MAINTENANCE AND REPAIR TO JOINERY, PLUMBING, TILING WORK, PERIODICAL AND OTHER ALLIED B/R ITEMS TO JCOs/ OR MD ACCN AT SANYAT LINE, KARAM VIHAR, TIGRIS MOUDE LINE, SUMERAN LINE, NEW MOUDE LINE AND TO OTM ACCN IN THE AOR OF AGE B/R-I UNDER GE (EAST) D

Amount

Taking down chowkats or frames with shutters (without taking off shutters from the frames) including iron mangory not exc. 1.5 Sqm each complete all as specified and directed.

Taking down chowkats or frames with shutters (without taking off shutters from the frames) including iron mangory exc. 1.5 sqm but n.exc 4 sqm each complete all as specified and directed.

Taking down shutters of any description not exceeding 2.00 Sqm each complete all specified and directed.

S&F Pressed steel frames size 125mm x 60mm for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, including filling hollow portion of frame with PCC 1:3:6 Type C-0 using 12.5mm graded crushed stone aggregate etc., complete all as specified and as directed.

Pressed steel frames size 105mm x 60mm for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, including filling hollow portion of frames with PCC 1:3:6 Type C-0 using 12.5mm graded crushed stone aggregate etc., complete all as specified and as directed.

S & F framed work such as in door frame, door shuters / gate of angel or other section with gusset plates, rails, braces, etc complete , drilled for fixing of steel sheeting or other covering. Doors, etc to be prepared for hanging or sliding with and including either hooks and hings or steel hanging door fittings, including hings hold fast of Fe 410-W (Gde E-250 quality) etc complete all as specified.

S & F Framed work such as grills, gratings, etc.. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars, security grill over bdy wall (ornamental/designer type), gates, barred iron doors;ladders; framed balusters; walk ways; railings; frame work of water tanks and similar work conforming to Fe.290.Gde-E-165 complete all as specified and as directed. (No extra pament shall be paid for ornamental/designer pattern grills/gates, same shall be included in the quoted rates)

S&F solid PVC door frame of size 50mm x47mm made out of 5mm plain colour PVC sheet reinforced with MS square tube complete all as specified and directed.

S & F Factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, suppling & fixing in the frame at site as per specification & drawing.

S & F Solid PVC door frame of size 50mm x 95mm made out of wood grain printed PVC sheet used reinforced with M.S. tube, suppling & fixing in opening as per specification & drawing complete all as specified and as directed.

S & F Factory Made Solid PVC Moulded Door Shutters 28 to 30 mm thick (stile:), with 2,4 or 6 raised panel design with 2mm thick Moulded PVC Sheet on the front and back Face (wooden finish pattern), supplying & fixing in frame at site as per specification & drawing complete all as specified and as directed.

S & F 100mm size stainless steel butt hinges fixing with screws to PVC door frame complete all as specified.

S & F Aluminum Anodised 150mm size barrel tower bolt complete all as specified and as directed.

S & F 150mm size aluminum adodised handles complete all as specified and as directed.

S & F 100mm size Mild steel butt hinges fixing with screws to Iron door frame complete all as specified.

S & F Mild steel 150mm size barrel tower bolt complete all as specified and as directed.

S & F 150mm size Mild steel handles complete all as specified and as directed.

S & F 300 mm long Mild steel sliding door bolts, plate type, stove enamelled black, with bright bolt not less than 12mm dia with and including a minimum of 6 bolts and nuts, four on bolt plate and two on staple plate and fixed complete all as specified and directed.

S & F flush door shutter 35mm thick solid core construction with Block board and plywood face panels, commercial type on both sides. complete all as specified and as directed.

S & F 35 mm thick second class hard wood glazed and skelton shutters open rebated and prepared to receive glass, gauge etc (without sash bars) edges of framing plain, chamfered or rounded. fitted with cut and mitred beads for securing glass, etc sizes of members of shutters as specified in SSR Part -I section 8 clause 8.24 (a) supplied and fitted to chowkats

S & F for Factory made UPVC (white/Off white colour sliding window three track made out of extruded profiles with wall thickness of members as 2.3mm (1-0.2mm). Window profile with hollow section with multi chamber frame (108mm x 48mm) sash bars (42mm x 67mm). Sliding inter lock (one vertical length in each shutter 45.5mm x 28mm). Glazing head (24.5mm x 16mm) members will be mitred, cut and fusion welded in all corners including drilling of holes for fixing hardware and drainage of water. Making arrangement for fixing of hardware, EPDM gaskets 1.2, 1-0.2mm thick galvanised steel frame (30mm x 21.50mm). Sash bars (30mm x 18mm) profile to be inserted in required profile frame and will be fixed to the wall with 8mm x 100mm long fastners. Hardware : Touch lock to be of Zinc alloy (white powder coated), Steel roller system including 5mm thick glazing with selelcted quality glass, Aluminium track on bottom rail to be of hree track sliding frame, wool pine for sliding sash and interlock, complete all as specified and as directed. complete all as specifed and as directed. (Note:The unit rate quoted by contractor includes cost of glass and includes all other connected accessories. Net opening will be measured for payment purpose.)

