Construction of Jawan barracks with a capacity of 60 each ( Male ) at IRP 25th at Phyang Leh

Earth work in excavation by mechanical means (Hydraulic excavator) over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan) including getting out and disposal of excavated earth lead upto 50 m and lift upto 1.5 m, as directed by Engineer-in-charge. All kinds of soil

Ordinary or hard rock

Extra for every additional lift of 1.5 m or part thereof in excavation / banking excavated or stacked materials. All kinds of soil

Ordinary or hard rock

Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift upto 1.5 m.

Carriage of excated earth by mechinacal transport upto 5 kms ( including loading & unloading .

Dumping stone incuding cost of stones . In Horizontal on level.

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level :1:4:8 (1 Cement : 4 coarse sand (zone-III) derived from natural sources : 8 graded stone aggregate 40 mm nominal size derived from natural sources)

Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement - All work up to plinth level : 1:1.5:3 (1 cement : 1.5 coarse sand (zone-III) derived from natural sources : 3 graded stone aggregate 20 mm nominal size derived from natural sources)

Reinforced cement concrete work in beams, suspended floors, roofs having slope up to 15° landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases above plinth level up to floor five level, excluding the cost of centering, shuttering, finishing and reinforcement, with 1:1.5:3 (1 cement : 1.5 coarse sand(zone-III) : 3 graded stone aggregate 20 mm nominal size).

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level :1:3:6 (1 Cement : 3 coarse sand (zone-III) derived from natural sources : 6 graded stone aggregate 20 mm nominal size derived from natural sources)

Random rubble masonry with hard stone in foundation and plinth including levelling up with cement concrete 1:6:12 (1 cement : 6 coarse sand : 12 graded stone aggregate 20 mm nominal size) upto plinth level with : Cement mortar 1:6 (1 cement : 6 coarse sand)

Centering and shuttering including strutting, propping etc. and removal of form work for : Foundations, footings, bases for columns

Retaining walls, return walls, walls (any thickness) including attached pilasters, buttresses, plinth and string courses fillets, kerbs and steps etc.

Suspended floors, roofs, landings, balconies and access platform

Lintels, beams, plinth beams, girders, bressumers and cantilevers

Columns, Pillars, Piers, Abutments, Posts and Struts

Edges of slabs and breaks in floors and walls Under 20 cm wide

Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level.Thermo-Mechanically Treated bars of grade Fe-500D or more.

Supplying and filling in plinth with sand under floors, including watering, ramming, consolidating and dressing complete.

Providing & fixing upto floor five level compressed stabilized earth blocks (CEB) made an appropriate mix of dry inorganic subsoil, non-expansive clay, sand, and aggregate with 5% cement as stabilizer, in mud mortar, including cost of materials complete.

Providing & fixing upto floor five level precast cement concrete solid blocks including hoisting and setting in position in cement mortar 1:3 (1cement:3 coarse sand), cost of required centring, shuttering and curing complete1:3:6 (1 cement : 3 coarse sand : 6 graded crushed stone aggregate 20 mm nominal size)

Providing and Fixing factory made uPVC door frame, made of uPVC exturded sections, of size 65 mm xplastic brackets and stainless steel screws, reinforcing hinge side vertical of the frames with PVC profileof Size 28 mm x 30 mm having wall thickness 2 mm (±0.2 mm), including providing & fixing 3 nos of 126mm long stainless steel hinges to the frame, fixing the frame with jamb with required number & size ofanchor dash fastners, all complete as per manufacturer's specification and direction of Engineer-in-charge.

Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position with hold fast lugs or with dash fasteners of required dia & length (hold fast lugs or dash fastener shall be paid for separately).Second class Kail wood

Providing and fixing ISI marked flush door shutters conforming to IS : 2202 (Part I) decorative type, core of block board construction with frame of 1st class hard wood and well matched teak 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters.35 mm thick including ISI marked Stainless Steel butt hinges with necessary screws

Providing and fixing factory made uPVC white colour casement/casement cum fixed glazed windowscomprising of uPVC multi-chambered frame, sash and mullion (where ever required) extruded profilesduly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process ofrequired length (shape & size according to uPVC profile), uPVC extruded glazing beads of appropriatedimension, EPDM gasket, stainless steel (SS 304 grade) friction hinges, zinc alloy (white powder coated)casement handles, G.I fasteners 100 x 8 mm size for fixing frame to finished wall, plastic packers, plasticcaps and necessary stainless steel screws etc. Profile of frame & sash shall be mitred cut and fusionwelded at all corners, mullion (if required) shall be also fusion welded including drilling of holes for fixinghardware's and drainage of water etc. After fixing frame the gap between frame and adjacent finished wallshall be filled with weather proof silicon sealant over backer rod of required size and of approved quality,all complete as per approved drawing & direction of Engineer-in-Charge. (Single / double glass panes andsilicon sealant shall be paid separately). Variation in profile dimension in higher side shall be acceptedbut no extra payment on this account shall be made.For uPVC frame, sash and mullion extruded profiles minus 5% tolerance in dimension i.e. in depth& width of profile shall be acceptable.uPVC profile should be tested by BSI(UK) & SKZ(Germany) @25000 weathering hoursCasement window double panels with S.S. friction hinges (350 x 19 x 1.9 mm) made of (big series)frame 67 x 60 mm & sash / mullion 67 x 80 mm both having wall thickness of 2.3 ± 0.2 mm and single glazing bead/ double glazing bead of appropriate dimension. (Area of window above 1.50 sqm).

