REPAIR TO ROOF SHEETS, FALSE CEILING, JOINERY, FLOORING, SMART PERIODICAL SERVICES, CLEANING OF SEWAGE LINE SEPTIC TANK SOAK WELL MANHOLES AND OTHER MISC B AND R WORKS AT TAMALPUR AND DARRANGA MIL STN UNDER GE RANGIA

Amount

Taking down cement plaster on brick or stone walls, etc. including raking out joints, hacking for key, scrubbing down with water, etc., complete all as specified and as directed by Engineer-in-charge.

Dismantling Asbestos cement (corrugated, semi-corrugated, etc.) sheets in roof coverings, complete all as specified and as directed by Engineer-in-charge.

Dismantling timber scantlings 40 sq. cm and over in section, in any position and in unframed work, complete all as specified and as directed by Engineer-in-charge.

Dismantling timber fillets, rails, posts, rafters, purlins, etc. under 40 sq. cm in section and in unframed work, complete all as specified and as directed by Engineer-in-charge.

Dismantling posts or struts (wood, steel or R.C.C.) of any section, embedded in concrete/ brick/ masonary including taking out embedded portion and making good disturbed ground, complete all as specified and as directed by Engineer-in-charge.

Taking down Chowkhats or frames with shutters (without taking off shutters from the frames) exc 1.5 sq. m but not exc. 4.0 sq. m each, complete all as specified and as directed by Engineer-in-charge.

Dismantling wrought iron or mild steel work of any description not otherwise provided for, complete all as specified and as directed by Engineer-in-charge.

M&L for resecuring or easing & adjusting without taking down of aluminium door Shutters of any description, including refixing/tightening of hinges, handles, tower bolts and other accessories with and including providing new brass CP screws, aluminium snap beading, rubber gasket, etc. (If required), complete all as specified and as directed by Engineer-in-charge.

M&L for resecuring or easing & adjusting without taking down of wooden door Shutters of any description, including refixing/tightening of hinges, handles, tower bolts and other accessories with and including providing new brass CP screws (If required), complete all as specified and as directed by Engineer-in-charge.

M&L for precast reinforced cement concrete 1:2:4, type-B1 (Using 20 mm graded stone aggregate) in landings, cover slabs (for manholes, etc.) shelves and similar articles with plain faces and set in cement mortar 1:4, incl demolition of existing RCC complete all as per specified and as directed by Engineer-in-charge. NOTE : Reinforcement will be measured and paid separately under relevant Item.

S&F of TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips, complete all as specified and as directed by Engineer-in-charge.

M&L for Providing Cement Concrete 1:2:4, type B-1 (20mm graded aggregate) as in benching/Coping, edging, lintels upto 1.5m clear span, cills, steps; hold-fast block, filling in pressed steel frames, seismic and other similar bands etc. and finishing the Concrete surfaces Fair and Even including necessary Formwork required at Site(s), incl demolition of existing PCC complete all as specified and as directed by Engineer-in-charge.

M&L for PCC 1:4:8 type D-2 (40mm graded stone aggregate) as in foundations, fillings and mass concrete incl demolition of existing PCC, complete all as per specified and as directed by Engineer-in-charge.

S&F of 6mm thick asbestos cement, corrugated or semi-corrugated sheets with two corrugations side lap fixed with L-type or J-type or cranked hook bolts in roof, wall etc., complete all as specified and as directed by Engineer-in-charge.

S&F of 0.50mm thick Pre-painted galvalume aluminum zinc coating GI based corrugated steel sheet of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws, complete all as specified and as directed by Engineer-in-charge.

S&F in-repair of exposed powder coated GI snap grid frame work (600x600 mm) for false ceiling comprising of wall/cleat angle of size 25x25x0.35mm and cross tee of size 24x38x0.70mm with suspended hangers of 1 mm dia. G.I. (upto 1200mm length) adjusting level fixed to any type of roof by means of ceilling cleats made out of G.I. flat 40 x 3 mm size 60mm long and expansion hold fasteners 12.5mm dia. 40mm long with and including fixing/ laying/ inserting of pre-painted (white) 4mm thick designer classic E-boards (595x595 mm) to GI frame work, complete all as specified and as directed by Engineer-in-charge.

