Construction of New ATC Tower and Technical Block at Varanasi Airport

Amount

Earth work in excavation by mechanical means (Hydraulic excavator)/manual means over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan) including getting out and disposal of excavated earth lead upto 50 m and lift upto 1.5 m, as directed by Engineer-in-charge. All kinds of soil

Earth work in excavation by mechanical means (Hydraulic excavator) / manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, lift upto 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m. All kinds of soil

Supplying and filling in plinth with sand under floors, including watering, ramming, consolidating and dressing complete.

Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift upto 1.5 m.

Extra for every additional lift of 1.5 m or part thereof in excavation / banking excavated or stacked materials. All kinds of soil

Excavating trenches of required width for pipes, cables, etc including excavation for sockets, and dressing of sides, ramming of bottoms, depth upto 1.5 m, including getting out the excavated soil, and then returning the soil as required, in layers not exceeding 20 cm in depth, including consolidating each deposited layer by ramming, watering, etc. and disposing of surplus excavated soil as directed, within a lead of 50 m : All kinds of soil

Pipes, cables etc, not exceeding 80 mm dia.

Pipes, cables etc. exceeding 80 mm dia. but not exceeding 300 mm dia

Extra for excavating trenches for pipes, cables, etc. in ordinary/hard rock exceeding 1.5 m in depth but not exceeding 3 m. (Rate is over corresponding basic item for depth upto 1.5 metre) Pipes, cables etc. exceeding 80 mm dia. but not exceeding 300 mm dia.

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level :

1:2:4 (1 cement : 2 coarse sand (zone-III) : 4 graded stone aggregate 20 mm nominal size).

1:3:6 (1 Cement : 3 coarse sand (zone-III) : 6 graded stone aggregate 20 mm nominal size).

1:4:8 (1 Cement : 4 coarse sand (zone-III) : 8 graded stone aggregate 40 mm nominal size)

1:5:10 (1 cement : 5 coarse sand (zone-III): 10 graded stone aggregate 40 mm nominal size).

Providing and laying cement concrete in retaining walls, return walls, walls (any thickness) including attached pilasters, columns, piers, abutments, pillars, posts, struts, buttresses, string or lacing courses, parapets, coping, bed blocks, anchor blocks, plain window sills, fillets, sunken floor etc., up to floor five level, excluding the cost of centering, shuttering and finishing : 1:2:4 (1 Cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size).

Providing and fixing at or near ground level precast cement concrete in kerbs, edgings etc. as per approved pattern and setting in position with cement mortar 1:3 (1 Cement : 3 coarse sand), including the cost of required centering, shuttering complete. 1:1½:3 (1 Cement: 1½ coarse sand(zone-III) : 3 graded stone aggregate 20 mm nominal size).

Making plinth protection 50mm thick of cement concrete 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) over 75mm thick bed of dry brick ballast 40 mm nominal size, well rammed and consolidated and grouted with fine sand, including necessary excavation, levelling & dressing & finishing the top smooth.

Providing and laying damp-proof course 50mm thick with cement concrete 1:2:4 (1 cement : 2 coarse sand(zone-III) : 4 graded stone aggregate 20mm nominal size).

Extra for providing and mixing water proofing material in cement concrete work in doses by weight of cement as per manufacturer's specification.

Providing & applying a coat of residual petroleum bitumen of grade of VG-10 of approved quality using 1.7kg per square metre on damp proof course after cleaning the surface with brushes and finally with a piece of cloth lightly soaked in kerosene oil.

Extra for concrete work in superstructure above floor V level for each four floors or part thereof.

Providing and laying in position machine batched and machine mixed design mix M-25 grade cement concrete for reinforced cement concrete work, using cement content as per approved design mix, including pumping of concrete to site of laying but excluding the cost of centering, shuttering, finishing and reinforcement, including admixtures in recommended proportions as per IS: 9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability as per direction of Engineer-in-charge.“(Note :- Cement content considered in this item is @ 330 kg/cum.“Excess/ less cement used as per design mix is payable/ recoverable separately).

All works upto plinth level

All works above plinth level upto floor V level

Extra for providing richer mixes at all floor levels. Note:- Excess/less cement over the specified cement content used is payable /recoverable separately. Providing M-30 grade concrete instead of M-25 grade BMC/ RMC. (Note:- Cement content considered in M-30 is @ 340 kg/ cum) Note:- For the purpose of tendering, the quantity of cement to be used may be assumed as 330.0 Kg/cum of finished concrete for M-25 grade mix, 340.0 Kg/cum of finished concrete for M-30 grade mix. In case, cement content as worked out by mix design formula varies from above, the necessary adjustment (plus or minus) in the rate of these item will be made on the basis of base price of cement as per schedule 'F' or purchase price of cement whichever is lower) at site plus water charges @1% and contractor's profit and overheads @ 15%.

Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level. Thermo-Mechanically Treated bars of grade Fe-500D or more.

Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete above plinth level. Thermo-Mechanically Treated bars of grade Fe-500 D or more.

Centering and shuttering including strutting, propping etc. and removal of form for all heights :

Foundations, footings, bases of columns, etc. for mass concrete

Walls (any thickness) including attached pilasters, butteresses, plinth and string courses etc.

Suspended floors, roofs, landings, balconies and access platform

Lintels, beams, plinth beams, girders, bressumers and cantilevers

Columns, Pillars, Piers, Abutments, Posts and Struts

Stairs, (excluding landings) except spiral-staircases

Extra for shuttering in circular work (20% of respective centering and shuttering items) Foundations, footings, bases of columns, etc. for mass concrete

Extra for shuttering in circular work (20% of respective centering and shuttering items) Walls (any thickness) including attached pilasters, butteresses,plinth and string courses etc.

Small lintels not exceeding 1.5 m clear span, moulding as in cornices, window sills, string courses, bands, copings, bed plates, anchor blocks and the like

Edges of slabs and breaks in floors and walls Under 20 cm wide

Edges of slabs and breaks in floors and walls Above 20 cm wide

Extra for additional height in centering, shuttering where ever required with adequate bracing, propping etc., including cost of de-shuttering and decentering at all levels, over a height of 3.5 m, for every additional height of 1 metre or part thereof (Plan area to be measured). Suspended floors, roofs, landing, beams and balconies (Plan area to be measured)

Extra for R.C.C./ B.M.C/ R.M.C. work above floor V level for each four floors or part thereof.

Providing and fixing of expansion joint system related with floor location as per drawings and direction of Engineer-In-Charge. The joints system will be of extruded aluminum base members, self aligning / self centering arrangement and support plates etc. as per ASTM B221-02. The system shall be such that it provides floor to floor /floor to wall expansion control system for various vertical locations in load application areas that accommodates multi directional seismic movement without stress to it's components. System shall consist of metal profiles with a universal aluminum base member designed to accommodate various project conditions and finish floor treatments. The cover plate shall be designed of width and thickness required to satisfy projects movement and loading requirements and secured to base members by utilizing manufacturer’s pre-engineered self-centering arrangement that freely rotates / moves in all directions. The Self - centering arrangement shall exhibit circular sphere ends that lock and slide inside the corresponding aluminum extrusion cavity to allow freedom of movement and flexure in all directions including vertical displacement. Provision of Moisture Barrier Membrane in the Joint System to have watertight joint is mandatory requirement all as per the manufactures design and as approved by Engineer -in- Charge. (Material shall conform to ASTM 6063). Floor Joint of upto 100 mm gap

Providing and fixing of expansion joint system related with wall joint (internal/ external) location as per drawings and direction of Engineer-In- Charge. The joints shall be of extruded aluminum base members, self aligning / centering arrangement and support plates as per ASTM B221- 02. The material shall be such that it provides an Expansion Joints System suitable for vertical wall to wall/ wall to corner application, both new and existing construction in office Buildings & complexes with no slipping down tendency amongst the components of the Joint System. The Joint System shall utilize light weight aluminum profiles exhibiting minimal exposed aluminum surfaces mechanically snap locking the multicellular to facilitate movement. (Material shall conform to ASTM 6063.) Wall Joint of upto 100 mm gap

Providing and fixing of expansion joint system of approved make and manufacture for various roof locations as per approved drawings and direction of Engineer-In-Charge. The joints shall be of extruded aluminum base members with, self aligning and self centering arragement support plates as per ASTM B221-02. The system shall be such that it provides water tight roof to roof /roof to corner joint cover expansion control system that is capable of accommodating multidirectional seismic movement without stress to its components. System shall consist of metal profile that incorporates a universal aluminum base member designed to accommodate various project conditions and roof treatments. The cover plate shall be designed of width and thickness required to satisfy movement and loading requirements and secured to base members by utilizing manufacturer’s pre-engineered self-centering arrangement that freely rotates / moves in all directions. The Self centering arrangement shall exhibit circular sphere ends that lock and slide inside the corresponding aluminum extrusion cavity to allow freedom of movement and flexure in all directions including vertical displacement. The Joint System shall resists damage or deterioration from the impact of falling ice, exposure to UV, airborne contaminants and occasional foot traffic from maintenance personnel. Provision of Moisture Barrier Membrane in the Joint System to have water tight joint is mandatory requirement. (Material shall confirm to ASTM 6063.) Roof Joint of upto 100 mm gap

Providing and fixing sheet covering over expansion joints with iron screws as per design. Aluminium fluted strips 3.15 mm thick. 200 mm wide

Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in foundation and plinth in: Cement mortar 1:6 (1 cement : 6 coarse sand)

Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level in all shapes and sizes in : Cement mortar 1:6 (1 cement : 6 coarse sand)

Extra for brick work / AAC block masonry / Tile brick masonry in superstructure above floor V level, for each four floors or part thereof by mechanical means.

Half brick masonry with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in foundations and plinth in : Cement mortar 1:3 (1 cement : 3 coarse sand)

Half brick masonry with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level. Cement mortar 1:3 (1 cement :3 coarse sand)

Extra for half brick masonry in superstructure, above floor V level for every four floors or part thereof by mechanical means.

Extra for providing and placing in position 2 Nos 6mm dia. M.S. bars at every third course of half brick masonry.

Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position with hold fast lugs or with dash fasteners of required dia & length ( hold fast lugs or dash fastener shall be paid for separately). Second class teak wood

Providing and fixing ISI marked flush door shutters conforming to IS : 2202 (Part I) decorative type, core of block board construction with frame of 1st class hard wood and well matched teak 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters. 35 mm thick including ISI marked Stainless Steel butt hinges with necessary screws

Providing and fixing ISI marked flush door shutters conforming to IS : 2202 (Part I) non-decorative type, core of block board construction with frame of 1st class hard wood and well matched commercial 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters: 35 mm thick including ISI marked Stainless Steel butt hinges with necessary screws

Providing & Fixing decorative high pressure laminated sheet of plain / wood grain in gloss / matt/ suede finish with high density protective surface layer and reverse side of adhesive bonding quality conforming to IS : 2046 Type S, including cost of adhesive of approved quality. 1.5 mm thick

Extra for providing lipping with 2nd class teak wood battens 25 mm minimum depth on all edges of flush door shutters (over all area of door shutter to be measured).

Extra for providing vision panel not exceeding 0.1 sqm in all type of flush doors (cost of glass excluded) (overall area of door shutter to be measured):

Extra if louvers (not exceeding 0.2 sqm) are provided in flush door shutters (overall area of door shutters to be measured).

Providing and fixing skirting with Pre-laminated medium density fibre board exterior grade (Grade-I) conforming to IS: 14587:1998 marked, with (one side decorative and other side balancing lamination and edges to be sealed with PVC edge bending tape 2.00 mm thick of approved brand with necessary fixing arrangements and screws, including drilling necessary holes for rawl plugs etc. all complete. 18 mm thick.

Providing and fixing cup board shutters with 25 mm thick veneered particle board IS : 3097 marked, exterior grade (Grade I), of approved make, including IInd class teak wood lipping of 25 mm wide x 12 mm thick with necessary screws and bright finished stainless steel piano hinges, complete as per direction of Engineer-in-Charge. With decorative veneering on one side and commercial veneering on other side

Providing & fixing Toilet Cubicle (model, type Titan SS series of Marino/Green Sturdo Classique-Evergreen Series of Greenply or equivalent) of following standard dimension which includes 600mm door size width made of heat, bacteria, water, chemical, scratch, impact resistant 12mm thick solid compact laminate panels including doors, pilasters & intermediate panels finished with approved shade as per the detail drawings & as per IS 2046 (Indian Standard) and as per fire retardant BS-476/97 standard including providing and fixing in position all necessary hardware made out of Stainless steel (Grade 304) as required including the following minimum hardware: (1) Door Knob (2) Gravity Hinges (3) Thumb turn lockset with Occupancy indicators (4) Coat hooks with Door stopper (5) Adjustable foot/pedestal (6) Top rail. (7) Rubber noise deafening tape (8) Screws & wall Plugs. The top fitting shall consist of top rail which will get fixed as per manufacturer’s specifications. All screws will be of 304 Grade in stainless steel with satin finish. All pilasters are supported by stainless steel Adjustable foot/pedestal as per manufacturer’s specifications. The base of the foot/pedestal will be anchored to the floor. The clearance height will be a maximum of 150mm.

Toilet Cubicle L-shape with standard dimension of 2000 - 2100 mm Height x 900 - 1000 mm Width x 1500mm Depth, which includes 600mm door size width).

Toilet Cubicle I-Shape (Front Partition) with standard dimension of 2000 – 2100 mm Height x 900 - 1000 mm Width, which includes 600mm door size width).

Providing and fixing slimline aluminium extruded section body tubular type universal hydraulic door closer (door weight upto 80 kg) of Dorma / Yale / Assa Abloy / Geze, with double speed adjustment with necessary accessoriesand screws etc. complete to the satisfaction of Engineer-in-charge.

Providing and fixing set of Stainless steel L-shape Mortise Lever Door Handle and Narrow Style Mortice lock in Stainless steel satin finish grade 304 with one side key operation and other side thumb turn operation along with strike plate, front plate, cylinder, keys, necessary screws, etc complete with oval / round rosettes and escutcheon of Dorma / Yale / Assa Abloy / Geze, to the satisfaction of Engineer-in-charge.

Providing and fixing Stainless steel Pull Handle 600mm long, 32 mm dia suitable for glass/wooden/metal doors of Dorma / Yale / Assa Abloy / Geze, with necessary screws etc complete to the satisfaction of Engineer-in-charge. The pull handles should have supporting washer with raised bevelling on the outer surface.

Providing and fixing Stainless steel Pull Handle 300 -350mm long, 22-25 mm dia suitable for wooden doors of Dorma / Yale / Assa Abloy / Geze, with necessary screws etc complete to the satisfaction of Engineer-in-charge. The pull handles should have supporting washer with raised bevelling on the outer surface.

Providing and fixing stainless steel half dome type floor door stopper of Dorma / Yale / Assa Abloy / Geze, with necessary screws etc. complete to the satisfaction of Engineer-in-charge.

Providing and fixing stainless steel tower bolts of Dorma / Yale / Assa Abloy / Geze, with necessary screws etc. complete to the satisfaction of Engineer-in-Charge : 250 mm long

Supply and installation of DORMA / YALE / ASSA ABLOY / Geze Sliding system suitable for door weight upto 120kgs, single door.consisting of the following: Track length=2000mm in Anodised finish Sliding system with clamps, 2 rollers, end stops and accessories. Finish - Anodised Finish. Recessed Oval Flush Pull Handle 1207 SS Mortice sliding door 400 claw bolt, prepared for euro profile cylinder with 55mm backset, 22mm sq forend including strike plate in satin stainless steel. Door will be paid for separately in the basic item

Providing and fixing bright /matt finished Stainless Steel handles of approved quality & make with necessary screws etc all complete. 125 mm

Providing and fixing special quality bright finished brass cupboard or ward robe locks with four levers of approved quality including necessary screws etc. complete. 50 mm

Providing and fixing partition upto ceiling height consisting of G.I. frame and required board, including providing and fixing of frame work made of special section power pressed/ roll form G.I. sheet with zinc coating of 120 gms/sqm(both side inclusive), consisting of floor and ceiling channel 50mm wide having equal flanges of 32 mm and 0.50 mm thick, fixed to the floor and ceiling at the spacing of 610 mm centre to centre with dash fastener of 12.5 mm dia meter 50 mm length or suitable anchor fastener or metal screws with nylon plugs and the studs 48 mm wide having one flange of 34 mm and other flange 36 mm and 0.50 mm thick fixed vertically within flanges of floor and ceiling channel and placed at a spacing of 610 mm centre to centre by 6 mm dia bolts and nuts, including fixing of studs along both ends of partition fixed flush to wall with suitable anchor fastener or metal screws with nylon plugs at spacing of 450 mm centre to centre, and fixing of boards to both side of frame work by 25 mm long dry wall screws on studs, floor and ceiling channels at the spacing of 300 mm centre to centre. The boards are to be fixed to the frame work with joints staggered to avoid through cracks, M.S. fixing channel of 99 mm width (0.9 mm thick having two flanges of 9.5 mm each) to be provided at the horizontal joints of two boards, fixed to the studs using metal to metal flat head screws, including jointing and finishing to a flush finish with recommended jointing compound, jointing tape, angle beads at corners (25 mm x 25 mm x 0.5 mm), joint finisher and two coats of primer suitable for board as per manufacture's specification and direction of engineer in charge all complete. 75mm overall thickness partition with 12.5 mm thick double skin tapered edged plain Gypsum board conforming to IS: 2095: part I

Providing and fixing fire resistant door frame of section 143 x 57 mm having built in rebate made out of 16 SWG G.I. sheet (zinc coating not less than 120 gm/sqm) duly filled with vermuculite based concrete mix, suitable for mounting 60 minutes fire rated door shutters. The frame is fitted with intumuscent fire seal strip of size 10x4 mm (minimum) alround the frame and fixing with dash fastener of approved size and make, including applying a coat of approved brand fire resistant primer etc. complete as per direction of Engineer-in-charge (Dash fastener to be paid for separately).

