Development and Improvement of Community Infrastructures at Low Income Settlements in Pondicherry Municipality, Puducherry. (Package 6)

Amount

Earthwork in excavation by mechanical means (Hydraulic excavator) / manual means in foundation trenches or drains (not exceeding 1.5m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, lift upto 1.5m, including getting out the excavated soil and disposal of surplus excavated soil as directed , within a lead of 50m - all kinds of soil

Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20cm in depth, consolidating each deposited layer by ramming and watering, lead upto 50m and lift upto 1.5m

Supplying and filling with gravel (excluding rock) in layers not exceeding 20cm in depth , breaking clods , watering , rolling each layer with 1/2 tonne roller , or wooden or steel rammers and rolling every 3rd and top-most layer with power roller of minimum 8 tonnes capacity including all leads and lift (Payment will be made based on level measurement)

Earth work in surface excavation not exceeding 30cm in depth but exceeding 1.5m in width as well as 10 sqm on plan including getting out and disposal of excavated earth up to 50m and lift up to 1.5m - All kinds of soil

Supplying and filling with gravel (excluding rock ) in trenches, plinth, sides of foundations etc. in layers not exceeding 20cm in depth consolidating each deposited layers by ramming and watering etc.complete including all lead and lift.

Clearing jungle including uprooting of rank vegetation, grass, brush wood, trees and saplings of girth upto 30cm measured at a height of 1m above ground level and removal of rubbish upto a distance of 50 m outside the periphery of the area cleared.

Close timbering in trenches including strutting, shoring and packing cavities (wherever required) complete (measurements to be taken of the face area timbered) .Depth exceeding 1.5m but not exceeding 3m

Supplying and filling in plinth with sand under floors including, watering, ramming consolidating and dressing complete.

Providing and fixing ISI marked aluminium butt hinges anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade with necessary screws etc.complete : 125x75x4mm

Providing and fixing aluminium tower bolts ISI marked anodised (anodic coating not less than grade AC 10 as per IS:1868) transparent or dyed to required colour or shade with necessary screws etc.complete : - 200x10mm

Providing and laying ceramic glazed floor tiles 300x300 mm (thickness to be specified by the manufacturer) of first quality conforming to IS: 15622 of approved make (Nitco / Kajaria ) in all colors, shades, except white, ivory, grey, fume red brown laid on 20mm thick bed of cement mortar 1:4 (1 cement : 4 coarse sand) including pointing the joints with white cement and matching pigments etc., complete.

Providing and fixing PVC corner beading of required size to suit the thickness of the wall tile at the corner joints of dado works

15mm cement plaster on the rough side of single or half brick wall of mix 1:5 (1 cement : 5 fine sand)

Painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade - Two or more coats on new work over an under coat of suitable shade with ordinary paint of approved brand and manufacure.

Excavation for roadwork in soil with hydraulic excavator of 0.9cum bucket capacity including cutting and loading in tippers, trimming bottom and side slopes, in accordance with requirements of lines, grades and cross sections and transporting to the embankment location with all lifts and lead upto 1000m.

Supply of Quarry rubbish including stacking to department gauge for premeasurement and spreading required thickness as directed by Engineer-in-charge.

Demolishing cement concrete manually / by mechanical means including disposal of material within 50 metres lead - nominal concrete 1:3:6 or richer mix (i/c equivalent design mix)

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - all work upto plith level - 1:1.5:3 (1 cement : 1.5 coarse sand : 3 graded stone aggregate 20mm nominal size)

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - all work upto plith level - 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20mm nominal size)

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - all work upto plith level - 1:4:8 (1 cement : 4 coarse sand : 8 graded stone aggregate 40mm nominal size)

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering.- All work upto plinth level -1:5:10 (1 cement:5coarse sand : 10 graded stone aggregate 40mm nominal size

Centring and shuttering including strutting , propping etc. and removal of form work for - foundations, footings, bases for columns

Providing and laying damp-proof course 50mm thick with cement concrete 1:2:4 (1 cement :2 coarse sand : 4 graded stone aggregate 20mm nominal size)

Extra for providing and mixing water proofing material in cement concrete work in doses by weight of cement as per manufacture's specification.

Applying a coat of residual petroleum bitumen of grade of VG-10 of approved quality using 1.7 kg per square metre on damp proof course after cleaning the surface with brushes and finally with a piece of cloth lightly soaked in kerosene oil.

Centring and shuttering including strutting , propping etc. and removal of form work for - columns, piers, abutments, pillars, posts and struts

Steel work welded in built up sections / framed work , including cutting,hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required - in gratings, frames, guard bar, ladder, railings, brackets, gates and similar works

Painting with synthetic enamel paint of approved brand and manufacture to give an even shade - Two or more coats on new work

Providing and fixing in position 12 mm thick bitumen impregnated fibre board conforming to IS : 1838 , including cost of primer , sealing compound in expansion joints

Cement concrete flooring 1:2:4 (1 cement :2 coarse sand : 4 graded stone aggregate) finished with a floating coat of neat cement including cement slurry, but excluding the cost of nosing of steps etc. complete. 40mm thick with 20mm nominal size stone aggregate

12mm cement plaster of mix -1:4 ( 1 cement : 4 fine sand)

Disposal of debries / surplus excavated earth including loading, unloading and conveyance to low lying areas within 2km lead as directed by the Engineer in charge.

Raising of various types of manholes and flushing tank by cutting alround the manhole cover, removing the frame and cover from the manhole by cutting the B.T., W.B.M., surface, raising the manhole to the equired height with brick work in cement motar 1:4 (One cement and four sand), refixing the frame in position by laying cement concrete 1:1.5:3 (One cement one and half sand and three 20mm HBG metal)including curing, but excluding the cost of reinforcement, finishing the top, inside and outside plastering with 20mm thick in cement mortar 1:3(one cement three sand), the rate includes all materials, providing barricading,caution board, watch and ward etc.,complete till the completion of work with minimum hindrance to the traffic.- 30cm height.

Providing and laying in position specified grade of reinforced cement concrete , excluding the cost of centering , shuttering , finsishing and reinforcement - All work upto plinth level 1:1.5:3 (1cement : 1.5 coarse sand : 3 graded stone aggregate 20 mm nominal size)

Providing , hoisting and fixing upto floor five level precast reinforced cement concrete work in string courses, bands, copings, bed plates, anchor blocks, plain window sills and the like, including the cost of required centering, shuttering but excluding cost of reinforcement , with 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20mm nominal size)

Providing and laying in position ready mixed M-25 grade concrete for reinforced cement concrete work , using cement content as per approved design mix , manufactured in fully automatic batching plant and transported to site of work in transit mixer for all leads , having continuous agitated mixer , manufactured as per mix design of specified grade for reinforced cement concrete work including pumping of R.M.C. from transit mixer to site of laying , excluding the cost of centering , shuttering , finishing and reinforcement including cost of admixtures in recommended proportions as per IS : 9103 to accelerate / retard setting of concrete , improve workability without impairing strenghth and durability - Note :- Cement content considered in this item is @ 330 kg / cum.Excess / less cement used as per design mix is payable / recoverable separately - All work upto plinth level

Providing and laying in position ready mixed M-25 grade concrete for reinforced cement concrete work , using cement content as per approved design mix , manufactured in fully automatic batching plant and transported to site of work in transit mixer for all leads , having continuous agitated mixer, manufactured as per mix design of specified grade for reinforced cement concrete work including pumping of R.M.C. from transit mixer to site of laying , excluding the cost of centering , shuttering , finishing and reinforcement including cost of admixtures in recommended proportions as per IS : 9103 to accelerate / retard setting of concrete , improve workability without impairing strenghth and durability - Note :- Cement content considered in this item is @ 330 kg / cum. Excess / less cement used as per design mix is payable / recoverable separately - All work above plinth level upto floor V level

Reinforced cement concrete work in beams , suspended floors, roofs having slope upto 15 degree landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases upto floor five level excluding the cost of centering, huttering,finishing and reinforcement with 1:2:4 (1 cement :2 coarse sand : 4 graded stone aggregate 20mm nominal size).

