Development of Batadrava Than as Cultural and Tourist Destination at Batadrava, Nagaon, Assam (Phase-II)

Amount

Earth work in excavation by mechanical means (Hydraulic excavator)/ manual means over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan) including getting out and disposal of excavated earth lead upto 50 m and lift up to 1.5 m, as directed by Engineer-in charge. All kinds of Soil

Excavating trenches of required width for pipes, cables, etc including excavation for sockets, and dressing of sides, ramming of bottoms, depth up to 1.5 m, including getting out the excavated soil, and then returning the soil as required, in layers not exceeding 20 cm in depth, including consolidating each deposited layer by ramming, watering, etc. and disposing of surplus excavated soil as directed, within a lead of, etc. and disposing of surplus excavated soil as directed, within a lead of 50 m : Pipes, cables etc. exceeding 80 mm dia. but not exceeding 300 mm dia - All kinds of soil - Pipes, exceeding 80 mm dia, but not exceeding 300 mm dia for depth up to 1.50 m

Extra for excavating trenches for pipes, cables etc. in all kinds of soil for depth exceeding 1.5 m, but not exceeding 3 m. (Rate is over corresponding basic item for depth up to 1.5 metre).

Extra for excavating trenches for pipes, cables, etc., in all kinds of soil for depth exceeding 3 m in depth, but not exceeding 4.5 m. (Rate is over corresponding basic item for depth up to 1.5 metre.)

Filling available excavated earth (excluding rock) in trenches, plinth,sides of foundations etc. in layers not exceeding 20cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift up to 1.5 m.

Excavating, supplying and filling of local earth (including royalty) by mechanical transport up to a lead of 5km also including ramming and watering of the earth in layers not exceeding 20 cm in trenches, plinth, sides of foundation etc. complete.

Diluting and injecting chemical emulsion for POST-CONSTRUCTIONAL anti-termite treatment (excluding the cost of chemical emulsion) :'Along the external wall below concrete or masonry apron using chemical emulsion @ 2.25 litres per linear metre including drilling and plugging holes etc.: With Chlorpyriphos/ Lindane E.C. 20% with 1% concentration

Diluting and injecting chemical emulsion for POST-CONSTRUCTIONAL anti-termite treatment (excluding the cost of chemical emulsion) :'Treatment of soil under existing floors using chemical emulsion @ one litre per hole, 300 mm apart including drilling 12 mm diameter holes and plugging with cement mortar 1 :2 (1 cement : 2 Coarse sand) to match the existing floor: With Chlorpyriphos/Lindane E.C. 20% with 1% concentration

Providing and laying in position cement concrete of 1:2:4 (1 cement : 2 coarse sand (zone-III) derived from natural sources : 4 graded stone aggregate 20 mm nominal size derived from natural sources) excluding the cost of centering and shuttering - All work up to plinth level :

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : 1:3:6 (1 Cement : 3 coarse sand (zone-III) derived from natural sources : 6 graded stone aggregate 20 mm nominal size derived from natural sources)

Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement - All work up to plinth level : 1:1.5:3 (1 cement : 1.5 coarse sand (zone-III) derived from natural sources : 3 graded stone aggregate 20 mm nominal size derived from natural sources)

Centering and shuttering including strutting, propping etc. and removal of form for Foundations, footings, bases of columns, etc. for mass concrete

Centering and shuttering including strutting, propping etc. and removal of form for Walls (any thickness) including attached pilasters, buttresses, plinth and string courses etc.

Centering and shuttering including strutting, propping etc. and removal of form for Suspended floors, roofs, landings, balconies and access platform

Centering and shuttering including strutting, propping etc. and removal of form for Lintels, beams, plinth beams, girders, bressummers and cantilevers

Centering and shuttering including strutting, propping etc. and removal of form for Columns, Pillars, Piers, Abutments, Posts and Struts

Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete up to plinth level.Thermo-Mechanically Treated bars of grade Fe-500D or more.

Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete above plinth level.Thermo-Mechanically Treated bars of grade Fe-500D or more.

Providing and laying in position ready mixed or site batched design mix cement concrete for reinforced cement concrete work; using coarse aggregate and fine aggregate derived from natural sources, Portland Pozzolana / Ordinary Portland /Portland Slag cement, admixtures in recommended proportions as per IS: 9103 to accelerate / retard setting of concrete, to improve durability and workability without impairing strength; including pumping of concrete to site of laying, curing, carriage for all leads; but excluding the cost of centering, shuttering, finishing and reinforcement as per direction of the engineer-in-charge; Concrete of M25 grade with minimum cement content of 330 kg /cum - All work up to Plinth level

Providing and laying in position ready mixed or site batched design mix cement concrete for reinforced cement concrete work; using coarse aggregate and fine aggregate derived from natural sources, Portland Pozzolana / Ordinary Portland /Portland Slag cement, admixtures in recommended proportions as per IS: 9103 to accelerate / retard setting of concrete, to improve durability and workability without impairing strength; including pumping of concrete to site of laying, curing, carriage for all leads; but excluding the cost of centering, shuttering, finishing and reinforcement as per direction of the engineer-in-charge; Concrete of M30 grade with minimum cement content of 350 kg /cum - All work up to Plinth level

Providing and laying in position ready mixed or site batched design mix cement concrete for reinforced cement concrete work; using coarse aggregate and fine aggregate derived from natural sources, Portland Pozzolana / Ordinary Portland /Portland Slag cement, admixtures in recommended proportions as per IS: 9103 to accelerate / retard setting of concrete, to improve durability and workability without impairing strength; including pumping of concrete to site of laying, curing, carriage for all leads; but excluding the cost of centering, shuttering, finishing and reinforcement as per direction of the engineer-in-charge; Concrete of M25 grade with minimum cement content of 330 kg /cum - All works above plinth level up to floor V level

Providing and laying in position ready mixed or site batched design mix cement concrete for reinforced cement concrete work; using coarse aggregate and fine aggregate derived from natural sources, Portland Pozzolana / Ordinary Portland /Portland Slag cement, admixtures in recommended proportions as per IS: 9103 to accelerate / retard setting of concrete, to improve durability and workability without impairing strength; including pumping of concrete to site of laying, curing, carriage for all leads; but excluding the cost of centering, shuttering, finishing and reinforcement as per direction of the engineer-in-charge; Concrete of M30 grade with minimum cement content of 350 kg /cum - All works above plinth level up to floor V level

Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in foundation and plinth in: Cement mortar 1:6 (1 cement : 6 coarse sand)

Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level in all shapes and sizes in :Cement mortar 1:6 (1 cement : 6 coarse sand)

Half brick masonry with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level. Cement mortar 1:3 (1 cement :3 coarse sand)

Extra for providing and placing in position 2 Nos 6mm dia. M.S. bars at every third course of half brick masonry.

Random rubble masonry with hard stone in foundation and plinth including levelling up with cement concrete 1:6:12 (1 cement : 6 coarse sand : 12 graded stone aggregate 20 mm nominal size) up to plinth level with : Cement mortar 1:6 (1 cement : 6 coarse sand)

Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS: 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade complete.

Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position with hold fast lugs or with dash fasteners of required dia & length (hold fast lugs or dash fastener shall be paid for separately).

Providing and fixing panelled or panelled and glazed shutters for doors, windows and clerestory windows, fixing with butt hinges of required size with necessary screws, excluding panelling which will be paid for separately, all complete as per direction of Engineer-in-charge. (Note:- Butt hinges and necessary screws shall be paid separately) Second class teak wood - 35 mm thick shutters

Providing and fixing ISI marked flush door shutters conforming to IS : 2202 (Part I) decorative type, core of block board construction with frame of 1st class hard wood and well matched teak 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters.35 mm thick including ISI marked Stainless Steel butt hinges with necessary screws

Providing and fixing ISI marked flush door shutters conforming to IS : 2202 (Part I) decorative type, core of block board construction with frame of 1st class hard wood and well matched teak 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters.30 mm thick including ISI marked Stainless Steel butt hinges with necessary screws

Providing and fixing M.S. grills of required pattern in frames of windows etc. with M.S. flats, square or round bars etc. including priming coat with approved steel primer all complete.

Providing and fixing bright finished brass butt hinges with necessary screws etc. complete : 125mx70mmx4mm

Providing and fixing bright finished brass tower bolts (barrel type) with necessary screws etc. complete : 250mmx10mm

Providing and fixing bright finished brass tower bolts (barrel type) with necessary screws etc. complete : 150mmx10mm

Providing and fixing bright finished brass door latch with necessary screws etc. complete : 300mmx16mmx5mm

Providing and fixing ISI marked aluminium butt hinges anodised (anodic coating not less than grade AC 10 as per IS: 1868) transparent or dyed to required colour or shade with necessary screws etc. complete:100mmx75mmx4mm

Providing and fixing ISI marked aluminium butt hinges anodised (anodic coating not less than grade AC 10 as per IS: 1868) transparent or dyed to required colour or shade with necessary screws etc. complete:75mmx45mmx3.2mm

Providing and fixing aluminium sliding door bolts, ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868), transparent or dyed to required colour or shade, with nuts and screws etc. complete : 300x16mm

Providing and fixing aluminium tower bolts, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868 ) transparent or dyed to required colour or shade, with necessary screws etc. complete : 200mmx10mm

Providing and fixing aluminium handles, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade, with necessary screws etc. complete : 100mm

Providing and fixing factory made P.V.C. door frame of size 50x47 mm with a wall thickness of 5 mm, made out of extruded 5mm rigid PVC foam sheet, mitered at corners and joined with 2 Nos of 150 mm long brackets of 15x15 mm M.S. square tube, the vertical door frame profiles to be reinforced with 19x19 mm M.S. square tube of 19 gauge, EPDM rubber gasket weather seal to be provided through out the frame. The door frame to be fixed to the wall using M.S. screws of 65/100 mm size, complete as per manufacturer’s specification and direction of Engineering- Charge.

Providing and fixing factory made panel PVC door shutter consisting of frame made out of M.S. tubes of 19 gauge thickness and size of 19 mm x 19 mm for styles and 15x15 mm for top & bottom rails. M.S. frame shall have a coat of steel primers of approved make and manufacture. M.S. frame covered with 5 mm thick heat moulded PVC 'C' channel of size 30 mm thickness, 70 mm width out of which 50 mm shall be flat and 20 mm shall be tapered in 45 degree angle on both side forming styles and 5 mm thick, 95 mm wide PVC sheet out of which 75mm shall be flat and 20 mm shall be tapered in 45 degree on the inner side to form top and bottom rail and 115 mm wide PVC sheet out of which 75 mm shall be flat and 20 mm shall be tapered on both sides to form lock rail. Top, bottom and lock rails shall be provided both side of the panel. 10 mm (5 mm x 2 ) thick, 20 mm wide cross PVC sheet be provided as gap insert for top rail & bottom rail, panelling of 5 mm thick both side PVC sheet to be fitted in the M.S. frame welded/ sealed to the styles & rails with 7 mm (5 mm+2 mm) thick x 15 mm wide PVC sheet beading

Providing and fixing factory made uPVC white colour casement/casement cum fixed glazed windows comprising of uPVC multi-chambered frame, sash and mullion (where ever required) extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), uPVC extruded glazing beads of appropriate dimension, EPDM gasket, stainless steel (SS 304 grade) friction hinges, zinc alloy (white powder coated) casement handles, G.I fasteners 100 x 8 mm size for fixing frame to finished wall, plastic packers, plastic caps and necessary stainless steel screws etc. Profile of frame & sash shall be mitered cut and fusion welded at all corners, mullion (if required) shall be also fusion welded including drilling of holes for fixing hardware's and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealant over backer rod of required size and of approved quality, all complete as per approved drawing & direction of Engineer-in-Charge. (Single / double glass panes and silicon sealant shall be paid separately). Variation in profile dimension in higher side shall be accepted but no extra payment on this account shall be made. Casement window double panels with top fixed with S.S. friction hinges (350 x 19 x 1.9 mm) made of (small series) frame 47 x 50 mm, sash 47 x 68 mm & mullion 47 x 68 mm all having wall thickness of 1.9 ± 0.2 mm and single glazing bead of appropriate dimension. ( Area of window up to 2.50 sqm).

Providing and fixing factory made uPVC white colour casement/casement cum fixed glazed windows comprising of uPVC multi-chambered frame, sash and mullion (where ever required) extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), uPVC extruded glazing beads of appropriate dimension, EPDM gasket, stainless steel (SS 304 grade) friction hinges, zinc alloy (white powder coated) casement handles, G.I fasteners 100 x 8 mm size for fixing frame to finished wall, plastic packers, plastic caps and necessary stainless steel screws etc. Profile of frame & sash shall be mitered cut and fusion welded at all corners, mullion (if required) shall be also fusion welded including drilling of holes for fixing hardware's and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealant over backer rod of required size and of approved quality, all complete as per approved drawing & direction of Engineer-in-Charge. (Single / double glass panes and silicon sealant shall be paid separately). Variation in profile dimension in higher side shall be accepted but no extra payment on this account shall be made. Casement window double panels with S.S. friction hinges (350 x 19 x 1.9 mm) made of (big series)frame 67 x 60 mm & sash / mullion 67 x 80 mm both having wall thickness of 2.3 ± 0.2 mm and single glazing bead/ double glazing bead of appropriate dimension. (Area of window above 1.50 sqm).

