SPL REPAIR TO BLDG NO P-295 (DOUBLE STORAGE OR LINES) OF DEF AND COY AT SGNR MIL STN

Amount

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing) and rubbish off the premises complete all as specified and directed by Engineer - in - Charge.

M&L glazed ceramic coloured tiles grade, (300x600)x7mm thick as on vertical surfaces like dados or skirting over 10mm thick rendering in CM 1:4, set & jointed in neat cement slurry and pointed in white cement mixed with pigment to match the shade of tiles complete all as specified and directed by Engineer - in - Charge.

Demolition of cement Concrete(un-renforced) in ground floors and pavings n exc 15 cm thickness (below or above ground level) complete all as specified and directed.

M&L for non skid coloured ceramic tiles 7 to 8 mm thick area of each tile exceeding 0.11 sqm but not exc 0.18 sqm laid in floor set and jointed in cement slurry including 15 mm thick screed bed or bedding layer of cement mortar 1:4 for laying floor finish even & fair and pointed in white cement mixed with pigment to match the shade of tiles complete all as specified and directed.

M&L for 25 thick plain cement concrete flooring type B-0 1:2:4 (12.5 mm graded stone aggregate) complete all as specified and directed.

M&L machine cut Kota stone flooring 18-20 mm thick over 20 mm thick screed base in cement mortar 1:4, laid and jointed with grey cement slurry mixed with pigments to match the shade of the slabs including rubbing,grinding and rounding of edges (moulding of edges) and mirror polishing complete all as specified and directed by Engineer - in - Charge.

All as per above item No-6 but in vertical surfaces like dados or skirting over 10mm thick rendering in CM 1:4, set & jointed in neat cement slurry and pointed in white cement mixed with pigment to match the shade of tiles complete all as specified and directed by Engineer - in - Charge. (Note: Single piece in stair cases.)

Demolition of cement concrete of any description and in any position for sunken portion and floor all as specified and directed by Engr-in-charge.

M&L for water proofing treatment to RCC sunken slab as specified below and as directed by engr-in-charge:- (a) 15mm plaster in CM 1:3 with WPC on raised vertical surface. (B) Cleaning the surface with wire brush/coir brush, removing loose material like dust particles ,dirt etc. (c) Creating fillet covering of 50x50 mm with polymer modified mortar on the junction of slab and walls (d) Apply first coat of two component modified polymer coating on the horizontal and vertical surfaces. (e) Provision of glass fibre mesh of 2x2 mm immidiately on above coating (f) Apply second coat of two component modified polymer coating after 72 hours (g) Laying concrete 1:4:8 over the coating as per requirement (h) Joining the sanitary pipe with non shrink cementatiuos grout (k) Complete the treatment to be carried out by authorised applicator of waterproofing manufacturer. NOTE : (i) The Treatment shall be carried out as per the manufacturers industreis and as directed by engr-in-charge. (ii) only polymerchemical coating upto height 1.20m for toilet and 2.1m height for bathroom, rates of chemical deemed in this quoted rates. (iii) WPC shall be measured and paid saperately.

Supply only Water proofing compound

Demolition of Brick tiles or terracing tiles , single layer on roofs complete all as specified and directed.

Demolition of old mud phuska,any type of soil in any depth removing rubbish of the premises cleaning surface and preparing to receive new cement plaster concreting complete all as specified and directed by Engineer-in-Charge.

M&L for PCC 1:2:4 type B2(20 mm graded aggregate) as in roof padding/roof kerbs or mud stops, rounded or chamfered on edges complete all as specified and directed by Engineer in chgarge.

M & L for applying pitch free PU based Liquid applied single component elastomeric seamless, water and vapour proof membrane system for concrete . Provide and apply moisture insensitive primer @ 0.20-0.25 kg/m2. Allow the primer to cure for 6-8 hrs to tacky condition. Provide and apply 2 coats of a single component PU based cold applied seamless waterproofing membrane over the above PUF layer coverage @ 2.3-2.5 kg/m2 in 2-3 coats to achieve DFT of 1.5mm. Conforming tensile strength (2N/sqmm) (ASTM D412)/Tear resistance (15KN/m) (ASTM D624-00) and crack bridging (ASTM C 836/ASTM C 1305 modified) 2mm. After 72 hours of curing, flood test can be carried out to a minimum depth of 50mm of water for 24 hours. Drains shall be plugged and barriers placed to contain the water complete all as specified and directed by Engr-in- charge. Note :- (i) All above operations to be done by auth application in order all as specified and directed. (ii) Auth company will submit confirmation of their Auth applicator before execution of Work. Make :- Fosroc /Sika/Bostik/Choksey

Supply and fixing Heat Resistant Terrace Tiles (300 mm x 300 mm) X 8-10mmthick with SRI (solar refractive index) > 78, solar reflection > 0.70 and initial emittance > 0.75 on waterproof and sloped surface of terrace, laid on 20 mm thick cement sand mortar in the ratio of 1:4 (1 cement : 4 coarse sand) . Filling of the joints of tiling with epoxy including providing skirting upto 150 mm height along the parapet walls in the same manner complete all as specified and directed.(Note: Rates of epoxy deemed to be included in this quoted rates.)

Dismantling water tank capacity exc 250 Ltr and n exc 1000 ltr complete all as specified and directed by Engineer - in - Charge.

