SPECIAL REPAIR TO BLDG NO P-228 (SUDHIR GYM) AT JAK RRC UNDER

Amount

Complete removal of existing treatment on walls including steel wire brushing and scrapping etc and applying 3mm thick( Avg) Birla wall care putty in two layers on wall surfaces including rubbing, levelling and preparing the surfaces for receiving further finishes complete all as specified and directed.

M&L for applying two coat of distemper Oil emulsion, white or tinted, on new putty surfaces of wall complete all as specified and directed.

M & L for Providing and injecting chemical emulsion for Post-Constructional Anti-Termite Treatment of soil under existing floors using emulsion @ one litre per hole,300mm apart including drilling and plugging 12mm dia holes with cement mortar (1:2)(1cement:2 coarse sand) to match with the existing floors complete all as specified and directed.

M & L for Providing and injecting chemical emulsion for Post-Constructional Anti-Termite Treatment along the external wall below concrete or masonry apron using chemical emulsion @ 2.25 Litres per linear metre including drilling and plugging holes etc. in apron complete all as specified and directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing) including removal of debris to out side MD land complete all as specified & directed.

Demolition of cement concrete of any description (unreinforced) in ground floors and paving not exceeding 15 cms thickness (below or above ground level) including removal of debris to out side MD land complete all as specified & directed.

M&L for 25mm thick PCC (1:2:4) Type B-0 using 12.50 mm graded crushed stone aggregate as in floor, surface finished even & fair without using extra cement complete all as specified and directed.

M & L Non Skid ceramic joint free tiles 7 to 8 mm thick ( square / rectangular) area of each tile exceeding 0.11 Sqm but not exceeding 0.18 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match with the shade of tiles, over and including 15 mm thick screed bed or bedding layer in CM 1:6 complete all as specified and directed.

M&L for glazed ceramic tiles (coloured) 350x250x7mm / 450x350x7mm thick in vertical surfaces such as skirting, dado and risers to steps, set and jointed in neat cement slurry and pointed in coloured cement to match with the shade of tiles, over and including 10mm thick cement mortar (1:4) on fair faces of brick work or concrete surfaces as backing for tiles complete all as specified and as directed.

S&F chromium plated health faucet with 8 mm hole dia and 1.2m long flexible tubes with and including wall hook suitable for EWC including nut/washer complete all as specified and directed. ( Make : Jaquar, Code ALD-573 or Equivalent as approved by GE)

M&L 20-25mm thick Cudappah stone slab on cooking platform/shelf , machine cut, over and including 20mm thick screed bed in CM 1:6, laid and jointed with grey cement slurry mixed with pigment to match with the shade of slab including rubbing and polishing and cutting of holes for gas pipe complete all as specified and directed.

M & L Granite (Black/Ruby Red ) work (table rubbed and polished) 20 mm thick in cooking platforms bedded and jointed with grey cement slurry and pointed with white cement with admixure of pigment to match with the shade of granite stone including grinding and polishing complete over and including screed bed 15 mm thick in CM 1 : 6 and cutting of holes for gas pipe complete all as specified and directed.

S&F solid PVC door frame of size 50mm x 47mm made out of 5mm plain clour PVC sheet reinforced with M.S square tube in opening complete all as specified and directed.

S&F factory made solid panel PVC door shutter 30mm thick (Style) consisting of frame made out of MS tubes for top, bottom and side rails, MS frame shall be covered with heat molded plain colour PVC “C” channel having a PVC sheet strip of 20 mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail lock rail & bottom rail on either side and as gap insert for top rail and bottom rail paneling of plain colour PVC sheet to be fixed in the MS frame welded /sealed to the stiles and rails with suitable PVC sheet beading and jointed together with solvent cement and fixing in the frame at site complete all as specified and directed.

S&F 100 mm long butt hinges, extruded aluminium alloy with galvanised mild steel hinge pin, anodised and fixed, type C-21 complete all as specified and directed.

