Hot tapping and welding works in MPPL PBPL pipelines

Amount

PANIPAT-PBPL

Supply of Thread -O-Ring 2'', 600# as per technical specifications

Supply of ASTM A 106 GR.B STEEL PIPES 2.375" ODas per technical specifications

Supply of REDUCER RED,CONC,BW,CS,A234,WPB,2X1IN,80X80 as per technical specifications

Supply of 2'' 600# GATE VALVE W/Was per technical specifications

Supply of ASTM A 106 GR.B STEEL PIPES 1.315" OD as per technical specifications

Supply of 1'' 600# GLOBE VALVE F/F as per technical specifications

Supply of 1", WNRF FLANGE, ANSI - 600# as per technical specifications

Supply of Fasteners for Flanges 1" x 600# as per technical specifications

Supply of Bushing 1'' X 1/2'' NPT (F) as per technical specifications

Supply of Supply of epoxy paint as per technical specifications

SERVICES

Removal and restoration of cladding /coating for carryng out welding and tapping work as per scope of work

Welding of weld pad (To be supplied by Owner) for installation of surface mounted RTDs at RCP (under jurisdiction) and station locaions & welding of Parts of Piping for Pressure Transmitter station locations

Inspection of welding by radiographic method at station locations

Inspection of welding by radiographic method at RCP locations

Mobilisation Advance per station

Excavation as per scope of work and technical specifications for depth upto 2.5 m : Earth work in excavation in all kinds of soil except hard rock requiring blasting for foundation trenches, upto any depth including trimming of sides of the trenches, dressing, ramming and levelling the bottom of the trenches correct to level, grade etc. including bailing out of water, if any, filling in sides of foundation trenches, plinth etc. with the excavated earth available and/or depositing the excess earth within station area limits, in layers not exceeding 20 cms. thick, consolidating each deposited layer by ramming, watering, dressing to level and grade , complete in all respects inclusive of cost of all labour, materials, tools, tackles etc. as per drawings, specifications and direction of Site Engineer.

Extra for filling the excavated earth over and above excavation cost

Demolishing P.C.C. work as per scope of work and technical specifications : Demolishing P.C.C. work in existing building structures at all heights and depths using pnuematic tools or as approved by Engineer-in- charge including following all safety requirements, ensuring adequate precaution to the neighbourhood structures & equipment, putting necessary cover , and disposal of unserviceable material within station area limit all complete as directed by Site Engineer.

Excavation as per scope of work and technical specifications for depth above 2.5 m

COMPOSITE

Hot tapping for PT and complete installation of PT as per drawing , scope of work and technical specifications

Brick work with bricks of class designation 50 in cement mortar 1:6 (1 cement : 6 coarse sand) at all heights and depths laid to proper position line, level as per the drawings and specifications including providing necessary scaffolding, staging, raking out of joints, curing etc. complete in all respects inclusive of cost of all labour, materials, tools, tackles etc. as per drawings, specifications and direction of Site Engineer as per technical specifications and tender scope of work

Plastering- CEMENT PLASTER (IN FINE SAND) 1:6 (1 cement: 6 fine sand) : 13.1.2 Providing 15 mm thick plaster to internal & external walls at all heights/depths with cement mortar 1:6 (1 cement :6 fine sand) finished smooth/rough including raking out joints, rounding off and chamfering corners, making drip course moulding, roughening of brick surface, curing for etc. complete as per specifications.

Supplying and placing in position 5 mm thick steel chequred plates over cable ducts, valve pits etc. including provision for lifting arrangements complete in all respects inclusive of cost of all labour, materials, tools, tackles etc. as per drawings, specifications and direction of Site Engineer.

Construction of STAIR- Supplying, fabricating, erecting, placing and fixing in position M.S. structural works using rolled/ built up sections for truss, claddings, bracings, purlins, supporting frames made of joists, tubes, pipes, channels, angles, plates,flats, bars etc. including cutting to required size welding of joints, fixing anchor plates, including bolts, theading, nuts, washers, sleeves etc. including preparation of detailed fabrication drawings & submission to Engineer-in-charge for approval before start of fabrication, supplying & applying painting with two coats of epoxy paint "EPILUX 155 High Build Enamel over a coat of EPILUX 610 Primer of M/s Berger or any other approved equivalent make as per manufacturer’s recommendation, complete in all respects inclusive of cost of all labour, materials, tools, tackles etc. as per drawings, specifications and direction of Site Engineer. (excluding the cost of concrete work).

