PROVISION OF ADDITIONAL TOILETS BATHROOMS NEAR P 464 FOR L IN AIR WARRIORS OF 37 WG AT AF STN CARNICOBAR AND PROVN OF FLAME PROOF LIGHTS AND WIRING AT 955 SQN POL STORE AT AF STN CARNICOBAR.

Amount

Surface dressing not exceeding 15 cm deep in soft/loose soil all as specified and as directed.

Excavation in trenches n.exc 1.5 M wide and n. exc 1.5 M depth and getting out in soft/loose soil getting out complete all as specified and as directed.

Returning filling in, including spreading, levelling, watering and well ramming in layers not exc 25 cm in soft/loose soil complete all as specified and as directed.

Removing excavated material (soil) n.exc 50 m and depositing where as directed at a level n.exc 1.5 m above the starting point complete all as specified and as directed.

Material and labour for plain cement concrete 1:4:8 type D2 using 40 mm graded stone aggregate as in foundation filling and mass concrete including necessary form work complete all as specified and as directed.

M&L for Pre-cast cement concrete block masonry with solid blocks using type C1(1:3:6) (20mm graded aggregate) ,size exc 10cm in width and setting in cement mortar 1:6 complete all as specified and directed.

Material and labour for precast PCC 1:3:6 Type C1 using 20 mm graded aggregate solid block masonry not exceeding 10 Cm width(with plain or interlocking joints as directed), built in cement mortar 1:6 all as specified and as directed.

Material and labour for reinforced cement concrete 1:2:4, type B1,using 20 mm graded granite stone aggregate in foundaions including rafts, footings, foundaion beams, plinth beams, bases for columns etc, basement slabs, underreamed piles and mass concrete all as specified and as directed. Note : Reinforcement and form work shall be measured and paid separately.

S&F prepainted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50 mm thick of an colour having tensile strength 550 MPA as in roof covering in roof covering /cladding to wall, fixed with self tapping screws including providing of rubber washer/Bitumen washer with filling of Bitumen between joint of sheet and Self tapping screws complete all as specified.

S&F prepainted galvalume aluminium zinc coating GI based plain steel sheet 0.50 mm thick of an colour having tensile strength 550 MPA as in roof covering in roof covering /cladding to wall, fixed with self tapping screws including providing of rubber washer/Bitumen washer with filling of Bitumen between joint of sheet and Self tapping screws complete all as specified.

Supply and fix rolled mild steel in roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats conforming to Fe-410W(Gde E-250) quality A complete all as specified and as directed.

Supply and Fixing Mild steel work such as joist, channel, angle or tee section fixing independently without connecting plates, cut to ordinary length ie, within 20mm of the length indicated conforming to Grade E-250, Fe 410 W quality B all as specified and as directed.

Material and labour for providing reinforced cement concrete 1:2:4 type B1 nominal mix using 20mm graded stone aggregate as in chajjas supported on walls, beams and columns using all as specified and directed.

Material and Labour for TMT bar 10mm dia and over, cut to length, bent to shape required, including cranking,bending spirally for hooping ,for columns,hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia confirming to Fe-410-S or Fe-410-0 or securing with clips complete all as specified and as directed.

M&L mild steel TMT bars 5mm dia and over up to 10mm for stirrups cut to length , bent to shape required including cranking, bending, spirally hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia bars confirming to Fe-410-S or Fe-410-0 complete in all respect as specified and directed.

Use and waste of formwork to sides and soffits of chullah hoods, chajja, troughs and similar works finished fair surfaces, flat complete all as specified and as directed.

Use and waste of form work to edges of concrete flats, threads, breaks in floors, window cills, concrete railings, openings in concrete walls, floor and roofs not exceeding 20 cm wide and sides of RCC/PCC bands in walls, horizontal or sloping and similar work exceeding 10 cm but not exceeding 20 cm wide for fair finished surfaces.

Material and labour for 40 mm thick damp proof course in cement concrete 1:2:4 type B0 to horizontal or vertical surfaces including necessary form work complete all as specified and as directed.

Material and labour for Moorum filling in floors/pavings obtained from outside MD land, laid in layers not exceeding 15 cm thick, spread, levelled and rammed/rolled including watering to required level and gradient all as specified and as directed.

Material and Labour for anti termite treatment with Treating the backfill in contact with foundation at the rate of 7.5 litres per sq.m of the vertical surface of the sub-structure to a depth of 300mm (Area of the sub structure in contact with backfill to be measured) complete all as specified and as directed.

