Improvements of Water Supply Scheme to Kamayagoundanpatti Town Panchayat, Theni District under AMRUT 2.0 Scheme

Amount

1. Earthwork excavating and depositing on bank with an initial lead of 10m & initial lift of 2m in sand silt other loose soil, wet sand or silt not water,Light black cotton soil, sandy loam, hard stiff clay, stiff black cotton, hard red earth shales, muram, graverl stoney earth & earth mixed with small size boulders & hard gravelly soil as per S.S 20B

Earth work excavation for foundation and depositing on bank with in the initial lead of 10m and a lift of 2m in Soft disintegrated rock, Laterite, Soft rock or Kankar, not requiring blasting etc., as per SS 20 A.

2m-4m depth

4m-6m depth

Cutting Open roads

Labour for cutting open road for laying water mains or sewer

i) B.T. Roads (or) Maccadam road

ii) Concrete Roads

Earth work excavation for water supply work- Ordinary Soil - such as Hard stiff clay, stiff black cotton, hard red earth, shales, murram gravel, stoney earth and earth mixed with small boulders and hard gravelly soil etc.,

100 mm DI K9

150 mm DI K9

200 mm DI K9

250 mm DI K9

300 mm Di K9

HDPE Pipes of 90 mm diameter

HDPE Pipes of 110 mm diameter

HDPE Pipes of 140 mm diameter

HDPE Pipes of 160 mm diameter

HDPE Pipes of 180 mm diameter

HDPE Pipes of 200 mm diameter

HDPE Pipes of 250 mm diameter

HDPE Pipes of 315 mm diameter

Plain Cement Concrete 1:4:8 Mix (one part cement, four part sand and Eight part of aggrigate) using 40 mm size ISS HBG metal from approved quarry including cost and conveyance of all materials to site. Loading and unloading charges and labour charges for mixing. Laying and curing etc., complete as per TNDSS NO : 28 & VI (S2) VI (S5A) VII standard specifications as directed by Engineer incharge.

Plain Cement Concrete 1:2:4 Mix (one part cement, two part sand and four part of aggrigate) using 20mm size ISS HBG metal machine crushed from approved quarry including cost and conveyance of all materials to site, loading and unloading charges and labour

9. Provding and laying in position, Standardised concrete Mix M-25 Grade in accordance with IS 456-2000, using 20mm and down graded hard broken granite water cement ratio of 0.50, including admixture (plasticiser/ super plasticiser) in recommended proportions as per IS:9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability with about (5.0 cu.m) 7730 kg. of 20mm machine crushed stone jelly and with about (3.3 cu.m) 5156 kg of 10-12mm machine crushed stone jelly and with about (4.79 cu.m) 7670 kg of sand, but excluding cost of reinforcement grill and fabricatingcharges, centering and shuttering and also including laying, vibrating with mechanical vibrators, finishing, during, etc. complete complying with standard specification and as directed by the departmental officers. The coarse and fine aggregates to be used should comply with the requirements os IS Standards (No separate payment will be made by the Department for the excess usage of materials).

1.5 m to 4.5 m below G.L

UPTO G.L

Above G.L upto 4.50m height

Above 4.50m to 7.32m ht., from G.L

Above 7.32m to 10.98m ht., from G.L

Above 10.98m to 14.64 ht., from G.L

Above 14.64m to 18.30 ht., from G.L

14. Providing and laying in position Standardised concrete Mix M-30 Grade in accordance with IS:456-2000, using 20mm and down graded hard broken granite stone jelly for all RCC items of works with minimum cement content of 400 kg/m3 and maximum water cement ration of 0.45, including admixture (plasticiser/ super plasticiser) in recommended proportins as per IS:9103 to acceierate, retard setting of concrete, improve workanility without impairing strength and durability with about (5.0cu.m) 7730kg of 20mm machine crushed stone jelly and with about (3.3 cum ) 5156kg of 10-12 mm machine crushed stone jelly and with about (4.79 cu.m) 7670kg of sent, but excluding cost of reinforcement grill and fabricating charges, centering and shuttering fixtures lide fan clamps in the RCC floor/ roof slabs wherever necessary without claiming extra, etc., complete complying with standard specification and as directed by the departmental officers. The coarse and fine aggregates to be used should comply with the requirements of IS Standards. (No separate Payment will be made by the Department for the excess usage of materials)

1.5 m to 4.5 m below G.L

0-1.5m Below GL

0 to 4.5m above GL

15. Provding and laying in position, Standardised concrete Mix M-20 Grade in accordance with IS 456-2000, using 20mm and down graded hard broken granite water cement ratio of 0.55, including admixture (plasticiser/ super plasticiser) in recommended proportions as per IS:9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability with about (5.0 cu.m) 7730 kg. of 20mm machine crushed stone jelly and with about (3.3 cu.m) 5156 kg of 10-12mm machine crushed stone jelly and with about (4.79 cu.m) 7670 kg of sand, but excluding cost of reinforcement grill and fabricatingcharges, centering and shuttering and also including laying, vibrating with mechanical vibrators, finishing, during, etc. complete complying with standard specification and as directed by the departmental officers. The coarse and fine aggregates to be used should comply with the requirements os IS Standards (No separate payment will be made by the Department for the excess usage of materials).

Centering for sides and soffits of R.C.C slab of plane surface for R.C.C floor slab including strutting upto 3.3 mt height using MS sheets of size 90cmx60cm and stiffend with welded MS angle of size 25mmx25mmx3mm laid over silver oak (country wood) joist

Plane Surface

3.30 - 4.30M above GL

4.3M to 5.30m above GL

5.30m- 6.30m above GL

6.30m- 7.30m above GL

7.30m- 8.30m above GL

9.30m -10.30 above GL

10.30 - 11.30M above GL

11.30 - 12.30M above GL

14.30 - 15.30M above GL

15.30 - 16.30M above GL

Square Column

3.30 - 4.30M above GL

4.30 - 5.30M above GL

5.30 - 6.30M above GL

6.30 - 7.30M above GL

7.30 - 8.30M above GL

8.30 - 9.30M above GL

9.30 - 10.30M above GL

10.30 - 11.30M above GL

11.30 - 12.30M above GL

12.30 - 13.30M above GL

13.30 - 14.30M above GL

14.30 - 15.30M above GL

15.30 - 16.30M above GL

Curved Surface

Circular Column

3.30 - 4.30M above GL

4.30 - 5.30M above GL

5.30 - 6.30M above GL

6.30 - 7.30M above GL

7.30 - 8.30M above GL

8.30 - 9.30M above GL

9.30 - 10.30M above GL

10.30 - 11.30M above GL

11.30 - 12.30M above GL

12.30 - 13.30M above GL

13.30 - 14.30M above GL

14.30 - 15.30M above GL

15.30 - 16.30M above GL

Brick Work

Brick Work in Cement Mortar 1:5 Mix (one cement, five sand) using new best II Class Ground Mould chamber Bricks of size ( 9” x 4 3/8” x 23/4 “ )from approved quarry including cost and conveyance of all materials to site. Loading and unloading charges and labour charges for mixing, laying and curing etc. complete. Complying with std. specifications.

