REPAIR TO ROAD, CULVER AND SIDE BERMS IN TECH AREA AT AF STN SURATGARH

Amount

Scarifying or picking graveled macadam or bituminous macadam surface in area n.exc 400 sqm and exc.50mm & n.exc 100mm deep complete all as specified and directed.

Material and labour for Repair to pot holes any depth, not exceeding 1 Sqm each including sweeping free from dust and mud, or water, scoring sunken surfaces in road, paths etc; cutting around edges to at least 25mm in depth, making good by applying tack coat at 5 Kg per 10 Sqm (using paving bitumen of grade VG-10) putting in premixed bituminous macadam using paving bitumen of grade VG-30) blinded with 0.09 Cum of stone chippings, 6.3mm size and again well rammed (including supply of premixed macadam, binder and chipping), depth of pot holes exceeding 30mm complete all as specified and as directed by the Engineer-in-Charge.

Material and labour for premix bituminous macadam laid/rolled and compacted to required gradient and camber (consolidated thickness 75mm or less) using paving bitumen complete all as specified and directed. (binder shall be of 4% weight of total mix)

Applying evenly a priming/ tack coat with bituminous primer using paving bitumen of grade VG-10 at 10 Kg per 10 Sqm complete all as specified and directed.

Material and labour for preparing existing black top surfaces by brushing with wire brushes for removing caked mud etc, sweeping with brooms and finally fanning with mechanical compressor the cleaned surface with gunny bags to remove all loose dirt etc complete all as specified and as directed by Engineer in charge

Applying evenly a priming/ tack coat with bituminous primer using paving bitumen of grade VG-10 at 5 Kg per 10 Sqm complete all as specified and directed.

Material and labour for bituminous premixed semi dense asphalted concrete 30 mm consolidated thickness using paving bitumen of grade VG-30 @ 5.5% binder content by weight of total mix, spread by means of self propelled mechanical spread/pavers rolled and compacted to required camber and gradient by using mechanical power road roller 8 to 10 ton capacity complete all as specified and as directed by Engineer-in-charge.

Material and labour for preparation of black top surfaces of road and applying one coat of retro-reflective thermoplastic road marking paint conforming to clause no 803.4 of "Specification for Road & Bridge Works" issued by MORT&H (Ministry of Road Transport & Highways) complete all as specified & directed.

Supply and fixing in repair delineator (Model DA 952 GP of Dark Eye) of ABS round body fitting with 2 Nos 100mm dia highly reflective reflectors made out of PMMA and mounted on MS pipe of 50mm dia duly powder coated, antirust & antitheft steel net fixed on 600mm high pole with retro reflective tapes in red or yellow in color including fixed with PCC block of required size in (1:3:6 ) type C2 using 40mm graded aggregates in foundation after excavation of required depth and size complete all as specified and directed.

Supply and fixing in repair aluminium alloy body stud/cat eye of size (110 x 120 x 23.5) mm for road surfaces complete all as specified and directed.

Supply and fixing in repair solar powered road stud (Cat eyes)of size (125x125)mmx20-25mm thick(60mm shank) of self illuminating flashing type having 3 Nos LED's for Bidirectional studs (flashing and non filtrating) visibility minimum 1000 mm flashing rate 65-75 times per min with detachable NI-MHZ battery of 1-2 V to give backup at least 3-4 days complete all as specified and directed.

Demolition of cement concrete in ground floor and paving not exc 15 cm thickness (below or above ground level) and rubbish off the premises complete all as specified and directed by Engr-In-Charge.

Dismantling of paver block/tiles of any description or thickness in floors, aprons etc. laid dry or laid dry pointing complete all as specified and directed by Engr-In-Charge.

Material and labour for 75 mm thick cement concrete 1:4:8 type D-2 (using 40 mm graded stone aggregate) as in sub base, floor complete all as specified and as directed.

Material and labour for factory made machine pressed precast concrete interlocking paver block any shape or size confirming to IS 15658 of 60mm thickness M-35 grade with grey cement and no pigment laid over and including 25mm thick sand cushioning and filling the joints upto full depth with fine tibba sand, complete all as specified and directed by Engr-In-Charge.

Fixing only retrieved machine pressed precast concrete interlocking paver block/tiles any shape or size with grey cement and no pigment laid over and including 25mm thick sand cushioning and filling the joints upto full depth with fine tibba sand, complete all as specified and directed by Engr-In-Charge.

Demolition of brickwork built in cement mortar including all quoins, arches, pillars, etc, and rubbish off the premises complete all as specified and directed.

Material and labour for Bricks work with sub class 'B' bricks straight or curved on plan mean radius built in cement mortar 1:6 complete all as specified and directed.

Material and labour for rendering 10mm thick on brick work or concrete surfaces in cement mortar 1:4 complete all as specified and directed.

Material and labour for preparation of newly plastered surface of wall and applying two coats of camouflage paint of any description over and including one coat of primer complete all as specified and directed.

Material and labour for providing, cement concrete type B-0, 1:2:4, using 12.50 mm graded stone aggregate as in roof kerbs or mud stops, rounded or chamfered on edge smooth without using extra cement complete all as specified and directed.

Ram Parkash Constructions Pvt. Ltd. (BID ID -3129163)