Providing, assembling and supplying vision glass panels (IGUs) comprising of hermetically-sealed 6-12-7 mm insulated glass (double glazed) vision panel units of size and shape as required and specified,comprising of an outer heat strengthened float glass 6mm thick, of approved colour and shade withreflective soft coating on surface # 2 of approved colour and shade, an inner Heat strengthned clear floatglass 6mm thick, spacer tube 12mm wide, dessicants, including primary seal and secondary seal(structural silicone sealant) etc. all complete for the required performances, as per the Architecturaldrawings, as per the approved shop drawings, as specified and as directed by the Engineer-in- Charge.The IGUs shall be assembled in the factory/ workshop of the glass processor. Sqm 4389.28 (Payment for fixing of IGU Panels in the curtain glazing is included in cost of item No.25.2)For payment, only the actual area of glass on face # 1 of the glass panels (excluding the areas of thegrooves and weather silicone sealant) provided and fixed in position, shall be measured in sqm. (i) Coloured tinted float glass 6mm thick substrate with reflective soft coating on face # 2, + 12mmAirgap + 6mm Heat Strengthened clear Glass of approved make having properties as visible Lighttransmittance (VLT) of 25 to 35 %, Light reflection internal 10 to 15%, light reflection external 10 to 20 %,shading coefficient (0.25- 0.28) and U value of 3.0 to 3.3 W/m2 degree K etc. The properties ofperformance glass shall be decided by technical sanctioning authority as per the site requirement.

Providing and fixing 50 mm thick extruded polystyrene rigid insulation board of required size betweencavity wall, complying with ISO 4898:2008 & ASTM C 578- 08b - type VI, having thermal conductivity of0.0289 W/m K as per ASTM C 578 (measured as per IS 3346), compressive strength of > 350 kPa listed asper ASTM D 1621, density of 34-36 kg/m3 as per ASTM D 1622, water absorptions < 1% by volume as perASTM D 2842, oxygen index of 24.1 to 28.1 listed as per ASTM D 2863, cell size 0.4 mm of dia (max) asper ASTM D 3576. Fire retardent property as per DIN 4102, Part 1 of class B2 and as per ASTM E84 classA, fixed with suitable water based adhesive and fastener, complete in all respect as per the direction of Engineer-in-Charge.

15 mm cement plaster on the rough side of single or half brick wall of mix : 1:4 (1 cement: 4 fine sand)

6 mm cement plaster of mix : 1:3 (1 cement : 3 fine sand)

12 mm cement plaster of mix :1:6 (1 cement: 6 fine sand)

Providing and applying plaster of paris putty of 2 mm thickness over plastered surface to prepare the surface even and smooth complete.

Applying priming coats with primer of approved brand and manufacture having low VOC (Volatile Organic Compound ) content.With water thinnable cement primer on wall surface having VOC content less than 50 grams/litre

Finishing walls with Deluxe Multi surface paint system for interiors and exteriorsusing Primer as permanufacturers specifications : Two or more coats applied on walls @ 1.25 ltr/10 sqm over and including one coat of Special primer applied @ 0.75 ltr /10 sqm

Finishing walls with textured exterior paint of required shade : New work (Two or more coats applied @ 3.28 ltr/10 sqm) over and including priming coat of exterior primer applied @ 2.20kg/10 sqm

Cement concrete flooring 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate) finished 40 mm thick with 20 mm nominal size stone aggregate

Providing and fixing 18 mm thick gang saw cut, mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels.Granite of any colour and shadeArea of slab over 0.50 sqm

Providing and laying water proofing treatment on roofs of slabs by applying cement slurry mixed with water proofing cement compound consisting of applying : (a) after surface preparation, first layer of slurry of cement @ 0.488 kg/sqm mixed with water proofing cement compound @ 0.253 kg/sqm. (b) laying second layer of Fibre glass cloth when the first layer is still green. Overlaps of joints of fibre cloth should not be less than 10 cm. (c) third layer of 1.5 mm thickness consisting of slurry of cement @ 1.289 kg/sqm mixed with water proofing cement compound @ 0.670 kg/sqm and coarse sand @ 1.289 kg/sqm. This will be allowed to air cure for 4 hours followed by water curing for 48 hours. The entire treatment will be taken upto 30cm on parapet wall and tucked into groove in parapet all around. (d) fourth and final layer of brick tiling with cement mortar (which will be paid for separately For the purpose of measurement the entire treated surface will be measured.

Providing and fixing stainless steel ( Grade 304) railing made of Hollow tubes, channels, plates etc.,

Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS: 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineerin- Charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade complete.

