GE/PNH-36/2025-26

Amount

B&R PORTION:- Opening of cover (of any description and size) of septic tanks and soakage wells/pits, de-sluding / de-watering contaminated with fine waste materials ( liquid sludge) alongwith solid waste from septic tank and soakage wells/pits of any capacity/depth by mechanical pumping (Truck mounted mechanical machine) / manually making it fully functional to the entire satisfaction of Engineer-in- charge and and removing & depositing the sludge outside the periphery of defence land at a minimum distance of 50 m from nearby living accn and burying in borrow pits including covering with fresh mud and refixing the cover after cleaning / removing the liquid waste material of septic tanks / soakage wells / pits including cutting holes through slab/ wall where required for inserting pipe and making good the same with cement mortar to match with existing surfaces complete all as specified and directed by Engr-in-Charge. Note:-Cost of Taking out sludge, transporting of sludge out side the defence land, earth work & deposition in the pit is deemed to be included in the unit rate to be quoted by tenderer.

Cleaning of under ground sewage lines of 100mm/150 mm bore including manholes, CI stacks.gully traps etc. by means of cleaning by roding from manholes to manholes till the cleared/cleaned water running under sewage line and flushing after cleaning, taking out sludge collected in manholes, removing & depositing the same outside the periphery of defence land in the pit at a minimum distance of 50 m from nearby living accn and covering the sludge in pit with earth and finally spraying unslaked lime, dry, around the manholes including taking off and re-fxing cover of the manhole pit, complete all as specified and directed. Note:-Cost of Taking out sludge, transporting of sludge out side the defence land, earth work & deposition in the pit is deemed to be included in the unit rate to be quoted by tenderer.

Cleaning of blockage of Water Closet (Indian or European) & pipe line upto first manhole manually by Roding and making it fully functional by flushing with water to entire satisfaction of Engineer-in-charge including removing the deposited sludge/solid/liquid material, outside MD land and burying in borrow pits including covering with fresh mud, complete all as specified and directed by Engineer-in-charge. Note:-Cost of Taking out sludge, transporting of sludge out side the defence land, earth work & deposition in the pit is deemed to be included in the unit rate to be quoted by tenderer.

Demolition or breaking up drain pipe of 100/150 mm dia bore (salt glazed stone ware, AC, PVC or reinforcement concrete) set in cement mortar/concrete complete all as specified and directed.

S&F 150 mm bore salt glazed stone ware drain pipes, grade ‘A’ laid in trenches and jointed in CM 1:3, complete all as specified and directed by Engr-in-Charge.

Excavation in trenches n.exc 1.50m wide and n.exc 1.50m in depth for foundation etc. and getting out in any type of soil, complete all as specified and directed.

Returning, filling in, including spreading, leveling, watering and well ramming in layers not exceeding 25cm, in any type of soil, complete all as specified and directed.

Removal of excavated material to a distance not exc 50m and depositing where directed at a level not exceeding 1.5mtr above starting point complete all as specified and directed.

M&L for concrete bed to drain pipes including packing under and haunching against the sides of pipes for 150mm SGSW pipe after they are laid in PCC (1:4:8) type D-2 (using 40mm graded crushed stone aggregate) & tested, complete all as specified and directed.

Demolition of cement concrete (reinforced) of any description and in any position not otherwise specifically described (reinforement cut as required to facilitate demolition), complete all as specified and directed by Engineer-in-Charge.

M&L for precast cement concrete 1:2:4 type B1 (20mm graded crushed stone aggregate) as in landings, cover slab for man holes etc set in cement mortar(1:6), complete all as specified and directed.

S&F TMT bars, 8mm dia and over, cut to length, bent to shape required including cranking, bending spirally or hooping for column, hooking ends and binding with and including mild steel wire(annealed) not less than 0.90mm dia complete all as specified and directed.

Demolition of cement concrete (un-reinforced) of any description and in any position not otherwise specifically described complete all as specified and directed by Engineer-in-Charge.

Demolition of brick or stone masonry, built in cement mortar including all quoins, arches, pillars etc but excluding ashlars facings, dressed stone work, complete all as specified and directed.