Supply and fix 150mm long aluminium anodised barrel tower bolts of extruded section complete all as specified & directed.

Supply and fix aluminium handles 125mm size, cast type, anodised complete all as specified & directed.

Supply and fix, in repair, 10 ltr capacity PVC valveless syphonic action type flushing cistern low level 'white' with inlet ball valve, float valve & handle Including 32mm bore PVC flush pipe & brackets and brackets fixed to wall complete all as specified & directed.

S&F in repair 125mm dia mild steel chromium plated grating fixed on floor trap / nahani trap in Cement Mortar (1:6) , complete all as specified and as directed by Engr-in-charge.

Supply & fix, in repair, vitreous china squatting pan, Orissa pattern of size 580x440 mm white, with integral foot rest and PVC 'P' or 'S' trap including connection to trap, and to flush pipe, etc (excluding flushing pipe) and making good to floor complete all as specified & directed.

Supply & fix, in repair, vitreous china wash down water closet pan (pedestal pattern) white (excluding fixing bolts, flushing cistern and flush pipe) but plastic water closet seat, black/ white, closed pattern with recessed bottom, and cover and mild steel chromium plated or aluminium hinging device, complete all as specified & directed.

S&F, in repairs, vitreous china full stall urinals, white, with urinal spreader complete including providing and fixing plugs, securing urinals to plugs with and including 60mm long brass screws, fixing flush pipe, grating and union for discharge pipe complete all as specified & directed..

S&F Plastic water closet seat, white/cream, closed pattern with flat bottom, and cover and mild steel chromium plated or aluminium hinging device for pedestal pattern WC complete all as specified and as directed.

S&F 32 mm dia brass chromium plated bottle traps for wash basins with inlet and outlet screwed for pipe connection including necessary packing, union and cap fixed, in repairs, complete all as specified and as directed.

Taking down steel tubing and connections including cleaning for refixing or removal from site for 15mm bore pipe all as specified and directed .

Taking down steel tubing and connections including cleaning for refixing or removal from site for 20mm bore pipe all as specified and directed .

S&F 15mm bore tubes medium grade galvanized with all fittings such as sockets, elbows, unions, Tees & short pieces and fixed complete to walls and ceilings or laid in floors of any length all as specified and directed .

S&F 20mm bore tubes medium grade galvanized with all fittings such as sockets, elbows, unions, Tees & short pieces and fixed complete to walls and ceilings or laid in floors of any length all as specified and directed .

Taking down Chowkhats or frame with shutter (without taking off shutter from the frame) area exc 1.50 sqm but n.exc 4 sqm each and removal complete all as specified & directed.

Taking down Chowkhats or frame with shutter (without taking off shutter from the frame) area n.exc 1.50 sqm each and removal complete all as specified & directed.

S&F steel ventilator factory made with top hung shutter including hinges, steel peg stay complete all as specified and as directed.

S&F, in repair, Brass chromium plated mixer for wash hand basin for mixing hot and cold water screwed down for iron pipes suitable for 15mm bore pipe complete all as specified and directed.

S&F, in repair, 15mm bore stop valves/ Angle cock chromium plated screwed down high pressure with crutch or butter fly handles screwed both ends for iron pipe or for union complete all as specified and directed.

S&F, in repair, Bib taps, cast copper alloy with crutch or butterfly handle, sc-rewed down, screwed for iron pipe or for brass ferrule and fixed, 15 mm, fancy type, chromium plated fixed complete all as specified and directed.

S&F in repair chromium plated shower rose fancy type fixed to 15mm bore pipe complete all as specified and directed .

S&F vitreous china,coloured, counter top wash hand basin, oval type, size 550x400mm including cutting for and pinning in, but excluding waste pipecomplete all as specified and directed .

S&F PVC connection 15mm size with PTMT nuts, of length 450mm complete all as specified and directed .