Providing and laying Vitrified tiles in floor in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS:15622, of approved brand & manufacturer, in all colours and shade, laid on 20 mm thick cement mortar 1:4 (1 cement: 4 coarse sand) jointing with grey cement slurry @3.3 kg/sqm including grouting the joints with white cement and matching pigments etc. The tiles must be cut with the zero chipping diamond cutter only . Laying of tiles will be done with the notch trowel, plier, wedge, clips of required thickness, leveling system and rubber mallet for placing the tiles gently and easily. Double charge vitrified tile polished finish of size Size 600x600 mm

Providing and laying water proofing treatment in sunken portion of WCs, bathroom etc., by applying cement slurry mixed with water proofing cement compound consisting of applying : (a) First layer of slurry of cement @ 0.488 kg/sqm mixed with water proofing cement compound @ 0.253 kg/sqm. This layer will be allowed to air cure for 4 hours (b) Second layer of slurry of cement @ 0.242 kg/sqm mixed with water proofing cement compound @ 0.126 kg/sqm. This layer will be allowed to air cure for 4 hours followed with water curing for 48 hours. The rate includes preparation of surface, treatment and sealing of all joints, corners, junctions of pipes and masonry with polymer mixed slurry.

Providing and fixing 12 mm thick pre laminated flooring of approved brand as per direction of engineer incharge complete job AC- 4 including carriage.

Providing and fixing 12mm thick commercial ply conforming to IS : 1328 BWR type in base for wall panelling

Providing and fixing 100mm pine wood plain lining tongued and grooved, including wooden plugs complete with necessary secrew and priming coat on unexposed surface. 10mm thick

French spirit polishing, Two or more coats on new works including a coat of wood filler

Painting with oil type wood preservative of approved brand and manufacture on New work (two or more coats)

Making plinth protection 50mm thick of cement concrete 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) over 75mm bed of dry brick ballast 40mm nominal size well rammed and consolidated and grouted with fine sand including finishing the top smooth and curing complete

Providing and fixing traditionally carved wood work (Shingstak) over doors and windows including all accessories as per the direction of the Engineer in-charge, complete with; Budloo Wood

Applying priming coat:With ready mixed pink or grey primer of approved brand and manufacture on wood work (hard and soft wood)

Painting with synthetic enamel paint of approved brand and manufacture to give an even shade two or more coats on wood / steel works.

Providing and fixing of bright finished brass hardware fittings 200 mm Handle ( Fancy )

250x10mm Tower bolt

Providing and fixing chromium plated brass 100 mm mortice latch and lock with 6 levers and a pair of lever handles of approved quality with necessary screws etc. complete.

Providing and fixing aluminum hanging floor door stopper, ISI marked, anodized (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade with necessary screws etc. complete : 9.103.2 Twin rubber stopper

Providing 40x5 mm flat iron hold fast 40 cm long including fixing to frame with 10 mm diameter bolts, nuts and wooden plugs and embeddings in cement concrete block 30x10x15 cm 1:3:6 mix ( 1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size).

Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS : 1285, fixed with rawl plugs and screws or with fixing clips, or with expansion hold fasteners including necessary filling up of gaps at junctions, at top, bottom and sides with required PVC/neoprene felt etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / panelling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing and panelling to be paid for separately): Anodised aluminium (anodised transparent or dyed to required shade according to IS: 1868, Minimum anodic coating of grade AC 15) Fixed Portion

Providing and fixing double glazed hermetically sealed glazing in aluminium windows, ventilators and partition etc. with 6 mm thick clear float glass both side having 12 mm air gap including providing EPDM gasket, perforated aluminium spacers, desiccants, silicon sealant (Both primary and secondary sealant) etc. as per specifications, drawings and direction of Engineer-in-charge complete.

Carriage of materials Stone agg. Below 40mm size Avg. 25K.m

Sand Avg. 20K.m

Cement Avg. 20 K.m

Steel Avg. 20 K.m

Earth work in excavation by manual means in trenches for foundations, drains, pipes, cables etc. (not exceeding 1.5 m in width) and for shafts, wells, cesspits and the like not exceeding 10 sqm on plan, including dressing of sides and ramming of bottoms lift upto 1.5 m, including getting out excavated earth and disposal of surplus excavated earth as directed

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level :1:2:4 (1 cement : 2 coarse sand (zone-III) derived from natural sources : 4 graded stone aggregate 20 mm nominal size derived from natural sources)

Random rubble masonry with hard stone laid dry in foundation, plinth & walls Laid with bond stone

Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS : 1285, fixed with rawl plugs and screws or with fixing clips, or with expansion hold fasteners including necessary filling up of gaps at junctions, at top, bottom and sides with required PVC/neoprene felt etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / panelling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing and panelling to be paid for separately): Polyester powder coated aluminium (minimum thickness of polyester powder coating 50 micron)

Providing and fixing 12mm thick prelaminated particle board flat pressed three layer or graded wood particle board conforming to IS: 12823 Grade 1 Type II in panelling fixed in aluminium doors, windows shutters and partition frames with C.P. brass / stainless steel screws etc. complete as per architectural drawings and directions of engineer-in-charge. With float glass panes of 5.50 mm thickness

Providing and fixing 12mm thick prelaminated particle board flat pressed three layer or graded wood particle board conforming to IS: 12823 Grade 1 Type II in panelling fixed in aluminium doors, windows shutters and partition frames with C.P. brass / stainless steel screws etc. complete as per architectural drawings and directions of engineer-in-charge.Prelaminated particle board with decorative lamination on both sides.