S&F rotational moulded polyethylene water storage tank white colour 1000 ltrs capacity three layered (Cylindrical vertical with closed top) hoisted and fixed in position including 25mm bore PTMT ball valve, high pressure with epoxy coated Aluminium rod & high density plastic ball screwed for iron pipe or brass ferrule (minimum weight 455gms) complete all as specified and directed by Engineer - in - Charge.

Taking down chowkhats or frames (without taking off shutters from the frames) not exceeding 1.5sqm each complete all as specified and directed by Engineer - in - Charge.

S&F Factory made single extruded WPC (Wood Polymer Composite) solid door/ window/ Ceosetory windows & other Frames/ Chowkhat of size 45 x 75 mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/ cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2, modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardant and fixed in position with MS hold fast/ lugs/SS dash fasteners of required dia and length complete as per direction of Engineer-in-Charge.

S & F Providing and fixing factory made single extruded WPC (Wood Polymer Composite) solid decorative type flush door shutter of size 30 mm thick comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant. WPC to be laminated with PVC foil of minimum 14 microns thick of approved design pasted with hot melt adhesive on both faces of shutter and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, all as per direction of Engineer- In- Charge including supply and fixing following items : (a) Stainless Steel (304 Grade) Finished Butt Hinges 100mm - 4 nos. per leaf (b) Stainless Steel (304 Grade) Finished Square Tower Bolt 200mm long - 2 nos per leaf (c) Stainless Steel (304 Grade) Finished Handles 200 mm - 2 nos. per leaf (d) Stainless Steel (304 Grade) Finished Sliding Bolt 300 mm - 1 no. per leaf (e) Stainless Steel (304 Grade) Finished Floor Door Stooper - 1 nos. per leaf

S&F stainless steel wire cloth, 0.36 mm nominal dia of wire and average width of aperture 1.40mm complete all as specified and directed by Engineer - in - Charge.

S&F Aluminum Grill powder coated of approved design/pattern with aperture size 50X50 mm and wire dia 5 mm fixed with Aluminum Frame complete all as specified and directed by Engr-in-charge.

S&F in repairs stainless steel wire cloth, 0.36mm nominal dia of wire and average width of aperture 1.40 mm complete all as specified and directed by Engineer - in - Charge.

M&L for mild steel work as in frame work/guard bar for door and window and as similar work including cutting tops to shape, drilling holes, notching for wire etc conforming to Fe-290 grade E-165 complete all as specified and directed .

S&F steel windows with side hung shutters including projecting types hinges with steel handles and steel peg stay complete with glazing bars complete with dove tailed or welded including one coat of red oxide primer all as specified and directed by Eng-in-charge.

S&F steel windows with side hung shutters including projecting types hinges with steel handles and steel peg stay complete without glazing bars complete with dove tailed or welded including one coat of red oxide primer all as specified and directed by Eng-in-charge.

S&F stainless steel wire cloth, 0.36 mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples all as specified including taking down ms frame and fixing ms frame with new wire mesh with tinned tack/by welding in steel window/ventilator and making good the disturbed portion during execution complete all as specified and directed by Engineer - in - Charge.

Taking down wooden shutters only of any description area exceeding 1.0 sqm and not exceeding 2.0 sqm each and refixing in same opening after necessary easing, adjustments, minor repairs, oiling, adjustment with cutting or fixing plain fillets/planks made from second class hard wood etc to remove gap between floor and shutter complete all as specified and as directed by Engineer-in- charge.

Taking down chowkhats or frames (without taking off shutters from the frames) exceeding 1.5sqm but n.exc 4.0sqm each complete all as specified and directed by Engineer - in - Charge.

S & F pressed steel door frames with one or more rebates including necessary fixing lugs, hinges, lock strike plate etc., size of frame 125x60mm complete all as specified and directed by Engineer - in - Charge.

S & F pressed steel door frames with one or more rebates including necessary fixing lugs, hinges, lock strike plate etc., size of frame 105x60mm complete all as specified and directed by Engineer - in - Charge.

M&L plain Cement concrete 1:2:4 type B–0(12.5 mm graded stone aggregate) filling of pressed steel frame and hold fast blocks etc complete all as specified and directed by Engineer - in - Charge.

M & L for applying two coats of synthetic enamel paint (ordinary tint) over two coat of red oxide primer on new steel surface over 10 cm width or girth, not otherwise described including preparation of surface complete all as specified and directed by Engineer - in - Charge.

S & F for 35mm thick factory made gauged skelton shutters open rebated and prepared to receive gauze etc edges of framing plain, chamfered or rounded fitted with cut and mitred beady for receiving gauze etc of 35mm thick and door for Iind class hard wood rail and style as specified in SSR Part-I Section 8, cluase 8.24(a) and all as specified and directed by Engr-in-Charge.

S&F 40 mm thick factory made flush shutter Plain, framed, solid core consturction with block board core and plywood face panels, commerical type on both sides covered with mica on both sides complete all as specified and directed by Engineer-in-charge.

M&L for preparation of surfaces of new wooden Surfaces of any description over 10 cm width or girth and applying two coat of synthetic enamel paint over one coat of pink primer complete all as specified and directed.

S&F 100 mm Butt hinges stainless steel with galvanised mild steel hinge pin and fixed type C-21 all as specified and directecd by Engr-in-charge.