Reinforced cement concrete work in arches , archribs , domes , vaults , shells , folded plate and roofs having slope more than 15 degree upto floor five level excluding the cost of centering , shuttering , finishing and reinforcement with 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20mm nominal size)

Reinforced cement concrete work in vertical and horizontal fins individually or forming box louvers , facias and eaves boards upto floor five level excluding the cost of centering , shuttering , finishing and reinforcement , with 1:1.5:3 (1 cement : 1.5 coarse sand : 3 graded stone aggregate 20 mm nominal size)

Reinforced cement concrete work in walls (any thickness) , including attached pilasters, buttresses , plinth and sting courses , fillets , columns , pillars , piers , abutments , posts and struts etc. upto floor five level excluding cost of centering , shuttering , finishing and reinforcement - 1:1.5:3 (1 cement : 1.5coarse sand : 3graded stone aggregate 20mm nominal size)

Reinforced cement concrete work in beams ,suspended floors, roofs having slope upto 15 degree landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases upto floor five level excluding the cost of centering, shuttering,finishing and reinforcement with 1:1.5:3 (1 cement : 1.5 coarse sand : 3 graded stone aggregate 20mm nominal size

Providing precast cement concrete jali 1:2:4 ( 1 cement : 2 coarse sand : 4 graded stone aggregate 6mm nominal size) reinforced with 1.6 mm dia mild steel wire including centering and shuttering, roughening cleaning , fixing and finishing in cement mortar 1:3 ( 1 cement : 3 fine sand) etc. complete excluding plastering of the jambs, sills and soffits - 50mm thick

Centring and shuttering including strutting, propping etc.and removal of form for:Foundations , footings, bases of columns ,etc. for mass concrete.-

Centring and shuttering including strutting, propping etc.and removal of form for: suspended floors, roofs, landings , balconies and access platform -

Centering and shuttering including strutting , propping etc and removal of form for - Columns , Pillars , Piers , Abutments , Posts and Struts

Centering and shuttering including strutting , propping etc and removal of form for - Lintels , beams , plinth beams , girders , bressumers and catilevers

Centering and shuttering including strutting , propping etc and removal of form for - Arches , domes, vaults upto 6m span

Centering and shuttering including strutting , propping etc and removal of form for - Vertical and horizontal fins individually or forming box louvers band, facias and eaves boards

Centring and shuttering including strutting, propping etc. and removal of form for: Walls (any thickness) including attached pilasters, buttresses, plinth and string courses etc.

Steel reinforcement for R.C.C.work including straightening , cutting , bending , placing in position and binding all complete upto plinth level - Hard drawn steel wire

Steel reinforcement for R.C.C work including straightening , cutting , bending , placing in position and binding all complete upto plinth level - Thermo - Mechanically treated bars (TISCON / VIZAG / IISCO /SAIL / JSW) Fe - 415 or more

Steel reinforcement for R.C.C.work including straightening , cutting , bending , placing in position and binding all complete upto plinth level - Thermo -Mechanically treated bars (ISI BRAND OF APPROVED MAKE) Fe - 415 or more

Brick work with common burnt clay F.P.S. (non modular ) bricks of class designation 3.5 in foundation and plinth in - cement mortar 1:6 (1 cement : 6 coarse sand)

Half brick masonry with common burnt clay F.P.S. (non modular) bricks of class designation 3.5 in superstructure above plinth level upto floor V level - cement mortar 1:4 (1 cement : 4 coarse sand)

Brick work with common burnt clay F.P.S. (non modular ) bricks of class designation 3.5 in foundation and plinth in - cement mortar 1:4 (1 cement : 4 coarse sand)

Brick work with common burnt clay F.P.S (non modular ) bricks of class designation 3.5 in superstructure above plinth level upto floor five level in all shapes and sizes in - cement mortar 1:6 ( 1 cement : 6 coarse sand)

Half brick masonry with common burnt clay F.P.S. (non modular) bricks of class designation 3.5 in foundations and plinth in - cement mortar 1:4 (1 cement :4 coarse sand)

Extra for providing and placing in position 2 nos 6mm dia M.S.bars at every third course of half brick masonry

Providing, laying, spreading and compacting graded stone aggregate to wet mix macadam specification including remixing the material with water at OMC in mechanical mix plant carriage of mixed material by tipper to site, laying in uniform layers with paver in sub-base / base course on well prepared surface and compacting with vibratory roller to achieve the desired density - Using vibratory roller. (As per MoRTH specification, 4th Revision)

Raising manhole cover and frame slab to required level including dismantling existing slab and making good the damage as required (raising depth of manhole to be paid separately) Rectangular manhole 120x90 cm with circular cover 500 mm dia of grade MD-10.

Painting two coats after filling the surface with synthetic enamel paint in all shades on new plastered concrete surfaces.

Providing and fixing upto floor five level precast cement concrete solid block, inlcuding hoisting and setting in position with cement mortar 1:3 (1 cement : 3 coarse sand) cost of required centering,shuttering complete - 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20mm nominal size)

Providing and fixing stone jali 40 mm thick throughout in cement mortar 1:3 (1 cement : 3 coarse sand), including pointing in white cement mortar 1:2 (1 white cement : 2 stone dust) with an admixture of pigment, matching the stone shade , jali slab without any chamfers etc - red sand stone

Providing and laying Polished Granite stone flooring in required design and patterns , in linear as well as curvilinear portions of the building all complete as per the architectural drawings with 18mm thick stone slab over 20mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with cement slurry and pointing with white cement slurry admixed with pigment of matching shade including rubbing , curing and polishing etc, all complete as specified - Polished Granite stone slab jet Black , Cherry Red , Elite Brown , Cat Eye or equivalent

Providing wood work in frames of doors , windows, clerestory windows and other frames , wrought framed and fixed in position with hold fast lugs or with dash fasteners of required dia & length (hold fast lugs or dash fastener shall be paid for separately) -Padak wood

Providing and fixing panelled or panelled and glazed shutters for doors, windows, and clerestory windows, including ISI marked M.S.pressed butt hinges bright finished of required size with necessary screws, excluding panelling which will be paid for separately , all complete - Padak wood - 30 mm thick shutters

Providing and fixing panelling or panelling and glazing in panelled or panelled and glazed shutters for doors , windows and clerestory windows (area of opening for panel inserts excluding portion inside grooves or rebates to be measured). Panelling for panelled or panelled and glazed shutters 25 mm to 40 mm thick - Kiln seasoned and chemically treated Padak wood

Providing and fixing panelled or panelled and glazed shutters for doors, windows, and clerestory windows, including ISI marked M.S.pressed butt hinges bright finished of required size with necessary screws, excluding panelling which will be paid for separately , all complete - Kiln seasoned and chemically treated Vengai wood - 35 mm thick shutters thick

Providing and fixing ISI marked flush door shutters conforming to IS : 2202 (Part 1) decorative type , core of block board construction with frame of 1 st class hard wood and well matched teak 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters - 35 mm thick including ISI marked Stainless Steel butt hinges with necessary screws

Providing wood work in frames of doors windows, clerestory windows and other frames , wrought framed and fixed in position with hold fast lugs or with dash fasteners of required dia & length (hold fast lugs or dash fastener shall be paid for separately) -Vengai wood

Providing and fixing panelled or panelled and glazed shutters for doors, windows, and clerestory windows, including ISI marked M.S.pressed butt hinges bright finished of required size with necessary screws, excluding panelling which will be paid for separately , all complete - Vengai wood - 35 mm thick shutters

Providing and fixing glazed shutters for doors , windows and clerestory windows using 4 mm thick float glass panes including ISI marked M.S.pressed butt hinges bright finished of required size with necessary screws -Vengai wood - 35 mm thick

Providing and fixing panelled or panelled and glazed shutters for doors, windows, and clerestory windows, including ISI marked M.S.pressed butt hinges bright finished of required size with necessary screws, excluding panelling which will be paid for separately , all complete - Padak wood - 35 mm thick shutters

Providing and fixing panelling or panelling and glazing in panelled or panelled and glazed shutters for doors , windows and clerestory windows (area of opening for panel inserts excluding portion inside grooves or rebates to be measured). Panelling for panelled or panelled and glazed shutters 25 mm to 40 mm thick - Padak wood

Providing and fixing IS : 12817 marked stainless steel butt hinges (heavy weight) with stainless steel screws etc.complete - 100 x 60 x 2.50 mm

Providing and fixing factory made uPVC white colour casement /casement cum fixed glazed windows comprising of uPVC multi-chambered frame , sash and mullion (where ever required) extruded profiles duly reinforced with 1.60 + or - 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), uPVC extruded glazing beads of appropriate dimension , EPDM gasket , stainless steel (SS 304 grade) friction hinges , zinc alloy (white powder coated) casement handles, G.I fasteners 100 x8 mm size for fixing frame to finished wall , plastic packers , plastic caps and necessary stainless steel screws etc. Profile of frame & sash shall be mitred cut and fusion welded at all corners, mullion (if required) shall be also fusion welded including drilling of holes for fixing hardware's and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealent over backer rod of required size and of approved quality , all complete as per approved drawing.(Single / double glass panes and silicon sealent shall be paid separately) - Casement window double panels with S.S.friction hinges (350x19x1.9mm) made of (big series) frame 67 x 60 mm & sash / mullion 67 x 80mm both having wall thickness of 2.3 + or - 0.2 mm and single glazing bead /double glazing bead of appropriate dimension .(Area of window above 1.50 sqm)

Providing and fixing wooden moulded beading to door and window frames with iron screws , plugs and priming coat on unexposed surface etc. complete - Burma teak wood - 50 x 20 mm

Providing 40 X 5 mm flat iron hold fast 40 cm long including fixing to frame with 10 mm diameter bots, nuts and wooden plugs and embeddings in cement concrete block 30 x10 x 15 cm 1:3:6 mix (1 cement : 3 coarse sand : 6 graded stone aggregate 20mm nominal size)