M&L for Walling of random rubble stone masonry brought upto course, well bonded, bedded and solidly hearted, built in cement mortar (1:6), complete all as specified and directed.

All as per Srl item No. 15 above, but except stone complete all as specified and directed.

M&L for brick work with sub class ‘B’ bricks straight or curved on plan exceeding 6m mean radius built in cement mortar 1:6, complete all as specified and directed.

Extra over stone walling for hammer dressing with maximum depression on face from straight edge held against the dressed surface not exceeding 40mm to face stones (lime and sand stone) and dressing of face beds and joints, complete all as specified and directed.

M&L for cement concrete (1:2:4) type-B-1 (using 20mm graded stone crushed aggregate) as in lintels upto 1.5 metre clear span, cills, steps, siesmic and other similar bands, plinth courses, string courses, lacing courses, parapets and railing upto 60cm height, copings, bed block, kneelers, apex stones, bed plates, roof kerbs round or chamfered on edges, water troughs, in edging of path (interlocking paver) and the like including weathering, slightly rounded or chamfered angles and throatings etc.including necessary form work complete all as specified and directed by Engineer-in-Charge.

Taking down cement plastering on lathing (other than wire netting) without removing lathing complete all as specified and directed.

M&L for 15mm thick rendering in CM 1:4 on other than fair faces of brick or stone masonry surfaces & finishing the surface even and smooth without using extra cement, complete all as specified and directed.

M&L for 75mm thick PCC 1:4:8 type D-2 (using 40mm graded crushed stone aggregate) as in sub base to flooring/path etc. finished even & fair, complete all as specified and directed.

M&L for chequered cement concrete tiles with chemical resistant coating if size 300x300x 25mm thick, set & jointed in neat cement slurry in floors and pointed with grey cement mixed with pigments, laid over and including 20mm thick screed bed in CM 1:4, complete all as specified and directed.

M&L for spreading, laying of sand as in cushioning under floors before laying of blocks incl watering & consolidation, complete all as specified and directed.

M&L for machine pressed precast concrete interlocking paver block any shape and size confirming to IS-15658-2006 of 80mm thickness M-40 Grade,laid jointed pointed with grey cement and no pigments, complete all as specified and directed by Engr-in-Charge. Note: The sample shall be got approved by GE before bulk procurement & lot shall be got tested independently by the GE.

M&L for machine pressed precast concrete interlocking paver block any shape and size confirming to IS-15658-2006 of 60mm thickness M-35 Grade,laid jointed pointed with grey cement and no pigments, complete all as specified and directed by Engr-in-Charge. Note: The sample shall be got approved by GE before bulk procurement & lot shall be got tested independently by the GE.

S & F in repair PVC (SWR) pipes 75 mm dia any length single socketed with rubber ring joint, laid in floor/walls, complete all as specified and directed.

S & F in repair PVC (SWR) pipes 110 mm dia any length single socketed with rubber ring joint, laid in floor/walls, complete all as specified and directed.

S & F in repair PVC (SWR) bends any radius, diminishing pieces or tapers of 75 mm bore, complete all as specified and directed.

S & F in repair PVC (SWR) bends any radius, diminishing pieces or tapers of 110 mm bore, complete all as specified and directed.

S & F in repair PVC (SWR) branch pieces, double (double Y) equal or unequal of 75 mm bore, complete all as specified and directed.

S & F in repair PVC (SWR) branch pieces, double (double Y) equal or unequal of 110 mm bore, complete all as specified and directed.

S&F in repair PVC (SWR) floor trap of 75mm dia of outlet, plain with grating including jointing to waste pipe with solvent cement fixed, complete all as specified.

S&F in repair vitreous china wash down water closet pan (pedestal pattern), white (excluding fixing bolt, flushing cistern and flushing pipe) complete all as specified and directed.

S&F in repair vitreous china squatting pan (Orissa pattern) size 580 x 440 mm, snow white, with 'P' or 's' trap, front or back inlet and integral foot rests, complete connection to drain (outgoing pipe) and to flushing pipe and syphonage pipe etc. including lime concrete bedding, complete all as specified and directed.