Providing and fixing factory made uPVC white colour fixed glazed windows/ ventilators comprising of uPVC multi-chambered frame and mullion (where ever required) extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), , uPVC extruded glazing beads of appropriate dimension, EPDM gasket, G.I fasteners 100 x 8 mm size for fixing frame to finished wall, plastic packers, plastic caps and necessary stainless steel screws etc. Profile of frame shall be mitered cut and fusion welded at all corners, mullion (if required) shall be also fusion welded including drilling of holes for fixing hardware's and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealant over backer rod of required size and of approved quality, all complete as per approved drawing & direction of Engineer-in-Charge. (Single / double glass panes and silicon sealant shall be paid separately). Variation in profile dimension in higher side shall be accepted but no extra payment on this account shall be made. Fixed window / ventilator made of (small series) frame 47 x 50 mm & mullion 47 x 68 mm both having wall thickness of 1.9 ± 0.2 mm and single glazing bead of appropriate dimension. (Area up to 0.75 sqm.)

Structural steel work riveted, bolted or welded in built up sections, trusses and framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete.

Providing and fixing 1 mm thick M.S. sheet door with frame of 40x40x6 mm angle iron and 3 mm M.S. gusset plates at the junctions and corners, all necessary fittings complete, including applying a priming coat of approved steel primer. Using M.S. angels 40x40x6 mm for diagonal braces

Supplying and fixing rolling shutters of approved make, made of required size M.S. laths, interlocked together through their entire length and jointed together at the end by end locks, mounted on specially designed pipe shaft with brackets, side guides and arrangements for inside and outside locking with push and pull operation complete, including the cost of providing and fixing necessary 27.5 cm long wire springs manufactured from high tensile steel wire of adequate strength conforming to IS: 4454 - part 1 and M.S. top cover of required thickness for rolling shutters. 80x1.25 mm M.S. laths with 1.25 mm thick top cover

Extra for providing mechanical device chain and crank operation for operating rolling shutters. Exceeding 10.00 sqm and up to 16.80 sqm in the area

Providing and fixing stainless steel ( Grade 304) railing made of Hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, i/c fixing the railing with necessary accessories & stainless steel dash fasteners , stainless steel bolts etc., of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-in?charge, (for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasteners etc.).

Dry brick on edge flooring in required pattern with bricks of class designation 7.5 on a bed of 12 mm mud mortar, including filling joints with Jamuna sand, with common burnt clay non modular bricks.

Cement concrete flooring 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate) finished with a floating coat of neat cement, including cement slurry, but excluding the cost of nosing of steps etc. complete. 40 mm thick with 20 mm nominal size stone aggregate

52 mm thick cement concrete flooring with concrete hardener topping, under layer 40 mm thick cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) and top layer 12 mm thick cement hardener consisting of mix 1:2 (1 cement hardener mix : 2 graded stone aggregate 6 mm nominal size) by volume, hardening compound mixed @ 2 litre per 50 kg of cement or as per manufacturer's specifications. This includes cost of cement slurry, but excluding the cost of nosing of steps etc. complete.

Providing and laying Ceramic glazed floor tiles of size 300x300 mm (thickness to be specified by the manufacturer), of 1st quality conforming to IS : 15622, of approved make, in all colours, shades, except White, Ivory, Grey, Fume Red Brown, laid on 20 mm thick bed of cement mortar 1:4 (1 Cement : 4 Coarse sand), jointing with grey cement slurry @ 3.3 kg/ sq.m including pointing the joints with white cement and matching pigments etc., complete.

Providing and laying vitrified floor tiles in 600mmx600mm (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS: 15622, of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joints with white cement and matching pigments etc., complete.

Providing and laying vitrified floor tiles in 800mmx800mm (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS: 15622, of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joints with white cement and matching pigments etc., complete.

Providing and laying Vitrified tiles in floor in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS:15622, of approved brand & manufacturer, in all colours and shade, laid on 20 mm thick cement mortar 1:4 (1 cement: 4 coarse sand) jointing with grey cement slurry @3.3 kg/sqm including grouting the joints with white cement and matching pigments etc. The tiles must be cut with the zero chipping diamond cutter only . Laying of tiles will be done with the notch trowel, plier, wedge, clips of required thickness, levelling system and rubber mallet for placing the tiles gently and easily. Glazed Vitrified tiles Matt/Antiskid finish of Size of Tile 600 x 600 mm

Providing and laying machine cut, mirror polished Marble stone flooring, in required design (Simple geometrical, abstract etc.) and in patterns in combination with Italian marble stones of different colours, shades and finished surface texture etc., in linear portions of the building, all complete as per the architectural drawings, with 18 mm thick stone slab laid over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with white cement slurry @ 4.4 kg/sqm, including pointing with white cement slurry admixed with pigment to match the marble shade, including rubbing, curing and polishing etc. all complete as specified and as directed by the Engineer-in-Charge. 18 mm thick Italian Marble stone slab, Perlato, Rosso verona, Fire Red or Dark Emperadore etc.

Providing and laying Polished Granite stone flooring in required design and patterns, in linear as well as curvilinear portions of the building all complete as per the architectural drawings with 18 mm thick stone slab over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with cement slurry and pointing with white cement slurry admixed with pigment of matching shade including rubbing, curing and polishing etc. all complete as specified and as directed by the Engineer-in-Charge. Polished Granite stone slab colour of Black, Cherry/Ruby Red or equivalent

Providing and laying pressed clay tiles (as per approved pattern 20 mm nominal thickness of approved size) on roofs jointed with cement mortar 1:4 (1 cement : 4 coarse sand) mixed with 2% integral water proofing compound, laid over a bed of 20 mm thick cement mortar 1:4 (1 cement : 4 coarse sand) and finished neat complete.

Providing and fixing precoated galvanized iron profile sheets (size, shape and pitch of corrugation as approved by Engineer-in-charge) 0.50 mm (+ 0.05 %) total coated thickness with zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length up to 12 metre or as desired by Engineering- charge. The sheet shall be fixed using self drilling /self tapping screws of size (5.5x 55 mm) with EPDM seal, complete up to any pitch in horizontal/ vertical or curved surfaces, excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required.

Providing and fixing precoated galvanized steel sheet roofing accessories 0.50 mm (+0.05 %) total coated thickness, Zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns using self drilling/ self tapping screws complete : Ridges plain (500 - 600mm)

15 mm cement plaster on the rough side of single or half brick wall of mix :1:4 (1 cement: 4 fine sand)

20 mm cement plaster of mix : 1:4 (1 cement: 4 fine sand)

6 mm cement plaster of mix : 1:3 (1 cement : 3 fine sand)

Distempering with oil bound washable distemper of approved brand and manufacture to give an even shade :New work (two or more coats) over and including water thinnable priming coat with cement primer

Finishing walls with textured exterior paint of required shade :New work (Two or more coats applied @ 3.28 ltr/10 sqm) over and including priming coat of exterior primer applied @ 2.20kg/10 sqm

Applying priming coat: With ready mixed red oxide zinc chromate primer of approved brand and manufacture on steel work (second coat)

Painting with synthetic enamel paint of approved brand and manufacture to give an even shade : Two or more coats on new work

French spirit polishing :Two or more coats on new works including a coat of wood filler

Providing and laying at or near ground level factory made kerb stone of M-25 grade cement concrete in position to the required line, level and curvature, jointed with cement mortar 1:3 (1 cement: 3 coarse sand), including making joints with or without grooves (thickness of joints except at sharp curve shall not to more than 5mm), including making drainage opening wherever required complete etc. as per direction of Engineer-in-charge (length of finished kerb edging shall be measured for payment). (Precast C.C. kerb stone shall be approved by Engineer-in-charge).

Construction of granular sub-base by providing close graded Material conforming to specifications, mixing in a mechanical mix plant at OMC, carriage of mixed material by tippers to work site, for all leads & lifts, spreading in uniform layers of specified thickness with motor grader on prepared surface and compacting with vibratory power roller to achieve the desired density, complete as per specifications and directions of Engineer-in-Charge. With material conforming to Grade-I (size range 75 mm to 0.075 mm) having CBR Value-30

Providing, laying, spreading and compacting graded stone aggregate (size range 53 mm to 0.075 mm ) to wet mix macadam (WMM) specification including premixing the material with water at OMC in for all leads & lifts, laying in uniform layers with mechanical paver finisher in sub- base / base course on well prepared surface and compacting with vibratory roller of 8 to 10 tone capacity to achieve the desired density, complete as per specifications and directions of Engineer-in-Charge.

Providing and laying factory made chamfered edge Cement Concrete paver blocks in footpath, parks, lawns, drive ways or light traffic parking etc., of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over 50mm thick compacted bed of sand, compacting and proper embedding/laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand. complete all as per direction of Engineer-in-Charge - 60mm thick cement concrete paver block of M-35 grade with approved colour, design & pattern.

Providing and laying factory made chamfered edge Cement Concrete paver blocks in footpath, parks, lawns, drive ways or light traffic parking etc., of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over 50mm thick compacted bed of sand, compacting and proper embedding/laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand. complete all as per direction of Engineer-in-Charge - 80 mm thick C.C. paver block of M-30 grade with approved color design and pattern.

Constructing of circular type manhole 0.91 m internal dia at bottom and 0.56 m dia at top ,0.91 m deep and 600 mm dia S.F.R.C cover with frame (heavy duty,HD-20 grade designation) confirming to I.S 12592,, total weight of cover and frame to be not less than 182 kg brick masonry in cement mortar 1:4 (1 cement :4 coarse sand), in side cement plaster 12 mm thick with cement mortar 1:3 (1 cement : 3 coarse sand) finished with a floating coat of neat cement, foundation concrete 1:3:6 mix (1 cement : 3 coarse sand : 6 graded stone aggregate 40 mm nominal size), and making necessary channel in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) finished with a floating coat of neat cement, including earth work excavation and refilling with the excavated earth after completion of the work necessary water proofing and centering, shuttering etc. all complete as per as per drawing. (Sulphate resistant cement should be used for all cement works) - Plot manhole

Extra depth for circular type manhole 0.91m internal dia (at bottom) beyond 0.91 m to 1.67 m

Constructing of circular type manhole 1.22 m internal dia at bottom and 0.56 m dia at top and 1.68 m deep and 600 mm dia S.F.R.C cover with frame (heavy duty,HD-20 grade designation) confirming to I.S 12592,, total weight of cover and frame to be not less than 182 kg brick masonry in cement mortar 1:4 (1 cement :4 coarse sand) inside cement plaster 12 mm thick with cement mortar 1:3 (1 cement : 3 coarse sand) finished with a floating coat of neat cement foundation concrete 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 40 mm nominal size) and making necessary channel in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) finished with a floating coat of neat cement, including earth work excavation and refilling with the excavated earth after completion of the work necessary water proofing and centering, shuttering etc. all complete as per as per drawing.(Sulphate resistant cement should be used for all cement works)

Extra depth for circular type manhole 1.22m internal dia (at bottom) beyond 1.68 m to 2.29 m

Constructing of circular type manhole 1.52 m internal dia at bottom and 0.6 m dia at top and 2.30 m deep and 600 mm dia S.F.R.C cover with frame (heavy duty,HD-20 grade designation, fixed in cement concrete 1:2:4) confirming to I.S 12592,, total weight of cover and frame to be not less than 182 kg brick masonry brick masonry in cement mortar 1:4 (1 cement : 4 coarse sand) inside cement plaster 12 mm thick with cement mortar 1:3 (1 cement : 3 coarse sand) finished with a floating coat of neat cement, foundation concrete 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 40 mm nominal size) and making necessary channel in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) finished with a floating coat of neat cement, including earth work excavation and refilling with the excavated earth after completion of the work necessary water proofing and centering, shuttering etc. all completes per as per drawing. (Sulphate resistant cement should be used for all cement works)

Extra depth for circular type manhole 1.52m internal dia (at bottom) beyond 2.3 m

Providing orange colour safety foot rest of minimum 6 mm thick plastic encapsulated as per IS : 10910, on 12 mm dia steel bar conforming to IS: 1786, having minimum cross section as 23 mmx25 mm and over all minimum length 263 mm and width as 165 mm with minimum 112 mm space between protruded legs having 2 mm tread on top surface by ribbing or chequering besides necessary and adequate anchoring projections on tail length on 138 mm as per standard drawing and suitable to with stand the bend test and chemical resistance test as per specifications and having manufacture's permanent identification mark to be visible even after fixing, including fixing in manholes with 30x20x15 cm cement concrete block 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) complete as per design