S& F aluminium anodised barrel tower bolts of extruded section and fixed 150 mm size complete all as specified & directed by Engineer in charge.

S&F 300 mm mild steel sliding door bolts, clip type, stone enameled block with bright bolt not less than 12mm dia with and incl a minimum of 6 bolts and nuts, 4 on bolt plate 2 on staple plate.

S & F aluminium handles D type with back plate, anodised, 150mm long complete all as specified and directed by Engineer - in - Charge.

S&F 300 mm ordinary rat tail rod pattern springs including roller and roller plate complete all as specified and directed by Engr-in-charge.

S&F floor door stopper of aluminium alloy body and tongue, anodised with hard drawn steel spring fixed in floor and overall length of cover plate 140 mm complete all as specified and directed by Engineer in charge.

S&F in repair 15 mm dia chromium plated concealed type stop valves, cast copper aloy with crutch or butterfly handles screwed down high pressure, screwed both ends for iron and fixed.

S&F in repairs, Angle valves, chromium plated cast screwed down, high pressure copper alloy, with crutch or butterfly handles, screwed both ends for but fancy type 15mm bore iron pipe or complete all as specified and directed by Engineer - in - Charge.(make:Cera /parryware/jaquar or equivalent )

S&F in repairs chromium plated shower rose of any colour with or without swivel joints 150mmx150mm square in size including shower arm complete all as specified & directed by Engineer in charge.(make:Cera /parryware/jaquar or equivalent )

S&F 5mm thick Glass Shelf(600mm long) Glass fixed with and including chromium plated brass screws and wooden/plastic cleats complete all as specified and directed by Engineer - in - Charge.

S&F in repairs SS soap dish of any size fixed with screws complete all as specified and directed by Engineer in charge.

S&F in repairs grating doom 100 mm dia of stailess steel with and without hole complete all as specified and directed by Engineer vin charge.

S & F in repair stainless steel tubular towel rail 20mm dia “D” type 60 cm long between flanges including brackets complete all as specified and directed by Engineer - in - Charge.

S & F in repair stainless steel towel ring min 30mm dia including brackets complete all as specified and directed by Engineer - in - Charge.

S&F in repairs fancy type long body bib taps,15 mm cast copper alloy, with crutch or butterfly handles, screwed down, screwed for iron pipe or brass ferrule for 15mm bore complete all as specified and directed by Engineer - in - Charge(.make:Cera /parryware/jaquar or equivalent )

S&F in repair PVC connections 15 mm size with PTMT nuts of length 450 mm complete all as specified and directed by Engineer - in - Charge.

S&F in repair water closet vitreous china squatting pan "Orrisa pattern" size 580mmx440mm white with integral foot rests (Excl flushing cistern) including all joints and making good to the floor complete all as specified including CI 'P' trap/S trap all as specified and directed by Engr-in-charge.

S&F in repairs, PVC low level flushing cistern 10 lirs capacity, valve-less, syphonic action type, white, with inlet, ball valve, float, and handle including brackets, PVC connections 15 mm size with PTMT nuts of length 450 mm ,including 32mm bore flush pipe of polyethylene of low or high density of PVC complete all as specified and directed by Engineer - in - Charge.

S&F, in repair vitreous china oval type wash hand basin white, 32mm bore brass chromimum plated waste coupling & 32mm bore low density ployethylene (LDPE) flush pipe of pressure rating 6Kgf/Sq cm (1.00 M long) complete, including 15mm bore 450 mm length PVC connection with PTMT nuts complete all as specified and directed.(make:Cera /parryware/jaquar or equivalent )

S&F in repairs low density polyethylene pipes (LDPE) 32 mm dia and 1000 mm long of pressure rating 6 kgf/cm2 fixed complete to walls, ceilings or in floors complete all as specified and directed by Engineer in charge.

Supply only fancy type swan neck pillar taps, cast copper alloy, with capstan heads, chromium plated, screwed down high pressure of 15 mm bore diawith or without lettered Hot or cold with long screwed shanks and fly nuts, screwed for iron pipe and fixed complete all as specified and directed by Engineer in charge.(MAKE:CERA cat No- F1020101,parryware/jaquar or equivalent )

S&F hat pegs and hooks (cloth hanger with six peg set each) complete all as specified.

Dismantling cast iron pipe of any dia, jointed in cement mortar and taking out of trenches if required complete all as specified and directed by Engineer - in - Charge.

S&F 100mm bore cast iron sand cast soil, waste and vent pipes, in any length with or without ears, with cement joints, fixed to walls complete all as specified and directed by Engineer - in - Charge.

S&F 75mm bore cast iron sand cast soil, waste and vent pipes, in any length with or without ears, with cement joints, fixed to walls complete all as specified and directed by Engineer - in - Charge.

S&F 100mm bore cast iron bends sand cast (any radius), diminishing pieces or tapers (larger bore measured) fitted with oval access door complete all as specified and directed by Engineer - in - Charge.

S&F 100mm bore cast iron 'Y' tee sand cast fitted with oval access door complete all as specified and directed by Engineer - in - Charge.

M&L for CI floor trap 100 mm with anti cockroaches grating including jointing to waste pipe fixed in cement concrete type B-1 (1:2:4) all as specified and directed by Engr-in-charge.

