INSTALLATION OF SS RAILING AND OTHER ALLIED WORKS AT INDOOR HALL DODA

Earth work in surface excavation not exceeding 30 cm in depth but exceeding 1.5 m in width as well as10 sqm on plan including disposal of excavated earth, leadupto50 meter and lift upto 1.5m, as directed by Engineer-in-Charge. All kinds of soil

Earthwork in excavation by manual means in trenches for foundation,drains, pipes,cables etc(not exceeding 1.5 mt in width)and for shafts,wells cesspits and the like not exceeding 10sqm on plan depth up to 1.5mt including disposal of excavated earth up to 1 mt from cutting edge disposed earth to be levelled and neatly dressed in. All kind of soil.

Earth work in bulk excavation by mechanical means (hydraulic excavator) over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 m2 on plan) including disposal of excavated earth lead upto 50 meters and lift upto 1.5 m, as directed by Engineer-in-Charge. All kinds of soil :

Earth work in excavation by mechanical means (hydraulic excavator) in trenches for foundations, drains, pipes, cables etc. (not exceeding 1.5 m in width) and for shafts, wells, cesspits and the like not exceeding 10 sqm on plan, including dressing of sides and ramming of bottoms lift upto 1.5 m, including getting out excavated earth and disposal of surplus excavated earth as directed, within a lead of 50 metres:

Providing and laying in position cement concrete of specified grade including curing butexcluding the cost of centring and shuttering. All work upto plinth level with 1:4:8 (1 cement : 4coarse sand : 8graded stone aggregate 40 mm nominal size)complete job.

Providing and laying in position specified grade of reinforced cement concrete including curing but excluding the cost of centering, shuttering, finishing and reinforcement. All works upto plinth level 1:1½:3 (1 cement : 1½ coarse sand : 3 graded stone aggregate 20 mm nominal size)

Providing and laying in position cement concrete of specified grade including curing but excluding the cost of centring and shuttering. All work upto plinth level with: 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size)

40mm thick marble chips flooring rubbed, under layer 28mm thick cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 12.5mm nominal size) and top layer 12mm thick with white, black, chocolate, grey, yellow or green marble chips of sizes from 7 mm to 10mm nominal size, laid in cement marble powder mix 3:1 (3 cement : 1 marble powder) by weight in proportion of 2:3 (2 cement marble powder mix :3 marble chips) by volume including cement slurry and curing complete : Ordinary cement without any pigment.

Providing and fixing precoated galvanized iron profile sheets (size, shape and pitch of corrugation as approved by Engineer-in-charge) 0.50 mm (+0.05 %) total coated thickness with zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length upto 12 metre or as desired by Engineer-in-charge. The sheet shall be fixed using self drilling /self tapping screws of size (5.5x 55 mm) with EPDM seal, complete upto any pitch in horizontal/ vertical or curved surfaces, excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required.

Brick work with common burnt clay (non-modular) bricks of class designation 7.5 in foundation and plinth including curing in : Cement mortar 1:6 ( 1 cement : 6 coarse sand)

Half brick masonry with common burnt clay (non-modular) bricks of class designation 7.5 in foundations and plinth including curing in :Cement mortar 1:4 ( 1 cement : 4 coarse sand)

Centering and shuttering including strutting , propping etc. and removal of form work for Foundations , footings bases of columns etc. for mass concrete

Centering and shuttering including strutting, propping etc. and removal of form for: Lintel, beams, plinth beams, girders, bressumers and cantilevers.

FORM WORK Edges of slabs and breaks in floors and walls Under 20 cm wide

Centering and shuttering including strutting, propping etc. and removal of form for: FORM WORK Suspended floors, roofs, landings, balconies and access platforms.

Centering and shuttering including strutting, propping etc. and removal of form work for: Foundations, footings, bases for columns

12mm Cement plaster finished with a floating coat of neat cement of mix: 1 : 4 ( 1 cement : 4 fine sand)

Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level Thermo-Mechanically Treated bars of grade Fe-500D or more

Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting , hoisting , fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete. Hot finished welded type tubes

Removing white or colour wash by scrapping and sand papering and preparing the surface smooth including necessary repairs to scratches etc. complete

Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS:15622 of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 (1cement :4 coarse sand) including grouting the joints with white cement and matching pigments etc. complete Size of tile 600x600 mm

Wall painting with plastic emulsion paint of approved brand and manufacture to give an even shade, one or more coats on old work.