Material and Labour for plain cement concrete 1:2:4 type B1 using 20mm graded granite stone aggrgate as in in lintels upto 1.5m clear span, cills, steps; seismic and other similar bands, plinth courses, string courses, lacing courses, parapets and railings upto 60 cm in height, copings, kneelers, apex stones, bed plates and the like including weathering, slightly rounded or chamfered angles and throating including use of necessary form work all as specified and as directed.

Material and Labour for rendering 5 mm thick in cement mortar 1: 4 on fair faces of concrete surfaces of ceiling finished even and smooth with out using extra cement, complete all as specified.

Material and labour for 15 mm thick rendering on brick/concrete surfaces in two layers in CM 1:4, finishing coat of 5mm thick, finished even and smooth without using extra cement complete all as specified and as directed.

Material and labour for rendering 15 mm on fair faces of brick or concrete surfaces in CM 1:6, finished even and fair without using extra cement complete all as specified and directed.

Material and labour for preparation of of new plastered/concrete surfaces of walls and applying two coats of acrylic distemper of approved shade/tint over a coat of primer, over 3mm thick wall care putty finish to achieve uniform smooth surface of wall all as specified and as directed.

Material and labour for applying Two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over new surfaces complete all as specified and directed.

Supply and fixing 6 mm thick bevelled edge looking mirror of size 600 x 450 mm mounted on 6 mm thick AC Building board or commercial plywood/hard board backing and fixed to wooden plugs with CP Screws and cup washers all as specified and as directed.

Supply and fixing in repairs vitreous China wash hand basin, white (flat back or angle back type or counter top) of size 550X400mm including 32mm brass chromium plated waste fitting, a pair of cast iron bracket duly painted including cutting and pinning in ends making good disturbed surfaces in CM 1:3 excluding pillar tap but chain , plug and porcelain stopper, brackets etc all as specified and as directed.

Supply and fix stop valves/angle cock, 15mm bore, fancy type, chromium plated, screwed down, high pressure with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed complete all as specified and directed.

Supply and fixing in repairs Vitrious China squatting pan ' Orissa' pattern of size 580 mm x 440 mm white with integral foot rest excluding flushing cistern and flush pipe including P or S trap making good the floor to match with existing floor complete all as specified and as directed.

Supply and fixing Vitreous China full stall urinal bowl type (back or corner wall type), white , of size 580mm x 380mm x 350mm complete with chromium plated waste fittings including providing and fixing plugs,bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including 60mm long brass screws, pointing arround urinal back in cement, (minimum), with grating and union for discharge pipe (excluding flushing cistern, flush pipe and waste pipe) all as specified and as directed.

Supply and fix Rotational moulded Polyetheylene Water Storage Tank 1000 Ltr capacity Triple Layer (Cylinderical verticle with closed top) including 20mm dia GI Medium Grade 450mm long overflow and wash out pipe each with all required fittings, Checknut, Stopper etc complete hoisted and fixed in position, including all incoming and outgoing connection of GI pipe complete and including 25mm PTMT Ball valves high pressure wiith epoxy coated aluminium rod and high density plastic ball screwed for iron pipe complete for 20mm dia pipe fixed on roof top complete all as specified and directed.

Supply and fixing galvanised steel water tubing medium grade 15 mm bore including all necessary fittings such as bends, L bows, short piece connections, backnuts, caps plugs, unions couplings, flanges, sockets etc, fixed to wall/floor/ceiling including necessary cutting/chauging in walls made of brick/concrete surface complete all as specified and as directed.

Supply and fixing galvanised steel water tubing medium grade 20 mm bore including all necessary fittings such as bends, L bows, short piece connections, backnuts, caps plugs, unions couplings, flanges, sockets etc, fixed to wall/floor/ceiling including necessary cutting/chauging in walls made of brick/concrete surface complete all as specified and as directed.

Supply and fix Bib taps, 15mm bore, cast copper alloy, chromium plated with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule and fixed, complete all as specified and directed.

Supply and fix aluminium powder coated frame for doors,windows, ventilators with one or more rebates with joint clip and using rubber beading etc complete all as specified and directed. Note : Glass panel/particle board panel filling shall be measured and paid separately.