S & F factory made uPVC white colour casement (Openable) Door made of extruded profile wilh wall thickness of 2.3mm ( + -0.2mm). Window profile with hollow section with mitlti chamber, frame (60mm x 58mm), sash (60mm x 78mm). T profile (One vertical length in between two shutters) (60mm x 74mm). Glazing bead (35mm x 20mm) will be mitered cut and fusion welded at all corners, including drilling ol holes for fixing hardware and drainage of water etc., making arrangement for fixing of hardware. EPDM gasket 1.2 + -0.2mm thick galvanized steel Frame (28mm x 21.5mm), sash (31mm x 27mm), T profile (27mm x 17mm) to be inserted in required profile, frame will be fixed to the wall wilh 8mm x 100mm long fasteners. Hardware: [casement door handle made of zinc alloyed (white powder coated). Corner striker. Secondary Strikers. Cylinder. Door transmission gear made of mild sleel with multi point locking system with strikes. 3D Hinges of zinc alloyed (white powder coated) and with stainless steel wiremesh (0.36mm nominal dia of wire and average width of apreture 1.40mm. (Note: The unit rate quoted by contractor include cost of wiremesh and all other connected accessories. Net opening will be measured for payment purpose.)

S&F Aluminium alloy powder coated windows including aluminum powder coated frames sliding track, bottom weighing not less than 1.015 Kg/RM, sides and top not less than 0.826 Kg/RM double revated and 0.55Kg/RM for window shutter with one fixed glazed shutter and two nos glazed/gauged shutter sliding type with aluminium sections as per series - A (15mm) 3 track of Jindal section numbers for sliding windwos with framed shutter including aluminium allow powder coated snap type beads handles with locking arrangement spring action and glazing clip joint cleats rubber gaskets etc including provision of 5.5mm thick tinted glass/frosted glass of superior quality and stainless steel jali including all standard fittings, complete all as specified and as directed.

S & F aluminium alloy powder coated glazed or skelton shutter including frame channel of section ( door frame single groove 85mmx45 mm x 1.25mm thick, shutter top section, bottom section, middle section and vertical section 65 mm x 45 mm x 1.25 mm thick and glazing clips weighing not less than 0.097 Kg/RM ) including shutter fixed to openable frame and channel as directed and as per IS specifications including S & F stainless steel wire cloth as required handles, tower bolt, door closer, locking arrangement Godrej, rubber gasket and door stopper complete.

S & F for Aluminum alloy powder coated door including frame and channel of section (Door frame single groove 101.6mm x 44.45mm x 2.1mm, shutter top section 47.62mm x 44.45mm x 1.95mm thick, shutter bottom section 114.30mm x 44.45mm x 2.15mm thick, shutter vertical section 85mm x 44.45mm x 1.80mm thick, shutter middle section 83.50mm x 44.45mm x 2.40mm thick & glazing clips weighing not less than 0.097 Kg/RM) including shutter fixed to sliding type/openable frame and channel as directed and approved by GE and as per IS specifications including provn of 5.5mm thick tinted glass/12mm thick prelaminated particle board as required including handles, tower bolt, floor spring heavy duty “SAMRAT” , locking arrangement “GODREJ”, rubber gasket and door stopper complete all as specified and as directed.

S & F Mild steel, plain, black sheet 1.60mm thick in wall cladding, steel gates and similar work, cut to size, holes punched; including round headed screws, clout nails or rivets and fixed to wood or steel framing with plain 40 mm lap joints with riveted or welded seams, including bending or turning up, mitred angles, etc. as required complete all as specified and as directed.

S & F in repairs stainless steel Curtain Rod 20 mm dia with holders fixed to wall with finials and bracket etc complete all as specified and as directed. (Note : Damage to Brick/stone or any type of wall and existing cement plaster/pointing during fixing of curtain rod/bracket/finial shall be make good and bring back to old position to be done by the contractor and the cost for the same shall be deemed to include in the quoted rate, No extra payment will be made for brick work, re-plastering and painting to the contractor.)