Supplying and spreading of approved quality,fine, dry /river sand in cable trenches as per drawings, specifi- cations and directions of the Site Engineer, including the cost of all material, transport, load and lift charges, labour,tools etc. complete in all respects.

Painting work including Surface preparation ,etc. as per technical specifications and tender scope of work: Supplying and applying three coats of super acrylic emulsion paint like RANGOLI of Berger or any other approved equivalent brand, of required shade on newly plaster surface including preparation of base surface with putty, two coats of cement primer, scaffolding etc. complete in all respects inclusive of cost of all labour, materials, tools, tackles etc. as per manufacturer’s recommendations, specification and direction of Site Engineer.

Painting works for steel work as per technical specifications and tender scope of work : Providing and applying painting with synthetic enamel paint in two or more coats on new work of approved brand and manufacture to give an even shade including cleaning of surface complete as per specfication and direction of Engineer-in-Charge/Site Engineer.

Providing and laying cement concrete of mix 1:4:8 (1 cement:4 coarse sand :8 graded stone aggregate 40 mm nominal size) for foundation works at all depths including ramming, dewatering & shuttering etc. complete in all respects inclusive of cost of all labour, materials, tools, tackles etc. as per drawings, specifications and direction of Site Engineer.

SUPPLY

Supply of Gaskets 1" SWMG ANSI 600# as per technical specifications

SANGRUR-PBPL -18%

SUPPLY

Supply of Thread -O-Ring 2'', 600# as per technical specifications

Supply of ASTM A 106 GR.B STEEL PIPES 2.375" ODas per technical specifications

Supply of REDUCER RED,CONC,BW,CS,A234,WPB,2X1IN,80X80 as per technical specifications

Supply of 2'' 600# GATE VALVE W/Was per technical specifications

Supply of ASTM A 106 GR.B STEEL PIPES 1.315" OD as per technical specifications

Supply of 1'' 600# GLOBE VALVE F/F as per technical specifications

Supply of 1", WNRF FLANGE, ANSI - 600# as per technical specifications

Supply of Fasteners for Flanges 1" x 600# as per technical specifications

Supply of Bushing 1'' X 1/2'' NPT (F) as per technical specifications

service

Removal and restoration of cladding /coating for carryng out welding and tapping work as per scope of work

Welding of weld pad (To be supplied by Owner) for installation of surface mounted RTDs at RCP (under jurisdiction) and station locaions & welding of Parts of Piping for Pressure Transmitter station locations

Inspection of welding by radiographic method at station locations

Inspection of welding by radiographic method at RCP locations

Mobilisation Advance per station

Excavation as per scope of work and technical specifications for depth upto 2.5 m : Earth work in excavation in all kinds of soil except hard rock requiring blasting for foundation trenches, upto any depth including trimming of sides of the trenches, dressing, ramming and levelling the bottom of the trenches correct to level, grade etc. including bailing out of water, if any, filling in sides of foundation trenches, plinth etc. with the excavated earth available and/or depositing the excess earth within station area limits, in layers not exceeding 20 cms. thick, consolidating each deposited layer by ramming, watering, dressing to level and grade , complete in all respects inclusive of cost of all labour, materials, tools, tackles etc. as per drawings, specifications and direction of Site Engineer.

Extra for filling the excavated earth over and above excavation cost

Demolishing P.C.C. work as per scope of work and technical specifications : Demolishing P.C.C. work in existing building structures at all heights and depths using pnuematic tools or as approved by Engineer-in- charge including following all safety requirements, ensuring adequate precaution to the neighbourhood structures & equipment, putting necessary cover , and disposal of unserviceable material within station area limit all complete as directed by Site Engineer.