S&F PVC connection 15mm size with PTMT nuts, of length 600mm complete all as specified and directed .

S&F, in repair, brass chromium plated tubular towel rail 20mm dia 'D' type 600mm long between flanges complete all as specified and directed .

S&F in repair CP brass soap tray/dish of approved make as approved by GE, complete all as specified and directed .

M&L for one coat of synthetic enamel paint on old decorative surfaces of steel over 10cm width or girth including preparation of surfaces complete all as specified and directed .

M&L for grinding and mirror polishing surfaces of old Kota/marble/granite stone flooring, skirting etc by hand or grinding machine, dusting off the surfaces after grinding, washing and mirror polishing complete all as specified and directed .

S&F galvanised MS wire cloth, 0.56mm nominal dia of wire and average width of aperture 1.18mm and fixed with tinned tacks, or galvanised wire staples complete all as specified and directed .

Taking down cement plaster etc on brick walls/ concrete (ceiling) surfaces of any descriptions including racking out joints, hacking for keys, scrubbing down with water and disposal of unserviceable materials to out side of MD land complete all as specified & directed.

M&L for rendering15 mm thick in two layers on external surfaces (10mm thick in CM 1:6 & 5mm thick in CM 1:4 mixed with liquid waterfroofing compound as per Manufacturer's instructions), finished even and smooth without using extra cement complete all as specified & directed. . (Note :- Liquid WPC shall be measured and paid seprately as "Supply only".)

Supply only liquid water proofing compound ISI Marked, of make as approved by GE complete all as specified & directed.

M & L for 15 mm thick rendering on fair faces of brick work or concrete internal surfaces in CM in 1:6, finished even and fair without using etra cement complete all as specified & directed.

Cutting grooves in brick wall,75mm wide and 65mm deep and shaping horizontal face of groove with cement mortar 1:3 complete all as specified and directed. (Note :- Galvanised steel wire netting shall be measured and paid for separately under relevent items of this BOQ)

Taking down eaves gutter,rain water pipes of any size or pattern including all fittings etc complete all as specified and directed.

S&F, PVC (SWR) pipes 110mm bore single socketed, in any length with rubber ring joints, laid in trenches or in floors complete all as specified and directed.

S&F, PVC (SWR) pipes 75mm bore single socketed, in any length with rubber ring joints, laid in trenches or in floor complete all as specified and directed.

S&F PVC (SWR) bends ISI marked any radius of 110 mm bore with access door complete all as specified and directed.

Hacking out old broken glass (any thickness, size, quality or description) from wooden or steel frames glazed complete all as specified and directed .

S&F 3mm thick sheet glass ordinary quality and galzing with oil putty or wooden beads in squares n exc 0.50 Sqmtr in each pane complete all as specified and directed .

S&F 3mm thick figured glass pin head type and glazing with oil putty or wooden beads in squares n exc 0.50 Sqmtr in each pane complete all as specified and directed .

S&F galvanised steel wire of mesh size 12mm and 1.4 mm nominal dia of wire and fixed with tinned tack ,or galvanised wire staples, complete all as specified and directed . .

M&L for brick work with sub class 'B' fly ash bricks, straight or curved on plan exc 6m mean radius built in CM (1:6) complete all as specified & directed.

M&L for brick work with sub-class `B' fly ash bricks built in CM 1:4, straight or curved on plan to any radius, using old size bricks, in half brick thick wall etc. complete all as specified and as directed.

Dismantling brickwork or stone/boulder masonry, built in cement mortar or cement lime mortar including all quoins, arches, pillars, etc, but excluding ashlar facings, dressed stone-work and precast concrete articles complete all as specified and as directed.

M&L for complete removal of existing water proofing treatment from top of roof and canopies / chajjas of building including removal of debris out side MD land all as directed.