M & L for fabrication & fixing to horizontal & vertical shelves/ partations /sides/ top/ bottom/back sides etc for Modular kitchen cabinate/ wardrobe/ cupboard/drawers made out of 17/18 mm thick HDHMR boards with white laminated colour on both sides, of approved quality including paste to all exposed edge by edge Banding Tape including provision of cabinet for keeping baskets/ drawers etc and including taking down existing shutter/panel/partition and all other accessories in any type and any position complete all as specified and as directed. (Make :Action tesa or equivalent)

M & L for Fabrication & fixing to front side /all exposed sides of Modular kitchen cabinate/ wardrobe/ cupboard/drawers made out of 17/18 mm thick HDHMR boards with glossy/maat colour laminate sheet on front face and all exoposed sides and white laminate on other face of approved quality and including paste to all exposed edge by edge Banding Tape and including provision of cabinet for keeping baskets/ drawers etc and including taking down existing shutter/panel/partition and all other accessories in any type and any position complete all as specified and as directed. (Make : Action tesa or equivalent)

S & F for soft closure hinges with all fittings at mounting plate of premium quality, fixed in door/cup board shutters complete all as specified and as directed (Make : - Godrej/Hettich/IPSA).

S & F Continuous (piano) hinges, stainless steel, width of flap 30mm complete all as specified and as directed.

S & F 150 mm size designer door handel stainless steel cromimum plated for Cabinet/Wall Unit/Overhead Unit/Wardrobe etc complete all as specified and as directed.

S&F mortice night latch of size 75 mm, 4 levers of mild steel etc complete all as specified and as directed.

S & F for Magnetic catches with steel body ‘H’ type, fixed to shutter, complete all as specified.

Supply only Stainless steel plain basket of size 445mm x 485mm x 200 mm made of min 4mmdia stainless steel wire and bottom of S S perforated sheet approved quality with suitable arrangement for fixing over telescopic channel 18 inches/ 20 inches in length two way extruded MS galvanised over rollers as approved by Engr-in-Charge. (Make: Godrej Cat part No 3892, or equivalent in IPSA/ Hettich as approved by Engr-in-Charge).

Supply only for Stainless steel thali/plate basket of size 445mm x 485mm x 200 mm made of min 4mmdia stainless steel wire of approved quality with suitable arrangement for fixing over telescopic channel 18 inches/20 inches in length two way extruded MS galvanised over rollers as approved by Engr-in-Charge. (Make: Godrej Cat part No 3441or equivalent in IPSA/ Hettich as approved by Engr-in-Charge).

Supply only Stainless steel basket (Perforated Cutlery Basket SS) of size 445mm x 485mm x 100mm made with suitable arrangement for fixing over telescopic channel 18 inches/ 20 inches in length two way extruded MS galvanised over rollers as approved by Engr-in-Charge. (Make: Godrej Cat art No 3575 or equivalent in IPSA/Hettich as approved by Engr-in-Charge).

Supply only Stainless steel two shelf pullout basket of size 150 mm x 450mm x 430 mm made of min 4mmdia stainless steel wire and bottom of S S perforated sheet approved quality with suitable arrangement for fixing over telescopic channel 18 inches/ 20 inches in length two way extruded MS galvanised over rollers as approved by Engr-in-Charge. (Make: Godrej Cat part No 2260, or equivalent in IPSA/ Hettich as approved by Engr-in-Charge).

S & F in repairs ready made floor/wall mounted Vanity box made of HDHMR board, both side laminated consisting of the following combination :- (a) Wash Hand Basin 810mm x 500mm. (b) Base Cabinet 780mm x 485mm x 460mm. (c) Side Cabinet 300mm x 250mm x 1800mm. (d) Mirror cabinet size 780mm x 160mm x 800mm. Make : Hindware - Cat Part No. 70089 or 70084. Make : Kohler : Cat Part No. K-31602IN-E63

S & F in repair for Wall mounted multiple function Shower Panel including all acessories and fittings, complete all as specified and as directed. Make : Hindware Cat Part No. 511686 (size 1650mm x 150mm x 550mm)/Jaquar Cat Part No. JPL-SSF-ST88148B(size 1600mm x 200mm) or JPL-WHT-TMCURVENEO (size1500mm x 230mm) or eqivanlent in Cera/Somany

M&L 4mm thick desginer board false ceiling e- board ( Make : Everest or equivalent as approved by GE) in ceiling fixed with screw as per manufactures instruction, fixed with white powder coated galvanized iron grid with 24mm wide T-section exposed flanges comprising of main runner made from 0.33 mm thick galvanized steel sheet & size T-24x32 mm and spaced at 1.2m c/c securely fixed to the structural soffits by hangers at 1.2m of GI wire 2 mm dia fixed rawl plug, level adjusters and screws etc. The last hanger at the end of each main runner shall not be greater than 450mm from adjacent wall flush fitting of 1200mm long cross tee with (double stitching) to be inter locked between main runner at 600 mm c/c to from 600 x 600 mm modules, angle along perimeter wall shall be of 0.45mm thick galvanized steel of size 19 x19 mm of white colour all as per instructionand including dismantling of walls and celing existing old board (fibre pulp.insulation etc)or insulation boards/slabs/blanks any thickness including cover fillets , any type of frame etc. complete all as specified and directed.