Providing and fixing bright finished brass butt hinges with necessary screws etc complete - 125 X 85 X 5.5 mm (heavy type)

Providing and fixing bright finished brass butt hinges with necessary screws etc complete - 100 X 85 X 5.5 mm (heavy type)

Providing and fixing bright finished brass butt hinges with necessary screws etc complete - 75 x 40 x 2.5 mm (ordinary type)

Providing and fixing bright finished brass tower bolts (barrel type) with necessary screws etc complete - 250 x 10 mm

Providing and fixing bright finished brass tower bolts (barrel type) with necessary screws etc complete - 200 x 10 mm

Providing and fixing bright finished brass tower bolts (barrel type) with necessary screws etc complete - 100 X 10 mm

Providing and fixing bright finished brass 100 mm mortice latch and lock with 6 levers and a pair of lever handles of approved quality with necessary screws etc complete

Providing and fixing bright finished brass handles with screws etc complete - 125 mm

Providing and fixing bright finished brass handles with screws etc complete - 100 mm

Providing and fixing aluminium sliding door bolts , ISI marked , anodised ( anodic coating not less than grade AC 10 as per IS : 1868), transparent or dyed to required colour or shade , with nuts and screws etc complete - 300 X 16 mm

Providing and fixing aluminium hanging floor door stopper , ISI marked , anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour and shade with necessary screws etc complete - Twin rubber stopper

Providing and fixing of 65 mm Godrej Navatal lock of 7 levers with 3 keys etc complete

Providing and fixing IS : 12817 marked stainless steel butt hinges (heavy weight) with stainless steel screws etc.complete - 125 X 64 x 2.50 mm

Providing and fixing bright / matt finished Stainless Steel handles of approved quality & make with necessary screws etc all complete - 125 mm

Providing and fixing aluminium tower bolts , ISI marked , anodised (anodic coating not less than grade AC 10 as per IS :1868) , transparent or dyed to required colour or shade , with necessary screws etc. complete - 300 x10 mm

Providing and fixing IS : 12817 marked stainless steel butt hinges with stainless steel screws etc.complete - 100 x 58 x 1.90 mm

Providing and fixing aluminium handles , ISI marked , anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade,with necessary screws etc, complete - 125 mm

Providing and fixing aluminium handles , ISI marked , anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade,with necessary screws etc, complete - 75 mm

Providing and fixing of 65mm Godrej Navtal lock of 6 levers etc complete

Providing and fixing aluminium tower bolts ISI marked , anodised (anodic coating not less than grade AC 10 as per IS :1868) , transparent or dyed to required colour or shade , with necessary screws etc. Complete - 100 x10 mm

Providing and fixing ISI marked powder coating tower bolt black finish (Barrel type) with necessary screws etc.complete - 250 x10 mm

Providing and fixing ISI marked oxidised MS door latches conforming to IS : 5930 with screws etc.complete - 300 x20x6 mm

Providing and fixing bright finished 100 mm mortice lock with 6 levers without pair of handles of approved quality for aluminium door , with necessary screws etc complete

Providing and fixing facory made door frame (single rebate ) made out of single piece extruded solid PVC foam profile with homogenous fine cellular structure having smooth outer integral skin having 62 mm width & 32 mm thickness , frame will be mitred & jointed with self driven self tapping screws of size 38 mm x 4 mm & PVC solvent cement , including fixing the frame to wall with suitable dia & length anchor fastener as per manufacturer's specification

Providing and fixing factory made 30 mm thick door shutter made of solid PVC foam profile . The styles & rails shall be of size 75 mm X 30 mm having wall thickness 5 mm . The styles , top & bottom rails shall have one side wall thickness of 15 mm integarally extruded on the hinge side of the profile for better screw holding power. The styles and rails shall be reinforced with M.S. tubes of size 33 mm x 17 mm x 1 mm , painted with primer , all four corners of reinforcement to be welded or sealed . Solid PVC extruded bidding (push fit type) will be set inside the styles and the rails with a cavity, to recive single piece extruted 5 mm PVC sheet as panel. The styles and rails will be mitred cut and joint with the help of PVC solvent cement & self driven self tapping screws. Single piece extruded solid PVC lock rail of size 100 mm X 30 mm with wall thickness 5 mm & 15 mm integrally extruded in the middle of the lock rail & fixed with styles with the help of PVC solvent cement and self driven self tapping screws of size 100 mm x 8 mm complete as per manufacturer's specifications - Non decorative finish

Providing and fixing to existing door frames - 30 mm thick factory made Polyvinyl Chloride (PVC) door shutters made of styles and rails of a uPVC hollow section of size 60 x 30 mm and wall thickness 2 mm (+- 0.2 mm) with inbuilt decorative moulding edging on one side . The styles and rails mitred and joint at the corners by means of M.S. galvanised / plastic brackets of size 75 x 220 mm having wall thickness 1.0 mm and stainless steel screws. The styles of the shutter reinforced by inserting galvanised M.S.tube of size 25x20 mm and 1mm (+- 0.1mm) wall thickness. The lock rail made up of 'H' section, a uPVC hollow section of size 100 x 30 mm and 2 mm (+-0.2 mm) wall thickness, fixed to the shutter styles by means of plastic / galvanised M.S. 'U' cleats. The shutter frame filled with a uPVC multichambered single panel of size not less than 620 mm, having overall thickness of 20 mm and 1 mm (+_ 0.1mm) wall thickness. They panels filled vertcally and tie bar at two places by inserting horizontally 6 mm galvanised M.S.rod and fastened with nuts and washers, complete as per manufacturer's specification

Providing and fixing factory made P.V.C. door frame of size 50x47mm with a wall thickness of 5mm, made out of extruded 5mm rigid PVC foam sheet mitred at corners and joined with 2nos.of 150mm long brackets of 15x15mm M.S.square tube, the vertical door profiles to be reinforced with 19x19mm M.S.square tube of 19 gauge,EPDM rubber gasket weather seal to be provided through out the frame.The door frame to be fixed to the wall using M.S.screws of 65/100mm size complete as per manufacturers specification

Structural steel work riveted , bolted or welded in built up sections , trusses and framed work , including cutting, hoisting , fixing in position and applying a priming coat of approved steel primer all complete

Providing and fixing stainless steel (grade 304) railing made of hollow tubes, channels, plates etc., including welding ,grinding. Buffing, polishing and making curvature (whereever required) and fitting the same with necessary stainless steel nuts and bolts complte. i/c fixing the railing with necessary accessories & stainless steel dash fasteners, stainless steel bolts etc., of required size, on the top of the floor or the side of waist slab withsuitable arrangement (for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts,fasteners etc.,)

Steel work in built up tubular (round,square or rectanglar hollow tubes etc.) trusses etc., including cutting , hoisting,fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete - hot finished welded type tubes

Providing and laying 22 mm thick factory made pre-polished cement concrete flooring tiles of required colour and design over 20 mm thick cement mortar 1:4 (1 cement : 4sand ) and jointed with cement slurry mixed with an admixture of pigment to match the shade of the tile - (Endura \ Ultra \Dazzle \ Technic)

Kota stone slabs 20 mm thick in risers of steps , skirting , dado and pillars laid on 12 mm (average) thick cement mortar 1:3 (1cement :3 coarse sand) and jointed with grey cement slurry mixed with pigment to match the shade of the slabs,including rubbing and polishing complete

Providing and laying ceramic glazed floor tiles of size 300x300 mm (thickness to be specified by the manufacturer), of 1st quality conforming to IS : 15622, of approved make (Nitco / Kajaria) in colours such as white, Ivory, Grey, Fume red brown ,laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand), including pointing the joints with white cement and matching pigment etc., complete

Providing and fixing commercial quality ceramic glazed wall tiles conforming to IS : 15622 (thickness to be specified by the manufacturer) , of approved make (Jhonson / Asian / Somany / Nitco) in all colours , shades of size 300 x 600 mm as approved in skirting , risers of steps and dados, over 12mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand ) and jointing with grey cement slurry @ 3.3 kg per sqm, including pointing in white cement with pigment of matching shade complete - size 300x600 mm

Providing and laying fully vitrified floor tiles of size 600 x600 mm (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS : 15622 of approved make (Nitco / Rak / Johnson /Asian ) in all colours and shades , laid on 20 mm thick cement mortar 1:4 (1 cement : 4 coarse sand) , including grouting the joints with white cement and matching pigments etc., complete - size of tile 600 x600 mm

Providing and laying ceramic glazed floor tiles of size 300 x 300 mm (thickness to be specified by the manufacturer) , of commercial quality conforming to IS :15622, of approved make (Bell / Johnson / Regency / Somany / Naveen / Asian) in all colours, shades, except white , ivory, grey, fume red brown, laid on 20 mm thick bed of cement mortar 1:4 (1 cement : 4 coarse sand), including pointing the joints with white cement and matching pigments etc., complete

