SPL REPAIR TO ORS QTRS OF AN ENGR REGT AND PROVN OF HARD STANDING CEMENTED VEH SERVICING RAMP AND INSP PIT NEAR URO UNDER AGE B/R-II OF GE (N) MAMUN

Taking down chowkhats or frames with shutters (without taking off shutters from the frames) n.exc 1.50 sqm each complete all as specified and directed.

Taking down chowkhats or frames with shutters (without taking off shutters from the frames) exceeding 1.5 Sqm and n.exc 4 Sqm each complete all as specified and directed.

Taking down shutters of any description exc 1 Sqm but n exc 2 Sqm each complete all as specified and directed.

Demolition of brick work built in cement mortar including all quoins, arches, pillars etc but excluding ashlar facings dressed stonework and pre cast concrete articles and removal of debris/rubbish off the premises etc complete all as specified and directed.

Taking down cement plaster on brick walls or stone walls of any description etc including raking out joints, hacking for key, scrubbing down with water etc, rubbish off the premises complete all as specified and directed.

Demolition of cement concrete unreinforced of any description and in any position not specifically provided and removal of rubbish beyond MOD land complete all as specified and directed.

Demolition of cement concrete (reinforced - reinforcement cut as required to facilitate demolition) Roofs, Floors (other than ground floor), beams staricase, landing, chajja and similar suspended work complete all as specified and directed

Taking up or down steel water tubing and connections including cleaning for refixing of pipe 20mm bore dia all as specified and directed.

All as per item No 8 here above but 15 mm bore

Taking down eaves gutters and rainwater pipes (any size or pattern), including all fittings, heads, shoes, bends, swan-necks, etc complete all as specified and directed.

Excavation in trenches in any type of soil not exceeding 1.5 m wide and n.exc. 1.5 m deep and getting out for laying of cables , foundation flling of poles or stays or for shafts, well, cesspits, manholes, pier holes and complete all as specified and directed.

All as per item No 11 above but exceeding 1.5 m wide and n.exc. 3m deep, complete all as specified and directed.

Returning filling, in including spreading , levelling, watering and well ramming in layers not exc 25 cm each complete all as specified and directed.

Removing excavated material to a distance n exc 50m and depositing where directed at a level n exc 1.5m above the starting point complete all as specified and directed.

S&F pressed steel frames for doors/windows of size size 125x60 mm (1.25mm thick MS sheet) with one or more rebates including necessary fixing lugs, hinges, lock strike plate etc, duly filling of cement concrete 1:3:6 type C-0 (using 12.50 mm graded crushed stone aggregate) to back of chowkhats and two coats of synthentic enamel paint complete all as specified and directed.

S&F pressed steel frames for doors/windows of size size 105x60 mm (1.25mm thick MS sheet) with one or more rebates including necessary fixing lugs, hinges, lock strike plate etc, duly filling of cement concrete 1:3:6 type C-0 (using 12.50 mm graded crushed stone aggregate) to back of chowkhats and two coats of synthentic enamel paint complete all as specified and directed.

S&F for MS angle for cupboard frames with one or more rebates including necessary fixing lugs hinges, locks stike plate etc (thickness shall be 3.00mm) and making good the wall with plaster in CM 1:6 complete all as specified and directed.

S&F Factory made single extruded WPC (Wood Polymer Composite) solid door/ window/Ceosetory windows & other Frames/Chowkhat prefinished with UV coating of size 50x100 mm (duble rebate) comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/ cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2, modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with properties of being termite/borer proof, water/ moisture proof and fire retardant, fixed in position with and including MS hold fast/lugs/SS dash fasteners of required dia and length complete all as specified and directed. Note: (i) For WPC solid door/window frames minus 5mm tolerance in dimension i.e. depth and width of profile shall be acceptable. (ii) Variation in profile dimensions on plus side shall be acceptable but no extra payment on this account shall be made complete all as specified and directed.