Providing sand cast iron drop connection externally for 60 cm drop from branch sewer line to main sewer manhole including inspection and cleaning eye with chain and lid, sand cast iron drop pipe and bend encased all-round with cement concrete 1:5:10 (1 cement : 5 fine sand : 10 graded stone aggregate 40 mm nominal size) with all centering and shuttering required, cutting holes in walls and making good with brick work in cement mortar 1:4 (1 cement : 4 coarse sand) plastered with cement mortar 1:3 (1 cement : 3 coarse sand) on inside of the manhole wall, lead caulked joints between sand cast iron pipes and fittings, stiff cement mortar 1:1 (1 cement : 1 fine sand) joints between sand cast iron tee and S.W. pipe, making required channels complete as per standard design and specifications : 150 mm dia sand cast iron drop connection

Extra for depths beyond 60 cm of sand cast iron drop connection complete :For 150 mm dia sand cast iron drop connection

Providing and laying Non Pressure NP-3 class (Medium duty) R.C.C. pipes including collars/spigot jointed with stiff mixture of cement mortar in the proportion of 1:2 (1 cement : 2 fine sand) including testing of joints etc. complete - 450mm dia

Providing and laying Non Pressure NP-3 class (Medium duty) R.C.C. pipes including collars/spigot jointed with stiff mixture of cement mortar in the proportion of 1:2 (1 cement : 2 fine sand) including testing of joints etc. complete - 600mm dia

Providing and laying Non Pressure NP-3 class (Medium duty) R.C.C. pipes including collars/spigot jointed with stiff mixture of cement mortar in the proportion of 1:2 (1 cement : 2 fine sand) including testing of joints etc. complete - 900mm dia

Boring, providing and installation bored cast-in-situ reinforced cement concrete piles 450mm dia of grade M-25 of specified diameter and length below the pile cap, to carry a safe working load not less than specified, excluding the cost of steel reinforcement but including the cost of boring with bentonite solution and temporary casing of appropriate length for setting out and removal of same and the length of the pile to be embedded in the pile cap etc. by percussion drilling using Direct mud circulation (DMC) or Bailer and chisel technique by tripod and mechanical Winch Machine all complete, including removal of excavated earth with all its lifts and leads (length of pile for payment shall be measured up to bottom of pile cap).

Boring, providing and installation bored cast-in-situ reinforced cement concrete piles 500mm dia of grade M-25 of specified diameter and length below the pile cap, to carry a safe working load not less than specified, excluding the cost of steel reinforcement but including the cost of boring with bentonite solution and temporary casing of appropriate length for setting out and removal of same and the length of the pile to be embedded in the pile cap etc. by percussion drilling using Direct mud circulation (DMC) or Bailer and chisel technique by tripod and mechanical Winch Machine all complete, including removal of excavated earth with all its lifts and leads (length of pile for payment shall be measured up to bottom of pile cap).

Vertical load testing of piles in accordance with IS 2911 (Part IV) including installation of loading platform by Kentledge/Anchor piles method and preparation of pile head or construction of test cap and dismantling of test cap after test etc. complete as per specification & the direction of Engineer in-charge. Note: 1. Initial and Routine Load Test shall not be carried out by Dynamic method of testing. Note: 2. Testing agency shall submit the design of loading platform for the approval of Engineer-in-charge. Single pile up to 50 tone Safe capacity Routine test (Test Load 1.5 times the Safe capacity)

Vertical load testing of piles in accordance with IS 2911 (Part IV) including installation of loading platform by Kentledge/Anchor piles method and preparation of pile head or construction of test cap and dismantling of test cap after test etc. complete as per specification & the direction of Engineer in-charge. Note: 1. Initial and Routine Load Test shall not be carried out by Dynamic method of testing. Note: 2. Testing agency shall submit the design of loading platform for the approval of Engineer-in-charge. Single pile above 50 tone and up to 100 tone Safe capacity Initial test (Test Load 2.5 times the Safe capacity)

Providing and applying fiber reinforced elastomeric liquid water proofing membrane with resilient acrylic polymers having Sun Reflectivity Index (SRI) of 105 on top of concrete roof in three coats @10.76 litre/ 10 sqm. One coat of self-priming of elastomeric waterproofing liquid (dilution with water in the ratio of 3:1) and two coats of undiluted elastomeric waterproofing liquid (dry film thickness of complete application/system not less than 500 microns). The operation shall be carried out after scrapping and properly cleaning the surface to remove loose particles with wire brushes, complete in all respect as per the direction of Engineer-in-Charge.

Design supply & installation of suspended Spider Glazing system designed to withstand the wind pressure as per IS 875 (Part-III). The Suspended System held with Spider Fittings of SS-316 Grade Steel of approved manufacturer with glass panel having 12 mm thick clear toughened glass held together with SS- 316 Grade Stainless steel Spider & bolt assembly with laminated glass fins 21 mm thick. The Glass fins and glass panel assembly shall be connected to Slab/ beams by means of SS- 316 Grade stainless steel brackets & Anchor bolts and at the bottom using SS channel of 50x25x2mm using fastener & anchor bolts, non staining weather sealants of approved make, Teflon/ nylon bushes and separators to prevent bi-metallic contacts, all complete to perform as per specification and approved drawings. The complete system to be designed to accommodate thermal expansion & seismic movements etc. The joints between glass panels (6 to 8 mm) and gaps at the perimeter & in U channel of the assembly to be filled with non staining weather sealant, so as to make the entire system fully water proof & dust proof. The rate shall include all design, Engineering and shop drawing including approval from structural designer, labour, T&P, scaffolding, other incidental charges including wastage, enabling temporary services all fitting fixers nut bolts, washer, Buffer plates, fastener, anchors, SS channel laminated glass etc. all complete. For the purpose of payment, actual elevation area of Glazing including thickness of joints and the portion of Glass panel inside the SS channel shall be measured.

Providing and fixing false ceiling at all heights with integral densified calcium silicate reinforced with fiber and natural filler false ceiling tiles of Size 595x595mm of approved texture, design and patterns as per CPWD Specification 2019, to be laid in true horizontal level suspended on inter-locking metal T-Grid of hot dipped galvanized iron section of 0.33mmthick (galvanized @ 120 grams per sqm including both sides)comprising of main-T runners of size 24x38 mm of length 3000 mm, cross - T of size 24x32 mm of length 1200 mm and secondary intermediate cross-T of size 24x32 mm of length 600mm to form grid module of size 600 x 600 mm, suspended from ceiling using galvanised mild steel items (galvanizing @ 80 grams per sqm) i.e. 12x50 mm long dash fasteners, 6 mm dia fully threaded hanger rod up to 1000 mm length and L-shape level adjuster of size 76x25x25x1.6 mm fixed with grid and Z cleat of size 25x37x25x1.6mm thick with pre-cut hole on both 25mm flange to pierce into 12x50mm or even bigger size dash fastener if require, fixed with Galvanized iron perimeter wall angle or size 24x24x0.40 mm of length 3000 mm to be fixed on periphery wall / partition with the help of plastic rawl plugs at 450mm center to center and 40 mm long dry wall S.S screws. The work shall be carried out as per specifications, drawing and as per directions of the Engineer-in- Charge. With 15 mm thick Tegular edged light weight calcium silicate false ceiling tiles

Providing and fixing Double shutter fully glazed doors with 12mm toughened glass (Make Fittings- Dorma / Geze / Approved make and vendor to provide detail shop drawing and approved by Architect) - up to floor VI level. Floor spring BTS 75V EN 1-4 with std. spindle and cover plate. The floor spring with back check and adjustable closing speed from 175°. Non-hold open with PT Standard Patch fittings including PT20 Bottom patch, PT10 Top Patch, PT24 Top Pivot, US10 Corner lock & LKP. As per EN 1154 and CE marked. Finish: Satin stainless steel.

Providing and fixing 110mm dia (6kgf/Cm2) PVC pipes for Weep holes in 150mm/200mm thick RCC wall including's jointing of pipes with one step PVC solvent cement ..etc. complete as per direction of engineer in charge.

NAT GHAR- Design, Supply, Fabrication and Installation of Membrane Panels & steel Cables and GI corner fittings nuts and bolts and associated accessories with membrane works. The design complies with the requirements of BS and, EU Standards. The tensioned membrane structure shall include engineering design of structural members and accessory parts. Membrane system shall include Membrane Fabric, Wire Ropes and Cables, Shackles, Rigging Screws, Clamps and tensioning hardware. Providing, fabricating, assembling and erection of pre stressed Tensile Membrane Fabric structure in desired profile as per drawing , with TX 30 Type II colour coated with SERGE FERRARI FABRIC or MEHLER FABRIC or equivalent to , over steel frames with all fittings and fixtures such as Galvanized MS Membrane /End Plate ,Shackles, Rigging Screws , Turnbuckles, swage terminals, fork , keder rods & galvanized MS wire ropes /cables with stainless steel end terminals complete as per Drawing / Detail & as per technical specifications and as per the instructions of Engineer-in-charge. Supply of Steel ,Fabrication, Erection , Assembling, hoisting, erecting and placing in position MS trussed, ,I Beam Support , Rectangular Tubes ,rafters, purlins, bracing tubular Structure made from Steel hollow sections, ISI marked conforming Yst 240, thickness up to 10mm (TATA/JINDAL/ APPOLO) in the profile shape as per drawings with special plate connector, pinion joints, Plates, hollow sections etc. using water jet 3-D cutting system for obtaining smooth 3-dimensional curvature, SAW/MMAW/MIG welding process with special plate connectors, pinion joints, plates, hollow sections with cleaning the surface and applying a coat of epoxy primer and including Preparation of detailed fabrication and erection drawings of Structural steel work from the approved design, transportation to the site, cutting , threading, machining, leads and lifts up to all heights, tools and plants and necessary scaffolding etc. required for all operations involved to make structure of Tensile Membrane shade. The tubular structure system with plate connectors, pinion joints, etc. is to be provided. The structure has to be provided as per conceptual drawings of Tensile fabric profile, including all arch beam, curved lateral beams and bracings, vertical support columns, nodal joints, bases of columns and high tensile bolts of grade not less than 10.9 having black phosphate coating.

KALA KENDRA :- Design, Supply, Fabrication and Installation of Membrane Panels & steel Cables and GI corner fittings nuts and bolts and associated accessories with membrane works. The design complies with the requirements of BS and, EU Standards. The tensioned membrane structure shall include engineering design of structural members and accessory parts. Membrane system shall include Membrane Fabric, Wire Ropes and Cables, Shackles, Rigging Screws, Clamps and tensioning hardware. Providing, fabricating, assembling and erection of pre stressed Tensile Membrane Fabric structure in desired profile as per drawing , with TX 30 Type II colour coated with SERGE FERRARI FABRIC or MEHLER FABRIC or equivalent to , over steel frames with all fittings and fixtures such as Galvanized MS Membrane /End Plate ,Shackles, Rigging Screws , Turnbuckles, swage terminals, fork , keder rods & galvanized MS wire ropes /cables with stainless steel end terminals complete as per Drawing / Detail & as per technical specifications and as per the instructions of Engineer-in-charge. Supply of Steel , , Assembling, hoisting, erecting and placing in position MS trussed, ,I Beam Support , Rectangular Tubes ,rafters, purlins, bracing tubular Structure made from Steel hollow sections, ISI marked conforming Yst 240, thickness up to 10mm (TATA/JINDAL/ APPOLO) in the profile shape as per drawings with special plate connector, pinion joints, Plates, hollow sections etc. using water jet 3-D cutting system for obtaining smooth 3-dimensional curvature, SAW/MMAW/MIG welding process with special plate connectors, pinion joints, plates, hollow sections with cleaning the surface and applying a coat of epoxy primer and including Preparation of detailed fabrication and erection drawings of Structural steel work from the approved design, transportation to the site, cutting , threading, machining, leads and lifts up to all heights, tools and plants and necessary scaffolding etc. required for all operations involved to make structure of Tensile Membrane shade. The tubular structure system with plate connectors, pinion joints, etc. is to be provided. The structure has to be provided as per conceptual drawings of Tensile fabric profile, including all arch beam, curved lateral beams and bracings, vertical support columns, nodal joints, bases of columns and high tensile bolts of grade not less than 10.9 having black phosphate coating.

Providing soil stabilization with 4% of hydrated lime of 150mm thick below foundation concrete, including levelling and ramming each layer up to finished level etc. all complete and as directed by the Engineer-in-charge.

Supplying and fixing MS manhole ventilating shaft pipe of 200 mm at bottom and 100 mm at top to a height of 7.60 m confirming to IS 1239/3589 including earth work excavation, the cost for laying PCC in 1:2:4 using 20 mm hard broken stone over a finished layer of PCC 1:4:8 using 40 mm hard broken stone etc. complete as per drawing.

