REPAIR/REPLACEMENT OF LT SWITCH GEAR AND ALLIED WKS AT ELECTRICAL SUB STATION AND MAINTENANCE OF MT VEHICLES AND T AND P UNDER AGE(I) DHANA AT MIL STN DHANA.

Amount

Excavation in trenches in any type soil not exceeding 1.5 m wide and not exceeding 1.5 m in depth (for cable, pole, stay etc) and getting out complete all as specified and directed.

Returning filling in including spreading, leveling, watering and well ramming in layer not exc 25 cm complete all as specified and directed.

Removing excavated material not exc 50 mtr and depositing where directed at a level not exc. 1.5 m above the starting point complete all as specified and directed.

Material & Labour for providing dry river sand as in sand in trenches, ducts, transformer yard etc for cable cushioning complete all as specified and as directed. Note :- Depth after punning shall be measured and paid.

Taking out sub class burnt bricks from the trenches and stacking at site serviceable /unserviceable bricks for reuse complete all as specified and directed.

Supply and laying sub class old 'B' burnt bricks, size of brick 230x115x75mm, laid as cable protection cover complete all as specified and directed.

Supply & Fix in repair MCCB 4 pole 50 KA 400 A suitable for Adjustable type setting complete including replacement of existing U/S switchgear complete after disconnecting the incoming and outgoing cables making necessary modification to fix MCCB as outgoing including connections from bus bars to MCCBs with suitable bus bars of aluminium section duly bend/drilled reconnecting the removed cable etc and making provision to operate the MCCB from outside the door and necessary repairs to the door etc complete all as specified and directed.

All same as item No.7 above but for MCCB 4 pole 36 KA 250 A suitable for Adjustable type TM Range setting complete all as specified and directed.

All same as item No.7 above but for MCCB 4 pole 36 KA 200 A suitable for Adjustable type setting complete all as specified and directed.

All same as item No.7 above but for MCCB 4 pole 25 KA 160 A suitable for Adjustable type setting complete all as specified and directed.

All same as item No.7 above but for MCCB 4 pole 25 KA 125 A suitable for Adjustable type setting complete all as specified and directed.

All same as item No.7 above but for MCCB 4 pole 25 KA 63/100 A suitable for Adjustable type setting complete all as specified and directed.

Supply & Fix in replacement MCB SP, 240 volt, 6 to 32 Amps, complete all as specified and directed.

Supply & Fix in replacement MCB TPN, 415 volt, up to 63 Amps complete all as specified and directed.

Supply and fix in repair digital volt meter range up to 500 Volt, complete all as specified and directed.

Supply and fix in repair digital Amp meter range up to 300 Amp, complete all as specified and directed.

Supply and fix in repair led lamp indicator RYB complete all as specified and directed.

Removing the existing burnt out UG cable termination of 3.5 core 185 Sqmm to 240 Sqmm cable, cutting and removing the burnt out portion and preparing the cable termination and connecting up the cable after crimping 4 Nos of suitable aluminium lugs etc complete all as specified and directed.

All as per item No.18 above but for cable of 3.5 core 70 Sqmm to 150 Sqmm.

All as per item No.18 above but for cable of 3.5 core 35 Sqmm to 70 Sqmm.

All as per item No.18 above but for cable of 4 core 16 Sqmm to 25 Sqmm.

Dismantling the existing unserviceable cable gland, M & L for fixing new cable gland brass chromium plated suitable for the following sizes of cables. (a) 3.5 core 240/185 Sqmm

(b) 3.5 core 120/95 Sqmm

(c) 3.5 core 70/50 Sqmm

(d) 3.5/4 core 35/25/16 Sqmm

Supply and fix anti climbing device spikes type fabricated out of MS bars round / square and flat including nuts bolts washers and welding into two halves made to shape to suit to the cross section of the pole after removing the U/S, complete all as specified and directed.

Supplying, fabricating & fixing in repair, structural mild steel channel, angle, iron, flat iron and brackets etc for fabrications of cross arms, bracings, supports, D-clamps, stiffeners, eye hooks, bolts, pole clamps and back plates including nuts, bolts and washers, welding banding cold , or hot drilling holes for insulators bolts in any shape or size as indicated or directed and inclusive of one red oxide primer coat, one under coat and one finishing coat of aluminium paint complete all as specified and directed.