Structural steel work in built up section trusses and framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel promer all complete including 1mm thick MS sheets for sifits and eves boarding . Welded

Providing colour coated Hi- rib profile sheet roofing of approved brand & manufacture fixed with polymer coated steel screws bolts 100 mm long 8mm dia with washer & pls cap ( upon a pitch of 60 degrees ) excluding the cost of purloins, rafters and trusses ( 0.50 mm thick )

Providing and fixing 3 layer PP-R (Poly propylene Random copolymer) pipes conforming to IS: 15801, UV stabilized and anti-microbial fusion welded, having thermal stability for hot and cold water supply including all PP-R plain and brass threaded Polypropylene random fittings. This includes testing of joints complete as per direction of Engineer-incharge. Internal work Concealed fixing the pipe with clamps at 1.00 meter spacing including cutting chases and making good the 25mm OD(SDR-7.4

40mm OD (SDR-7.4 ) Roof to Down

50mm OD(SDR-7.4) Ground to roof tanks

External work including trenching, refilling etc. Main supply line. 63 mm OD (SDR-7.4)

Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) 65 mm nominal bore

Providing and fixing ball valve PPR of approved quality complete 25mm dia OD

40 mm dia

50 mm dia

Providing and placing on terrace (at all floor levels) polyethylene water storage tank ISI : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank

Providing and fixing C.P. Brass extension nipple (size 15mmx50mm) of approved make and quality as per direction of Engineer incharge.

Providing and fixing PTMT Ball cock of approved quality, colour and make complete with epoxy coated aluminium rod with L.P/H.P.H.D plastic balls.25mm nominal bore, 152mm long, weighing not less than 440gms.

Providing and fixing 15 mm nominal bore C.P. brass bib cock of approved quality conforming to IS : 8931

Providing and fixing 15 mm nominal bore C.P. brass angle valve for basin mixer and geyser points of approved make conforming to IS : 8931

Providing and fixing 15 mm nominal bore of standard back type C.P. brass close hole basin mixer pillar tap of approved quality and make, weighing not less than 1.970 kg.

P/F CP long brass single long swing type lever wall sink mixer of approved quality and make as approved by engineeh-in-charge 15mm dia

P/F CP brass Double lever wall mixer with concealed shower of approved quality and make as approved by engineeh-in-charge 15mm dia

Providing and fixing vitreous china dual purpose closet suitable for use as squatting pan or European type water closet (Anglo Indian W.C pan) with seat & lid fixed with C.P. brass hinges and rubber buffers, 10 litre low level flushing cistern with fitting and brackets, 40 mm flush bend, 20 mm over flow pipe, with specials of standard make and mosquito proof coupling of approved municipal design complete, including painting of fittings and brackets, cutting and making good the walls and floors wherever required: White vitreous china dual purpose WC pan with white solid plastic seat and lid with white vitreous china flushing cistern and C.P. flush bend.

Providing and fixing white vitreous china wash Basin with C.I brackets, single hole basin mixer, 32mm CP brass waste of standard pattern , incl. painting of fittings and brackets, cutting and making good the walls where ever required. Wash basin 550x400mm with a pair of 15mm CP brass taps

P/F white vitreous china pedestal for wash basin complete rested at back for the reception of pipe and fittings

Kitchen Sink 600x510x200mm , Incl all fitting CP waste. PVC waste pipe . making PVC connections.P/F PVC waste 32mm

P/F PVC waste 32mm

P/F 8mm dia C.P/S.S jet with flexible tube up to 1mter long with S.S triangular plate to European type W.C of approved quality and make.

P/F 600x450mm bevelled edge mirror of superior glass of approved quality complete with 6mm thick hard board ground glass to wooden cleats with C.P brass screws and washers complete.

P/F 600x120x5mm glass shelf with edges off. Supported on anodised angle frame with CP brass brackets and guard rail complete fixed with 40mm screws, rawl plugs etc.

P/F toilet paper holder (CP)

P/F in position PVC P or S traps

P/F in position PVC floor trapsa 100mm dia

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings, this included jointing of pipes & fittings with one step CPVC solvent cement, trenching, refilling & testing of joints complete as per direction of Engineer in Charge. (External work). 150mm dia

100mm dia

65mm dia

50mm dia

PVC Cowell 50mm dia

P/F PVC stay and clamps for PVC pipesa) 100mm

P/F bend of required degree with door, inspection rubber washer 3mm thick, bolts and nuts complete PVC S&S pipes 100mm

P/F plain bendsa) 100mm

Providing and filling the joints with spun yarn, cement slurry and cement mortar 1:2 100mm

P/F Tee-junction of required degree with access door, inserted rubber washer 3mm thick, bolts and nuts complete.100x100x100 PVC 1mm 100mm

P/F PVC Reducer 100-50mm dia

Providing and fixing liquid PTMT soap container 109mm wide 125mm high and of approved quality weighing not less than 105 grms

P/F PTMT towel rails with brackets fixed to wooden cleats with CP brass with concealed fittings arrangement of approved quality (600mm long total length 645mm ,`78mm wide and effective hight 88mm weighing not less than 190gms

Providing and fixing 100 mm sand cast iron grating for gully trap.