35mm thick, Flush shutters soild core construction with block boarde core and plywood face panels, commercial type on both sides face is covered with decorative face veneer with lipping/frame to match complete all as specified and as directed.

S&F 2nd class hard wood 35mm thick glazed and skeleton door shutters factory made, open rebated and prepared to receive glass or gauge etc with rounded, chamfered or mitred sash bars edges of framing plain chamfered or rounded fitted with cut and mitred beads and fitted to chowkats for securing glass/gauge, size of stiles rails and other parts as per section 8 clause 8.20 (a) of SSR Part-I (larger size to be provided) including two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and directed

Factory made single extruded WPC (Wood Polymer Composite) solid decorative type flush door shutter with CNC cutting of 35mm size prefinished with UV coating comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant. WPC to be laminated with PVC foil minimum 14 microns thick of approved design pasted with hot melt adhesive on both faces of shutter and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, complete all as specified and directed. (Note: stainless steel butt hinges and necessary S S screws shall be paid separately).

S&F 18 mm thick HDHMR ( high density high moisture resistance) one side colour laminated as in kitchen cabinet, bed room cup board ward robe, sink/WHB Vanity and like fixed with suitable nails including fixed with suitable edging tape screw to fix with steel/wooden frame complete all as specified and directed.

S&F 05 mm thick HDHMR ( high density high moisture resistance) board as in kitchen cabinet, bed room cup board ward robe and like fixed with suitable nails including fixed with suitable edging tape screw to fix with steel/wooden frame complete all as specified and directed.

S&F Box type Steel windows and ventilators comprised of tubular frame and shutters made out of 1.25mm thick MS steel tube factory made with double side shutters wire gauged shutter & glass glazed shutter (wire mesh and glass panes shall be measured and paid separately) with side hung shutters with steel handle and steel peg stay dovetailed or welded including 2 Nos tower bolts 150mm long for each leaf and 8mm square bar grills at spacing as shown on drg welded to FI frame work, including other fittings, hinges, handles, tarred hold fasts, PCC blocks (1:2:4 type 12.50mm graded crushed stone aggregate) applying two coat of synthetic enamel paint over a shop coat of red oxide primer etc. all as shown on drg No CEPZ /TD-354/09 sheet 1/3 to 3/3 complete all as specified and directed.

M&L for preparation old steel or iron surfaces of any description over 10 cm width or girth and applying two coat of synthetic enamel paint complete all as specified and as directed.

S&F in repair 100mm size stainless steel bright finish handle as approvged by GE, fixed with nut and bolt complete all as specified and directed.

S&F in repair Magnetic catcher (as per sample) for shutter of approved pattern fitted with suitable screws complete all as specified and directed.

Hacking out old broken glass ( any thickness , size, quality, or description) from metal frame glazed with putty or fixed with beads/clips, rubbish off the premises complete all as specified and directed.

S&F 3 mm thick sheet glass ordinary quality and glazing with oil putty or fixed with bead / glazing pins in squares size n.exc 0.5 sqm in each pane all as specified and directed.

S&F 100 mm size butt hinges (as per sample) medium weight, cold rolled mild steel complete all as specified and directed.

S&F 300 mm long aluminium alloy, sliding door bolt with hasp & staple (bolt type) and fixing clips of sheet cast or extruded section and fixing bolts and sliding bolts complete all as specified and directed.

S&F aluminium anodized barrel tower bolts 200 mm of extruded section (as per sample) fixed complete all as specified and directed.

S&F 150 mm size aluminium alloy handles, febricated type extruded section (as per sample), complete all as specified and directed.

S&F 300mm, ordinary rat tail door springs for door closer, complete all as specified and directed.

Brick work with fly ash bricks (Old Size bricks) straight or curved on plan exc 6 mtr mean radius built in CM 1:6 complete all as specified and directed.

