Loading
Loading…
Loading…
| # | Company | Amount | Rank | Status |
|---|---|---|---|---|
| 1 | L1₹38.7 LAccepted-AOC HOUSE NO 41 WARD NO 09 ARYA SAMAJ GALI UDHAMPUR 182101 J K | UDHAMPUR | UDHAMPUR | J K | 182101 | L1 | Accepted-AOC Accept | |
| 2 | L2₹41.0 L+₹2.0 L (5.07%)Rejected-Finance SHOP NO 6 BENGALI CLUB MIDDLE POINT SRI VIJAYA PURAM 744101 | SOUTH ANDAMANS | ANDAMAN AND NICOBAR ISLANDS | 744101 | L2 | Rejected-Finance Not being L1 | |
| 3 | L3₹43.5 L+₹4.5 L (11.4%)Rejected-Finance | L3 | Rejected-Finance Not being L1 | |
| 4 | L4₹44.7 L+₹5.6 L (14.5%)Rejected-Finance | L4 | Rejected-Finance Not being L1 | |
| 5 | L5₹55.0 L+₹16.0 L (41.0%)Rejected-Finance | L5 | Rejected-Finance Not being L1 |
| Sl No | Description | Qty | Unit | ICON AGENCIES L3 | NAVJEEVAN ENTERPRISES L4 | M/S. RUDRA ENTERPRISES L5 | Bharat Udyog L2 | M/S N.K. POWER SYSTEMS AND PROJECTS L1 |
|---|---|---|---|---|---|---|---|---|
| 1.00 | Dismantling old defective conventional control LT panels of POWER generation system and Supply, installing, testing and commissioning of microprocessor based LT feeder pillar box factory made cubical indoor type, fabricated out of 2.00 mm thick CRCA sheet with angle iron frame/channel made of suitable size at vertical corners & base of Panel board floor mounted, dust and vermin proof, suitable for voltage 415 V 3 Phase 4 wire weather proof, with IP- 43 protection, with separate hinge door for each compartment with locking arrangement, with back door common openable (Screwed), grouted in PCC (1:2:4) type B1 complete including painting with two coats of epoxy powder paint over a coat of primer after under going a rigorous metal treatment process involving alkaline degreasing, descaling in dilute sulphuric acid or any other acid and phosphate and with aluminium busbar (TPN+E), suitable double compression copper cable glands all as specified and directed by Engineer-in-Charge and including provn of the following:-
Note: The panel shall be of similar CPRI type tested panel and quoted rate inclusive of PCC foundation and panelised/compartmental for easy assembling at site.
i) Aluminium Bus bar 5000A- mounted on porcelain insulator - 01 Set (Set of 4 Nos) with PVC sleeve insulation and copper earth strip of size 50x6 mm.
ii) Microprocessor based Synchronization Controller - 3200XT
Make : Woodward - 3 Nos.
iii) 1250A, 4P, EDO ACB, with UV & Microprocessor based for Incoming L&T / Schnieder - 3 Nos.
iv) 1250A, 4P, MDO ACB, with Microprocessor based for Load L&T / Schnieder - 2 Nos & 1600A, 4P, MDO ACB, with Microprocessor based for Load L&T / Schnieder - 1 Nos. | 1 | Each Set | 33,90,000 ₹33,90,000 | 34,50,000 ₹34,50,000 | 38,00,000 ₹38,00,000 | 28,33,713 ₹28,33,713 | 24,00,000 ₹24,00,000 Lowest |
| 2.00v) Digital smart meter with remote monitoring systm / MFM Meter V, A, F, PF, KW Make : Schnieder/ Elmeasure - 6 Nos vi) Hooter for Fault Notice Make Venex - 3 Nos. Vii) Contactors Auxilliary Contactors Make L&T / Siemens - 30 Nos. Viii) Control MCBs Make L&T / Siemens -1 Set. ix) CTs 2000-1600/5A CT Make Harris / Shreshta - 18 Nos. x) Selector switches 3 pole, 4 Way, 16A Make Salzer -6 Nos. xi) Push Button Make Tecknic / Essbee -6 Nos. xii) 30 V DC SMPS battery charger with 2v 100AH dry cells of suitable capacity -1 set and BCU Battery charging unit - 24V 10A Make KB/Kensys 3 Nos. xiii) Emergency Stop switch Make Esbee - 3 Nos. xiv) TNC Switch L&T / Gorlon 6 Nos. xv) DC Ammeter 10-30A Make Rishabh / EAPL - 3 Nos. xvi) DC Voltmeter 10-50V Make Rishabh / EAPL - 3 Nos. xvii) Wiring & Other accessories 1 Sqmm Copper flexible Control wiring with pre-printed ferrules RR / Polycab - 3 Jobs. xviii) One Nos spare compartment with busbar extension complete for future expansion. | ||||||||
| 3.00 | Dismantling old defective conventional controller panel and Supply, installing, testing and commissioning of microprocessor based LT feeder pillar controller box factory made cubical indoor type, fabricated out of 2.00 mm thick CRCA sheet with angle iron frame/channel made of suitable size at vertical corners & base of Panel board floor mounted, dust and vermine proof, suitable for voltage 415 V 3 Phase 4 wire weather proof, with IP- 43 protection, with separate hinge door for each compartment with locking arrangement, with back door common openable (Screwed), grouted in PCC (1:2:4) type B1 complete including painting with two coats of epoxy powder paint over a coat of primer after under going a rigorous metal treatment process involving alkaline degreasing, descaling in dilute sulphuric acid or any other acid and phosphate and with copper control wiring, suitable double compression copper cable glands and including provn of the following:- Note: The panel shall be of similar CPRI type tested panel and quoted rate inclusive of PCC foundation and panelised/compartmental for easy assembling at site.