Excavation as per scope of work and technical specifications for depth above 2.5 m

COMPOSITE

Hot tapping for PT and complete installation of PT as per drawing , scope of work and technical specifications

Brick work with bricks of class designation 50 in cement mortar 1:6 (1 cement : 6 coarse sand) at all heights and depths laid to proper position line, level as per the drawings and specifications including providing necessary scaffolding, staging, raking out of joints, curing etc. complete in all respects inclusive of cost of all labour, materials, tools, tackles etc. as per drawings, specifications and direction of Site Engineer as per technical specifications and tender scope of work

Plastering- CEMENT PLASTER (IN FINE SAND) 1:6 (1 cement: 6 fine sand) : 13.1.2 Providing 15 mm thick plaster to internal & external walls at all heights/depths with cement mortar 1:6 (1 cement :6 fine sand) finished smooth/rough including raking out joints, rounding off and chamfering corners, making drip course moulding, roughening of brick surface, curing for etc. complete as per specifications.

Supplying and placing in position 5 mm thick steel chequred plates over cable ducts, valve pits etc. including provision for lifting arrangements complete in all respects inclusive of cost of all labour, materials, tools, tackles etc. as per drawings, specifications and direction of Site Engineer.

Construction of STAIR- Supplying, fabricating, erecting, placing and fixing in position M.S. structural works using rolled/ built up sections for truss, claddings, bracings, purlins, supporting frames made of joists, tubes, pipes, channels, angles, plates,flats, bars etc. including cutting to required size welding of joints, fixing anchor plates, including bolts, theading, nuts, washers, sleeves etc. including preparation of detailed fabrication drawings & submission to Engineer-in-charge for approval before start of fabrication, supplying & applying painting with two coats of epoxy paint "EPILUX 155 High Build Enamel over a coat of EPILUX 610 Primer of M/s Berger or any other approved equivalent make as per manufacturer’s recommendation, complete in all respects inclusive of cost of all labour, materials, tools, tackles etc. as per drawings, specifications and direction of Site Engineer. (excluding the cost of concrete work).

Supplying and spreading of approved quality,fine, dry /river sand in cable trenches as per drawings, specifi- cations and directions of the Site Engineer, including the cost of all material, transport, load and lift charges, labour,tools etc. complete in all respects.

Painting work including Surface preparation ,etc. as per technical specifications and tender scope of work: Supplying and applying three coats of super acrylic emulsion paint like RANGOLI of Berger or any other approved equivalent brand, of required shade on newly plaster surface including preparation of base surface with putty, two coats of cement primer, scaffolding etc. complete in all respects inclusive of cost of all labour, materials, tools, tackles etc. as per manufacturer’s recommendations, specification and direction of Site Engineer.

Painting works for steel work as per technical specifications and tender scope of work : Providing and applying painting with synthetic enamel paint in two or more coats on new work of approved brand and manufacture to give an even shade including cleaning of surface complete as per specfication and direction of Engineer-in-Charge/Site Engineer.

Providing and laying cement concrete of mix 1:4:8 (1 cement:4 coarse sand :8 graded stone aggregate 40 mm nominal size) for foundation works at all depths including ramming, dewatering & shuttering etc. complete in all respects inclusive of cost of all labour, materials, tools, tackles etc. as per drawings, specifications and direction of Site Engineer.

Supply

Supply of Supply of epoxy paint as per technical specifications

Supply of Gaskets 1" SWMG ANSI 600# as per technical specifications

BHATINDA-PBPL - 18%

SUPPLY

Supply of Thread -O-Ring 2'', 600# as per technical specifications

Supply of ASTM A 106 GR.B STEEL PIPES 2.375" ODas per technical specifications

Supply of REDUCER RED,CONC,BW,CS,A234,WPB,2X1IN,80X80 as per technical specifications

Supply of 2'' 600# GATE VALVE W/Was per technical specifications

Supply of ASTM A 106 GR.B STEEL PIPES 1.315" OD as per technical specifications

Supply of 1'' 600# GLOBE VALVE F/F as per technical specifications

Supply of 1", WNRF FLANGE, ANSI - 600# as per technical specifications

Supply of Fasteners for Flanges 1" x 600# as per technical specifications

Supply of Bushing 1'' X 1/2'' NPT (F) as per technical specifications

SERVICE

Removal and restoration of cladding /coating for carryng out welding and tapping work as per scope of work