Repairs to the existing earthing complete by replacing the US G.I strip bolt, nut check nut and washer, earthing test point all as specified including testing on completion including making PCC chambers, RCC cover, GI funnel for watering, GI funnel, earth strip protection pipe, including 10 kgs of salt and watering, testing of earth result by megger and submitting the report. etc all as specified and as directed including writing and painting of earthing details Note:- (i) Required excavation and all materials, demolition etc is inclusive, (ii). Required earth strip and protection pipe will be measured and paid separately

Supply & Fix in repair GI strip 32 x 6 mm as earth continuity conductor or main earthing lead buried in ground or drawn through pipes or fixed to wall or poles or any other situation for loop earthing after removing the U/S etc as required complete all as specified and directed.

Supply & Fix in repair GI strip 25 x 4 mm as earth continuity conductor or main earthing lead buried in ground or drawn through pipes or fixed to wall or poles or any other situation for loop earthing etc after removing the U/S as required complete all as specified and directed.

Supply & Fix in repair GI strip 25 x 3 mm as earth continuity conductor or main earthing lead buried in ground or drawn through pipes or fixed to wall or poles or any other situation for loop earthing etc after removing the U/S as required complete all as specified and directed.

Danger notice plate of 1.6mm thick mild steel sheet vitreous enameled white with letters figures and conventional skull and in bones in signal red colour and fixed with MS clamps bolts and nuts of approved size for HT 25X20cm size complete all as specified and directed.

Cutting existing road / foot path bituminous macadam and PCC on foot path for laying protection pipe for cable and making good the disturbed surfaces of road/ foot path to match with the existing surface all as required, specified, and directed at site by Enge-in-charge. Note:- PCC wil be measured and paid seperately

Material & Labour for PCC 1:2:4 type B1 with 20mm graded stone aggregate for making good the disturbed hard standing complete all as specified and directed.

Supply and spread stone aggregate 45mm size for transformer yard/ HT 2 pole/4 pole structure after preparing the surrounding by brick work and removing the vegetation and making brick work and necessary surface excavation and spreading of layer of sand complete all as specified and as directed. Note:- (i) Earth work and brick work will be included in quoted rate. (ii) sand will be measured and paid separately

Material & Labour for preparation of old painted for 4 pole structure (outer exposed surface) of electric steel tubular poles/PCC over all dimension 8.5/9.0/11meters long, painting starts from 1.8 mtr above ground level including MS channel / angle iron and GI bracket/clamps with bolts, nuts of street light fitting and applying one coat of aluminium paint including writing pole No with black colur of existing size letters complete all as specified and as directed.

Material & Labour for preparation of old painted for 2 pole structure (outer exposed surface) of electric steel tubular poles/PCC poles of any size and apply three layers of yellow paint and three layer of black paint at the interval of 30cm each upto the total height of 1.8 mtr with synthetic enameled paint complete all as specified and directed.

Material & Labour in repairs for earthing complete with galvanized steel earth plate electrode of 60 cm x 60 cm x 6mm thick buried directly in ground [earth pit not less than 2.25 metre deep below normal ground level] with top edge of the plate not less than 1.5 m below normal ground level, connected to galvanized earth strip of 25x4mm by means of bolts, nuts, check nuts and washers of galvanized iron or steel all as shown in electrical plate No. 3 of MES SSR Part I connected to earth test point using earth strip of 25x4mm as earth lead all as specified and testing on completion including provision of earth lead protected by 40 mm dia light grade GI pipe & watering pipe shall be 20 mm bore medium grade GI pipe including all excavation and earth work in any type of soil, PCC pit with RCC cover, char coal, salt, funnel etc complete. Note :- Rate quoted by renderers shall be deemed to include for following provisions;-[i]. Excavation & earth work in any type of soil including removing of surplus material upto 50 M.[ii]. PCC 1:3:6 type C1 using 20mm graded stone aggregate in pit & 40mm thick precast RCC 1:2:4 type B1 cover 50x50 cm with 8mm TMT bars @ 10 cm C/C both ways with handles.[iii]. Main earthing lead from earth electrode to test point upto 7.5 mtr.[iv]. Funnel with watering pipe [GI pipe] 20mm bore [ISI marked] medium grade & copper lugs, charcoal & salt as reqd.[v]. GI protection pipe of size 40 mm bore light grade 7.5m.