M&L for Rendering 10mm thick on fair faces of brick work, concrete sruface in cement mortar (1:6), finished even and smooth without using extra cement complete all as specified and directed.

M&L for Rendering 5mm thick cement plaster on fair faces of brick work, concrete sruface in cement mortar (1:3) as in ceiling finished even and smooth without using extra cement complete all as specified and directed.

M&L for rendering 15 mm thick cemet plaster on fair faces of brick work or concrte surfaces in CM 1:4 in two layers (5mm finishing layer over 10mm base layer) finished even and surface without using extra cement with WPC over finishing layer complete all as specified and directed. Note: WPC shall be measured and paid seperately)

M&L for rendering 10 mm thick in CM 1:3 in fascia / edging / ceiling of Chajjas, roof projections, drainge etc including taking out peeled off plaster/ concrete and making the edges in line, in true shape and finishing the surface without using extra cement complete all as specified and directed.

M&L for preparation of new plastered surface of external wall and chajjas, making surface smooth using sand paper, priming the surface with alkali resistance primer paint for external surface, applying one coat of external wall care putty and two coats of exterior emulsion (weather coat) paint complete all as specified & directed.

M&L for preparation of new plastered surface of external wall by applying 2mm thick wall care putty and making the surfaace smooth applying two coats of distemper oil emulsion over a coat of primer of new surface complete all as specified & directed.

M&L for three coats of white wash on surface of wall including preparation of new plastered surface complete all as specified and as directed.

M&L two coat of white wash on surface of ceiling including preparation of new plastered surface complete all as specified & directed

PCC type C-1, 1:3:6 (using 20mm graded crushed stone aggregate) as in plinth protection 75mm thick laid in slope finished even and fair including making joints not more than 2.5 m (or as directed) and at corner, filled with bitumen 85/25 and sand in ratio 1:2 by weight complete all as specified and directed.

M&L for non skid ceramic coloured tiles 7 to 8 mm thick area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm in floor, skirting/dado or verticle surface etc set and jointed (joint free) in neat cement slurry and pointed in coloured cement over 15mm thick screed bed or bedding layer of mortar in CM 1:4 inculidng dismantling floor, hearth or walls tilling and terrazo topping including cement mortar bedding ( but not backing), rubish off the premises, complete all as specified and directed.

M&L for glazed ceramic coloured tiles in vertical surface 600x300x7mm thick set and jointed in neat cement slurry and pointed in white or coloured cement to match over 10mm thick screed bed or bedding layer of mortar in CM 1:4 including dismantling floor, hearth or walls tilling and terrazo topping including cement mortar bedding ( but not backing), rubish off the premises complete all as specified and directed.

M&L green Marble work 18-20mm thick (table rubbed and polished) in cooking plateform, window cill, steps, stair case trade & riser etc in 15 mm thick cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with marble shade of Bhaislana Zebra complete all as specified & directed.

M&L for Roughening surfaces of old concrete floor by picking, sweeping clean and washing down with water to remove dust, etc., Brushing neat cement slurry with 3.0kg of cement per sq. meter complete all as specified and directed

M&L for Round chamfering to the edges of marble/granite slabs not exc 15 mm wide complete all as specified and directed.

Refixing of old steel tubing 15 mm medium grade galvanized ISI marked with new all fittings short pieces and fixed complete to walls, floor etc complete all as specified and directed.

M&L for cutting chases, pinning in brick work, making good to facing where required, pointing in CM 1:3, cutting n.exc. 10cm in girth complete all as specified and directed.

S&F 20mm bore tubes medium grade galvanized ISI marked with all fittings, short pieces and fixed to walls, floor, ceiling etc complete all as specified and directed.

Refixing of old steel tubing 20 mm medium grade galvanized ISI marked with new all fittings short pieces and fixed complete to walls, floor etc complete all as specified and directed.