Supplying and laying 160mm dia uPVC pipes class SN 8, SDR-34, confirming to IS 15328-2003 and relevant specials including packing the joints with rubber /lubricant fixing ,holding wherever necessary and making good of the dismantled portion with necessary connections etc., complete in all respects and as per drawing. (Below Ground level)

Supply, laying, testing & commissioning of 'B' class heavy duty G.I. pipe conforming to IS 1239 including welding, fittings like elbows, tees, flanges, tapers, nuts, bolts, gaskets etc. and fixing the pipe on the wall/ceiling with suitable clamp/support frame and painting with two or more coats of synthetic enamel paint of required shade complete as required.- 100mm dia pipe

Supply, laying, testing & commissioning of 'B' class heavy duty G.I. pipe conforming to IS 1239 including welding, fittings like elbows, tees, flanges, tapers, nuts, bolts, gaskets etc. and fixing the pipe on the wall/ceiling with suitable clamp/support frame and painting with two or more coats of synthetic enamel paint of required shade complete as required.- 50mm dia drain line

Supply, laying, testing & commissioning of 'B' class heavy duty G.I. pipe conforming to IS 1239 (1 Mtrs below ground level) including welding, fittings like elbows, tees, flanges, tapers, nuts, bolts, gaskets etc. and fixing the pipe on the wall/ceiling with suitable clamp/support frame and painting with two or more coats of synthetic enamel paint of required shade complete as required - 100m dia pipe

Supply, fixing, testing and commissioning of butterfly valve of PN 1.6 rating with bronze/gunmetal seat duly ISI marked complete with nuts, bolts, washers, gaskets conforming to IS 13095 of following sizes as required : 100m dia

Providing, Laying, Testing and commissioning of 250 mm dia RCC pipes of NP2 class hume pipes

Supplying and fixing of 40m length first-aid Hose Reel with MS construction spray painted (single headed internal hydrant valve) in post office red, conforming to IS 884 complete with the following as required. A) 20 mm nominal internal dia water hose thermoplastic (Textile reinforced) type -2 as per IS: 12585 B) 20 mm nominal internal dia gun metal globe valve & nozzle. C) Drum and brackets for fixing the equipment's on wall. D) Connections from riser with 25 mm dia stop gun metal valve & M.S. Pipe and socket.

Supply & fixing of air release valve (25mm) at the top of each floor of the riser with drain connection and the rates shall include all the accessories

Supply, Installation, Testing & Commissioning of 4 Kg capacity of ABC type fire extinguisher ISI marked conforming to IS: 15683, complete with delivery hose horn, wheel type release valve, locking arrangement, operation manual and bracket with suitable fixture.

Supply, Installation, Testing & Commissioning of 4.5 Kg capacity of CO2 type fire extinguisher ISI marked conforming to IS: 15683, complete with delivery hose horn, wheel type release valve, locking arrangement, operation manual and bracket with suitable fixture.

Supplying, installation, testing & commissioning of repeater panel with 320 character/ Touch screen LCD display with inbuilt reset, acknowledge and silence switches complete as required.

Supplying, installation, testing & commissioning of intelligent analogue addressable photothermal detector complete with mounting base complete as required.

Supplying, installation, testing & commissioning of response indicator on surface/recessed MS Box having two LED, metallic cover complete with all connections etc. as required.

Supplying, installation, testing & commissioning of intelligent addressable programmable sounder complete as required.

Supplying, installation, testing & commissioning of fault isolator complete with base as required.

Supplying, installation, testing & commissioning of addressable fire control module complete as required.

Supplying, installation, testing & commissioning of addressable beam detector with short circuit isolator (inbuilt or separate) complete with emitter and receiver including connections with remote test features etc. complete as required.

Supplying, installation, testing & commissioning of intelligent addressable duct detector including suitable Photo detector complete with base as required.

Supplying, installation, testing & commissioning of addressable manual call point complete as required.

Supplying, installation, testing & commissioning of addressable horn cum strobe complete as required.

Supplying & laying of 2x1.5 sqmm fire alarm armoured cable, 600/1000V rated with annealed copper conductor having XLPE insulation, steel wire armoring & FRLS outer sheath complete as required. (a) 2c x 1.5 sq. mm unarmoured cable

Providing and fixing white vitreous china pedestal type water closet (European type) with seat and lid, 10 litre low level white vitreous china flushing cistern & C.P. flush bend with fittings & C.I. brackets, 40 mm flush bend, overflow arrangement with specials of standard make and mosquito proof coupling of approved municipal design complete, including painting of fittings and brackets, cutting and making good the walls and floors wherever required : W.C. pan with ISI marked white solid plastic seat and lid

Providing and fixing water closet squatting pan (Indian type W.C. pan ) with 100 mm sand cast Iron P or S trap, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever) conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required: White Vitreous china Orissa pattern W.C. pan of size 580x440 mm with integral type foot rests

Providing and fixing white vitreous china flat back or wall corner type lipped front urinal basin of 430x260x350 mm and 340x410x265 mm sizes respectively with automatic flushing cistern with standard flush pipe and C.P. brass spreaders with brass unions and G.I clamps complete, including painting of fittings and brackets, cutting and making good the walls and floors wherever required : One urinal basin with 5 litre white P.V.C. automatic flushing cistern

Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require: White Vitreous China Wash basin size 630x450 mm with a pair of 15 mm C.P. brass pillar taps

Providing and fixing Stainless Steel A ISI 304 (18/8) kitchen sink as per IS:13983 with C.I. brackets and stainless steel plug 40 mm, including painting of fittings and brackets, cutting and making good the walls wherever required : Kitchen sink with drain board 510x1040 mm bowl depth 250 mm

Providing and fixing white vitreous china laboratory sink with C.I. brackets, C.P. brass chain with rubber plug, 40 mm C.P brass waste and 40mm C.P. brass trap with necessary C.P. brass unions complete, including painting of fittings and brackets, cutting and making good the wall wherever required :

Providing and fixing mirror of superior glass (of approved quality) and of required shape and size with plastic moulded frame of approved make and shade with 6 mm thick hard board backing : Circular shape 450 mm dia

Providing and fixing PTMT soap Dish Holder having length of 138mm, breadth 102mm, height of 75mm with concealed fitting arrangements, weighing not less than 106 gms.

Providing and fixing toilet paper holder : Vitreous china

Providing and fixing brass bib cock of approved quality : 15 mm nominal bore

Providing and fixing PTMT grating of approved quality and colour. Circular type 100 mm nominal dia

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings This includes jointing of pipes & fittings with one step CPVC solvent cement, trenching, refilling & testing of joints complete as per direction of Engineer in Charge. (A) Exposed or in trenches 20 mm nominal outer dia pipe

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings This includes jointing of pipes & fittings with one step CPVC solvent cement, trenching, refilling & testing of joints complete as per direction of Engineer in Charge. (A) Exposed or in trenches 25 mm nominal outer dia pipe

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings This includes jointing of pipes & fittings with one step CPVC solvent cement, trenching, refilling & testing of joints complete as per direction of Engineer in Charge. (A) Exposed or in trenches 32 mm nominal outer dia pipe

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings This includes jointing of pipes & fittings with one step CPVC solvent cement, trenching, refilling & testing of joints complete as per direction of Engineer in Charge. (A) Exposed or in trenches 40 mm nominal outer dia pipe

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings This includes jointing of pipes & fittings with one step CPVC solvent cement, trenching, refilling & testing of joints complete as per direction of Engineer in Charge. (A) Exposed or in trenches 50mm dia pipe

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings This includes jointing of pipes & fittings with one step CPVC solvent cement, trenching, refilling & testing of joints complete as per direction of Engineer in Charge. (B) Concealed pipe with cutting chases & making good the walls 20 mm nominal outer dia pipe

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings This includes jointing of pipes & fittings with one step CPVC solvent cement, trenching, refilling & testing of joints complete as per direction of Engineer in Charge. (B) Concealed pipe with cutting chases & making good the walls 25 mm nominal outer dia pipe

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings This includes jointing of pipes & fittings with one step CPVC solvent cement, trenching, refilling & testing of joints complete as per direction of Engineer in Charge. (B) Concealed pipe with cutting chases & making good the walls 32 mm nominal outer dia pipe

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings This includes jointing of pipes & fittings with one step CPVC solvent cement, trenching, refilling & testing of joints complete as per direction of Engineer in Charge. (B) Concealed pipe with cutting chases & making good the walls 40 mm nominal outer dia pipe

Providing and fixing ball valve (brass) of approved quality, High or low pressure, with plastic floats complete : 20 mm nominal bore

Providing and fixing ball valve (brass) of approved quality, High or low pressure, with plastic floats complete : 25 mm nominal bore

Providing and fixing gun metal non- return valve of approved quality (screwed end) : 32 mm nominal bore

Providing and fixing gun metal non- return valve of approved quality (screwed end) : 40 mm nominal bore

Providing and fixing gun metal non- return valve of approved quality (screwed end) : 50mm nominal bore

Providing and fixing square-mouth S.W. gully trap class SP-1 complete with C.I. grating brick masonry chamber with water tight C.I. cover with frame of 300 x300 mm size (inside) the weight of cover to be not less than 4.50 kg and frame to be not less than 2.70 kg as per standard design: With common burnt clay F.P.S. (non modular) bricks of class designation 7.5

Constructing brick masonry manhole in cement mortar 1:4 ( 1 cement : 4 coarse sand ) with R.C.C. top slab with 1:1.5:3 mix (1 cement : 1.5 coarse sand (zone-III) : 3 graded stone aggregate 20 mm nominal size), foundation concrete 1:4:8 mix (1 cement : 4 coarse sand (zone-III) : 8 graded stone aggregate 40 mm nominal size), inside plastering 12 mm thick with cement mortar 1:3 (1 cement : 3 coarse sand) finished with floating coat of neat cement and making channels in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) finished with a floating coat of neat cement complete as per standard design : Inside size 120x90 cm and 90 cm deep including C.I. cover with frame (heavy duty) 560 mm internal diameter, total weight of cover and frame to be not less than 208 kg (weight of cover 108 kg and weight of frame 100 kg) : With common burnt clay F.P.S. (non modular) bricks of class designation 7.5

Supplying , laying of 75mm dia UPVC Pipes (0.6Mpa) with all necessary fittings in exposed/Concealed etc. complete as directed by Engineer- in- charge

Supplying , laying of 110mm dia UPVC Pipes (0.6Mpa) with all necessary fittings in exposed/Concealed etc. complete as directed by Engineer- in- charge

Providing and laying Double Flanged (Screwed/ Welded) Centrifugally (Spun) Ductile Iron Pipes of Class K - 7 conforming to IS : 8329 complete as per direction of Engineer in Charge 100 mm dia Ductile Iron Class K-7 pipe for potable water pumping main

Providing, laying, testing & commissioning of MS pipe conforming to IS 3589/IS 1239 including welding, fittings like elbows, tees, flanges, tapers, nuts, bolts, gaskets etc. and fixing the pipe on the wall/ceiling with suitable clamps, support frame and painting twith two or more coats of synthetic enamel paint of required shade complete as required as per direction of Engineer in Charge. (For pump room) - 100mm dia

Providing and fixing C.I. sluice valves complete with bolts, nuts, rubber insertions etc. complete as per direction of Engineer in Charge. - 100mm dia

Providing and fixing C.I. double acting air valve of approved quality with bolts, nuts rubber insertions etc. complete as per direction of Engineer in Charge - 40 mm valve on up to 100 mm.dia. Pipe, rating 10kg/cm2

Providing and fixing gun metal non-return valve of approved quality (screwed end): Tapping from potable water network for landscaping - 25 mm nominal bore

Providing and laying non-pressure NP2 class (light duty) R.C.C. pipes with collars jointed with stiff mixture of cement mortar in the proportion of 1:2 (1 cement : 2 fine sand) including testing of joints etc. complete : 250mm dia pipe

Excavating trenches of required width for pipes, cables, etc. including excavation for sockets, and dressing of sides, ramming of bottoms, depth up to 1.5 m, including getting out the excavated soil. and then returning the soil as required, in layers not exceeding 20 cm in depth, including consolidating each deposited layer by ramming, watering, etc. and disposing of surplus excavated soil as directed, within a lead of 50 m: Pipes, cables etc. exceeding 80 mm dia but not exceeding 300 mm dia

Constructing masonry Chamber 120x120x100 cm inside, in brick work in cement mortar 1:4 (1 cement : 4 coarse sand) for sluice valve, with C.I. surface box 100 mm top diameter, 160 mm bottom diameter and 180 mm deep ( inside) with chained lid and RCC top slab 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) , i/c necessary excavation, foundation concrete 1:5:10 (1 cement : 5 fine sand : 10 graded stone aggregate 40 mm nominal size) and inside plastering with cement mortar 1:3 (1 cement : 3 coarse sand) 12 mm thick, finished with a floating coat of neat cement complete as per standard design : of class designation 7.5

Supply, Installation, testing and commissioning of horizontal centrifugal monobloc pump for pumping water from underground sump to overhead tank, of capacity 375 LPM Each Pump and 20 m head each and electric control panel board (Operating 1 pump at a time) with cyclic timer, dry run protection, required electrical and control wiring from panel to pump and also including supply and fixing the required butter fly valves, non return valves, Pressure gauge at each pump outlet of 150mm dial, 1/2" NPTM bottom connection, measuring element 316 SS diaphragm suitable to measure the discharge header pressure & pump discharge line pressure (0 to 10 kg/Sq cm) etc. including the cost for the required length of pipes including the cost required for support for header pipes, discharge pipes for each pump and for common discharge pipes and including the cost for the required dismantling joints on either side of the pumps,as per manufacturer specifications etc. complete and with all accessories like common base plate with suction and discharge manifold complete and as directed by the engineer in charge.