M&L Water proofing treatment on roof surface (Horizontal & Vertical surfaces) in following sequence through manufacturer / authorized applicator of the manufacturer including properly cleaning & drying the concrete surfaces complete :

10mm thick rendering over roof surfaces in CM 1:3 with using liquid water proofing compound as per manufacturer's instructions, finished even and smooth without using extra cement complete all as specified & directed. Note: WPC shall be measured and paid for separately as "Supply Only" under respective item of BOQ.

Cleaning of plastered roof surfaces and applying a coat of bitumen primer @ 0.30 kg/Sqm on top of dry surface of finished cement mortar plaster.

Laying unrolled over the bitumen coated surface, 3mm thick spun bonded non-woven polyester reinforced APP modified water proofing membrane weighing not less than 3.0 Kg/Sqm with minimum side over lap of 100mm and end over lap of 150 mm shall be sealed by flame as per manufacturer's instructions complete all as specified & directed. Note:- Suitable embedment of APP modified water proofing membrane shall be ensured into walls/parapet walls.

Applying a coat of bituminous aluminium paint @ 100gm/ sqm over non-accessible roof and blinding material such as dry sand @ 0.75Kg/ Sqm over & including a coat of hot air blown bitumen 85/25 grade conforming to IS-702 @ 1.20 kg/sqm over polymeric membrane complete all as specified & directed. Note- Bituminous aluminium paint shall be of same manufacturer as specified for polymeric water proofing membrane.

M&L for preparing old plastered or unplastered surfaces of walls and applying one coat of cement based paint complete all as specified and directed.

M&L for preparation of old decorated surfaces of ceiling including brooming down or steel wire brushing, scrapping down smoke soot, moulds, moss and efflorescent salts and trading oil and greasy spot and applying one coat of white wash complete all as specified & directed.

Roughening surfaces of old concrete floor by picking, sweeping clean and washing down with water to remove dust etc and brushing the old prepared surfaces of concrete floor with neat cement slurry @ 3.0 Kg of cement per Sqm complete all as specified and as directed.

M&L 40 mm thick PCC (1:2:4) type B-0 using 12.5mm graded crushed stone aggregate as in flooring, finished even and smooth without using extra cement complete all as specified and as directed.

M & L for heterogeneous sports vinyl flooring, 4.0 mm thick , single layered, for indoor playing area such as Badminton court , Hand ball/ volley ball courts etc and fixed as per Manufacturer's specifications incuding necessary marking of paint complete all as specified and as directed. ( Make : (i) M/s Ebaco India Pvt Ltd (ii) M/s Mondo Sports Flooring (iii) M/s Forbo Flooring Systems or Equivalent Make as approved by GE) ( Note : Contractor shall provide warranty of 5 Years. A sum equal to 5 % of quoted amount against this item shall be retained from the Final Bill of the contractor which shall be released after the expiry of warranty period. Alternatively, contractor may furnish FDR in favour of GE, for the aforesiad amount.)

Taking down carefully any type of old unserviceable point wiring copper or aluminium conductor (light, fan, socket, bell or power) point complete with fittings such as switches ceiling roses, lamp holders, sockets, fan regulators, call bell, light fittings with PVC conduit surface / concealed or wooden battens including sunken cast iron / pressed steel terminal boxes etc complete all as specified & directed.

Taking down existing exhaust/ ceiling fan of any size/ sweep for keeping in the safe custody and re-fixing/ re-hanging the same after repair work or as directed and connecting up the same with & including twin twisted copper flexible wire from ceiling rose to exhaust/ ceiling fan complete all as specified & directed.

Taking down old/unserviceable distribution board by disconnection of electric connection carefully SPN DBs/TPN DBs/ Main Switch including old unserviceable MCCBs/ MCBs, Isolators, etc complete all as specified and directed at site.

Taking down existing old/ unserviceable sub main wiring of any type and description, removal of teak wood batten/ PVC pipe/ PVC casing & caping complete all as specified and directed.