Supply and fix for powder coated, Anodised aluminium window and ventilator shutters, side hung type without sash bars, aluminium sections weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws, anodised aluminium fittings such as peg stays 150mm long (1 no.), hinges type B-21 100mm long (2 no.) suitable handle (1 no.) complete all as specified.

Supply and fix Aluminium alloy wire cloth 0.45mm nominal dia of wire and average width of aperture 1.40mm and fixed with Aluminium alloy wire staples complete all as specified and directed

Supply and Fixing Figured/frosted glass 5.5mm thick, pin head type and glazing with oil and putty in square not exc 0.5 sqm in each pane complete all as specified and as directed.

Supply and fixing Solid PVC Door Frame of size 50 mm x47mm made out of 5 mm plain colour PVC sheet reinforced with M.S. Square tube, supporting & fixing in opening as per specification & drawing complete all as specified and directed.

Supply and fix factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of mild steel tubes for top & bottom rails, mild steel frame shall be covered with heat moulded plian colour PVC 'C' channel having a PVC sheet strip of 20 mm width struck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail, panelling of plain colour PVC sheet to be fitted in the mild steel frame welded/sealed to the stiles & rails with suitable PVC sheet beading, and jointed together with solvent cement supplying and fixing in the frame at site as per specification & drawing of SSR Part II.

Supply and fix extruded aluminium alloy handles, fabricated type, anodised 150mm size complete all as specified and as directed

Supply and Fix 125mm long aluminium anodised barrel tower bolt of extruded section all as specified and as directed by Eng-in-charge.

Supply and fixing aluminium alloy,anodised, sliding door bolt of length 250mm with hasp, staple (bolt type) & fixing clips of sheet, cast or extruded sections & fixing bolts & sliding bolts of extruded section or cast-aluminium alloy complete all specified and as directed.

Supply and fix 100mm long mild steel cold rolled medium weight butt hinges fixed with screws to wooden frames or with welding to steel frames including all accessoriescomplete all as specified and as directed.

Supply and fix in repair 10 Ltr capacity PVC valveless, syphonic action type, flushing cistern low level, white, with inlet ball valve, float and handle including brackets, flushing pipe, 450mm long PVC Connection and connection to trap, and to flushing and making good to floor complete all as specified .

Supply and fixing in repairs flush pipe of polyethylene of low or high density or PVC 32 mm dia, for low level cistern complete all as specified and directed.

Supply and fix in repairs PVC connections 15mm size with PTMT nuts of length 600mm complete all as specified and directed.

Supply and fix 15mm dia pillar tap, cast copper alloy, chromium plated, fancy type, with capstan head screwed down high pressure with or without lettered hot or cold with long screw shank and fly nutt screw for iron pipe Make: CERA /Parryware/Hindware

Supply and fixing in repairs Towel rails tubular brass chromium plated 20 mm dia 'D' type 60 cm long between flanges complete all as specified and directed.

Supply and fixing in repairs PVC waste pipe 32mm dia with 40mm dia reducer, 90cm long for WHB/urinal outlet with 4 Nos screws for fixing pipes, complete all as specified and directed.

Supply and fix Sheet glass shelf assembly consisting of 5.5mm thick sheet glass shelf 12cm wide with chromium plated bracket guard and railing 60cm long, complete all as specified and as directed.

Supply and fix in repairs waste coupling of PTMT 32 mm size (half or full threaded) suitable for urinals/ WHB/Sink etc (Minimum weight 32 mm - 45 gms) all as specified and as directed.

Taking down unservicable shower rose and supply and fix brass chromium plated shower rose 125mm size with swivel joints including fixing to steel pipe or union complete all as specified and as directed.

Supply and fix soap dish vitireous china white 160x160x90mm (Approximate) complete all as specified and as directed.

Supply and fixing urinal partition , vitreous china, white, of size 310mmx770mmx50mm all as specified and as directed.

Material and Labour for non-skid coloured ceramic tiles 7 to 8mm thick (square/ rectangular) area of each tiles exceeding 0.11 Sqm but not exceeding 0.18 Sqm in floors etc, set and jointed in cement mortar and pointed in white of coloured cement to match over and including 15mm thick screed bed in CM 1:6 complete all as specified and as directed. NOTE: No extra cost shall be allowed for removing and re-fixing and necessary cutting of door etc if any required during execution of work.

Material and Labour for glazed ceramic coloured tiles in vertical surface 450x300x7-8mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match the tiles over and including 10mm thick backing coat in CM 1:4 cmplete all as specified.

