Construction of New shop building at Mondaikadu Colachel road (Re.Sy.No. 93/4) in Mondaikadu Town Panchayat

Amount

Earthwork excavation in all soils and sub soils except hard rock requiring blasting with initial lead and lift including re-filling the sides of foundation in layer of 15 cm thick watering , ramming ,depositing the surplus earth in the premises as directed by departmental officers etc., complete as per SS 20 B TNDSS NO: 23&24VI (S2), VII 9,10

Plain cement concrete Using 1:4:8 mix ( One cement , four Sand and Eight aggregates) using 40 mm ISS HBG metal including cost and conveyance of all materials to work site and all labour charges for mixing, laying,consolidating and curing etc complete as per the standard specifications. TNDSS NO: 28 V, VI (S2) V,VI (S5A) VII

Supplying and erecting steel centering for sides and soffits including supports and strutting upto 3.29 m height for plain surface as RCC slabs, rectangular tee (or) elbeams, lintel, bed block stair case waist slab, landing slab, etc., complete as per standard specification - 10m2 as per TNDSS & Morth specification No:30 & 36

Footing, Grade beam

Beam RCC slab

Column

Side wall

Reinforced cement concrete 1:11/2:3 (one cement one and half sand and three aggregate) using 20mm size I.S.S. metal including cost conveyance of materials to site and all labour charges etc., mixing laying consolidating curring etc., but excluding cost of steel etc., complete as per standard specification as per TNDSS NO: 30 V,VI (S3) VII-3

Upto basement

Ground floor

First floor

Supplying, fabricating and placing in position of mild steel or TMT rods, including cost of steel and binding wire and all labour charges for cutting, bending, tying and placing in position etc, complete as per SS. TNDSS NO: 97 V,VI (S6) VII (S6) VII-3

Brick work in cement mortar 1:5 mix using (One cement and five sand) using best quality of III class Country bricks of size (8 3/4"x4 1/4"x 2 3/4") for foundation including curing cost and conveyance of all materials to site and all labour charges etc., complete as per standard specification TNDSS specification No.31 & 31C

Upto basement

Ground floor

First floor

Plastering in cement mortar 1:3 (one cement three sand) using 10mm thick including cost and conveyance of all materials and labour charges etc, complete as per standard specification. [MoRTH Specification: Clause:1000/1300]

Plastering in cement mortar 1:5 (one cement, five sand) using 12mm thick including cost and conveyance of all materials and labour charges etc, complete as per standard specification. TNDSS NO: 61 V,VI (S4)

Painting two coats with ready mixed Plastic Emulsion Paint S.I.358 Plastic emulison paint of'approved quality and colour over a priming coat, including thorough scraping, clean removal of dirt, etc complete and including necessary plaster of paris, putty, wherever required including cost and conveyance of all materials etc.and all lobour charges etc.complete as per Standard specification and as directed by the departmental officers. TNBP No:66-A (Sl.No.358)

Painting two coats over new iron work with ready mixed paint of apprved quality and colour including cost of all materials and labour charges etc complete as per SS

Floor Finishing First Quality Design Ceramic tiles of All colours of sizes 305mm x 305mm x 6mm. laid in cm 1:3 mix 10mm thick and pointing with white cement using 0.4kg/sqm including finishing the joint and pointing flush with tiles surface etc complete

Paving the floor with Plain/Design Ceramic tiles ( Colour and shade as directed ) of Stain Free Nano Polish Vitrified Tiles of size 600 x 600 x 8mm in all floors over a base layer of cm 1:3 mix 20mm thick laid in situ and pointed with same coloured cement ( white cement mixed with colouring pigment ) neatly and fixed in position so as to make it perfectly smooth and shining,to the alignment etc.complete complying with standared specifications and as directed by the departmental officers. The sample colour and shade of the ceramic tiles should be got approved from the departmental officers before use in the works

Dadooing with glazed tiles of 300mm*200mm*6mm size of approved quality and colour set in c.m 1:2mix (one cement and two sand) 10 mm thick and pointing with white cement using 0.4 kg /m2 neatly as directed -including cost of all materials and labour charges etc complete as per SS

Solid PVC door shutters using 19 Gauge 19mm MS square tubes for styles and outer frames. 15mm MS square tubes for top, lock and bottom rails. The steel tubes shall be covered with 5mm thick solid PVC sheets. Shutter using 5mm thick solid PVC sheets for panelling shall rigidly fixed in position including necessary furniture and fittings. The over all size of styles shall be 50mm x 30mm. The over all size of top rail, Lock rail and bottom rail shall be 75mm x 30mm. The over all size of frames shall be 50mm x 45mm, with suitable rabate for housing the shutter.