M&L for provision of sub main wiring with two runs of single core FRLS PVC insulated, unsheathed, multistranded copper conductor cable of size 1.50 sqmm drawn in and including rigid PVC conduit medium grade ISI marked not less than 20mm dia with its accessories, concealed type, including one run of single core FRLS PVC insulated, unsheathed, multistranded copper conductor cable of size 1.50 sqmm as earth continuity and cutting chases as per standard engineering practice & making good the disturbed surfaces as per existing finish complete all as specified & directed. Notes:- (i) Finished sub main wiring with two runs of 1.50 sqmm cable & one run of 1.50 sqmm cable alongwith PVC conduit and its accessories shall be measured and paid as one unit length. (ii) Connections of cables with MCBs or bus bars shall be done through appropriate size brass/copper thimbles. (iii) Colour coding for wiring/ bus bar/ main connection shall be followed .

M&L for provision of sub main wiring with two runs of single core FRLS PVC insulated, unsheathed, multistranded copper conductor cable of size 10.0 sqmm drawn in and including rigid PVC conduit medium grade ISI marked not less than 25mm dia with its accessories, concealed type, including one run of single core FRLS PVC insulated, unsheathed, multistranded copper conductor cable of size 10 sqmm as earth continuity and cutting chases as per standard engineering practice & making good the disturbed surfaces as per existing finish complete all as specified & directed. Notes:- (i) Finished sub main wiring with two runs of 10.0 sqmm cable & one run of 10 sqmm cable alongwith PVC conduit and its accessories shall be measured and paid as one unit length. (ii) Connections of cables with MCBs or bus bars shall be done through appropriate size brass/copper thimbles. (iii) Colour coding for wiring/ bus bar/ main connection shall be followed .

M&L for provision of sub main wiring with two runs of single core FRLS PVC insulated, unsheathed, multistranded copper conductor cable of size 6.0 sqmm drawn in and including rigid PVC conduit medium grade ISI marked not less than 25mm dia with its accessories, concealed type, including one run of single core FRLS PVC insulated, unsheathed, multistranded copper conductor cable of size 6 sqmm as earth continuity and cutting chases as per standard engineering practice & making good the disturbed surfaces as per existing finish complete all as specified & directed. Notes:- (i) Finished sub main wiring with two runs of 6.0 sqmm cable & one run of 6 sqmm cable alongwith PVC conduit and its accessories shall be measured and paid as one unit length. (ii) Connections of cables with MCBs or bus bars shall be done through appropriate size brass/copper thimbles. (iii) Colour coding for wiring/ bus bar/ main connection shall be followed .

M&L for provision of sub main wiring with two runs of single core FRLS PVC insulated, unsheathed, mutistranded copper conductor cable of size 4.0 sqmm drawn in and including rigid PVC conduit medium grade ISI marked not less than 20mm dia with its accessories, concealed type, including one run of single core FRLS PVC insulated, unsheathed, multistranded copper conductor cable of size 4 sqmm as earth continuity and cutting chases as per standard engineering practice & making good the disturbed surfaces as per existing finish complete all as specified & directed. Notes:- (i) Finished sub main wiring with two runs of 4.0 sqmm cable & one run of 4 sqmm cable alongwith PVC conduit and its accessories shall be measured and paid as one unit length. (ii) Connections of cables with MCBs or bus bars shall be done through appropriate size brass/copper thimbles. (iii) Colour coding for wiring/ bus bar/ main connection shall be followed .