S&F in-repair of hollow PVC wall panneling consisting of 5mm thick wood grain printed PVC sheet inclusive of solvent cement and fixing at site on PVC frame as per specification, complete all as specified and as directed by Engineer-in-charge.

M&L for second class hard wood plain fillets in square, rectangular or triangular in section, clean sawn, secured with nails or brads of sectional area exc. 13sqcm but not exc.25sqcm, complete all as specified and as directed by Engineer-in-charge.

M&L for 2nd class hard wood in scantling wrought timber unframed and fixed, complete all as specified and as directed by Engineer-in-charge.

S&F of Steel work in tubular trusses including special shaped washer etc. complete using ERW or induction butt welded tubes conforming to I. S.1161- 1979 grade St.-240, complete all as specified and as directed by Engineer-in-charge.

S&F of mild steel posts and struts in fencing including cutting tops to shape as directed, drilling holes, notching for wire, etc.; flat iron fillets (for securing wire mesh etc.), wall ties, hold-fast, wind ties including all necessary drilling, bolting or riveting, etc., and similar work conforming to Fe-290 Gde E-165, complete all as specified and as directed by Engineer-in-charge.

S&F of mild steel Framed work as in doors or gates of angle or other section with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering. Doors, etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails and guides) and hanging; also fastening and fixing, confirming to Fe 410-W (Gde- E- 250) quality-A, complete all as specified and as directed by Engineer-in-charge.

S&F in-repair of laminated PVC Shelves/Cabinet of 400mm depth made out of 18mm thick one side decorative lamination & other side white lamination sheet & provision of shelves and shutters made out of 18 mm thick one side decorative laminated PVC sheet including all required brackets, SS screws, SS knobs, SS Handles, etc. The panels shall be fabricated using adhesive and screws where ever required. All the edges shall be covered with 2 mm thick edge bonding tape or 90º edge bent finish, completer all as specified and as directed by engineer-in-charge. (NOTE:- Only front face shall be measured and paid.)

S&F of 30mm thick factory made second class hard wood Flush shutters, solid core construction, with particle board core and plywood face panels, commercial type on both sides and one face is covered with decorative face veneer with lipping/frame to match; complete all as specified and as directed by Engineer-in-charge.

S&F of 35mm thick factory made second class hard wood Flush shutters, solid core construction, with particle board core and plywood face panels, commercial type on both sides; complete all as specified and as directed by Engineer-in-charge.

S&F of 35mm thick factory made second class hard wood Glazed and skeleton shutters, open rebated and prepared to receive glass, gauze, etc. (with sash bars), divided into squares and edges of framing plain, chamfered or rounded. fitted with cut and mitred beads for securing glass, etc.; sizes of members of shutters as specified in SSR Part I, Section 8, clause 8.24 (a); complete all as specified and as directed by Engineer-in-charge.

M&L for second class hard wood plain, solid, straight chowkats and frames, wrought, framed rebated on the solid, rounded or chamfered, put together with glue pinned at joints, complete all as specified and as directed by Engineer-in-charge.

S&F of Solid PVC moulded Door Frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S. Square tube; complete all as specified and as directed by Engineer-in-charge.

S&F of Solid PVC Door Frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S. Square tube; complete all as specified and as directed by Engineer-in-charge.

S&F of Factory Made Solid PVC Moulded Door Shutter With Particle Board Core, 28 to 30mm thick (stiles), with 2, 4, or 6 raised panel design with 2mm thick Moulded PVC Sheet on the front face & 2mm plain colour PVC sheet on back face; complete all as specified and as directed by Engineer-in-charge.

S&F of Factory made solid wire gauzed panel PVC door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a prelam PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and prelam PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; wire gauze shall be wrapped on an additional square 8mm M.S. Solid tube and this tube shall be welded to M.S. tubes. The wire gauge shall be stretched to tighten firmly; complete all as specified and as directed by Engineer-in-charge.

S&F of Factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement; complete all as specified and as directed by Engineer-in-charge.