Supply and fix stainless stell coat hook set of five with suitable SS base plate complete all as specified and as directed.

Material and labour for 100mm thick plain cement concrete 1:4:8 type D-2 using 40 mm graded stone aggregate as in sub base of floors including necessary form work all as specified and as directed.

Material and Labour for 40mm thick plain cement concrete 1:2:4 type B1 using 20mm graded stone aggrgate as floor and other similar type of work, and finishing cement concrete surface even and smooth Without using extra cement, complete all as specified and as directed.

Supply and fix anodised aluminium snap grid frame work for false ceiling with 605mm x 605mm size, consisting of main Tee of size 40 x 40 x 2mm, cross Tee of size 40 x 40 x 2mm and wall angle of size 40 x 40 x 2mm of approved make including all necessary cuttings, fixing of aluminium section firmly in position with and including steel hangers 6 mm dia G.I. wire (upto 1200 mm length) adjusting level fixed to roof slabs by means of ceiling cleats made out of G.I. flat 40 x 3 mm size 60 mm long and expansion hold fasteners 40 mm long in soffit of slab/walls complete all as specifed and as directed including provision of with 4mm thick Non Asbestos boards, ordinary type for fixing in 600 mm x 600mm grid, fixed in ceiling, flat or sloping, complete all as specified and directed. Note :- Rate quoted above shall be deemed to include for making holes, cutting chassis if any required and making good to existing walls in cement mortar 1: 3 to match with existing surface finish as directed at site.

Material and labour for hard core with broken stone or boulders of gauge not exceeding 63 mm, deposited, spread, and levelled in layers not exceeding 15 cm thick watered and rammed to a true surface all as specified and as directed.

Material and Labour for 75mm thick Plain Cement Concrete 1:3:6 type C2 using 40 mm graded stone aggregate as in plinth protection, floors, pavings and hardstanding etc, finished even smooth without using extra cement etc including necessary forwork, complete all as specified and as directed.

S&F PVC (SWR) 75 mm bore vent cowl complete all as specified and as directed.

S&F in repair PVC (SWR) pipes 110 mm dia. single socketed, in any length with rubber ring joints, fixed to wall and roof as in rain water gutters including cutting of PVC pipes in half complete all as specified and as directed.

S&F PVC (SWR) pipes 75 mm dia. single socketed, in any length with rubber ring joints, fixed to wall complete all as specified and as directed.

S&F PVC (SWR) bend 75 mm dia with access door complete all as specified and as directed.

Supply and fix PVC (SWR) floor trap , plain with grating including jointing with solvent cement 75mm bore complete all as specified and as directed.

S&F PVC (SWR) junction single 110 mm bore, (single T) equal or unequal with access door complete all as specified and as directed.

Surface excavation not exceeding 30cm deep and averaging 15cm deep and getting out in soft/loose soil complete all as specified and as directed.

Material and labour for machine pressed precast concrete interlocking paver block, any shape and size of 60mm thickness M-35 grade conforming to IS 15658-2006 with grey cement and pigment laid over and including 30mm thick river sand cushioning, compacted with mechanical surface vibrator and with scratch proof lacquer coating on top surfaces complete all as specified and directed.

Material and labour for providing cement concrete 1:2:4 type B1 using 20 mm graded stone aggregate cast in situ as in kerbs or mud stops, rounded or chamfered on edges, as directed including use of form work as necessary all as specified and as directed.

Excavation over areas n. exc 1.5 m deep and getting out in soft/loose soil complete all as specified and as directed.

Excavation over areas exc 1.5 m depth and n. exc 3.0 m deep and getting out in soft/loose soil complete all as specified and as directed.

Material and Labour for PCC 1:3:6, type C-2 as in concrete bed to drain pipes including packing under and completely surrounding pipes after they are laid and tested for 150mm dia pipe and testedcomplete all as specified and as directed.

Supply and laying Reinforced cement concrete hume pipes class NP2, laid and jointed complete with one collar per length of pipe, dia 150 mm complete all as specified and as directed.

Material and Labour for plain cement concrete 1:2:4 type B1 using 20mm graded granite stone aggrgate as in in lintels upto 1.5m clear span, cills, steps; seismic and other similar bands, plinth courses, string courses, lacing courses, parapets and railings upto 60 cm in height, copings, kneelers, apex stones, bed plates and the like including weathering, slightly rounded or chamfered angles and throating including use of necessary form work all as specified and as directed.