Supplying and fixing of 100mm dia electromagnetic flow meter consisting of, transducer, transmitter, microprocessor based flow computer cum integrator with local L C D indicator, complete with bolts, nuts, rubber insertions etc. including all hardware/accessories required for erection, testing and commissioning. (including adaptor AC/DC complete as per direction of Engineer in Charge.

Supplying and laying of HDPE pipes,PE-100 Grade, PN6 pressure rating for water supply conforming to IS 4984 UV stabilized & anti-microbial fusion welded, having thermal stability including all fittings, testing of joints complete as per direction of Engineer in Charge.110mm dia

Supplying, installation, testing and commissioning of diesel engine driven main fire pump suitable for automatic operation and consisting of following, complete in all respects, as required : (Diesel Driven Pump). Horizontal type, multistage, centrifugal pump of cast of iron body and bronze impeller with stainless steel shaft, mechanical seal conforming to IS 1520. Discharge of 2850 lpm at a pressure of 70 mtr directly coupled to suitable HP, 1500 RPM water cooled with radiator, diesel engine conforming to relevant IS standard complete with auto starting mechanism, 12 /24 volts electric starting equipment, diesel tank, exhaust pipe extended up to 10 m outside pump house duly insulated with 50 mm thick glass wool with 1.0 mm thick aluminium sheet cladding, residential silencer, instruments and protection as per standard specification, stop solenoid for auto stop in the event of fault with audio indications, painted with post office red colour etc. as required. M.S fabricated, common base plate, coupling, coupling guard, foundation bolts etc. as required. Suitable cement concrete foundation duly plastered and with anti vibration pads.

Supplying, installation, testing and commissioning of Electric driven Main Fire Pump suitable for automatic operation and consisting of following, complete in all respects, as required Horizontal type, multistage, centrifugal, split casing pump of cast iron body & bronze impeller with stainless steel shaft, mechanical seal conforming to IS 1520. Discharge of 2850 lpm at a pressure of 70 mtr directly coupled to suitable HP Squirrel cage induction motor, TEFC, synchronous speed 1500 RPM, suitable for operation on 415 volts, 3 phase 50 Hz, AC supply with IP 55 protection for enclosure, horizontal foot mounted type with Class-'F' insulation, conforming to IS-325. M.S. fabricated Common base plate, coupling, coupling guard, foundation bolts etc. as required. Suitable cement concrete foundation duly plastered with anti vibration pads.

Supplying, installation, testing and commissioning of electric driven pressurization pump suitable for automatic operation and consisting of following, complete in all respects, as required : (Jockey Pump) Horizontal type, multistage, centrifugal pump of cast iron body and bronze impeller with stainless steel shaft, mechanical seal conforming to IS : 1520. Discharge of 180 lpm at a pressure of 70 mtr directly coupled to suitable HP squirrel cage induction motor TEFC type suitable for operation on 415 volts, 3 phase 50 Hz AC supply with IP 55 class of protection for enclosure, horizontal foot mounted type with Class-'F' insulation, conforming to IS : 325.M.S.fabricated Common base plate, coupling, coupling guard, foundation bolts etc. as required. Suitable cement concrete foundation duly plastered and with anti vibration pads.

Supply, fixing, testing and commissioning of butterfly valve of PN 1.6 rating with bronze/gunmetal seat duly ISI marked complete with nuts, bolts, washers, gaskets conforming to IS 13095 of following sizes as required : 150mm dia

Supply, fixing, testing and commissioning of butterfly valve of PN 1.6 rating with bronze/gunmetal seat duly ISI marked complete with nuts, bolts, washers, gaskets conforming to IS 13095 of following sizes as required : 100mm dia

Supply, fixing, testing and commissioning of butterfly valve of PN 1.6 rating with bronze/gunmetal seat duly ISI marked complete with nuts, bolts, washers, gaskets conforming to IS 13095 of following sizes as required : 80mm dia

Supply, fixing, testing and commissioning of butterfly valve of PN 1.6 rating with bronze/gunmetal seat duly ISI marked complete with nuts, bolts, washers, gaskets conforming to IS 13095 of following sizes as required : 50mm dia

Providing, installation, testing and commissioning of non-return valve of following sizes confirming to IS: 5312 complete with rubber gasket, GI bolts, nuts, washers etc. As required : 150mm dia

Providing, installation, testing and commissioning of non-return valve of following sizes confirming to IS: 5312 complete with rubber gasket, GI bolts, nuts, washers etc. As required : 80mm dia

Providing, installation, testing and commissioning of stainless steel Y-strainer fabricated out of 1.6 mm thick stainless steel, Grade 304, sheet with 3 mm dia holes with stainless steel flange.

Test array arrangement for pump set with Pressure Switch , valves etc. Pressure Switch for 150mm Pipe line

Supplying and fixing air vessel made of 250 mm dia, 8 mm thick MS sheet, 1200 mm in height with air release valve on top and flanged connection to riser, drain arrangement with 25 mm dia gun metal wheel valve with required accessories, pressure gauge and painting with synthetic enamel paint of approved shade as required.

a. Supplying and fixing of 4 Way fire brigade connection of cast iron body with gun metal male instantaneous inlet couplings complete with cap and chain as reqd. for suitable dia pipe connection conforming to IS 904 as required : b. 1 no. 150mm Butterfly Valve for Hyd system

Supply, laying, testing & commissioning of 'B' class heavy duty G.I. pipe conforming to IS 1239 including welding, fittings like elbows, tees, flanges, tapers, nuts, bolts, gaskets etc. and fixing the pipe on the wall/ceiling with suitable clamp/support frame and painting with two or more coats of synthetic enamel paint of required shade complete as required (Above Ground) - 150mm dia

Supply, laying, testing & commissioning of 'B' class heavy duty G.I. pipe conforming to IS 1239 (1 Mtrs below ground level) including welding, fittings like elbows, tees, flanges, tapers, nuts, bolts, gaskets etc. and fixing the pipe on the wall/ceiling with suitable clamp/support frame and painting with two or more coats of synthetic enamel paint of required shade complete as required (Under Ground) - 150mm dia

Supply and installation of Cast Iron Butterfly valve (100mm) including making flanged joints by providing necessary nuts, bolts, gaskets(1.5 mm CAF)etc. All complete as per specification.

Supply and installation of Cast Iron Non - Return Valve (100mm) including making flanged joints by providing necessary nuts, bolts, gaskets etc. All complete as per specification.

Supply and installation of 'Y' Strainer (100mm) including making flanged joints by providing necessary nuts, bolts, gaskets etc. All complete as per specification.

Supplying and fixing, testing and commissioning of Single headed external yard hydrant valve with 1 No. 63 mm dia instantaneous FM Gunmetal coupling and cast iron wheel, ISI marked, conforming to IS 5290 (type A) with blank Gunmetal cap and chain with necessary accessories etc.,. and the following - 63 mm dia single head landing valve (Stainless Steel)

Supplying and fixing, testing and commissioning of Single headed external yard hydrant valve with 1 No. 63 mm dia instantaneous FM Gunmetal coupling and cast iron wheel, ISI marked, conforming to IS 5290 (type A) with blank Gunmetal cap and chain with necessary accessories etc.,. Hose pipe 63 mm dia 15 m.long with male and female coupling at both ends

Supplying and fixing, testing and commissioning of Single headed external yard hydrant valve with 1 No. 63 mm dia instantaneous FM Gunmetal coupling and cast iron wheel, ISI marked, conforming to IS 5290 (type A) with blank Gunmetal cap and chain with necessary accessories etc.,.Branch pipe 63 mm dia with 20 mm (nominal internal diameter) nozzle and suitable for instantons connection

Supply, fixing, testing and commissioning of butterfly valve of PN 1.6 rating with bronze/gunmetal seat duly ISI marked complete with nuts, bolts, washers, gaskets conforming to IS 13095 of following sizes as required : 150mm dia

Supply, laying, testing & commissioning of 'B' class heavy duty G.I. pipe conforming to IS 1239 including welding, fittings like elbows, tees, flanges, tapers, nuts, bolts, gaskets etc. and fixing the pipe on the wall/ceiling with suitable clamp/support frame and painting with two or more coats of synthetic enamel paint of required shade complete as required (Above Ground) 80mm dia

Boring/drilling bore well of required dia for casing/ strainer pipe, by suitable method prescribed in IS: 2800 (part I), including collecting samples from different strata, preparing and submitting strata chart/ bore log, including hire & running charges of all equipment's, tools, plants & machineries required for the job, all complete as per direction of Engineer-in-charge, up to 90 metre depth below ground level. - Bore 300 mm dia

Supplying, assembling, lowering and fixing in vertical position in bore well unplasticized PVC medium well screen (RMS) pipes with ribs, conforming to IS: 12818, including hire & labour charges, fittings & accessories etc. all complete, for all depths, as per direction of Engineer-in charge

Development of tube well in accordance with IS : 2800 (part I) and IS: 11189, to establish maximum rate of usable water yield without sand content (beyond permissible limit), with required capacity air compressor, running the compressor for required time till well is fully developed, measuring yield of well by "V" notch method or any other approved method, measuring static level & draw down etc. by step draw down method, collecting water samples & getting tested in approved laboratory, i/c disinfection of tube well, all complete, including hire & labour charges of air compressor, tools & accessories etc., all as per requirement and direction of Engineer-in-charge. (For 2 borewell locations)

Supplying and fixing of DI wafer type butterfly valves, manually hand lever operated short body type and as per IS: 13095. M.O.C.: Body & Disc: DI, Body Liner: Nitrile Rubber, Shaft: SS 410, Flange Drilling as per IS 1538, PN 10 including all accessories complete as per direction of Engineer in Charge. 80mm dia butterfly valve

Providing and fixing C.I. double acting air valve confirming to IS 14845 of approved quality with bolts, nuts, rubber insertions damper proof design (PN 10 rating) with all jointing materials, gaskets, bolts, nuts, inclusive of dismantling pieces, washers, rubber gaskets complete as per direction of Engineer in charge - 50mm dia double acting air valve with Gate valve

Supplying, laying and jointing of 100 mm Unplasticized PVC column pipes 10 kg/cm² conforming to IS 4985-2000 or ASTM D 1785 (Diameter of pipes and pressure head as relevant to IS 4985), all uPVC pipe, including jointing of pipes with sure-loc joints or threaded joints & threaded fittings, testing of joints complete as per direction of Engineer in Charge. (Bore well pump outlet up to ground level).100mm uPVC pipe

Supply, installation testing & commissioning of Borewell submersible pump for borewell of capacity 315 LPM and 66 m head each (approximately 8 HP pump set) along with all necessary accessories like strainer, pressure gauge including cable 3 C, 4 sq.mm copper conductor pvc insulated cable suitable for submersible pump set operation and with manufacturer's standard control panel board which is mandatory and other required supporting items like SS hose nipple, nylon rope, clamps, bolt and nuts, GI nipple, 40 mm dia HDPE hose of required length etc. including all accessories complete as directed by the engineer in charge.

Supplying, laying and jointing of 80 mm Unplasticized PVC column pipes 10 kg/cm² conforming to IS 4985-2000 or ASTM D 1785 (Diameter of pipes and pressure head as relevant to IS 4985), all uPVC pipe, including jointing of pipes with sure-loc joints or threaded joints & threaded fittings, testing of joints complete as per direction of Engineer in Charge. 80mm uPVC pipe

Supply and fixing of Electromagnetic Flow meter shall be a velocity sensing Electromagnetic type, microprocessor based signal converter, sealed housing, flanged tube meter for 1.0 Mpa working pressure, manufactured to highest standard available for mag-meters, equipped with minimum six digit digital totalizers: Body SS 304 – Pulse Output 265V, 50hz AC – 4 -20mA Communication RS 485 – Connection Flange CS To IS 2062 – Electrode SS 316L – with Ebonite Rubber Lining - Field mount including all hardware/accessories required for erection, testing and commissioning as per direction of Engineer in Charge 80 mm dia. Electromagnetic Flow meter

Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit, with modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm. FRLS PVC insulated copper conductor single core cable etc. as required.

Wiring for twin control light point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit, 2 way modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm. FRLS PVC insulated copper conductor single core cable etc. as required.

Wiring for light/ power plug with 2X4 sq. mm FRLS PVC insulated copper conductor single core cable in surface/ recessed medium class PVC conduit along with 1 No 4 sq. mm FRLS PVC insulated copper conductor single core cable for loop earthing as required.