S&F in-repair of powder coated aluminium anodised door using 96.6x44.8x1.5mm thick powder coated Anodised aluminium section as in chowkhat, 84.0x44.7x1.5mm thick section as in vertical styles and 101.6x44.88x1.5mm thick section as in rails with and including necessary joining cleats, glazing clips, ruber neoprene packing, 200mm long powder coated aluminium handles 2 Nos in each door, 100mm long medium grade stainless steel butt hinges of 4 Nos, 1 No aluminium (extruded section) body Door closer hydraulically regulated suitable for door shutters of 851 to 1000 mm in width and of weight between 61 to 80 kg, 1 No brass body 6-lever Mortice lock, vertical type, size 100 mm, 1No 140 mm Overall length of cover plate Floor door stopper of aluminium alloy body and tongue, anodised, with hard drawn steel spring and rubber end, powder coated anodised aluminum snap beading screws etc., complete all as specified and as directed by Engineer-in-charge.

S&F of Galvanised mild steel wire cloth, 0.56mm nominal dia of wire and average width of aperture 1.18mm and fixed with tinned tacks, or galvanised wire staples, complete all as specified and as directed by Engineer-in-charge.

S&F of 100 mm long Butt hinges, medium weight, Stainless steel, complete all as specified and as directed by Engineer-in-charge.

S&F of 200 mm long Aluminium anodised, barrel tower bolts of extruded section, complete all as specified and as directed by Engineer-in-charge.

S&F of 150 mm long Extruded aluminium alloy handles, fabricated type, anodised, complete all as specified and as directed by Engineer-in-charge.

S&F of 300 mm long Aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy, complete all as specified and as directed by Engineer-in-charge.

S&F in-repair of 3mm thick Sheet glass, ordinary quality and glazing with oil putty in square n exc 0.5 sq. m in each pane, complete all as specified and as directed by Engineer-in-charge.

S&F in-repair of brass body 300mm long, ordinary rat tail rod pattern springs including roller and roller plate, complete all as specified and as directed by Engineer-in-charge.

S&F in-repair of 300 mm long Aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy, complete all as specified and as directed by Engineer-in-charge.

S&F in-repair of 100 mm long Butt hinges, medium weight, mild steel, complete all as specified and as directed by Engineer-in-charge.

S&F in-repair of 200 mm long Aluminium anodised, barrel tower bolts of extruded section, complete all as specified and as directed by Engineer-in-charge.

S&F in-repair of 150 mm long Extruded aluminium alloy handles, fabricated type, anodised, complete all as specified and as directed by Engineer-in-charge.

S&F in-repair of 19/20 mm dia anodised aluminium alloy curtain rail with fixing brackets, stops, rollers etc., complete all as specified and as directed by Engineer-in-charge.

S&F in-repair of 150 mm Overall length of cover plate double legged Floor door stopper of aluminium alloy body and tongue, anodised, with hard drawn steel spring and rubber end, fixed in floor, complete all as specified and as directed by Engineer-in-charge.

S&F in-repair of aluminium die-cast body Door closer hydraulically regulated, designation No. 3, universal type, suitable for door shutters of 851 to 1000 mm in width and of weight between 61 to 80 kg, complete all as specified and as directed by Engineer-in-charge.

S&F in-repair of Galvanised mild steel wire cloth, 0.56mm nominal dia of wire and average width of aperture 1.18mm and fixed with tinned tacks, or galvanised wire staples, complete all as specified and as directed by Engineer-in-charge.

S&F in-repair of PVC connection pipe 15mm dia with PTMT nuts of length 450mm, complete all as specified and as directed by Engineer-in-charge.

S&F in-repair of 32mm dia Waste coupling of PTMT (half or full threaded) suitable for sink/urinals (Minimum weight 32mm- 45gms), complete all as specified and as directed by Engineer-in-charge.

S&F in-repair of 75mm dia PVC (SWR) floor trap, plain with grating including jointing with solvent cement, complete all as specified and as directed by Engineer-in-charge.

S&F in-repair of Brass chromium plated Toilet paper holder flat recessed type, fixing to wall with CP brass screws, complete all as specified and as directed by Engineer-in-charge.