Providing and fixing uplasticized PVC connection pipe with brass unions. 45 cm long

Constructing brick masonry chamber for underground C.I. inspection chamber and bend with common burnt clay (non modular) bricks of class designation 7.5 in cement mortar 1:4 ( 1 cement : 4 coarse sand) C.I. cover with frame (light duty) 455x610 mm internal dimensions, total weight of cover with frame to be not less than 38 kg (weight of cover 23kg and weight of frame 15 kg ) R.C.C. top slab with 1:1 ½ : 3 mix ( 1cement : 1 ½ coarse sand : 3 graded stone aggregate 20 mm nominalsize),foundation concrete 1:5:10 (1 cement: 5 fine sand: 10 graded stone aggregate 40mm nominal size), inside plastering 12 mm thick with cement mortar 1:3 ( 1 cement : 3 coarse sand) finished smooth with a floating coat of neat cement on walls and bed concrete etc. complete as per standard design : 19.30.1 Inside dimensions 455x610 mm and 45 cm deep for single pipe line-

P/F master trap

Providing and fixing 5 H.P C.G Motar, including all fitting 2no ball value, non return value vertical/ horizontal, shelter, base, electric pannel switch board with DP MCB 20amph

Providing and fixing of material for the insulation of water storage tank of with nitrile sheet taping with cello tape, rockwool 6 inch per side, wire mesh, polythene, alluminium sheet 26 gage cladding with dia of, complete job 19mm thick nitrile sheet.

Providing and Fixing of heat tape 33 watt on PPR Pipes made of denforced or Chromelox or equalent make as per approved by engineer incharge complete job.

Providing and fixing Urinal basin with all fittings and fixtures complete including cutting and making good the walls and floors wherever required : One urinal basin with 5 litre white P.V.C. automatic flushing cistern.

Providing and fixing of material for the insulation of pipe with netrile tube, tapping with cello tape for inner walls fitting complete job including carriage 19mm thick, 50mm dia (OD) (PPR 25mm)

Providing and fixing of material for the insulation of Pipe with nitrile tube taping with cello tape, rockwool 6 inch per side, wire mesh, polythene, alluminium sheet 26 gage cladding with dia of, complete job 19mm thick, 50mm dia (OD)(PPR 40MM)

19mm thick, 50mm dia (OD)(PPR 50MM)

Providing and fixing Gysers (Venus, Recold) 50 Litre for Wash Room

25 Litre for Kitchen

Wiring for light point/fan point/exhaust point /call point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit, with modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable etc. as required.Group B Light Point

Fan Point

Exhaust point

Supplying and fixing of following modular switch socket on the existing modular plate and switch box including connections but excluding modular plate etc as required .5/6 A Switch

3 pin 5/6 socket outlet.

Wiring for Duplex receptacle socket outlets points socket points including Suitable GI box wiith modular plate and cover in front or in recess including providing and fixing of 2 No x 3pin 5/6 A Dubplex modular socket outlet and 5/6 Amodular switch , connections as required 2.5 sq. mm. PVC insulated cable FRLS with copper multi strandconductor ISI marked in surface PVC conduit 2.5 sq. mm. PVC insulated FRLS copper earth continuity conductor of green colour inside conduit, screwless connector for joints as per specification.(Two No such Combo Duplex Socket outlets shall be looped to the one single Power circuit to PDB.(Note:Crabtree/Legrand/Schinder/Anchor Roma Plus/Honeywell make )

Supplying and fixing of Tripliex Computer socket points including Suitable GI box wiith modular plate and cover in front or in recess including providing and fixing of 3 No x 3pin 5/6 A Triplex modular socket outlet and 5/6 Amodular switch , connections as required 2.5 sq. mm. PVC insulated cable FRLS with copper multi strandconductor ISI marked in surface PVC conduit 2.5 sq. mm. PVC insulated FRLS copper earth continuity conductor of green colour inside conduit, screwless connector for joints as per specification.(Two No such Combo Duplex Socket outlets shall be looped to the one single Power circuit to PDB.(Note:Crabtree/Legrand/Schinder/Anchor Roma Plus/Honeywell make )

Point wiring (including metallic switch box & sheet) for 6 pin 5/6 A & 15/16 A modular socket outlet and1 5/16 A modular switch, point with 4sq. mm. PVC insulated cable FRLS with copper multi strandconductor ISI marked in surface rigid steel conduit ISI marked of suitable size including painting etc. with 20/16 Amp. F.T. switch & socket/S.S. combined 20/16/6 amp. of ISI marked and 4sq. mm. PVC insulated FRLS copper earth continuity conductor of green colour inside conduit, screwless connector for joints as per specification.(Two Power Socket outlets shall be looped to the one single Power circuit to PDB.However Geysers sockets outlets shall be connected per one circuit to the nearest Power Distribution Board).