M&L for provision of sub main wiring with two runs of single core FRLS PVC insulated, unsheathed, mutistranded copper conductor cable of size 2.50 sqmm drawn in and including rigid PVC conduit medium grade ISI marked not less than 20mm dia with its accessories, concealed type, including one run of single core FRLS PVC insulated, unsheathed, multistranded copper conductor cable of size 2.50 sqmm as earth continuity and cutting chases as per standard engineering practice & making good the disturbed surfaces as per existing finish complete all as specified & directed. Notes:- (i) Finished sub main wiring with two runs of 2.50 sqmm cable & one run of 2.50 sqmm cable alongwith PVC conduit and its accessories shall be measured and paid as one unit length. (ii) Connections of cables with MCBs or bus bars shall be done through appropriate size brass/copper thimbles. (iii) Colour coding for wiring/ bus bar/ main connection shall be followed .

M&L for point wiring concealed type with 1.50sqmm PVC insulated, unsheathed, single core, multistranded copper conductor FRLS cable 1100 volts grade including 1.5sqmm PVC insulated unsheathed multistranded copper copper conductor FRLS cable as earth continuity conductor drawn through in and including rigid PVC conduit not less than 20mm dia with its accessories, sunken type pressed steel terminal box made of 1.2mm thick MS sheet/ anodised steel box painted with one coat of red oxide primer including 3.0mm thick ISI marked laminated/ ebonite sheet cover for fixing switches/ socket/ regulators etc including all fixing accessories and cutting chases as per standard engineering practice & making good the disturbed surfaces as per existing finish complete all as specified & directed.

One light point controlled by one switch 5 Amp.

One fan point/exhaust fan controlled by one switch 5 Amp.

One socket point 3/5pin controlled by one switch 5 Amp on same board.

One socket point 3/5 pin controlled by one switch 5 Amp on Independent board.

M&L for point wiring concealed type with 2.50sqmm PVC insulated, unsheathed, single core, multistranded copper conductor FRLS cable 1100 volts grade including 2.5sqmm PVC insulated unsheathed multistranded copper conductor FRLS cable as earth continuity conductor drawn through in and including rigid PVC conduit not less than 20mm dia with its accessories, sunken type pressed steel terminal box made of 1.2mm thick MS sheet/ anodised steel box painted with one coat of red oxide primer including 3.0mm thick ISI marked laminated/ ebonite sheet cover for fixing switches/ socket/regulators etc including all fixing accessories and cutting chases as per standard engineering practice & making good the disturbed surfaces as per existing finish for the one socket out let 3/6 pin, 15/16 Amps controlled by one no one way piano type switch on independent board complete all as specified & directed.

M&L for Point wiring with PVC insulated 1.5 sq mm multi stranded copper conductor cable FRLS 1100 volts grade drawn into existing conduit not less than 20mm (ISI marked) including all fitting and fixing accessories including sunk in cast iron/pressed steel terminal boxes duly painted with two coats of antirorrrosive paint outside and two coats of aluminium paint inside, 2.8mm thick hylam brand laminated white bakelite sheet cover for mounting of switches, sockets, fan regulators etc and PVC insulated 1.5 Sqmm multistranded copper conductor cable as earth wire complete all as specified and directed for the followings :

One light point controlled by one switch 5 Amp.

One fan point/exhaust fan point controlled by one switch 5 Amp.

One socket point 3/5 pin controlled by one switch 5 Amp on the same board.

One socket point 3/5 pin controlled by one switch 5 Amp on Independent board.

M&L for point wiring concealed type with 2.50sqmm PVC insulated, unsheathed, single core, multistranded copper conductor FRLS cable 1100 volts grade including 2.5sqmm PVC insulated unsheathed multistranded copper conductor FRLS cable as earth continuity conductor drawn into existing conduit not less than 20mm dia with its accessories, sunken type pressed steel terminal box made of 1.2mm thick MS sheet/ anodised steel box painted with one coat of red oxide primer including 3.0mm thick ISI marked laminated/ ebonite sheet cover for fixing switches/ socket/regulators etc including all fixing accessories and cutting chases as per standard engineering practice & making good the disturbed surfaces as per existing finish for the one socket out let 3/6 pin, 15/16 Amps controlled by one no one way piano type switch on independent board complete all as specified & directed.