Providing and fixing 1st quality ceramic glazed wall tiles conforming to IS : 15622 (thickness to be specified by the manufacturer) , of approved make (Jhonson / Asian / Somany / Nitco) in all colours , shades of size 300 x 450 mm as approved in skirting , risers of steps and dados, over 12mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand ) and jointing with grey cement slurry @ 3.3 kg per sqm, including pointing in white cement with pigment of matching shade complete - size 300x450 mm

Providing and fixing 1st quallity ceramic glazed wall tiles conforming to IS : 15622 (thickness to be specified by the manufacture of approved make (Jhonson / Asian / Somany / Nitco) in all colours, shades of size 200 x 300 mm as approved in skirting, risers of steps and dados over 12mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3 kg per sqm. Including pointing in white cement mixed with pigment of matching shade complete. - size 200x300mm

52 mm thick cement concrete flooring with concrete hardener topping , under layers 40mm thick cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20mm nominal size) and top layer 12 mm thick cement hardener consisting of mix 1:2 (1 cement hardener mix : 2 graded stone aggregate 6mm nominal size) by volume,hardening compound mixed @ 2 litre per 50 kg of cement or as per manufacturer's specification . This includes cost of cement slurry, but excluding the cost of nosing of steps etc.complete

Providing and laying vitrified tiles of size 600 x600 mm (thickness to be specified by manufacturer), with water absorption less than 0.08% and conforming to IS : 15622 , of approved make , in all colours & shade, in skirting ,riser of steps , over 12 mm thick bed of cement mortar 1:3 (1 cement :3 coarse sand), including grouting the joint with white cement & matching pigments etc.complete - size of tile 600x600mm

Painting top of roofs with bitumen of approved quality @ 17kg per 10 sq.m impregnated with a coat of coarse sand at 60cudm per 10 sq.m including cleaning the slab surface with brushes and finally with a piece of cloth lightly soaked in kerosene oil complete - with residual type petroleum bitumen of grade VG-10

Providing and laying pressed clay tiles (as per approved pattern 18mm nominal thickness of approved size) on roofs jointed with cement mortar 1:4 (1 cement : 4 coarse sand) mixed with 2% integral water proofing compound , laid over a bed of 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand) and finished neat complete

Lime concrete terracing on roofs of nominal size brick aggregate and 50% lime mortar 1:2 (1 lime putty : 2 surkhi) rammed and finished with gur and belgiri treatment complete including rounding of junctions with Parapet wall complete

Providing & fixing UV stabilised fibre glass reinforced plastic sheet roofing upto any pitch, including fixing with polymer coated 'J' or 'L' hooks, bolts & nuts 8mm dia G.I.plain / bitumen washers complete but excluding the cost of purlins , rafters ,trusses etc. The sheets shall be manufactured out of 2400 TEX panel rovigs incorporting minimum 0.3% ultra -voilet tabiliser in resin system under approximately 2400 psi and hot cured. They shall be of uniform pigmentation and thickness without air pockets and shall conform to IS 10192 and IS 12866. The sheets shall be opaque or translucent, clear or pigmented , textured or smooth as specified - 2mm thick corrugated (2.5" or 4.2 " or 6") or step-down (2" or 3" or 6") as specifed

Making khurras 45x45cm with average minimum thickness of 5 cm cement concrete 1:2:4 (1cement : 2 coarse sand : 4 graded stoneaggregate of 20mm nominal size) over P.V.C.sheet 1m x1m x 400 micron , finished with 12 mm cement plaster 1:3 ( 1cement : 3coarse sand) and a coat of neat cement ,rounding the edges, making and finishing the outlet complete

Providing and fixing on wall face unplasticised rigid PVC rain water pipes conforming to IS: 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10mm gap for thermal expansion, (i) Single socketed pipes - 110 mm diameter

Providing and fixing on wall face unplasticised - PVC moulded fittings / accessories for unplasticised rigid PVC rain water pipes conforming to IS:13592 Type A, including jointing with seal ring conforming to IS: 5382, leaving 10mm gap for thermal expansion - bend 87.5 degree - 110 mm bend

Providing and fixing on wall face unplasticised - PVC moulded fittings /accessories for unplasticised rigid PVC rain water pipes conforming to IS:13592 Type A, including jointing with seal ring conforming to IS: 5382, leaving 10mm gap for thermal expansion - Single tee without door -110x110x110mm

Providing and fixing on wall face unplasticised - PVC moulded fittings /accessories for unplasticised rigid PVC rain water pipes conforming to IS:13592 Type A, including jointing with seal ring conforming to IS: 5382, leaving 10mm gap for thermal expansion - shoe (plain) - 110mm shoe

Providing and fixing unplasticised - PVC pipe clips of approved design to unplasticised- PVC rain water pipes by means of 50x50x50mm hard wood plugs , screwed with M.S. screws of required length, including cutting brickwork and fixing in cement mortar 1:4 ( 1 cement : 4 coarse sand) and making good the wall etc., complete - 110mm

15mm cement plaster on the rough side of single or half brick wall of mix - 1:4 (1cement : 4 fine sand)

Extra for plastering done on moulding cornices or architraves including neat finish to line and level - in two coats

Providing and applying ready mixed wall putty (JK / Birla) of 2 mm thickness over plastered surface to prepare the surface even and smooth complete

White washing with lime to give an even shade - new work (three or more coats)

Finishing with deluxe multi surface paint system for interiors and exteriors using primer as per manufacture's specification - Two or more coats applied on walls @ 1.25 ltr / 10 sqm over and including one coat of special primer applied @ 0.75 ltr / 10 sqm

Painting wood work with deluxe multi surface paint of required shade. Two or more coat applied @0.90 ltr / 10sqm over an under coat of primer applied @ 0.75 ltr /10 sqm of approved brand and manufacure

Painting steel work with deluxe multi surface paint to give an even shade. Two or more coat applied @ 0.90 ltr / 10 sqm over an under coat of primer applied @ 0.80 ltr / 10 sqm of approved brand and manufacture

12mm cement plaster of mix -1:6 ( 1 cement : 6 fine sand)

Extra for plastering done on moulding cornices or architraves including neat finish to line and level - in one coat

18mm thick moulded cement mortar band in two coats under layer 12mm thick with re cement mortar 1:5 (1 cement : 5 coarse sand) top layer 6mm thick with cement mortar 1:4 (1 cement : 4 fine sand)

Applying one coat of water thinnable cement primer of approved brand and manufacturer on wall surface - water thinnable cement primer

Finishing with epoxy paint (two or more coats) at all locations prepared and applied as per manufacturer's specifications including appropriate priming coat, preparation of surface , etc.complete - on concretel work

Applying priming coat - with ready mixed red oxide zinc chromate primer of approved brand and manufacture on steel galvanised iron / steel works

Applying priming coat - with ready mixed pink or grey primer of approved brand and manufacture on wood work (hard and soft wood)

Providing and fixing gun metal gate valve with C.I.wheel of approved quality (Screwed end) - 40mm nominal bore

Constructing brick masonry open surface drain with class designation 35 in cement mortar 1 : 4 (1 cement : 4 fine sand) including earth excavation, 10 cm thick bed concrete 1 : 5 : 10 (1 cement : 5 fine sand : 10 graded stone aggregate 40 mm nominal size and 25 mm thick cement concrete 1 : 2 : 4 (1 cement : 2 coarse sand : 4 graded stone aggregate 12.5 mm nominal size) for filling haunches including 12 mm cement plaster 1 : 4 (1 cement : 4 coarse sand) with a floating coat of neat cement inside the drain, its top and exposed side including disposal of surplus earth complete as per standard design - 15 cm drain 20 cm average depth - with brick class designation 35.