Servicing of drop out fuse by replacing the unserviceable male and female contacts, connectors, replacing unserviceable nuts, bolts, washers, greasing, align properly insitu complete all as specified and directed. Note:- spares will be measured and paid separately

Supply & Fix top contact for DO fuse complete all as specified and directed.

Supply & Fix bottom contact for DO fuse complete all as specified and directed.

Supply & Fix contact/fix contact jaw for GOS complete all as specified and directed.

Supply & Fix Lightning arresters expulsion type complete with all fittings, transmission class, discharge capacity 65 kilo amp after removing the existing unserviceable including making necessary electrical connections complete all as specified and directed.

Supply & Fix in repair, GI pipe 80mm bore, light grade, laid below road / fixed along the poles / walls with necessary clamping, etc complete all as per specified and directed.

Supply & Fix in repair, GI pipe, 50mm bore, light grade, laid below road/fixed along the poles / walls with necessary clamping, etc complete all as per specified and directed.

Supply & Fix in repair, GI pipe, 40mm bore, light grade, laid below road/fixed along the poles / walls with necessary clamping, etc complete all as per specified and directed.

Supplying & laying, XLPE insulated PVC inner sheathed, 10 Sqmm, 2 core, armoured with galvanised steel strip or wire heavy duty underground cable with aluminium multi stranded conductor, 1100 volt grade, laid in trenches/duct, passing through pipe/duct or fixed on pole and connecting and testing complete including taking down old unserviceable cable complete all as specified and directed.

Material & Labour for preparation of old painted for chain link/Barbed wire fencing/gate/angle iron/PCC post of substation (outer exposed surface) painting starts from above ground level including MS channel / angle iron and GI bracket/clamps with bolts, nuts and applying two coat of aluminium paint / snowcem including writing substation details with black colour of existing size letters complete all as specified and as directed.

Removing the unserviceable bus connections, jumpers etc from the structure supply and fix bus bars/jumpers by 8mm thick bare aluminium conductor duly sleeve colour coding with Red/yellow/Blue and fixing for making rigid connections for HT 11 KV distribution with necessary nuts bolts clamps complete all as directed and as specified

Trimming / cutting of vegetation all around the main power house and sub station and disposing of the same to a distance not exceeding 50 mtrs and depositing where directed by Engr-in Charge.

Material & Labour for repair of unsv openable doors of existing LT panel by welding, replacing the locking arrangement complete all as specified and as directed.

Comprehensive maint with material and servicing of the Eicher vehicle No.03D-154729W, Transporting to Authorized Eicher Service centre/Dealer Checking the serviceability of the vehicle oiling, Engine tuning, overhauling fixture accessories replacement of first moving parts changing oil/fuel filters, replacement of bulbs, fuses, repairing of wiring, replacement/topuping of coolant, brake oil,, engine oil, cleaning and maint of radiators and Air Filter/Air Cleaner, maint of battery with electrolyte solution, distilled water, wheel alignment, Change of Wheel Greasing, Greasing of all mechanical moving parts, Checking of the Battery Charging system, Cotton waste, Micro fiber cloth, Cleaning brush and Cleaning of POL tank entire contract period as required and requirement of the following Eicher vehicles complete all as specified and directed by the Engineer-in-Charge. Note :- Replacement of spares if required other than mentioned in above will be paid separately under relevant item below.

Comprehensive maint with material and servicing of the TATA Mobile vehicle No. 08C- 083542A pick up van vehicles, Transporting to Authorized TATA Service centre/Dealer Checking the serviceability of the vehicle oiling, Engine tuning, overhauling fixture accessories replacement of first moving parts changing oil/fuel filters, replacement of bulbs, fuses, repairing of wiring, replacement/topuping of coolant, brake oil,, engine oil, cleaning and maint of radiators and Air Filter/Air Cleaner, maint of battery with electrolyte solution, distilled water, wheel alignment, Change of Wheel Greasing, Greasing of all mechanical moving parts, Checking of the Battery Charging system, replacement/providing of the floor mat, mud guard flab, Cotton waste, Micro fiber cloth, Cleaning brush entire contract period and as per manufacturer recommendation and requirement of the following TATA Mobiles/Zenon pick up van vehicles complete all as directed by the Engineer-in-Charge. Note :- Replacement of spares if required other than mentioned in above will be paid separately under relevant item below.