Welding of weld pad (To be supplied by Owner) for installation of surface mounted RTDs at RCP (under jurisdiction) and station locaions & welding of Parts of Piping for Pressure Transmitter station locations

Inspection of welding by radiographic method at station locations

Mobilisation Advance per station

Excavation as per scope of work and technical specifications for depth upto 2.5 m : Earth work in excavation in all kinds of soil except hard rock requiring blasting for foundation trenches, upto any depth including trimming of sides of the trenches, dressing, ramming and levelling the bottom of the trenches correct to level, grade etc. including bailing out of water, if any, filling in sides of foundation trenches, plinth etc. with the excavated earth available and/or depositing the excess earth within station area limits, in layers not exceeding 20 cms. thick, consolidating each deposited layer by ramming, watering, dressing to level and grade , complete in all respects inclusive of cost of all labour, materials, tools, tackles etc. as per drawings, specifications and direction of Site Engineer.

Demolishing P.C.C. work as per scope of work and technical specifications : Demolishing P.C.C. work in existing building structures at all heights and depths using pnuematic tools or as approved by Engineer-in- charge including following all safety requirements, ensuring adequate precaution to the neighbourhood structures & equipment, putting necessary cover , and disposal of unserviceable material within station area limit all complete as directed by Site Engineer.

Excavation as per scope of work and technical specifications for depth above 2.5 m

COMPOSITE

Hot tapping for PT and complete installation of PT as per drawing , scope of work and technical specifications

Brick work with bricks of class designation 50 in cement mortar 1:6 (1 cement : 6 coarse sand) at all heights and depths laid to proper position line, level as per the drawings and specifications including providing necessary scaffolding, staging, raking out of joints, curing etc. complete in all respects inclusive of cost of all labour, materials, tools, tackles etc. as per drawings, specifications and direction of Site Engineer as per technical specifications and tender scope of work

Plastering- CEMENT PLASTER (IN FINE SAND) 1:6 (1 cement: 6 fine sand) : 13.1.2 Providing 15 mm thick plaster to internal & external walls at all heights/depths with cement mortar 1:6 (1 cement :6 fine sand) finished smooth/rough including raking out joints, rounding off and chamfering corners, making drip course moulding, roughening of brick surface, curing for etc. complete as per specifications.

Supplying and placing in position 5 mm thick steel chequred plates over cable ducts, valve pits etc. including provision for lifting arrangements complete in all respects inclusive of cost of all labour, materials, tools, tackles etc. as per drawings, specifications and direction of Site Engineer.

Construction of STAIR- Supplying, fabricating, erecting, placing and fixing in position M.S. structural works using rolled/ built up sections for truss, claddings, bracings, purlins, supporting frames made of joists, tubes, pipes, channels, angles, plates,flats, bars etc. including cutting to required size welding of joints, fixing anchor plates, including bolts, theading, nuts, washers, sleeves etc. including preparation of detailed fabrication drawings & submission to Engineer-in-charge for approval before start of fabrication, supplying & applying painting with two coats of epoxy paint "EPILUX 155 High Build Enamel over a coat of EPILUX 610 Primer of M/s Berger or any other approved equivalent make as per manufacturer’s recommendation, complete in all respects inclusive of cost of all labour, materials, tools, tackles etc. as per drawings, specifications and direction of Site Engineer. (excluding the cost of concrete work).

Supplying and spreading of approved quality,fine, dry /river sand in cable trenches as per drawings, specifi- cations and directions of the Site Engineer, including the cost of all material, transport, load and lift charges, labour,tools etc. complete in all respects.

Painting work including Surface preparation ,etc. as per technical specifications and tender scope of work: Supplying and applying three coats of super acrylic emulsion paint like RANGOLI of Berger or any other approved equivalent brand, of required shade on newly plaster surface including preparation of base surface with putty, two coats of cement primer, scaffolding etc. complete in all respects inclusive of cost of all labour, materials, tools, tackles etc. as per manufacturer’s recommendations, specification and direction of Site Engineer.