Providing and fixing expandable fasteners of specified size with necessary plastic sleeves and galvanised M.S. screws including drilling holes in masonry work /CC/ R.C.C. and making good etc. complete. 50 mm long

Providing and fixing 50 mm thick glazed fire resistant door shutters of 60 minutes fire rating conforming to IS:3614 (Part-II), tested and certified as per laboratory approved by Engineer-in-charge, with suitable mounting on door frame, consisting of vertical styles, lock rail, top rail 100 mm wide, bottom rail 200 mm wide, made out of 16 SWG G.I.sheet (zinc coating not less than 120 gm/m2) duly filled FR insulation material and fixing with necessary stainless steel ball bearing hinges of approved make, including applying a coat of approved fire resistant primer etc. all complete as per direction of Engineer-in-charge (panneling to be paid for separately).

Providing and fixing glazing in fire resistant door shutters, fixed panels, ventilators and partitions etc., with G.I. beading of appropriate size, made out of 20 SWG G.I.sheet (zinc coating not less than 120 gm/m2), fire resistant sealant, including applying a coat of approved fire resistant primer on G.I. beading etc., complete all as per direction of Engineer-incharge. With clear fire resistant glass panes 6mm thick of approved brand, having minimum 60 minutes fire resistance

Providing and fixing panic bar / latch (Double point) fitted with a single body, Trim Latch & Lock on back side of the Panic Latch of reputed brand and manufacture to be approved by the Engineer- in- charge, all complete.

Structural steel work in single section, fixed with or without connecting plate, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete.

Providing and fixing hand rail of approved size by welding etc. to steel ladder railing, balcony railing, staircase railing and similar works, including applying priming coat of approved steel primer. M.S. tube

Supply and installation Pipe balustrade system with glass link : Providing DORMA / Dline / Yale / Qrailing modular (weld free, component base) system. 50.8 mm dia x 1.6 mm thick handrail fixed to balustrade of 50.8 mm dia x 1.6 mm thick with top adapter (neck) type fixed with 2 nos. of m4 x 10 mm allen CSK screw. The balustrade fixed to top of the floor, straight or staircase by epoxy chemical grout (chemical grout). The balustrade c/c is 900 to 1000mm. The height of the handrail 1000 mm from FFL. Glass infill of 10 mm thick toughened (monolithic) is fixed to the balustrade with glass link m8 x 25 mm allen cap screw (two per balustrade), complete with all end cap. All the material of handrail, balustrade and components should be of SS 304 grade satin finish. (Please note that no welding of SS pipes will be allowed and work shall get to be done by a specialized agency on modular and component basis). Please note that only length of hand railing will be measured for the payment & rates shall be inclusive of all stainless steel pipes, glass and fittings required vertically or horizontally per running meter of composite section of railing

Supplying and fixing rolling shutters of approved make, made of required size M.S. laths, interlocked together through their entire length and jointed together at the end by end locks, mounted on specially designed pipe shaft with brackets, side guides and arrangements for inside and outside locking with push and pull operation complete, including the cost of providing and fixing necessary 27.5 cm long wire springs manufactured from high tensile steel wire of adequate strength conforming to IS: 4454 - part 1 and M.S. top cover of required thickness for rolling shutters. 80x1.25 mm M.S. laths with 1.25 mm thick top cover

Providing and fixing ball bearing for rolling shutters.

Extra for providing mechanical device chain and crank operation for operating rolling shutters. Exceeding 10.00 sqm and upto 16.80 sqm in the area

Extra for providing grilled rolling shutters manufactured out of 8 mm dia M.S. bar instead of laths as per design approved by Engineer-in- charge, (area of grill to be measured).

Steel work welded in built up sections/ framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required.

In stringers, treads, landings etc. of stair cases, including use of chequered plate wherever required, all complete

In gratings, frames, guard bar, ladder, railings, brackets, gates and similar works

Structural steel work riveted, bolted or welded in built up sections, trusses and framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete.

Providing and fixing mild steel round holding down bolts with nuts and washer plates complete.

Providing and fixing circular/ Hexagonal cast iron or M.S. sheet box for ceiling fan clamp, of internal dia 140 mm, 73 mm height, top lid of 1.5 mm thick M.S. sheet with its top surface hacked for proper bonding, top lid shall be screwed into the cast iron/ M.S. sheet box by means of 3.3 mm dia round headed screws, one lock at the corners. Clamp shall be made of 12 mm dia M.S. bar bent to shape as per standard drawing.

Steel work in built up tubular ( round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer including welding and bolted with special shaped washers etc. complete. Electric resistance or induction butt welded tubes (grade of steel considered YST 310)

Providing and fixing carbon steel galvanised ( minimum coating 5 micron) dash fastener of 10 mm dia double threaded 6.8 grade (yield strength 480 N/mm2), counter sunk head, comprising of 10 m dia polyamide PA 6 grade sleeve, including drilling of hole in frame , concrete/ masonry, etc. as per direction of Engineer-in-charge. 10 x 160 mm

Suppling, Drilling/Cleaning hole and fixing HILTI or equivalent make heavy duty ETA Approved HVA-E Chemical Anchor of appropriate size and fixing plates subsequently. Anchor comprises of HVU flexible foil capsule that contains styrene free Urethane Metacrylate resin, hardener, quartz, sand/corrundum and HAS-E theaded rod of minimum 5.8 steel grade, galvanised to minimum 5 microns. Manufacture should submit Anchor Design report based on design loads & other parameters as provided by consultants. Chemical anchors should be designed in accordance with EOTA-TR-029 “guidelines for anchorage of chemical anchors for use in concrete” for approval. Application at site should be done as per manufacturer guidelines. M16 of standard length

62 mm thick cement concrete flooring with concrete hardener topping, under layer 50 mm thick cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20mm nominal size) and top layer 12mm thick cement hardener consisting of mix 1:2 (1 cement hardener mix : 2 graded stone aggregate, 6mm nominal size) by volume, hardening compound mixed @ 2 litre per 50 kg of cement or as per manufacture’s specifications. This includes cost of cement slurry, but excluding the cost of nosing of steps etc. complete.

Cement concrete flooring 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate) finished with a floating coat of neat cement, including cement slurry, but excluding the cost of nosing of steps etc. complete. 40 mm thick with 20 mm nominal size stone aggregate

Cement plaster skirting up to 30 cm height, with cement mortar 1:3 (1 cement : 3 coarse sand), finished with a floating coat of neat cement. 18 mm thick.

Kota stone slab flooring over 20 mm (average) thick base laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab, including rubbing and polishing complete with base of cement mortar 1 : 4 (1 cement : 4 coarse sand) : 25 mm thick

Kota stone slabs 20 mm thick in risers of steps, skirting, dado and pillars laid on 12 mm (average) thick cement mortar 1:3 (1 cement: 3 coarse sand) and jointed with grey cement slurry mixed with pigment to match the shade of the slabs, including rubbing and polishing complete.

Extra for pre finished nosing in treads of steps of Kota stone/ sand stone slab.

Extra for Kota stone/ sand stone in treads of steps and risers using single length up to 1.05 metre.

Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS: 15622, of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand), jointing with grey cement slurry @ 3.3kg/sqm including grouting the joints with white cement and matching pigments etc., complete. Size of Tile 600x600 mm

Providing and laying Vitrified tiles in different sizes (thickness to be specified by manufacturer), with water absorption less than 0.08 % and conforming to I.S. 15622, of approved make, in all colours & shade, in skirting, riser of steps, over 12 mm thick bed of cement mortar 1:3 (1 cement: 3 coarse sand), jointing with grey cement slurry @ 3.3kg/sqm including grouting the joint with white cement & matching pigments etc. complete. Size of Tile 600x600 mm

Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS: 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade complete.

Providing and laying Ceramic glazed floor tiles of size 300x300 mm (thickness to be specified by the manufacturer) of 1st quality conforming to IS : 15622 of approved make in colours such as White, Ivory, Grey, Fume Red Brown, laid on 20 mm thick cement mortar 1:4 (1 Cement : 4 Coarse sand), jointing with grey cement slurry @ 3.3kg/sqm including pointing the joints with white cement and matching pigment etc., complete.

Marble work gang saw cut (polished and machine cut) of thickness 18 mm for wall lining (veneer work), backing filled with a grout of average 12 mm thick in cement mortar 1:3 (1 cement : 3 coarse sand), including pointing with white cement mortar 1:2 (1 white cement : 2 marble dust) with an admixture of pigment to match the marble shade (To be secured to the backing by means of cramps, which shall be paid for separately). Raj Nagar Plain white marble/ Udaipur green marble/ Zebra black marble. Area of slab over 0.50 sqm

Providing and fixing 18 mm thick gang saw cut, mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels.

Area of slab upto 0.50 sqm

Area of slab over 0.50 sqm.

Providing edge moulding to 18 mm thick marble stone counters, Vanities etc., including machine polishing to edge to give high gloss finish etc. complete as per design approved by Engineer-in-Charge. Granite work.

Extra for providing opening of required size & shape for wash basin/ kitchen sink in kitchen platform, vanity counter and similar location in marble/ Granite/ stone work, including necessary holes for pillar taps etc. including moulding, rubbing and polishing of cut edges etc. complete.

Extra for fixing marble /granite stone, over and above corresponding basic item, in facia and drops of width upto 150 mm with epoxy resin based adhesive, including cleaning etc. complete.

Chequerred precast cement concrete tiles 22 mm thick in footpath & courtyard, jointed with neat cement slurry mixed with pigment to match the shade of tiles, including rubbing and cleaning etc. complete, on 20 mm thick bed of cement mortar 1:4 (1 cement: 4 coarse sand). Medium shade pigment using 50% white cement 50% Grey cement

Providing and laying flamed finish Granite stone flooring in required design and patterns, in linear as well as curvilinear portions of the building all complete as per the architectural drawings with 18 mm thick stone slab over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with cement slurry and pointing with white cement slurry admixed with pigment of matching shade including rubbing, curing and polishing etc. all complete as specified and as directed by the Engineer-in-Charge : Flamed finish granite stone slab Jet Black, Cherry Red, Elite Brown, Cat Eye or equivalent.

Providing and laying Polished Granite stone flooring in required design and patterns, in linear as well as curvilinear portions of the building, all complete as per the architectural drawings, with 18 mm thick stone slab over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand), laid and jointed with cement slurry and pointing with white cement slurry admixed with pigment of matching shade, including rubbing, curing and polishing etc. all complete as specified and as directed by the Engineer-in-Charge. Polished Granite stone slab jet Black, Cherry Red, Elite Brown, Cat Eye or equivalent.

Providing and fixing Ist Quality 18mm thick mirror polished granite stone in skirting, dado and cladding fixed on 12mm (average) thick cement mortar 1:3 (1 cement : 3 coarse sand) and jointed with white cement slurry mixed with pigment to match the shade of slab including curing, cleaning complete at all levels. Mirror polished granite stone slab of any approved colour and shade

Extra for providing and applying minimum two coats of Ferrocrete/MYKLaticrete/STP Sealer or approved equivalent on the back surface and sides of the Granite with a brush or roller to act as a barrier coat against stains, discoloration and effloroscence including cleaning the surface with brush or roller, mopping with moist cloth and allowing it to dry before application all complete as per direction of Engineer-in-charge.(Raw Surface) Note : Granite stone flooring shall be paid for separately under respective item.

Extra for providing and applying minimum two coats of Ferrocrete/MYKLeticrete/STP Impregnator sealer or approved equivalent with a brush / roller on the top surface of the Granite to act as a barrier coat against stains, soling, discoloration and effloroscence including cleaning the surface with brush or roller, mopping with moist cloth and allowing it to dry before application all complete as per direction of Engineer-in-charge.(Polished Surface) Note : Granite stone flooring shall be paid for separately under respective item.

Providing and fixing Access Floor panel of 600x600x32 mm medium grade Filled Steel anti static high pressure Lamination of 800H grade (FS800H). Access Floor panel shall be steel welded construction with an enclosed bottom pan with uniform pattern of 64 hemispherical cones. The top and bottom plates of Steel Gauges: top 0.6 mm and bottom 0.7 mm fused spot welded together (minimum 64 welds in each dome and 20 welds along each flange). The panel should be corrosion resistant epoxy coated for lifetime rust protection and cavity formed by the top and bottom plate is filled with Pyrogrip noncombustible Portland cementitious core mixed with lightweight foaming compound. The access floor shall be factory finished with Anti-static High Pressure laminate with Non Warp technology upto 1mm thickness for superior adhesion and Surface flatness within 0.75mm.The panel is to withstand a Concentrated Load of 363 kgs applied on area 25mm x 25mm without collapse in the centre of the panel which is placed on four steel blocks. The panel will withstand and Uniformly Distributed Load (UDL) minimum 1250 kg/sqm and, an impact load of 50kg all complete as per the approved manufacturers specification and as per the direction of Engineer-in-charge. All specification must be printed on the side of the panel to ensure the quality of the product. 450 mm Finished Floor Height (FFH).

Providing and fixing mineral fibre false ceiling tiles at all heights of size 595X595mm of approved texture, design and pattern. The tiles should have Humidity Resistance (RH) of 99%, Light Reflectance > 85%, Thermal Conductivity k = 0.052 - 0.057 w/m K, Fire Performance as per (BS 476 pt - 6 &7)in true horizontal level suspended on interlocking T-Grid of hot dipped all round galvanized iron section of 0.33 mm thick (galvanized @120 gsm ) comprising of main T runners of 15x32 mm of length 3000 mm, cross T of size 15x32mm of length 1200 mm and secondary intermediate cross T of size 15x32 mm of length 600 mm to form grid module of size 600x600 mm suspended from ceiling using galvanized mild steel item (galvanised @80gsm) 50 mm long 8mm outer diameter M-6 dash fasteners, 6 mm diameter fully threaded hanger rod upto 1000 mm length and L-shape level adjuster of size 85x25x2 mm, spaced at 1200 mm centre to centre along main ‘T’. The system should rest on periphery walls /partitions with the help of GI perimeter wall angle of size24x24X3000 mm made of 0.40 mm thick sheet, to be fixed to the wall with help of plastic rawl plug at 450 mm centre to centre & 40 mm long dry wall S.S. screws. The exposed bottom portion of all T-sections used in false ceiling support system shall be prepainted with polyester baked paint, for all heights. The work shall be carried out as per specifications, drawings and as per directions of the engineer-in-charge. With 16 mm thick beveled tegular mineral fibre false ceiling tile (NRC 0.55 to 0.6)

Providing and fixing false ceiling at all height including providing and fixing of frame work made of special sections, power pressed from M.S. sheets and galvanized with zinc coating of 120 gms/sqm (both side inclusive) as per IS : 277 and consisting of angle cleats of size 25 mm wide x 1.6 mm thick with flanges of 27 mm and 37mm, at 1200 mm centre to centre, one flange fixed to the ceiling with dash fastener 12.5 mm dia x 50mm long with 6mm dia bolts, other flange of cleat fixed to the angle hangers of 25x10x0.50 mm of required length with nuts & bolts of required size and other end of angle hanger fixed with intermediate G.I. channels 45x15x0.9 mm running at the spacing of 1200 mm centre to centre, to which the ceiling section 0.5 mm thick bottom wedge of 80 mm with tapered flanges of 26 mm each having lips of 10.5 mm, at 450 mm centre to centre, shall be fixed in a direction perpendicular to G.I. intermediate channel with connecting clips made out of 2.64 mm dia x 230 mm long G.I. wire at every junction, including fixing perimeter channels 0.5 mm thick 27 mm high having flanges of 20 mm and 30 mm long, the perimeter of ceiling fixed to wall/partition with the help of rawl plugs at 450 mm centre, with 25mm long dry wall screws @ 230 mm interval, including fixing of gypsum board to ceiling section and perimeter channel with the help of dry wall screws of size 3.5 x 25 mm at 230 mm c/c, including jointing and finishing to a flush finish of tapered and square edges of the board with recommended jointing compound , jointing tapes , finishing with jointing compound in 3 layers covering upto 150 mm on both sides of joint and two coats of primer suitable for board, all as per manufacturer's specification and also including the cost of making openings for light fittings, grills, diffusers, cutouts made with frame of perimeter channels suitably fixed, all complete as per drawings, specification and direction of the Engineer in Charge but excluding the cost of painting with : 12.5 mm thick tapered edge gypsum plain board conforming to IS: 2095- Part I

Providing & fixing false ceiling at all height including providing & fixing of framework made of special section, power pressed from M.S. sheets and galvanised with zinc coating of 120 gms/ sqm (both side inclusive) as per IS : 277 and consisting of angle cleat of size 25mm wide x 1.6mm thick with flanges of 27mm and 37mm, at 1200mm c/c, one flange fixed to the ceiling with dash fastener 12.5mm dia x 50mm long with 6mm dia bolts, other flange of cleat fixed to the angle hangers of 25 x10 x0.50mm of required length with nuts & bolts of required size and other end of angle hanger fixed with intermediate G.I chanels 45 x15 x 0.90mm running at the spacing of 1200 mm c/c, to which the ceiling section 0.5mm thick bottom wedge of 80mm with tapered flanges of 26 mm each having lips of 10.5mm, at 450mm c/c, shall be fixed in a direction perpendicular to G.I intermediate channel with connecting clip made out of 2.64mm dia x 230mm long G.I wire at every junction, including fixing perimeter channels 0.50mm thick 27mm high having flanges of 20mm and 30mm long, the perimeter of ceiling fixed to wall/ partitions with the help of Rawl plugs at 450mm centre, with 25mm long dry wall screws @ 230mm interval, including fixing of Calcium Silicate Board to ceiling section and perimeter channels with the help of dry wall screws of size 3.5 x25mm at 230mm c/c, including jointing & finishing to a flush finish of tapered and square edges of the board with recommended jointing compounds, jointing tapes,finishing with jointing compounds in three layers covering up to 150mm on both sides of joints and two coats of primer suitable for boards, all as per manufacture's specification and also including the cost of making opening for light fittings, grills, diffusers, cut outs made with frame of perimeter channels suitably fixed, all complete as per drawings, specificaton and direction of the Engineer in charge but excluding the cost of painting with: 8 mm thick Calcium Silicate Board made with Calcareous & Siliceous materials reinforced with cellulose fiber manufactured through autoclaving process.