S & F plain gypsum board panel 12 mm thick on false ceiling ( including any design/ cob design as required & pattern as approved by GE) with and including necessary GI frame work for seamless ceiling used with ' T ' , channel or any section including screws , cleats ,fasteners, clips and all required accessories , hangers etc of galvanized steel all as per manufacturer design conforming to IS-2095 and 2542(1981) the weight of the board shall be not less than 7 kg per sqm and including dismantling of walls and celing existing old board (fibre pulp.insulation etc)or insulation boards/slabs/blanks any thickness including cover fillets etc including two coat of OBD over a coat of putty including dismantling of walls and celing existing old board (fibre pulp.insulation etc)or insulation boards/slabs/blanks any thickness including cover fillets etc. complete all as specified and directed.

M&L PVC hollow wall panelling 7 to 8 mm thick wood grain teak finished (colour and design as approved by GE) prelaminated inclusive of fixing on to wall including moulding end caps with L / U beading etc fixed with PVC sleeves and screws as required at site including dismantling of old wall panelling of any description, complete all as specified and as directed. Note : (i) Taking down existing any type of electric board sheet/ tube light/ LED / any fittings before fixing of panels and refixing the same after fixing the panels as required are included in the quoted rates by the contractor.

S & F horizontal / vertical Polyester blinds curtain for winows (colour and design as approved by GE ) with curtain rod fixing arrangements etc including dismantling of old curtians blinds of any description, complete all as specified and as directed.

M & L for Washed stone grit plaster on exterior walls in two layers (colour and design as approved by GE), under layer 12mm cement plaster 1:4 (1 cement: 4 coarse sand ) furrowing the under layer with scratching tool, applying cement slurry on the under layer @ 3 Kg of cement per square metre, top layer 15mm cement plaster 1:1/2:2 (1 cement: 1/2 coarse sand : 2 stone chipping 10mm nominal size) in panels with groove all around as per approved pattern (groove of uniform size 15mm wide and 15mm deep in the top layer of washed stone grit plaster as per approved pattern using wooden battens, nailed to the under layer including removal of wooden battens, repair to the edges of panels and finishing the groove) complete including scrubbing and washing, the top layer with brushes and water to expose the stone chippings including taking down of existing cement or cmenet lime plaster of any thickness and any description on brick or stone walls including raking out joints, hacking for key and scrubbing down woith water, complete all as specified and as directed.

M & L for coloured vetrified tiles of size 600 x 600 x 8-10mm thick as in floor over and including 15mm thick screed bed 1:6 in cement mortar, set and jointed in neat cement slurry and pointed in white or coloured cement to match after dismantling floor, hearth or wall tiling with cement mortar bedding (but not backing), complete all as specified and as directed.

M & L for Vitrified coloured tiles dark shade 8-10mm thick (square/rectangular) polished, area of each tile exc 0.42 sqm but n exc 1.00 sqm each in floors etc., set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15 mm thick screed bed in cement mortar 1:6, after dismantling floor, hearth or wall tiling with cement mortar bedding (but not backing), complete all as specified and as directed.

M & L for Non-Skid coloured ceramic tiles 7-8mm thick (square/rectangular) of size 300mmx300mm or 400mmx400mm in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15mm thick screed bed in CM 1:6, after dismantling floor, hearth or wall tiling with cement mortar bedding (but not backing), complete all as specified and as directed.

M & L for glazed ceramic tiles in vertical surface of size 300mmx450mm or 300mmx600mm and 7-8 mm thick set and jointed in neat cement slurry and pointed in white or coloured cement to match over and incl 10mm thick screed bed in CM 1:4 after dismantling floor, hearth or wall tiling with cement mortar bedding (but not backing), complete all as specified and as directed.

M & L 20-22 mm thick granite (Type, Size and colour as approved by GE and as per site requirement) of any type work table rubbed and polished as in floors, steps, jambs, pillars, window cills, cooking platforms and like in over and incl 15mm thick cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite slab , notching, moulding and polishing after dismantling of old granite of any type with cement mortar bedding (but not backing), complete all as specified and as directed .

M & L for Machine cut kota stone slab flooring 18-20mm thick over and including 15mm thick cement screed base in CM 1:6 laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including grinding and mirror polishing after dismantling of existing kota stone or any other type of flooring with cement mortar bedding (but not backing), complete all as specified and as directed.