First Floor

Second Floor

Plastering

Plastering with CM 1:5(one cement and three sand) 20mm thick including cost of materials, labour charges for finishing, curing etc., complete and as directed by Departmental Officers

Plastering with CM 1:3(one cement and three sand) 10mm thick including cost of materials, labour charges for finishing, curing etc., complete and as directed by Departmental Officers

B) Finishing the top of roof with one course of machine pressed tiles 23 C.m x 23 C.m x 2 C.m size using cement mortor 1:3 mix mixed with 2% by weight of Crude Oil and pointing with Cement Mortor 1:3 mix Cost of all materials and labour charges and brick

Painting

Exterior Emulsion paint Two coats with good quality of approved Emulsion paint including cost of all materials to site and all labour charges for mixing applying and proper curring etc., Complete as per Standard Specifications for 10 sqm

Painting Two Coats on new Iron works with best synthetic enamel paint of approved colour and quality – 10m2.

Steel Reinforcement

Supplying fabricating and placing in position of RTS road at all heights for reinforcement including cost of steel for all works and labour charges including cost of binding wire etc., complete for all RCC works and as directed by Departmental Officers

Supply and fixing of M.S Grill Gate with one coat of Red oxide with Primer including all costs such as welding,grinding and fabrication charges, cost and conveyance of all materials to site etc,complete as per standard specification.

Rolling Shutter

Supply and fixing of Rolling shutter of Size 2.5m *2.5m Manually operated with necessary appliances and as directed by Departmental Officers

Window

Supply and Delivery Fabrication of MS doors and windows with outer frame and shutter frame in MS angle of size 40mm x 40mm x 6 mm with MS flat 25mm x 25mm x 6mm and MS sheet of 18 gauge including ventilating arrangements using 20mm square MS rods with locking arrangements including two coats of approved enamel paint over coat of red oxide including cost of angles, plates, sheets, fabrication charges, cost of hold fast and transportation charges etc., complete.

Ventilator

Supply and Fixing of Steel galzed ventilators of the N type of Size 0.45 m x 0.60 m fabricated with 35*20*4.0m Ms Flats wherever necessary includings all fixtures and appliances as per Standard Specification and as directed by departmental officers

MS ladder 12m Stagging height

Manhole

Supplying and fixing in position C.I. Manhole covers (light or heavy duty) of 600mm X 600mm sizes of best approved quality and as per standard specifications etc., complete.

CI Steps

Provision for CI Steps to be placed in Staggered manner including fixing etc complete and as directed by departemental officers

Crane

2T capacity hand operated over head Travelling(HOT) crane suitable for a span upto 6 Mtrs, andtravel length upto 10 Mtrs. with clear lift upto 6 Mtrs.including gear type chain pulley block with GI chainand geared Travelling trolley complete with allaccessories including girder

Lock & key

Provision for Shell with lock and Key arrangements to Keep the log Book Tools etc and as directed by Departmental officers

RCC Inside Ladder

Supply and fixing in position of R.C.C.(1:1.5:3) pre-cast ladder of length 4m with vertical post of size 0.1 x 0.15m and step size of 25x25mm with 45cm width for inside the tank using hard broken stone jelly and river sand including the cost of reinforcement grills and fabrication charges moulding, curing, finishing charges and fixing in position neatly complying with standard specification and as directed by the Departmental Engineer etc. complete

Cut Stones

Providing cut stone set in CM 1:3 (one cement and three sand) using well dressed cut stone supporting inlet pipe of size 0.30 x 0.30 x 0.15m for service reservoir etc., complete as per standard specifications and as directed by Engineer-in-charge.TWAD SOR

OHT Ventilator

AC Cylindrical Cowl

Forming Ring Bund

Forming Ring bund using sand bags filled with filling sand stiching the bags with jute coir conveing the stiched sand bags to preached site and forming the ring bund by placing the stiched sand bags in proper position , packing tightly and blocking the joints with clay and straw leaves to arrest the leakage as stated by departmental officers including the cost of empty cement bags, sand, jute coir complete for 2.83 cum.

Flooring

Providing Granolythic floor finish of the 25mm thickness with PCC 1:2:4 using 10 to 12mm hard broken stone jelly etc.- 1 Sqm

WTP - Flooring

Paving the floor with design Antiskirt ceramic tiles (colour and shade as directed) of size 305 mm x 305mm x 6 mm in all floors over a base layer of cement mortar 1:3 (one cement and three sand ) 20mm thick laid in-situ and pointed with same coloured ceme

WTP - Dadoing

Dadooing walls with Glazed tiles of sizes 305mm X200mm X 6mm size of approved make and quality and colour l Set in cement mortar 1:2 (one cement ,two sand) over 10 mm base layer plastering and pointing with white cement neatly as directed.

WTP - Water Level indicator

Supply, delivery and fixing in position of water level indicator with float of approved pattern for inner and outer compartments including cost of materials etc. and as directed by the Dept. officers.

Solid PVC door shutters using 19 Gauge 19mm MS square tubes for styles and outer frames. 15mm MS square tubes for top, lock and bottom rails. The steel tubes shall be covered with 5mm thick solid PVC sheets. Shutter using 5mm thick solid PVC sheets for panelling shall rigidly fixed in position including necessary furniture and fittings. The over all size of styles shall be 50mm x 30mm. The over all size of top rail, Lock rail and bottom rail shall be 75mm x 30mm. The over all size of frames shall be 50mm x 45mm, with suitable rabate for housing the shutter.

Barricading Work

Barricading work (Where the lines are in narrow width of municipality area,busy streets like Market, Bus-stand and in the Highways etc.) for laying ofpipe line using casurina poles at 1.50m center to center (8cm to 10cm dia.and 1.80m height) vertical with horizontal poles in two rows, painting thevertical poles in the road facing sides with ready mix paint, tying the vertical and horizontal poles with coir rope including supplying, delivery and fixing of GI sheet (0.90m x 0.8mm thick) in the horizontal poles and fixing75mm dia. reflectors including earth work excavation for fixing verticalposts and finally removing and stacking the materials safely for further useetc., complete and as directed by TWAD Board officers.

Traffic

Non Traffic

Lowering DI Pipes

Lowering of D.I Pipes and specials in the trenches and laying to proper grade and alignment and as directed by the TWAD Officers.

100 mm DI K9

150 mm DI K9

200 mm DI K9

250 mm DI K9

300 mm Di K9

100 mm DI K7

250 mm DI K7

Lowering HDPE Pipes

Lowering the following pipes and specials into trench and laying to proper grade and alignment complete as per standard specifications and as directed by the Departmental Engineer.