Supplying and fixing UPVC (Un-Plasticized Polyvinyl Chloride) Louvered Ventilators of from the profile the size of outer frame 60mm x 58mm and shutter profile size of 60 x 78mm both profiles are reinforced with GI/1mm 125GSM and 100% corrosion free, the profile are multi chambered sections with wall thick of 2mm. The EPDM rubber (black colour) covered with all over the edges of frame and shutter. The corners and joints should be welded and cleaned. Radiations pin headed glass 4mm thick should be provided in the louvers. The window should be fixed to the wall with 100% packing with screws and silicon packing all round the frames. The ventilator should be got approved from the Executive Engineer before use on work

Manufacturing, Supplying and Fixing of Stainless Steel Hand rails for staircase using 50mm dia 304L Grade Stainless Steel pipe of 1.60mm thick at required locations to a height of 900mm from finished floor level welded to 38mm dia Stainless Steel pipe post of 1.00mm thick as vertical at 900mm centre with 2 Nos. of 25mm dia intermediate horizontal stainless steel pipe of 1.60mm thick in between. The vertical pipe has to be welded to the 100 X 100 X 6mm MS base plate encased in the base concrete. The rate is inclusive of the charges for cutting, bending, welding, grinding, polishing, conveyance, electrical charges, etc. complete

Supply and fixing of mild steel grill works for door, windows, ventilators, etc including redoxide priming coat and cost of materials and all labour charges etc. complete.

Earthing as per the ISI specification with an earth electrode of 2.10 metre Class 'B' GI pipe of dia not less than 40mm with copper earth plate of size 125mm x 50mm x 6mm with necessary funneling arrangements with necessary masonry work and with 38mm RCC cover slab for the brick masonry (SD-221)

Supply and run of 2 of No.8 SWG GI wire for guarding with cradle with No.8 SWG GI wire at the equal interval of 1.5metre (SD-75)

Supply and fixing of 7 segment 4 way TPN MCB sheet steel distribution board (Higher end) with metal / acrylic door cover flush type /surface type fitted with busbars and neutral links with single / three phase MCB outgoings and seperate 4 way provision for accomodating one No 4 pole incoming MCB / Isolator and another seperate 4 way provision for accomodating one No 4 pole ELCB / RCD (totally 8 ways in one segment) (3x 4 ways in Each segment) and seperate provision for MCB / Isolators ( totally 12 Nos) for sub incomers in 3 segments with lable holder and provison for taking up cable for size not less than 35 sq.mm. with the following on wall with Earth connection only. (SD-627)

Supply and run of 2 of 1.5 sq.mm. PVC insulated SC unsheathed FRLS copper conductor of 1100V grade in rigid pipe concealed in wall and ceiling with continuous earth wire connection of 1.5sq.mm copper wire and making good of the concealed portion with suitable colour (SD-55)

Supply and run of 2 of 1.5sq.mm. PVC insulated SC unsheathed FRLS copper conductor of 1100V grade in suitable PVC rigid pipe on wall and ceiling with continuous earth wire connection 1.5 sq.mm copper wire with painting of suitable colour (SD-54)

Supply and fixing of TNEB meter board suitable for 32A single phase service connection with 32A fuseunit (500V) 32A neutral link and earthlink (1" x 1/8" copper flat) on TW plank of size 375mm x 300mm x 19mm with supporting TW reepers of 1" thick an either side with painting with suitable bolt and nuts for fixing the TW plank on wall with earth connection and interconnection with 7/20 PVC insulated copper wire from EB meter to fuse unit with 1 No 40 Amp 30 MA Double Pole RCD / RCCB (Lower End) with suitable necessary connection (SD-126)

Supply and providing cable end termination of 3-1/2 x 95sq.mm. PVC LTUG aluminium armoured cable with necessary aluminium cable sockets by crimping etc with electrical connection complete (SD-227)

Wiring with 2 x 1.5 sq.mm. PVC insulated SC unsheathed FRLS copper conductor of 1100V grade in suitable PVC rigid pipe concealed in wall and ceiling with PVC accessories inflush with wall with 3mm thick hylum sheet cover with TW switch box and 5AFT switch with continuous earth wire connection of 1.5 sq.mm copper wire for making good of the concealed portion with suitable colour for PVC concealed light point / fan point (for electronic regulator) (SD-23)