S&F in-repair of 15mm dia galvanised steel tubes, 'medium grade', with all fitting; fixed to walls and ceilings or laid in floors, complete all as specified and as directed by Engineer-in-charge.

S&F in-repair of 20mm dia galvanised steel tubes, 'medium grade', with all fitting; fixed to walls and ceilings or laid in floors, complete all as specified and as directed by Engineer-in-charge.

S&F in-repair of 25mm dia galvanised steel tubes, 'medium grade', with all fitting; fixed to walls and ceilings or laid in floors, complete all as specified and as directed by Engineer-in-charge.

S&F in-repair of Rotational Moulded Polyethylene Water Storage Tank 500 Litre capacity (Cylindrical Vertical with Closed Top), 3 layered, hoisted and fixed in position, all as specified in MES Schedule Part-I with and including providing 20 mm dia ball valves high pressure of PTMT with epoxy coated aluminium rod & high density plastic ball screwed for iron pipe and fixed (Minimum weight 210gm), complete all as specified and as directed by Engineer-in-charge.

All as per Item No. 58 here-in-above, but for 1000 Litre capacity water tank, complete all as specified and as directed by Engineer-in-charge.

S&F in repair of PVC water tank cover suitable for any capacity PVC water tank with 6mm dia MS bar hinging device and S type locking arrangements, complete all as specified and as directed by Engineer-in-charge.

S&F of 20 mm bore (dia), gun metal gate valves with iron wheel head, screwed both ends for iron pipe, ISI Marked, as per IS: 778 and including taking out old unserviceable gate valves complete all as specified and as directed by Engineer-in-charge.

S&F in-repair of 20 mm dia ball valves high pressure of PTMT with epoxy coated aluminium rod & high density plastic ball screwed for iron pipe and fixed (Minimum weight 210gm), complete all as specified and as directed by Engineer-in-charge.

S&F in-repair of 25 mm dia ball valves high pressure of PTMT with epoxy coated aluminium rod & high density plastic ball screwed for iron pipe and fixed (Minimum weight 455gm), complete all as specified and as directed by Engineer-in-charge.

S&F in-repair of sinks made of stainless steel lmm thick kitchen or laboratory with plugs, washers and wastes; including bedding in cement mortar on to dwarf wall or including fixing cantilever brackets and connecting union to pipe, overall size 495mm x 420mm bowl size 410mm x 330mm x 160mm, complete all as specified and as directed by Engineer-in-charge.

S&F in-repair of sinks with drainage board made of stainless steel lmm thick kitchen or laboratory with plugs, washers and wastes; including bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connecting union to pipe overall size 915mm x 460mm bowl size 410mm x 330mm x 160mm, complete all as specified and as directed by Engineer-in-charge.

S&F in-repair of 32 mm dia 900mm long PVC Flexible waste pipe with 32mm dia Waste coupling of PTMT (half or full threaded) (Minimum weight 32mm- 45gms) suitable for sink, basin, complete all as specified and as directed by Engineer-in-charge.

S&F in-repair of 15 mm dia fancy type chromium plated Bib taps, cast copper alloy with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule, complete all as specified and as directed by Engineer-in-charge.

S&F in-repair of 15 mm dia fancy type chromium plated Pillar taps, cast copper alloy, with capstan heads, screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly-nuts, screwed for iron pipe, complete all as specified and as directed by Engineer-in-charge.

S&F in-repair of 15 mm dia fancy type Brass CP telephonic wall mixer (without hand shower and hose) for mixing hot & cold water, screwed for iron pipe, complete all as specified and as directed by Engineer-in-charge.

S&F in-repair of 15 mm dia fancy type Brass CP basin mixer without pop up waste for mixing hot & cold water, screwed for iron pipe, complete all as specified and as directed by Engineer-in-charge.

S&F in-repair of 15 mm dia fancy type chromium plated Bib taps 2-in-1 (2-way), cast copper alloy with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule, complete all as specified and as directed by Engineer-in-charge.

S&F in-repair of Health faucet (ABS Body) mild steel chromium plated suitable for 15 mm dia pipe with 1.25 metre long flexible tube and ABS wall hook including making connections and fixed in position, complete all as specified and as directed by Engineer-in-charge.