Supplying and drawing single core PVC insulated cable FRLS with copper multi strand conductor ISI marked in existing rigid PVC casing and capping/conduit in surface or concealed as per specification.1Rx2C X 2.5 sq. mm + 1 X 2.5 sq. mm earth wire for circuit wiring for lighting circuis from, DB to Switch boards.

Supplying and fixing PVC conduit as required confirming to IS 9537 (Part-3), ISI marked along with accessories on surface etc. as required:PVC conduit 25 mm. (MMS)

Wiring for circuit/submain alongwith earthwire with the following size of FRLS PVCinsulated coppor conductor , single core cable in surface/recessed medium class PVC conducit as required: (32/40 mm conducit ) 1Rx4C X 6 sq. mm + 2C X 6 sq. mm earth wire earth wire earth wire.

1Rx4C X 10 sq. mm + 2C X 6 sq. mm earth wire earth wire earth wire

Cable end termination of the copper conducor single core wires of 1.1KV volatage grade including supplying and fixing of bimetallic crimping lugs :4C X 6 sq. mm + 1C X 6 sq. mm earth wire earth wire earth wire ckt.)

cable end termination of the copper conducor single core wires of 1.1KV volatage grade including supplying and fixing of bimetallic crimping lugs 1Rx4C X 10 sq. mm + 2C X 6 sq. mm earth wire earth wire earth wire

cable end termination of the copper conducor single core wires of 1.1KV volatage grade including supplying and fixing of bimetallic crimping lugs 1Rx4 C X 16 sq. mm + 2C X 6 sq. mm earth wire earth wire earth wire

Supplying and fixing following way, single pole and neutral, sheet steel, MCB distribution board, 415 V, on surface/ recess,complete with tinned copper bus bar, neutral bus bar, earthbar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator) 8 way (4 + 24),TPN Double door IP43 protection

Supplying and fixing following way, single pole and neutral, sheet steel, MCB distribution board, 220V, on surface/ recess,complete with tinned copper bus bar, neutral bus bar, earthbar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator) 12 Way SPN Double Door IP43 protection

Supplying and fixing 5A to 32 A rating, 240V 10 kA, “C” curve, Single pole miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required.-(6/10A MCB )rating, for Outgoing ckt from LDB's to Switch Board wired on 2.5 mm2 conductor .

Supplying and fixing 5A to 32 A rating, 240V 10 kA, “C” curve, Single pole miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required-16/20A MCB rating -outgoing from PDB's to Socket receptables wired on 4mm2 conductor .

Supplying and installing of RCBOs (Residual current circuit breaker with overload and short circuit protection) ISI marked complete as per I.S. standard conforming to IEC:61009-1 & IS:12640-2, 240/415V 50 Hz with 10 kA short circuit withstand capacity for earth leakage, overload & short circuit protection including connection in existing enclosure in approved manner as per specification .4 pole 25-32Amp, 30mA sensitivity

4 pole 63Amp, 100m/30mA sensitivity

2 pole 40Amp, 30mA sensitivity

Supply of ISI marked and accepted standard of miniature circuit breaker (MCB) of 'C' series with short circuit indication, suitable for 240/415 Volts,50 Cycle, 10 kA/15 kA Value AC supply conforming to IS : 8828 : 1996, IEC : 60898 :2002 & 60947-2 but without enclosures :- MCB FP 50Amp to 63 Amp 10kA rating

MCB FP 6Amp to 32Amp 10kA rating

MCB DP For 40Amp 10kA rating

Supplying, installation, Testing & Commissioning of LED surface mounted Batten light of following body material and construction as per IS : 10322 with driver (Replaceable) as per the requirement with Driver efficiency >85%, Operating voltage AC 140-270 Volt, freq 50/60 hz, Operating temp range -15 deg to 40 deg centigrade, internal surge protection of 2.5 KV with Short & Open circuit protection ,THD < 10% , P. F.≥0.95, IP20, CRI >80 , Flicker free (flicker should be below 5 %), life time (LED,Driver & electrical circuitry), of minimum 50000 Burning Hours with , 70% of initial Lumen maintained till life ends,CCT 3000°K / 4000°K / 5700°K /6000°K /6500°K (As per ANSI Bin), SDCM (Standard Deviation Color Matching) <3, Maximum power consumption should not more than the specified rating and Fixture shall be of relevant BIS standard and trade mark certificate ( T.C.). Manufactures Word Mark/ Name Engraved/ Embossing/ Screen printing on housing. OEM must have its own in house NABL lab setup for all testing facilities for LED fixtures. complete in all respect i/c connections with 1.5 sq mm FRLS, PVC insulated copper conductor single core cable and earthing etc. as required with Minimum 5 year OEM warranty. System lumen efficacy ≥120 <135 lm/Watt output . LM79 & LM80 Test report from NABL lab for all testing required for LED fixtures as per BIS shall be submitted. Shape size and CCT shall be as approved by Engineer-in-Charge as per requirement. (Thermal management: heat sink of aluminium housing such that LED junction temperature shall not rise above 90°C).Powder coated die cast / Extruded aluminium Body (Thickness ≥ 1.20 mm) 24-26 watt