M&L for Pre-cast cement concrete block masonry with solid blocks using type C1(1:3:6) (20mm graded aggregate) ,size exc 10cm in width and setting in cement mortar 1:4 complete all as specified and directed.

Material and labour for 15 mm thick rendering on brick/concrete surfaces in two layers in CM 1:4, finishing coat of 5mm thick using water proofing compound @3% by weight of cement, finished even and smooth without using extra cement complete all as specified and as directed. Note: Water proofing compound shall be measured separately.

Supply only integral water proofing compound all as specified and as directed.

Material and labour for Precast reinforced cement concrete 1:2:4 type B1 using 20mm graded stone aggregate as in cover slabs of man holes including necessary form work, placed in position, set in CM 1:4 complete all specified and as directed.

Material and labour for Loose filling with broken stone aggregates of gauge 40 to 80 mm in soakage pits, soakage wells, etc complete all as specified and as directed.

Material and labour for reinforced cement concrete 1:2:4, type B1,using 20 mm graded granite stone aggregate as in Slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like complete all as specified and as directed. Note : Reinforcement and form work shall be measured and paid separately.

Use and waste of formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings, and similar work, not exceeding 200 mm thick etc, fair finshed surfaces of concrete (Horizontal or sloping) complete all as specified and as directed.

Supply and fix galvanised steel water tubes, medium grade, 32mm bore with and including all GI fittings such as bends, L bows, short piece connections, backnuts, caps plugs, unions couplings, flanges, sockets etc., laid in trenches/floor including inter connection between buildings/pumps/pump houses , complete all as specified and as directed.

Supply, fixing, laying & testing galvanised iron water tubing of 25 mm dia, medium grade, ISI marked with and including all GI fittings such as unions, reducer sockets, socket reducing bends, elbows, tee, checknuts, caps, plugs etc.fix on wall/floors/roofs/ceiling etc., complete all as specified and directed

Supply and fix Gun metal, globe or gate valves 25mm, with iron wheel head, screwed both ends for iron pipe and fixed complete all as specified and as directed.

Supply and fix Float valve high pressure of PTMT with epoxy coated Aluminium rod & high density plastic ball screwed for iron pipe suitable for 25mm bore complete all as specified and as directed.

M & L for point wiring using 1.5 Sqmm lSI marked 1.1 KV grade single core FR LS flexible cable, conforming to IS: 694-1990, having multi-drawn thin strands of electrolytic copper conductors, conforming to IS: 8130-1984 and insulation conforming to IS: 5831-1984, for phase, neutral and earth continuity conductor connecting to earth dolly, drawn in and including not less than 20 mm PVC medium conduits/ casing capping, conforming to IS: 9537 (Part 3)- 1983, colour coded as specified in IS: 11353-1985, including factory made sunken, galvanized, not less than 1.00 mm thick modular flush sheet metal enclosure having top, bottom, side and back-wall knockout for conduit entry from any direction, conforming to IS: 14772- 2000 and suitable for modular cover-plates complete all as specified in IS: 732-1989 and directed for the following:-.

(a ) one light point or one fan point controlled by one switch 5 Amps

(b) One 3 pin socket outlet 5 Amps on same board

(c) one 3 pin socket outlet 5 Amps point controlled by one switch on Independent board.

M & L for point wiring using 2.5 Sqmm lSI marked 1.1 KV grade single core FR LS flexible cable, conforming to IS: 694-1990, having multi-drawn thin strands of electrolytic copper conductors, conforming to IS: 8130-1984 and insulation conforming to IS: 5831-1984, for phase, neutral and earth continuity conductor connecting to earth dolly, drawn in and including not less than 20 mm NB PVC medium grade conduits (concealed), conforming to IS: 9537 (Part 3)- 1983, colour coded as specified in IS: 11353-1985, including factory made sunken, galvanized, not less than 1.00 mm thick modular flush sheet metal enclosure having top, bottom, side and back-wall knockout for conduit entry from any direction, conforming to IS: 14772- 2000 and suitable for modular cover-plates complete all as specified in IS: 732-1989 and directed for 6 pin switch socket outlet 5 Amp on independent board complete all as specified and directed by Engineer in charge:-. Note: Circuit wire from DB to switch boards shall be included in the quoted rate. No additional payment will be paid to the contractor for the circuit submain.