S&F in-repair of Brass chromium plated Soap Dish, fixing to wall with CP brass screws, complete all as specified and as directed by Engineer-in-charge.

S&F in-repair of Brass chromium plated towel rack/ shelf, 225mm wide, 600mm long between flanges, complete all as specified and as directed by Engineer-in-charge.

S&F in-repair of Brass chromium plated Tubular towel rail, 20mm dia, D type, 60cm long between flanges, complete all as specified and as directed by Engineer-in-charge.

S&F in-repair of Brass chromium plated towel ring, fixing to wall with CP brass screws, complete all as specified and as directed by Engineer-in-charge.

S&F in-repair of 15 mm dia Bib tap standard of PTMT any colour high pressure screwed for iron pipe and fixed (Minimum weight 15mm-90gms), complete all as specified and as directed by Engineer-in-charge.

S&F in-repair of 15 mm dia fancy type, chromium plated Stop valves/ Angle valve, cast copper alloy, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions, complete all as specified and as directed by Engineer-in-charge.

S&F in-repair of Brass chromium plated shower rose of 125mm dia of rose, fixing to existing pipe or union of 15 mm dia, complete all as specified and as directed by Engineer-in-charge.

M&L for sand filling under floors or in foundations spreading and levelling in layers not exc. 25 cm thick including watering and consolidation, complete all as per specified and as directed by Engineer-in-charge.

M&L for providing Machine pressed precast coloured concrete interlocking paver block any shape and size confirming to IS 15658-2006 of 80 mm thickness, M-40 Grade, with grey cement and pigment, including dismantling the existing old unserviceable tiles of any type and of any description, complete all as per specified and as directed by Engineer-in-charge.

M&L for providing glossy finished PU coated Chequered cement concrete coloured tiles 30cm x 30cm x 25mm thick, set, jointed and pointed in neat cement slurry in floors., laid over 20mm thick cement screed 1:6 with grey cement and pigments to match, including dismantling the existing old unserviceable tiles of any type and of any description, complete all as per specified and as directed by Engineer-in-charge.

M&L for providing Vitrified Ceramic light shade tiles 8 to 10 mm thick (square/ rectangular) area of each tile not exceeding 0.36 sqm, in floors etc., laid over 20mm thick cement screed 1:6 set and jointed in neat cement slurry and pointed in white or coloured cement to match, including dismantling the existing old unserviceable tiles of any type and of any description, complete all as per specified and as directed by Engineer-in-charge.

M&L for providing Vitrified Ceramic light shade tiles 8 to 10 mm thick (square/ rectangular) area of each tile not exceeding 0.36 sqm, in vertical surface (like skirting, dado, etc.), over 10mm thick cement screed 1:3 set and jointed in neat cement slurry and pointed in white or coloured cement to match, including dismantling the existing old unserviceable tiles of any type and of any description, complete all as per specified and as directed by Engineer-in-charge.

M&L for providing Non-skid Ceramic coloured tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors etc., laid over 20mm thick cement screed 1:6 set and jointed in neat cement slurry and pointed in white or coloured cement to match, including dismantling the existing old unserviceable tiles of any type and of any description, complete all as per specified and as directed by Engineer-in-charge.

M&L for providing Glazed ceramic coloured tiles in vertical surface (like skirting, dado, etc.) 450x 300x 7-8 mm thick, over 10mm thick cement screed 1:3 set and jointed in neat cement slurry and pointed in white or colour cement to match, including dismantling the existing old unserviceable tiles of any type and of any description, complete all as per specified and as directed by Engineer-in-charge.

M&L for providing matt-finished/ stone finished ceramic coloured tiles in vertical surface (like skirting, dado, etc.) 450x 300x 7-8 mm thick, over 10mm thick cement screed 1:3 set and jointed in neat cement slurry and pointed in white or colour cement to match, including dismantling the existing old unserviceable tiles of any type and of any description, complete all as per specified and as directed by Engineer-in-charge.

M&L for Granite (of any type) tiles 20mm thick machine cut, over 20mm thick cement screed base 1:6, bedded and jointed with grey cement slurry and pointed with white cement with admixture of pigment to match the shade of granite stone including grinding and polishing, including dismantling the existing old unserviceable stone slab of any type and of any description, complete all as per specified and as directed by Engineer-in-charge.