M&L for CI floor trap 75mm with anti cockroaches grating including jointing to waste pipe fixed in cement concrete type B-1 (1:2:4) all as specified and directed by Engr-in-charge.

Taking down eaves gutters and rain water pipes (any size or pattern) including all fittings, heads, shoes, bends, swan – necks, etc. including cleaning of any description complete all as specified and directed by Engineer - in - Charge.

M&L bands straps supports or stays for rainwater ventilating pipes including bolts confirming to Fe 290 Gde E-165 all as specified and directed by Engr-in-charge.

S&F 110mm bore PVC (SWR) rain water pipe single socketed in any length with rubber ring joints, jointed with solvent joint fixed to wall complete all as specified and directed by Engineer - in - Charge.

S&F 110mm bore PVC (SWR) bends any radius complete all as specified and directed by Engineer - in - Charge.

Taking up or down for 20mm bore steel water tubing galvanised with connection including cleaning for refixing complete all as specified and directed by Engineer - in - Charge.

Taking up or down for 15 mm bore steel water tubing galvanised with connection including cleaning for refixing complete all as specified and directed by Engineer - in - Charge.

Taking up or down for 25mm bore steel water tubing galvanised with connection including cleaning for refixing complete all as specified and directed by Engineer - in - Charge.

S&F steel water tubing galvanised 15mm bore, “medium grade” with all fittings and fixed to walls and ceiling or in floor complete all as specified and directed by Engineer - in - Charge.

S&F steel water tubing galvanised 20mm bore, “medium grade” with all fittings fixed to wall and ceiling or in floor complete all as specified and directed by Engineer - in - Charge.

S&F steel water tubing galvanised 25mm bore, “medium grade” with all fittings fixed to wall and ceiling or in floor complete all as specified and directed by Engineer - in - Charge.

S&F Vitreous china premium/1st quality wash down water closet wall hung EWC white (closed pattern incl all necessary like rag bolts/gel gasket, PVC (SWR) WC connector benty type etc.) Plastic water closet soft slim seat cover, white, closed pattern with flat bottom, and cover with aluminised hinging device, icluding taking down & remove to store old EWC complete all as specified and as directed.

S&F in repairs vitreous china urinals, half stall type flat back complete including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including 60 mm long brass screws, pointing around urinal back in cement, fixing automatic flushing cistern with brackets, flush pipe grating and union for discharge pipe including waste pipe and trap complete all as specified and directed by Eng in charge.

S&F Urinal spreader of PTMT any colour for fixing 15 mm dia pipe complete all as specified and directed by Engineer in charge.

M&L for granite (of any type)18- 20 mm thick machine cut, bedded & jointed with grey cement slurry and pointed with white cement with admixture of pigment to match the shade of granite stone including grinding, rounding of edges (moulding of edges) and polishing complete laid over 15 mm thick screed bed in CM 1:4 etc all as specified and directed by Engineer in charge.

S&F Harrison rails mild steel chromium plated with fixing brackets, stops, rollers etc 20mm bore dia complete all as specified and directed by engr-in-charge.

M&L for 75mm thick Cement concrete type C-2 , 1:3:6 (40 mm graded aggregate) as in plinth protection laid in bay n.exc 2.5m length all as specified and directed.

Demolition of RCC as in Roofs, floors ( other than ground floors), beams, staircases, landing, chajjas and similar suspended work complete all as specified and directed by EIC.

Demolition of brick work built in cement mortar of any description complete all as specified and directed by Engineer - in - Charge.

M&L brick work with sub class 'B' Bricks, straight or curved on plan exceeding 6 mtr mean radius built in CM 1:6 complete all as specified and directed by Engineer - in - Charge.

M & L for Brickwork with subclass ‘B’ bricks, straight or curved on plan to any radius in half brick thick walls built in cement mortar 1:6 complete all as specified and directed by Engineer - in - Charge.

M&L Form work to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work not exceeding 200 mm thick (horizontal or sloping)

M&L for RCC nominal mix 1:1 1/2: 3 (using 20mm graded stone aggregate ) as in slabs suppotred on walls, beams and columns complete all as specified and directed.

S & F for TMT bars 10 mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.90 mm dia complete all as specified.

S&F plain mild steel sheeting 0.80mm thick in expansion/bldgs joints gutter valley, hips with screw and fastners including all fixing cleats etc complete all as specified and directed by engr-in-charge.

Taking down cement plaster of amy description on bricks or concrete surfaces of walls including racking out joints, hacking for keys scrubbing down with water etc. complete all as specified directed by Engr-in-Charge.

M&L 15mm thick, rendering in cement mortar 1:6 to brick/concrete wall surfaces finished even and smooth without using extra cement complete all as specified and directed by Engr-in-Charge.

M&L 15mm thick, rendering in cement mortar CM 1:4 to brick/concrete wall surfaces in two layers first layer 10mm thick and second layer 5mm thick with WPC 3% by wt of cement finished even & smooth without using extra cement complete all as specified and directed by Engr-in-Charge.

M&L 5mm thick, rendering in cement mortar 1:3 to ceiling surfaces on patches finished even and smooth without using extra cement in patches complete all as specified and directed by Engr-in-Charge.