Providing and fixing cup board shutters with 25 mm thick veneered particle board IS : 3097 marked, exterior grade (Grade I), of approved make, including IInd class teak wood lipping of 25 mm wide x 12 mm thick with necessary screws and bright finished stainless steel piano hinges, complete as per direction of Engineer-in-Charge. With non decorative veneering on both sides

Providing and fixing of Double skin Insulated sheeting system with top sheet shall be of color coated zincalume/galvalume coated trapezoidal profile sheet, having nominal 980-1020 mm effective cover width and nominal 28-30 mm deep ribs with subtle square fluting in four to five pan at nominal 195-250 mm centre-to-centre and having thickness of minimum 0.45mm Base Metal thickness (BMT)/0.5mm Total coated thickness (TCT) of Grade 550MPa. The feed material for top & liner sheet is manufactured out of minimum 0.45 mm Base Metal Thickness (BMT), Hi-strength steel with min. 550 MPa yield strength, metallic hot dip coated with zinc-aluminium alloy (55% Aluminium, 45% Zinc)) AZ150 (Min. 150gms/sq.mt total on both sides)as per AS 1397 ( & of approved color ) oven-baked steel quality paint coat as per AS/NZS 2728 of TATA BlueScope Steel or JSW or ISPAT or BHUSHAN STEEL make or equivalent system . The paint shall have a total coating thickness of nominal 35μm, comprising of nominal 20μm exterior coat on top surface and nominal 5 μm reverse coat on back surface over nominal 5μm primer coat on both surfaces of approved colour shade by Engineer-In-Charge. The top profile sheet shall be roll formed to required lengths to suit shop drawings as approved by Engineer-In-Charge. Top Sheets shall be fixed to subgirt of 1.5mm,& same shall be fastened with nominal 40 μm zinc coated or nominal 25 μm zinc-tin alloy coated, Hex head, self-drilling screw Class 3 fasteners of approved make (Buildex / Landmark / Corroshield or equivalent) with EPDM washer as per the requirement considering the profile shape and design load. The fastener size shall be calculated as per the design or manufacturers recommendations. Internal Liner sheet shall also be screwed through ribs/crest only to purlins / girt with screws as per above mentioned specifications & the fastener size shall be calculated as per the design and approved by EIC.For roof fixing, screws should be placed through crest. The contractor is to take approval on the sheet profile, design and installation methodology before installation of the sheets from the Engineer-In-Charge. Top sheet and bottom sheet shall have brand marking of the manufacturer details on the back of the sheet at regular intervals for confirming genuinity of the material. The steel manufacturer’s test certificate for the chemical and mechanical properties of steel must be submitted to the Engineer In Charge prior to installation. The two sheets shall have a layer 100 mm thick Glasswool Non-combustible grade (2 layers of 50mm each) 48 Kg/m3 density insulation with one side FSK/Al foil. The entire Double skin system is installed over the structure purlin. GI subgirt of 1.5mm thick 50x100x50mm required in between the sheets to hold the outer sheet. The main color of liner sheet has to be visible from inside. The entire Double skin system is installed over the structure purlin. GI subgirt of 1.5mm thick 50x100x50mm required in between the sheets to hold the outer sheet. (Item includes designing, supplying, installation and fixing of profiled metal sheeting including cost of system accessories insulation, vapour barrier, liner sheet, flashing, fasteners, gaskets, brackets screws rivets, sealants, inner closure fillers, fixtures, all machineries and all taxes, i.e sales tax, excise duty, customs duty, VAT tax, etc, complete). The above work is to be carried out by a specialised agency approved by the Engineer-in-charge.

Supply & Installation of Multi cell/tight cell Polycarbonate Panel System of minimum thickness 12mm of approved colour and shade confirming to specifications mentioned below: Panel will be minimum 12mm thick single panel. The weight of the panel will be 2500 - 2650 gram per square meter. Panel Width shall not be less than 600 mm to ensure best performance for wind uplift, vibration, oil canning and visual appearance. The panels shall be uniform in color with an integral Tight-Cell core. Panels shall be manufactured with Vertical Standing Seam at both sides of the panel. Snap-on connector to interlock the panels shall have a grip-lock locking mechanism to ensure maximum uplift capability. Panel shall be factory sealed/end welded panels with additional End-cap/Aluminium U-Profile (mill finish) for ends. Panels shall be co-extruded UV protected. Panel shall be co-extruded with special anti glare compound to make it anti-glare/soft light to prevent glare and sun streaks. All ridges will be covered with ridge capping as approved. The polycarbonate panels shall be bent to required profile (linear or curvilinear) and fixed in position, to the structural steel framework, using self-driving self-tapping screws, Aluminium or other profiles, accessories etc. as per the approved architectural drawings. For payment purpose the area of finished polycarbonate sheet fixed in position shall only be measured.

Providing and fixing precoated galvanised iron profile sheets (size, shape and pitch of corrugation as approved by Engineer-in-charge) 0.50 mm (+ 0.05 %) total coated thickness with zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length upto 12 metre or as desired by Engineerin -charge. The sheet shall be fixed using self drilling /self tapping screws of size (5.5x 55 mm) with EPDM seal, complete upto any pitch in horizontal/ vertical or curved surfaces, excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required.

Providing and fixing Heat Resistant Terrace Tiles (300 mm x 300 mm x 20 mm) with SRI (solar refractive index) > 78, solar reflection > 0.70 and initial emittance > 0.75 on waterproof and sloped surface of terrace, laid on 20 mm thick cement sand mortar in the ratio of 1:4 (1 cement : 4 coarse sand) and grouting the joints with mix of white cement & marble powder in ratio of 1:1, including rubbing and polishing of the surface upto 3 cuts complete, including providing skirting upto 150 mm height along the parapet walls in the same manner.

Providing and fixing 50 mm thick extruded polystyrene rigid insulation board of required size underdeck on ceiling surface, complying with ISO 4898:2008 & ASTM C 578-08b - type VI, having thermal conductivity of 0.0289 W/m K as per ASTM C 578 (measured as per IS 3346), compressive strength of > 350 kPa listed as per ASTM D 1621, density of 34-36 kg/m³ as per ASTM D 1622, water absorption < 1% by volume as per ASTM D 2842, oxygen index of 24.1 to 28.1 listed as per ASTM D 2863, cell size 0.4 mm of dia (max) as per ASTM D 3576. Fire retardent property as per DIN 4102, Part 1 of class B2 and as per ASTM E84 class A, fixed with suitable water based adhesive and fastener, complete in all respect as per the directions of Engineer-in-Charge.

Providing and fixing precoated galvanised steel sheet roofing accessories 0.50 mm (+ 0.05 %) total coated thickness, Zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns using self drilling/ self tapping screws complete : Flashings/ Aprons.( Upto 600 mm)

6 mm cement plaster of mix : 1:3 (1 cement : 3 fine sand)

12 mm cement plaster of mix : 1:6 (1 cement: 6 fine sand)

15 mm cement plaster on the rough side of single or half brick wall of mix : 1:6 (1 cement: 6 fine sand)

15 mm cement plaster 1:3 (1 cement: 3 coarse sand) finished with a floating coat of neat cement on the rough side of single or half brick wall.

18 mm cement plaster in two coats under layer 12 mm thick cement plaster 1:5 (1 cement : 5 coarse sand) finished with a top layer 6 mm thick cement plaster 1:6 (1 cement : 6 fine sand).

Extra for providing and mixing water proofing material in cemen plaster work in proportion recommended by the manufacturers.

Extra for plastering exterior walls of height more than 10 m from ground level for every additional height of 3 m or part thereof.

Forming groove of uniform size in the top layer of plaster as per approved pattern using wooden battens, nailed to the under layer including removal of wooden battens, repair to the edges of panels and finishing the groove complete as per specifications and direction of the Engineer-in-charge : 12 mm wide and 6 mm deep groove

Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete.

Applying priming coats with primer of approved brand and manufacture, having low VOC (Volatile Organic Compound ) content.

With water thinnable cement primer on wall surface having VOC content less than 50 grams/litre

With ready mixed red oxide zinc chromatic on steel / iron works having VOC content less than 250 grams/ litre

Finishing walls with textured exterior paint of required shade : New work (Two or more coats applied @ 3.28 ltr/10 sqm) over and including priming coat of exterior primer applied @ 2.20kg/10 sqm

Providing and fixing 24 gauge 8 mm size galvanised chicken wire mesh of approved width at junctions of concrete and brick work and other locations called for including necessary laps and U shape galvanised wire nails.

Wall painting with premium acrylic emulsion paint of interior grade, having VOC (Volatile Organic Compound ) content less than 50 grams/ litre of approved brand and manufacture, including applying additional coats wherever required to achieve even shade and colour. Two coats.

Distempering with 1st quality acrylic distemper, having VOC (Volatile Organic Compound ) content less than 50 grams/ litre, of approved brand and manufacture, including applying additional coats wherever required, to achieve even shade and colour. Two coats

White washing with lime to give an even shade : New work (three or more coats)

Painting with Polyurethane finish paint including priming with Epoxy Zinc Phosphate Primer of approved brand and manufacture and of required shade and colour on steel galvanized iron / steel works complete, as per manufacturer's specification to give an even shade including abrasive blasting to minimum Sa 2-1/2 (ISO 8501-1:1988) or SSPC-SP6. a) Two or more coats on new work

Painting with synthetic enamel paint, having VOC (Volatile Organic Compound) content less than 150 grams/ litre, of approved brand and manufacture, including applying additional coats wherever required to achieve even shade and colour. Two coats

Providing and applying required coats of fireproof intumescent paint of Phoenix / Asian Paints / Jotun / approved equivalent of required thickness onto structural steel members as per manufacturer's specifications for a 1 - hour including priming with Epoxy Zinc Phosphate Primer of approved brand and manufacture and of required shade and colour with low VOC content (<250 gm/Ltr) on steel galvanized iron / steel works complete, as per manufacturer's specification to give an even shade including abrasive blasting to minimum Sa 2-1/2 (ISO 8501-1:1988) or SSPC-SP6. a) Two or more coats on new work

French spirit polishing : Two or more coats on new works including a coat of woodfiller

Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / paneling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing, paneling and dash fasteners to be paid for separately) :

For fixed portion Powder coated aluminium (minimum thickness of powder coating 50 micron)

For shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber / neoprene gasket required (Fittings shall be paid for separately) Powder coated aluminium (minimum thickness of powder coating 50 micron)

Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of Engineer-in-charge . (Cost of aluminium snap beading shall be paid in basic item): With float glass panes of 5.50 mm thickness

Providing and fixing 12 mm thick prelaminated particle board flat pressed three layer or graded wood particle board conforming to IS: 12823 Grade l Type ll, in panelling fixed in aluminum doors, windows shutters and partition frames with C.P. brass / stainless steel screws etc. complete as per architectural drawings and directions of Engineer-in-charge. Pre-laminated particle board with decorative lamination on both sides

Providing and fixing bright finished brass 100 mm mortice latch and lock, ISI marked, with six levers and a pair of anodised (anodic coating not less than grade AC 10 as per IS : 1868) aluminium lever handles of approved quality with necessary screws etc. complete.

Filling the gap in between aluminium/ stone/ wood frame and adjacent RCC/ Brick/ Stone/ wood/ Ceramic/ Gypsum work by providing weather/structural non sag elastomeric PU sealant over backer rod of approved quality as per architectural drawings and direction of Engineer-in-charge complete, complying to ASTM C920, DIN 18540-F & ISO 11600 Upto 5mm depth and 5 mm width

Providing and fixing aluminium casement windows fastener of requiredlength for aluminium windows with necessary screws etc. complete. Powder coated minimum thickness 50 micron aluminium

Providing and fixing stainless steel (SS 304 grade) adjustable friction windows stays of approved quality with necessary stainless steel screws etc. to the side hung windows as per direction of Engineerin- charge complete. 355 X 19 mm

Providing & fixing 12 mm thick frosted toughened glass urinal partitions of size 900mm x 450mm fixed to wall with SS clamps, with necessary screws, etc. complete to the satisfaction of Engineer in Charge

Designing, fabricating, testing, protection, installing and fixing in position semi (grid) unitized system of structural glazing (with open joints) for linear as well as curvilinear portions of the building for all heights and all levels, including: (a) Structural analysis & design and preparation of shop drawings for the specified design loads conforming to IS 875 part III (the system must passed the proof test at 1.5 times design wind pressure without any failure), including functional design of the aluminum sections for fixing glazing panels of various thicknesses, aluminium cleats, sleeves and splice plates etc. gaskets, screws, toggles, nuts, bolts, clamps etc., structural and weather silicone sealants, flashings, fire stop (barrier)- cum-smoke seals, microwave cured EPDM gaskets for water tightness, pressure equalisation & drainage and protection against fire hazard including: (b) Fabricating and supplying serrated M.S. hot dip galvanised / Aluminium alloy of 6005 T5 brackets of required sizes, sections and profiles etc. to accommodate 3 Dimentional movement for achieving perfect verticality and fixing structural glazing system rigidly to the RCC/ masonry/structural steel framework of building structure using stainless steel anchor fasteners/ bolts, nylon seperator to prevent bimetallic contacts with nuts and washers etc. of stainless steel grade 316, of the required capacity and in required numbers. (c) Providing and filling, two part pump filled, structural silicone sealant and one part weather silicone sealant compatible with the structural silicone sealant of required bite size in a clean and controlled factory / work shop environment , including double sided spacer tape, setting blocks and backer rod, all of approved grade, brand and manufacture, as per the approved sealant design, within and all around the perimeter for holding glass. (d) Providing and fixing in position flashings of solid aluminium sheet 1 mm thick and of sizes, shapes and profiles, as required as per the site conditions, to seal the gap between the building structure and all its interfaces with curtain glazing to make it watertight. (e) Making provision for drainage of moisture/ water that enters the curtain glazing system to make it watertight, by incorporating principles of pressure equalization, providing suitable gutter profiles at bottom (if required), making necessary holes of required sizes and of required numbers etc. complete. This item includes cost of all inputs of designing, labour for fabricating and installation of aluminium grid, installation of glazed units, T&P, scaffolding and other incidental charges including wastages etc., enabling temporary structures and services, cranes or cradles etc. as described above and as specified. The item includes the cost of getting all the structural and functional design including shop drawings checked by a structural designer, dully approved by Engineer-in-charge. The item also includes the cost of all mock ups at site, cost of all samples of the individual components for testing in an approved laboratory, field tests on the assembled working structural glazing as specified, cleaning and protection till the handing over of the building for occupation. In the end, the Contractor shall provide a water tight structural glazing having all the performance characteristics etc. all complete as required, as per the Architectural drawings, as per item description, as specified, as per the approved shop drawings and as directed by the Engineer- in-Charge. Note:- 1. The cost of providing extruded aluminium frames, shadow boxes, extruded aluminium section capping for fixing in the grooves of the curtain glazing and vermin proof stainless steel wire mesh shall be paid for separately under relevant items under this sub- head. However, for the purpose of payment, only the actual area of structural glazing (including width of grooves ) on the external face shall be measured in sqm. up to two decimal places. Note:- 2. The following performance test are to be conducted on structural glazing system if area of structural glazing exceeds 2500 Sqm from the certified laboratories accreditated by NABL(National Accreditation Board for Testing and Calibration Laboratories), Department of Science & Technologies, India. Cost of testing is payable separately. The NIT approving authority will decide the necessity of testing on the basis of cost of the work, cost of the test and importance of the work. Performance Testing of Structural glazing system Tests to be conducted in the NBL Certified laboratories (1) Performance Laboratory Test for Air Leakage Test (-50pa to - 300pa) & (+50pa to +300pa) as per ASTM E-283-04 testing method for a range of testing limit 1 to 200 mVhr (2) Static Water Penetration Test. (50pa to 1500pa) as per ASTME- 331-09 testing method for a range up to 2000 ml. (3) Dynamic Water Penetration (50pa to 1500pa) as per AAMA 501.01- 05 testing method for a range upto 2000 ml (4) Structural Performance Deflection and deformation by static air pressure test (1.5 times desing wind pressure without any failure) as per ASTME-330-10 testing method for a range upto 50 mm (5) Seismic Movement Test (upto 30 mm) as per AAMA 501.4-09 testing method for Qualitative test. Tests to be conducted on site. (6) Onsite Test for Water Leakage for a pressure range 50 kpa to 240 kpa (35psi) upto 2000 ml

Providing and supplying aluminium extruded tubular and other aluminium sections as per the architectural drawings and approved shop drawings , the aluminium quality as per grade 6063 T5 or T6 as per BS 1474,including super durable powder coating of 60-80 microns conforming to AAMA 2604 of required colour and shade as approved by the Engineer-in-Charge. (The item includes cost of material such as cleats, sleeves, screws etc. necessary for fabrication of extruded aluminium frame work. Nothing extra shall be paid on this account).

Extra for openable side / top hung vision glass panels (IGUs) including providing and supplying at site all accessories and hardwares for the openable panels as specified and of the approved make such as heavy duty stainless steel friction hinges, min 4 -point cremone locking sets with stainless steel plates, handles, buffers etc. including necessary stainless steel screws/ fasteners, nuts, bolts, washers etc. all complete as per the Architectural drawings, as per the approved shop drawings, as specified and as directed by the Engineer- in-Charge.

Providing, assembling and supplying vision glass panels (IGUs) comprising of hermetically-sealed laminated insulated glass (double glazed) vision panel units of size and shape as required and specified, comprising of 30.52 mm thick Hermetically sealed insulated glass comprising with 12.52 mm thick laminated glass (6 mm Clear Heat Strengthened Glass + 1.52mm PVB Layer + 5 mm Heat Strengthened Low e Glass Planetherm of Saint Gobain or equivalent) + 12mm air gap + 6 mm thick heat soaked, toughened clear glass, having properties as per technical specifications , all complete job as per satisfaction of Engineer-In-charge . (Payment for fixing of IGU Panels in the glazing system is included in cost of relevant item ) For payment, the area of glass shall be measured in sqm.

Providing, assembling and supplying vision glass panels 24mm thick comprising of 6 mm heat soaked, toughened Low e Glass Planetherm of Saint Gobain or equivalent with soft reflective coating + 12mm airgap + 6mm heat soaked, toughened clear glass having properties as per technical specifications all complete job as per satisfaction of Engineer-In-charge . (Payment for fixing of IGU Panels in the glazing system is included in cost of relevant item ) For payment, the area of glass shall be measured in sqm.