S & F Pre-painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50 mm thick of any colour having tensile strength of 550 Mpa as in roof covering/ cladding to wall / view cutter etc, fixed with self tapping screws with bent to a curve (of any radius as per required) including dismantling asbestos cement sheet in roof coverings ( corrugated , semicorrugated etc) any gauge, thickness, including , Nainital or similar pattern roof coverings in any pattern & position of roof coverings.complete all as specified and directed (Note : This item is also considered for old existing roof /wall covering partly repair with existing any type of sheet )

S & F Pre-painted galvalume aluminum zinc coating GI based plain steel sheet 0.50 mm thick of any colour as in ridges hips, vally gutter, drip and straight flashing , fixed with self tapping screws etc including dismantling asbestos cement sheet in roof coverings ( corrugated , semicorrugated etc) any gauge, thickness, including , Nainital or similar pattern roof coverings in any pattern & position of roof coverings.complete all as specified and directed

Demolition of cement concrete (unreinforced) in ground floor or in any position and paving not exc. 15 cm thick (below or above ground level) complete all as specified and as directed.

M & L 75 mm thick Cement concrete work as in plinth protection type C-1 , 1:3:6 (20mm graded aggregates) with finishing cement concrete surface even and smooth without using extra cement complete all as specified and directed

M & L for 75mm thick Cement concrete 1:4:8 Type D-2 (using 40mm graded agg) as in sub base of flooring or in any position including demolition of cement concrete (unreinforced) in ground floor or in any position and paving not exc. 15 cm thick (below or above ground level) complete all as specified and as directed.

M & L for Machine pressed precast conctete interlocking paver block of any shape and size (Two colour combination) confirming to IS 15658-2006 of 60 mm thick, M-35 Grade laid dry in floor/path with 50 mm thick sand bedding layer after dismantling of old interlocking tiles /path etc and remove from the MoD land complete all as specified and as directed. complete all as specified and as directed.

M & L for Coloured Chequered cement concrete tiles 30cm x 30cm x 20-22mm thick, set, jointed and pointed in neat cement slurry over and including 15mm thick screed bed in CM 1:6 etc after dismantling of existing chequired tiles of any type complete all as specified and as directed.

S & F Brand factory made WPC railing combining WPC board/Fancy designer type grating and WPC frame 100% solid WPC (wood polymer composite) railing of required length and of 2' to 2.5' height , comprising of virgin PVC resin of K value 58-60 (Suspension Grade), Calcium Carbonate and natural fibres (Wood Powders/rice husk//wheat husk) and non toxic additives, made from single extrusion process, WPC foam board with having minimum density 650kg/cbm and WPC frame having minimum density 780kg/cbm having good screw holding capacity (screw withdrawal strength of 2000N (Face) & 1100N (Edge) , Minimum comprising of 50N/mm2, Modules of elasticity 850N/mm2 and resistance of speed of flame of class A category with property of being termite/Borer free water /Moisture proof and fire resistance. For WPC railing WPC jali to be fixed with WPC frame of size 75x50mm with necessary supporting lengths at vertical as well as horizontal at wall frames to be fixed with 3"x3" GI 'L' or SS cleats to support vertical frame lengths including dismantling of existing RCC jallies with frames complete all as specified and as directed. (Make : Rajshree or equivalent) (Note : The said item shall be fixed over boundary walls/roof tops and in any other positions as requirement at site)

M&L providing and applying the plaster with single component ready to use repair mortar capable of applying 20 mm average thickness in single layer and finishing with trowel with a bond coat : SBR polymer (@ 10% of cement weight) modified cementious bond coat @ 2.2 kg cement/Sqm of surface area complete. {Make: SMART CARE REPAIR MORTAR (ASIAN PAINTS) / RENDEROC SP-40 (FOSROC) / MONOTOP F122 THEXO TROPIC (SIKA)}. Note : (a) All materials shall be procured directly form manufacturer or their authorised dealer. (b) The application shall be executed on any type of surface and on horizontal/Vertical areas. (c) Full quantity of repair mortar shall be entered in MB as "NOT TO BE ABSTRACTED".

Providing and applying fibre reinforced elastomeric liquid water proofing membrane formulated with reinforcing acrylic fibers having Sun Reflectivity Index (SRI) of 105 on horizontal/vertical surfaces of roof/wall/chajjas in multiple coats @ 2.0 litre/sqm. Primary coat is self-priming coat of elastomeric waterproofing liquid (dilution with water in the ratio of 3:1, damp proof : water) and other coats to be applied undiluted. The coating needs to be reinforced with 40 GSM geotextile, to sandwiched between 2nd & 3rd coat of coating. The application shall be carried out after scrapping and properly cleaning the surface to remove loose particles with wire brushes complete in all respect as per the direction of Engineer-in-Charge. Make: Smart Care Damp Proof of Asian Paints or equivalent in SIKA/BERGER/ FOSROC/STP. Notes: (a) The work shall be executed through authorised applicator of manufacturer only. (b) Authrised Applicator shall be approved by GE before starting of work. (c) All materials shall be procured directly form manufacturer or their authorised dealer. (d) Guarantee: The contractor shall furnish a written guarantee for the effectiveness of the water proofing treatment for a period of Eight years in favour of the GE. A sum equivalent to 2.5% (Two point Five Percent) of the cost of water proofing treatment shall be retained by the Govt from the contractor’s dues as security deposit. The contractor may, however, furnish a fixed deposit receipt in lieu from a Schedule bank pledged in favour of Garrison Engineer. (e) Full quantity of water proofing chemical / paint shall be entered in MB as "NOT TO BE ABSTRACTED".