Providing and fixing square - mouth S.W.gully trap class SP -1 complete with C.I. grating brick masonry chamber with water tight C.I.cover with frame of 300 x300 mm size (inside) the weight of cover to be not less than 4.50kg and frame to be not less than 2.70 kg as per standard design - 100x100mm size P type - with sewer bricks conforming to IS :4885

Constructing brick masonry manhole in cement mortar 1:4 (1 cement : 4 coarse sand) with R.C.C. top slab with 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20 nominal size ), foundtion concrete 1:4:8 mix ( 1 cement : 4 coarse sand : 8 graded stone aggregate 40 mm nominal size), inside plastering 12 mm thick with cement mortar 1:3 (1cement : 3 coarse sand) finished with floating coat of neat cement and making channels in cement concrete 1:2:4 ( 1 cement : 2 coarse sand : 4 graded stone aggregate 20mm nominal size)finished with a floating coat of neat cement complete as per standard design - inside size 120x90 cm and 90cm deep including C.I.cover with frame ( heavy duty) 560 mm internal diametre, total weight of cover and frame to be not less than 208kg (weight of cover108 kg and weight of frame 100 kg) - with sewer bricks conforming to IS : 4885

Providing and fixing on wall / column face unplasticed - PVC soil and waste pipes (type - B) conforming to IS : 13592- 1992 including jointing with seal ring conformation to IS : 5382 leaving 10mm gap for thermal expansion - single socked pipes -110mm diametre

Providing and fixing on wall / column face unplasticised - PVC soil and waste pipes (type B) conforming to IS :13592 - 1992 including jointing with seal ring conforming to IS : 5382 leaving 10mm gap for thermal expansion - Single socketed pipes 75mm diameter

Providing and fixing on wall face / column face unplasticised - PVC moulded fittings /accessories for unplasticisd - PVC soil and waste pipes conforming to IS : 14735 -1999 including jointing with seal ring conforming to IS : 5382 leaving 10mm gap for thermal expansion - Single tee with door - 110 x110x110 mm

Providing and fixing on wall face / column face unplasticised - PVC mould fittings /accessories for unplasticisd - PVC soil and waste pipes conforming to IS : 14735 - 1999 including jointing with seal ring conforming to IS : 5382 leaving 10mm gap for thermal expansion - bend 110 mm

Providing and fixing on wall / column face unplasticisd - PVC moulded fittings /accessories for unplasticisd - PVC soil and waste pipes conforming to IS :14735 -1999 including jointing with seal ring conforming to IS : 5382 leaving 10mm gap for thermal expansion - Bend 75 mm

Providing and fixing ASTM pipes including all ASTM plain& brass threaded fittings i/c fixing the pipe with clamps at 1.00m spacing . This includes jointing of pipes & fitting with one step ASTM solvent cement and testing of joints complete (Internal work exposed on wall ) - 20mm nominal outer dia pipes

Providing and fixing ASTM pipes including all ASTM plain& brass threaded fittings i/c fixing the pipe with clamps at 1.00m spacing . This includes jointing of pipes & fitting with one step ASTM solvent cement and testing of joints complete (Internal work exposed on wall ) - 25mm nominal outer dia pipes

Providing and fixing ASTM pipes including all ASTM plain& brass threaded fittings i/c fixing the pipe with clamps at 1.00m spacing . This includes jointing of pipes & fitting with one step ASTM solvent cement and testing of joints complete (Internal work exposed on wall ) - 32mm nominal outer dia pipes

Providing and fixing ASTM pipes including all ASTM plain& brass threaded fittings i/c fixing the pipe with clamps at 1.00m spacing . This includes jointing of pipes & fitting with one step ASTM solvent cement and testing of joints complete (Internal work exposed on wall ) - 40mm nominal outer dia pipes

Providing and fixing C.P.brass bib cock of approved quality conforming to IS: 8931 -15 mm nominal bore

Providing and fixing water closet squatting pan (Indian type W.C.pan) with 100 mm Sand Cast Iron P or S trap, 10 litre low level white P.V.C flusing cistren, including flush pipe , manually controlled device (handle lever) conforming to IS : 7231 , with all fittings and fixtures complete , including cutting and making good the walls and floors wherever required. Stainless steel AISI -304 (18/8) Orissa pattern W.C.pan of size 585 x 480 mm with flush pipe and integrated type foot rests

Providing and fixing white vitreous china pedestal type water closet (European type W.C.pan) with seat and lid, 10 litre low level white P.V.C. flusing cistern, including flush pipe, with manually controlled device (handle lever), conforming to IS: 7231,with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required - W.C. pan with ISI marked white solid plastic seat and lid

Providing and fixing wash basin with C.I. brackets, 15mm C.P. brass pillar taps ,32mm C.P.brass waste of standard pattern ,including painting of fittings and brackets ,cutting and making good the walls wherever required - white Vitreous China wash basin size 630x450 mm with a pair of 15 mm C.P.brass pillar taps

Providing and fixing Stainless steel AISI 304 (18/8) kitchen sink as per IS 13983 with C.I.brackets and stainless steel plug 40mm , including painting of fittings and brackets, cutting and making good the walls wherever required - kitchen sink with drain board - 510x1040 mm bowl depth 250mm

Providing and fixing mirror of superior glass (of approved quality) and of required shape and size with plastic moulded frame of approved make and shade with 6mm thick hard board backing - rectangular shape 1500 x 450 mm

Providing and fixing PTMT towel rail complete with brackets fixed to wooden cleats with CP brass screws with concealed fitting arrangement of approved quality and colour - 600 mm long towel rail with total length of645 mm, 78 mm wide and effective height of 88mm, weighing not less than 190 gms

Providing and fixing water meter and stop cock in 25mm G.I pipe line including cutting and threading the pipe, making long screws, bolts, nuts, rubber insertions and testing the water meter etc. complete.

Providing and fixing gun metal gate valve with C.I.wheel of approved quality (Screwed end) - 32mm nominal bore

Providing and fixing PTMT Ball cock of approved quality colour and make complete with Epoxy coatd aliminium rod with L.P /H.P.H.D.plastic ball - 20 mm nominal bore, 120 mm long, weighing not less than 198 gms

Providing and fixing PTMT Ball cock of approved quality colour and make complete with Epoxy coatd aliminium rod with L.P / H.P.H.D.plastic ball - 25 mm nominal bore, 152 mm long, weighing not less than 440 gms

Providing and fixing PTMT Ball cock of approved quality colour and make complete with Epoxy coatd aliminium rod with L.P / H.P.H.D.plastic ball - 40 mm nominal bore, 206 mm long, weighing not less than 690 gms

Providing and fixing ball valve (brass) of approved quality , high or low pressure ,with plastic floats complete - 25mm nominal bore

Providing and fixing PTMT grating of approved quality and colour - rectangular type with openable cirucular lid - 150mm nominal size square 100mm diametre of the inner hinged round grating

Providing and fixing PTMT Soap dish holder having length of 138 mm , breadth 102 mm, height of 75mm with concealed fitting arrangements , weighing not less than 106 gms

Providing and fixing PTMT extension nipple for water tank pipe, fittings of approved quality and colour - 20mm nominal bore , weighing not less than 40 gms

Providing and placing on terrace (at all floor levels) polyethylene water storage tank ISI: 12701 marked , with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank - Circular Tank

Providing and fixing white vitreous china flat back or wall corner type lipped front urinal basin of 430x 260x350 mm and 340x410x265mm sizes respectively with automatic flusing cistern with standard flush pipe and C.P. brass spreaders with brass unions and G.I.clamps complete, including painting of fittings and brackets, cutting and making good the walls and floors wherever required - One urinal basin with 5 litre white P.V.C.automatic flusing cistern

Providing and fixing suitable size threaded mild steel cap or spot welded plate to the top of bore well housing /casing pipe,removable as pre requirement , all complete for borewell of - 200 mm dia

Making earth pit of G.I. pipe for earthing in earth pit with 40mm dia. G.I. pipe medium class of length 3.05m perforated with 46 Nos of 12mm dia. holes, pipe lowered in bore holes of 150mm dia. and filled in with charcoal and salt in alternative layer of 300mm, the top of G.I.pipe shall be clamped. Earth pit shall be provided with 60cm dia precast ring with 60cm depth alround,covered with R.C.C. precast slab etc. as per I.E. standards.

Providing and fixing of fire safety equipments comprising 1 No. of 4.5 kg of CO2 fire extinquisher 1m x 2m x6mm thick rubber mat shock proof of superior quality with two numbers of 10 litres capacity fire buckets (red colour) with M.S. stand arrangements etc.

Constructing brick masonry manhole with 35 class designation bricks in cement mortar 1:4 (1 cement : 4 coarse sand ) R.C.C. top slab with 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size), foundation concrete 1:4:8 mix (1 cement : 4 coarse sand : 8 graded stone aggregate 40 mm nominal size) inside plastering 12 mm thick with cement mortar 1:3 (1 cement : 3 coarse sand ) finished with a floating coat of neat cement and making channels in cement concrete 1:2:4 (1cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) finished with a floating coat of nean cement complete as per standard design - inside size 120 x 90 cm and 90 cm deep including C.I. cover with frame (medium duty) 500 mm internal diameter, total weight of cover and frame to be not less than 116 kg. (weight of cover 58 kg. and weight of frame 58 kg) - with bricks of class designation 35.

Cutting open concrete road for laying water main/sewer lines & stacking the usable materials on road side for reuse in road works.

Earth work excavation above water level and depositing on bank in sandy silt or other soil, wet sand or silt, light black cotton soil or clay, sandy loam and ordinary soil for I.C's manhole, well, infiltration, suction well including driving shoring materials etc., for excavation purpose and removing the shoring materials and refilling the trenches with excavated earth complying with standard specifications etc., complete.For first depth of 2 metres (using open timbering)

supplying and fixing C.I. cover without frame for manholes - 455 x 610 mm rectangular C.I. cover (light duty) the weight of the cover to be not less than 23 kg.