Designing, fabricating, testing, installing and fixing in position Curtain Wall with Aluminium Composite Panel Cladding, with open grooves for linear as well as curvilinear portions of the building , for all heights and all levels etc. including: (a) Structural analysis & design and preparation of shop drawings for pressure equalisation or rain screen principle as required, proper drainage of water to make it watertight including checking of all the structural and functional design. (b) Providing, fabricating and supplying and fixing panels of aluminium composite panel cladding in pan shape in metalic colour of approved shades made out of 4mm thick aluminium composite panel material consisting of 3mm thick FR grade mineral core sandwiched between two Aluminium sheets (each 0.5mm thick). The aluminium composite panel cladding sheet shall be coil coated, with Kynar 500 based PVDF / Lumiflon based fluoropolymer resin coating of approved colour and shade on face # 1 and polymer (Service) coating on face # 2 as specified using stainless steel screws, nuts, bolts, washers, cleats, weather silicone sealant, backer rods etc. (c) The fastening brackets of Aluminium alloy 6005 T5 / MS with Hot Dip Galvanised with serrations and serrated washers to arrest the wind load movement, fasteners, SS 316 Pins and anchor bolts of approved make in SS 316, Nylon separators to prevent bi-metallic contacts all complete required to perform as per specification and drawing The item includes cost of all material & labour component, the cost of all mock ups at site, cost of all samples of the individual components for testing in an approved laboratory, field tests on the assembled working curtain wall with aluminium composite panel cladding, cleaning and protection of the curtain wall with aluminium composite panel cladding till the handing over of the building for occupation. Base frame work for ACP cladding is payable under the relevant aluminium item.s The Contractor shall provide curtain wall with aluminium composite panel cladding, having all the performance characteristics all complete , as per the Architectural drawings, as per item description, as specified, as per the approved shop drawings and as directed by the Engineer-in-Charge. However, for the purpose of payment, only the actual area on the external face of the curtain wall with Aluminum Composite Panel Cladding (including width of groove) shall be measured in sqm. up to two decimal places."

Providing and fixing Aluminium louvers fixed including main framing, sub frame, necessary hardware as per the elevation, sections and detailed drawings of approved make / colour consisting of panel 84 mm wide x 16mm deep x 1.0mm thick with round edges panel length upto 6mtrs coil coated on a continuous paint line double baked and roll formed from enameled corrosion Resistance Aluminum Alloy 6063 T6 for higher strength and good Roll forming characteristics. Panels shall be clipped at a distance of 70 to 85 mm to baked enameled Aluminium panel stringer 33mm wide and 65mm deep x 1.5 mm thick in a standard length of 5mtrs made of double baked enameled Aluminium Alloy 6063 T6 white to hold the panel in a module of 70 to 75mm centre to centre as per the direction of Engineer in charge complete . All profiles shall be pure polyester powder coated according to I.S. :137871:1993, 60 microns thick in approved shade / colour.

Providing and fixing up to 3.5 m high FRAMELESS GLASS INTERNAL PARTITIONS with 12mm clear toughened glass or as per elevation drawings enclosed with approved make PT patch fittings, die cast fittings with stainless steel cover of DORMA /LISUS / or approved equivalent make fixed with s.s. screws or with fixing clips.The top of the glass shall be fixed to the ceiling with Wall Connecting profile(non security version) of Dorma make. Necessary filling up gaps at junction, at top, bottom and sides with required weather silicon with backer rod shall be inserted between aluminium channel and glass as well as both inside and outside around the periphery of the glass to make the glazing air and water tight as as per specification and direction of Engineer in charge. The installation of glass partition with stainless steel fixtures be as per drawings along with approved grade of silicon sealant of "Dow corning - USA" or "WACKER - Germany". The partition shall be aligned for the entire height and for the entire width by laser beam equipment to ensure 100 percent 'X' axis and 'Y' axis alignment. The complete design fixing details / design will be done as per approval of Engineer-in charge. (The work is to be got executed from approved specialized agency to the satisfaction of Engineer in charge).

Providing and fixing 12 mm thick frameless toughened glass door shutter of approved brand and manufacture, including providing and fixing top & bottom pivot & spring type fixing arrangement and making necessary holes etc. for fixing required door fittings, all complete as per direction of Engineer-in-charge (Door handle, lock and stopper etc.to be paid separately).

Providing and fixing the following stainless steel hardware suitable for 12 mm thick frameless toughened glass door shutter of Dorma / Yale including all necessary screws, washers, etc, all complete as per direction of Engineer-in-charge 2 pairs of Stainless steel Pull Handle 300 -350mm long, 22-25 mm dia 2 nos. of Stainless Steel lock (lockable at floor level) 2 nos. of stainless steel half dome type floor door stopper . 2 nos, of top patch & top pivot 2 nos. bottom patch 2 nos. floor spring for 100 kg door

Providing and laying integral cement based water proofing treatment including preparation of surface as required for treatment of roofs, balconies, terraces etc consisting of following operations: (a) Applying a slurry coat of neat cement using 2.75 kg/sqm of cement admixed with water proofing compound conforming to IS. 2645 and approved by Engineer-in-charge over the RCC slab including adjoining walls upto 300 mm height including cleaning the surface before treatment. (b) Laying brick bats with mortar using broken bricks/brick bats 25 mm to 115 mm size with 50% of cement mortar 1:5 (1 cement : 5 coarse sand) admixed with water proofing compound conforming to IS : 2645 and approved by Engineer-in-charge over 20 mm thick layer of cement mortar of mix 1:5 (1 cement :5 coarse sand) admixed with water proofing compound conforming to IS : 2645 and approved by Engineer-in-charge to required slope and treating similarly the adjoining walls upto 300 mm height including rounding of junctions of walls and slabs. (c) After two days of proper curing applying a second coat of cement slurry using 2.75 kg/ sqm of cement admixed with water proofing compound conforming to IS : 2645 and approved by Engineerin- charge. (d) Finishing the surface with 20 mm thick jointless cement mortar of mix 1:4 (1 cement :4 coarse sand) admixed with water proofing compound conforming to IS : 2645 and approved by Engineerin- charge including laying glass fibre cloth of approved quality in top layer of plaster and finally finishing the surface with trowel with neat cement slurry and making pattern of 300x300 mm square 3 mm deep. (e) The whole terrace so finished shall be flooded with water for a minimum period of two weeks for curing and for final test. All above operations to be done in order and as directed and specified by the Engineer-in-Charge :

Making khurras 45x45 cm with average minimum thickness of 5 cm cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate of 20 mm nominal size) over P.V.C. sheet 1 m x1 m x 400 micron, finished with 12 mm cement plaster 1:3 (1 cement : 3 coarse sand) and a coat of neat cement, rounding the edges and making and finishing the outlet complete.

Providing and laying integral cement based treatment for water proofing on the vertical surface by fixing specified stone slab 22 mm to 25 mm thick with cement slurry mixed with water proofing compound conforming to IS:2645 in recommended proportions with a gap of 20 mm (minimum) between stone slabs and the receiving surfaces and filling the gaps with neat cement slurry mixed with water proofing compound and finishing the exterior of stone slab with cement mortar 1:3 (1 cement : 3 coarse sand) 20 mm thick with neat cement punning mixed with water proofing compound in recommended proportion complete at all levels and as directed by Engineer-in-charge : Using rough Kota stone

Providing and laying integral cement based treatment for water proofing on horizontal surface at all depth below ground level for under ground structures as directed by Engineer-in-Charge and consisting of : (i) Ist layer of 22 mm to 25 mm thick approved and specified rough stone slab over a 25 mm thick base of cement mortar 1:3 (1 cement : 3 coarse sand) mixed with water proofing compound conforming to IS:2645 in the recommended proportion over the leveling course (leveling course to be paid separately). Joints sealed and grouted with cement slurry mixed with water proofing compound. (ii) 2nd layer of 25 mm thick cement mortar 1:3 (1 cement: 3 coarse sand) mixed with water proofing compound in recommended proportions. (iii) Finishing top with stone aggregate of 10 mm to 12 mm nominal size spreading @ 8 cudm/sqm thoroughly embedded in the 2nd layer. Using rough kota stone.

Providing and Placing in position suitable PVC water stops conforming to IS:12200 for construction/ expansion joints between two RCC members and fixed to the reinforcement with binding wire before pouring concrete etc. complete : Serrated with central bulb (225 mm wide, 8-11 mm thick)

Providing and laying water proofing treatment to vertical and horizontal surfaces of depressed portions of W.C., kitchen and the like consisting of: (i) Ist course of applying cement slurry @ 4.4 kg/sqm mixed with water proofing compound conforming to IS 2645 in recommended proportions including rounding off junction of vertical and horizontal surface. (ii) IInd course of 20 mm cement plaster 1:3 (1 cement : 3 coarse sand) mixed with water proofing compound in recommended proportion including rounding off junction of vertical and horizontal surface. (iii) IIIrd course of applying blown or residual bitumen applied hot at 1.7 kg. per sqm of area. (iv) IVth course of 400 micron thick PVC sheet. (Overlaps at joints of PVC sheet should be 100 mm wide and pasted to each other with bitumen @ 1.7 kg/ sqm).

Preparation and consolidation of sub grade with power road roller of 8 to 12 tonne capacity after excavating earth to an average of 22.5 cm depth, dressing to camber and consolidating with road roller including making good the undulations etc. and re-rolling the sub grade and disposal of surplus earth with lead upto 50 metres.

Extra for compaction of earth work in embankment under optimum moisture conditions to give at least 95% of the maximum dry density (proctor density).

Providing, laying, spreading and compacting graded stone aggregate (size range 53 mm to 0.075 mm ) to wet mix macadam (WMM) specification including premixing the material with water at OMC in for all leads & lifts, laying in uniform layers with mechanical paverfinisher in sub- base / base course on well prepared surface and compacting with vibratory roller of 8 to 10 tonne capacity to achievethe desired density, complete as per specifications and directions of Engineer-in-Charge.

Painting runway/taxi track/apron marking with adequate nos of coats to give uniform finish with road marking paint of superior make as approved by the Engineer-in-charge, i/c cleaning the surface of all dirt, scales, oil, grease and other foreign mater;al etc. and lining out complete. New work (Two or more coats)

Providing and laying 60mm thick factory made cement concrete interlocking paver block of M -30 grade made by block making machine with strong vibratory compaction, of approved s;ze, design & shape, laid in required colour and pattern over and including 50mm thick compacted bed of coarse sand, filling the joints with line sand etc. all complete as per the direction of Engineer-in-charge.

Supplying and laying of 60 mm thick M30 grade grass paver block ( perforated Cement Concrete block) of size 25x25x6cm to 30x30x6cm with perforation of size 8x8x6 cm and of approved design/ shape laid in required colour and pattern manufactured using homogeneous designed concrete mix, vibrocompaction process, weigh batching and high speed pan mixing suitably cured in controlled conditions and laying the same over a 50mm thick compacted sand bedding layer level and slope including filling the joints with sand all etc., complete as per the direction of Engineer in charge.

Providing and laying Pavement Quality Concrete (PQC) produced in a batching plant having a Characteristic flexural strength i.e. minimum flexural strength of 4.1 MPa at 28 days using 350 Kg of ordinary Portland cement of 43 grade per cum of finished concrete, fine aggregate, graded stone aggregates of 40 mm nominal size in appropriate proportion as per specification and job mix formula, laid in panels as per drawings/design as approved by the Engineer-In-Charge using including making necessary provision for expansion joint, curing, etc. complete as per direction of Engineer-in-Charge and particular specifications. The item for execution shall also include the following operations: i) Mechanically cutting dummy joints 3mm wide x 1/3rd thickness of slab which is subsequently widened to 10mm for the top 25mm depth and construction joints 10mm wide x 25mm deep as per specification. ii) Filling Polysulphide sealant in dummy, construction and expansion joints including providing closed-cell Polyethylene foam back-up rod, and painting side of joints with Polysulphide primer, etc. complete (to be paid separately under revelant item.)

Construction of dry lean cement concrete sub base over a prepared sub-grade with coarse and fine aggregate conforming to IS:383, the size of coarse aggregate not exceeding 25 mm, aggregate cement ratio not to exceed 15:1, aggregate gradation after blending to be as per specifications, cement content not to be less than 150 Kg/cum, optimum moisture content to be determined during trial length construction, concrete strength not to be less than 10 Mpa at 7 days, mixed in a batching plant, transported to site, for all leads & lifts, laid with a mechanical paver, compacting with 8-10 tonne vibratory roller, finishing and curing etc. complete as per direction of Engineerin- charge.

Dismantling of flexible pavement (bituminous courses) by mechanical means and disposal of dismantled material up to a lead of 1 kilometre, as per direction of Engineer-in-charge.

Providing and laying Polythene sheet 400 micron thick, conforming to IS2508 antifriction layer on the sub base course complete as per specification with specified overlap between adjacent strips and transeverse joint (only plan area is to be measured for payment).

Providing and fixing in position pre-moulded joint filler in expansion joints.

Providing and laying in position Polysulphide sealant of approved make conforming to BS-5212-1990 or IS: 11433-1995 in expansion/ construction/dummy joints including rounding off edges, applying 2 coats of approved primer compatible with the brand of Polysulphide and preparing the surface and applying masking tape along the edge of joint to prevent accidental spillage of sealant on top surface and to give neat finish to the sealant and removing the masking tape after application of sealant etc. complete as per direction of Engineer in- Charge & particular specifications. [Note: For purpose of payment, quantity (Length x Width x Depth) of Polysulphide sealant only will be measured.]

Providing and laying non-pressure NP2 class (light duty) R.C.C. pipes with collars jointed with stiff mixture of cement mortar in the proportion of 1:2 (1 cement : 2 fine sand) including testing of joints etc. complete : 300 mm dia. R.C.C. pipe

Constructing brick masonry manhole in cement mortar 1:4 ( 1 cement : 4 coarse sand ) with R.C.C. top slab with 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size), foundation concrete 1:4:8 mix (1 cement : 4 coarse sand : 8 graded stone aggregate 40 mm nominal size), inside plastering 12 mm thick with cement mortar 1:3 (1 cement : 3 coarse sand) finished with floating coat of neat cement and making channels in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) finished with a floating coat of neat cement complete as per standard design : Inside size 120x90 cm and 90 cm deep including C.I. cover with frame (heavy duty) 560 mm internal diameter, total weight of cover and frame to be not less than 208 kg (weight of cover 108 kg and weight of frame 100 kg) : With common burnt clay F.P.S. (non modular) bricks of class designation 7.5

Extra for depth for manholes : Size 120x90 cm With common burnt clay F.P.S. (non modular) bricks of class designation 7.5

Providing and fixing of Roller blinds (Blackout type) of Mac Décor / Hunter Douglas / Vista / approved equivalent on the windows at all heights, all materials and labour etc., complete in all respects as per directions of Engineer having following specifications:- i) Composition: Fibre Glass / Vinyl Coated Fibre Glass ii) Thickness:- 0.32 - 0.40 mm iii) Weight: 330 - 410 gm/sqm iv) Degree of Opacity - 100% Material & Color shade will be as per sample approved by Engineer in Charge.

Providing & fixing of white vitreous China wall mounting cascade type water closet with cistern (Hindware Rubbic Cat No 92064 +92124 or Jaquar Kubix Cat No KUS-WHT-35851SN or approved equivalent) with CP bolts, nuts, CI chair hanging arrangements, bakelite seat & cover with CP hinges & rubber buffers, CP brass screw, washer with all accessories with WC connector with Rubber Lip / Buffer and side gap filled with silicon sealant wherever required. Including brass / SS screws and washer complete including cutting, making good the walls, floors, slab wherever required as per direction of Engineer-Incharge.

Providing and fixing of C.P. brass Central Hole Basin Mixer without Popup Waste System with all fittings and accessories as per direction of Engineer-Incharge. (Jaquar Cat No. PRS-031 or equivalent)

Providing & fixing of white vitreous china under counter oval wash basin/circular basin (Hindware 10049 / Parryware / Jaquar FLS-WHT-5701 or approved equivalent) with CP brass waste assembly( Jaquar cat No. ALD 705), 450mm long CP copper connections pipes (Jaquar Cat No. ALD 803AB or approved equivalent), wall flanges and rubber adapters for waste connection complete including CI/MS brackets duly painted, nuts, washers, cutting and making good the walls floors wherever required as per direction of Engineer-Incharge.

Providing & fixing white vitreous china flat back urinal (Hindware 96008 / Jaquar Cat No URS-WHT-13253O or approved equivalent) comprising of all plumbing items including pressmatic flush valve (Jaquar Cat No. PRS 073 or approved equivalent), CP brass flush pipe with CP brass elbow, CP brass spreader, CP wall flange, and any other item required to provide satisfactory functioning including necessary wall cutting / chasing and making good, as required for urinal flushing complete as mentioned above as per direction of Engineer-Incharge.

Providing & fixing C.P. hand shower with lever control (health faucet) (Jaquar Cat. No. ALD-577 or approved equivalent) and flexible hose 1 .2 m long connection with C.P. holder for hand spray complete in all respects as per direction of Engineer-Incharge.

Providing and fixing C.P. brass angle valve for basin mixer and geyser points of approved quality conforming to IS:8931 15mm nominal bore

Providing & fixing liquid soap dispenser (Jaquar Cat No. 1135N / Parko or approved equivalent) as per direction of Engineer-Incharge.

Providing and fixing Bottle Trap (Jaquar Cat. No. ALD-769L250x190 or approved equivalent) and other ancillary fittings, cutting and making good the walls wherever required complete as per directions of Engineer-Incharge.

Providing and fixing complete set of sanitary fixtures for handicapped toilets, make of Hindware Cat. no. 70003) / or approved equivalent comprising of EWC - P , Cistern, Seat Cover, Twin Flush Fittings, Wash Basin 450x300, Half pedestal, 1 faucet with spatula lever, 1 hinged rail and 2 grab bars, including cutting and making good the walls and floors wherever required complete as per directions of Engineer in charge.

Providing and fixing 600x450 mm beveled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete.