S & F in repair Vitreous China wash down pedestal pattern EWC, white and including with PVC (SWR) ' S' Trap with connection to drain and to flushing pipe antisyphonage pipe, and making good to floor complete all as specified and directed.

S & F in repair Vitreous China squatting pan 'Orissa' pattern size 580 x 440 mm white, with integral foot rests with connection to trap , and to flushing pipe antisyphonage pipe including trap set in and including concrete etc complete including making good to floor all as specified and dirtected.

S & F in reapir 10 Ltrs capacity PVC valveless symphonic action type flushing cistern white low level with inlet, ball valve float handle including bracket etc complete all as specified and directed

S & F in repairs Vitreous china single Piece floor mounted WC With PP Soft Close Seat Cover, Hinges, with cistern & Dual Flush Cistern Fitting, Fixing Accessories and Accessories Set, Size: 360x730x740 mm, S Trap- 300 mm including connecetion to drain pipe with all fitting and fixture complete all as specified and as directed. Make & Cat Part : Jaquar-Cat No. SLS-WHT-6851S300PP or equivalent in Marc / Kohler )

S & F in repair Vitreous China wash basin, white, flat back, size 550 x 400 mm including , chain and plug but including brackets or erecting stand including & (32 mm -45 gms/40mm-60 gms ) waste coupling of CP complete all as specified and dirtected by Engr-in-Charge .

S & F in repair Vitreous china wash basin counter oval type size 600x425x195mm, under any type of slab with all fitting and fixture, & (32 mm -45 gms/40mm-60 gms ) waste coupling of CP complete all as specified and as directed. (Make : Jaquar / Hindw are/Parryware/cera)

S & F in repairs Vitreous china urinal (White/Off white) type size 420mm x 395mm x 635mm fixed including all fixing accessories (Such as fastener for fixing, 01x waste pipe, 01 x PVC connection, 01 x Pusch Cock CP) complete all as specified and as directed. Make : Parryware/Cera/Hindware.

S & F in repair 15 mm bore Fancy type pillar taps, Cast Copper alloy, with capstan heads, chromium plated, screwed down high pressure with or without lettered Hot or Cold with long screwed shanks and fly nuts, screwed for iron pipe and fixed. complete all as specifed and directed. (Make: Jaquar/ Marc/ Kohler)

S & F in repairs Bib tap standard of PTMT any colour high pressure screwed for iron pipe and fixed complete all as specified and as directed. (Make : Prayag/Prince/polytuf)

S&F in repairs 32 mm bore PVC waste pipe with fittings of approved make suitable for WHB, Urinals and Sink etc all as specified and directed.

S & F PVC connections 15mm size with PTMT nuts of length 600mm complete all as specified and as directed. (Make : Prayag/Prince/polytuf)

S&F in repairs 75mm dia brass chromium plated shower rose with neck and swivel joints fancy type suitable for 15mm bore GI pipe all as specified and directed. (Make: Jaquar/ Marc/ Kohler)

S & F in repair 15mm bore, fancy type CP bib tap (Long Body) of cast copper alloy with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule complete all as specified. (Make: Jaquar/ Marc/ Kohler)

S & F in repairs Fancy type sink mixer for mixing hot and cold water with swinging port, screwed for iron pipe,15mm bore complete all as specified and as directed. (Make : Jaquar/Marc/Kohler)

S & F in repairs Brass CP basin mixer central hole, for mixing hot and cold water fixed as per manufacture's manual, with long shunk and cup washers, screwed both ends suitable for 15mm bore GI pipe joints to GI pipes or unions, complete all as specified and as directed. Make & Cat Part : Jaquar-Cat No. KUP-35051BPM, Jaquar-Cat No. KUP-35005BPM, Kohler-Cat No. K-74013IN-4BND-CP, Kohler-Cat No. K-74026IN-4BND-CP.

S & F in repairs Brass chromium plated wall mixture 3 in 1 system with provision for hand shower and overhead shower and suitable for 15mm bore GI pipe including three joints to steel pipes or unions and plugging and screwing to walls, fixed in repairs, complete all as specified and as directed. Make & Cat Part : Jaquar-Cat No. CON-281KN, Jaquar-Cat No. COP-281PM Kohler-Cat No. K-98754IN-4-CP.