M&L for modular fan regulator socket type AC 230 volts complete all as specified and directed .

M&L for Switch piano flush type AC 230 volts 5 Amps single pole one way complete all as specified and directed .

M&L for Socket outlet 3 pin, 5 Amps and AC 230 volts flush type complete all as specified and directed .

M&L for Switch socket combination 3 pin 5 and 15 Amps AC 230 volts flush type complete all as specified and directed .

M&L for Ceiling rose surface bakelite 65 mm x50 mm three terminal AC 230 volts flush type complete all as specified and directed .

S&F in replacement LED light fitting, square 57x57 CM, Not less than 36 Watt along with fixtures, Surface / Recessed /Pendent mounting LED luminaires with diffuser channel, connector block, etc . complete with all accessories internally pre-wired and including round wood block, connecting up with three core flexible copper conductor cable of suitable size and length complete all as specified and directed. (Make: Philips cat part no: RC375B LED 36S PSU W60L60 S2 WH or equivalent in Luker/Havells as approved by GE)

Supply & Fixing Smart bright Batten Series, LED luminaire using LED 22 watt 110 Lumens/watt with diffuser which ensures uniform distribution and comfort, batten series features latest LEDs and delivers consistent light output, stable color start Extruded Aluminium housing, Energy efficient, Flicker free start Inbuilt driver unit, Suitable for wall and ceiling mounting using brackets with and including the luminaire testing on completion as per Standard Specification IEC 60598-2-1 / IS: 10322(Parts/Secl), (Make : Philips Cat part No BN 021 LED 22S 6500/4000 PSU GR S1 or Equivalent as approved by GE)

S&F , in replacement, single pole and neutral sheet metal enclosures with two pin & earth plug and socket complete with and including one number single pole MCB of 20 Amps complete all as specified and as directed.

S & F Sheet metal enclosure for DBs, Single Pole and Neutral, 8 way with 200 Amps rated bus bar, 240 volts, double door complete all as specified and directed .

S & F Sheet metal enclosure for DBs, Single Pole and Neutral, 12 way with 200 Amps rated bus bar 240 volts , double door, complete all as specified and directed .

S & F MCB single pole and neutral 240 volts 40 Amps, 'B' Series complete all as specified and directed .

S & F MCB single pole, 240 volts, 6 to 40 Amps, 'B' Series complete all as specified and directed .

Supply & fix, in replacement , LED Security Light Luminaire 45 watt 6000K with high power LED cool white,CRI 75+ 5% supply voltage 220/240/50 Hz, light engine driver base.pole adapter,powder coated pressure die cast aluminium with heat resistant toughened glass with lens type, with and including mounting bracket made out of GI pipe 40 mm dia, medium Grade, not less than with 1.2 m.long in any shape with 2 nos of pole fitting clamps made out of MS flat , nuts and bolts and painting with aluminium paint. complete all as specified and as directed.

S&F Sheet metal enclosure for MCB distribution board including 200 Amps bus-bar, Triple Pole and Neutral 415 V, 4 Ways, double door type,complete all as specifide and directed.

S & F MCB TPN 25 to 63 Amps, 240 Volts, rupturing capacity 10 KA, "B" series,and to be housed in DBs catered here in before complete all as specified and directed . (Note :- Proper and suitable size cable copper lugs to be fixed with MCBs are included in unit rate of each MCB of any rating)

Supply, fixing and connecting highbay light fitting suspended with roof, 70 Watt complete, pressure die cast aluminium housing with high power LED as lighting source , with IP66 and IK 08 protection and impact resistance complete all as specified and directed.

Supply and fix Single phase propeller type Exhaust fan heavy duty AC 230 volts 300 mm sweep, metallic body complete with Metalic louvers and shutters including electric connection with PVC flexible twin core copper wire from ceiling rose to Exhaust fan, nut & bolt complete all as specified and as directed.