Wiring with 2x1.5sqmm (22/0.3) PVC insulated SC unsheathed Cu.Conductor of 1100 V grade in suitable PVC rigid pipe concealed in wall and ceiling with PVC accessories, in flush with wall, with 150mm x 100mm x 113mm TW switch box with 3 mm thick Hylem sheet cover for 5 A 3 pin non inter locking CS Plug with continuous earth wire connection of 14 SWG TC wire and making good of the concealed portion with suitable colour for concealed PVC plug point. (SD-38)

Supply and fixing of 18W LED square type Recessed fitting with LED (Higher end) on false Ceiling with suitable hanging support from ceiling with PVC unsheathed copper leads from terminals to the fitting. (SD-450)

Supply and fixing of 300mm (12") sweep (light duty) AC exhaust fan complete with necessary wall opening and making good of the wall (SD-114)

Supply and delivery of following PVC / G.I pipes and specials

110mm PVC pipe

90mm PVC pipe

25mm PVC pipe

32mm PVC pipe

110mm PVC Elbow

75mm PVC elbow

110mm PVC elbow with door

75mm PVC elbow with door

110mm PVC Tee

75mm PVC Tee

110mm PVC Tee with single door

75mm PVC Tee with single door

110mm PVC "Y" with single door

90mm PVC "Y" with single door

25mm PVC coupler

32mm PVC coupler

25mm PVC Elbow

32mm PVC Elbow

25mm PVC bend

32mm PVC bend

25mm PVC Tee

32mm PVC Tee

25mm PVC End cap

32mm PVC End cap

20 x 15mm PVC Reducer

25 x 20mm PVC Reducer

32 x 25mm PVC Reducer

20 x 15mm PVC Reducer elbow

25 x 20mm PVC Reducer elbow

32 x 25mm PVC Reducer elbow

25mm Jet Nipple

32mm Jet Nipple

Supplying and fixing in position best quality and approved make Indian made white / colour glazed earthernware wash hand basin of size 550 x 400mm (with pedestal / without pedestal) with a pair of cast iron brackets, including cost 15mm dia brass CP pillar tap, 32mm dia "B" class GI waste pipe with rubber plug and chain, 15mm dia GM wheel valve, 15mm brass nipple, 15mm dia nylone connection, 32mm dia CP brass waste coupling including fixing of wash basin using CI brackets on to the wall in position with TW plugs and screws, rubber washers, white lead and giving necessary water supply connection and painting the brackets with two coat of painting over a priming coat of anti-corrosive paint including testing for leakages etc., complete complying with standard specification and as directed by the departmental officers. (The wash hand basin and specials should be got approved by the Executive Engineer before use on works).

Supplying and fixing in position colour Europen water closet with low level flushing tank of 10 lit capacity of best quality and approvel make with 100mm 'p' or 's' trap with double flapped rigid PVC seat cover with CP brass etc. Complete complying with standard specifications and as directed by the department officers ( EWC should got approvel by the executive work before use on work.)

Providing and fixing 6" dia PVC rain water down fall pipes with necessary PVCshoes, pvcbends, other specials clamps, screws, nails, teekwood plucks etc, complete including cost of all materials and labour charges as per SS. for 110mm dia pipe 4 kg. per cm2

Supplying and fixing in position first quality and approved variety of Gun metal Gate Valve / Wheel Valve with BIS make of the following dia including cost of shellac, thread balls, etc., complete complying with standard specifications (for both internal and external water supply arrangements). The valves to be used on work shall be got approved by the Executive Engineer before use on work.

25mm Gun Metal Gate valve

32mm Gun Metal Gate valve

Supplying and fixing position CI Nahani Trap / Floor Trap of the following sizes with best stainless steel gratings of approved brand and quality, fixed over a bed of PCC 1:4:8 and finished with Cement Mortar 1:3 (One Cement, Three sand) including dismantling masonry works wherever found necessary and making good the dismantled portions to the original condition and giving connection to the CI / PVC pipes, etc., complete complying with standard specification. (The Nahani Trap should be got approved by the Executive Engineer before use on works)

Supply and delivery and fixing of 1000 litre HDPE tank as per IS 12701 / 1996 including loading, unloading, transportation and labour charges for fixing of the GI pipes and specials for pipe connection works including cutting, threading and fixing charges etc. complete.

V.DEVA HARIN SAM (BID ID -1483439)