Supplying fixing and commisioning of Suguna / Texmo / Sharp 2 HP monoblock pumpset slow speed single phase motor. The rate include the cost of pumpset , pumpset fixing in position and test run etc.complete

Providing, laying and jointing UPVC pipes(Finolex / jain / Supreme / Truebore /Nandi) (1 Mpa)conforming to IS specification 4985 and ISI marked including transportation to the site ,lowering to the trenches, laying to proper grade and alignment, testing of joints with required testing equipment,including cost of solvent cement,excluding UPVC specials such as bends, tees, threaded pieces, couplers, reducer, endcaps etc.,complete all as per IS and CPWD specification. - 160mm dia.

Providing and fixing Anodised aluminium , minimum anodic coating of grade AC 15 grill of required pattern / design over the doors, windows and ventilators etc., including fixing (but excluding the cost of the sections, which will be paid separately)

Providing and fixing 12 mm thick frameless toughened glass door shutter of approved brand and manufacture , including providing and fixing top & bottom pivot & spring type fixing arrangement and making necessary holes etc. for fixing required door fittings, all complete (Door handle, lock and stopper etc. to be paid separately)

Providing and fixing on wall face unplasticised - PVC moulded fittings /accessories for unplasticised rigid PVC rain water pipes conforming to IS:13592 Type A, including jointing with seal ring conforming to IS: 5382, leaving 10mm gap for thermal expansion - bend 87.5 degree - 75mm bend

Providing and fixing gun metal gate valve with C.I.wheel of approved quality (screwed end) - 20 mm nominal bore

Providing and fixing brass bib cock of approved quality - 15mm nominal bore

Providing and fixing Stainless steel AISI 304 (18/8) kitchen sink as per IS 13983 with C.I.brackets and stainless steel plug 40mm , including painting of fittings and brackets, cutting and making good the walls wherever required - kitchen sink with drain board - 510x1040 mm bowl depth 225mm

Supplying fixing and commisioning of Suguna / Texmo / Sharp 1 HP monoblock pumpset slow speed single phase motor. The rate include the cost of pumpset , pumpset fixing in position and test run etc.complete

Extra for using coloured W.C.pan instead of white W.C.pan - Orissa pattern W.C.pan 580x440mm

Providing and fixing white vitreous china pedestal type water closet (European type) with seat and lid,10 litre low level white vitreous china flushing cistern & C.P.flush bend with fittings & C.I. brackets , 40 mm flush bend , overflow arrangement with specials of standard make and mosquito proof coupling of approved municipal design complete, including painting of fittings and brackets , cutting and making good the walls and floors wherever required - W.C.pan with ISI marked white solid plastic seat and lid

Providing, laying and jointing UPVC pipes(Finolex / jain / Supreme / Truebore / Nandi) (0.6 Mpa)conforming to IS specification 4985 and ISI marked including transportation to the site , lowering to the trenches, laying to proper grade and alignment, testing of joints with required testing equipment,including cost of solvent cement,excluding UPVC specials such as bends,tees, threaded pieces, couplers, reducer, endcaps etc., complete all as per IS and CPWD specification. - 110mm dia.

Providing and fixing in position UPVC moulded equal Tee (Finolex / jain)(1 Mpa) conforming to IS 7834 part II and ISI marked,including labour charges for jointing, jointing materials etc,complete - 110mm dia

Providing and fixing in position UPVC fabricated bend (Finolex / jain)(0.4 Mpa) conforming to IS 7834 part II and ISI marked,including labour charges for jointing, jointing materials etc,complete - 110 mm dia

Providing and fixing trap of self cleansing design with screwed down or hinged grating with or without vent arm complete, including cost of cutting and making good the walls and floors - 100mm inlet and 100mm outlet - sand cast iron S&S as per IS: 3989

Proviing and fixing ferrule coforming to IS 2692 and ISI marked along with test cetificate,including labour charges for drilling,cutting,threading,fixing in distribution pipes etc.,complete -20mm dia

Providing and fixing mild steel bracket including bolts,nuts,rubber insertion, labour charges etc,complete-80 x 40mm dia

Fixing water meter and stop cock in G.I.pipe line including cutting and threading the pipe and making long screws etc.complete (cost of water meter and stop cock to be paid separately)

Supplying and fixing of meter board of size 600mmx900mmx150mm on suitable angle frame with suitable water proof plywood 12mm thick for receiving ED supply. The board frame shall be painted and covered on all sides by 16 gauge M.S. sheet and fixed with 3 Nos. of 100 Amps fuse carrier (Havells /Standard/ Anchor make) with screws etc., complete.

Providing and fixing mirror of superior glass (of approved quality) and of required shape and size with plastic moulded frame of approved make and shade with 6mm thick hard board backing - circular shape 450 mm dia

Providing and fixing PTMT towel rail complete with brackets fixed to wooden cleats with CP brass screws with concealed fitting arrangement of approved quality and colour - 450 mm long towel rail with total length of 495 mm, 78 mm wide and effective height of 88mm, weighing not less than 170 gms

Constructing masonry chamber 90x90x100 cm inside, in brick work in cement mortar 1:4 (1 cement : 4 coarse sand) for sluice valve, with C.I.surface box 100mm top diameter, 160 mm bottom diameter and 180 mm deep (inside) with chained lid and RCC top slab 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20mm nominal size), i/c necessary excavation, foundation bricks of class designation 7.5 concrete 1:5:10 (1 cement : 5 fine sand: 10 graded stone aggregate 40mm nominal size) and inside plastering with cement mortar 1:3 (1 cement : 3 coarse sand) 12mm thick finished with a floating coat of neat cement complete as per standard design - with common burnt clay F.P.S. (non modular)

Providing and fixing PVC switch lock of 100mm length for aluminium sliding windows

Providing and fixing aluminium handle with lock of 75mm dia with necessary screws

Providing and fixing white vitreous china flat back or wall corner type lipped front urinal basin of 430x 260x350 mm and 340x410x265mm sizes respectively with automatic flusing cistern with standard flush pipe and C.P. brass spreaders with brass unions and G.I.clamps complete, including painting of fittings and brackets, cutting and making good the walls and floors wherever required - Range of four urinal basins with 10 litre white P.V.C. automatic flushing cistern

Lettering with black japan paint of approved brand and manufacture

Providing and fixing on wall face unplasticised - PVC moulded fittings / accessories for unplasticised rigid PVC rain water pipes conforming to IS:13592 Type A, including jointing with seal ring conforming to IS: 5382, leaving 10mm gap for thermal expansion - Single tee with door - 110x110x110mm

6 mm cement plaster 1:3 (1 cement : 3 fine sand) finished with a floating coat of neatcement and thick coat of lime wash on top of walls when dry for bearing of R.C.C. slabs and beams

Laying of under ground cable direct in ground including metal road cutting,excavation of earth, sand cushion, brick protection, back filling etc., complete. - upto 50 sqmm

Providing and fixing white vitreous china water closet squatting pan (Indian type) - Orissa pattern W.C.pan of size 580x440mm

Providing and fixing white vitreous china flat back or wall corner type lipped front urinal basin of 430x260x350mm or 340x410x265mm sizes respectively

Providing and fixing 600x450 mm beveled edge mirror of superior glass (of approved quality) complete with 6mm thick hard board ground fixed to wooden cleats with C.P.brass screws and washers complete

Providing and fixing in position pre-cast R.C.C. manhole cover and frame of required shape and approved quality - MD -10 - square shape 450 mm internal dimensions

Providing and fixing brass gate valve with C.I. wheel of approved quality (screwed end) - 32mm nominal bore.

Providing and fixing brass gate valve with C.I. wheel of approved quality (screwed end) - 20mm nominal bore.

Providing and fixing PTMT towel ring trapezoidal shape 215 mm long, 200mm wide with minimum distances of 37 mm from wallface with concealed fittings arrangement of approved quality and colour, weighing ot less than 88 gms

Providing, laying and jointing UPVC pipes(Finolex / jain / Supreme / Truebore / Nandi) (1 Mpa)conforming to IS specification 4985 and ISI marked including transportation to the site , lowering to the trenches, laying to proper grade and alignment, testing of joints with required testing equipment,including cost of solvent cement, UPVC specials such as bends, tees, threaded pieces, couplers, reducer, endcaps etc., complete all as per IS and CPWD specification. - 25mm dia.

Providing, laying and jointing UPVC pipes(Finolex / jain / Supreme / Truebore / Nandi) (1 Mpa)conforming to IS specification 4985 and ISI marked including transportation to the site , lowering to the trenches, laying to proper grade and alignment, testing of joints with required testing equipment,including cost of solvent cement,UPVC specials such as bends, tees, threaded pieces,couplers, reducer, endcaps etc., complete all as per IS and CPWD specification. - 32mm dia.