Supply, fixing and connecting 100 Watt LED flood light , Energy saving and environmental friendly long life LED flood light made up of pressure die cast aluminium housing with high power LED as lighting source , with IP66 and IK 08 protection and impact resistance complete all as specified and directed.

S & F ON LOAD Change over switch 200 Amps 415 volts in sheet metal enclosure 4 pole including necessary provision for inserting cable ,complete all as specified and as directed.

M&L for earthing complete with galvansided steel earth plate electrode 600x600x6.0mm thick directly burried in the ground (earth pit not less than 2.25M deep below ground level) with top edge of earth plate not less than 1.50M deep below normal ground level, connected to galvanised iron wire 4mm by means of bolts, nuts, check nuts and washers of galvanised iron or steel, 15mm bore GI pipe medium grade including necessary fittings for protection of earthing wire, watering pipe 20mm bore GI medium grade, concrete chamber in PCC (1:4:8) type D-2 using 40 mm grade aggregate, coping shall be in PCC (1:3:6) type C-1 using 20 mm grade aggregate and internal surfaces of concrete chamber shall be given 12mm thick plaster in CM (1:4), funnel with wire gauge of 22 gauge (0.63 mm) 8 mesh per linear including 50mm thick cover of RCC (1:2:4) type B-1 using 20mm grade stone aggregate reinforced with 8mm MS deformed bar @ 75 mm C/C both ways, char coal dust and common salt all as shown in electrical plate No. 3 of SSR Part-I (2009) including all necessary excavation & earth work and removal of surplus soil to a distance n. exc 50M and providing connection points with MS/ GI bolts & washers as required and connection from earth test point to earth electrode with same GI earth wire alongwith protection pipe and testing on completion complete all as specified and directed. Note:- GI wire and protection pipe from earth electrode to test point max upto 7.50M shall be deemed to be included in the unit rates as quoted by the contractor.

Supply and laying or fixing or passing in trenches/ on pole/ through pipes, 1100 volts grade XLPE insulated, screened PVC bedded, galvanised steel strip or wire armoured, heavy duty electric cable with stranded aluminium conductor of cross section area 35 sqmm, 3.5 core including jointing materials such as cable glands & lugs etc Complete all as directed. ( Note : Excavation and earthwork, sand cushioning and cable protection will be measured and paid for separately)

Excavation in trenches, not exceeding 1.5m wide and not exceeding 1.5m in depth for foundation, for laying of pipe, cable etc or n. exc.10 Sqm on plan and n. exc. 1.5m in depth for shafts, cesspits, manholes, pier holes, etc and getting out in any type of soil complete all as specified and directed.

Drilling (Horizontally) to existing road (maximum 10M wide) suitable for passing GI tubing of dia upto 80mm/ 100mm as required at site complete all as specified and directed. Note:- All necessary T&P required at site for drilling shall be arranged by contractor at his own cost and quoted rate shall be deemed to be included for all these provisions and nothing extra shall be paid on this account.

Returning , filling in, including spreading, leveling, watering and well ramming in layers not exc 25 cm complete all as specified and as directed.

Removing excavated material n exc 50m and depositing where directed at a level n exc 1.5m above the starting point complete all as specified and as directed.

Supply and laying sand cushioning to under ground cable in trenches/ existing cable trenches/ducts, in layers of 8 cm deep before laying the cable and 15 cm deep after laying and stretching the cable complete all as specified and directed . ( Note : Punned thickness shall be measured for payment)

Supply and laying brick covering with width equal to length of brick as mechanical protection to cable with well burnt sub class 'B' bricks laid dry flat complete all as specified and directed .

M& L for GI Tubes, of size 40 mm dia light grade, galvanised, with all fitting, laid in trenches for protection of cable in road, drain crossing complete all as specified and as directed.

Schedule of credit amount of Rs. 69,255.00 to be deducted during AOC

Rai Construction Co