M&L for prepration of New plastered Internal wall surface complete applying the following :- (a) Applying two coat wall care putty (1.5mm thick each coat ) on wall surface and smoothening the surfcae with sand papers / Mechanised sanding etc prepatory to paint as directedcoomplete all as specified (b) Applying one coat of internal Wall Primer by using Roller over complete all as specified (c) Applying two coat of interior acrylic Emulsion Paint Roller over complete all as specified Note : (i)Contractor may use manual scraping tools for complete removal and surface prepration with prior approval of Engr-in-chrge in case of places where using of Mechanical equiment are not posiible (ii) The prepared surface after wall putty GE will inspect and approve the further internal finishes work after approval of the prepared surface through written order.

M&L for applying two coat of Acrylic emulsion with putty (1.5mm thk )on newly plastered surface of ceiling etc complete all as specified.

M&L for prepration of New plastered External wall surface complete applying the following :- (a) Applying two coat wall care putty (1.5mm thick each coat) on wall surface and smoothening the surfcae with sand papers / Mechanised sanding etc prepatory to paint as directedcoomplete all as specified (b) Applying one coat of Exterior Wall Primer by using Roller over complete all as specified (c) Applying two coat of Acrylic smooth Exterior Emulsion using Roller over complete all as specified Note : Contractor may use manual scraping tools for complete removal and surface prepration with prior approval of Engr-in-chrge in case of places where using of Mechanical equiment are not posiible. (ii) The prepared surface after wall putty GE will inspect and approve the further external finishes work after approval of the prepared surface through written order.

Material and labour for complete removal of existing treatment on Old Internal wall surfaces of any desciption, preperation of surface by Mechanised sander having suction vaccum Bag using Smart periodical methodology and after preparing the surfaces applying the following complete all as specified and as directed by Engineer-in-charge:- (a) Applying Wall care putty in two coats 1.5 mm thick each for filling to depression of scraped surface/nail holes/light cracks etc and smoothening the surfcae with sand papers / Mechanised sanding etc prepatory to paint as directed. (b) Two coats of acrylic emulsion of approved tint over a coat of primer acrylic emulsion paint on old prepared surface by using paint brush / Roller. Note : Contractor may use manual scraping tools for complete removal and surface prepration with prior approval of Engr-in-chrge in case of places where using of Mechanical equiment are not posiible.

M&L two coat of acrylic emulsion on old decorated surfaces of ceiling including putty(1.5MM THK) preparation of surfaces by brooming down or steel wire brushing, scrapping down smoke soot, moulds, moss and efflorescent salts and trading oil and greasy spots complete all as specified and directed by Engr-in-Charge.

M&L for complete removal of existing treatment including filling depression of scraped surface with wall putty two coats 1.5 mm thick each on Old external wall surfaces of any desciption , prepratio of surface by Mechanised sander having suction vaccum Bag using Smart periodical methodology , complete all as specified and applying the following :- (a) M&L two coats of exterior acrylic emulsion by using Airless spray / Roller over and incl a coat of acrylic emulsion external primer complete all as specified Note : Contractor may use manual scraping tools for complete removal and surface prepration with prior approval of Engr-in-chrge in case of where using of Mechanical equiment are not posiible

S & F Health faucet (ABS Body) mild steel chromium plated suitable for 15 mm dia pipe with 1.25 metre long flexible tube and ABS wall hook including making connections and fixed in position complete all as specified and directed by Engineer - in - Charge.

S & F for 20mm dia Gun metal , gate or globe valves, with iron wheel head, screwed both ends for iron pipe and fixed complete all as specified and directed.

S & F for 25mm dia Gun metal , gate or globe valves, with iron wheel head, screwed both ends for iron pipe and fixed complete all as specified and directed.

S&F push type Metropole flush valve, made of brass with CP finishing suitable for 40mm CPVC pipe complete all as specified and directed by Engineer - in - Charge.(make - Jaquar, Prayag-BEA-35, ESS ESS or equivalent and approved by AO.

S&F CPVC pipes ISI marked IS 157778 with all brass fitting for hot and cold water fixed with solvent cement complete to walls and ceiling or laid in floors of 40mm bore of pipe size (SDR 11)

Material and labour for repair of chajja facia using cement mortar (1:3) n.exc 300 mm girth finishing the surface even and smooth complete all as specified and as directed by Engineer-in-Charge.

Drilling Holes of 12mm dia up to 100 mm deep holes in structural members at the interval of 300 mm in staggered manner or along the crack line in Reinforced Concrete (RC) structural element including cleaning of the holes by air blower and inserting 12mm dia NRV (Non Returnable Valve) nozzle compatible with epoxy injector and having machined external end to receive outlet of Grouting Gun. Fix inside the hole by applying thixotropic epoxy adhesive to ensure complete sealing and allow curing the system for minimum of 8 Hrs before Grouting including nozzle projections, excess putty, if any, over concrete element by grinding, leveling and finishing the external surface, after completion of the work, etc. complete all as specified and as directed by Engineer-in-charge.