a) Cummins Governor Cord – 1 No
b) Stamford AS440 AVR – 1 No
c) Deep-Sea 7320 Engine Controller – 1 No.
d) 2mm Thick CRCA sheet Panel with necessary
auxiliaries, Relay cord, Emergency Stop button,
Control Supply on/off button Etc,
e) complete harness wiring | 1 | Each Set | 1,85,000 ₹1,85,000 Lowest | 1,93,200 ₹1,93,200 | 1,95,000 ₹1,95,000 | 7,87,357 ₹7,87,357 | 6,73,073 ₹6,73,073 |
| 4.00 | Material and labour earthing with copper plate 60×60cm ×3.15mm thick electrode and 20×3mm copper strip as earthing lead, buried directly in ground to a depth not less than 2.25 mtr deep below normal ground level with top edge of the earth plate not less than 1.5 mtr deep below normal ground level connected to20×3mm copper strip as earthing lead by means of nuts, bolts and washers of steel after welding of GI strip to earth electrode to the full length of earth plate, GI medium grade pipe 40 mm bore protection pipe upto test point, 20mm dia GI light grade watering pipe with funnel and wire mesh, RCC pit cover of size 300x300x40mm reinforced with XPM having weight not less than 4Kg/sqmm including 6mm thick MS bar handle made to shape, PCC pit with 1:3:6 type C1 with angle iron frame made of angle iron of size 40x40x4mm, adequate qty of charcoal dust and salt layers all around the earth plate, excavation , earth work in any type of soil, removal of excavated soil and returning filling in all as required at site complete all as specified in plate No 3 of SSR Part-I and all as specified or indicated including testing on completion.
Note :- Rates inclusive of necessary excavation in any type of soil, earth work, PCC pit, RCC cover, funnel with watering pipe,Copper earth strip upto 7.5 m long for connecting to test point etc. all as required at site for complete earthing and dismantling old defective earthpit. | 4 | Each | 24,900 ₹99,600 Lowest | 28,900 ₹1,15,600 | 26,000 ₹1,04,000 | 25,700 ₹1,02,800 | 24,950 ₹99,800 |
| 5.00 | Taking down old unserviceable LT XLPE/PVC insulated 3.5/4 core cable of size 300 to 500 Sqmm complete all as specified and as directed by Engineer in Charge. | 42 | RM | 75 ₹3,150 Lowest | 80 ₹3,360 | 25,000 ₹10,50,000 | 550 ₹23,100 | 100 ₹4,200 |
| 6.00 | Supply, install, testing and commissioning of Sandwich type (Copper + tin plated throughout length), aluminium busway (3L+N+PE), with multi layer polyester film class-F insulation, 100% N, minimum 80kA for 1 sec and 12KV impulse withstand, enclosure as Integral Earth in GI, with IP-55, bus duct shall be made out of min 1.5 mm thick galvanised sheet steel enclosure (C-Ribbed housing in min 1.5 mm thick) with IP-55 and powder coated painted with RAL 7035 or as per OEM design , minimum Temp rise: 55 deg. over ambient of 40 deg, rated insulation & operating voltage1000V of minimum rating 1600 Amps with IP 55 protection straight run with or without outlets complete all as specified and directed by Engineer-in-Charge.