Providing & Fixing water closet squatting pan (Indian W.C. pan) with 100 mm sand cast iron P or S trap, Ceramic dual flushing cistern with all fittings & fixture complete including cutting and making good the walls & floors wherever required. White vitreous china Orissa pattern W.C. pan with integral type foot rests (Hindware : 20004 Orissa Pan 58x44 B + Cistern & Lid 21029 / approved equivalent )

Providing and fixing Stainless Steel A ISi 304 (18/8) kitchen sink as per IS: 13983 with C.I. brackets and stainless steel plug 40 mm, including painting of fittings and brackets, cutting and making good the walls wherever required : (a) Kitchen sink with drain board 510x1040 mm bowl depth 225 mm

Providing and fixing, testing and commissioning of C.P. brass single hole sink mixer with CP wall flange, swinging spout complete as required and making good as per direction of Engineer-in-Charge (Jaquar Cat No. FLR-5007B / approved equivalent)

Providing and fixing CP brass towel rail 600 mm long of approved make complete with CP brackets fixed to wooden cleats with CP brass screws.(Jaquar Cat No. ACN-1111NM / approved equivalent)

Providing and fixing toilet paper holder. (Jaquar Continental 1151 N / approved equivalent)

Providing, fixing, testing and commissioning of two way C.P. brass bib cock with C.P. wall flange of approved quality (Jaquar Cat No. CON- 041KN / approved equivalent)

Providing and fixing C.P. brass bib cock of approved quality conforming to IS:8931 : 15 mm nominal bore

Providing and fixing C.P. brass long nose bib cock of approved quality conforming to IS standards and weighing not less than 810 gms. 15 mm nominal bore

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge. Concealed work, including cutting chases and making good the walls etc.

15 mm nominal outer dia Pipes (SDR-11)

20 mm nominal outer dia. pipes (SDR-11)

25 mm nominal outer dia. pipes (SDR-11)

32 mm nominal outer dia. pipes (SDR-11)

40 mm nominal outer dia. pipes (SDR-11)

50 mm nominal outer dia. pipes (SDR-11)

Providing and fixing CPVC (SDR 11) ball valves tested to a pressure of 15 Kg / Sqcm including flanges / union, etc. complete as required.

15mm dia

20mm dia

25mm dia

32mm dia

Providing and fixing G.I. pipes complete with G.I. fittings and clamps, i/c cutting and making good the walls etc. Internal work - Exposed on wall

15 mm dia. nominal bore

20 mm dia. nominal bore

25 mm dia. nominal bore

32 mm dia. nominal bore

40 mm dia. nominal bore

50 mm dia. nominal bore

Painting G.I. pipes and fittings with two coats of anti-corrosive bitumastic paint of approved quality :

15 mm diameter pipe

20 mm diameter pipe

25 mm diameter pipe

32 mm diameter pipe

40 mm diameter pipe

50 mm diameter pipe

Providing & fixing full way lever operated forged brass / Gun Metal ball valve of brass body with forged brass hard chrome plated steel ball tested to a pressure not less than 15 Kg / sqcm with threaded / flanged joints complete with nuts, bolts, gaskets, washers etc. as per direction of Engineer-Incharge.

25 mm dia.

32 mm dia.

40 mm dia.

50mm dia.

Providing and fixing Butterfly valve (upto 150mm dia. with band lever operation & above with gear box operation) with SS-304 disc. Tested to a pressure not less than 15 Kg/sq.cm including rubber gaskets, flanges, nuts, bolts, washers & painting complete as required.

80 mm dia.

Providing and fixing G.I. pipes complete with G.I. fittings including trenching and refilling etc. (external work)

15 mm dia. nominal bore

32 mm dia. nominal bore

40 mm dia. nominal bore

50 mm dia. nominal bore

65 mm dia. nominal bore

80 mm dia. nominal bore

Providing and filling sand of grading zone V or coarser grade alround the G.I. pipes in external work.

32 mm diameter pipe

40 mm diameter pipe

50 mm diameter pipe

65 mm diameter pipe

80 mm diameter pipe

Constructing masonry Chamber 60x60x75 cm inside, in brick work in cement mortar 1:4 (1 cement : 4 coarse sand) for sluice valve, with C.I. surface box 100mm top diameter, 160 mm bottom diameter and 180 mm deep ( inside) with chained lid and RCC top slab 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20mm nominal size ) , i/c necessary excavation, foundation concrete 1:5:10 (1 cement : 5 fine sand : 10 graded stone aggregate 40 mm nominal size) and inside plastering with cement mortar 1:3 (1 cement : 3 coarse sand) 12 mm thick, finished with a floating coat of neat cement complete as per standard design : With common burnt clay F.P.S.(non modular) bricks of class designation 7.5

Constructing masonry Chamber 30 x 30 x 55 cm, inside with 75 class designation brick work in cement mortar 1:4 (1 cement : 4 fine sand) for sluice valve, with C.I. surface box 100mm top diameter, 160 mm bottom diameter and180 mm deep (inside) with chain lid and RCC top slab 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20mm nominal size) necessary excavation foundation concrete 1:5:10 (1 cement : 5 fine sand : 10 graded stone aggregate 40 mm nominal size) and inside plastering with cement mortar 1:3 (1 cement :3 coarse sand) 12 mm thick finished with a floating coat of neat cement complete as per standard design. With common burnt clay F.P.S.(non modular) bricks of class designation 7.5

Providing and fixing enclosed type water meter (bulk type) conforming to IS : 2373 and tested by Municipal Board complete with bolts, nuts, rubber insertions etc. (The tall pieces if required will be paid separately) 80 mm dia. nominal bore

Providing and fixing uPVC pipe confirming to IS: 4985 of 6kg per Sqcm for for garden irrigation system including all fittings i/c trenching, refilling & testing of joints complete as per direction of Engineer in Charge. (External Work)

25 mm diameter pipe

63 mm diameter pipe

75 mm diameter pipe

Supplying and fixing in position 15mm dia. lawn hydrants consisting of 15mm dia. ball valve, GI nipple and treaded hose receiver complete as required.

Providing and placing on terrace (at all floor levels) polyethylene water storage tank, IS : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank. Circular tank

Providing and fixing soil, waste and vent pipes : 100 mm dia. (Centrifugally cast (spun) iron socketed pipe as per IS:3989)

Providing and fixing M.S holder-bat clamps of approved design to Sand Cast iron/ cast iron (spun) pipe embedded in and including cement concrete blocks 10x10x10 cm of 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20mm nominal size) including cost of cutting holes and making good the walls etc. - for 100 mm dia. pipe

Providing and fixing bend of required degree with access door, insertion rubber washer 3 mm thick, bolts and nuts complete : 100 mm - Sand cast iron S&S as per IS-3989

Providing and fixing plain bend of required degree: 100 mm - Sand cast iron S&S as per IS:3989

Providing and fixing heel rest sanitary bend: 100 mm dia. - sand cast iron S&S as per IS-3989

Providing and fixing single equal plain junction of required degree with access door, insertion rubber washer 3mm thick, bolts and nuts complete:100x100x100mm - sand cast iron S&S as per IS-3989

Providing and fixing terminal guard.: 100 mm - sand cast iron S&S as per IS-3989

Providing and fixing collar: 100 mm -Sand cast iron S&S as per IS-3989

Providing lead caulked joints to sand cast iron /centrifugally cast (spun) iron pipes and fittings of diameter: 100 mm

Providing and fixing M.S. stays and clamps for sand cast iron / centrifugally cast (spun) iron pipes of diameter : 100 mm

Painting sand cast iron / centrifugally cast (spun) iron soil, waste vent pipes and fittings with paint of any colour such as chocolate, grey, or buff etc. over a coat of primer (of approved quality) for new work -100 mm diameter pipe

Providing and fixing UV stabilized uPVC rain water pipes conforming to IS:4985 (working pressure 6 kg/sqcm.) including jointing with seal ring conforming to IS : 5382 leaving 10 mm gap for thermal expansion. (I) Single socketed pipes

160 mm diameter (6 kg/sq. cm)

200 mm diameter (6 kg/sq. cm)

Providing and fixing on wall face unplasticised - PVC moulded or fabricated fittings / accessories for unplasticised Rigid PVC rain water pipes, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion Single tee with door

Providing and fixing trap of self cleasing design with screwed down or hinged with or without vent arm complete, including cost of cutting and making good the walls and floors. - 100 mm inlet and 100 mm outlet Sand cast iron S&S as per IS: 3989

Providing and fixing G.I. inlet fitting with 1 or 2 inlets fabricated from 100 mm dia. G.I. pipes and welded G.I. sockets fixed to C.I. trap with lead caulked joint and set in cement concrete as per drawing complete as per direction of Engineer-Incharge.

Providing and fixing floor drain made out of 100x50 mm G.I. Elbow connected to G.I. Pipe complete as per direction of Engineer-Incharge.

Providing and fixing Heavy class SS grating with Cockroach proof SS strainer of approved design including setting in floor with cement motor to match with floor finish as per direction of Engineer-Incharg .- Size 100 mm dia.

Providing and fixing G.I. Pipes for waste complete with G.I. Fittings and clamps, including cutting and making good the walls etc. (Internal work) Exposed on wall

32 mm dia. nominal bore

50 mm dia. nominal bore

Painting GI pipes and fittings with two coats of anti-corrosive bitumastic paint of approved quality.

32 mm dia. nominal bore

50 mm dia. nominal bore

Providing and fixing clean out/floor clean out plug consist of CI bend & GI socket heavy class with cap & key for opening male threaded cap etc. including lead caulked to CI pipes complete in all respects as per drawing/ sample approved by Engineer -in -Charge FCO (floor clean out plug shall be flushed with floor finish).: 100 mm dia.

Providing laying and jointing glazed stoneware pipesclass SP-1 with stiff mixture of cement mortar in the pro-portion of 1:1 (1 cement : 1 fine sand) including testing of joints etc. complete.

150 mm diameter

250 mm diameter

Providing and laying non pressure NP2 class (Light duty) R.C.C. pipes with coller jointed with stiff mixture cement mortar in the proportion of 1:2 (1 cement: 2 fine sand) including testing of joints etc. complete.

150 mm dia.

300 mm dia.

Providing and laying cement concrete 1:5:10 mix (1 cement: 5 coarse sand: 10 graded stone aggregate 40 mm nominal size) all round of S.W. / RCC pipes including bed concrete as per standard design. 150 mm dia.

Providing and laying cement concrete 1:5:10 (1cement: 5 coarse sand: 10 graded stone aggregate 40 mm nominal size) up to haunches of S.W. /RCC pipes including bed concrete as per standard design.

150 mm dia.

300 mm dia.

Constructing brick masonry circular type manhole 0.91m internal dia. at bottom and 0.56 m dia. at top in cement mortar 1:4 (1cement: 4coarse sand), inside cement plaster 12 mm thick with cement mortar 1:3 (1 cement: 3 coarse sand) finished with a floating coat of neat cement, foundation concrete 1:3:6 mix (1 cement: 3 coarse sand: 6 graded stone aggregate 40 mm nominal size), and making necessary channel in cement concrete 1:2:4 (1 cement :2 coarse sand : 4 graded stone aggregate 20 mm nominal size) finished with a floating coat of neat cement as per standard design. 0.91 m deep with S.F.R.C cover and frame (Heavy duty, HD-20 grade designation) 560 mm internal diameter conforming to I.S.12592, total weight of cover and frame not to be less than 182 kg. fixed in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) including centering, shuttering all complete.(Excavation, foot rests and 12mm thick cement plaster at the external surface shall be paid for separately) : With common burnt clay F.P.S. (non modular) bricks of class designation 7.5

Extra depth for circular type manhole 0.91 m internal dia. (at bottom ) 0.91 to 1.67 m With common burnt clay F.P.S. (non modular) bricks of class designation 7.5

Constructing brick masonry road gully chamber 50x45x60 cm with bricks in cement mortar 1:4 (1 cement : 4 coarse sand) including 500x450 mm pre-cast R.C.C. horizontal grating with frame complete as per standard design : With common burnt clay F.P.S. (non modular) bricks of class designation 7.5

Extra depth beyond 45 cm of brick masonry chamber: For 455 x 610 mm size With common burnt clay F.P.S. (non modular) bricks of class designation 7.5

Providing and fixing square-mouth S.W. gully trap class SP-1 complete with C.I. grating brick masonry chamber with water tight C.I. cover with frame of 300 x300 mm size (inside) the weight of cover to be not less than 4.50 kg and frame to be not less than 2.70 kg as per standard design: 180x150 mm size P type With common burnt clay F.P.S. (non modular) bricks of class designation 7.5

Extra depth for manholes: Size 120x 90 cm With common burnt clay F.P.S. (non modular) bricks of class designation 7.5

Providing and fixing factory made precast RCC perforated drain covers, having concrete of strength not less than M-25, of size 1000 x 450x50 mm, reinforced with 8 mm dia four nos longitudinal & 9 nos cross sectional T.M.T. hoop bars, including providing 50 mm dia perforations @ 100 to 125 mm c/c, including providing edge binding with M.S. flats of size 50 mm x 1.6 mm complete, all as per direction of Engineerin- charge.

Providing orange colour safety foot rest of minimum 6 mm thick plastic encapsulated as per IS : 10910, on 12 mm dia steel bar conforming to IS: 1786, having minimum cross section as 23 mx25 mm and over all minimum length 263 mm and width as 165 mm with minimum 112 mm space between protruded legs having 2 mm tread on top surface by ribbing or chequering besides necessary and adequate anchoring projections on tail length on 138 mm as per standard drawing and suitable to with stand the bend test and chemical resistance test as per specifications and having manufacture's permanent identification mark to be visible even after fixing, including fixing in manholes with 30x20x15 cm cement concrete block 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) complete as per design.

Boring/drilling bore well of required dia for casing/ strainer pipe, by suitable method prescribed in IS: 2800 (part I), including collecting samples from different strata, preparing and submitting strata chart/ bore log, including hire & running charges of all equipments, tools, plants & machineries required for the job, all complete as per direction of Engineer-in-charge, upto 90 metre depth below ground level. All types of soil 300 mm dia

Supplying, assembling, lowering and fixing in vertical position in bore well, unplasticized PVC medium well casing (CM) pipe of required dia, conforming to IS: 12818, including required hire and labour charges, fittings & accessories etc. all complete, for all depths, as per direction of Engineer -in-charge. 150 mm nominal size dia

Supplying, assembling, lowering and fixing in vertical position in bore well unplasticized PVC medium well screen (RMS) pipes with ribs, conforming to IS: 12818, including hire & labour charges, fittings & accessories etc. all complete, for all depths, as per direction of Engineer-in-charge. 150 mm nominal size dia

Supplying, filling, spreading & leveling stone boulders of size range 5 cm to 20 cm, in recharge pit, in the required thickness, for all leads & lifts, all complete as per direction of Engineer-in-charge.

Supplying, filling, spreading & leveling gravels of size range 5 mm to 10 mm, in the recharge pit, over the existing layer of boulders, in required thickness, for all leads & lifts, all complete as per direction of Engineer-in-charge.

Supplying, filling, spreading & leveling coarse sand of size range 1.5 mm to 2 mm in recharge pit, in required thickness over gravel layer, for all leads & lifts, all complete as per direction of Engineer -incharge.

Gravel packing in tubewell construction in accordance with IS: 4097, including providing gravel fine/ medium/ coarse, in required grading & sizes as per actual requirement, all complete as per direction of Engineer-in-charge.

Providing and fixing Bail plug/ Bottom plug of required dia to the bottom of pipe assembly of tubewell as per IS:2800 (part I). 150 mm dia

Providing and fixing in position pre-cast R.C.C. manhole cover and frame of required shape and approved quality EHD - 35 Circular shape 560 mm internal dia

Providing and fixing 3M Frosted Sparkle Graphic Film over the designated locations with wet applications at all floors in any design and pattern complete as per the direction and satisfaction of Engineer-in- charge. (No deductions shall be made for the blank areas in the pattern. only film area will be measured)

Manufacturing, supplying and fixing retro reflective overhead signage boards made up of 2 mm thick aluminium sheet, face to be fully covered with high intensity and encapsulated lens type heat activated retro reflective sheeting conforming to type - III of ASTM-D-4956-01 as approved by Engineer-in-charge, letters, borders etc. as per IRC : 67-2001 in silver white with blue colour back ground and with high intensity grade, pasted on substrate by pressure sensitive adhesive backing which shall be activated by applying pressure conforming to class II of ASTM-D-4956-01 and fixing the same to the plate of structural frame work by means of suitable sized aluminium alloys, rivets or bolts & nuts @ 300 mm centre to centre all along the periphery as well as in two vertical rows along with theft resistant measures, including the cost of painting with two or more coats of epoxy paint in grey colour on the back side of aluminium sheet including appropriate priming coat. The rate includes the cost of rounding off the corners, lowering down the structural frame work from the gantry, fixing and erecting the same in position all complete as per drawings, specification and direction of the engineer-incharge.( Structural frame work including M.S. plate to be provided separately. Rectangular area of the sheet only shall be measured for payment). Overhead informatory road signage

Manufacturing, supplying and fixing retro reflective sign boards made up of 2 mm thick aluminium sheet, face to be fully covered with high intensity encapsulated type heat activated retro reflective sheeting conforming to type - IV of ASTM-D 4956-01 in blue and silver white or other colour combination including subject matter, message (bilingual), symbols and borders etc. as per IRC ; 67:2001, pasted on substrate by an adhesive backing which shall be activated by applying heat and pressure conforming to class -2 of ASTM-D-4956-01 and fixing the same with suitable sized aluminium alloy rivets @ 20 cm c/c to back support frame of M.S. angle iron of size 25x25x3 mm along with theft resistant measures, mounted and fixed with 2 Nos. M.S. angles of size 35x35x5 mm to a vertical post made up to M.S. Tee section ISMT 50x50x6 mm welded with base plate of size 100x100x5 mm at the bottom end and including making holes in pipes, angles flats, providing & fixing M.S. message plate of requiredsize, steel work to be painted with two or more coats of synthetic enamel paint of required shade and of approved brand & manufacture over priming coat of zinc chromate yellow primer (vertical MS-Tee support to be painted in black and white co lours).Backside of aluminium sheet to be painted with two or more coats of epoxy paint over and including appropriate priming coat including all leads and lifts etc. complete as per drawing, specification and direction of Engineer--in-charge. Mandatory/ Regulatory sign boards of 900 mm diametre with support length of 3750 mm

Manufacturing, supplying and fixing retro reflective sign boards made up of 2 mm thick aluminium sheet, face to be fully covered with high intensity encapsulated type heat activated retro reflective sheeting conforming to type - IV of ASTM-D 4956-01 in blue and silver white or other colour combination including subject matter, message (bilingual), symbols and borders etc. as per IRC ; 67:2001, pasted on substrate by an adhesive backing which shall be activated by applying heat and pressure conforming to class -2 of ASTM-D-4956-01 and fixing the same with suitable sized aluminium alloy rivets @ 20 cm c/c to back support frame of M.S. angle iron of size 25x25x3 mm along with theft resistant measures, mounted and fixed with 2 Nos. M.S. angles of size 35x35x5 mm to a vertical post made up to M.S. Tee section ISMT 50x50x6 mm welded with base plate of size 100x100x5 mm at the bottom end and including making holes in pipes, angles flats, providing & fixing M.S. message plate of requiredsize, steel work to be painted with two or more coats of synthetic enamel paint of required shade and of approved brand & manufacture over priming coat of zinc chromate yellow primer (vertical MS-Tee support to be painted in black and white co lours).Backside of aluminium sheet to be painted with two or more coats of epoxy paint over and including appropriate priming coat including all leads and lifts etc. complete as per drawing, specification and direction of Engineer--in-charge. Cautionary /warning sign boards of equilateral triangular shape having each side of 900 mm with support length of 3650 mm

Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed steel conduit, with modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable etc. as required. Group C

Wiring for group controlled (looped) light point/fan point/exhaust fan point/ call bell point (without independent switch etc.) with 1.5 sq. mm FRLS PVC insulated copper conductor single core cable in surface/ recessed steel conduit, and earthing the point with 1.5 sq. mm FRLS PVC insulated copper conductor single core cable etc. as required. Group C

Wiring for twin control light point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed steel conduit, 2 way modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm. FRLS PVC insulated copper conductor single core cable etc as required.