Grouting, injecting two part, low viscosity, moisture insensitive injection liquid, based on high strength epoxy resin by pressure and using pressure epoxy injector with accessories till nozzle refused to accept the grout including mixing of grout having following properties:- (i) Mixed Density 1.1 kg/l (at +27°C); Viscosity ~ 250 mPas at +30°C and should comply according to ASTM C 881, Type II and IV, Grade-1, Class E+F (ii) Compressive strength >= 70 N/sqmm (7 days) according to ASTM C 579; Tensile Strength ~ 50 N/sqmm (after 7 days at +30°C cure) (According to ASTM D 638); Tensile Modulus ~ 2000 N/sqmm (after 7 days at +30°C cure) (According to ASTM D 638); (iii) Bond Strength ~ 10.8 N/sqmm (failure in concrete) after 14 days at +30°C cure; Flexural strength ~ 50 N/sqmm according to ISO 178. (iv) Seal the nozzle with thixotropic epoxy adhesive after the refusal of grout material from the nozzle. Note:- leakage through other nozzle or cracks are required to be monitored while grouting and such points to be sealed as and when required without any extra cost complete all as specified and as directed by Engineer-in-charge. Note :- Mode of measurement: per kg of material consumed Make: Sika - SikaDur 52 LP/ Fosroc- Conbextra EP 10/ Pidilite Dr Fixit Epoxy Injection Grout or equivalent make approved by GE in writing from E-in-Cs Br approved list.

M&L for providing and applying jacketing around coloumns/beams/Rcc or any other RCC members with micro concrete having a minimum compressive strength of 60N/mm2@ 28 days when tested as per ASTM C-109 and a flexural strength of 6 N/mm2 when tested as per ASTM C580 . The tensile strength shall be a minimum of 2.5 N/mm2 when tested as perASTMC 307. It shall provide an unrestrained positive expansion of upto 0.405 when tested as per ASTM C307. including all lifts, shuttering, drilling holes and fixing shear anchor as per specification complete. Note: Reinforcement shall be measured and paid seperately.(Rates including jacketing, formwork and microconcrete) complete all as specified and directed.(Make: Sika-SikaDur 32LP/ FOSROC-Nitobond SBR (EP)/Pidilite Dr Fixit Super Latex (EP) ,make approved by GE in writing from E-in-C' Br approved list.

Supply for Pipe supporting clamping - single pipe of dia 110mm(4'') down take pipe fixing done with clamping system consists of profile bracket+continuous slotted C channel +U bolt rubber sleeve mounted system running vertically with wall distance 75mm (3'') pipe support clamping made of : 1. Profile bracket having wall distance 75mm(3'') made of low carbon Hot roll guage corrected oil pickled and drawn(HROPD) Steel (IS 1079): material size 32mm X3mm with ribbs and notch are hot dip galvanized+ Zn Al flake coated having salt spray test(test method-ASTM B-117-2019) results 2000hrs with SS304 Hex flange bolt with serration 5/16x3/4 (A/F 13mm) as per DIN 6921 and SS304 Hex flange nut BSW 5/16X18X8X13 with serration as per DIN 6923 .2. Continuous slotted "C' Channel with ribs to be used of size 250mm (10'') made of low carbon hot roll guage corrected oil pickled and drawn(HROPD) steel (is 1079) are hot dip galvanized+Zn Al flake coated with material thickness of 3mm. 3. U bolt rubber sleeve mounted are made of low carbon mild steel with rod diameter 7mm approx: Zn Al flake coated with noise absorbing semitransparent ribbed silicon rubber sleeve; with Hex flange nut BSW5/16X18X8X13 with serration set as per DIN 6923-Zn Al flake coated.Hotdip galvanizing: as per IS 2629(1985)-610grams/m2(>85 microns). Material grade: IS 1079 used as per MTC confirms to EN 10204 3.1. Material qty: for one unit: 1. Profile bracket wall distance 75mm(3'')-02 Nos. 2. Continuous slotted C channel of size 250mm(10"). 3. U bolt rubber sleeve mounted for 110mm(4")CI or PVC pipe dia-01 No: and 4. Fixing nail Zn coated of thickness 6.5mm and length 63mm(2.5'')-04Nos. Fixing detail: Pipe support clamping unit to be fixed at every metre distance in the duct as specified in Chief Engineer Bathinda ZoneTechnical drawing(TD) of factory made pipe supporting system:DRG NO-BTD-916.

Supply for Pipe supporting clamping - single pipe of dia 75mm(3'') down take pipe fixing done with clamping system consists of profile bracket+continuous slotted C channel +U bolt rubber sleeve mounted system running vertically with wall distance 75mm (3'') pipe support clamping made of : 1. Profile bracket having wall distance 75mm(3'') made of low carbon Hot roll guage corrected oil pickled and drawn(HROPD) Steel (IS 1079): material size 32mm X3mm with ribbs and notch are hot dip galvanized+ Zn Al flake coated having salt spray test(test method-ASTM B-117-2019) results 2000hrs with SS304 Hex flange bolt with serration 5/16x3/4 (A/F 13mm) as per DIN 6921 and SS304 Hex flange nut BSW 5/16X18X8X13 with serration as per DIN 6923 .2. Continuous slotted "C' Channel with ribs to be used of size 250mm (10'') made of low carbon hot roll guage corrected oil pickled and drawn(HROPD) Steel (is 1079) are hot dip galvanized+Zn Al flake coated with material thickness of 3mm. 3. U bolt rubber sleeve mounted are made of low carbon mild steel with rod diameter 7mm approx: Zn Al flake coated with noise absorbing semitransparent ribbed silicon rubber sleeve; with Hex flange nut BSW5/16X18X8X13 with serration set as per DIN 6923-Zn Al flake coated.Hotdip galvanizing: as per IS 2629(1985)-610grams/m2(>85 microns). Material grade: IS 1079 used as per MTC confirms to EN 10204 3.1. Material qty: for one unit: 1. Profile bracket wall distance 75mm(3'')-02 Nos. 2. Continuous slotted C channel of size 250mm(10"). 3. U bolt rubber sleeve mounted for 110mm(4")CI or PVC pipe dia-01 No: and 4. Fixing nail Zn coated of thickness 6.5mm and length 63mm(2.5'')-04Nos. Fixing detail: Pipe support clamping unit to be fixed at every metre distance in the duct as specified in Chief Engineer Bathinda ZoneTechnical drawing(TD) of factory made pipe supporting system:DRG NO-BTD-916.