Comprehensive maint with material and servicing of the Vehicel No. BA. 22A-075992X (Make:- Hero Motorcycle) Transporting to Authorized Hero Service centre/Dealer Checking the serviceability of the vehicle oiling, Engine tuning, overhauling fixture accessories replacement of first moving parts changing oil/fuel filters, replacement of bulbs, fuses, repairing of wiring, replacement/topuping of Engine oil and Air Filter/Air Cleaner, maint of battery with electrolyte solution, distilled water, Checking of the Battery Charging system, Cotton waste, Micro fiber cloth, Cleaning brush, Cleaning of the POL tank entire contract period as required and requirement of the vehicle complete all as directed by the Engineer-in-Charge.

Taking down the existing defective Self starter from Eicher Vehicle and replacement of work out spares like Bendex drive, carbon brush, solinoid coil, Armature including rewinding stator, refixing in same position and testing complete all as specified and directed by the Engineer-in-charge

Taking down the existing defective Alternator from Eicher Vehicle and replacement of work out spares like Rotor Coil, Field coil, Rectifier, Electronic regulator with Carbon brush with Holder, refixing in same position and testing complete all as specified and directed by the Engineer-in-charge

Taking down the existing defective Self starter from TATA Mobile pick up Vehicle and replacement of work out spares like Bendex drive, carbon brush , solinoid coil, Armature including rewinding stator, refixing in same position and testing complete all as specified and directed by the Engineer-in-charge

Taking down the existing defective Alternator from TATA Mobile pick up Vehicle and replacement of work out spares like Rotor Coil, Field coil, Rectifier, Electronic regulator with Carbon brush with Holder, refixing in same position and testing complete all as specified and directed by the Engineer-in-charge

Dismantling and taking down Eicher vehicle defective clutch system and repair replacement of worn-out spare and refixing, testing complete all as specified and directed by Engineer-in-Charge Note : The rate for the minor parts required for repair other than the parts consider in the below is deem to be included.

Supply only the following spare parts of Eicher vehicle as per original manufacture:-

Clutch plate

Pressure plate with springs

Clutch cylinder

Sleeve cylinder

Release Bearing

Bush Bearing

Release Bearing lever along with spring Note:- Make for Item No. 57.01 TO 57.07 EICHER/TVS or Equivalent

Repair and overhauling of Eicher Vehicle defective shafting system and checking of parts such as propeller shaft, centre bearing, centre bearing clamp & rubber, universal cross, yok teeth and testing complete all as specified and directed by engineer-in-Charge. Note : The rate for the minor parts required for repair other than the parts consider in the below is deemed to be included in the quoted rates

Supply only the following spare parts of Eicher vehicle as per original manufacture:-

Centre bearing along with rubber

Universal cross

Yeok & teeth Note: Make for Item No 14.01 to 14.03 Eicher/TVS or Equivelent

Repair and overhauling of TATA Mobile pick up Vehicle defective shafting system and checking of parts such as propeller shaft, centre bearing, centre bearing clamp & rubber, universal cross, yok teeth and testing complete all as specified and directed by engineer-in-Charge. Note : The rate for the minor parts required for repair other than the parts consider in the below is deemed to be included in the quoted rates

Supply only the following spare parts of TATA Mobile/Xenon pick up vehicle as per original manufacture:-

Centre bearing along with rubber

Universal cross

Yeok & teeth Note: Make for Item No 61.01 to 61.03 TATA/TVS or Equivelent

Repair and overhauling of Eicher vehicle defective brake system and checking of parts such as wheel cylinder, master cylinder, wheel brake shoe, wheel brake spring system and testing complete all as specified and directed by Engineer-in-charge. Note : The rate for the minor parts required for repair other than the parts consider in the below is deemed to be included in the quoted rate.