Painting works for steel work as per technical specifications and tender scope of work : Providing and applying painting with synthetic enamel paint in two or more coats on new work of approved brand and manufacture to give an even shade including cleaning of surface complete as per specfication and direction of Engineer-in-Charge/Site Engineer.

Providing and laying cement concrete of mix 1:4:8 (1 cement:4 coarse sand :8 graded stone aggregate 40 mm nominal size) for foundation works at all depths including ramming, dewatering & shuttering etc. complete in all respects inclusive of cost of all labour, materials, tools, tackles etc. as per drawings, specifications and direction of Site Engineer.

SUPPLY

Supply of Supply of epoxy paint as per technical specifications

Supply of Gaskets 1" SWMG ANSI 600# as per technical specifications

REWARI-MPPL

SUPPLY

Supply of Thread -O-Ring 2'', 600# as per technical specifications

Supply of ASTM A 106 GR.B STEEL PIPES 2.375" ODas per technical specifications

Supply of REDUCER RED,CONC,BW,CS,A234,WPB,2X1IN,80X80 as per technical specifications

Supply of 2'' 600# GATE VALVE W/Was per technical specifications

Supply of ASTM A 106 GR.B STEEL PIPES 1.315" OD as per technical specifications

Supply of 1'' 600# GLOBE VALVE F/F as per technical specifications

Supply of 1", WNRF FLANGE, ANSI - 600# as per technical specifications

Supply of Fasteners for Flanges 1" x 600# as per technical specifications

Supply of Bushing 1'' X 1/2'' NPT (F) as per technical specifications

Supply of Supply of epoxy paint as per technical specifications

SERVICE

Removal and restoration of cladding /coating for carryng out welding and tapping work as per scope of work

Welding of weld pad (To be supplied by Owner) for installation of surface mounted RTDs at RCP (under jurisdiction) and station locaions & welding of Parts of Piping for Pressure Transmitter station locations

Inspection of welding by radiographic method at station locations

Inspection of welding by radiographic method at RCP locations

Mobilisation Advance per station

Excavation as per scope of work and technical specifications for depth upto 2.5 m : Earth work in excavation in all kinds of soil except hard rock requiring blasting for foundation trenches, upto any depth including trimming of sides of the trenches, dressing, ramming and levelling the bottom of the trenches correct to level, grade etc. including bailing out of water, if any, filling in sides of foundation trenches, plinth etc. with the excavated earth available and/or depositing the excess earth within station area limits, in layers not exceeding 20 cms. thick, consolidating each deposited layer by ramming, watering, dressing to level and grade , complete in all respects inclusive of cost of all labour, materials, tools, tackles etc. as per drawings, specifications and direction of Site Engineer.

Extra for filling the excavated earth over and above excavation cost

Demolishing P.C.C. work as per scope of work and technical specifications : Demolishing P.C.C. work in existing building structures at all heights and depths using pnuematic tools or as approved by Engineer-in- charge including following all safety requirements, ensuring adequate precaution to the neighbourhood structures & equipment, putting necessary cover , and disposal of unserviceable material within station area limit all complete as directed by Site Engineer.

Excavation as per scope of work and technical specifications for depth above 2.5 m

COMPOSITE

Hot tapping for PT and complete installation of PT as per drawing , scope of work and technical specifications

Brick work with bricks of class designation 50 in cement mortar 1:6 (1 cement : 6 coarse sand) at all heights and depths laid to proper position line, level as per the drawings and specifications including providing necessary scaffolding, staging, raking out of joints, curing etc. complete in all respects inclusive of cost of all labour, materials, tools, tackles etc. as per drawings, specifications and direction of Site Engineer as per technical specifications and tender scope of work

Plastering- CEMENT PLASTER (IN FINE SAND) 1:6 (1 cement: 6 fine sand) : 13.1.2 Providing 15 mm thick plaster to internal & external walls at all heights/depths with cement mortar 1:6 (1 cement :6 fine sand) finished smooth/rough including raking out joints, rounding off and chamfering corners, making drip course moulding, roughening of brick surface, curing for etc. complete as per specifications.