Wiring for light/ power plug with 2X4 sq. mm FRLS PVC insulated copper conductor single core cable in surface/ recessed steel conduit alongwith 1 No 4 sq. mm FRLS PVC insulated copper conductor single core cable for loop earthing as required.

Wiring for light/ power plug with 4X4 sq. mm FRLS PVC insulated copper conductor single core cable in surface/ recessed steel conduit alongwith 2 Nos. 4 sq. mm FRLS PVC insulated copper conductor single core cable for loop earthing as required.

Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed steel conduit as required

2 X 1.5 sq. mm +1 X 1.5 sq. mm earth wire

2 X 2.5 sq. mm +1 X 2.5 sq. mm earth wire

2 X 4 sq. mm +1 X 4 sq. mm earth wire

2 X 6 sq. mm +1 X 6 sq. mm earth wire

Supplying and drawing following sizes of FRLS PVC insulated copper conductor, single core cable in the existing surface/ recessed steel/ PVC conduit as required. 3 x 1.5sqmm

Supplying and fixing of following sizes of steel conduit along with accessories in surface/recess including painting in case of surface conduit, or cutting the wall and making good the same in case of recessed conduit as required.

Supplying and fixing metal box of following sizes (nominal size) on surface or in recess with suitable size of phenolic laminated sheet cover in front including painting etc as required.

100 mm X 100 mm X 60 mm deep

150 mm X 150 mm X 60 mm deep

200 mm X 250 mm X 60 mm deep

250 mm X 300 mm X 60 mm deep

Supplying and fixing 2 module stepped type electronic fan regulator on the existing modular plate switch box including connections but excluding modular plate etc. as required.

Supplying and fixing modular blanking plate on the existing modular plate & switch box excluding modular plate as required.

Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 3 pin 5/6 amps modular socket outlet and 5/6 amps modular switch, connection etc. as required. (For light plugs to be used in non residential buildings).

Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 6 pin 5/6 & 15/16 amps modular socket outlet and 15/16 amps modular switch, connection etc. as required.

Supply, installation, testing & commissioning of Universal touch Dimmer with range 1VA-150VA for LED fixtures including GI box and faceplate complete as required similar to Legrand Cat No. 573465 or Equivalent.

Supplying and drawing co-axial TV cable RG-6 grade, 0.7 mm solid copper conductor PE insulated, shielded with fine tinned copper braid and protected with PVC sheath in the existing surface/ recessed steel/ PVC conduit as required.

Supplying and drawing of UTP 4 pair CAT 6 LAN Cable in the existing surface/ recessed steel/ PVC conduit as required. 1 Run of cable

Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required.

Telephone socket outlet (RJ-11)

TV antenna socket outlet

Data outlet one module for Data Points (RJ-45)

Supplying and fixing following size/ modules, GI box alongwith modular base & cover plate for modular switches in recess etc as required. 1 or 2 Module (75mm X 75mm)

Supplying and fixing following way, single pole and neutral, sheet steel, MCB distribution board, 240 V, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator)

6 way, Double door

8 way, Double door

Supplying and fixing following way, horizontal type three pole and neutral, sheet steel, MCB distribution board, 415 V, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/ Isolator)

4 way (4 + 12), Double door

6 way (4 + 18), Double door

8 way (4 + 24), Double door

12 way (4 + 36), Double door

Supplying and fixing of following ways surface/ recess mounting, vertical type, 415 V, TPN MCB distribution board of sheet steel, dust protected, duly powder painted, inclusive of 200 A, tinned copper bus bar, common neutral link, earth bar, din bar for mounting MCBs (but without MCBs and incomer) as required. (Note : Vertical type MCB TPDB is normally used where 3 phase outlets are required.)

4 way (4 + 12), Double door

8 way (4 + 24), Double door

Supplying and fixing Cable End Box (Loose wire box)(IP 43) suitable for following single pole and neutral, sheet steel, MCB distribution board, 240 V, on surface/ recess, complete with testing and commissioning etc. as required.

For 6 way, Double door SPN MCBDB

For 8 way, Double door SPN MCBDB

Supplying and fixing Cable End Box (Loose wire box)(IP 43) suitable for following triple pole and neutral, sheet steel, MCB distribution board, 415 V, on surface/ recess, complete with testing and commissioning etc. as required.

For 4 way, Double door TPN MCBDB

For 6 way, Double door TPN MCBDB

For 8 way, Double door TPN MCBDB

Supplying and fixing Cable End Box (Loose wire box) suitable for triple pole and neutral, sheet steel, Vertical MCB distribution board, 415 V, on surface/ recess, complete with testing and commissioning etc. as required.

Supplying and fixing 5 amps to 32 amps rating, 240/415 volts, "C" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required.

Single pole

Double pole

Triple pole

Supplying and fixing single pole blanking plate in the existing MCB DB complete etc. as required.

Supplying and fixing following rating, double pole, 240 volts, isolator in the existing MCB DB complete with connections, testing and commissioning etc. as required. 40 Amps

Supplying and fixing following rating, four pole, 415 volts, isolator in the existing MCB DB complete with connections, testing and commissioning etc. as required.

Supplying and fixing following rating, double pole, (single phase and neutral), 240 volts, residual current circuit breaker (RCCB), having a sensitivity current upto 300 milliamperes in the existing MCB DB complete with connections, testing and commissioning etc. as required.

Supplying and fixing DP sheet steel enclosure on surface/ recess along with 25/32 A, 240 V “C” curve DP MCB complete with connections, testing and commissioning etc. as required.

Supplying and fixing 20 amps, 240 volts, SPN industrial type, socket outlet, with 2 pole and earth, metal enclosed plug top alongwith 20 amps "C" curve, SP, MCB, in sheet steel enclosure, on surface or in recess, with chained metal cover for the socket out let and complete with connections, testing and commissioning etc. as required.

Supply of recessed type LED downlighter with powder coated die-cast aluminium housing and LEDs of approved make pasted on diecast housing and high efficiency PMMA diffuser .Specially designed flat opal diffuser fixed to housing with engg. Plastic front cover, Driver installed on cast aluminium housing and prewired upto the terminal block. It has a system lumen of >1200 lumens with luminaire efficacy of not less than 100lm/W and lumen maintainence of 70% at the end of 50000 burning hours with constant current driver output, operating range 140V – 270V, 50Hz AC supply, CCT of 5700K - 6500K with PF>0.95 and THD must be <15% & surge proctection of > 2.5kv. The luminaire is IP 20 protected. LM 79 report to be submitted for luminaire and LM 80 for LED source. LED shall have reverse polarity, open and short circuit protection. ( similar to Bajaj CAT No. BZSLO 12W WH PRO or equivalent).

Supply of Surface/suspended Mounted LED luminaire having housing made from CRCA steel sheet, diffuser is supported by a pair of engg. plastic end plates which facilitate easy removal for maintenance. LEDs of Approved make with Constant current output driver with operating range 140 – 270V 50Hz AC supply voltages and system lumen of >3920 lm with luminaire efficiency of not less than 100 lm/w, THD must be <15% & Surge protection of >5kV. LED shall have reverse polarity, open and short circuit protection. ( similar to Bajaj CAT No. BICDP 40W LED IP20 or equivalent).

Supply of recessed 2'X2' LED luminaire CRCA steel sheet housing comprising of LED’s of approved make with Constant current output driver, It has a system level lumen of >3600 lumens with luminaire efficacy of not less than 100 lm/W. constant current output driver, operating range 140 – 270V AC supply, voltages, CCT of 5700K - 6500K with PF>0.95 and THD must be <15% & surge proctection of > 2.5kv. lumen maintainence of 70% at the end of 50000 burning hours. The luminaire is IP 20 protected. LM 79 report to be submitted for luminaire and LM 80 for LED source. LED shall have reverse polarity, open and short circuit protection. ( similar to Bajaj CAT No. BCTBLR 36W FP WH or equivalent).

Supply of recessed 2'X2' LED luminaire with dimmable ballast CRCA steel sheet housing comprising of LED’s of approved make with Constant current output driver, It has a system level lumen of >3600 lumens with luminaire efficacy of not less than 100 lm/W. constant current output driver, operating range 140 – 270V AC supply, voltages, CCT of 5700K - 6500K with PF>0.95 and THD must be <15% & surge proctection of > 2.5kv. lumen maintainence of 70% at the end of 50000 burning hours. The luminaire is IP 20 protected. LM 79 report to be submitted for luminaire and LM 80 for LED source. LED shall have reverse polarity, open and short circuit protection. ( similar to Bajaj CAT No. BCTBLR 36W FP WH dimmable or equivalent).

Supply of 6W Sleek surface mounted round LED downlighter luminaire. (Similar to Bajaj CAT No. BGSLO SLEEK SURFACE 6 WH RD or equivalent).

Supply of recessed mounted adjustable LED downlighter with powder coated pressure die-cast aluminium housing in COB LED die-cast aluminium carriage assembly .Lighting system comprising of LED of approved make & reflector. It has a system level lumen of 3132 lumens with luminaire efficacy of not less than 76 lm/W current output driver, operating range 140V – 270V, 50Hz AC supply, CCT of 5700K - 6500K with PF>0.95 and THD must be <15% & surge proctection of > 2.5kv. LED shall have reverse polarity, open and short circuit protection. ( similar to Bajaj CAT No. BRDCSL 16W WH or equivalent).

Supply of LED street light with epoxy powder coated (RAL 7024) high pressure die - cast aluminium housing with weather proof gasket for lamp and control gear, clear polycarbonate front cover fixed with SS screws, LED 's to be provided with individual lense optics to get optimum Optical performance, with IP-65, IK07 protection and CCT of 5700K-6500K and system lumen of 2500 lm, luminaire efficacy of not less than 100Lumen/ per watt, Power factor of > 0.95 and voltage range of 140- 270V, 50Hz AC, current THD < 15% & surge protection of > 5kV to be provided with a provision for side entry mounting for 38mm OD pipe bracket including double arm bracket. LED shall have reverse polarity, open and short circuit protection. ( similar to Bajaj cat Ref : BCLST 25W LED or equivalent).

Supply of LED street light with epoxy powder coated (RAL 7024) high pressure die - cast aluminium housing , weather proof gasket for lamp and control gear, clear polycarbonate front cover fixed with SS screws, LED 's to be provided with individual lense optics to get optimum potical performance, with IP-65, IK07 protection and a colour temperature CCT of 5700K-6500K and system lumen of >1125 lm, luminaire efficacy of not less than 75Lumen/ per watt. Power factor of > 0.95 and voltage range of 140- 270V, 50Hz AC, current THD < 15% & surge protection of > 5kV to be provided with a provision for side entry mounting for 38mm OD pipe bracket including single arm bracket. LED shall have reverse polarity, open and short circuit protection. ( similar to Bajaj cat Ref : BCLST 15W LED or equivalent).

Supply of LED Post top luminaire with housing in pressure die cast aluminium and powder coated aluminium reflector ,IP: 65 protection indirect light, wired with inbuilt constant current driver with CCT of 5700K-6500K and system lumen of >2700 lm, luminaire efficacy of not less than 60Lumen/ per watt. Power factor > 0.95 and voltage range of 140- 270V, 50Hz AC, THD < 15% & surge protection of > 5kV. LED shall have reverse polarity, high voltage, open and short circuit protection. ( similar to Bajaj Cat Ref: BRIL 45W LED NW or equivalent).

Supply of LED aviation light with Die-cast aluminum housing with Red polycarbonate dome for better illumination, Integral driver, IP:65, Features and Benefits Protection against short-circuit. Protection against surge. Wide operating input voltage range 100 – 270VAC, lumen maintainence of 70% at the end of 50000 burning hours. ( Similar to Bajaj CAT No. BGAV 302 LED or equivalent).

Supply of LED Bulkhead luminaire, Vandal resistant Polycarbonate diffuser with IP 65, IK08 dust tight and water Jet proof for clean operation, lumen maintainence of 70% at the end of 50000 burning hours, operating range 140 – 270V, 50Hz AC supply voltages and system lumen >650 lm, luminaire efficiency of luminaire not less than 65 lm/w ,THD <15% & Surge protection >2.5kV, CCT 5700K -6500K. LED shall have reverse polarity, open and short circuit protection. ( similar to Bajaj CAT No.BIBWP 10W LED or equivalent).

Supply of 1400mm dia sweep ceiling fan copper wound with blades white in color, ISI marked complete with capcitor, down rod, split pin, reel but without regulator complete as required.

Supply of 1200mm dia sweep ceiling fan copper wound with blades white in color, ISI marked and 5 star rated complete with capcitor, down rod, split pin , reel but without regulator complete as required.

Supply of 300mm dia sweep wall fan with Oscillating type complete with built in String type speed regulator and mounting arrangement.

Supply & transport to site of 3W LED Double sided Exit Signage Light with inbuilt 2 hours battery back up . (Similar to Bajaj BESL 03 LED DSD WBB (Green/Red) or equivalent).

Supply of 300 mm dia sweep metal body, 1400 RPM Exhaust fan with guard and mounting arrangement.

Supply of single phase 1400RPM, 450 mm dia sweep Heavy Exhaust fan.with Louver and shutter/Guard.

Supply of flexible LED light strip 15W per running meter strip in transparent unit with approx. 120Nos of LEDs per meter (IP:65) complete with driver complete as required. ( similar to Bajaj BCFL 300 75W IP65 OR EQ.)

Supply of rectangular flood LED light light with presssure die-cast aluminimum cover on both side for holding extruded aluminium heat sink, with heat resistant toughened glass with control gear, CCT 5700K-6500K, power factor >0.95, 140V-270V, 50Hz AC Voltage range, with surge protection >2.5kV, with open & short circuit protections. ( similar to Bajaj BARFEG 180W LED IP65 OR EQ.)

Supplying of 3.5 m long octagonal continuously tapered galvanised street light pole with single arm (bracket) of GI for installation of LED luminaire suitable for wind velocity of not less than 47m/sec fabricated out of 3mm MS plate, in single section, suitable to fix on pre-cast foundation with supply of 4 nos. of foundation bolt & anchor plate, rigid flange plate welded with the base of pole fixing on foundation bolts complete as required for structural stability as specified, wearther proof and vandal resistance door of height not less than 300mm flush with exterior surface containing a terminal plate of 4mm thick backlite sheet with 4 way, 63A epoxy connector & insulated caps for loop in loop out cable terminations suitable for upto three numbers 4 core 10,16sqmm cables & 10A DP MCB for each fixture connection, earthing bolts for continuous earth connections complete as required & as specified.

Supplying of 3.5 m long octagonal continuously tapered galvanised street light pole with provision to fix post top lantern for installation of LED luminaire suitable for wind velocity of not less than 47m/sec fabricated out of 3mm MS plate, in single section, suitable to fix on pre-cast foundation with supply of 4 nos. of foundation bolt & anchor plate, rigid flange plate welded with the base of pole fixing on foundation bolts complete as required for structural stability as specified, wearther proof and vandal resistance door of height not less than 300mm flush with exterior surface containing a terminal plate of 4mm thick backlite sheet with 4 way, 63A epoxy connector & insulated caps for loop in loop out cable terminations suitable for upto three numbers 4 core 10,16sqmm cables & 10A DP MCB for each fixture connection, earthing bolts for continuous earth connections complete as required & as specified.

Supplying,installation,testing and commissioning of Microwave technology based occupancy sensor having high preformance, non regulating programmable type, suitable for connected load upto 10Amp , for mounting height up to 2.6 mtr and for 5m X 20m coverage area along with necessary fixing arrangements i/c programming at site etc. complete as required.

Supplying,installation,testing and commissioning of storage type automatic electric water heater pressure type with Max pressure of 8Kg/cm2 at Max 80 mt head thermostatically controlled, suitable for operation on 230 volts 50 cycles, single phase, vertical wall mounting fitted with drawable and adjustable type A.C thermostat with thermostat knob to be readily accessable through the opening of suitable cover for adjustment of temperature in the installed position of heater and the thermostat should be with drawn without having to drain the water electric heating element of 2000 Watt made out of copper tube(heating element should be easily removed and replaced in the installed position of heater) a neon indicator with fusible plug, inner container made out of copper tinned both from inside and outside, outer container made out of mild steel sheet finished in gleaming white stove enamel paint and insulated between the inner and outer with fibre with glass wool /PUF insulation with 1 meter length of suitable capacity 3 core flexible cord with plug complete as required by the Engineer-in-Charge. 15 litre capacity water heater.

Installation, testing and commissioning of pre-wired, LED fitting with driver/ fluorescent fitting / compact fluorescent fitting of all types, complete with all accessories and tube/lamp etc. directly on ceiling/ wall/ surface, including connections with 1.5 sq. mm FRLS PVC insulated, copper conductor, single core cable and earthing etc. as required.

Installation, testing and commissioning of pre-wired, LED fitting with driver/ fluorescent fitting / compact fluorescent fitting of all types, complete with all accessories and tube/lamp etc. on false ceiling including connections with 1.5 sq. mm FRLS PVC insulated, copper conductor, single core cable and earthing etc. as required.