S&F 15mm bore tubes medium grade galvanized ISI marked with all fittings, short pieces and fixed to walls, floor, ceiling etc complete all as specified and directed.

S&F in repair 15mm bore dia angle valve / stop valve cast copper alloy capston head chromium plated (as per sample), fancy type ISI marked with crutch or butter fly handles screwed down, screwed for iron pipe complete all as specified and directed.

S&F Stop valve concealed cast copper alloy (ISI Markd) fancy type, chromium plated with long shank and cup (concealed type) screwed down high pressure with crutch lever handle screwed both ends for iron pipe 15mm bore dia fixed in repair, complete all as specified and directed.

S&F in repair 15mm bore dia Bib taps, cast copper alloy, chromium plated fancy type ISI marked (as per sample) with crutch or butter fly handles, screwed down, screwed for iron pipe complete all as specified and directed.

S&F in repair towel rail, brass, CP 600 mm long complete all as specified and directed.

S & F in repair brass CP Shower rose with or without swivel joints, (any size) including fixing to steel pipe or union complete all as specified & directed.

S&F in repair Vitreous China squatting pan of orissa pattern, size 580x440mm white with CI ‘P’ or ‘S’ trap, front or back inlet and foot rests, any pattern (including fixing of flush pipe) including provision of cement concrete bedding, in repair complete all as specified & directed.

S & F in repair vitreous china, wash hand basin, white, flat back, of size 550mmx400mm with brackets including cutting for and pinning in ends of brackets, complete all as specified or erecting stand including 32mm full threaded waste coupling and 32mm PVC waste pipe, complete all as specified and directed.

S&F 15mm bore pillar tap, copper alloy with capstan head, chromium plated screwed down high pressure, with or without lettered hot/cold with long screwed shanks and fly nuts screwed for iron pipe (fixed in repairs), complete all as specified and directed.

S&F in repair Vitreous china wash down water closet pan P trap pedestal pattern, white (excluding supply of flushing cistern and flush pipes, but including fixing thereof), including making connections to trap, and to flush pipe including plastic seat and cover with stainless steel or aluminised hinging device and fixed complete all as specified and directed.

S&F 10 litre capacity PVC valveless, low level, synphonic action type, flushing cistern, with inlet, ball valve, float valve, handle including brackets including 32mm dia PVC flush pipe of suitable size and making necessary connections to water supply pipe line and jointing to WC, complete all as specified and directed.

S&F PVC connections 15mm size with PTMT nuts of length 450mm complete all as specified and directed.

Rotational moulded polyethlene water storage tanks of capacity exc 500 litres three layers (cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR Part I complete including 20mm dia ball brass valve high pressure with polythene float and dismantling of existing RCC/PVC tank of any capacity complete all as specified & directed.

S&F in repair 20 mm size gun metal globe or gate valves with iron wheel head, screwed both end for iron pipe and fixed cast copper chromium plated fancy type alloy ISI marked with crutch or butter fly handles screwed down screwed for iron pipe of 20mm bore complete all as specified and directed.

S&F stainless steel kitchen plate rack of size 750 x 900 mm not less than 1mm thick sheet thickness of approved make fixed with mild steel screw complete all as specified and directed.

S&F kitchen sinks with drainage board made of stainless steel 1mm thick with plugs, washers , PVC waste pipe fixed in repair including waste copling; bedding in cement mortar on to dwarf wall or including fixing cantilever brackets and connecting union to pipe, overall size 915x460mm bowl size 410mm x 330mm x 160mm complete all as specified and directed.

S&F 75mm bore dia PVC (SWR) pipes, single socketed, in any length with rubber ring joints, fixed to walls with clamps, complete all as specified and directed.

S&F 110mm bore dia PVC (SWR) pipes, single socketed, in any length with rubber ring joints, fixed to walls with clamps, complete all as specified and directed.

S&F 110mm bore dia PVC (SWR) bends,any radius (larger bore measured), complete all as specified and directed.