HDPE Pipes of 90 mm diameter

HDPE Pipes of 110 mm diameter

HDPE Pipes of 140 mm diameter

HDPE Pipes of 160 mm diameter

HDPE Pipes of 180 mm diameter

HDPE Pipes of 200 mm diameter

HDPE Pipes of 250 mm diameter

HDPE Pipes of 315 mm diameter

HDPE 50 mm PN6

Jointing Di pipes

Jointing the C.I/ D.I-S/S pipes and specials with neat cement or cement mortar and spun yarn including caulking the joints, curing. (including cost of jointing material

100 mm DI K9

150 mm DI K9

200 mm DI K9

250 mm DI K9

300 mm Di K9

100 mm DI K7

250 mm DI K7

Jointing HDPE Pipes

Jointing HDPE Pipes and Specials by butt fusion welding / electro fusion welding joints using fusion equipment as per ISO 21307-2011 and as per IS 7634 (part-2) : 2012 including cost of hire charges for butt fusion equipment power supply arrangements etc.

90 mm diameter (50.0m length for 1 Nos of Joints )

110 mm diameter (50m length for 1 Nos of Joints )

140 mm diameter (6.0m length for 1 Nos of Joints )

160 mm diameter (6.0m length for 1 Nos of Joints )

180 mm diameter (6.0m length for 1 Nos of Joints )

200 mm diameter (6.0m length for 1 Nos of Joints )

250 mm diameter (6.0m length for 1 Nos of Joints )

315 mm diameter (6.0m length for 1 Nos of Joints )

HDPE 50 mm PN6

Testing pipes

Testing of D.I/HDPE pipes for water supply with hydraulic testing equipment by filling with water (including cost of water @ Rs. 60/KL) and testing to recommended pressure in convenient stretches and attending the bursts if any occured during the test, excluding the cost of pipes but including other incidential and operational charges etc., complete for the following diametres of pipes.

100 mm DI K9

150 mm DI K9

200 mm DI K9

250 mm DI K9

300 mm Di K9

HDPE Pipes of 90 mm diameter

HDPE Pipes of 110 mm diameter

HDPE Pipes of 140 mm diameter

HDPE Pipes of 160 mm diameter

HDPE Pipes of 180 mm diameter

HDPE Pipes of 200 mm diameter

HDPE Pipes of 250 mm diameter

HDPE Pipes of 315 mm diameter

100 mm DI K7

250 mm DI K7

HDPE 50 mm PN6

Refilling Trenches

Refilling or backfilling trenches with excavated soil after pipe laying in layers not exceeding 20 cm in depth, ramming and consolidation of each layer, watering etc. all complete as per standard specifications and as directed by the Departmental Engineer

100 mm DI K9

150 mm DI K9

200 mm DI K9

250 mm DI K9

300 mm Di K9

HDPE Pipes of 90 mm diameter

HDPE Pipes of 110 mm diameter

HDPE Pipes of 140 mm diameter

HDPE Pipes of 160 mm diameter

HDPE Pipes of 180 mm diameter

HDPE Pipes of 200 mm diameter

HDPE Pipes of 250 mm diameter

HDPE Pipes of 315 mm diameter

Construction of Brick work valve Chamber with M20 Grade concrete . The rate should include earth work excavation in various soils met with at the site of work, refilling the pit after the construction of the pit, PCC M10 for Blinding Concrete, Brick work in CM 1:5 and plastering with CM 1:5 - 12mm thick, cost of steel reinforcement fabrication charges, Cover slab with manhole cover etc., and fixing the valves in position inside the pit including laying, jointing of valves, HDPE pipes and specials including the cost of jointing materials such as bolts and nuts RI sheets washers etc., complete and as directed by the Departmental Engineer.

Construction of RCC spiral staircase in RCC M25 (one cement, one and half sand, three aggregates) using 20mm HBGS of 1.80m diameter of required height for approach to the roof of service Reservoir with RCC handrails including earthwork excavation, providing CC 1:4:8 mix, RCC footing 1:1.5:3 mix, GL platform etc., and also including cost of steel reinforcement, fabrication charges, scaffolding, centering, precasting charges, cement, painting etc. complete as per standard specifications and as directed by Engineer, The staircase shall be braced to the column of service reservoir at suitable interval. (in the BOQ, quantity column the exact height to be mentioned from GL to roof slab bottom to get total value of work to be done.

DI Pipes

Supplying of K9 DI Pipe of dia following dia, conforming to IS 8329-2000 including all local and central taxes , transportation, freight charges, loading and unloading, conveyance to site and stacking the same, cost of all labour, material & etc complete.

100 Mm DI K7

250 Mm DI K7

100 mm DI K9

150 mm DI K9

200 mm DI K9

250 mm DI K9

300 mm DI K9

HDPE Pipes

Supplying of HDPE pipe of PE 100 grade, PN -6 class conforming to IS 4984 including all local and central taxes , transportation, freight charges, loading and unloading, conveyance to site and stacking the same, cost of all labour, material & etc complete

HDPE 50mm PN

HDPE Pipes of 90 mm diameter

HDPE Pipes of 110 mm diameter

HDPE Pipes of 140 mm diameter

HDPE Pipes of 160 mm diameter

HDPE Pipes of 180 mm diameter

HDPE Pipes of 200 mm diameter

HDPE Pipes of 250 mm diameter

HDPE Pipes of 315 mm diameter

DI Specials

Supply & Delivery to site of all types of specials such as Tees, Tapers. Bends, endcaps etc as per specification.

DI Specials 100- 200 mm dia

HDPE Specials

Supply & Delivery to site of all types of specials such as Tees, Tapers. Bends, endcaps etc as per specification.

HDPE bends

HDPE Tees

HDPE bends

HDPE Tees

HDPE bends

HDPE Tees

HDPE bends

HDPE Tees

HDPE bends

HDPE Tees

HDPE bends

HDPE Tees

HDPE bends

HDPE Tees

HDPE bends

HDPE Tees

DI Valves

Supply and delivery of DI D/F Gate sluice valves (soft seated) resilient seated soft sealing Gate Valves(Sluice Valves) with body Bonnet of Ductile cast iron ofGrade GGG 40 or equivalent grade,Wedge fully rubber lined with EPDM replaceable spindle nut without gland packing and with 3 ORing protection on the shaft and seals of NBR and the valves should be of Vacuum tight and 100% leak proof with face to face dimensions as per BS 5163-89/ISI 4846-2000/DIN 3202 F4. All the valves should be with electrostatic powder coating both inside and out side with pocket less straight through body passage. All the valves are to be compatible for buried application withpressure rating PN 10/16