Supply and fix Switch piano flush type 5 amps single pole, one way, 240 Volts complete all as specified and as directed.

Supply and Fix Ssocket outlet 5 pin, 6 Amps and AC 230 volts flush type complete all as specified and as directed.

Supply & fix switch socket combination outlet, 6 pin, 6 Amps, multipurpose, flush, non shutter, non inter locking type, 230 volt flush type, white/ivory finish with fixing hole complete all as specified and directed by Engineer in charge.

Supply & fix switch socket combination, 6 pin, 15/16Amps, multipurpose , flush, shutter type, 230 volt flush type, white/ivory finish with fixing hole complete all as specified and directed by Engineer in charge.

Supply and fix Ceiling rose in poly carbonate 3 plates flush type 6 Amps, 250 volts AC complete all as specified and directed.

S&F LED Panel Square, slim compact, aluminum die cast edge LED recess mounted square downlight fixture panel fitting 18 watt, 220 V AC recessed type with high efficiency PMMA diffuser soft glare free even light distribution with driver suitable for roof ceiling, connecting up with Driver three core flexible copper conductor cable and fixture, complete all as specified and directed by Engr-in-Charge. Make- Philips/Bajaj/Crompton /Havells.

Supply and fixing LED mirror light fittingwith high out put diffuser 12 watt 220 V AC decorative type with driver holder and LED lamp including connecting up with three core flexible copper conductor cable of suitable size complete. Make- Philips/Bajaj/Crompton /Havells.

Supply and fixing LED light fitting 35 watt street light for building security lights, 230 Volts, outdoor type & Wide temperature operating range: -10 °C to +50 °C, with best in class design & roubst heat sink for better heat dissipation, electronic driver unit with IP 65/66 protection,lamp bracket with impact and corrosion resistant including two coat of silver coloured Mild steel angled pipe of suitable size for fixing of security light, necessary mounting bolts, nuts and washers, fixing on iron angle complete all as specified and directed by Engr-in-charge. Make: Crompton/Philips/Bajaj/Havells.

Supply and fix Exhaust Fan of size 300 mm sweep with louvers, with metal body AC 230 V, 50 Hz, 1200 RPM and connecting to ceiling rose terminals with 23/.0076 flexible cable, complete all specified and directed. Make:Havells/ Usha/Crompton Greaves.

Material and labour for Sub main wiring using two runs of single core PVC insulated cable (FR) 4 sqmm copper conductor multi stranded and one run of 4 sqmm copper conductor insulated cable (FR)using as earth wire drawn through and including suitable size rigid non-metallic PVC conduit, complete all as specified and directed. Note- 3 run of 4 sq mm PVC copper wire and One run of PVC conduit shall be measured and paid as one unit.

Supply and fix Distribution board (DB) made out of sheet metal enclosure (CRCA sheet), dust and vermin proof, SPN 8 way with 200 Amps rated copper bus bar single door protection, neutral bar,earth bar, single pole and neutral 240 volts, MCBs used as incommer flush to wall complete all as specified and as directed.

Supply and fix MCB SP 6-32 amp rating 240V, 10KA 'B' curve miniature circuit breaker (MCB) of single pole in the MCB DB,IP 20 transparent lebel holder fully insulated safety shutters suitable for cable up to 35 Sqmm cross sectional area complete including suitable size copper Lugs complete all as specified and directed. Make: Indo Asian/ L&T/Crompton Greaves/Havells

Supply and fix MCB SPN 40 to 63 amp rating 240V, 10KA 'C' curve miniature circuit breaker (MCB) of single pole in the MCB DB complete with connection testing and commissioning complete all as specified and directed. Make: Indo Asian/ L&T/Crompton Greaves/Havells

Supply, laying or passing through pipe LT, XLPE insulated, galvanised steel strip or wire armoured electric power cable (heavy duty) with stranded aluminium conductor 1100 Volts grade of size 10 Sqmm 2 core including testing and necessary fixing arrangements such as lugs, glands and terminal of suitable size for connection of cable ends, complete all as specified and directed.

Supply and laying double wall corrugated pipe (DWC) conforming to IS 19430 Part -1 of size 63mm outer dia and 50 mm inner dia etc for cable protection, complete all as specified and as directed.