Wiring for circuit/ submain wiring along with earth wire with the 2x1.5 sq.mm + 1x1.5 sq.mm earth wire sizes of FRLS PVC insulated copper conductor, single core cable in surface / recessed medium class PVC conduit as required

Wiring for circuit/ submain wiring along with earth wire with the 2X 2.5 sq. mm + 1 X 2.5 sq. mm earth wire sizes of FRLS PVC insulated copper conductor, single core cable in surface / recessed medium class PVC conduit as required

Wiring for circuit/ submain wiring along with earth wire with the 4 X 6 sq. mm + 2 X 6 sq. mm earth wire sizes of FRLS PVC insulated copper conductor, single core cable in surface / recessed medium class PVC conduit as required

Wiring for circuit/ submain wiring along with earth wire with the 4 X 10 sq. mm + 2 X 6 sq. mm earth wire sizes of FRLS PVC insulated copper conductor, single core cable in surface / recessed medium class PVC conduit as required

Wiring for circuit/ submain wiring along with earth wire with the 4 X 16 sq. mm + 2 X 6 sq. mm earth wire sizes of FRLS PVC insulated copper conductor, single core cable in surface / recessed medium class PVC conduit as required

Supplying and drawing 2 Pair 0.5 mm dia FRLS PVC insulated annealed copper conductor, unarmoured telephone cable in the existing surface/ recessed steel/ PVC conduit as required.

Supplying and drawing co-axial TV cable RG-6 grade, 0.7 mm solid copper conductor PE insulated, shielded with fine tinned copper braid and protected with PVC sheath in the existing surface/ recessed steel/ PVC conduit as required.

Supplying and fixing of 25 mm sizes of medium class PVC conduit along with accessories in surface/ recess including cutting the wall and making good the same in case of recessed conduit as required.

Supplying and fixing metal box of 100 mm X 100 mm X 60 mm deep sizes (nominal size) on surface or in recess with suitable size of phenolic laminated sheet cover in front including painting etc. as required.

Supplying and fixing of 15/16 amp switch modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required.

Supplying and fixing of 3 pin 5/6 amp socket outlet modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required.

Supplying and fixing of 6 pin 15/16 amp socket outlet modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required.

Supplying and fixing of Telephone socket outlet modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required.

Supplying and fixing of TV antenna socket outlet modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required.

Supplying and fixing modular blanking plate on the existing modular plate & switch box excluding modular plate as required.

Supplying and fixing of 3 module (100mmX75mm), GI box along with modular base & cover plate for modular switches in recess etc. As required.

Supplying and fixing 3 Module Modular base & cover plate on existing modular metal boxes etc. as required.

Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 3 pin 5/6 amps modular socket outlet and 5/6 amps modular switch, connection etc. as required. (For light plugs to be used in non residential buildings).

Supplying and drawn of 1 run of Cable UTP 4 pair CAT 6 LAN cable in the existing surface/recessed steel/PVC conduit as required

Wiring for group controlled (looped) light point/fan point/exhaust fan point/ call bell point ( without independent switch etc.) with 1.5 sq. mm FRLS PVC insulated copper conductor single core cable in surface/ recessed PVC conduit, and earthing the point with 1.5 sq. mm FRLS PVC insulated copper conductor single core cable etc. as required.

Supplying and fixing of 8 way , Double door way, single pole and neutral, sheet steel, MCB distribution board, 240 V, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator)

Supplying and fixing of 12 way , Double door way, single pole and neutral, sheet steel, MCB distribution board, 240 V, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator)

Supplying and fixing of way 4 (4 + 12), way, Double door horizontal type three pole and neutral, sheet steel, MCB distribution board, 415 V, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator)

Supplying and fixing of 8 way (4 + 24), way, Double door horizontal type three pole and neutral, sheet steel, MCB distribution board, 415 V, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator)

Supplying and fixing of 8 way (4 + 24), vertical type, Double door 415 V, TPN MCB distribution board of sheet steel, dust protected, duly powder painted, inclusive of 200 A tinned copper bus bar, common neutral link, earth bar, din bar for mounting MCBs (but without MCBs and incomer ) as required . (Note : Vertical type MCB TPDB is normally used where 3 phase outlets are required.)

Supplying and fixing of Single pole 5 amps to 32 amps rating, 240/415 volts, "C" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required.

Supplying and fixing of Double pole 5 amps to 32 amps rating, 240/415 volts, "C" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required.

Supplying and fixing of Triple pole 5 amps to 32 amps rating, 240/415 volts, "C" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required.

Supplying and fixing of 40 amps rating, four pole, 415 volts, isolator in the existing MCB DB complete with connections, testing and commissioning etc. as required.

Supplying and fixing of 63 amps rating, four pole, 415 volts, isolator in the existing MCB DB complete with connections, testing and commissioning etc. as required.

Supplying and fixing 40 amps rating, double pole, (single phase and neutral), 240 volts, residual current circuit breaker (RCCB), having a sensitivity current up to 300 milliamperes in the existing MCB DB complete with connections, testing and commissioning etc. as required.

Supplying and fixing 40 amps rating, four pole, (three phase and neutral), 415 volts, residual current circuit breaker (RCCB), having a sensitivity current up to 300 milliamperes in the existing MCB DB complete with connections, testing and commissioning etc. as required.

Supplying and fixing 63 amps rating, four pole, (three phase and neutral), 415 volts, residual current circuit breaker (RCCB), having a sensitivity current up to 300 milliamperes in the existing MCB DB complete with connections, testing and commissioning etc. as required.

Supplying and fixing 20 amps, 240 volts, SPN industrial type, socket outlet, with 2 pole and earth, metal enclosed plug top along with 20 amps "C" curve, SP, MCB, in sheet steel enclosure, on surface or in recess, with chained metal cover for the socket out let and complete with connections, testing and commissioning etc. as required.

Supplying and installing of 300 mm width X 50 mm depth X 1.6 mm thickness size of perforated pre-painted M.S. cable trays with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with M.S. suspenders including bolts & nuts, painting suspenders etc as required.

Supplying and installing of 450 mm width X 62.5 mm depth X 2.0 mm thickness size of perforated pre-painted M.S. cable trays with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with M.S. suspenders including bolts & nuts, painting suspenders etc as required.

Supplying and installing of 600 mm width X 62.5 mm depth X 2.0 mm thickness size of perforated pre-painted M.S. cable trays with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with M.S. suspenders including bolts & nuts, painting suspenders etc as required.

Providing and fixing of lightning conductor finial, made of 25 mm dia 300 mm long, G.I. tube, having single prong at top, with 85 mm dia 6 mm thick G.I. base plate including holes etc. complete as required.

Providing and fixing G.I. tape 20 mm X 3 mm thick on parapet or surface of wall for lightning conductor complete as required.(For horizontal run)

Providing and fixing G.I. tape 20 mm X 3 mm thick on parapet or surface of wall for lightning conductor complete as required.(For vertical run)

Providing and fixing testing joint, made of 20 mm X 3 mm thick G.I. strip, 125 mm long, with 4 nos. of G.I. bolts, nuts, chuck nuts and spring washers etc. complete as required.

Providing and laying G.I. tape 32 mm X 6 mm from earth electrode directly in ground as required.

Supplying, installation, testing and commissioning of Microwave technology based occupancy sensor having high performance, non regulating programmable type, suitable for connected load up to 10 Amp, for mounting height up to 2.6 mtr and for 5m x 20 m coverage area along with necessary fixing arrangements i/c programming at site etc. complete as required.

Supply, Installation, Testing and Commissioning of 1200 mm sweep, BEE 5 star rated, ceiling fan with Brush Less Direct Current (BLDC) Motor, class of insulation: B, 3 nos. blades, 30 cm long down rod, 2 nos. canopies, shackle kit, safety rope, copper winding, Power Factor not less than 0.9, Service Value (CMM/W) minimum 6.85, Air delivery minimum 215 CMM, 350 RPM (tolerance as per IS : 3742019), THD less than 10%, remote or electronic regulator unit for speed control and all remaining accessories including safety pin, nut bolts, washers, temperature rise=75 degree C (max.), insulation resistance more than 2 mega ohm, suitable for 230 V, 50 Hz, single phase AC Supply, earthing etc. complete as required.

Supply, fabrication installation of Structural steel work riveted, bolted or welded in built up sections, trusses and framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete. (steel tube for electrical fitting fixing and other supports) - 25x25x1.98mm Thick square tube.

Installation, Testing, Commissioning of wall bracket /ceiling fittings of all sizes and shapes containing up to two GLS/CFL/LED lamps per fitting, complete with all accessories including connections etc. as required.

Supply, testing and commissioning of 18 W LED down lighter fitting with cool day light made out of CRCA powder coated body, aluminium reflectors, polycarbonate diffuser, glare free light, suitable for recessed / surface mounting including electronic drivers, day light colour LED lamps, inter connecting wiring including accessories all inclusive.

Supply, testing and commissioning of 24 W LED down lighter fitting with cool day light, made out of CRCA powder coated body, aluminium reflectors, polycarbonate diffuser, glare free light, suitable for recessed / surface mounting including electronic drivers, day light colour LED lamps, inter connecting wiring including accessories all inclusive.

Supply, testing and commissioning of 36 W LED down lighter fitting with cool day light, made out of CRCA powder coated body, aluminium reflectors, polycarbonate diffuser, glare free light, suitable for recessed / surface mounting including electronic drivers, day light colour LED lamps, inter connecting wiring including accessories all inclusive.

Supply, erection, testing and commissioning of 150 W LED flood light fitting with cool day light suitable for surface / recessed mounting, made out of CRCA powder coated body, aluminium reflectors, polycarbonate diffuser, glare free light, including electronic drivers, day light colour LED lamps, inter connecting wiring including accessories all inclusive.

Supply, erection, testing and commissioning of 150 W LED outdoor flood light fitting with cool day light suitable for surface / recessed mounting, made out of CRCA powder coated body, aluminium reflectors, polycarbonate diffuser, glare free light, including electronic drivers, day light colour LED lamps, inter connecting wiring including suitable fabricated mounting arrangement compressing of 50 mm dia. class B, GI pipe with necessary mounting channels and angles, fasteners including necessary foundations etc., accessories all inclusive.

Supply, erection, testing and commissioning of 250 W LED Flood light fitting with cool day light suitable for surface / recessed mounting, made out CRCA powder coated body, aluminium reflectors, polycarbonate diffuser, glare free light, including electronic drivers, day light colour LED lamps, inter connecting wiring with suitable fixing clams, hooks as required including accessories all inclusive.

Supply, testing and commissioning of 10 W LED bulk head fitting with cool day light suitable for surface mounting, made out of CRCA powder coated body, aluminium reflectors, polycarbonate diffuser, Suitable for fitting including electronic drivers, day light colour LED lamps, inter connecting wiring including accessories all inclusive.

Supply, erection, testing and commissioning of 20 W LED confirming to IS 16103, IS 16104 emergency light fitting with exit sign, self-contained battery with a battery autonomy cool day light, made out of CRCA powder coated steel Enclosure IP 54, aluminium reflectors, suitable for mounting on stand including Sealed maintenance free rechargeable batteries with a battery autonomy of 3 hours, inbuilt battery charger, fuse, test switch, electronic drivers suitable to operate from 120 – 240 V AC single phase operation, day light colour LED inter connecting wiring etc., including accessories all inclusive.

Supply, testing and commissioning of 10 W LED mirror light fitting with cool day light suitable for surface mounting, made out of CRCA powder coated body, aluminium reflectors, polycarbonate diffuser, including electronic drivers, day light colour LED lamps, inter connecting wiring including accessories all inclusive.

Supply, erection, testing and commissioning of 10 W LED entry / exit light fitting with self contained battery with a battery autonomy of 30 minutes with cool day light, made out of CRCA powder coated body, aluminium reflectors, polycarbonate diffuser, glare free light, suitable for recessed / surface mounting including Sealed maintenance free rechargeable batteries with a battery autonomy of 30 minutes, inbuilt battery charger, fuse, test switch, electronic drivers, day light colour LED inter connecting wiring etc., including accessories all inclusive.

Supply, testing and commissioning of 18/20 W LED tube light fitting with cool day light made out of CRCA powder coated body, aluminium reflectors, polycarbonate diffuser, glare free light, suitable for recessed / surface mounting including electronic drivers, day light colour LED lamps, inter connecting wiring including accessories all inclusive.

Supply and providing 300 mm (12") sweep (light duty) 1400 RPM, AC exhaust fan complete in the provided cut-out including interconnection wire etc., as required.

Supplying and fixing of Data socket outlet modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc., as required.

Supply and fixing of 16 Amps DP key card switch for hotel / accommodation including the back box

Supply, erection, testing and commissioning of 230 V AC buzzer, 1 module suitable switch board mounting.

Supply, erection, testing and commissioning of 3 W LED type foot lamp suitable for GI module back box.

Supply, erection, testing and commissioning of 18 W LED type swimming pool fitting with IP68 rating with cool day light, made out of cast aluminium, powder coated body, reflectors, polycarbonate diffuser, glare free light, suitable for immersion in water mounting including electronic drivers, day light colour LED lamps, inter connecting wiring including accessories all inclusive.