M&L for providing 75 mm thick Cement concrete type C-2, 1:3:6 (40mm graded stone aggregate) as in floor/ path/ hardstanding/plinth protection, etc. or similar works, laid in altenate bays including use and waste of form work and finishing concrete surfaces even and smooth with using extra cement and demolition of existing old unserviceable concrete, complete all as per specified and as directed by Engineer-in-charge.

M&L for providing 100 mm thick Cement concrete type C-2, 1:3:6 (40mm graded stone aggregate) as in sub-base of floor/ path/ hardstanding/plinth protection, etc. or similar works, laid in altenate bays including use and waste of form work and finishing concrete surfaces even and smooth without using extra cement, including demolition of the exisiting old PCC, complete all as per specified and as directed by Engineer-in-charge.

M&L for providing 50 mm thick Cement concrete type C-2, 1:3:6 (40mm graded stone aggregate) as in sub-base of floor/ path/ hardstanding/plinth protection, etc. or similar works, laid in altenate bays including use and waste of form work and finishing concrete surfaces even and smooth without using extra cement, including demolition of the exisiting old PCC, complete all as per specified and as directed by Engineer-in-charge.

M&L for Brickwork with subclass ‘B’ bricks, straight or curved on plan to any radius built and set in cement mortar 1:6, incl demolition of existing B/W,complete all as per specified and as directed by Engineer-in-charge.

M&L for Brickwork with subclass ‘B’ bricks, straight or curved on plan to any radius in half brick thick walls built and set in cement mortar 1:4, incl demolition of existing B/W, complete all as per specified and as directed by Engineer-in-charge.

M&L for Rendering 15mm thick in cement morter 1:4 on fair faces of brick work or concrete surfaces, finished even and smooth (without using extra cement), complete all as specified and as directed by Engineer-in-charge.

M&L for Rendering 15mm thick in cement morter 1:4 on fair faces of brick work or concrete surfaces, finished even and smooth (with using extra cement), complete all as specified and as directed by Engineer-in-charge.

M&L for Rendering 10mm thick in cement morter 1:4 on fair faces of brick work or concrete surfaces, finished even and smooth (without using extra cement), complete all as specified and as directed by Engineer-in-charge.

M&L for preparing newly plastered surfaces of wall and applying two coats of distemper oil emulsion of any shade over a coat of alkali-resistant and a coat of avg 2.00mm thick wall care putty including rubbing down the putty surfaces to obtained smooth finish, complete all as specified and as directed by Engineer-in-charge.

M&L for Preparing surfaces of wood and wood based materials, new or old, of any description and girth, not otherwise described and treated with two coats of Creosote oil, complete all as specified and as directed by Engineer-in-charge.

M&L for preparation of new or previously un-treated steel/iron surfaces of any description, not otherwise described, over 10cm width or girth and applying two coats of black japan paint (1st quality) over a coat of red oxide primer, complete all as specified and as directed by Engineer-in-charge.

M&L for preparation of new or previously un-treated wooden Surfaces of any description, not otherwise described, over 10cm width or girth and applying two coats of Synthetic enamel paint (1st quality) of any tint over a coat of pink primer, complete all as specified and as directed by Engineer-in-charge.

M&L for preparing newly plastered surfaces of wall and applying two coats of cement base paint of any shade over a coat of chalk whitening, complete all as specified and as directed by Engineer-in-charge.

M&L for preparing newly plastered surfaces of wall and applying two coats of distemper oil emulsion of any shade over a coat of chalk whitening, complete all as specified and as directed by Engineer-in-charge.

M&L for preparation of new or previously un-treated steel/iron surfaces of any description, not otherwise described, over 10cm width or girth and applying two coats of Synthetic enamel paint (1st quality) of any tint over a coat of red oxide primer, complete all as specified and as directed by Engineer-in-charge.

M&L for preparing newly plastered surfaces of wall and applying three coats of white wash, complete all as specified and as directed by Engineer-in-charge.