S&F 75mm bore dia PVC (SWR) bends,any radius (larger bore measured), complete all as specified and directed.

S&F 110mm bore dia PVC (SWR) reducers, complete all as specified and directed.

S&F 110mm bore dia PVC (SWR) branch piece, single (single Y) equal or unequal with parrallel branches fitted with oval access doors, complete all as specified and directed.

S&F PVC (SWR) 75mm bore Branch pieces, double (equal or unequal), ordinary or inverted (spigot or socket type) or with parallel branches, fitted with ovel access doors, complete all as specified and directed.

S&F 75mm bore pipe PVC (SWR) vent cowl, complete all as specified and directed.

S&F in PVC floor trap 75mm with grating including jointing to waste pipe fixed in cement concrete 1:2:4 type B-1 with CP grating with or without hole for waste pipe complete all as specified and directed.

M&L for Surface dressing n exc 15 cm deep and getting out in soft/loose soil complete all as specified and directed.

M&L for PCC 1:4:8 type D-2 (using 40mm graded crushed stone aggregate) as in foundation, filling and mass concrete complete all as specified and directed.

M&L for Reinforced cement concrete 1:1.5:3 type A1 using 20mm graded crushed stone aggregate in foundation, including rafts, footings, foundation beams; plinth beams; bases for columns, etc.; basement slabs, under-reamed piles and mass concrete complete all as specified and directed.

M&L for reinforced cement concrete 1:1.5:3 type A1 using 20mm graded crushed stone aggregate as in walls, retaining walls, and the kike any thickness ; above top of footings; including attached pilasters and buttresses complete all as specified & directed.

M&L formwork to sides of rough finished flat surface of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work; vertical or to batter, including flat rough finished surafaces of concrete complete all as specified and directed.

M&L for Hardcore of gauge n exc. 63 mm, deposited, spread and levelled in layers n exc. 15 cm thick, watered and rammed to a true surface complete all as specified and directed.

M&L for 75mm thick PCC 1:2:4 type B-2 (using 40mm graded crushed stone aggregate) as in sub floors, sub bases, floors and pavings etc complete all as specified and directed.

M&L for 100mm thick Cement Concrete 1:2:4 type B2 (40mm graded crushed stone aggregate) as Flooring laid in alternate bays finsihed fair and even without using extra cement complete all as specified and directed.

M&L for 100mm thick PCC 1:3:6 type C-2 using (40mm graded crushed stone aggregate) as in aub floors, sub bases, and paving etc complete all as specified and directed.

M&L for Sand filling under floors or in foundation in layers n exc 25mm thick including watering and consolidation complete all as specified and directed.

M&L for PCC 1:2:4 type B-0 ( using 12.5mm graded crushed stone aggregate) padding as roof , surface finished even and smooth without using extra cement complete all as specified and directed.

M&L 15 mm thick cement plaster in cement mortar 1:4 on fair faces of brick masonary/ concrete surface finished even and smooth without using extra cement omplete all as specified & directed (WPC shall be measured and paid separately)

M&L 20 mm thick cement plaster in cement mortar 1:4 on brick or concrete surface finished even and smooth using WPC liquid of make Dr. Fixit or STP as per manufacturer instruction @ 0.200 ltr in 50 Kg of cement complete all as specified & directed (WPC shall be measured and paid separately)

M&L for preparation of surfaces and apply first coat fiber reinforced elastomatic liquid water proofing membrane formulated with PU hybrid ploymersand reinfoecing acrylic fibers with sun reflective index(SRI) of 100-110 having maximumelongation of 350% tensile strength od 2.9 Mpa and shall have crack bridging ability upto 2.5mm and shall resist 10 bars of hydrostatic presure and reduce surface temprerature upto 10 degree celsius with 33% ditution of priming coat. Laying of fiber mesh of 0.3mm thickness weave in leno pattern having 45 grm/sqm and pastinf it properly with overlaping of 50mm and allow it to dry, Apply second coat of undiluted coat @ 0.45 ltr/ Sqm . Apply third and final coat undiluted @ 0.45 ltr/sqm complete application to be done by the manufacture of authorised applicator complete all as specified and directed.