Structural steel work in built up sections, trusses and framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete. Welded

Providing and fixing stainless steel (Grade 304) railing made of Hollow tubes channels, plates etc. including welding ,grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete ,including fixing the railing with necessary accessories and stainless steel dash fasteners, stainless steel bolts etc. of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-in-charge, (for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasteners etc.).

Dismantling tile work in floors and roofs laid in cement mortar including stacking material within 50 meters lead. For thickness of tiles 10 mm to 25 mm

Providing and fixing gang saw cut, mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations, of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including ubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels Granite of any colour or shade (Area of slab over 0.5 sqm)

Providing and fixing in position collapsible steel shutters with vertical channels 20x10x2mm and braced with flat iron diagonals 20x5 mm size, with top and bottom rail of T-iron 40x40x6mm, with 40mm dia, steel pulleys, complete with bolts, nuts, locking arrangement, stoppers, handles, including applying a priming coat of approved steel primer

Providing and laying factory made chamfered edge Cement Concrete paver blocks in footpath, parks, lawns, drive ways or light traffic parking etc, of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over 50mm thick compacted bed of sand, compacting and proper embedding/laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand complete all as per direction of Engineer-in-Charge. 80 mm thick C.C. paver block of M-30 grade with approved color design and pattern

Providing and laying in position cement concrete of specified grade including curing but excluding the cost of centring and shuttering. All work upto plinth level with: 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size)

Painting with synthetic enamel paint of approved brand and manufacture to give an even shade. Two or more coats on new work

Supply and installation of bowling machine with 3 wheel gripping mechanism having features like differential bounce simulation , Swing and Spin variations, speed controll of 60 to 160 km/hr, auto play option campatible with 12 volt battery with tripod stand with wheels along with battery and 3 dozen of Bowling Machine Balls are made of proprietary PU material. Leverage Yantra e3 model.

Providing and fixing UV stabilized fiberglass reinforced plastic sheet roofing upto any pitch including fixing with polymer coated ‘J’ or ‘L’ hooks, bolts and nuts 8mm dia. G.I plain/ bitumen washers complete but excluding the cost of purlins, rafters, trusses etc. The sheets shall be manufactured out of 2400 TEX panel rovigs incorporating minimum 0.3% Ultra-violet stabilizer in resin system under approximately 2400 psi and hot cured. They shall be of uniform pigmentation and thickness without air pockets and shall conform to IS: 10192 and IS: 12866. The sheets shall be opaque or translucent, clear or pigmented, textured or smooth as specified. 2mm thick flat

Supply and fixing of HDPE Spectators chairs with following chairs with following specification:- 1) seat dimension = 415mm x 450mmx700mm (from ground ) with minimum 3mm and maximum 8mm wall thickness all over the profile . 2) seat shell should be blow moulded high polyethylene with uv protection dual wall with air gaps gives comfort and softness while seating on the seat with molded insert M6 threaded nut to mount on the stand & water drain hole of dia 20mm. 3) Mounting beam shall consist of 2 steel pipes of OD 34 & ID 28 mm 3 mm wall thickness with hot dip galvanizing to prevent from crossion in open air running across the length of desired length of seating . 4) Mounting bracket =MS 203x40mm 3mm thickness metal embosed bracket inter locked by bolt and nut with pipe and bracket size 110x35mm with 3mm thick embosed bracket with hot dip galvanising to prevent from crossion in open air. 5) Leg type =Floor mounted aluminium die casted (ADC12) Stand of 335x240mm for strong leg support with powder coated 50micron thickness 6)Mounting dimension =CTC can be managed with the mounting brackets on pipe to mount in different sizes which gives flexibilty of mounting CTC(minimum 420mm & maximum depending as per required space between 2 seats)

Excavation in dumped stones or malba including stacking of serviceable and unserviceable material separately and disposal of unserviceable material lead upto 50 m and lift upto 1.5 m, disposed material to be neatly dressed

Providing and fixing of heavy duty net of thickness 2.5mm (mesh size 48x48 mm) to cover cricket prctice pitch on 3 sides & Top, as per direction of engineer in charge