Supplying and placing in position 5 mm thick steel chequred plates over cable ducts, valve pits etc. including provision for lifting arrangements complete in all respects inclusive of cost of all labour, materials, tools, tackles etc. as per drawings, specifications and direction of Site Engineer.

Construction of STAIR- Supplying, fabricating, erecting, placing and fixing in position M.S. structural works using rolled/ built up sections for truss, claddings, bracings, purlins, supporting frames made of joists, tubes, pipes, channels, angles, plates,flats, bars etc. including cutting to required size welding of joints, fixing anchor plates, including bolts, theading, nuts, washers, sleeves etc. including preparation of detailed fabrication drawings & submission to Engineer-in-charge for approval before start of fabrication, supplying & applying painting with two coats of epoxy paint "EPILUX 155 High Build Enamel over a coat of EPILUX 610 Primer of M/s Berger or any other approved equivalent make as per manufacturer’s recommendation, complete in all respects inclusive of cost of all labour, materials, tools, tackles etc. as per drawings, specifications and direction of Site Engineer. (excluding the cost of concrete work).

Supplying and spreading of approved quality,fine, dry /river sand in cable trenches as per drawings, specifi- cations and directions of the Site Engineer, including the cost of all material, transport, load and lift charges, labour,tools etc. complete in all respects.

Painting work including Surface preparation ,etc. as per technical specifications and tender scope of work: Supplying and applying three coats of super acrylic emulsion paint like RANGOLI of Berger or any other approved equivalent brand, of required shade on newly plaster surface including preparation of base surface with putty, two coats of cement primer, scaffolding etc. complete in all respects inclusive of cost of all labour, materials, tools, tackles etc. as per manufacturer’s recommendations, specification and direction of Site Engineer.

Painting works for steel work as per technical specifications and tender scope of work : Providing and applying painting with synthetic enamel paint in two or more coats on new work of approved brand and manufacture to give an even shade including cleaning of surface complete as per specfication and direction of Engineer-in-Charge/Site Engineer.

Providing and laying cement concrete of mix 1:4:8 (1 cement:4 coarse sand :8 graded stone aggregate 40 mm nominal size) for foundation works at all depths including ramming, dewatering & shuttering etc. complete in all respects inclusive of cost of all labour, materials, tools, tackles etc. as per drawings, specifications and direction of Site Engineer.

Supply

Supply of Bushing 1'' X 1/2'' NPT (F) as per technical specifications

Supply of Gaskets 1" SWMG ANSI 600# as per technical specifications

PANIPAT-MPPL

SUPPLY

Supply of Thread -O-Ring 2'', 600# as per technical specifications

Supply of ASTM A 106 GR.B STEEL PIPES 2.375" ODas per technical specifications

Supply of REDUCER RED,CONC,BW,CS,A234,WPB,2X1IN,80X80 as per technical specifications

Supply of 2'' 600# GATE VALVE W/Was per technical specifications

Supply of ASTM A 106 GR.B STEEL PIPES 1.315" OD as per technical specifications

Supply of 1'' 600# GLOBE VALVE F/F as per technical specifications

Supply of 1", WNRF FLANGE, ANSI - 600# as per technical specifications

Supply of Fasteners for Flanges 1" x 600# as per technical specifications

Supply of Bushing 1'' X 1/2'' NPT (F) as per technical specifications

Supply of Supply of epoxy paint as per technical specifications

SERVICE

Removal and restoration of cladding /coating for carryng out welding and tapping work as per scope of work

Welding of weld pad (To be supplied by Owner) for installation of surface mounted RTDs at RCP (under jurisdiction) and station locaions & welding of Parts of Piping for Pressure Transmitter station locations

Inspection of welding by radiographic method at station locations

Inspection of welding by radiographic method at RCP locations

Mobilisation Advance per station

Excavation as per scope of work and technical specifications for depth upto 2.5 m : Earth work in excavation in all kinds of soil except hard rock requiring blasting for foundation trenches, upto any depth including trimming of sides of the trenches, dressing, ramming and levelling the bottom of the trenches correct to level, grade etc. including bailing out of water, if any, filling in sides of foundation trenches, plinth etc. with the excavated earth available and/or depositing the excess earth within station area limits, in layers not exceeding 20 cms. thick, consolidating each deposited layer by ramming, watering, dressing to level and grade , complete in all respects inclusive of cost of all labour, materials, tools, tackles etc. as per drawings, specifications and direction of Site Engineer.

