PROVISION OF SCREEN WALL BEHIND STATION PARADE GROUND AT ICGS AND PROVISION OF ROAD FURNITURE AT ICGAS RATNAGIRI

Amount

Surface dressing not exceeding 15 cm in depth in hard/dense soil complete all as specified and directed.

Excavating in trenches n exc 1.50 m wide and n exc 1.50 m depth for foundation etc n exc 10 sq m on plan and not exc 1.50 m in depth in soft/disintegrated rock and getting out all as specified and directed.

Excavating in post holes (or similar holes) each not exc 0.5 Cum, getting out, returning, filling in & raming earth/ broken rubble mixed with earth around, in layers n. exc. 25cm, watering and removing surplus soil to a distance n exc 50m and making good surface in soft/disintegrated rock all as specified and directed.

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exc 25 cm in soft/disintegrated rocks all as specified and directed.

Removing excavated disintegrated rock n exc. 50m and depositing where directed at a level n exc. 1.50 m above the starting point as specified and as directed.

Removing excavated disintegrated rock to a total distance of 250m and depositing where directed at a level n exc. 1.50 m above the starting point as specified and as directed.

M & L for PCC,(1:4:8) type D2 (using 40mm graded stone aggregate) as in foundation filling and mass concrete all as specified and directed.

M&L for PCC (1:3:6) type C2 (using 40mm graded stone aggregate) as in foundation, filling and mass concrete all as specified and directed.

M&L for reinforced cement concrete, (1:2 :4), type B1 (Nominal mix) using 20 mm graded stone aggregate as in beams , cantilever , bressummers, Arches, lintels over 1.5 m span all as specified and directed.

Use and waste of formwork to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including supports, overhangs, etc. also splays between floors & beams, etc. for rough finished curved surfaces of concrete all as specified and directed.

M&L for TMT bar 10mm dia and over cut to length bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips all as specified and directed.

M&L for TMT bar 5mm dia and over up to and including 10mm dia, as in stirrups , spacers and binders cut to length bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips all as specified and directed.

M & L for PCC, type (1:3:6) C1 (using 20mm graded stone aggregate) as in coping, bed blocks etc including necessary formwork all as speficified and directed.

M & L for PCC,type (1:4:8) D2 (using 40mm graded stone aggregate) (75 mm thick) as in sub base all as specified and directed.

M & L for PCC,type B1 1:2:4 (using 20mm graded stone aggregate) as in floor (40 mm thick) and finish the surface even and smooth without using extra cement all as specified and directed.

M&L for Machine cut Laterite stone masonry exceeding 10cm in width, square rubble, regular coursed, well bonded, bedded and solidly hearted built in cement mortar 1:6 all as specified & as directed.

M&L for Machine cut Laterite stone masonry exceeding 10cm in width, square rubble, regular coursed, well bonded, bedded and solidly hearted built in cement mortar 1:6 but curved on plan of mean radius n exc 6 M

M & L for rendering 15mm thick in cement mortar 1:6 on fair faces of laterite stone masonary all as specified and as directed.

S & F rolled mild steel Joist, channel, angle, or tee sections, framework, fixed independently, without connecting plates, etc. (cut to ordinary lengths i.e. within 20mm of the length indicated) of Fe 410-0 W (Gde E-250) quality A all as specified and directed.

M&L for stainless steel round pipes of grade 304 , any dia up to 150 mm dia for road furniture including cutting to size, erecting in position and welding /brazing all as specified and directed

Supply and fix Aluminium composite panel (ACP) AL-33D sheet 3 mm panel with 0.3mm aluminium coil thickness the aluminium alloy being AA3105, for exterior applications sign board fixed on MS frame work by riveting or bolts & nuts @ 300 mm center to center all along the periphery

M & L for 15 - 20 mm thick Granite (of any colour) stone slab machine cut in skirting/dado over cement plaster and jointed with grey cement slurry pointed with white cement with admixture of pigment to match the shade of granite stone including cutting and polishing over 10mm thick plaster in CM 1:4 on fair faces of brick work or on one side of lathing as in backing coat for granite

S&F 3M Retro reflective film and oracle colour film by pressure sensitive adhesive backing designed and cut,in the shape of numerical, Alphabets etc. on Aluminium composite panel for sign board.Size of letters as approved.

S&F print with 3M Retro reflective film and UV eco print by pressure sensitive adhesive backing on Aluminium composite panel for sign board printing image as approved.

M&L for preparing new plastered / unplastered surfaces of wall of any description and applying two coats of weatherproof acrylic emulsion antifungai (Exterior grade) paint over a coat of primer complete all as specified and directed.

M & L for preparation of new steel surfaces of any description, over 10 cm width or girth, not otherwise described and applying two coats of synthetic enamel paint over a coat of zinc chrome primer all as specified and directed.

M & L for Raised pointing to squared rubble, coursed or uncoursed masonry in CM (1:4) all as specified and directed

M/s Ajinkya Kailas Laigude

shrilaxminarayan constructions

SUPRADA CONSTRUCTION

Unique Associates