Supply only liquid water proofing compound complete all as specified and directed.

Supply only Universal Repair Ploymer (URP), a modified styrene butadiene latex used as bonding agent, for water proofing and damaged cencrete as coating mortar, complete all as specified and directed (Make : Pidilite)

S&F TMT bars 8mm to 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with the including mild steel wire (annealed) not less than 0.9mm dia or securing with clips all as specified & directed.

M&L for 60mm thickness M-35 grade Machine pressed precast concrete factory made paver block confirming to IS-15658-2006 (topping thickness not less than 5mm thick with white cement and colour pigment non fadable epoxy coating) complete all as specified & directed.

Forming contraction (dummy) joints 65mm deep and 10mm wide filled with sealing compound Gde 'A"

Forming constuction joints 30mm deep and 10mm wide filled with sealing compound Gde 'A"

Disconnecting electrically, dismantling and taking out old light fittings any type/size and keeping in safe custody for reusing serviceable light fittings complete all as specified and directed.

Fixing only light fittings (retrieved under ser item number 101) with making electric connections complete all as specified and directed.

S&F LED Lamp 15 watt suitable for fixing in lamp holder complete all as specified.

S&F distribution board iron clad, double door with IP-43 1K-09 protection suitable for MCCB as incommer and MCB as outgoing 415 Volts 3 phase 50 C/s 4 way, complete with appropriate size copper bus bar and neutral link complete with one MCCB 3 pole 415 V, 63 Amps, 16 KA of the same make as of distribution board, making connection with suitable size thimbles & including cutting chases to wall for fixing DB and making good the disturbed wall surface in CM 1:4 to match the surface as per existing complete all as specified and directed.

S&F PVC round junction box cover not less than 10cm dia, 0.3cm thick incl fixing with suitable size of machine screw complete all as specified and directed.

S&F LED wall security lights of 35 Watt having pressure die cast aluminium housing with system lumens efficacy≥100 lumen/W, IP65 protection, IK07 rating, inbuilt electronic driver with PF>0.95 incl GI bracket of suitable dia bend to shape and fixed to wall by means of clamps or nuts bolts and connecting up with three core twisted flexible copper conductor cable complete all as specified and directed.

S&F MCB SP 240V, 50Hz of rating 6 to 32 Amp, 'B' curve using suitable size copper thimbles complete all as specified and directed.

All as per Ser item No 107 but for size 32/40/63 Amps MCB SPN.

Disconneting & taking down ceiling fan / exhaust fan any type/ cap refixing to the same/other location after replacing rubber reel, fixing bolts and nuts with lock pins, connectors complete all as specified and directed.

Disconneting & taking down geyser any type/capacity complete, refixing to the same/other location with all connected accessories afer cleaning replacing anchor bolts complete all as specified and directed.

Supply, laying and testing insulated XLPE, screened, PVC beded galvansized steel strip or wire armoured, electric cable heavy duty 1100 volts grade with stranded aluminium conductor of size 35 Sqmm 3.5 core complete all as specified and directed.

M&L for sand filling in trenches as cushion to under ground cables 8 cm thick before laying the cable and 15 cm thick when cables are laid and tested complete all as specified and directed. Note: Only punned thickness i.e 18cm shall be measured and paid.

40mm dia GI tubing, light grade with all fitting laid in trenches or fixed on wall/under road/ floor or pole by means of GI/MS clamps, nut bolts and washers complete all as specified and directed.

M&L for Sub class ‘B’ bricks old size laid dry, flat over the cable abutting each other, length of cable equal to width of brick complete all as specified and directed.

Please Enable Macros to View BoQ information