Installation, testing and commissioning of pre-wired, LED fittings with driver/ fluorescent fitting / compact fluorescent fitting of all types, complete with all accessories and tube etc., including supplying and fixing ball and socket arrangement, 2 Nos. down rods of 20 mm dia X 1.6 mm thick steel conduit upto 30 cm length, painting and wiring the down rods and connections with 1.5 sq. mm FRLS PVC insulated, copper conductor, single core cable and earthing etc. as required.

Installation, testing and commissioning of ceiling fan, including wiring the down rods of standard length (upto 30 cm) with 1.5 sq. mm FRLS PVC insulated, copper conductor, single core cable etc. as required.

Supplying and fixing extra down rod of 10 cm length G.I. pipe,15 mm dia, heavy gauge including painting etc. as required. (Note: More than 5 cm length shall be rounded to the nearest 10 cm and 5 cm or less shall be ignored)

Supplying and fixing extra conduit down rod of 20 cm length G.I. pipe 15 mm dia, heavy gauge including painting etc. as required. (Note : More than 5 cm length shall be rounded to the nearest 10 cm and 5 cm or less shall be ignored)

Numbering of ceiling fan/ exhaust fan/ fluorescent fittings as required.

Installation of 3.5 high octagonal street light pole with all accessories and supply & making foundation of reinforced cement concrete 1:3:6 (1 cement :3 coarse sand : 6 graded stone aggregate 40mm nominal size) including excavation and refilling, including positioning of template & foundations bolts (supplied with pole to match with pole base plate) complete as required and as specified.

Supplying and embedding following dia G.I. pipe (medium class) in pole collar/ foundation (during casting) for cable entry including bending the pipe to the required shape complete as required. 32 mm dia

Supply Installation, Testing & Commissioning of UL Certified Early Streamer Emission Lightning Conductor (ESELC) having Δt (gain in triggering time) of minimum 60 ųs and radius of protection 79 metres in Level 1 protection zone at 5 metre height with other accessories for installation of ESELC complete as required & as per enclosed specifications. Similar to :- Indelec, France Prevectron 3 Model S 60 or Approved Equivalent

Self-powered non resettable Lightning Event Counter (6 digit) mounted on down conductor in IP 67 enclosure with minimum sensitivity 1 kA for 8/20 µs pulse. ESE Lightning Strike Counter.

Supply, installation, testing and commissioning of Lightning Tester to Test the Lightning Arrester functionality etc. complete as required.

Supply & laying of 70 Sq.mm XLPE insulated PVC sheathed unarmoured copper conductor cable as down conductor from air terminal to the earth pits on surface/ in existing piping with all fixing accessories as required as per site conditions & as per enclosed specification.

Supply of Maintenance Free Earthing system including (i) Earth electrode of Copper bonded high tensile low carbon steel rods - 21mm dia,3 mtr long, having 250 microns copper bonding on MS Rod – 1 Nos. (ii) Earth Enhancing Compound in 50 Kg Bag - 1 Nos., etc. complete as required.

Installation & testing of maintenance free earthing Pit for Natural Soil as follows - (i) Digging / Auguring/ Boring of single earth pit of 100/150 mm dia to the depth of approximate 3 Mtr. (ii) Insertion of 3 Mtr. Electrode where the natural soil is assumed. (iii) Filling of earth pit with earth enhancement compound in slurry form and back filling. etc. complete as required.

Supply & installation of Earth Test Link box : Test Clamp to connect the down conductor to the earth termination and disconnect the down conductor from the earth termination for regular checks of the earth termination resistance value. The test clamp having the copper bus bar of 50 X 6 X 200 mm along with high grade insulator and copper bus bar having 8 hole of 12 mm dia with properly arranged in IP65 water resistant box.

Supply of following sizes of Power Cables, multi stranded conductor, XLPE Insulated, cores laid up, PVC tape / Extruded Inner sheathed , Un. Armour or Armour, FRLS at outer sheathed,1100V grade as per IS 7098(Part 1) 1988

2CORE 16 sq.mm. CU Ar. XLPE cable

4CORE 10 sq.mm. CU Ar. XLPE cable

4CORE 16 sq.mm. CU Ar. XLPE cable

4CORE 25 sq.mm. CU Ar. XLPE cable

Laying and fixing of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 kV grade of following size on cable tray as required. Upto 35 sq. mm (clamped with 1mm thick saddle)

Supplying and making end termination with brass compression gland and copper lugs for following size of PVC insulated and PVC sheathed / XLPE copper conductor cable of 1.1 KV grade as required.

4C X 10 sq. mm

4C X 16 sq. mm

2C X 16 sq. mm

4C X 25 sq. mm

Providing, laying and fixing following dia RCC hume pipe NP2 class (light duty) in ground complete with RCC collars, jointing with cement mortar 1:2 (1 cement : 2 fine sand) including trenching (75 cm deep) and refilling etc. as required.

100 mm dia

150 mm dia

Providing, laying and fixing following dia G.I. pipe (medium class) in ground complete with G.I. fittings including trenching (75 cm deep) and re-filling etc. as required

50 mm dia

80 mm dia

Supplying and laying 25 mm X 5 mm G.I strip at 0.50 metre below ground as strip earth electrode, including connection/ terminating with G.I. nut, bolt, spring, washer etc. as required. (Jointing shall be done by overlapping and with 2 sets of G.I. nut bolt & spring washer spaced at 50mm)

Earthing with G.I. earth plate 600 mm X 600 mm X 6 mm thick including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe of 2.7 metre long etc. with charcoal/ coke and salt as required.

Providing and fixing 25 mm X 5 mm G.I. strip in 40 mm dia G.I. pipe from earth electrode including connection with G.I. nut, bolt, spring, washer excavation and re-filling etc. as required.

Providing and laying earth connection from earth electrode with 6 SWG dia G.I. Wire in 15 mm dia G.I. pipe from earth electrode including connection with G.I. thimble excavation and re-filling as required.

Providing and fixing 25 mm X 5 mm G.I. strip on surface or in recess for connections etc. as required.

Providing and fixing 6 SWG dia G.I. wire on surface or in recess for loop earthing as required.

Supplying and installing following size of perforated painted with powder coating M.S. cable trays with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with M.S. suspenders including bolts & nuts, painting suspenders etc. as required.

150 mm width X 50 mm depth X 1.6 mm thickness

300 mm width X 50 mm depth X 1.6 mm thickness

450 mm width X 62.5 mm depth X 2.0 mm thickness

600 mm width X 62.5 mm depth X 2.0 mm thickness

750 mm width X 62.5 mm depth X 2.0 mm thickness

Supplying and installing following size of perforated painted with powder coating M.S. cable trays bends with perforation not more than 17.5%,, joined with connectors, suspended from the ceiling with M.S. suspenders including bolts & nuts, painting suspenders etc. as required.

150 mm width X 50 mm depth X 1.6 mm thickness

300 mm width X 50 mm depth X 1.6 mm thickness

450 mm width X 62.5 mm depth X 2.0 mm thickness

600 mm width X 62.5 mm depth X 2.0 mm thickness

750 mm width X 62.5 mm depth X 2.0 mm thickness

Supplying and installing following size of perforated painted with powder coating M.S. cable trays Tee with perforation not more than 17.5%, joined with connectors, suspended from the ceiling with M.S. suspenders including bolts & nuts, painting suspenders etc. as required.

150 mm width X 50 mm depth X 1.6 mm thickness

300 mm width X 50 mm depth X 1.6 mm thickness

450 mm width X 62.5 mm depth X 2.0 mm thickness

600 mm width X 62.5 mm depth X 2.0 mm thickness

750 mm width X 62.5 mm depth X 2.0 mm thickness

Supplying and installing following size of perforated painted with powder coating M.S. cable trays Cross Member with perforation not more than 17.5%, joined with connectors, suspended from the ceiling with M.S. suspenders including bolts & nuts, painting suspenders etc. as required.

150 mm width X 50 mm depth X 1.6 mm thickness

300 mm width X 50 mm depth X 1.6 mm thickness

450 mm width X 62.5 mm depth X 2.0 mm thickness

600 mm width X 62.5 mm depth X 2.0 mm thickness

Supplying and installing following size of perforated painted with powder coating M.S. cable trays Reducer with perforation not more than 17.5%, joined with connectors, suspended from the ceiling with M.S. suspenders including bolts & nuts, painting suspenders etc. as required.

150 mm width X 50 mm depth X 1.6 mm thickness

300 mm width X 50 mm depth X 1.6 mm thickness

450 mm width X 62.5 mm depth X 2.0 mm thickness

600 mm width X 62.5 mm depth X 2.0 mm thickness

Supply & Fixing of factory fabricated pre-galvanized G.I. sheet steel raceway in 1.6mm thickness for bottom & sides and 2/3mm thick top Cover including juction boxes with 3mm cover plate and as called for including necessary civil work such as chase cutting in screed, fixing/ jamming the raceway, aligning & levelling and finishing with sand cement plaster & chicken wire mesh:

100mm x 40mm (2mm top Cover)

150mm x 40mm (2mm top Cover)

250mm x 40mm (3mm top Cover)

Supply, installation, testing and commissioning of 1kVA, 1 Phase input and 1Phase output UPS alongwith lead acid batteries giving a back up of min. 30min. at full load as per specification alongwith all accessories including interconnecting cables, lugs, Base Frames, Battery Rack & Battery Circuit breaker complete as required.

Supply, installation, testing and commissioning of 2kVA, 1 Phase input and 1Phase output UPS alongwith lead acid batteries giving a back up of min. 30min. at full load as per specification alongwith all accessories including interconnecting cables, lugs, Base Frames, Battery Rack & Battery Circuit breaker complete as required.

Supply, Instalaltion, testing & commissioning of Variable Refrigerant Flow modular type airconditioning system with stepless modulation complete with indoor and outdoor units, individual remote controller & centralized controller, interconnected refrigerant piping , full charge of refrigerantgas & oil, control cabling etc. as per detail given in specifications & having following items:(Refrigerant to be used shall be R - 410 A ). Supply Instalaltion, testing & commissioning of Modular type outdoor units ( COP 3.7 at AHRI condition ) equipped with highly efficient scroll compressors with all inverter type compressor (s) , special heat exchanger, low noise condenser fan , auto check function for connection error, auto address setting and capacity as mentioned below.

32 HP Heating & Cooling

36 HP Heating & Cooling

42 HP Heating & Cooling

44 HP Heating & Cooling

48 HP Heating & Cooling

52 HP Heating & Cooling

58 HP Heating & Cooling

Supply Instalaltion, testing & commissioning of Indoor units address setting and capacity as mentioned below. multispeed motor, coil section with DX coil, outer cabinet, drain pan, drain water lift-up mechanism insulation, pipe connections, fresh air intake etc. of various capacities as per specifications and drawings

1.6 TR (Minimum) (Ceiling Mounted Cassette Type)

2.0 TR (Minimum) (Ceiling Mounted Cassette Type)

2.5 TR (Minimum) (Ceiling Mounted Cassette Type)

3.2 TR (Minimum) (Ceiling Mounted Cassette Type)

4 TR (Minimum) (Ceiling Mounted Cassette Type)

Panel for Cassette units

Supply Instalaltion, testing & commissioning of Indoor units address setting and capacity as mentioned below. multispeed motor, coil section with DX coil, outer cabinet, drain pan, drain water lift-up mechanism insulation, pipe connections, fresh air intake etc. of various capacities as per specifications and drawings

6.4 TR (Minimum) (ceiling mounted duct type)

8.0 TR (Minimum) (ceiling mounted duct type)

1.0 TR (Minimum) with cordless remote (Hi-wall type)

1.28 TR (Minimum) with cordless remote (Hi-wall type)

1.6 TR (Minimum) with cordless remote (Hi-wall type)

2.0 TR (Minimum) with cordless remote (Hi-wall type)

Supply Instalaltion, testing & commissioning of HRV Unit of following capacity:. 380 CFM

Supply Instalaltion, testing & commissioning of Y-joints.

Supply testing & commissioning of self diagnostic type remote controllers for ductables and cassettes . Corded Type

Supply Instalaltion, testing & commissioning of Main Intelligent touch screen central controller system including all the accessories suitable to operate, monitor, on/off, temperature setting of all the indoor units indiviually complete as required and as specified.

Supply & Fixing of Interconnecting copper refrigerant pipe work of following sizes insulated with (class O) 25 mm / 19 mm thick Elastomeric Nitrile Rubber between indoor and outdoor units i/c refrigrant as per specifications. Pipes ahall be fixed with suitable size of clamp / MS hanger / MS support / MS angle as per site requirement.

41.3 mm O.D. Pipe Size with insulation of 25 mm thick

34.9 mm O.D. Pipe Size with insulation of 25 mm thick

28.58 mm O.D. Pipe Size with insulation of 25 mm thick

22.2 mm O.D. Pipe Size with insulation of 25 mm thick

19.05 mm O.D. Pipe Size with insulation of 25 mm thick

15.88 mm O.D. Pipe Size with insulation of 19 mm thick

12.7 mm O.D. Pipe Size with insulation of 19 mm thick

9.5 mm O.D. Pipe Size with insulation of 19 mm thick

6.4 mm O.D. Pipe Size with insulation of 19 mm thick

Supply and fixing of UPVC SCH 80 (10Kg/ cm sq) drain water piping complete with fittings, support as per specification and insulated with 09 mm thick insulated with Nitrile Rubber insulation.

25 mm dia

32 mm dia

40 mm dia

Supply, installation, balancing and commissioning of factory fabricated GSS sheet metal rectangular/round ducting complete with neoprene rubber gaskets, elbows, splitter dampers, vanes, hangers, supports etc. as per approved drawings and specifications of following sheet thickness complete as required.

Thickness 0.63 mm sheet

Thickness 0.80 mm sheet

Thickness1.00 mm sheet

Thickness 1.25 mm sheet

Supplying, fixing testing commissioning of supply air diffusers of powder coated aluminium with aluminium volume control dampers with anti smudge ring & removable core.

Supplying, fixing testing commissioning of Return air diffusers of powder coated aluminium without volume control dampers with anti smudge ring & removable core.

Supplying & fixing of Fresh air intake louvers with bird screen dampers (Aluminium extruded only).

Supplying and fixing of acoustic lining of duct with Open Cell Nitrile Rubber density 140-180 Kg/m³. Applied by Adhesive, conforming to standard specification. 10 mm thick open cell nitrile rubber.

Supplying and fixing of following thickness duly laminated aluminium foil of mat finish closed cell Nitrile Rubber (Class 'O' ) insulation on existing duct after applying suitable adhesive for Nitrile rubber. The joints shall be sealed with 50 mm wide and 3 mm thick self adhesive nitrile rubber tape insulation complete as per specifications as required. 9 mm thick

Supply, installation, testing ans commissioning of Motorized ( ON - OFF Type) duct mounted GI volume control damper with enthalpy sensor and necessary control wire ( minimum 1.5 sq. mm ) for integration within AHU room.

Damper

Actuator

Supply, laying, testing and commissioning of Split Unit (BEE Five Star Rated ) including power and control cabling , outdoor stand as per Standard specification including as required.

1.5 TR Capacity - Hi wall

2.0 TR Capacity - Hi wall

Supply installation, testing and commissioning of Inline Fan directly coupled TEFC Sq.cage induction motor (F-class insulation & B-class Temp. rise) suitable for 415V±10%, 50 Hz. 3 phase electric supply complete with Bird Screen Al gravity louvers, Fan frama, cable, required hardware etc. as required.

Toilet Exhaust Inline Ventilation fan Air Qty. = 500 CFM Static Pressure = 15mm Wg Fan Speed = not exceeding 700 rpm Motor = 0.5 KW Fan Dia = 400 mm (Approx.) Noise level = not exceed 90 db at 1 meter distance

Toilet Exhaust Inline Ventilation fan Air Qty. = 700 CFM Static Pressure = 15mm Wg Fan Speed = not exceeding 700 rpm Motor = 0.5 KW Fan Dia = 400 mm (Approx.) Noise level = not exceed 90 db at 1 meter distance

Supply installation, testing and commissioning of Propellar Fans, insulation class B, IP class 44, 1500 RPM suitable for 230V±10%, 50 Hz. 1 phase, electric supply complete with cable, required hardware etc. as required. Fan Type = Propellar Fan Fan Dia. = 300 mm

Supply, Installation, Testing & Commissioning of Networkable Microprocessor based following loops intellegent analog Addressable Type Fire Alarm Control Panel, with minimum 168 character LCD display,The panel should be equiped with loop capacity to take minimum 125+125 intellegent addressable detectors/ devices in one loop. Four access levels, capable of taking Protocol Devices, Graphical Display, sufficient numbers of programmable relay controls for controlling pressurization fans, ventilation fans, fire pump room, monitoring of fire sprinkler and fire hydrant pump, 240 volts, 50 Hz AC power supply, automatic battery charger, 24 volts sealed maintenance free lead acid batteries sufficient for 24 hours normal working and then be capable of operating the system for 2 hours during an emergency conditions as required. The panel shall be UL/EN listed and shall be hooked up with PA system.It shall have interfacing connectivity (BACNET/ MODBUS/ Openprotocol gateway) for Building Management System complete as required. Autodialler shall also be provided. Panel to panel networking shall be Master-Slave configuration (6 loop panel shall be Master Panel).

6 loop panel

2 Loop Panel

Supply, Installation, Testing & commissioning of UL/EN listed (latest version) intelligent addressable multicriteria detector {Smoke + heat (fixed and rate of rise) } with unique optical sensing chamber, visible LED, fully coated circuit board, superior RF / Transient protection suitable for 2 wires loop connection, complete with plug into common separate base & housing constructed of LEXAN (or polycarbonate) complete with connections etc. as required and as per enclosed specifications. (Cost of plug in common base shall deemed to be included in cost of detectors)

Supply, Installation, Testing & commissioning of UL/EN listed (latest version) intelligent addressable Manual Pull station (not break glass type) suitable for semi flush mounting with double gang outlet box, equipment for key operated test-reset lock, electronic or rotary switches for address setting. Manual pull station shall be connected with two wire to SLC loop of Fire Control Panel. Cover shall be made out of LEXAN (or poly carbonate equivalent) with clear operating instruction and the word Fire appearing on the front complete with connections etc. as required and as per enclosed specifications.

Supply, installation, testing and commissioning of UL/EN listed (latest version) Intelligent addressable control module/ relay module (output module) for tripping of AHU & Ventilation / pressurisation fans / hooter complete with termination etc. as required and as per enclosed specification.