100 mm DI Sluice Valve

150 mm DI Sluice Valve

200 mm DI Sluice Valve

300 mm DI Sluice Valve

100 mm DI Scour Valve

200 mm DI Scour Valve

300 mm DI Scour Valve

100 mm DI NRV

300 mm NRV

50 mm Air valve

150 mm Flow Control Valve

200 mm Flow Control Valve

250 mm Flow Control Valve

300 mm Flow Control Valve

100 mm CI Butterfly Valve

250mm CI Butterfly valve

450 mm CI Butterfly valve

15 mm CI Ball Valve

Flow Meter

Electromagnetic Flow Meter shall be a velocity sensing Electromagnetic type, microprocessorbased signal converter, sealed housing, flanged tube meter for 1.0 Mpa working pressure,manufactured to highest standard available for mag-meters, equipped with minimum six digitdigital totalizers, reading in different units (Kiloliters / Cubic meter) and shall be accurate within0.5% of Measured value, shall operate within a range of 0.3 m/sec to 4 m/sec and beconstructed as follows: Meter tube (Sensor) shall be fabricated from stainless steel tube and useclass PN10 flat face carbon steel flanges in accordance with IS 1538. These flanges shall bewelded to the flow tube. The internal and external of the meter tube shall be blasted to nearwhite and lined with hard rubber/ Polyurethrene/ PTFE preferably by SBR or EPDM. Meter tubeshall have a constant nominal inside diameter offering no obstruction to the flow. The accuracyshould be inclusive of linearity, hysteresis, repeatability, temperature and pressure effects. CoilHousing shall be fabricated from stainless steel (SS304)/ Die cast Aluminium/ Carbon steel withanticorriosive paint for corrosion resistance and welded to the tube providing a completely sealedenvironment for all coils, electrode connections and wiring harness capable of submerged orburied operation with IP68 Protection. Signal Converter shall be pulsed DC coil excitation typewith auto zeroing. The signal converter shall be remotely mounted away from the meter. Theconverter shall indicate direction of flow and provide a flow rate indication and a total of flowvolume for both forward and reverse directions. The converter shall provide an isolated 4-20 mAoutput into minimum 500-ohm load and a frequency output of a maximum of 0-10 KHZ and ascaled pulse output. The microprocessor based signal converter shall have a self-diagnostic testmode and a backlit display that continuously displays “Rate of Flow” and “Total Volume”.Converter shall be supplied with a programmable low flow drop out, higher flow and empty pipezero return. The signal converter housing should be die-cast aluminum with glass window. Theconverter cum transmitter should be fully programmable from the front facia. The programmingshould be user friendly, self-prompting menu driven. Flow meter test calibration certificate fromFCRI, flow test lab / NABL accredited lab to be furnished.

OHT Pipe Connection

Supply and delivery of 150mm dia C.I D/F Pipe The rate shall inclusive of all charges such as materials and loading, unloading, transportation charges and all taxes etc, complete as per standard specification.

150 mm CI Pipe

250 mm CI Pipe

Intake Well Pipe

Supply, delivery & fixing of CI Pipes & Specials for the Drawl of Water into the well including labour Charges etc.,

300 mm dia DI Pipes 2.00m Length

300 mm Valve Specials

300 mm dia DI Bend

Supply, Delivery & Fixing of the Following size of Sluices Values manually operated with gear arrangements including all allied works

300 mm DI Sluices values

Provision for Wire Mesh to Prevent entry of Silt

Supply, of following electromechanical items required for 4 MLD water treatment plant including the cost of transportation, installing and commissioning.

Flash Mixer

Intake Screen

Flash Mixer Drive + Motor

Flash Mixer Mechanism

Flocculator

Flocculator Drive + Motor

Flocculator walkway - Common for Flash Mixer and Flocculator

chlorination Dosing Pump

Dosing pump

Agitator for Dosing Tank

Dosing Tank

Alum Dosing Pump

Dosing pump

Agitator for Dosing Tank

Dosing Tank

Clarifier

Clarifier Drive + Motor

Clarifier Mechanism

Sludge Transfer Pump

Sludge Transfer Pump - Semi Open Impeller

Filtration System

Filtration Nozzles

Filtration Underdrain System

Gravel

Air Blower

Air Blower

Air Blower Drive Motor

Base Frame and Accessories including fasters

Acoustic Hood

Filter Press

Filter Press

Supply, of following Laboratoty instruments, Glass Wares and Chemicals required for 4 MLD water treatment plant including the cost of transportation, installing and commissioning.

Level Indicator Transmitter

pH Indicator

Flow Transmitter - Inlet Pump

Flow Transmitter - Backwash Line

Flow Transmitter - Product Water Line

Turbidity Analyzer and Indicator

Supply, of following Laboratoty instruments, Glass Wares and Chemicals required for 4 MLD water treatment plant including the cost of transportation, installing and commissioning.

pH/ ORP Meter

pH Solution - 4

pH Solution -7

pH Solution -10

Cleaning Solution for General Purpose 500 ml

Electrode storage solution 500 ml bottle

ORP test solution @ 200/ 275 mV

ORP test solution @ 240 mV

ORP test solution @ 470 mV

Portable EC/Resistivity/ TDS/NaCl Auto Ranging Meter

1413 microsiemens EC Value

Multiparameter Photometer with digital pH

CalCheck Cuvette Kit

Total Hardness Photometer: Range LR: 0 to 250 mg/l

CalCheck standard for Hardness

Water Proof Portable DO, 230 V

Zero Oxygen Solution - 500 ml

DO probe electrolyte solution 500 ml

Precision Turbidity and Free/ Total Chlorine Meter

Muffle Furnace ( 200 x 200 x 300 mm)

Vaccum Pump

Hot Air Oven(355 x 355 x 355 mm)

Magnetic Stirrer

Centrifuge - Laboratory

Vortex Mixer

Round Hot Plate

TKN Digester with Condenser

Heating Mantle

Microprocessor programme Temp controller

Glasswares

Bottle Reagent - 2 Liter

Volumetric Flask - 250 ml

Volumetric Flask - 500 ml

Volumetric Flask - 1000 ml

Filter Paper - 42

Desicattors 3082

Desicattor Plain with Knobbed

Desicattor with Plastic 3082

Measuring Cylinder - 500 ml

Measuring Cylinder - 250 ml

Burette 2122 - 50 x 0.1 Class B

Pipette 7060 Mohr type 25 x 0.2 ml - Class B

Pipette 7060 Mohr type 10 x 0.1 ml - Class B

Pipette 7060 Mohr type 5 x 0.1 ml - Class B

Pipette 7060 Mohr type 2 x 0.1 ml - Class B

Bottle Reagent - 250 ml

Bottle Reagent - 500 ml

Bottle Reagent - 1 liter

Bottle Reagent - 2 liter

Bottle Reagent - 500 ml

Gloves

Tongs

Bottle Reagent - 500 ml

Silver Sulphate - 25 g

Sulphuric Acid - 500 ml

Hydrochloric Acid - 500 ml

Sodium Hydroxide Pellet - 500 g

Potassium Dichromate - 500 g

Oxalic Acid - 500 g

Earthling as per ISI Specification with an earth electrode of 2.1mt class 'B' GI pipe of dia not less than 40mm and with 20mm dia copper earth flat of size 125mm x50mmx6mm, with funneling arrangement using charcoal, common salt, G.I.reducer, check nuts etc., and masonry work and providing RCC cover slab 38mm thick for the Brick masonry including cost of steel and fabrication of reinforcement etc., complete in all respects as directed by the departmental officers. (SD 233)

Supplying and run off 8 SWG copper wire on walls or below ground level with necessary 'U' nails, earth work excavation and refilling & including the cost of all materials etc., complete in all respects as directed by the departmental officers.(SD 75)