M&L for preparing old treated/decorated Plastered/Unplastered Surfaces of Walls by Vaccum based sanding machine and eliminating smoke soot, moulds, moss and efflorescent salts and trading oil and greasy spots and applying One Coat of white wash, complete all as directed by Engineer-in-charge.

All as per Item No. 105 here-in-above, but applying Two Coats of white wash, complete all as specified and as directed by Engineer-in-charge.

All as per Item No. 105 here-in-above, but on Ceiling, complete all as specified and as directed by Engineer-in-charge.

All as per Item No. 105 here-in-above, but applying One Coat of Distemper Oil Emulsion of approved colour by means of spray machine, complete all as specified and as directed by Engineer-in-charge.

All as per Item No. 108 here-in-above, but on Ceiling, complete all as specified and as directed by Engineer-in-charge.

All as per Item No. 105 here-in-above, but applying One Coat of Cement base paint of approved colour by means of spray machine, complete all as specified and as directed by Engineer-in-charge.

M&L for preparation of old painted wooden Surfaces of any description, not otherwise described, over 10cm width or girth and applying one coat of Synthetic enamel paint (1st quality) of any tint, complete all as specified and as directed by Engineer-in-charge.

M&L for preparation of old painted wooden Surfaces of any description n exc 10cm width or girth when unconnected with other painting or when painted in different tint and applying one coat of Synthetic enamel paint (1st quality) of any tint, complete all as specified and as directed by Engineer-in-charge.

M&L for preparation of old painted steel/ iron surfaces of any description, not otherwise described, over 10cm width or girth and applying one coat of Synthetic enamel paint (1st quality) of any tint, complete all as specified and as directed by Engineer-in-charge.

M&L for preparation of old painted steel/ iron surfaces of any description, n exc 10cm width or girth when unconnected with other painting or when painted in different tint and applying one coat of Synthetic enamel paint (1st quality) of any tint, complete all as specified and as directed by Engineer-in-charge.

M&L for complete removal of existing surfaces and applying two coats of oil bound distemper over a coat chalk whitening priming, both using mechanical spray machine, applied over 1.0mm thick wall care putty(using multipurpose mixer machine) finished and smooth on wall complete all as specified and directed.

M&L, for Premium Acrylic Smooth exterior paint with Silicone additives of required shade, applied @ 1.43 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm using mechanical spray machine, over smooth and even wall care putty to wall surfaces including complete removal of existing treatment, complete all as specified and as directed by Engr-In-Charge.

M&L for Writing letters or figures (Block. Roman, Italic or Indian) n exc. 30 cm high with synthetic enamel paint including necessary preparation of surfaces, complete all as specified and as directed by Engineer-in-charge.

S&F in-repair of Vitreous China bowl urinal flat back, size of 465 x 355 x 265 mm white with and including grating, 15mm dia 450mm long PVC connection pipe and 32mm dia 900mm long PVC Flexible waste pipe and providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including 60mm long CP brass screws, pointing around urinal back in putty; complete all as specified and as directed by Engineer-in-charge.

S&F in-repair of Vitreous China wash basin, white, with brackets, flat back, size 550x400mm including cutting for and pinning in ends of brackets or erecting stand, fixing of 15mm dia 450mm long PVC connection pipe and 32mm dia 900mm long PVC Flexible waste pipe with and including 32mm dia Waste fittings, brass, chromium plated for glazed ware sinks, basins, etc. with long screwed shanks and fly-nuts, flange end bedded in red lead cement and other end fixed with providing 15mm dia fancy type Pillar taps, cast copper alloy, with capstan heads, chromium plated, screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly-nuts; complete all as specified and as directed by Engineer-in-charge.

S&F in-repair of Wash down water closet (Pedestal pattern) pan and S/P trap of 540x375x415mm with and including Plastic water closet seat, white, closed pattern with flat bottom, and cover and mild steel chromium plated or anodised aluminium hinging device including connection to drain (or outgoing pipe) and to flushing pipe, antisyphonage pipe, etc., complete all as specified and as directed by Engineer-in-charge.