Extra for filling the excavated earth over and above excavation cost

Demolishing P.C.C. work as per scope of work and technical specifications : Demolishing P.C.C. work in existing building structures at all heights and depths using pnuematic tools or as approved by Engineer-in- charge including following all safety requirements, ensuring adequate precaution to the neighbourhood structures & equipment, putting necessary cover , and disposal of unserviceable material within station area limit all complete as directed by Site Engineer.

COMPOSITE

Hot tapping for PT and complete installation of PT as per drawing , scope of work and technical specifications

Brick work with bricks of class designation 50 in cement mortar 1:6 (1 cement : 6 coarse sand) at all heights and depths laid to proper position line, level as per the drawings and specifications including providing necessary scaffolding, staging, raking out of joints, curing etc. complete in all respects inclusive of cost of all labour, materials, tools, tackles etc. as per drawings, specifications and direction of Site Engineer as per technical specifications and tender scope of work

Plastering- CEMENT PLASTER (IN FINE SAND) 1:6 (1 cement: 6 fine sand) : 13.1.2 Providing 15 mm thick plaster to internal & external walls at all heights/depths with cement mortar 1:6 (1 cement :6 fine sand) finished smooth/rough including raking out joints, rounding off and chamfering corners, making drip course moulding, roughening of brick surface, curing for etc. complete as per specifications.

Supplying and placing in position 5 mm thick steel chequred plates over cable ducts, valve pits etc. including provision for lifting arrangements complete in all respects inclusive of cost of all labour, materials, tools, tackles etc. as per drawings, specifications and direction of Site Engineer.

Construction of STAIR- Supplying, fabricating, erecting, placing and fixing in position M.S. structural works using rolled/ built up sections for truss, claddings, bracings, purlins, supporting frames made of joists, tubes, pipes, channels, angles, plates,flats, bars etc. including cutting to required size welding of joints, fixing anchor plates, including bolts, theading, nuts, washers, sleeves etc. including preparation of detailed fabrication drawings & submission to Engineer-in-charge for approval before start of fabrication, supplying & applying painting with two coats of epoxy paint "EPILUX 155 High Build Enamel over a coat of EPILUX 610 Primer of M/s Berger or any other approved equivalent make as per manufacturer’s recommendation, complete in all respects inclusive of cost of all labour, materials, tools, tackles etc. as per drawings, specifications and direction of Site Engineer. (excluding the cost of concrete work).

Supplying and spreading of approved quality,fine, dry /river sand in cable trenches as per drawings, specifi- cations and directions of the Site Engineer, including the cost of all material, transport, load and lift charges, labour,tools etc. complete in all respects.

Painting work including Surface preparation ,etc. as per technical specifications and tender scope of work: Supplying and applying three coats of super acrylic emulsion paint like RANGOLI of Berger or any other approved equivalent brand, of required shade on newly plaster surface including preparation of base surface with putty, two coats of cement primer, scaffolding etc. complete in all respects inclusive of cost of all labour, materials, tools, tackles etc. as per manufacturer’s recommendations, specification and direction of Site Engineer.

Painting works for steel work as per technical specifications and tender scope of work : Providing and applying painting with synthetic enamel paint in two or more coats on new work of approved brand and manufacture to give an even shade including cleaning of surface complete as per specfication and direction of Engineer-in-Charge/Site Engineer.

Providing and laying cement concrete of mix 1:4:8 (1 cement:4 coarse sand :8 graded stone aggregate 40 mm nominal size) for foundation works at all depths including ramming, dewatering & shuttering etc. complete in all respects inclusive of cost of all labour, materials, tools, tackles etc. as per drawings, specifications and direction of Site Engineer.

services

Excavation as per scope of work and technical specifications for depth above 2.5 m

Supply of Gaskets 1" SWMG ANSI 600# as per technical specifications

M/s S S Enterprises