Supplying, installation, Testing & Commissioning of LED Recessed /surface Down lighter (Round/square/ Rectangular) COB Type of following body material and construction as per IS: 10322 with driver as per the requirement with Driver efficiency >85%, Operating voltage AC 140-270 Volt, freq 50/60 hz, Operating temp range 15 deg to 40 deg centigrade, intemal surge protection of 2.5 KV with Short & Open circuit protection, THD 10%, P. F.20.95, IP20, CRI >80, UGR (Unified Glare Rating) 19, Flicker free (flicker should be below 5%), life time (LED, Driver & electrical circuitry), life time of minimum 50000 Burning Hours with 70% of initial Lumen maintained till life ends, CCT 3000°K/4000°K/5700K/6000°K/6500°K (As per ANSI Bin), SDCM(Standard Deviation Color Matching) <3, Maximum power consumption should not more than the specified rating and Fixture shall be of relevant BIS standard and trade mark certificate (T.C.). Manufactures Word Mark/ Name Engraved/Embossing/Screen printing on housing. OEM must mye its own in house NABL lab setup for all testing facilities for LE Jures. "complete in all respect i/c connections with 1.5 sq mm FRLS, PVC insulated copper conductor single core cable and earthing etc. as required with Minimum 5 year OEM warranty. System lumen efficacy ≥120 <135 Im/Watt output. LM79 & LM80 Test report from NABL lab for all testing required for LED fixtures as per BIS shall be submitted. Shape size and CCT shall be as approved by Engineer-in-Charge as per requirement. (Thermal management: heat sink of aluminum housing such that LED junction temperature shall not rise above 90°C). Powder coated die cast /Extruded aluminium Body including trim with Aluminium Reflector Downlighter LED(Single) concealed/surface :22 watt

Supply and fixing of energy efficient with sleek design 10-12 W LED decorative wallbracket Tubelight( Mirror usage) for indoor use made of Alumnium body -Cool white.

Supplying, erecting and testing of approved make Exhaust Fan of 400 mm, 900 rpm with mounting frame, blades AC 230-250 complete connection and including, frame bolt/ Anchor hole fastners etc. complete finished of approved as required.ust have CRCA body having following technical specifications with all accessories including connection with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable i/c hanging arrangement with chain and wiring with GI flexible conduit with coupler (from ceiling surface to false ceiling surface) if necessary and earthing as required.

Supply, Installation, Testing and Commissioning of 1200 mm sweep, BEE 5 star rated, ceiling fan with Brush Less Direct Current (BLDC) Motor, class of insulation: B, 3 nos. blades, 30 cm long down rod, 2 nos. canopies, shackle kit, safety rope, copper winding, Power Factor not less than 0.9, Service Value (CMM/W) minimum 6.85, Air delivery minimum 215 CMM, 350 RPM (tolerance as per IS : 374-2019), THD less than 10%, remote or electronic regulator unit for speed control and all remaining accessories including safety pin, nut bolts, washers, temperature rise=75 degree C (max.), insulation resistance more than 2 mega ohm, suitable for 230 V, 50 Hz, single phase AC Supply, earthing etc. complete as required.1200 mm Sweep,with minimum air delivery 210 m³/min and service value ≥ 4.00 as per BEE.

Supplying and fixing two module stepped type electronic fan regulator on the existing modular plate switch box including connections but including modular plate etc. as required complete in all respects.(for ceiling fans points)

Supplying, fixing and testing of approved make LED bulkhead ABS body, PC diffuser including fixing on wall as required, with necessary material complete

Supplying of ISI marked and approved make of moulded case circuit breaker (MCCB) suitable for 3 phase & N, 4 pole, 50 Hz, 415 Volts, (Ics=100%Icu) AC supply withthermal-magnetic release having respective breakingcapacity (KA) at 415 Volts cited against their rangestandard conforming to IS/IEC 60947-2 MCCB 36kA current rating - 400Amp & adjustable overload setting 80% -100% of In, adjustable short circuit setting 6-10 In 4 Pole

Outgoing:Supplying of ISI marked and approved make of moulded case circuit breaker (MCCB) suitable for 3 phase & N, 4pole, 50 Hz, 415 Volts, (Ics=100%Icu) AC supply withthermal-magnetic release having respective breaking capacity (KA) at 415 Volts cited against their range standard conforming to IS/IEC 60947-2MCCB 36kA current rating - 160 Amp & adjustable overload setting 80% -100% of In, adjustable short circuit setting 6-10 In 4 Pole(Heating Boards)

MCCB 25kA current rating - 125Amp & adjustable overload setting 80% -100% of In, adjustable short circuit setting 6-10 In 4 Pole

Supply of ISI marked and accepted standard of miniature circuit breaker (MCB) of 'C' series with short circuit indication, suitable for 240/415 Volts,50 Cycle, 10 kA/15 kA Value AC supply conforming to IS : 8828 : 1996, IEC : 60898 :2002 & 60947-2 but without enclosures : -MCB DP 50-63Amp 10kA rating