S&F in repair vitreous china wash down water closet pan (pedestal pattern- couple closet) of size 360x680x765 mm, S/P trap - 220mm, white, including seat cover with chromium plated hinging device, brackets, jet spray, PVC connection pipes including making good disturbed surfaces in cement mortar 1:3, complete all as per specified and as directed by Engineer-in-charge.

S&F in-repair of 10 litre capacity PVC valveless, syphonic action type, flushing cistern, low level, white, with inlet, ball valve, float and handle including brackets and PVC flush pipe of 32 mm dia, with and including making necessary connections, complete all as specified and as directed by Engineer-in-charge.

M&L for Demolition and breaking up of 100mm dia Salt glazed stone ware drain pipes set in cement mortar, complete all as specified and as directed by Engineer-in-charge. NOTE:- Excavation work shall be measured and paid separately.

M&L for Demolition and breaking up of 150mm dia Salt glazed stone ware drain pipes set in cement mortar, complete all as specified and as directed by Engineer-in-charge. NOTE:- Excavation work shall be measured and paid separately.

M&L for providing cement concrete 1:3:6, type C-2 (40mm graded aggregates) bed to 110mm dia drain pipes including packing under and haunching against the sides of pipes after they are laid and tested, complete all as specified and as directed by Engineer-in-charge.

M&L for providing cement concrete 1:3:6, type C-2 (40mm graded aggregates) bed to 150mm dia drain pipes including packing under and haunching against the sides of pipes after they are laid and tested, complete all as specified and as directed by Engineer-in-charge.

S&F PVC (SWR) pipes 110 mm bore single socketed, in any length with rubber ring joints, incl bend/ branches laid in trenches or in floor complete all as specified and directed.

S&F PVC (SWR) pipes 150 mm bore single socketed, in any length with rubber ring joints, incl bend/ branches laid in trenches or in floor complete all as specified and directed.

M&L for providing 150mm dia Reinforced concrete pipes, class NP2, laid and jointed complete with collars, complete all as specified and as directed by Engineer-in-charge.

M&L for cleaning of septic tanks of any capacity along with removing of sludges mixed with water etc and carrying to a distance exc. 100 meters but n.exc 250 meters and depositing in ditches including necessary excavation and earth work in soft/loose soil for making ditches and refilling the ditches after the sludge’s are deposited with spreading and leveling of excavated soils in the ditches over the sludge, removing surplus soils to a distance n.exc 50m and supply and sprinkling bleaching powder over the area of ditches with one meter around complete all as specified and directed.

Cleaning of manhole and removal of sludge of any size and depth upto 0.75 Mtr incl shifting of manhole cover and placing in position, complete all as specified and as directed by Engineer-in-charge.

Cleaning of manhole and removal of sludge of any size and depth from 0.75mtr and upto 1.50mtr incl shifting of manhole cover and placing in position, complete all as specified and as directed by Engineer-in-charge.

S&F in repair Urinal spreader of PTMT any colour for fixing with 15 mm dia pipe (Minimum weight 60 grams) complete all as per specified and as directed by Engineer-in-charge.

S&F in repair Flush pipe of polyethylene of high density or PVC 32 mm dia incl necessay washers, for low level cistern complete all as specified and as directed by Engr-in-Charge.

M&L for cleaning of sewage pipe line by rodding/pumping between intermediate/1st manholes to manholes or between manholes to septic tanks or between septic tank to soak pits to remove all blockage and well flushing with water including making good of leakage in joints wherever required in cement mortar (1:2) including removing the sludge and re-fixing the manhole cover complete all as specified and as directed by Engineer-in-charge.

S&F in-repair of 75mm dia PVC (SWR) pipes single socketed, in any length with rubber ring joints, fixed to walls, complete all as specified and as directed by Engineer-in-charge.

S&F in-repair of 75mm dia PVC (SWR) vent cowl, complete all as specified and as directed by Engineer-in-charge.

S&F in-repair of 15 mm dia fancy type chromium plated swan neck Pillar taps, cast copper alloy, with capstan heads, screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly-nuts, screwed for iron pipe, complete all as specified and as directed by Engineer-in-charge.

MUKUL CHOUDHURY

M/s Priyanka Construction

OM CONSTRUCTIONS

M/S NARAYAN ENTERPRISE