S & F in repairs Sinks (Double bowl) made of stainsless steel 1mm thick as in kitchen with plugs, washers and wastes, including bedding in cement mortor on to dwarf walls or including cantilever brackets and connecting union to pipe overall size 915mmx460mm, double bowl (each bowl size 410mm x 330mm x 160mm), fixed in repairs, complete all as specified and as directed. (Make : Nirali/Jayna/Diamond)

S & F in repairs Sinks with drainage board made of stainsless steel 1 mm thick kitchen or laboratory with plugs, washers and wastes, including bedding in cement mortor on to dwarf walls or including fixing cantilever brackets and connecting union to pipe overall size 915mmx460mm bowl size 410mmx330mmx 160mm all as specified and directed. (Make : Nirali/Jayna/Diamond)

S & F in repairs Angle valve of CP any colour high pressure screwed for iron pipe and fixed, complete all as specified and as directed. (Make: Jaquar/Marc/Kohler)

S&F in repairs health faucet chromium plated brass with 1.00m CP long flexible pipe and brass chromium plate nuts completed. (Make - Cera Cat No. F8030103 / Hindware Cat No. F 160068 CP / Jaquar Cat No. ALD- 573)

S & F CP brass jet spray for EWC with 1mtr long flexible stainless steel connecting pipe 15mm bore, fixed in repairs, complete all as specified and as directed.

S & F in repairs Toilet paper holder chromium plated with flap all as specified and directed. (MAKE : JAQUAR/MARC/KOHLER).

S&F in repairs Stainless Steel grating jalli with central hole 125mm dia suitable for Nahani trap or in any place complete all as specified and as directed.

S & F in repairs 20mm dia Chromium plated towel rail 60cm long fixed to wall including all fittings for fixing complete all as specified and directed. (Make : Jaquar/Marc/Kohler)

S & F in repairs Sheet glass shelf assembly consisting of 5.5mm thick sheet glass shelf 12cm wide with chromium plated bracket guard and railing 60cm long complete all as specified and as directed. (Make : Jaquar/Marc/Kohler)

S & F in repairs glass corner shelf assembly consisting of 5.5mm thick sheet glass shelf 12cm wide with chromium plated bracket guard and railing 60cm long complete all as specified and as directed. (Make : Jaquar/Marc/Kohler)

S & F in repairs Designer type high quality fancy type looking mirror of size as approved by Engr-in-Charge 8-10mm thick, fixed to wall with stainless steel studs, screws, brackets and washers etc complete all as specified and as directed.

S & F in repairs 15mm bore Gun-metal, globe or gate valves, with iron wheel head screwed for iron pipe of 15 mm bore complete all as specified and directed.

S & F in repairs 20mm bore Gun-metal, globe or gate valves, with iron wheel head screwed for iron pipe of 15 mm bore complete all as specified and directed.

S & F in repairs 25mm bore Gun-metal, globe or gate valves, with iron wheel head screwed for iron pipe of 15 mm bore complete all as specified and directed.

S & F Rotational moulded polyethylene water storage tanks 1000 lts capacity, tripple layered (cylindrical vertical with closed top) hoisted and fixed in position with 20 mm dia PTMT ball valves, high pressure, with polythene float and flynut complete, screwed for iron pipe or brass ferrule and fixed including taking out existing unserviceable overhead tank of any description complete.

S & F Rotational moulded polyethylene water storage tanks 2000 lts capacity, tripple layered (cylindrical vertical with closed top) hoisted and fixed in position with 20 mm dia PTMT ball valves, high pressure, with polythene float and flynut complete, screwed for iron pipe or brass ferrule and fixed including taking out existing unserviceable overhead tank of any description complete.

S & F GI tubing 15mm bore medium grade, galvanised, ISI marked with all fitting and fixed complete to walls and ceilings or laid in floors including taking up or down GI tubing 15mm bore and connections complete all as specified and directed.

S & F GI tubing 20mm bore medium grade, galvanised, ISI marked with all fitting and fixed complete to walls and ceilings or laid in floors including taking up or down GI tubing 15mm bore and connections complete all as specified and directed.

S & F in repair Aluminium ( Die cast ) body door closer hydraclically regulated designation No. 3 universal type suitable for door shutters of 701 to 850mm in width and of weight between 61 to 80 kg, fixed in repairs, complete all as specified and as directed.

S & F Galvanised mild steel wire cloth 0.63mm nominal dia of wire and average width of aperature 1.4mm and fixed to doors and widows with necessary 12mm iron flats with welding and including complete all as specified and directed. (Rates are inclusive of welding and supply of flats including reqd nutbolts wherever required)

S & F 3mm thick sheet glass, ordinary quality and glazing with wooden beading not exc 0.5 Sqm in each pane all as specified and directed including hacking out old broken glass (any thickness, size, quality or description) from wooden or steel frame glazed with putty or fixed with beads.

S & F 110mm dia PVC (SWR) pipes single socketed in any length with rubber rings joints fixed to walls or laid in floors as sanitary fittings, rain water pipes etc in any position including taking down sanitary pipes, eaves gutters and rainwater pipes (any size or pattern), in any type and position including all fittings,heads,shoes, bends, swan-necks, branch pieces, couplers, reducers, vent cowl, stack clamps etc. complete all as specified and directed.