Supply, installation, testing and commissioning of UL/EN listed (latest version) Intelligent addressable monitor module for connecting flow switch, pressure switch and other external system with fire alarm system complete with termination etc. as required and as per enclosed specification.

Supply, installation, testing and commissioning of UL/EN listed (latest version) fault isolator module including termination etc. as required and as per enclosed specification.

Supply, installation, testing and commissioning of UL/EN listed (latest version) Wall Mounted Hooter-cum- strobe with minimum 90dB output at a distance of 1 mtr. and with required power supply converter (230VAC to 12/24 VDC) complete with termination etc. as required and as per enclosed specification.

Supply, installation, testing and commissioning of UL/EN listed (latest version) Response Indicator (LED in polycorbonate housing) complete with termination etc. as required and as per enclosed specification.

Supply of FRLS XLPE insulated PVC sheathed, stranded copper conductor armoured cable 1100 V grade as per IS 7098(part 1)1988, amended upto date as required. 2 x 1.5sqmm

Laying and fixing of one number PVC insualted and PVC sheathed / XLPE aluminium/ copper conductor cable of 1.1 KV grade of size not exceeding 35 sq.mm on cable tray as required.

Laying and fixing of one number PVC insualted and PVC sheathed / XLPE aluminium/ copper conductor cable of 1.1 KV grade of size not exceeding 35 sq.mm on surface as required.

Laying of one number PVC insualted and PVC sheathed / XLPE aluminium/ copper conductor cable of 1.1 KV grade of size not exceeding 35 sq.mm on direct in ground, including excavation, sand cushioning, protective covering and refilling the trench etc. as required.

Supplying and installing following size of perforated pre-painted M.S cable trays with perforation not more than 17.5% in convenient sections,joined with connectors,suspended from the ceiling with M.S suspenders including bolts & nuts,painting suspenders etc as required. 100 mm width x 50 mm depth x 1.6 mm thickness

Supplying and installing following size of perforated pre-painted M.S cable trays bends with perforation not more than 17.5% ,joined with connectors,suspended from the ceiling with M.S suspenders including bolts & nuts,painting suspenders etc as requuired. 100 mm width x 50 mm depth x 1.6 mm thickness

Supplying and installing following size of perforated pre-painted M.S cable trays Tee's with perforation not more than 17.5% ,joined with connectors,suspended from the ceiling with M.S suspenders including bolts & nuts,painting suspenders etc as required. 100 mm width x 50 mm depth x 1.6 mm thickness

Supplying and installing following size of perforated pre-painted M.S cable trays cross members with perforation not more than 17.5% ,joined with connectors,suspended from the ceiling with M.S suspenders including bolts & nuts,painting suspenders etc as required. 100 mm width x 50 mm depth x 1.6 mm thickness

FIRE HYDRANT Supplying & fixing Internal and External stainless steel single headed fire hydrant landing valve of 63mm dia with cast iron wheel ISI marked conforming to IS:5290(Type-A) with blank PVC cap and chain as required.

Providing & fixing 63 mm dia STAINLESS STEEL short Branch pipe with 20mm (nominal internal diameter) in size stainless steel nozzle conforming to IS:903 suitable for instantaneous connection complete to inter-connect hose pipe, coupling etc. as required and as per enclosed specification.

Providing & fixing of MS Hose cabinet outdoor type of size 0.90 Mx 0.60 Mx 0.50 M made of 2mm thick MS sheet with 6mm thick glazed glass doors i/c necessary locking arrangement suitable to accomodate 2nos 15m long hoses, one no branch pipe, etc. and mounted on wall or with raised brick platform. The cabinet shall be painted with red colour shade No. 536 of IS: 5 externally & white internally complete in all respects for external hydrant and as per enclosed specification.

Providing & fixing 63mm dia., 15mtr. long RRL hose pipe (ISI Marked) with 63mm dia. male and female STAINLESS STEEL couplings duly binded with GI wire, rivets etc. conforming to IS- 636 (Type-A) complete as required & as per enclosed specification.

Providing and fixing First-Aid Hose Reel 20mm dia. x 30m long (minimum length) (Thermoplastic Type as per I.S. 12585) complete with drum, bracket, 25mm dia. shut-off valve and 5mm Gun-Metal nozzle conforming to IS-:884, connection with riser with MS C- class pipe, painting the MS works complete as required & as per enclosed specification.

Providing and fixing angle iron (40mmx40mmx5mm) door frame and S.S. sheet (2mm thick) cum glass shutter of size 2.1mtrx0.9mtr(N.S.) with 25mmx25mmx3mm angle frame all around and stiffened in between i/c hinges, handle, locking arrangement, painting with approved synthetic enamel paint i/c sign writing on glass at internal hydrant including providing & fixing S.S. sheet 2mm thick on remaining portion above door to close opening i/c painting etc. as required. Glass shall be 6 mm thick.

Providing and fixing 4 way Gun-metal Fire Brigade inlet connection comprising of 4 nos. 63mm dia. male instantaneous inlet couplings with cap and chain as required for 150mm dia. flanged conforming to IS- 904 complete (to be connected to static tank) as required and as per enclosed specification.

Providing and fixing fire brigade suction hose coupling (draw out connection) with nut for female coupling as per IS-902 complete with 150mm dia. Suction pipe and foot valve (to be connected to static tank) complete as required and as per enclosed specification.

Supplying and fixing orifice plate made of 6 mm. thick stainless steel with orifice of 80 mm dia in between flange & landing valve of external and internal hydrant to reduce pressure to working pressure of 3.5 kg/cm2 complete as required & as per enclosed specification. 80 mm dia.

Providing, fixing and jointing and commissioning including testing C- class heavy duty mild steel pipes conforming to IS-1239 upto 150mm dia.including cutting, welding, fittings viz bends, tees, reducers, flanges, nut-bolts, gasket complete and laying in ground including excavation, providing PCC block support at interval and giving suitable treatment for corrosion by way of min. 4mm thick corrosion protection tape which shall be wrapped comprising of coal tar/ asphalt component supported on fabric of organic/ inorganic fibre as per IS-10221, re-filling the trench etc.as required and as per enclosed specification.

150 mm dia.

100 mm dia.

Providing, fixing, jointing and commissioning of following sizes of C- class heavy duty Mild Steel pipes conforming to IS-3589, including cutting, welding, nut-bolts, gasket, fitting viz. bends, tees, reducers, crosses, flanges etc. and fixing the pipes on wall / ceiling / beam / floor with suitable MS clamps / structural supports/PCC block and painting complete as required and as per enclosed specification. Note: All sprinkler system fittings less than 50mm size shall be threaded and not welded.

200 mm dia. , 6 mm wall thickness

150 mm dia.

Providing, fixing, jointing and commissioning of following sizes of C- class heavy duty Mild Steel pipes conforming to IS-1239 upto 150mm dia., including cutting, welding, nut-bolts, gasket, fitting viz. bends, tees, reducers, crosses, flanges etc. and fixing the pipes on wall / ceiling / beam / floor with suitable MS clamps / structural supports/PCC block and painting complete as required and as per enclosed specification.

100 mm dia.

80 mm dia.

65 mm dia.

50 mm dia.

40 mm dia.

25 mm dia.

Providing & fixing butterfly valve of rating PN 1.6, wafer type, in cast iron body with Ductile Iron disc, EPDM seal, SS single piece shaft, conforming to IS-13095 of the following sizes complete with cast iron hand lever companion flanges, bolts, nuts, washers & inserted rubber gaskets, as required and as per enclosed specification.

150 mm dia.

50mm dia.

Providing & fixing CI non return valve conforming to API-594 with C.I. body, SS Disc, SS stem, EPDM seal, complete with companion flanges, bolts, nuts, washers & inserted rubber gasket complete as required and as per enclosed specification.

150 mm dia.

65 mm dia.

Providing & fixing of CI double flange sluice valve of rating PN 1.6 with non rising SS spindle, Bronze/Gun Metal seat confirming to IS -780 complete with flanges,nut-bolts, gasket, washers etc. as required and as per enclosed specification.

200mm dia.

150mm dia.

100 mm dia.

80 mm dia.

65 mm dia.

Providing & fixing of Stainless Steel double flange suction " Y" type strainer fabricated out of minimum 1.2 mm thick Stainless Steel sheet with 3 mm dia. perforation holes including nuts, bolts and 3 mm thick rubber insertion complete & tested to 10 Kg/Sq.cm pressure complete as required and as per enclosed specification.

150 mm dia.

80 mm dia.

Providing & fixing of 25mm dia. gunmetal air release valve with all fittings and forged ball valve on header complete as required and as per enclosed specification.

Providing and fixing following size Pressure gauge (0-15 Kg/Cm2) complete with shut off valve duly calibrated before installation complete as required & as per enclosed specification. 150mm dia.

Providing & fixing of installation control valve (Sprinkler Alarm Valve) of Cast iron body and bronze working parts comprising of water motor alarm, bronze seat clapper and clapper arm, hydraulically driven mechanical gong bell to sound continuous alarm when the Wet riser/Sprinkler system activates, pressure gauges, emergency releases ,strainer, pressure switch, cock valve complete with drain valve and bypass, test control box,ball valves, flanges, orifice plate, fittings, gasket etc.suitable for 150 mm diameter pipe size complete as required as per enclosed specification.

Providing and fixing water flow switches with threaded connection for indicating water flow in sprinkler branch line suitable for vertical/horizontal mounting as per site requirement complete as required and as per enclosed specification in following pipe sizes: (For 50 to 150 mm dia. Pipe sizes)

Providing and fixing double flanged vertical air vessel fabricated from 10mm M.S. plate with dished ends from 10mm M.S. plate, outside with one coat of primer and two coats of synthetic enamel paint of approved shade, complete with approved quality of pressure switches (04 Nos.), pressure gauges and all other required accessories to operate commonly main fire pump, sprinkler pump, Diesel Fire pumps and Jockey pumps at drop of pressure automatically at required pressure setting complete as required and as per enclosed specification. Recommended dia. : 450mm, Height of shell : 2000mm Working pressure :12 Kg/Sq.cm, Test Pressure : 25 Kg/Sq.cm

Providing and fixing reinforced neoprene rubber vibration eliminators/expansion joints (to provide relief from stresses at pipe flanges) suitable for upto 20 kg/cm2 pressure, as per specification of the manufacturers complete as required and as per enclosed specification.

150mm dia.

80mm dia.

65mm dia.

Providing & fixing of 15 mm dia. sprinkler head with standard response Quartzoid Bulb operate at 68 degree C complete with all accessories as required and as per enclosed specification (UL Listed) Upright type in chrome finish (Standard Coverage)

Providing & fixing of 15 mm dia. sprinkler head with standard response Quartzoid Bulb operate at 68 degree C complete with all accessories as required and as per enclosed specification (UL Listed). Concealed Type with base plate in powder coat finish of approved shade as specified (Standard Coverage)

Providing & fixing flexible tubes in corrugated SS, for connecting pendant sprinklers to branch lines complete with all necessary accessories, reducers, O-rings, nipples etc., supporting structural arrangments in the false ceiling/slab as per site requirement for the below lengths and tested for min 15 Kg/Sq.cm pressure with G.I. retainer rings & guide bolts complete as required and as per enclosed specification (UL Listed) For 1000 mm length

Supply of ISI marked portable type fire extinguishers of following type and capacity complete as per enclosed specification and fix / install as per site condition :

Co2 type 4.5 kg capacity as per IS- 15683

Stored Pressure ABC Powder (MAP Base), of 6kg : IS- 15683

Providing and fixing Mechanical Foam type (AFFF media) 50 Liters Capacity cylindrical shape fire extinguisher with gas cartridge, hose and all required accessories, complete as per IS-13386 - trolley mounted type for portable use.

SITC of electric driven main fire Hydrant & Sprinkler pumps suitable for automatic operation complete in all respect as required & as per enclosed specification and consisting of the following: Horizontal type multistage, centrifugal, split casing pump of cast iron body and bronze impeller with stainless steel shaft, to ensure minimum pressure of 3.5 kg/cm2 at highest and farthest outlet at specified flow of 2850 LPM & 88 m head conforming to IS- 1520 complete with mechanical seals, safety relief valve, pressure gauges on delivery side, drain and bypass arrangement for testing of pump complete. Suitable HP Squirrel cage Induction motor suitable for operation on 415V, 3 phase, 50Hz, AC supply for the above pump rating with synchronous speed of 1500 RPM, TEFC type confirming to IS-325 with IP:55 protection for enclosure, horizontal foot mounted with class F insulation, flexible coupling & coupling guard with the pump complete. Common bed plate fabricated from MS channel / ISMB with spring type vibration isolators. The pump set base shall be held by bolts grouted in the suitable cement concrete foundation duly plastered including foundation bolts, washers complete.

SITC of Diesel engine driven standby fire pump suitable for automatic operation complete in all respect as required & as per enclosed specification and consisting of the following: Horizontal type multistage, centrifugal, split casing pump of cast iron body and bronze impeller with SS shaft, to ensure minimum pressure of 3.5 Kg/Sqcm at the highest and farthest outlet at a flow 2850 LPM & 88 m head confirming to IS-1520 with mechanical seals, safety relief valve, pressure gauges on delivery and suction side, drain and bypass arrangement for testing of pump complete. Radiator Water cooled diesel engine developing required BHP at 1500 RPM for the pump, flexible coupling & coupling guard with the pump & common bed plate for mounting of engine & pump shall confirming to relevant BS/IS standard with auto starting mehanism. The common base frame shall be held by bolts grouted in the concrete including foundation bolts, washers as required, vibration damping arrangement by cushy foot & engine panel with battery charger provided by engine manufacturer, connection to engine starting panel, lead acid SMF batteries of 12V/24V, 180AH with casing, lugs, stand & terminations to diesel engine, charger complete. Exhaust pipe of required length ( discharge to leave above roof level as per standard) with 50mm thick glasswool pipe section, covered with aluminum cladding, residential silencer muffler, instruments & protection-stop solenoid for auto stop in the event of fault with auto indications, day oil tank of 200 ltrs.with first charge of diesel fabricated out of 4mm MS sheet with inlet/ outlet ON/OFF valves, level indicator, drain pipe, 15mm dia MS fuel line complete . Common bed plate of fabricated MS channel / ISMB with vibration isolator. The base frame shall be held by bolts grouted in the suitable cement concrete foundation duly plastered including foundation bolts, washers as required.

SITC of electric driven Pressurization/Jockey Pump suitable for automatic opertation complete as required & as as per enclosed specification and consisting of the following:Horizontal type end suction centrifugal,Jockey pump of cast iron body and bronze impeller, with SS shaft, to ensure at highest and farthest outlet at a flow of 180 LPM & 88 m head confirming to IS-1520 complete with necessary safety relief valve, drain, pressure gauge on the delivery and suction side including bypass arrangement for testing of the working of the pumping set as required. Suitable HP Squirrel cage induction motor suitable for operation on 415 V, 3 phase,50Hz, AC supply for the above pump with synchronous speed of 2900 RPM T.E.F.C. type confirming to IS - 325 with IP:55 protection for enclosure, horizontal foot mounted, class-F insulation, flexible coupling & coupling guard with the pump complete. Common base frame shall be fabricated from MS channel / ISMB with vibration isolator. The base frame shall be held by bolts grouted in the suitable cement concrete foundation duly plastered including foundation bolts, washers complete.

Supply, installation, testing and commissioning of the fire pump control panel, front operated cubicle construction, Floor mounted type, fabricated out of 2mm thick CRCA Sheet, Compartmentalized with hinged lockable doors, dust and vermin proof, Powder coated of approved shade after 7 tank treatment, Cable alley, inter-connections, having Switch gear and accessories mounting, internal wiring, earth terminals, Top/ Bottom cable entry, numberings etc. suitable for operation of 415 volts, 3 phase 4 wire 50 Hz AC Supply with enclosure protection class IP 42 complete as required and as as per enclosed specification with the following: ( details as per tender document)

Supply of following sizes of 1.1KV grade FRLS XLPE insulated and PVC sheathed aluminium conductor armoured stranded power cables conforming to IS 7098 Part-1 as ammended upto date and as per enclosed specification.

3 Core x 120 Sq. mm.

3 Core x 16 Sq. mm.

Supplying and making of cable end termination with brass single compression gland and Al. lug for following size of PVC insulated and sheathed armoured cables of 1.1 K.V. aluminum conductor as required

3 Core x 120 Sq. mm.

3 Core x 16 Sq. mm.

Providing and Fixing 25 mm x 5 mm G.I. Strip in 40 mm dia G.I. Pipe from earth electrode including connection with GI nut, bolt, spring, washer, excavation and refilling etc. as required.

Providing and Fixing 25 mm x 5 mm G.I. Strip on surface or in recess for earth connection as required.

Earthing with G.I. earth pipe 4.5 meter long, 40 mm dia including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe etc. with charcoal/coke and salt as required.

Supply installation testing and Commissioning of NOVEC 1230 Fire Suppression System with following items complete as required.

100L Seamless Cylinder with valve assembly, Supervisory pressure gauge. Super pressurised with Nitrogen at 42 bar.

Electrical actuator.

Novec 1230 Gas

Local Manual actuator.

Actuation hose for pneumatic connection. (Pilot Hose)

Disharge Hose.

Cylinder mounting clamps.

Nozzle Brass-360 / 180 Degree.

Supply and fixing of Piping- M.S. Seamless Sch.40 ASTM A-106 Gr. B with necessary fittings & accessories for following volume -

8.6X6.5X4.0 Meter (+5%) i/c Falce ceiling

4.5X4.4X4.0 Meter (+5%) i/c Falce ceiling

4.5X4.3X4.0 Meter (+5%) i/c Falce ceiling

16 sqmtr X 4 M (+5%) i/c Falce ceiling and false flooring

122.0 sqmtr X 4 M (+5%) i/c Falce ceiling and false flooring

Supply and fixing of warning Plate for use outside room.

Supply and fixing of warning Plate for use inside room.

Supply, installation, testing and commissioning of area Gas release Panel Suitable to connect with fire addassable Panel etc. complete as required.

Supply, installation, testing and commissioning of manual release Switch.

Supply, installation, testing and commissioning of abort switch.

SAKET INFRADEVELOPES PVT. LTD.

SGB INFRA LTD