Supplying and Fixing of 3 Phase DB with MCB 12 way TPMCB sheet steel distribution boards (flush type/surface type) fitted with bus bars and neutral links with three phase MCB outgoings and separate 4 way provision for accommodating One No. 4 pile incoming MCB / Isolator and another separate 4 way provision for accommodating One No. 4 pole ELCB / RCD (totally 8 ways in one segment) (3 x 4 ways in each segment) and separate provisions for MCB / Isolator (totally 12 Nos.) for sub incomers in 3 segments with label holder etc.complete in all respects as directed by the departmental officers

Supply and run off 2 of 2.50sqm PVC insulated single core unsheathed copper conductor cable of 1100 V grade with ISI mark confirming to IS:694/1990 with continuous earth connection by means of 1.50 sqm PVC insulated single core unsheathed copper conductor cable confirming to IS:694/1990 in suitable PVC rigid pipe 1.8mm thick concealed in wall for mains including the cost of PVC pipes and specials, cables, cement, brass screws, T.W plugs, saddles and labour etc., complete in all respects as directed by the departmental officers. (derived from SD 55)

Supply and run off 2 of 1.5 sqmm PVC insulated single core unsheathed copper conductor cable of 1100 V grade with ISI mark confirming to IS:694/1990 with continious earth connection by means of 1.50 sqm PVC insulated single core unsheathed copper conductor cable confirming to IS:694/1990 in suitable PVC rigid pipe 1.8mm thick concealed in wall for mains including the cost of PVC pipes and specials, cables, cement, brass screws, T.W plugs, saddles and labour etc., complete in all respects as directed by the departemental officers. (derived from SD 54)

Supply and fixing of TNEB meter Board suitable for 32 A Three phase service connection with 32A fuse unit(500V)32A neutral link and earth link (1" x 1/8" Copper flat) on T.W plank of size 600mm x450mm x 19mm with supportingT.W.reepers of 1" thick oneither sider with painting withsuitable bolt and nuts for fixingthe TW plank on wall withearth connection and interconnection with 7/20 PVCinsulated copper wire from EBmeter to fuse unit. SD 127)

Wiring with 2 x 1.5 sqmm (22 /0.3 ) PVC insulated single core unsheathed copper conductor cable of 1100V grade in suitable PVC rigid pipe concealed in wall and ceiling with PVC accessories inflush with wall with 3mm thick hylum sheet cover with TW switch box and 5A F.T. switch with continuous earth wire connection of 14 SWG TC wire for making good of the concealed portion with suitable colour for PVC concealed light point / Fan point (For Electronic regulator). SD 23

Wiring with 2 x 1.5 sqmm (22 /0.3 ) PVC insulated single core unsheathed copper conductor cable of 1100V grade in suitable PVC rigid pipe concealed in wall and ceiling with PVC accessories inflush with wall with 150 x 100 x 113 mm TW switch box with 3mm hylum sheet cover for 5A 3 pin non inter locking CS plug with continuous earth wire connection of 14 SWG TC wire and making good of the concealed portion with suitable colour for concealed PVC plug point. SD 38

18 W 4 feet LED fitting wioth LED Single side PWD SOR Pg no

Supply and fixing of 1200mm (48") sweep AC ceiling fan complete with stepped electronic regulator with 300mm down rod on the existing clamp (SD111)

Supplying and fixing 12" (30cm dia) light duty Exhaust fan including cost of all materials,labour, lead, lift, etc complete SD 114

HT Service connection:

DP Structure

Supply, delivery of 6 pole structure materials with suitable Size RSJ along with all structure materials are as under for 22 KV Substation.

Chain link fencing with gate including the TNEB 2 poles Spreading of materials as per CEIG requirements

Transformer yard earthing using copper flat and TWIN earthing as per IS(Above 250 KVA Transformer sub station)

Transformer sub station erection charges

Distribution transformer - 11 kV/433V, DyN11, 250 KVA

On Load Tap Changer (OLTC) for transformer with Remote Tab Changer Control Panel

Supply and delivery of 4 Runs X 3 1/2 core 150 sq.mm. 1100V AC, PVC Aluminium Armoured UG Cable with ISI MARKCable distance between Transformer secondary to PCC Panel

Cable lugs for 150 sq.mm

Cable laying

Construction of transformer plinth

Civil works in DP Yard: Supply, levelling of 38mm blue granite jelly ( Depth-6") over layer of sand & Fencing Support works

Safety items for Substation & WTP

LT Electrical gloves

Electrical gloves tested to 11 KV /22 KV with wooden box dusted with french chalk powder

Electrical quality 6mm thick rubber mat

Fire Bucket-3 Nos Hooked to MS stand

5 kg capacity ISI marked Dry chemical powder fire extinguisher

Laminated shock treatment chart

Wooden First Aid Box

Three wire discharge rod

Wooden ladder for HT Supply (5 Mtr)

LED Rechargeable Emergency lamp for industrial use

Statutory Charges for TANGEDCO

Development charges (Over head)

Earnest Money deposit

Security deposit

Meter caution deposit, 22kV - Meter plus Metering set with Panel

Registration charges

Designing and preparation of CEIG drawings, obtaining Approval and safety certificate including submission of Completion report and rectification report for substation and related works.

PMCC Panel

Fabrication & Supply of M V Cubical Panel board vermin proof box of CRCA sheet 16 SWG powder coated, door with 180 degree opening, poly urethane/rubber gaskets as per IE rules - 1m2, Mechanical interlock for PCC with DP structurePanel type: CompartmentalizedBusbar: AluminumQuantity of Incomer feeders with metering chamber:(i) EB Incomer: 1 No. of 1250 Amps, 4 Pole ACB, EDO typeQuantity of Outgoing feeders:(i) 63 Amps SFU with HRC Fuselink-2 Nos.(ii) 250 Amps SFU with HRC Fuse link - 6 Nos. ( 1No. for existing 6.5 MLD WTP)(iii) 400 Amps SFU with HRC Fuse link - 2 Nos. ( 1No. for existing 6.5 MLD WTP)

Panel incomers with metering chamber

1250 Amps, 4 Pole, EDO type Air Circuit Breaker with Microprocessor based Trip unit (O/C, E/F, S/C)

2 lock with 1key Mechanical Interlocking System for M V Panel Board

Digital Multifunction meter- Three Phase Class 1-AC

Digital Voltmeter- Three Phase Class 1-AC

96 mm X 96 mm Three Phase Digital Ammeter Class 1-5A

LED indication lamp for R,Y,B phase identification, ACB-ON/OFF, Circuit healthy, TRIP indication lamp

Trip and Close Switch

Closing Coil

Current Transformer for Metering & Protection

Cable duct, DIN tail, Auxiliary block for power contactor, Power & Control terminal block, end plate and end clamp and necessary accessories

Aluminium flat for Horizontal Main bus & Vertical bus @ 0.7 Amps / sq.mm & Earth flat

Bus bar support, Base frame, supporting angle / channel, Panel internal wiring for entire panel

Outgoing Feeders of PMCC Panel

63 Amps TPN, SFU with HRC fuse Link for LDB & PDB panel - Each 1 No.

250 Amps TPN, SFU with HRC fuse Link (i) Existing Raw water pump room, MCC panel for new WTP, APFCR Panel, Spare - Each 1 No.)(ii) Proposed Clear water pump - 2 Nos.