Supply only the following spare parts of Eicher vehicle as per original manufacture:-

Wheel cylinder front right

Wheel cylinder front left

Wheel cylinder rear right

Wheel cylinder rear left

Master cylinder

Brake shoe (Front and rear side (Left & right)

Brake shoe spring & locking assembly Note: Make for Item No. 63.01 to 63.07:- TVS Grilling or Equivalent

Repair and overhauling of TATA Mobile pick up Vehicle defective suspension system and checking of parts such as shock absorber, front spring leaf, centre bolt, front spring leaf hanger, front spring leaf, shackle pin, rear spring leaf, rear spring leaf hanger, rear shackle pin and complete all as specified and directed by engineer-in-charge. Note : The rate for the minor parts required for repair other than the parts consider in the below is deem to be included in the quoted rate

Supply only the following spare parts of TATA Mobile pick up Vehicle as per original manufacture:-

Shock absorber bush

Shock absorber Front & Rear

Upper link

Lower link

Ball joint

Hanger

Shackle pin

Centre bolt

UJ Cross

Tie rod end,

Spring Leaf

Shackle plate with pin

Centre bearing

Centre bearing rubber

Centre bearing clamp

Yeok & teeth Note:- Item Serial No. 65.01 to 65.17- Make:- TATA/TVS or Equivalent

Taking down the existing defective fuel injection pump (FIP) alongwith injector for the Eicher vehicle engine and replacement of work out spares like delivery valves, Nozzles, bearings, fly weight, packing kit, and copper washer kit and recalibration of FIP alongwith governor and refixing in same position and testing of full load checking of pressure and checking the solinoid coil complete all as specified and directed by the Engineer-in-charge

Dismantling and taking down the gear box of TATA Mobile/Xenon pick up vehicle repair and overhauling including replacement of worn spare parts (spare parts will be measured and paid separately) refixing the same in original position and testing complete. Note : The rate for the minor parts required for repair other than the parts consider in the below is deem to be included.

Supply only the following spare parts of Tata Mobile as per original manufacture:-

Gear liver kit

Synchronizer(1 the to 4th gear)

Gear reverse pinion

Gear pinion Ist, 2nd, 3rd & 4th and 5

Counter Note: Make for Srl Item No. 68.01 to 68.05:- TATA/TVS or Equivalent

Taking out seat cover Front and back side of the vehicle Tata Mobile and replace the new seat cover stitching the worn out seat by filling seat materials of good quality and refixing the new one to their proper place neatly as directed. (Including all material use for fixing.)

Repair/Reconditioning of Engine cylinder head from Eicher vehicle by dismantling of engine head assy, rocker arm assy, inlet and exhaust valve etc., Transporting to private work shop, resurfacing of cylinder head assy including replacing of following items and lathe work & unloading, erection and testing, commissioning complete all specified and directed by Engineer in charge Note : Spare parts shall be measured and relevant items

The following items supply only:-

Head Gasket

In & Exhaust Valve

Minor Overhauling kit

Valve Guide

Repair/Reconditioning of Engine cylinder head from Tata Mobile vehicle by dismantling of engine head assy, rocker arm assy, inlet and exhaust valve etc., Transporting to private work whop, resurfacing of cylinder head assy including replacing of following items and lathe work & unloading, erection and testing, commissioning complete all specified and directed by Engineer in charge Note : Spare parts shall be measured and relevant items

The following items supply only:-

Head Gasket

In & Exhaust Valve

Minor Overhauling kit

Valve Guide

Removing wheel complete with tyre and tube, taking out tube repair, puncher of tube of vehicles Tata mobile.

All as per item Ser.No. 74.00 here in before but Eicher Vehicle

All as per item Ser.No. 74.00 here in before but Hero motor cycle.

Disconnecting the existing battery of capacity 12V 70 AH from the Vehicle, taking it to battery workshop, draining out the complete unserviceable sulphuric acid from the battery, filling up with new sulphuric acid to the required level, charging the battery, testing the battery for correct specific gravity, bringing back to the location, connecting to Vehicle for satisfactory function all as directed by Engineer-in-Charge.

Repair and Overhauling of Clutch and transmission system of Hero Motor cycle and carry out the repair including replacement of Clutch plate, spring circlips, transmission chain, sprocket set etc complete all as specified and directed by the Engineer-in-Charge

M&L for denting damage portion of vehicle including touching, welding, matching with existing painting with the same color of any vehicle complete all as specified and as directed.

Supply only dual head tire pressure gauge complete all as directed by the Engineer-in-Charge.

Supply only Hydraulic type jack (trolly Model) 2 ton capacity as per sample.

NOTE :- SCHEDULE OF CREDIT (Amount shall be deducted offline from the total quoted amount to workout the net contract sum to be considered for acceptance.) [(-) Rs 20,718.25 /- ]

KPELECTRICAL AND AUTOMATION