Demolishing R.C.C work manually / by mechanical means including stacking of steel bars and disposal of unserviceable material within 50 metres lead

Taking out doors, windows and clerestory window shutters (steel or wood) including stacking within 50 metres lead - of area 3 sqm and below

Demolishing brick work manually / by mechanical means including stacking of serviceable material and disposal of unserviceable material within 50 metres lead - in cement mortar

Providing and fixing finished brass hard drawn hooks and eyes -100mm

6mm cement plaster of mix 1:3 (1 cement : 3fine sand)

Providing and fixing C.P.brass long body bib cock of approved quality conforming to IS standards and weighing not less than 690 gms - 15 mm nominal bore

Constructing masonry chamber 60x60x75 cm inside , in brick work in cement mortar 1.4 (1 cement : 4 coarse sand) for sluice valve, with C.I.surface box 100 mm top diametre, 160mm bottom diametre and 180mm deep (inside) with chained lid and RCC top slab 1:2:4 mix (1cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) , i/c necessary excavation , foundation concrete 1:5:10 (1 cement : 5 fine sand : 10 graded stone aggregate 40mm nominal size) and in side plastering with cement mortar 1:3 (1 cement : 3 coarse sand) 12mm thick , finished with a floating coat of neat cement complete as per standard design - with common burnt clay F.P.S (non modular) bricks of class designation 7.5

Providing and fixing 100mm sand cast iron grating for gully trap

Providing and fixing white vitreous china pedestal type (European type / wash down type ) water closet pan

Providing and fixing P.V.C.low level flushing cistern with manually controlled device (handle lever) conforming to IS:7231, with all fittings and fixtures complete - 10 litre capacity -white

Dismantling tile work in floors and roofs laid in cement mortar including stacking material within 50 metres lead - for thickness of tiles 10mm to 25mm

Dismantling W.C.Pan of all sizes including disposal of dismantled materials i/c malba all complete

Printing new letters and figures of any shade with synthetic enamel paint black or per letter any other approved colour to give an even shade - Hindi

Providing and fixing wash basin with CI brackets, 15mm CP brass pillar taps 32 mm CP brass waste of standard pattern including painting of fittings and brackets, cutting and making good the walls wherever required Stainless steel AISI - 304 (18/8) wash basin 530x345mm with single 15mm CP brass pillar tap

Providing and fixing toilet paper holder C.P.brass

Providing and fixing ASTM pipes including all ASTM plain & brass threaded fittings i/c fixing the pipe with clamps at 1.00m spacing. This includes jointing of pipes & fitting with one step ASTM solvent cement and the cost of cutting chases and making good the same including testing of joints complete (Concealed work including cutting chases and making good the walls etc.) - 32mm nominal outer dia pipes

Providing and fixing ASTM pipes including all ASTM plain & brass threaded fittings this included jointing of pipes & fittings with one step ASTM solvent cement, trenching refilling & testing of joints Complete (External work) - 75mm nominal outer dia pipes

Providing and fixing gun metal non return valve of approved quality (screwed end) 25 mm nominal bore - Horizontal.

Providing and fixing CP brass angle valve for basin mixer and geyser points of approved quality conforming to IS 8931 - 15 mm nominal bore.

Providing and fixing in position precast R.C.C manhole cover and frame of required shape and approved quality LD-2.5 Rectangular shape 600x450mm internal dimensions.

Constructing brick masonry chamber for underground C.I. inspection chamber and bends with bricks in cement mortar 1:4 (1 cement : 4 coarse sand) C.I.cover with frame (light duty) 455 x 610 mm internal dimensions , total weight of cover with frame to be not less than 38 kg (weight of cover 23 kg and weight of frame 15kg), R.C.C. top slab with 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) foundation concrete 1:5:10 (1 cement : 5 fine sand : 10graded stone aggregate 40mm nominal size ), inside plastering 12mm thick with cement mortar 1:3 (1 cement : 3 coarse sand) finished smooth with a floating coat of neat cement on walls and bed concrete extra complete as per standard design - inside dimensions 600 x 850 mm and 45 cm deep for pipe line with three or more inlets - with common burnt clay F.P.S. (non modular) bricks of class designation 7.5

Supplying and lowering of UPVC 150mm dia Plain casing pipe confirming to IS. 12818-1992 with relevant amendments with class designation CM and with minimum wall thickness of 7.5 mm as per I.S.Code into the bore well with proper vertical alignments etc. Including the cost of materials , but excluding the cost of labour for positioning the assembly for lowering purpose using contractor's rig

Providing and fixing brass gate valve with C.I. wheel of approved quality (screwed end) - 40mm nominal bore.

Providing and fixing brass gate valve with C.I. wheel of approved quality (screwed end) - 50mm nominal bore.

Providing and fixing ball valve (brass) of approved quality complete - high or low pressure with plastic floats - 25mm nominal bore.

Providing, laying and jointing UPVC pipes (Finolex/ Jain) (1 Mpa) conforming to IS specification 4985 and ISI marked including transportation to the site , lowering to the trenches, laying to proper grade and alignment, testing of joints with required testing equipment,including cost of solvent cement,UPVC specials such as bends, tees, threaded pieces, couplers, reducer, endcaps etc., complete all as per IS and CPWD specification. - 20mm dia.

Providing, laying and jointing UPVC pipes (Finolex /Jain) (1 Mpa) conforming to IS specification 4985 and ISI marked including transportation to the site , lowering to the trenches, laying to proper grade and alignment, testing of joints with required testing equipment,including cost of solvent cement, UPVC specials such as bends, tees, threaded pieces, couplers, reducer, endcaps etc.,complete all as per IS and CPWD specification. - 50 mm dia.

Providing, laying and jointing UPVC pipes(Finolex/ Jain) (1 Mpa) conforming to IS specification 4985 and ISI marked including transportation to the site , lowering to the trenches, laying to proper grade and alignment, testing of joints with required testing equipment,including cost of solvent cement,UPVC specials such as bends, tees, threaded ieces, couplers, reducer, endcaps etc.,complete all as per IS and CPWD specification. - 110 mm dia.

Providing and fixing in position UPVC moulded reducer coupler (Finolex/Jain)(1 Mpa) conforming to IS 7834 part II and ISI marked,including labour charges for jointing, jointing materials etc,complete - 25 x 20mm dia

Providing and fixing in position UPVC moulded elbow (Finolex/Jain)(1 Mpa) conforming to IS 7834 part II and ISI marked,including labour charges for jointing, jointing materials etc,complete - 110mm dia

Supplying and fixing of DOL starters 0.5 HP to 5 HP with relay range 0.63 A to 13 A with suitable M.S. angle frame complete.

Supplying of UPVC plain casing pipe for borewells (FINOLEX / JAIN/Supreme/True bore/ Nandi) conforming to I.S. 12818 -1992 with relevent amendments with class designation 'CM' and with minimum wall thickness 10mm including transportation and stocking at site -200mm dia

Supplying of UPVC ribbed screen slotted pipe for borewells (FINOLEX / JAIN /Supreme/True bore/ Nandi) conforming to IS 12818 -1992 with relevent amendments with class designation 'RS' and with minimum wall thickness 10mm including transportation and stocking at site - 200mm dia

Drilling of borewell anywhere in Pondicherry including tranportation in alluvial soil, sedimentary strata of clay, sand stone, shale, pebbles, boulders etc. by first taking a pilot bore of 140mm / 150mm / 200mm and then enlarging to required dia by direct or reverse rotary mud circulation method,including fuel, labour for drilling, bentonite mud, water required for drilling at the site, contruction of mud pit (water available within a lead of 1.5Km) using rotary rig. -Upto 60 mts depth ending below ground level.

Supplying of electrically operated wet type submersible motor and pumpset (Texmo/ KSB/ Taro/ Kirloskar make), AC 3 phase, 415 volts, 50 Hz, 2900-3000 RPM. The pump shall have brass impeller, high grade steel shaft with sufficient stages with suitable suction and delivery sizes, complete. The rate includes, all taxes, freight, etc., FOR at site in Puducherry. The pumpset shall be guaranteed for a period of one year from the date of commissioning.(5 HP Submersible motor and pumpset open well)

Kota stone slab flooring over 20 mm (average) thick base laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab,including rubbing and polishing complete with base of cement mortar 1:4 ( 1 cement : 4 coarse sand) - 25 mm thick

Providing and fixing stone slab with table rubbed , edges rounded and polished , of size 75x50 cm deep and 1.8cm thick, fixed in urinal partitions by cutting a chase of appropriate width with chase cutter and embedding the stone in the chase with epoxy grout or with cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 6mm nominal size) and finished smooth - White agaria mable stone

Providing and laying soft Korean grass turfing including supplying red earth, manure, river sand, labour charges for ground preparation spreading earth and manure transportation of all and maintaining the lawn for initial three months etc. complete.

Grassing with 'Doob' grass including watering and maintenance of the lawn for 30 days or more tlii the grass forms a thick lawn free from weeds and fit for moving including supplying good earth if needed-in rows 7.5 cm apart in either direction.

Planting of trees by the roadside (Avenue trees) in 0.60 m dia holes, 1 m deep dug in the ground, mixing the soil with decayed farmyard/ sludge manure, planting the saplings, backfilling the trench, watering, fixing the tree guard and maintaining the plants for one year.

40mm thick rubbed stone flooring over 20mm (average) thick base of cement mortar 1:5 (1 cement : 5 coarse sand) with joints 3mm thick, side buttered with cement mortar 1:2 (1 cement : 2 stone dust) admixed with pigment to match the shade of stone and pointing with same mortar. White sand stone.