Note : The rate inclusive of Edgewise Hanger (suspension brackets) and angle iron supports wherever required as per OEM design for supporting busduct. Contractor shall submit GA drawing/specification for approval of GE before placing order. | 12 | RM | 23,700 ₹2,84,400 | 24,500 ₹2,94,000 | 250 ₹3,000 Lowest | 12,000 ₹1,44,000 | 32,000 ₹3,84,000 |
| 7.00 | Supply only the 90 Degree (Elbow) special for Sl item No 6.00 above complete all as specified and directed by Engineer-in-Charge. | 1 | Each | 12,400 ₹12,400 Lowest | 13,900 ₹13,900 | 12,600 ₹12,600 | - | 32,000 ₹32,000 |
| 8.00 | Supply only the Flange End special for Sl item No 6.00 above but complete all as specified and directed by Engineer-in-Charge. | 1 | Each | 23,000 ₹23,000 Lowest | 24,500 ₹24,500 | 24,000 ₹24,000 | - | 32,000 ₹32,000 |
| 9.00 | Supply only the Copper flexible (Braided) special for Srl item no 5 here-in-before complete all as specified and directed by Engineer-in-Charge. | 1 | Each | 63,900 ₹63,900 | 65,000 ₹65,000 | 71,000 ₹71,000 | - | 40,000 ₹40,000 Lowest |
| 10.00 | Supply only the Adapter Boxes/Bellows for DG/transformer/LT panel for Srl item no 5 here-in-before complete all as specified and directed by Engineer-in-Charge. | 1 | Each | 71,000 ₹71,000 | 74,500 ₹74,500 | 7,500 ₹7,500 Lowest | - | 40,000 ₹40,000 |
Tender Value
₹47 L
EMD Value
₹94,000
Closing Date
15 Jul 2024, 6:00 pmClosed
GE Minniebay
GE, Minniebay, Junglighat (PO), Port Blair -744103
SPECIAL REPAIR AND REPLACEMENT OF OLD DEFECTIVE CONVENTIONAL CONTROL LT PANELS OF POWER GENERATION SYSTEM WITH NEW MICROPROCESSOR BASED CONTROL PANELS AND OTHER CONNECTED WORKS AT MAIN POWER HOUSE UNDER GE MINNIEBAY, PORT BLAIR
2024_MES_647290_2
8383/E8
Open Tender
Civil Works
Item Rate
180 days
GE Minniebay, Port Blair
Please refer Tender documents.
10 documents required · 10 mandatory
₹500
GE Minniebay
₹94,000
Yes
23 Aug 2025
25 Jun 2024
17 Jul 2024
25 Jun 2024
15 Jul 2024
2 Jul 2024
Amount
Dismantling old defective conventional control LT panels of POWER generation system and Supply, installing, testing and commissioning of microprocessor based LT feeder pillar box factory made cubical indoor type, fabricated out of 2.00 mm thick CRCA sheet with angle iron frame/channel made of suitable size at vertical corners & base of Panel board floor mounted, dust and vermin proof, suitable for voltage 415 V 3 Phase 4 wire weather proof, with IP- 43 protection, with separate hinge door for each compartment with locking arrangement, with back door common openable (Screwed), grouted in PCC (1:2:4) type B1 complete including painting with two coats of epoxy powder paint over a coat of primer after under going a rigorous metal treatment process involving alkaline degreasing, descaling in dilute sulphuric acid or any other acid and phosphate and with aluminium busbar (TPN+E), suitable double compression copper cable glands all as specified and directed by Engineer-in-Charge and including provn of the following:- Note: The panel shall be of similar CPRI type tested panel and quoted rate inclusive of PCC foundation and panelised/compartmental for easy assembling at site. i) Aluminium Bus bar 5000A- mounted on porcelain insulator - 01 Set (Set of 4 Nos) with PVC sleeve insulation and copper earth strip of size 50x6 mm. ii) Microprocessor based Synchronization Controller - 3200XT Make : Woodward - 3 Nos. iii) 1250A, 4P, EDO ACB, with UV & Microprocessor based for Incoming L&T / Schnieder - 3 Nos. iv) 1250A, 4P, MDO ACB, with Microprocessor based for Load L&T / Schnieder - 2 Nos & 1600A, 4P, MDO ACB, with Microprocessor based for Load L&T / Schnieder - 1 Nos.