Supply, installation testing and commissioning of Online 1.0 KVA UPS with 30 minutes SMF battery backup, with 230V, 1 phase input, 230 V single phase output including rack, accessories etc., as required.

Supply, installation testing and commissioning of Online 2.0 KVA UPS with 30 minutes SMF battery backup, with 230V, 1 phase input, 230 V single phase output including rack, accessories etc., as required.

Supply, installation testing and commissioning of Online 10.0 KVA UPS with 30 minutes SMF battery backup, with 230V, 1 phase input, 230 V single phase output including rack, accessories etc., as required.

Supply, installation testing and commissioning of 30 W LED chandeliers suitable for 230V, 1 phase input, including erection accessories

Supplying and making cable route marker with cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size ) of size 60 cm X 60 cm at the bottom and 50 cm X 50 cm at the top with a thickness of 10cm including inscription duly engraved as required.

Laying of Up to 35 sq. mm one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 kV grade of following size direct in ground including excavation, sand cushioning, protective covering and refilling the trench etc as required.

Supplying and making end termination with brass compression gland and aluminium lugs for 4 x 35 Sq.mm. AYFY, XLPE, Al, UG cable size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 kV grade as required.

Erection of metallic pole of Above 4.5 metre and up to 6.5 metre length in cement concrete 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 40 mm nominal size) foundation including excavation and refilling etc. as required.

Erection of metallic pole of Above 6.5 metre and up to 8.0 metre length in cement concrete 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 40 mm nominal size) foundation including excavation and refilling etc. as required.

Design, manufacture, supply, erection, testing and commissioning of 415 V street lighting feeder pillar box suitable for outdoor installation, made up of CRCA sheet steel of thickness not less than 2 mm with a weather proof canopy of top, double door construction, IP 55 protection, anti corrosive chemical resistant paint with 1no. 125 A TPN MCCB with 16 kA breaking capacity in the incoming and 8 nos 25 A, TPN contactor 10 nos. 25 A TPN MCCB, 24 nos, 10A SP MCB as outgoing, automatic dawn and dusk with cyclic timer control for street light outgoing and adequate plate to terminate suitable cable as incomer and suitable cable as outgoing. energy saver for automatic switching ON/OFF as per pre-sets time cycle, digital multifunctional meter with RS485 port and suitable CT etc., including concrete pedestal and associated civil works.

Supply of 3.5 core 35 sq mm XLPE insulated and PVC sheathed armoured aluminium power cable of 1.1kV grade

Supplying of 8 m Free Standing single Arm Bracket swaged pole along with base plate of size 300 x 300 x 12mm thick as per IS-875, including 4 Nos of M20X750mm high "J" type EN8 grade foundation bolts along with template and 1.50 mtr long MS Single arm bracket made up of 40NB dia. GI pipe and including Bakelite sheet with 1 No 6A SP MCB and stud type connector suitable for 4CX35Sqmm cable etc., complete

Supply and fixing of 70 W LED street light fitting with cool day light, made out of Pressure die cast aluminium body, separate compartment for LED, including electronic drivers, day light colour LED lamps, inter connecting wiring with suitable fixing clams as required including accessories all inclusive.

Design, manufacture, supply, testing and commissioning of 5m Post Top Lantern height (PTL), pole size of 100 mm dia. class - B, MS pipe with powdered coated colour as per direction of Engineers - In Charge, with inbuilt junction box, 3 R x 2.50 sq.mm FRLS insulated copper conductor with end termination for individual fitting , 6 Amps, SP MCB - 1 no.

Design, manufacture, supply, erection, testing and commissioning of 50W LED Post top Light including electronic drivers, day light colour LED lamps, inter connecting wiring with suitable fixing clams as required including accessories all inclusive.as required.

Supply, erection, testing and commissioning of High Mast Light system confirming to IS 875, 30 m height with the following:- High Mast Light system confirming to IS 875, 30 m height made of three sections - having thickness - bottom section - 5mm Middle section - 4mm & Top Section - 4mm suitable for wind speed of 180 km/h, with Hot dip galvanized complete with all accessories including head frame, pulley assembly, 3 point suspension system with 6 mm 316 Grade S.S Hoisting Wire Ropes of 7/19 construction, double drum winch, Galvanized Movable Lantern carriage arrangement, Flexible Multicore cable, Trailing Cable -5 Core X 2.5Sq. mm 1 per mast, Foundation Bolts & Nuts, Anchor Plate & Template, Lightning finial, Double Dome Aviation light (L E D type), Power Tool. ( Integral ) suitable for connecting up to 12 nos. of 350 Watts LED flood light fittings, connecting cable with accessories 16 Nos. 250 Watts LED Flood light fitting with cool day light of 5700 Kelvin +/- 100K CCT, CRI of 70 +/- 5 with System Efficacy of more than 100 Lumens Per Watt +/- 5 Lumens suitable to be operate on 240V AC 50 Hz, Operating Voltage Range of 120 to 270 Volts, P.F. greater than 0.95, THD Less than 10% with Mains Current of 1.10 Amp with Approx. Weight of 8.10 Kg, Elegantly designed highly efficient PDC aluminium housing in powder coated finish. Heat resistant toughened glass, Fins are provided on housing for better heat dissipation including separate electronic drivers, Surge Arrestor of 1 No. 10 kV, 440V, Cradle having 2Nos. 14x25mm slot & 1No. Ø20mm hole provided for mounting. And inter connecting wiring with suitable fixing clamps as required including accessories all inclusive. IP 66 Protection. Lighting Fixture similar to Crompton Cat Ref.: CFS-506-250-57-60D-SL-GL-NSG Control panel /Feeder Pillar suitable circuit for the operation of the high mast including integral power tool operation, adequate size of interconnecting cable, power and control cables, termination etc., earthing , and safety equipment's., Design, supply, erection of suitable foundation for the high mast considering the site soil condition etc., all inclusive. Including all type of civil works.

Supplying, installing by suspension on ceiling, testing and commissioning of 2500 A 50kA SC for 1 sec capacity Sandwich Type Bus Trunking for use on 3 phase 4 wire 415 volts, 50 Hz A.C. supply with metal clad enclosure made of 1.6mm thick steel sheet duly powder coated in convenient section complete with 4 Nos aluminium bus bars, necessary joints, elbow joints & expansion joints and bends, fire barrier at each floor, provision of tapping at every metre, adopter box and copper flexible for joints, continuous earthing with 2 Nos aluminium strip of suitable size( one on each side) including G.I clamping brackets, suspenders, angle iron bracket, steel fasteners, connecting to earthing system etc. as required.

Supplying and installing of 300 mm width X 50 mm depth X 1.6 mm thickness size of perforated pre-painted M.S. cable trays with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with M.S. suspenders including bolts & nuts, painting suspenders etc as required.

Supplying and installing of 450 mm width X 62.5 mm depth X 2.0 mm thickness size of perforated pre-painted M.S. cable trays with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with M.S. suspenders including bolts & nuts, painting suspenders etc as required.

Supplying and installing of 600 mm width X 62.5 mm depth X 2.0 mm thickness size of perforated pre-painted M.S. cable trays with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with M.S. suspenders including bolts & nuts, painting suspenders etc as required.

Supplying and installing of 900 mm width X 62.5 mm depth X 2.0 mm thickness size of perforated pre-painted M.S. cable trays with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with M.S. suspenders including bolts & nuts, painting suspenders etc as required.

Supplying and installing of 300 mm width X 50 mm depth X 1.6 mm thickness size of perforated pre-painted M.S. cable trays bends with perforation not more than 17.5%,, joined with connectors, suspended from the ceiling with M.S. suspenders including bolts & nuts, painting suspenders etc as required.

Supplying and installing of 450 mm width X 62.5 mm depth X 2.0 mm thickness size of perforated pre-painted M.S. cable trays bends with perforation not more than 17.5%,, joined with connectors, suspended from the ceiling with M.S. suspenders including bolts & nuts, painting suspenders etc as required.

Supplying and installing of 600 mm width X 62.5 mm depth X 2.0 mm thickness size of perforated pre-painted M.S. cable trays bends with perforation not more than 17.5%,, joined with connectors, suspended from the ceiling with M.S. suspenders including bolts & nuts, painting suspenders etc as required.

Supplying and installing 900 mm width X 62.5 mm depth X 2.0 mm thickness size of perforated pre-painted M.S. cable trays bends with perforation not more than 17.5%,, joined with connectors, suspended from the ceiling with M.S. suspenders including bolts & nuts, painting suspenders etc as required.

Earthing with G.I. earth pipe 4.5 metre long, 40 mm dia including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe etc. with charcoal/ coke and salt as required

Earthing with copper earth plate 600 mm X 600 mm X 3 mm thick including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe of 2.7 metre long etc. with charcoal/ coke and salt as required.

Supplying and laying 25 mm X 5 mm copper strip at 0.50 metre below ground as strip earth electrode, including connection/ terminating with nut, bolt, spring, washer etc. as required. (Jointing shall be done by overlapping and with 2 sets of brass nut bolt & spring washer spaced at 50mm)

Providing and laying earth connection from earth electrode with 4.00 mm dia copper wire in 15mm dia G.I. pipe from earth electrode including connection with copper thimble excavation and re-filling as required.

Providing and fixing 25 mm X 5 mm G.I. strip on surface or in recess for connections etc. as required.

Providing and fixing 6 SWG dia G.I. wire on surface or in recess for loop earthing along with existing surface/ recessed conduit/ submain wiring/ cable as required.

Providing and fixing earth bus of 50 mm X 5 mm copper strip on surface for connections etc. as required.

Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 33 kV grade of Above 120 sq. mm and up to 400 sq. mm size direct in ground including excavation, sand cushioning, protective covering and refilling the trench etc as required.

Supplying and making end termination with brass compression gland and aluminium lugs for 3½ x 25 Sq.mm. AYFY, XLPE, Al, UG cable size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 kV grade as required.

Supplying and making end termination with brass compression gland and aluminium lugs for 3½ x 35 Sq.mm. AYFY, XLPE, Al, UG cable size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 kV grade as required.

Supplying and making end termination with brass compression gland and aluminium lugs for 3½ x 70 Sq.mm. AYFY, XLPE, Al, UG cable size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 kV grade as required.

Supplying and making end termination with brass compression gland and aluminium lugs for 3½ x 95 Sq.mm. AYFY, XLPE, Al, UG cable size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 kV grade as required.

Supplying and making end termination with brass compression gland and aluminium lugs for 3½ x 120 Sq.mm. AYFY, XLPE, Al, UG cable size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 kV grade as required.

Supplying and making end termination with brass compression gland and aluminium lugs for 3½ x 185 Sq.mm. AYFY, XLPE, Al, UG cable size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 kV grade as required.

Supplying and making end termination with brass compression gland and aluminium lugs for 3½ x 240 Sq.mm. AYFY, XLPE, Al, UG cable size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 kV grade as required.

Supplying and making end termination with brass compression gland and aluminium lugs for 3½ x 300 Sq.mm. AYFY, XLPE, Al, UG cable size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 kV grade as required.

Supplying and making end termination with brass compression gland and aluminium lugs for 3½ x 400 Sq.mm. AYFY, XLPE, Al, UG cable size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 kV grade as required.

Supplying and making end termination with brass compression gland and aluminium lugs for 4 x 10 Sq.mm. AYFY, XLPE, Al, UG cable size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 kV grade as required.

Supplying and making end termination with brass compression gland and aluminium lugs for 4 x 16 Sq.mm. AYFY, XLPE, Al, UG cable size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 kV grade as required.

Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 kV grade of Upton 35 sq. mm size direct in ground including excavation, sand cushioning, protective covering and refilling the trench etc as required

Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 kV grade of Above 35 sq. mm and up to 95 sq. mm size direct in ground including excavation, sand cushioning, protective covering and refilling the trench etc as required

Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 kV grade of following size direct in ground including excavation, sand cushioning, protective covering and refilling the trench etc as required Above 95 sq. mm and up to 185 sq. mm

Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 kV grade of following size direct in ground including excavation, sand cushioning, protective covering and refilling the trench etc as required Above 185 sq. mm and up to 400 sq. mm

Laying and fixing of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 kV grade of Upton 35 sq. mm (clamped with 1mm thick saddle) size on wall surface as required

Laying and fixing of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 kV grade of Above 35 sq. mm and up to 95 sq. mm (clamped with 25x3mm MS flat clamp) size on wall surface as required

Laying and fixing of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 kV grade of Above 95 sq. mm and up to 185 sq. mm (clamped with 25/40x3mm MS flat clamp) size on wall surface as required

Laying and fixing of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 kV grade of Above 185 sq. mm and up to 400 sq. mm (clamped with 40x3mm MS flat clamp) size on wall surface as required

Laying and fixing of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 kV grade of Upton 35 sq. mm (clamped with 1mm thick saddle) size on cable tray as required.