Taking down carefully aluminium point wiring (light, fan, socket or power, bell complete fitting such as sockets, ceiling roses, pendants, batten holders, regulators and making good the disturbed surfaces of wall, floors, ceiling in CM 1:3 etc complete all as specified and directed by Engineer - in - Charge.

M & L for concealed conduit point wiring complete for light/ fan on independent /combine board with cable 2.5 sqmm (Nominal area) FRLSH PVC insulated multistranded unsheathed copper conductor, drawn in and including PVC Concealed conduit pipe medium grade 20 mm dia, pipe hooks , elbows, juction covers and junction boxes , after cutting in wall chasing for conduits and sinking's for metal flush boxes suitable length and thickness for mounting, switches, sockets,fan regulator with cover plate with frame and making the good disturbed surfaces of wall in CM 1:3 with white wash or existing colour including provision of continuous earth continuity conductor along with point wiring of 1.5 sqmm copper PVC insulated cable for one light/ fan point controlled by one switch and connected to common earth dolly, complete all as specified and direced by the Engineer in charge.

All as per Ser item No 115.00 above but for one switch socket combination 5/6 amp on independent board complete all as specified and directed by Engineer - in - Charge.

All as per Ser item No 115.00 above but for one three pin socket outlet 5 Amp on same board with other switches complete all as specified and directed by Engineer - in - Charge.

All as per Ser item No 115.00 above but for one switch socket combinationt 6 pin 5/ 15 Amps on independent board with copper conductor 2.5 Sqmm complete all as specified and directed by Engineer - in - Charge.

All as per Ser item No 115.00 above but for one light point controlled by two 2 ways switches complete all as specified and directed by Engineer - in - Charge.

S & F in replacement modular switch 5/6 Amps single pole one way one module complete all as specified and directed by Engineer - in - Charge.

S & F in replacement modular socket 16 A - 2/3 pin combined 2 Module complete all as specified and directed by Engineer - in - Charge.

S & F in replacement Modular switch 1 way 16 A complete all as specified and directed by Engineer - in - Charge.

S & F in replacement modular switch 5/6 Amps single pole 2 way complete all as specified and directed by Engineer - in - Charge.

S & F in replacement modular Socket 5 pin 5/6 Amps in 1 flush type 2 modular complete all as specified and directed by Engineer - in - Charge.

S & F in replacement stepped type, fan regulator not less than 120 watt for ceiling fan 1200/1400mm sweep complete all as specified and directed by Engineer - in - Charge.

S & F in replacement ceiling rose surface bakelite three terminals complete all as specified and directed by Engineer - in - Charge.

S & F in replacement of existing light fitting with LED batten 20W LED batten with 'Eye Soft' technology & glarefree diffuser for perfect application in modern homes or aliminium housing and integrated electronic driver, 20 watt having input voltage AC 140-300V, 50 Hz , 6500K, and all other accessories including connection with flexible cable copper conductor twin core of size 23/.2 mm upto ceiling rose/connector complete all as specified and directed by Engineer - in - Charge.

S&F security light fitting LED TYPE 25 watt with all necessary acessories, Clear transparent acrylic cover, prewire suitable to operate on 230 volt 50 HZ AC & Supply and fixing to wall / on pole including fixing arrangement with suitable galvanized iron pipe 35 mm bore “light grade” brackets 2 mtr length bent to shape to obtained required shape including clamps, nuts / bots / washers etc connecting with suitable flexible copper wire of size 23/0.0076 complete all as specified and directed by Engineer - in - Charge.

S & F in replacement compact and decorative energy efficient LED mirror light fittings with antiglare diffuser and decorative end caps suitable for 1x20 watt fittings 2 ft version including LED lamp 20 watt complete all as specified and directed by Engineer - in - Charge.

S & F in replacement angle holder insulated body with back plate for conduit fittings complete all as specified and directed by Engineer - in - Charge.

S&F LED lamp 9W for angle holder complete all as specified and directed by Engineer - in - Charge.

S & F in replacement of sub-main wiring with two single core cables PVC insulated and un-sheathed 2 x 6 sqmm (Nominal Area) FRLSH stranded copper conductor drawn in and including steel dia 25mm “medium quality” conduit including 1x6.00 Sqmm (Nominal Area) copper cable as earth continuity conductor after chasing in wall and making good the disturbed surfaces and white wash or existing colour, necessary junction box and covers including necessary connections, PVC flexible pipes are used in pannel board while connecting the cable complete all as specified and directed by Engineer - in - Charge. Note :Two length of 6 sqmm cable and one length of 6 sqmm earth cable alongwith PVC conduit will be measured as one running length.