S&F in repair PVC valve less syphonic action type flushing cistern 10ltr capacity , low level white with inlet ball valve float and handle including brackets including 32mm dia PVC. flush pipe for low level cistern including all joints complete all as specified and directed.

M&L for on site LLDPE septic tank designed to carry sewage and sullage water, incl excavation in any type of soil, 100 mm thick PCC 1:4:8 in foundation incl vent shaft, connection etc, for 20 users incl returning, filling and removal of excess soil and incl demolition of existing tank complete all as specified and as shown on drawings.

M&L for construction of soakage well 1.80 mtr dia and 2.90 mtr deep below inlet (depth) from inlet pipe to ground level 45 cm, including excavation and earth work in hard / dense of soil, PCC 1:3:6 type C-2 (using 40 mm graded crushed stone aggregates) in foundation, wall in honey combed brick work in CM 1:4, cover slabg of M-25 (Design mix), filling with brick bats, earth cushion on brick lining on top and inlet pipe 150mm dia, incl demolition of existing soakage well complete all as specified and as shown on drawings.

S & F in repair galvanised, 2 strand, steel barbed wire 2.24 mm dia barbed with 2mm dia barbs at 75 mm spacing and straining and fixing to any type of standard rails straining bolts, incl securing or tying at crossing with and provision of galvanised mild steel wire, staples or steel pins, etc. complete all as specified and directed.

Dismantling wrought iron or mild steel work of any description complete all as specified and directed.

Excavation in post holes (or similar holes) each n exc 0.5 cu.m, getting out in any type of soil(soft/loose and hard/dense soil), returning, filling inand ramming earth or broken rubble mixed with earth around, in layers not exceeding 25cm, watering, and removing surplus soil to a distance n exc 50m and making good surface complete all as specified and directed.

M & L for mild steel as in posts and struts in fencing including cutting tops to shape as directed, drilling holes, notching for wire, etc.; flat iron fillets (for securing wire mesh etc.) including all necessary drilling, bolting or riveting, etc., and similar work conforming to Fe 290 Gde E-165 complete all as specified and directed.

S&F mild steel screw bolts (machine made) with hexagonal or square heads at one end and screwed the other, or screwed both ends, each screwed end to be fitted with washers and one hexagonal or square nut,length of bolt not exc 5 cm and 11 to 15 mm dia complete all as specified and directed.

Dismantling fencing wire mesh, any type ccomplete all as specified and directed.

Fixing only chain link fencing including line wires, any mesh, size and type to any type of standards, rails, straining bolts, etc. including provission of binding wire complete all as specified and directed.

Supply only chain link MS galvanisd fencing, any size or type complete all as specified and directed.

M&L for mild steel work conforming to Fe-290 (Gde E-165) as in grills, gratings, steel doors etc. with ends of bars shouldered and/ or riveted or forged into spikes framed guard bars, and similar works complete all as specfied & directed.

M&L for applying two coats of synthetic enamel paint over a coat of red oxide primer to new or previously untreated steel surfaces over 10cm width or girth including preparation of surfaces, complete all as specified and as directed.

M & L for plain cement concrete 1:2:4 type B-2, using 40mm graded crushed stone aggregates as in surfaces channels and drain complete all as specified and directed.

E&M PORTION:- Taking down carefully copper/ aluminium unserviceable/ perished point wiring (light, fan, socket or power complete including fixture and fittings such as switches, ceiling roses, pandents, regulators, sockets, light fittings,removing material from site for taking credit etc and making good disturbed surfaces of wall, floors, complete all as specifiecd and directed.

M&L for point wiring with two single core 1.5 Sqmm (nominal cross section area) FRLS PVC insulated unsheathed multistranded copper conductor cable and one single core 1.5 Sqmm (nominal cross section area) FRLS PVC insulated unsheathed multistranded copper conductor cable as earth continuity to common earth and connecting to earth dolly running in and including PVC casing & caping (ISI marked) of suitable size with PVC boards of appropriate sizes and all requisite accessories such as PVC elbow, Tee, collars, bends etc. with PVC terminals box & cover for mounting swtches, sockets, fan regulator etc for mounting switches, sockets, fan regulators etc complete all as specified and as directed for the following :-

One light/fan/bell point controlled by one way switch 6 Amp complete all as specified and directed.