MCB DP For 40Amp 10kA rating

Frequency Metre

Multifunction Meter

Copper bus bar strips with PVC sleeves

Aluminium bus bar strips with PVC sleeves

LED lamp indicator

Supplying of ISI marked and approved make of moulded case circuit breaker (MCCB) suitable for 3 phase & N, 4 pole, 50 Hz, 415 Volts, (Ics=100%Icu) AC supply withthermal-magnetic release having respective breakingcapacity (KA) at 415 Volts cited against their rangestandard conforming to IS/IEC 60947-2MCCB 36kA current rating - 160 Amp & adjustable overload setting 80% -100% of In, adjustable short circuit setting 6-10 In 4 Pole(Heating Boards)

MCCB 25kA current rating - 125Amp & adjustable overload setting 80% -100% of In, adjustable short circuit setting 6-10 In 4 Pole

Incoming :300A TPN Aluminium bus bar strips with PVC sleeves

Supply of ISI marked and accepted standard of miniature circuit breaker (MCB) of 'C' series with short circuit indication, suitable for 240/415 Volts,50 Cycle, 10kA/15 kA Value AC supply conforming to IS : 8828 : 1996, IEC : 60898 :2002 & 60947-2 but without enclosures :-

Frequency Metre

Multifunction Meter

Aluminium bus bar strips with PVC sleeves

LED lamp indicator

Supply of XLPE Insulated power cable (confirming IS-7098 Part-I ) 1100 Volt grade,3½ core/4 core ISI MARKED with Alu. Stranded /solid conductore.3½ CORE ARMOURED3.5C X 240 mm2 Armoured XLPE Aluminum cable

1Rx3.5 coreX 95 mm2 Armoured XLPE Aluminum cable( 3 circuits frp, )

Laying of one number armoured /unarmoured power cable 1.1.KV grade of size exceeding 25sq. mm but not exceeding 120 sq. mm direct in ground including excavation in all soil/ murrum /soft rock, sand cushioning, protective covering and refilling the pit etc. as required.

Laying of one number armoured / unarmoured cable 1.1.KV grade of size exceeding 120 sq. mm. but not exceeding 400 sq. mm direct in ground including excavation in all soil/ murrum /soft rock, and sand cushioning protective covering and refilling the pit etc. as required.

Supplying and fixing crimping type alum. lugs as per I.S.S. specification suitable for following size of cable with alu./copper solid/stranded conductor evenly crimped with high/pressure tool and connected to switch gear/bus/M.C.C.B./M.C.B. etc. as required complete. 240 sq. mm.

4mm to 16 sq. mm

Supplying and fixing flood light with high power LED of 3 to 6 Watt each assembled on single MCPCB and additional unique peanut lens on each LED, system lumens output with efficacy>120 lm/Watt.luminiare having color temp upto 6500K & 50000 hrs. burning life with minimum @ L 70, The colour rendering index of LED light should be more than 80. Luminiare comprises of driver, PF > 0.95 & surge protection 10KV. Housing made of pressure die cast aluminium with heat resistant flat glass, IP65 protection. Submission LM 79-08/IS16106 (2012), IEC60598, IEC61347i/c connection wire,testing etc. to complete the job. 60Watt, color temp 3000-6500k as required.

Supplying & fixing of fire extinguisher/refills as per IS specificationSupplying, Installation Testing & Commissioning of ISI marked CO2 gas type Fire Extinguisher of 4.5 kg capacity conforming to IS: 15683:2018 made from Seamless Cylinder conforming to IS 7285, fitted with ISI marked Control Valve Conforming to IS:3224 discharge adopter complete with initial gas charged with carrying handle and wall mounting bracket etc. as reqd.

Supplying, installation, testing and commissioning of ISI marked ABC stored pressure type fire extinguisher of 6 kg capacity consisting of welded cylinder, squeeze lever discharge valve fitting with pressure indicating gauge with internal discharge tube, discharge nozzle, suspension bracket conforming to IS:15683:2018 duly charged, with ISI marked mono Ammonium Phosphate base ABC powder conforming to IS:4308 and pressurized with nitrogen gas etc. as required.

Supplying & fixing of fire extinguisher/refills as per IS specification 4 buckets set with sand, self-supported M.S. stand i/c shed duly painted with redcolour as per IS.

Supplying & fixing of 25 Kg Trolley ABC Type Fire Extinguisher, wheeled duly painted with redcolour as per IS.

4 buckets set with sand, self-supported M.S. stand i/c shed duly painted with red colour as per IS.

Providing earthing stations at locations as called for Earthing with copper earth plate 600 mm X 600 mm X 3 mm thick including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe of 2.7 meter long etc. with charcoal/ coke and salt as required.

Providing and fixing 4.00 mm dia copper wire on surface or in recess for loop earthing along with existing surface/ recessed conduit/ submain wiring/ cable as required

Providing and fixing 25 mm X 5 mm copper strip on surface or in recess for connections etc. as required.

Please Enable Macros to View BoQ information