Laying and fixing of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 kV grade of Above 35 sq. mm and up to 95 sq. mm (clamped with 25x3mm MS flat clamp) size on cable tray as required

Laying and fixing of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 kV grade of Above 95 sq. mm and up to 185 sq. mm (clamped with 25/40x3mm MS flat clamp) size on cable tray as required.

Laying and fixing of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 kV grade of Above 185 sq. mm and up to 400 sq. mm (clamped with 40x3mm MS flat clamp) size on cable tray as required.

Laying of one number XLPE power cable of 33 kV grade of Above 120 sq. mm and up to 400 sq. mm size direct in ground including excavation, sand cushioning, protective covering and refilling the trench etc as required.

Supplying and making indoor cable end termination with heat shrinkable jointing kit complete with all accessories including lugs suitable for 240 sq. mm size of 3 core, XLPE aluminium conductor cable of 33 kV grade as required.

Supplying and making outdoor cable end termination with heat shrinkable jointing kit complete with all accessories including lugs suitable for 300 sq. mm size of 3 core, XLPE aluminium conductor cable of 11 kV grade as required.

Supplying and fixing cable route marker with 10 cm X 10 cm X 5 mm thick G.I. plate with inscription there on, bolted welded to 35 mm X 35 mm X 6 mm angle iron, 60 cm long and fixing the same in ground as required.

33 kV HT Indoor Panel Design, Engineering, Manufacture, Assembly, Inspection and Testing before supply, Packing and delivery at site, erection, installation, testing & commissioning of 33 kV HT switchgear with all accessories and suitable for installation in three phase, three wire,33 kV, 50 Hz, A.C. distribution network. complete with all accessories erected in the provided foundation complete as per specification and as directed by engineer in charge at site. The VCB panel shall be complying to APDCL specification. Indoor type, 33 kV VCB panel with 1 No. Vacuum Circuit Breaker in tee OFF the Vacuum Circuit Breaker (VCB) feeder shall Comprise of 1 No. 33 kV, 630A, 18.0 kA, for 3 sec, manual operated VCB 1 No. Common Items & Accessories for each RMU1 set Operating Handle the panel shall be suitable for terminating 1 R of 3C x 300 Sq.mm XLPE 33 kV (E) cable.

Outdoor transformers Supply, erection, testing and commissioning of 33 / 0.433 kV, 1250 kVA, copper wound, outdoor distribution transformer, ONAN, DYn11, with On load tap changer range from+5% to -15% in steps of 1.25% with 16 steps / 17 positions, RTCC panel etc., complete with first oil filled, with suitable cable box for HT side termination and Bus duct in LT side termination complying to IS 1180, including transportation, unloading at site, in the constructed foundation of adequate depth for transformer plinth of height 450 mm above FGL, mounting channelling etc., all inclusive. Specification should meet IS 1180 transformer losses level -3.

Supply, erection, testing, commissioning of 625 KVA, 415 V, 3 phase, 50 Hz, DG Set suitable for synchronisation with diesel engine at 1500 RPM coupled with alternator rated at 625 KVA, 415 V, 0.8 PF mounted on a channel Iron base frame, fuel tank of adequate capacity, starting batteries with leads, AMF panel, hospital type silencer, with acoustic enclosure , control panel, inter connecting control cable, cable end termination, including lubrication system, cooling system, all inclusive. DG set should comply with central pollution control board (CPCB) norms as per the latest environment (protection) rules.

Sub switch board - Type 1 Design, supply, assembly, wiring, supply, installation, testing and commissioning of CPRI/ERDA tested floor standing, single front, fully compartmentalized, double ended, IEC 60439 compliant, 14 G CRCA sheet steel fabricated IP 42 protected complete, AMF relay with necessary control wiring arrangement as per specification, comprising of the following major switchgear/ devices / components and form-IIIB form of construction. Metering Digital multi-function meter with necessary CTs (A, V, kW kWh, kVA, RkVA, PF), with RS 485 communication Indications Cluster type LED indication lamps for 3 phases, ON, OFF, TRIP. Busbar 400A, 36 kA/1 sec., 415 Volts, TPN (100 % neutral), 50 Hz Aluminium bus bars Incomer - 1 400 A, TPN MCCB 36 kA, - 1 Nos. with Microprocessor based O/C, S/C & E/F releases with electrical interlock with EDG incomer Outgoing: 125 A, TPN MCCB 25 kA, - 6 Nos. 63 A, TPN MCCB 25 kA, - 10 Nos. 32 A, TPN MCCB 25 kA, - 2 Nos.

Sub switch board - Type 2 Design, supply, assembly, wiring, supply, installation, testing and commissioning of CPRI/ERDA tested floor standing, single front, fully compartmentalized, double ended, IEC 60439 compliant, 14 G CRCA sheet steel fabricated IP 42 protected complete as per specification, comprising of the following major switchgear/ devices / components and form-IIIB form of construction. Metering Digital multi-function meter with necessary CTs (A, V, kW kWh, kVA, RkVA, PF), with RS 485 communication Indications Cluster type LED indication lamps for 3 phases, ON, OFF, TRIP, Busbar 250A, 36 kA/1 sec., 415 Volts, TPN (100 % neutral), 50 Hz Aluminium bus bars Incomer 250 A, TPN MCCB 36 kA, - 1 Nos. with Microprocessor based O/C, S/C & E/F releases Outgoing: 63 A, TPN MCCB 25 kA, - 8 Nos. 32 A, TPN MCCB 25 kA, - 2 Nos.

Utility Panel Design, supply, assembly, wiring, supply, installation, testing and commissioning of CPRI/ERDA tested floor standing, single front, fully compartmentalized, double ended, IEC 60439 compliant, 14 G CRCA sheet steel fabricated IP 42 protected complete as per specification, comprising of the following major switchgear/ devices / components and form-IIIB form of construction. Metering Digital multi-function meter with necessary CTs (A, V, kW kWh, kVA, RkVA, PF), with RS 485 communication Indications Cluster type LED indication lamps for 3 phases, ON, OFF, TRIP, local, remote in each of the two-incomer ACB compartments. Busbar 250A, 36 kA/1 sec., 415 Volts, TPN (100 % neutral), 50 Hz Aluminium bus bars Incomer 250A, TPN MCCB 36 kA, - 1 Nos. with Microprocessor based O/C, S/C & E/F releases with electrical interlock with EDG incomer Outgoing: 125 A, TPN MCCB 25 kA, - 4 Nos. 63 A, TPN MCCB 25 kA, - 6Nos. 32 A, TPN MCCB 50 kA, - 4 Nos.

Supply of one number XLPE insulated and PVC sheathed armoured aluminium power cable of 1.1 kV grade of the sizes 4Cx10 sqmm XLPE Al. Ar. cable

Supply of one number XLPE insulated and PVC sheathed armoured aluminium power cable of 1.1 kV grade of the sizes 4Cx16 sqmm XLPE Al. Ar. cable

Supply of one number XLPE insulated and PVC sheathed armoured aluminium power cable of 1.1 kV grade of the sizes 3.5Cx25 sqmm XLPE Al. Ar. Cable

Supply of one number XLPE insulated and PVC sheathed armoured aluminium power cable of 1.1 kV grade of the sizes 3.5Cx35 sqmm XLPE Al. Ar. Cable

Supply of one number XLPE insulated and PVC sheathed armoured aluminium power cable of 1.1 kV grade of the sizes 3.5Cx70 sqmm XLPE Al. Ar. Cable

Supply of one number XLPE insulated and PVC sheathed armoured aluminium power cable of 1.1 kV grade of the sizes 3.5Cx95 sqmm XLPE Al. Ar. Cable

Supply of one number XLPE insulated and PVC sheathed armoured aluminium power cable of 1.1 kV grade of the sizes 3.5Cx120 sqmm XLPE Al. Ar. Cable

Supply of one number XLPE insulated and PVC sheathed armoured aluminium power cable of 1.1 kV grade of the sizes 3.5Cx185sqmm XLPE Al. Ar. Cable

Supply of one number XLPE insulated and PVC sheathed armoured aluminium power cable of 1.1 kV grade of the sizes 3.5Cx240 sqmm XLPE Al. Ar. Cable

Supply of one number XLPE insulated and PVC sheathed armoured aluminium power cable of 1.1 kV grade of the sizes 3.5Cx300 sqmm XLPE Al. Ar. Cable

Supply of one number XLPE insulated and PVC sheathed armoured aluminium power cable of 1.1 kV grade of the sizes 3.5Cx400 sqmm XLPE Al. Ar. Cable

Supply of one number PVC insulated and PVC sheathed armoured aluminium power cable of 33 kV grade of the sizes 33kV, 3 core 300 sqmm XLPE Al. Ar. cable

Supplying and laying 50 mm X 6 mm copper strip at 0.50 metre below ground as strip earth electrode, including connection/ terminating with G.I. nut, bolt, spring, washer etc. as required.(Jointing shall be done by overlapping and with 2 sets of G.I. nut bolt & spring washer spaced at 50mm)

Supplying installation, testing and commissioning of 10 passenger 680 Kg.) Model : GEN 2 COMFORT with stainless steel (machine room less) lifts having contract speed of 1 MPS serving different floors in the lift shaft as per detailed specification enclosed and as under: 1. No. of Elevators 1 No. 2. Type GEN 2 COMFORT MRL 3. Capacity Passenger - 13 Persons - 884 Kg 4. Speed 1.0 Metre/Sec (approx.) 5. Control ACVVF - OTIS Variable Frequency with speed encoder. 6. Operation Simplex Full Collective Control. 7. Controller Microprocessor based modular control system ( Location door column at top floor 8. Communication Loop type serial communication 9. Travel GF to first floor about 10.0 Metres. 10. Stop & Opening 2 Stops 2 Levels 2 Openings (All opening on the same side 11. 10. Power Supply 400 V ± 10% variation ,three-phase 50 Hz ± 5% variation 12. Machine Gearless with permanent magnet motor located in the shaft at top. 13. Rope Flat poly urethane - coated belts 14. Cab finish SS car, door, ceiling and handrails in car and vinyl flooring. 15. Cab ventilation Pressure fan 16. Cab Size 1600 mm Wide x 1350 mm Deep approx. 17. Shaft size required 2300mmx 1700mm(HXW) 18. Entrance type Centre opening. 19. Fire rating One hour fire rated. 20. Entrance opening 900mmx 2000mm 21.Over head 4000mm 22. Pit depth 1300mm 23. Entrance protection system High Performance contact free infra red curtain - 2 dimensional 24. Door operation Power operated automatic sliding doors. 25. Door operator DC door operator system. 26. Human interface device (H ) Hall button with micro stroke push buttons combined with 16 segment digital LED display position indicator. Full height car operating panel with micro stroke call push buttons (located on side panel)Door open and door close button on the car operating panel.2 way Intercommunication System Dot matrix position indicator display integrated with the car operating panel. Battery Operated Emergency Alarm and Light. Fireman's switch at main lobby Automatic rescue device.

Supplying, Testing and Commissioning of 2.0 MP Fixed Lens Dome Camera including erection hardware and accessories etc., as required.] Make: Bosch/ Honeywell / Equivalent

Supplying, Testing and Commissioning of 4.0 MP Motorised Lens Bullet Camera including erection hardware and accessories etc., as required Make: Bosch/Honeywell/Equivalent

Supplying, Testing and Commissioning of 4.0 MP PTZ Camera including erection hardware and accessories etc., as required Make: Bosch /Honeywell /Equivalent

Professional Network Video Recorder 32 Channel including erection hardware and accessories etc., as required Make: Bosch/Honeywell/Vivotek

Supplying, Testing and Commissioning of Hard Disk 8 TB including erection hardware and accessories etc., as required Brand: Seagate/ Western Digital 3-4 Month Recording Capacity

Supplying, Testing and Commissioning of GI Pole of 3 metres with required design including erection hardware and accessories etc., as required Make: Nezone/ Tata

Supplying, Testing and Commissioning of 8-Port Gigabit PoE+ Ethernet including erection hardware and accessories etc., as required

Supplying, Testing and Commissioning of Cat 6 Cable including erection hardware and accessories etc., as required

Supplying, Testing and Commissioning of 6 Core Fiber Cable including erection hardware and accessories etc., as required

Supplying, Testing and Commissioning of SFP Module including erection hardware and accessories etc., as required

Supplying, Testing and Commissioning of Pigtail including erection hardware and accessories etc., as required

Supplying, Testing and Commissioning of 12U Rack Loaded Rack including erection hardware and accessories etc., as required

Supplying, Testing and Commissioning of Outdoor Rack 6U Rack including all fixing accessories and support as required

Supplying, Installing, Testing and Commissioning of LED panel 55inch including all fixing accessories and support as required

Laying and installation of CAT 6 and OFC cable including erection accessories.

Installation of CCTV camera with fixed lenses & Bullet camera including erection accessories.

Installation of PTZ CCTV camera including erection hardware and accessories etc., as required

Installation, testing commissioning of NVR setup and configuration including erection accessories.

M/S KENGE CONSTRUCTION CO.