One 3/5 pin socket outlet 6 amp on same board complete all as specified and directed.

One 3/5 pin socket outlet 6 amp independent board complete all as specified and directed.

Onelight point controlled by two 2 way switch 6 Amp complete all as specified and directed.

All as per srl item No 51 here in before but for one 3 pin socket outlet 16/20 Amp independent with two single core 2.5 Sqmm size cable as phase & neutral and one single core 2.5 Sqmm as in continuous earth wire complete all as specified and directed.

S&F ceiling rose, 3 terminal, surface bakelite 65 mm x 50mm, PVC/poly carbonate, insulated body, complete all as specified and directed.

S&F switch piano flush type 6 Amp single pole one way, (ISI marked), complete all as specified and directed.

S&F switch piano type, flush type,2 way ,6 Amps , (ISI marked), complete all as specified and directed.

S&F switch piano bell push flush type 5 Amp single pole one way (ISI marked) complete all as specified and directed.

S&F socket outlet 2 in 1, 3 pin, 6 Amp flush type universal, complete all as specified and directed.

S&F Switch socket combination, 5 pin, 5 Amp flush type universal, complete all as specified and directed.

S&F Switch socket multipurpose combination 2 in 1, 5 pin, 5 and 15 Amp flush type universal, complete all as specified and directed.

S&F Lamp holder PVC/Polycarbonate type with back plate suitable for batten fittings, complete all as specified and directed.

S&F stepped type electronic fan regulator flush type on the existing phenolic laminated sheet etc. for 1200 / 1400mm sweep, complete all as specified and directed.

S&F electric bell ding dong type 230 volts AC supply 50 Hz complete all as specified and directed by Engineer-in-Charge.

Supply and fixing in repair LED batten 1x 20W wall mounted with polycarbonate housing & integrated electronic driver and connecting up with with three core flexible copper conductor cable of suitable size from ceiling rose complete all as specified and directed.

Supply and fixing in repair LED light fitting mirror type with high out put diffuser 2 feet, 10 watt 220 V AC decorative type with driver holder and LED lamp including connecting up with three core flexible copper conductor cable of suitable size complete. all as specified and directed.

S & F in repair LED light fitting 1x9W/1X10W bulkhead luminaires including LED light driver holder connecting up with three core flexible copper conductor cable of suitable size. complete. all as specified and directed.

Supply and fixing in repair LED luminaire 600 mm x 600 mm, 35/36 watt, 220 V AC recessed type with high efficiency PMMA diffuser soft glare free light complete with driver, holders & LED lamp suitable for roof ceiling including connecting up with driver three core flexible copper conductor cases of suitable size complete all as specified and directed.

S&F in repair gate light fittings, outdoor type, high power , 25 watt, IP65 luminaire, prewired with suitable pole for mounting complete all as specified and directed. Make: Havells cat part No. Coral Opal IP65 or equivalent make as mentioned in PS

Supply and fixing in repair LED street light fitting 35 Watt 230 V AC outdoor type with high pressure die cast aluminum hosing and heat resistant complete with driver including suitable bracket fixed to wall/ pole complete with IP 65/66 protection complete all as specified and directed.

S&F in repair LED inverter lamp CDL 10 /12 watt with holder base (B22) type, complete all as specified and directed.

S&F in repair LED driver suitable for 34 watt LED ceiiling light fittings and making connection to fitting complete all as specified and directed.

S&F in repair single pole and neutral enclosure with a two pin and metal earth plug and socket complete with & incl one single pole MCB of 20 Amps complete all as specified and directed.

S&F in repair sheet metal enclosure for DBs, vertical TPN double door (IP43), 4 ways built in bus bars suitable for 415 volts, AC, 50 Hz and suitable for FP MCCB as incommer and out going SP/TP MCBs complete all as specified and directed. Note:- MCBs shall be measured and paid separately.