S & F in replacement of sub-main wiring with two single core cables PVC insulated and un-sheathed 2 x 4 sqmm (Nominal Area) FRLSH stranded copper conductor drawn in and including steel dia 20mm “medium quality” conduit including 1 x 4.00 Sqmm (Nominal Area) copper cable as earth continuity conductor after chasing in wall and making good the disturbed surfaces and white wash or existing colour, necessary junction box and covers including necessary connections, PVC flexible pipes are used in pannel board while connecting the cable complete all as specified and directed by Engineer - in - Charge. Note : Two length of 4 sqmm cable and One length of 4 sqmm earth cable alongwith PVC conduit will be measured as one running length.

S&F in repairs Sheet metal enclosure for double door Vertical DBs made out of CRCA mild steel sheet surface with insulated material like polyester with epoxy powder coated surface mouting VTPN 4 Way 415 Volt ISI marked 250Amps busbar stove enameled dust and vermin proof,IP:43 protection suitable for incorporation FP MCCB(V-Tech) N3 Frame upto 125A, Isolators and including give connection with wire and cable etc complete all as specified and directedby engineer -in-charge.

S&F in repairs Sheet metal enclosure for double door DBs made out of CRCA mild steel sheet surface with insulated material like polyester with epoxy powder coated surface mouting SP & N 8 Way 415 Volt ISI marked 200 Amps busbar stove enameled dust and vermin proof suitable for incorporation MCBs and Isolators etc complete all as specified and directedby engineer -in-charge.

S&F in repairs MCCB TPN 100 Amps with breaking capcity 16kA ,Fixed TM and 415 volts AC Supply ISI marked complete all as specified and directed by Engineer - in - Charge.

S & F in replacement MCB ‘C’ series type suitable for 240 volts, 10 KA, AC supply 5 to 32 Amps , single pole (SP) with over load and short circuit protection and rupturing capacity not less than 10KA complete all as specified and directed by Engineer - in - Charge.

S & F in replacement MCB ‘C’ series type suitable for 240 volts, 10 KA AC supply 32 Amps, S P & N with over load and short circuit protection and rupturing capacity not less than 10KA complete all as specified and directed by Engineer - in - Charge.

M & L for Earthing complete with GI earth plate electrode 60 cm x 60 cm x 6 mm thick burried directly in ground (earth pit not less than 2.25 Mtr deep below ground level ) with top edge of plate not less than 1.5 Mtr below ground level , connecting to GI earth lead 4 mm dia GI earth wire ,by means of bolts,nuts and washers of GI and protection by provision of GI medium grade pipe 15 mm bore including provision of concrete pit in PCC (1:2:4) type B1 using 20 mm grade stone aggregate with 40 mm thick cover of RCC (1:2:4) reinforced with XPM (weight not less than 4 gs /Sqmm ) and frame of angle iron 25mmX25mmX6mm with lugs 02 Nos and with 6 mm dia MS bar handle made to shape ,GI light grade 20mm bore pipe for watering perforated at the bottom 1.75 meter long placed ontop edge of earth plate common salt and charcoal filling test point made out of 40 mmX 8 mm FI with fixing arrangement ,funnel, wire mesh and earth work inhard dense soil, returning filling in and removal of surplus soil to a distance not exceeding 50 mtrs all as per electric plate no.3 of SSR part 1 and connecting to earth test point all as specified and directed by Engr -In - Charge

Taking down and depositing of old unsv ceiling fans of any size in MES yard complete all as specified and directed.

M&L for painting of ceiling fans complete, in situ with synthetic enamel paint by spraying including filling cavities with filler, one coat after cleaning all dust etc complete all as specified and directed.

Hanging only ceiling fan (M.D. supply) and connecting up including provision of cable from ceiling rose or connector to fan all as specified and directed by Engr-in-Charge.

Taking down and depositing of old unsv exhaust fans of any size in MES yard complete all as specified and directed.

M&L for painting of exhaust fans complete, in situ with synthetic enamel paint by spraying including filling cavities with filler, one coat after cleaning all dust etc complete all as specified and directed.

S&F heavy duty metal body exhaust fan of 300 mm sweep, 240 volt, copper winding, complete with louvers and shutter and mounted in suitable opening arrangement in wall and connecting up including 3 core PVC insulated PVC sheathed copper conductor flexible cable 24/0.2mm from ceiling rose to fan complete including breaking of brick wall and making a hole for fixing of exhaust fan including grouting of bolts and making good to distubed wall in cement mortar (1 :4) white washing matching with existing colour etc.

Taking down and depositing of old unsv geysers of any size in MES yard and refixing the same in existing position complete all as specified and directed.

S &F storage type water heater (geyser) electrical operated 230/240 volts 25 ltr capacity, BEE 5 star rated complete with all safety equipment and accessories such as safety valve, thermostat, fusible plus etc required for proper functionality & including electric/earth connections and carrying out grouting & complete installations with mounting bolts , nuts including testing after installation complete all as specified and directed by Engr-in-Charge.

PAREEK AND COMPANY (BID ID -3334649)

Akarsha Enterprises (BID ID -3343407)