S & F PVC (SWR) 110mm bore bends with access door, complete all as specified and directed.

M & L for Brick work with sub class 'B' bricks of old size, straight or curved on plan to any radious built in CM 1:6 including demolition of Brickwork built in cement mortar including all quioins, arches, pillars etc complete all as specified.

Taking down cement or cement lime plaster , any description on brick or stone walls, ceilings or concrete surfaces etc including raking out joints, hacking for key, scrubbing down with water etc complete all as specified and as directed.

M & L for 15mm thick rendering in cement mortar 1:4 on fair face of brick walls/ concrete surfaces and finished even and fair in any position incl scafolding etc, complete all as specified and as directed.

M & L for 15mm thick rendering in cement mortar 1:6 on fair face of brick walls/ concrete surfaces & finished even and smooth without using extra cement in any position incl scafolding etc, complete all as specified.

M & L rendering 10 mm thick on concrete surfaces as in ceiling in CM 1:3, finished even and fair including complete all as specified and as directed.

M & L for preparation of Old decorated surface after complete removal of existing surfaces of external wall/ ceiling applying 2 coats of Exterior Acrylic Emulsion Paint of Dr. Fixit Sureseal or equivalent of Asian Paints or Berger over 2mm wall care putty and coat of primer complete all as specified and as directed.

M & L for preparation of Old plastered or un-plastered surfaces of internal wall/ceiling after complete removal of existing surfaces of any type and applying 2 coats of Internal acrylic paint of Dr. Fixit Sureseal or equivalent of Asian Paints or Berger over 2mm wall care putty and coat of primer complete all as specified and as directed.

M & L for preparation of new plaster external wall and ceiling surfaces of and applying Two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm complete all as specified and as directed.

M & L for Preparation of newly plastered /unplastered surfaces of walls and ceilings and applying Two coats of Oil Bound Distemper on wall surfaces over a coat of primer ,complete all as specified and directed.

M & L for preparation of plastered or unplastered old decorated surfaces of walls including brooming down or scraping down with steel wire brushes of smoke spots , moulds ,moss efflocerent salts and treading oil and greasy spots, filling the cracks, holes with POP/Putty and applying One coat of Oil bound distemper complete all as specified and directed.

M & L for preparation of plastered, unplastered or pointing old decorated surfaces of walls including brooming down or scraping down with steel wire brushes of smoke spots , moulds ,moss efflocerent salts and treading oil and greasy spots, filling the cracks, holes with POP/Putty and applying One coat of Cement Based Paint complete all as specified and directed.

M & L for preparation of plastered, unplastered or pointing old decorated surfaces of walls including brooming down or scraping down with steel wire brushes of smoke spots , moulds ,moss efflocerent salts and treading oil and greasy spots, filling the cracks, holes with POP/Putty and applying One coat of exterior acrylic emulsion paint of any tint all as per manufacturers instructions to achive desired finish at any height complete all as directed. Note :- 1. Stage for prepration of surfaces shall be got approved from GE before applying the finishes. 2. Make : BERGER (WEATHER COAT LONG LIFE 10), ASIAN (APEX ULTIMA), NEROLAC (EXCEL MICA MARBLE), DULEX (WEATHER SHIELD MAX)

M&L two coat of synthetic enamel paint (finishing coat) over one coat of pink primer to new wood surfaces of any description over 10 cm width or girth incl prepration of surfaces complete all as specified.

M & L for One Coat of Synthetic Enamal Paint on wooden surfaces including prepration of Old surface of any description, over 10cm in width or girth complete all as specified and as directed.

Preparation of new steel surfaces of any description over 10cm width or girth and applying two coats of synthetic enamel paint over one coat of red oxide zinc chrome primer, complete all as specified.

M & L for One Coat of Synthetic Enamal Paint on steel surfaces including prepration of Old steel surface of any description, over 10cm in width or girth complete all as specified and as directed.

Dismantling wrought iron or mild steel work of any description not otherwise provided for complete all as specified and as directed by Engr-in-Charge.

S&F steel work in tubular trusses including special shaped washer etc complete using ERW or induction butt welded tubes conforming to IS 1161-1979 grade St.- 240 complete.

S&F for 2mm thick Fibre glass reinforced translucent plain/ corrugated sheeting with two corrugations side lap fixed with coach screw and washer in roof, wall gate etc including dismantling of existing sheet of any type complete all as specified and as directed.

Akhil Enterprises (BID ID -3165577)

A R construction (BID ID -3165390)

M/s Shubh Enterprises (BID ID -3165648)

sunil traders (BID ID -3171158)

Vipul Construction (BID ID -3165552)

tarun construction co (BID ID -3164312)