Dismantling old defective conventional controller panel and Supply, installing, testing and commissioning of microprocessor based LT feeder pillar controller box factory made cubical indoor type, fabricated out of 2.00 mm thick CRCA sheet with angle iron frame/channel made of suitable size at vertical corners & base of Panel board floor mounted, dust and vermine proof, suitable for voltage 415 V 3 Phase 4 wire weather proof, with IP- 43 protection, with separate hinge door for each compartment with locking arrangement, with back door common openable (Screwed), grouted in PCC (1:2:4) type B1 complete including painting with two coats of epoxy powder paint over a coat of primer after under going a rigorous metal treatment process involving alkaline degreasing, descaling in dilute sulphuric acid or any other acid and phosphate and with copper control wiring, suitable double compression copper cable glands and including provn of the following:- Note: The panel shall be of similar CPRI type tested panel and quoted rate inclusive of PCC foundation and panelised/compartmental for easy assembling at site. a) Cummins Governor Cord – 1 No b) Stamford AS440 AVR – 1 No c) Deep-Sea 7320 Engine Controller – 1 No. d) 2mm Thick CRCA sheet Panel with necessary auxiliaries, Relay cord, Emergency Stop button, Control Supply on/off button Etc, e) complete harness wiring
Material and labour earthing with copper plate 60×60cm ×3.15mm thick electrode and 20×3mm copper strip as earthing lead, buried directly in ground to a depth not less than 2.25 mtr deep below normal ground level with top edge of the earth plate not less than 1.5 mtr deep below normal ground level connected to20×3mm copper strip as earthing lead by means of nuts, bolts and washers of steel after welding of GI strip to earth electrode to the full length of earth plate, GI medium grade pipe 40 mm bore protection pipe upto test point, 20mm dia GI light grade watering pipe with funnel and wire mesh, RCC pit cover of size 300x300x40mm reinforced with XPM having weight not less than 4Kg/sqmm including 6mm thick MS bar handle made to shape, PCC pit with 1:3:6 type C1 with angle iron frame made of angle iron of size 40x40x4mm, adequate qty of charcoal dust and salt layers all around the earth plate, excavation , earth work in any type of soil, removal of excavated soil and returning filling in all as required at site complete all as specified in plate No 3 of SSR Part-I and all as specified or indicated including testing on completion. Note :- Rates inclusive of necessary excavation in any type of soil, earth work, PCC pit, RCC cover, funnel with watering pipe,Copper earth strip upto 7.5 m long for connecting to test point etc. all as required at site for complete earthing and dismantling old defective earthpit.
Taking down old unserviceable LT XLPE/PVC insulated 3.5/4 core cable of size 300 to 500 Sqmm complete all as specified and as directed by Engineer in Charge.
Supply, install, testing and commissioning of Sandwich type (Copper + tin plated throughout length), aluminium busway (3L+N+PE), with multi layer polyester film class-F insulation, 100% N, minimum 80kA for 1 sec and 12KV impulse withstand, enclosure as Integral Earth in GI, with IP-55, bus duct shall be made out of min 1.5 mm thick galvanised sheet steel enclosure (C-Ribbed housing in min 1.5 mm thick) with IP-55 and powder coated painted with RAL 7035 or as per OEM design , minimum Temp rise: 55 deg. over ambient of 40 deg, rated insulation & operating voltage1000V of minimum rating 1600 Amps with IP 55 protection straight run with or without outlets complete all as specified and directed by Engineer-in-Charge. Note : The rate inclusive of Edgewise Hanger (suspension brackets) and angle iron supports wherever required as per OEM design for supporting busduct. Contractor shall submit GA drawing/specification for approval of GE before placing order.
Supply only the 90 Degree (Elbow) special for Sl item No 6.00 above complete all as specified and directed by Engineer-in-Charge.
Supply only the Flange End special for Sl item No 6.00 above but complete all as specified and directed by Engineer-in-Charge.
Supply only the Copper flexible (Braided) special for Srl item no 5 here-in-before complete all as specified and directed by Engineer-in-Charge.
Supply only the Adapter Boxes/Bellows for DG/transformer/LT panel for Srl item no 5 here-in-before complete all as specified and directed by Engineer-in-Charge.
Supply, lay, connect, test and commission cable LT 1100 volts heavy duty XLPE insulated armoured aluminium conductors, in trenches/ducts on angle iron supports including glanding, crimping and connecting up of size 3.5 Core x 500 sqmm complete all as specified and as directed. Note: Cable to be laid in existing cable ducts with proper angle iron supports/clamps wherever required with LT end kit heat shrinkable joints complete all as specified and directed by Engineer-in-Charge.
Bharat Udyog
ICON AGENCIES
NAVJEEVAN ENTERPRISES
M/S. RUDRA ENTERPRISES
Bidder Name
Bharat Udyog
stage.html
html • 0.05 MB
tech_bid_open.pdf
tech_eval.pdf
fin_bid_open.pdf
boq_comp_chart.xlsx
xlsx
fin_eval.pdf
aoc.pdf
Tap a document below to read it instantly. You can also download everything as a ZIP if you prefer.
details.html
html • 0.03 MB
Download all tender documents and submit your bid
Disclaimer: TenderKart has made every reasonable effort to ensure that the information on this page is accurate and authentic, however it cannot be held liable for any third-party claims or losses or any damages. TenderKart makes no warranty, expressed or implied, as to the results obtained from the use of this information. If you notice any error or omission, please let us know at .