HPL

S&F MCB DB TPN 8 way double door 415V, 50 Hz incomer as suitable MCB as specified and directed. Make- Legrand/Havells/HPL

S&F MCB 40A rating, 2 Pole, 240 Volts all as specified and directed Make- Legrand/Havells/HPL

S&F MCB SP 6-32 Apms all as specified and directed.Make- Legrand/Havells/HPL

Supply, laying and testing cable XLPE Insulated , screened, PVC bedded, galvanized steel strip or wire armoured, electric power cables (heavy duty) 1100 Volts grade with stranded aluminium conductor of size 10.0 sq mm 2 core complete all as specified Make- Polycab/Havells

Supply and spreading sand in trenches as cushioning to under ground cable on top and bottom of cable all as specified.

Supply and laying un-reinforced pre cast concrete cable cover class LV type I flat of size 250 x 150mm 40mm.

M&L in repairs of GI pipe 40 mm dia light grade with all fittings for cable protection .

LUCKY DECOR

M/s. GULSHAN CONTRACTION

PANKAJ AND BROTHERS

joshua construction