400 Amps TPN, SFU with HRC fuse Link - Proposed Clear water pump - 2 Nos.

Soft starter with Bye pass contactor in Standalone panel

Supply and delivery of floor mounted type soft starter suitable for the LT motor offered for operation in AC three Phase 50Hz (+/- 5%), 415V(+/-10%) including MCCB with Microprocessor based Trip unit, Semiconductor fuse, Bye pass contactors suitable for 29 KW rating, Over load relay, instrument panel with frequency meter, Ammeter, Voltmeter, indicating lamp 6Nos, LED ON/OFF type and Start /Stop push button.

MCC Panel

Fabrication & Supply of M V Cubical Panel board vermin proof box of CRCA sheet 16 SWG powder coated, door with 180 degree opening, poly urethane/rubber gaskets as per IE rules - 1m2, Panel type: CompartmentalizedBusbar: 250 Amps Aluminum with designing of 0.7 Amps / Sq.mm Busbar, Quantity of Incomer feeders with metering chamber:Incomer: 1 No. of 250 Amps, 3 Pole MCCBQuantity of Outgoing feeders:(i) DOL feeder upto 5.5kW : 10 Nos.(ii) Star-Delta feeder: 25 kW : 2 Nos.,40 kW : 2 Nos, (iii) 32 Amps SFU with HRC Fuse link - 7 Nos.(iv) Empty feeder suitable for 63 Amps SFU - 2 Nos for future use.

Panel incomers with metering chamber

250 Amps, 3 Pole, MCCB with Microprocessor base Trip Unit ( Over current, Earth fault, Short Circuit), Extended rotary Handle, Phase Barrier, Spreader Terminal with all accessories

Digital Multifunction Meter, Three Phase Class 1-AC

LED indication lamp for R,Y,B phase identification, MCCB Trip indication

Current Transformer for Metering & Protection (250/5A)

MCB, 2Pole/3Pole

Cable duct, DIN tail, Auxiliary block for power contactor, Power & Control terminal block, end plate and end clamp and necessary accessories

Size of Aluminium flat shall be designed with Current carrying: 0.7 Amps/ q.mm and both Horizontal Main bus & Vertical bus with equal rating of panel incomer, & 50 X 6 mm Aluminium Earth flat.

Control busbar

Bus bar support, Base frame, supporting angle / channel, Panel internal wiring for entire panel

Feeder for Raw Water Pump; Rating: 25 KW; Type: Star-Delta Starter Quantity - Nos.2

100 Amps TPN Switch fuse Unit with 80 Amps Fuse link

45 Amps, 3Pole Power Contactor

Bimetallic Thermal overload relay ( 30-50 Amps)

Star -Delta Timer

LED indication lamp for ON, OFF, Trip, indication lamp

ON Pushbutton and Emergency STOP Push button, Mushroom type Actuator, Push to Close and Turn to Release

96 mm X 96 mm Three Phase Digital Ammeter Class 1-5A

Current Transformer for Metering

Auxiliary contactor for ON,OFF & Trip

6 Amps, 2Pole Control MCB

Auxiliary block for power contactor, Power & Control terminal block, end plate and end clamp and necessary accessories

Feeder for Backwash blower ; Rating: 24KW; Type: Star-Delta Starter Quantity - 2 Nos.

63 Amps TPN Switch fuse Unit with 32 Amps Fuse link

18 Amps, 3Pole, Power Contactor

Bimetallic Thermal overload relay ( 9-15Amps)

Star -Delta Timer

LED indication lamp for ON, OFF, Trip, indication lamp

ON Pushbutton and Emergency STOP Push button, Mushroom type Actuator, Push to Close and Turn to Release

96 mm X 96 mm Three Phase Digital Ammeter Class 1-5A

Current Transformer for Metering

6 Amps, 2Pole Control MCB

Auxiliary block for power contactor, Power & Control terminal block, end plate and end clamp and necessary accessories

Outgoing feeders

63/32 Amps TPN Switch fuse Unit with Fuse link for LCP of filter press, Clarifier, Chlorination & Control transformer

Panel utility

Thermostat with space heater, 6 Amps, 2 Pole MCB, Door switch with CFL lamp

Erection, testing commissioning charges

APFCR panel

Fabrication & Supply of M V Cubical Panel board vermin proof box of CRCA sheet 16 SWG powder coated, door with 180 degree opening, poly urethane/rubber gaskets as per IE rules - 1m2.Panel type: Non -CompartmentalizedBusbar: AluminumQuantity of Incomer feeders with metering chamber:(i) Incomer: 1 No. of 250 Amps, 3 Pole MCCBQuantity of Outgoing feeders:(i) 25 kVAR Capacitor : 3 Nos.(ii) 10 kVAR Capacitor : 1 No.(iii) 5 kVAR Capacitor : 2 Nos.(iv) 2 kVAR Capacitor : 2 Nos.(v) 1 kVAR Capacitor : 1 Nos.

250 Amps, 3 Pole, MCCB with Microprocessor base Trip Unit ( Over current, Earth fault, Short Circuit), Extended rotary Handle, Phase Barrier, Spreader Terminal with all accessories

APFCR relay with 8 Stage output

Digital VAF- Three Phase Class 1-AC

LED indication lamp for R,Y,B phase identification, Capacitor-ON indication

Current Transformer (250/5A)

Cable duct, DIN tail, Terminal block, end plate and end clamp and necessary accessories

Base frame, supporting angle / channel, Panel internal wiring, earthing for entire panel

Power capacitor for power factor improvement with oil filled with discharge resistance Heavy Duty, 3 phase 525 Volts 50 HZ conforming to ISS:2834 with ISI marking

MCCB, Heavy duty Capacitor duty contactor, Illuminated ON/OFF push button for each rating

MCCB, Heavy duty Capacitor duty contactor, Illuminated ON/OFF push button for each rating

Erection, testing commissioning charges

Power & Control Cable

Supply and delivery of 1Run X 3.5 core 185 sq.mm. 1100V AC, PVC Aluminium Armoured UG Cable with ISI MARKCable distance between PMCC to existing Raw water Pump room

Supply and delivery of 1Run X 31/2 core 240 sq.mm. 1100V AC, PVC Aluminium Armoured UG Cable with ISI MARKCable distance between PMCC to existing Clear water Pump room

Supply and delivery of 1Run X 31/2 core 185 sq.mm. 1100V AC, PVC Aluminium Armoured UG Cable with ISI MARKCable distance between PMCC to MCC panel of New WTP.

Supply and delivery of 31/2 core 185 sq.mm. 1100V AC, PVC Aluminium Armoured UG Cable with ISI MARKCable distance between PMCC to 105 kVAR Panel.