Demolishing cement concrete manually / by mechanical means including disposal of material within 50 metres lead - 1:4:8 or leaner mix (including equivalent design mix)

Clearing and grubbing road land including uprooting rank vegetation, grass, bushes, shrubs, saplings and trees girth upto 300mm, removal of stumps of trees cut earlier and disposal of unserviceable materials and stacking of serviceable material to be used or auctioned, upto a lead of 1000m including removal and disposal of top organic soil not exceeding 150mm in thickness - by manual means in area of light jungle.

Providing and laying 60mm thick factory made cement concrete interlocking paver block of M-30 grade made by block making machine with strong vibratory compaction and of approved size and design / shape laid in required colour and pattern over and including 50mm thick compacted bed of course sand , filling the joints with coarse sand etc. all complte

Providing and fixing 18mm thick gang saw cut, mirror polished (premoulded and prepolished) machine cut for kitchen platforms,vanity counters,window sills,facias and similar locations , of required size, approved shade,colour and texture laid over 20mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing,curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels - Granite of any colour and shade - Area of slab upto 0.50 sqm

Fabricating supplying and fixing of cast iron solid vertical post of height 1490mm, width 90mm, top width 210mm and 15mm thick designed shape including fixing in position in masonary walls. The cost includes casting molasses free for crack blow holes and all other defects and grinding turning work and making holes to receive barricading pipes etc., to make surface smooth and bring the correct shape as per design and as directed by the Engineer-in-charge. The cost includes applying one coat of approved primer etc. complete.

Supplying and filling with red earth (excluding rock) including cost and conveyance to the work site and stacking to the departmental gauge, spreading in layers not exceeding 20cm in depth, watering and consolidation using 0.5 tonne roller , or wooden or steel rammers etc. complete for making play fields, running tracks and court yards

Supplying and stacking of well decayed cow dung manure at site including carriage complete (Cow dung manure measured in stacks will reduced by 8% for payment)

Removing white or colour wash by scrapping and sand papering and preparing the surface smooth including necessary repairs to scrarches etc.complete

Wall painting with plastic emulsion paint - Royal of approved brand and manufacture to give an even shade - One or more coats on old work

Finishing walls with premium acrylic smooth exterior paint with silicone additives of required shade - New work (two or more coats applied @1.43 ltr / 10 sqm over and including priming coat of exterior primer applied @ 2.20 kg / 10sqm)

Applying priming coats with primer of approved brand and manufacture, having low VOC (Volatile Organic Compound ) content - with water thinnable cement primer on wall surface having VOC content less than 50 grams / litre

Wall painting with plastic emulsion paint - Royal of approved brand and manufacture to give an even shade - two or more coats on new work

painting with black anti-corrosive bitumastic paint of approved brand and manufacture to give an even shade - Two or more coats on new work

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings , with one step CPVC solvement cement and the cost of cutting chases and making good the same including testing of joints complete - Concealed work , including cutting chases and making good the wall etc - 25 mm nominal outer dia pipes

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings. This includes jointing of pipes & fittings with one step CPVC solvent cement, trenching, refilling & testing of joints complete - external work - 50 mm nominal outer dia pipes

Providing and fixing toilet paper holder. Vitreous china.

Providing and fixing in position UPVC fabricated bend (Finolex/Jain)(0.4 Mpa) conforming to IS 7834 part II and ISI marked,including labour charges for jointing, jointing materials etc,complete - 160 mm dia

Making Cornices to an average size of (35cm width and 35cm projection) using brick bats / achukkal with cement mortar 1:2 (1 cement :2 sand)as per detailed drawing (refer details-1) and trowel finish in two layers at an average thickness of 25mm, with C.M. 1:4 (one cement : 4 fine sand)and slightly rounded edges, in decorative elements like moulding, cornice, etc complete. The rates are inclusive of all materials labour scaffolding etc., complete as directed by the Engineer-in-charge.

Steel work welded in built up sections /framed work , including cutting,hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required - in stringers, treads, landings etc. of stair cases, including use of chequered plate wherever required all complete

Providing and fixing aluminimum work for doors, windows, ventilators and partitions with extruded built up standard tubular sections / appropriate Z sections and other sections of approved make conforming to IS : 733 and IS : 1285, fixed with rawl plugs and screws or with fixing clips, or with expansion hold fasteners including necessary filling up of gaps at junctions, at top, bottom and sides with required PVC / neoprene felt etc. Aluminimum sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminimum snap beading for glazing / panelling, C.P. brass / stainless steel screws, all complete as per architectural drawings. (Glazing and panelling to be paid for separately) : For shutters of doors, windows and ventilators including providing and fixing hinges / pivots and making provision for fixing of fittings wherever required including the cost of PVC / neoprene gasket required (fittings shall be paid for separately) polyster powder coated aluminium (minimum thickness of polyster powder coating 50 micron)

Providing and fixing glazing in aluminimum door, window, ventilator shutters and partitions etc., with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings ( cost of aluminium snap beading shall be paid in basic item) - with float glass panes of 8 mm thickness

Providing and fixing M.S.grills of required pattern in frames of windows etc with M.S. flats , square or round bars etc. including priming coat with approved steel primer all complete - Fixed to steel windows by welding

Forming groove of uniform size from 12x12 mm and upto 25x15mm in the top layer of washed stone grit plastered surface as per approved pattern , including providing and fixing aluminium channels of appropriate size and thickness (not less than 2mm) , nailed to the under layer with rust proof screws and nails and finishing the groove complete as per specifications.

Dismantling wood work in frames, trusses, purlins and rafters upto 10 metre span and 5 metre height including stacking the material within 50m lead - Of sectional area 40 square centimetres and above.

Providing and fixing aluminimum work for doors, windows, ventilators and partitions with extruded built up standard tubular sections / appropriate Z sections and other sections of approved make conforming to IS : 733 and IS : 1285, fixed with rawl plugs and screws or with fixing clips, or with expansion hold fasteners including necessary filling up of gaps at junctions, at top, bottom and sides with required PVC / neoprene felt etc. Aluminimum sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminimum snap beading for glazing / panelling, C.P. brass / stainless steel screws, all complete as per architectural drawings. (Glazing and panelling to be paid for separately) : For fixed portion. Powder coated aluminium (minimum thickness of powder coating 50 micron)

Providing and fixing bright finished brass butt hinges with necessary screws etc.complete: - 75x65x4mm (heavy type)

Providing and fixing bright finished brass door latch with necessary screws etc.complete - 300x16x5mm

Providing and fixing bright finished brass handles with screws etc.complete : 75mm

Providing and fixing white vitreous china flat back or wall corner type lipped front urinal basin of 430x 260x350 mm and 340x410x265mm sizes respectively with automatic flusing cistern with standard flush pipe and C.P. brass spreaders with brass unions and G.I.clamps complete, including painting of fittings and brackets, cutting and making good the walls and floors wherever required - Range of two urinal basins with 5 litre white P.V.C. automatic flusing cistern

Providing and laying autoclaved aerated cement blocks masonry with 150mm/230mm/300mm thick AAC blocks in super structure above plinth level up to floor V level with RCC band at sill level and lintel level with approved block laying polymer modified adhesive mortar all complete .(The payment of RCC band and reinforcement shall be made for seperately).

Providing and fixing factory made uPVC white colour casement /casement cum fixed glazed windows comprising of uPVC multi-chambered frame , sash and mullion (where ever required) extruded profiles duly reinforced with 1.60 + or - 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), uPVC extruded glazing beads of appropriate dimension , EPDM gasket , stainless steel (SS 304 grade) friction hinges , zinc alloy (white powder oated) casement handles, G.I fasteners 100 x8 mm size for fixing frame to finished wall , plastic packers , plastic caps and necessary stainless steel screws etc. Profile of frame & sash shall be mitred cut and fusion welded at all corners, mullion (if required) shall be also fusion welded including drilling of holes for fixing hardware's and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealent over backer rod of required size and of approved quality , all complete as per approved drawing.(Single / double glass panes and silicon sealent shall be paid separately) - Casement window single panel with S.S.friction hinges (300x19x1.9mm) , made of (small series) frame 47 x 50 mm & sash 47 x 68 mm both having wall thickness of 1.9 + or - 0.2mm and single glass pane glazing bead of appropriate dimension (Area of window upto 0.75sqm) - (casement windowsize 0.50 x 1.35 m)

Providing & fixing precoated galvanised iron profile sheets (size, shape, and pitch of corrugation as 0.50mm (+0.05%), total coated thickness with zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer onboth sides of the sheet and polyster top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length upto 12 metre or as desired. The sheet shall be fixed using self drilling / self tapping screws of size (5.5 x 55 mm) with EPDM seal, complete upto any pitch in horizontal / vertical or curved surfaces, excluding the cost of purlins , rafters and trusses and including cutting to size and shape wherever required