Earthing complete with galvanised steel earth plate electrode 60 cm x60 cm x 6 mm thick buried directly in ground ,(Earth pit not less than 2.25 meter deep below ground level) with top edge of plate not less than 1.5 meter below normal ground level ,connected to and including galvanised iron earth wire 4.0mm dia by means of nut, bolts, check nuts and washers of galvanised iron or steel and provision of charcoal dust and common salt packed all around the earth plate including necessary excavation and earth work in any type of soil and testing complete all as specified and directed and shown in electrical plate number 3 of MES SSR part-I(2009) Note: Unit rate quoted shall be deemed to be included the following (a) Excavation and earth work for drilling hole for electrode in any type of Soil. (b) PCC pit in cement concrete 1:2:4 type B-1, Pre cast RCC cover with suitable handle 40 mm thick in PCC 1:2:4 type B-1, reinforced with welded steel wire fabric weighing not less than1.87 Kg/ Sq meter. (c) Funnel with watering pipe of GI 25 mm nominal bore light grade and lugs etc complete all as specified and directed (d) 25 mm nominal bore medium grade GI protection pipe 7.5 meter long for protection of earthing lead complete all as specified and directed. (e) Requisite quantity of common salt and charcoal. (f) Testing of earthing.

Supply and Fix High density polyethylene pipes (HDPE) of pressure rating 6 kgf/cm2 laid in trenches 50 mm bore with all acessoires for cable protection, complete all as specified and as directed.

M & L for point wiring using 1.5 Sqmm lSI marked 1.1 KV grade single core FR LS flexible cable, conforming to IS: 694-1990, having multi-drawn thin strands of electrolytic copper conductors, conforming to IS: 8130-1984 and insulation conforming to IS: 5831-1984, for phase, neutral and earth continuity conductor connecting to earth dolly, drawn in and including not less than 20 mm NB PVC medium grade conduits (concealed), conforming to IS: 9537 (Part 3)- 1983, colour coded as specified in IS: 11353-1985, including factory made sunken, galvanized, not less than 1.00 mm thick modular flush sheet metal enclosure having top, bottom, side and back-wall knockout for conduit entry from any direction, conforming to IS: 14772- 2000 and suitable for modular cover-plates complete all as specified in IS: 732-1989 and directed for the following:-. Note: Circuit wire from DB to switch boards shall be included in the quoted rate. No additional payment will be paid to the contractor for the circuit submain. (a ) one light/fan point controlled by one switch 5 Amps

Supply and fix Switch flame proof, rotary type with termination box in LM6,16 A, single pole, 250 V complete all specified and as directed.

Supply and Fixing of Flameproof cum Waterproof LED light fitting of 2x16W, CMRI certified recommended for gas/vapor group of IIA & IIIB, Zone 1 & 2 and IP65 protection of Cast Aluminum alloy material and Heat and Impact resistance toughen 'A' clear glass having Anti corrosive epoxy powder coated finish complete with all accessories pre wired and including connecting up with three core flexible copper conductor cable with suitable size.complete all as specified and as directed. Make:Bajaj/ L&T/Crompton Greaves/Havells

Supply and fix Flame proof exhaust fan of size 380 mm sweep with louvers,having air discharge capacity of 1120CFM with metal body AC 230 V, 50 Hz, 1440 RPM and connecting to ceiling rose terminals with 23/.0076 flexible cable complete all specified and directed. Make:Havells/ Usha/Crompton Greaves.

Supply and fix Flame proof Distribution board (DB) made out of sheet metal enclosure (CRCA sheet), dust and vermin proof, SPN 6 way with 5000 Amps rated copper bus bar double door protection, neutral bar,earth bar, single pole and neutral 240 volts, MCBs used as incommer flush to wall complete all as specified and as directed, with the following electrical items including all connection- Incoming :- MCB, Double Pole, 32 Amp- 01 Nos Outgoing :- MCB, Single Pole, 6/10 Amp- 04 Nos

Cutting openings, through brick walls for door, window and other openings or enlarging existing openings, converting window into door openings, etc. or cutting out defective brick work for under-pinning, including providing, fixing and removing shoring, cleaning and stacking bricks, removing surplus serviceable bricks, hard-core, etc., to store and rubbish not exceeding 50 M all directed.

ASHOK BISWAS (BID ID -3464391)

City Constructie Pvt Ltd (BID ID -3463578)

BHARAT MULTITECH INDUSTRIES PVT LTD (BID ID -3464088)