S&F in repair sheet metal enclosure for DBs, SPN double door (IP43), 4 ways built in bus bars suitable for 240 volts, AC, 50 Hz , including connecting both incoming and outgoing cable termination with proper taping, lagging testing and commissioning complete all as specified and directed.

S&F in repair sheet metal enclosure for DBs, SPN double door (IP43), 8 ways with 200 amps rated bus bar suitable for 240 volts, AC, 50 Hz, including connecting both incoming and outgoing cable termination with proper taping, lagging testing and commissioning complete all as specified and directed.

S&F in repair sheet metal enclosure for DBs, SPN double door (IP43), 12 ways with 200 amps rated bus bar suitable for 240 volts, AC, 50 Hz, including connecting both incoming and outgoing cable termination with proper taping, lagging testing and commissioning complete all as specified and directed.

S&F in repair MCB TPN 40-63 amps 415 volts 10 KA 'C' series, complete all as specified and directed.

S&F in repair MCB SPN 40-63 amps 415 volts 10 KA 'C' series, complete all as specified and directed.

S&F in repair MCB single pole 6 to 32 amps 240 volts 10 KA 'C' series complete all as specified and directed.

S&F in repair Switch socket multipurpose combination 5 in 1, 20/16 amp flush type universal including box with 4 fixing holes, complete all as specified and directed.

S&F in repair Switch socket multipurpose combination 2 in 1, 6 amp flush type universal including box with 4 fixing holes, complete all as specified and directed.

Taking out old unsv exhaust fan from site and providing new exhaust fan made up of sturdy engineering plastic complete with louvers shutter, voltage 230 V, 50 Hz, 1200 RPM, copper winding of sweep 300mm incl all connecting accessories complete all as specified and directed by Engineer-in-charge.

Taking out old unsv exhaust fan from site and providing new exhaust fan made up of steel body, AC single phase, voltage 230 V, 50 Hz, copper winding of sweep 300mm incl all connecting accessories complete all as specified and directed by Engineer-in-charge.

Taking out old unsv exhaust fan from site and providing new exhaust fan made up of steel body, AC single phase, voltage 230 V, 50 Hz, copper winding of sweep 450mm incl all connecting accessories complete all as specified and directed by Engineer-in-charge.

S&F in repair PVC casing caping of size upto 32 mm incl all fixing accessories complete all as specified and directed.

S&F Earthing complete with galvanized steel earth plate electrode 60cmx 60cmx6mm thick buried directly in ground (earth pit not less than 2.25m deep below normal ground level) with top edge of the plate not less than 1.5m below normal ground level, connected to galvanized iron wire 4.0mm dia by means of bolts, nuts and washers of galvanized iron or steel, protected by GI light grade pipe 15mm bore including GI light grade water pipe 20mm dia with funnel all as shown in electric plate No. 3 of 2009 SSR Pt-I and testing complete including earth work in any type of soil, PCC 1:2:4 type B-1 as in earthing pit and cover 50mm thick reinforced with 6mm dia MS round bar @ 10cm C/C both way and MS frame, common salt, charcoal and testing on completion including dismantling unsv earthing, complete all as specified and directed.

S&F in repair Sub main wiring with single core cable 2x 4 Sqmm FRLS insulated unsheathed stranded copper conductor cable 1100 Volts grade including surface PVC casing caping medium grade alongwith 1x 4 Sqmm FRLS insulated unsheathed copper conductor cable as earth wire connected with main earth dolly, complete all as specified and directed. Note:-Three wire of 4 Sqmm and one run of pvc conduit/casing caping shall be measured as one unit.

S&F in repair Sub main wiring with single core cable 2x 6 Sqmm FRLS insulated unsheathed stranded copper conductor cable 1100 Volts grade including surface PVC casing caping medium grade alongwith 1x 6 Sqmm FRLS insulated unsheathed copper conductor cable as earth wire connected with main earth dolly, complete all as specified and directed. Note:-Three wire of 6 sqmm and one run of PVC conduit/casing caping shall be measured as one unit.