Supply and delivery of 4 core 6 sq.mm. 1100V AC, PVC Aluminium Armoured UG Cable with ISI MARKCable distance between PMCC to LDB Panel

Supply and delivery of 4 core 6 sq.mm. 1100V AC, PVC Aluminium Armoured UG Cable with ISI MARKCable distance between PMCC to PDB Panel

Supply and delivery of 2Runs X 3 core X 16 sq.mm. 1100V AC, PVC Aluminium Armoured UG Cable with ISI MARKCable distance between MCC to Raw water pump of New WTP.

Supply and delivery of 1Run x 3 core X 2.5 sq.mm, Copper conductor, armoured, XLPE insulated ,UG Cable with ISI MARK for the Sub Light distribution Boards

Supply and delivery of 1Run x 3 core X 2.5 sq.mm, Copper conductor, armoured, XLPE insulated ,UG Cable with ISI MARK for the following equipments.

Cable distance from MCC panel to Flash mixer - 2 Nos.

Cable distance from MCC panel to Flocculator - 2 Nos.

Cable distance from MCC panel to FeCl3 Agitator - 2 Nos.

Cable distance from MCC panel to Poly agitator - 2 Nos.

Cable distance from MCC panel to Alum dosing pump - 2 Nos.

Cable distance from MCC panel to poly dosing pump - 2 Nos.

Cable distance from MCC panel toVaccum pump - 2 Nos.

Cable distance from MCC panel to Filter press

Cable distance from MCC panel to Clarifier mechanism

Supply and delivery of 5 core, 1.5 sq.mm, 1100V AC, XLPE Copper Armoured UG Cable with ISI MARK Cable distance between MCC panel to Individual equipments

Supply and delivery of 19 core, 1.5 sq.mm, 1100V AC, XLPE Copper Armoured UG Cable with ISI MARK Cable distance between Transformer marshalling to RTCC panel

Supply & termination of cable lugs and excavation, refilling, laying of cable

Lighting fixtures

7 Metre Length Single Bracket Pole with Base Plate (250 x 250 x 6mm)114.30mm OD x 5.40mm Thick x 4000mm Length, 88.90mm OD x 4.85mm Thick x 1500mm Length, 76.1mm OD x 3.25mm Thick x 1500mm Length

Main Light distribution board: Industrial type 12 Ways Three Phase DB with IP54 Protection with MCB and ELCB

Light distribution board: Industrial type 12 Ways Single Phase DB with IP54 Protection.

10 Amps 30mA TP ELCB

Double Pole 6A to 32A, 10KA

Switch board with 6A switch

6/16A Socket - 3 Module

30W LED Street Light Fitting for Walkway platform & storage TankMake: Philips / Havells

120W LED Street Light Fitting with LED

20W 4 Feet LED fixtures

AC Ceiling Fan 1200 mm

AC Exhaust Fan 300 mm (12”) sweep (Light duty)

MS/Fibre Louvers shutters arrangements for 300mm AC Exhaust Fan

Supply, wiring for indoor & outdoor light fittings with conduits.1.5 sq.mm for indoor wiring and 2.5 sq.mm for street fitting

Street light junction box

Erection and commissioning charges

Local Push button Stations with Supports

Supply & erection of Local ON/OFF push button station near the Pumps.(a ) Enclosure shall be Thermoplastic and suitable for 5 Core X 1.5 Sq.mm, Bottom entry, 3/4" 2 Way cable entry, double compression gland.(b) 1 No. of Non illuminated "ON" Green Colour Push button with 2 NO + 2 NC contact.and 1 No. of Emergency Stay put Red Colour Mushroom actuator, Press to Lock & Turn to release "OFF" push button with 2 NO + 2 NC contact without key type.(C) Supply of accessories including Name plate, SS fasteners, Neoprene endless moulded gasket, 2 Nos. of Earthing, Screw type terminal blocks with Spare.(d) Fabrication & supply of ISMC 100 Channel supports for fixing the Push button station at 1.2 m Height from ground level, one coat of primer & painting along with all necessary accessories & hardwares

Earthing arrangements

Twin CI Earthing as per IS 3043/1987 and Latest amendments upto 150 HP

Supply, laying, termination of earth flat for the following items:(i) 2 Runs X 65 mm X 10 mm GI earth flat for Panel (ii) 2 Runs X 25 mm X 3 mm GI earth flat for 11 Kw and 30 kW.(iii) 2 Runs X 50 mm X 6 mm GI earth flat above 37 kW

2 Runs X 8 SWG green colour sleeved copper wire for street light & Local push button station

Cable tray

GI Hot dip/ Powder coated 16 SWG Cable tray with 50/100/150/200/300mm width and 50mm height

Chequered Plate, MS Channel & supports

Fabrication & erection charges

Electrical safety certificate

Designing and preparation of CEIG drawings, obtaining Approval and safety certificate including submission of Completion report and rectification report for WTP equipments.

Submerible Pump Set

Supply and delivery of Open well Submersible pump set conforming to IS 14220/2002 and as amended thereafter and BEE 3 Star Rated capable of dischargingthe following duties due to all causes. The pump shall be with stainless steelshaft and dynamically balanced bronze mixed type impeller, CI FG 200 gradecasing and brass screws and rotor shall be of copper rod as per IS 613/1984with ISI mark. The pump suitable for installation in sump with 1.1KV grade 3core suitable copper flat submersible cable to a length of 15m with necessarycable joints. The non-return valve located at the top of the pump in thedischarge outlet connection is to be designed with minimum friction. The pumpshould be directly coupled to 2880 RPM, three phase, 50 Hz (±5), 415V+6% &415V-15% squirrel cage induction motor suitable for DOL upto 5 HP, FullyAutomatic Air break Star Delta up to 20 HP and Auto Transformer starter forabove 20 HP starting and for continuous operation.

Vertical turbine pump

Supply and delivery of Vertical water/Oil lubricated statically, dynamically, hydraulically balanced Turbine pump capable of discharging the following duty condition as given below due to all causes with surface discharge head confirming to IS 1710 and as amended as on date with accessories as per IS 5120/1977 ( Reaffirmed 2011 ) and as amended thereafter to suit the site condition. The speed, No. of stages, sizes of column pipes and line shaft indicated is based on site condition prevailing during investigation. The pump should be supplied with non reversible ratchet pin housing safety clutch, suction strainer etc. The Pump Bowl assembly shall be with bronze impeller running at 1450 rpm. The pump includes suitable head shaft, suitable 1.5 metre long SS line shaft required Nos. to suit the well depth, Rubber line shaft bearing of required Nos., C.I Bearing retainer of required Nos., 100 litre HDPE Pre- lubricating tank with 20mm PVC Rigid pipe connection along with GM gate valves, Suitable ERW column pipe of each 1.5m long of required Nos. to suit the well depth, Suction bell mouth of suitable size, M.S. clamps suitable for column pipe/line shaft -2 set and Spanner - 1 set etc complete (Rates given are with suspension length of 7m, bronze impeller, SS 401 shaft, MS column pipe, discharge case & CI bell mouth.)

Horizontal Split Casting Centrifugal pump

Supply and delivery of Horizontal split casing centrifugal pump conforming to IS 1520 and as amended thereafter with CI casing andsplit glands, stainless steel shaft, hydraulically and dynamically balanced bronze impellers capable of discharging required quantity of water against a total head noted below due to all causes and with the accessories such as G.M air release cock, Grease cup, G.I priming funnel, M.S lifting hook, drip water G.I pipe connections, leading to the outside of pump house rubber water deflector, doubleflap foot valve, G.M strainer including unique tyre type coupling, common M.S fabricated base to mount pump and motor and other standard fittings etc complete. Pump shall be capable of discharging the specified quantity at the head noted at the minimum NPSH at site conditions. The shut off head shall be atleast 25% over and above the head at duty point. The pump shall be suitable foroperation in AC three phase, 415 V, 50 Hz, 1500 RPM.

Soft Starter

Supply and delivery of suitable KW indoor automatic air cooled dust and vermin proof FLEX COMPENSATED MAGNETIC AMPLIFIER Soft Starter for the operation in 3.3 KV three Phase 50 HZ, AC supply termination with phase segregated neutral terminal box of the motor , housed in 14 SWG sheet steel enclosure, painted with epoxy or polyurethene , 230V AC 10 Amps control supply , Class B insulation, 300 mm height fabricated pedastal (to prevent water ingress for starter panel) and condensation heater with switch with thermostat, interlocking with running motor with built in facility for run mode/by pass etc. complete. The starter may be provided with contactors suitable for next standard higher KW rating, Over load relay, instrument panel with frequency meter, Ammeter, Voltmeter, indicating lamp 6 Nos, LED ON/OFF type and Start /Stop push button. SUITABLE FOR H.T. SQUIRREL CAGE MOTOR

FCMA SOFT STARTER-38 HP

labour Charges

Submerible Pump Set

Labour charges for the erection of submersible pumpsetin borewell/openwell including fixing and jointingsubmersible cable with proper clamps upto the starter torequired depth and also fixing of riser pipes to therequired depth valves erection clamps, pressure gaugesupto the exterior wall of pump room and erection ofpanel board consisting of TPICN switches starter,Voltmeter, Ammeter, three pilot (indicating) lampscapacitor single phasing preventor, water level guard andlaying and jointing the cables and twin earthing as per IErules etc., complete and testing the pumpset and trailrun for 10 days.

Horizontal Split Casting Centrifugal pump & Vertical Turbine Pump

Labour Charges for erection of Horizontal shaft, centrifugal pumpset (Coupled/Monoblock) in bore well/Open well including fixing of suction pipe and foot valve upto a maximum depth of 7 metres and delivery pipes to the required length with valves, pressure gauges upto the exterior wall of pump room and erection of panel board consisting of TPIC switches starter, Voltmeter, Ammeter, Capacitor single phasing preventor and laying and jointing the cables and twin earthing as per IE rules including providing bed blocks etc., complete and operating the pumps and trial run for 10 days including signing of completion of reports as required by EB authorities.

Providing TWIN Earthing to all starters

upto 25 HP

Above 25 upto 60 HP

Cable: supply and fixing of 4 sq mm PVC INSULATED AND SHEATHED 3 CORE FLAT TYPE COPPER CABLE CONFORMING TO IS 694/1990 AND AS AMENDED THEREAFTER .

Supply and delivery of brand new approved make 1.1 KV grade armoured aluminium conductor cable confirming to ISS 1554 part I with ISI marking including loading, freight, transit insurance, incidental charges, packing, taxes and unloading, stacking at site in good condition including excise duty etc., complete as directed by the TWAD Board officers.

3.5 C x 50 Sqmm (Aluminium) (From pole to MV panl)

3 C x 35 Sqmm (Aluminium) (From MDB panel to Pumpset through starter

3 C x 10 Sqmm (Aluminium) (To capacitor)

4 Cx 4 Sqmm (Aluminium) (To lighting)

3C x 2.5 sq.mm Copper cable for control system

Laying of 1.1 KV class UG cable in trench / GI pipe / on pole as required.and as directed by Engineer incharge.

3.5 C x 50 Sqmm (Aluminium) (From pole to MV panl)

3 C x 35 Sqmm (Aluminium) (From MDB panel to Pumpset through starter

3 C x 10 Sqmm (Aluminium) (To capacitor)

4 Cx 4 Sqmm (Aluminium) (To lighting)

3C x 2.5 sq.mm Copper cable for control system

JOINTING OF L.T.CABLES 3,3.5,4CORE 1.1KV GRADE ARMOURED ALUMINIUM CONDUCTOR CABLE CONFIRMING TO IS1554 AND AS AMENDED THERE AFTER PARTI WITH ISI MARKING

3.5 C x 50 Sqmm (Aluminium) (From pole to MV panl)

3 C x 35 Sqmm (Aluminium) (From MDB panel to Pumpset through starter

3 C x 10 Sqmm (Aluminium) (To capacitor)

4 Cx 4 Sqmm (Aluminium) (To lighting)

3C x 2.5 sq.mm Copper cable for control system

Supply and delivery of 150mm dia Bourden tube type pressure gauge (glycerin filled)with concentric scale suitable for pumpsets in item I duly mounted on a teak wood Board to be fixed on well of the pump house with required copper tube connection with brase stop cock etc. The gauge should conform to relevant I.S. 3624

Supply and delivery of following safety appliances including loading, freight, transit insurance, incidental charges, packing, taxes and unloading, stacking at site in good condition including excise duty etc., complete as directed by the TWAD Board

Electrical gloves tested to 11 KV / 22 KV with wooden box dusted with french chalk powder

Supply and fixing of Electrical quality 6mm thick rubber mat

Supply and fixing of 5 Kg capacity ISI marked Dry chemical powder fire extinguisher

Supply and fixing of fire bucket - 3 Nos. hooked to MS stand

Supply and fixing of laminated shock treatment chart

Supply and fixing of wooden first aid box

Supply and fixing of Rechargeable Emergency lamp (600mm Fluoracent lamp)

Supply and Delivery of Tools required for Pumproom

Provision for DI Pipe connection

Electro Magnetic Flow Meter-300 mm

300 mm DI PN10 Flanged pipes (2m length pipes) - Intake Well

HSC Connection - 20 mm - Providing House service connection with MDPE 20mm pipe (supply, lowering, jointing & testing), electrofusion tapping saddle PE 80 blue, PN 12.5 with female threaded metal insert of SS 304, Brass Ferrule as per IS 319 grade of sizes 15mm, 20mm and 25mm size and threaded to suit the corresponding bore sizes of 15mm dia size ( 1/2", ), Poly Propylene compression Male Threaded Adaptor with metal insert of SS 304 , Poly propylene 90 Degree Compression elbow with compression joint at both ends, Poly Propylene compression Female Threaded Adaptor with metal insert of SS 304 and protection box of size 20cm x 30cm for fixing of Water Meter all as per standard including road cutting, replacement of utilities providing house service connection, refilling, retoration of roads/drains testing etc complete with materials and specification as instructed by department officers.