S&F 1100 volts grade heavy duty cable PVC insulated solid aluminium conductor served with PVC tape and over all PVC sheathed in service connections suspended by insulating hangers not more than 1 m apart including 4mm dia GI suspension wire, one twin core cable flat or circular of size 6 Sqmm 2 core & including taking down old old unsv service cable connection, complete all as specified and directed.

S&F 1100 volts grade heavy duty cable PVC insulated solid aluminium conductor served with PVC tape and over all PVC sheathed in service connections suspended by insulating hangers not more than 1 m apart including 4mm dia GI suspension wire, one twin core cable flat of circular of size 10 Sqmm 2 core including taking down existing old service connection, complete all as specified and directed.

Repair and maintenance of unserviceable ceiling fan of 1200mm/1400mm sweep at contractor's work shop, incl dismantling complete the ceiling fan parts, inspecting serviceability of all the parts, refixing of serviceable parts after cleaning and replacement of unserviceable parts with company's genuine parts i.e. capacitor, bearing, bushes, shaft, bracket, rubber bush, connecting wire, PVC connector, aluminium clamp for rod, bracket, bush rod, greasing/oiling etc assembling, cleaning and testing of ceiling fan complete all as specified and directed. Note: (i) Unserviceable parts as above shall be measured and paid separately under relevant items of Sch 'A' as supply only. (ii) Rewinding of stator will be measured & paid for separately under relevant item of Sch 'A'. (iii) Cost of minor part i.e. Cotter pin, screws shall be deemed to included in the cost of quoted rate.

Supply only bearing good quality for ceiling fan 1200mm/1400mm sweep ISI marked complete all as specified and directed.

Supply only Gun metal bush for ceiling fan 1200mm/1400mm sweep complete all as specified and directed.

Supply only capacitor 2.5 mfd ISI marked complete all as specified and directed.

Supply only brass bracket assy for hanging the ceiling fan 1200mm/1400mm sweep complete all as specified and directed.

Supply only 3 core flexible wire 40/.0076, white colour from ceiling rose to fan connector complete all as specified and directed.

Supply only shaft for ceiling fan complete all as specified and directed.

Taking out old unsv ceiling fan from site of capacity 1200/1400 mm sweep and providing new ceiling fans complete with blades, down rods, electronic regulator and accessories, 230 V, 1200 mm sweep, min air delivery 210 CFM with service value 6.00 BEE. Five star rated with brushless direct current motor (BLDC) incl all connecting accessories complete all as specified and directed by Engineer-in-charge.

M&L for removing of old burnt winding of ceiling fan any size, type and rewinding with superior quality copper wire with insulation complete all as specified and directed.

Repair and maintenance of unserviceable exhaust fan of any cap and sweep by dismantling the exhaust fan parts, inspecting the serviceability of parts, refixing of serviceable parts after cleaning, replacement of unerviceable parts i.e. beaing, bush, capacitor, connecting wires, fan blade, locknut, rubber pad etc, oiling/greasing, cleaning and testing of exhaust fan complete all as specified and directed. Note: (i) Unserviceable parts replaced shall be measured and paid separately under relevant items of Sch 'A' as supply only. (ii) Rewinding of stator winding shall be measured & paid for separately under relevant item of Sch 'A'. (iii) Cost of minor part i.e. screws shall be deemed to included in the cost of quoted rate.

Supply only double ball bearing (ISI marked) for exhaust fan of 200 mm sweep to 450 mm sweep fan complete all as specified and directed.

Supply only gun metal bush for Exhaust fan of any capacity. complete all as specified and directed.

M&L for rewinding of 450mm sweep exhaust fan motor with superior quality copper winding wire with insulation complete all as specified and directed.

M&L for rewinding of 300mm sweep exhaust fan motor with superior quality copper winding wire with insulation complete all as specified and directed.

Supply only blade of exhuast fan of 200 mm sweep to 450 mm sweep as per existing make complete all as specified and directed.

M/S GURU DEV BUILDERS (BID ID -3344106)

M/S MAHALUXMI BUILDERS (BID ID -3344117)

M/SHansrajbuilder (BID ID -3344161)

R C TRADERS (BID ID -3344648)

K S BUILDERS (BID ID -3344736)

M/S KHAN ENTERPRISES (BID ID -3344207)