Providing and fixing aluminum work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/appropriate Z sections and other sections of approved make conforming to IS: 733 andIS: 1285, fixed with dash fastener of required dia. and size including necessary filling up of gaps at junctions i.e, at top, bottom and sides with required EPDM rubber / neoprene gasket felt etc. Aluminum sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminum snap beading for glazing / panelling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-Charge (glazing, panelling and dash fasteners to be paid for separately.) Powder coated aluminum (minimum thickness of powder coated 50 microns)

Supply & fixing of 40mm wide PVC strips for joints

Providing and fixing 4 mm thick ACP Sheet in panelling fixed in aluminum doors, windows shutters and partition frames (aluminum/ woodedn) with C.P. brass / stainless steel screws etc. complete as per architectural drawings and directions of engineer-incharge. (RATE ANALYSIS =1290*1.18*1.35)

P/F stainless steel water cooler(80ltr capacity) with RO of make Voltas, Bluestar or equivalent having valid IS certification including pipes, electric point and 6 module with box, switch, socket,etc. for connection as per direction engineer incharge

Supplying, installation, testing and commissioning of 1.5 Ton Inverter type Split AC's (copper) (3 star) Hot/ Cold (all weather) type of minimum capacity following sizes as detailed below. Each unit must provide cooling & dehumidification, be operatable via remote control, operate at 220-240 V AC supply with latest in vogue features. Repairs made to wall whereever required. Warrantee.:- a). Warrantee shall be provided for 12 month from the date of installations. b). The compressor shall be warranted for 5 years from the date of installation.

Supplying, Installation, Testing & Commissioning of following capacity automatic voltage stabilzer copper wound wall mounted, single phase with range of 90-240 V along with wall mounting brackets & fitting. The job includes repairing the walls where necessary. Warrantee.:- 2 Years from the date of installation. 5KVA

Supplying & fixing of M.S Wall Stand duly powder coated for outdoor unit of Split AC

Supplying, fixing & commissioning of Storage Water Heater (Geyser) of following capacity along with PVC Pipes etc as required. 25ltr

Supply of 1'' flexible pipe of superior quality idle for both hot and cold condition as per direction engineer incharge of length 85-90 feet per bundle

Providing and fixing of 1 Hp pump with motor speed of 2850 RPM with Graded cast iron casing along with necessary fitting & wire complete as per direction of engineer incharge Havells or equivalent make

Supply and fixing of single phase of following rating self priming for pumping water including connections etc as required. (Copper winding) 2HP as per direction engineer incharge

Supplying and fixing of twin core aluminium cable all along the wall surface unarmoured. 16sqmm

Providing and fixing on wall face un-plasticized Rigid PVC rain water pipes conforming to IS: 13592 Type A including jointing with seal ring conforming to IS: 5382 leaving 10 mm gap for thermal expansion. (i) Single socketed pipes 75 mm diametre

Providing and fixing on wall face un-plasticized Rigid PVC rain water pipes conforming to IS: 13592 Type A including jointing with seal ring conforming to IS: 5382 leaving 10 mm gap for thermal expansion. (i) Single socketed pipes 110 mm diametre

Providing and fixing aluminum tower bolts ISI marked anodized (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade with necessary screws etc. complete : 250x10 mm

Providing and fixing aluminum handles ISI marked anodized (anodic coating not less than grade AC 10 as per IS: 1868) transparent or dyed to required colour and shade with necessary screws etc. complete 125 mm

Providing and fixing aluminum sliding door bolts ISI marked anodized (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade with nuts and screws etc. complete : 250x16 mm

Providing and fixing aluminum hanging floor door stopper, ISI marked, anodized (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade with necessary screws etc. complete : Twin rubber stopper

Providing and fixing aluminum handles ISI marked anodized (anodic coating not less than grade AC 10 as per IS: 1868) transparent or dyed to required colour and shade with necessary screws etc. complete 250 mm

Providing and fixing factory made precast RCC perforated drain covers, having concrete of strength not less than M-25, of size 1000x450x50 mm reinforced with 8 mm dia four nos longitudinal and 9nos cross sectional T.M.T hoop bars, including providing 50 mm dia perforations @ 100 to 125 mm c/c, including providing edge binding with M.S flats of size 50mmx1.6mm complete all as per direction of Engineer-in-charge.

Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required. 2 X 4 sq. mm + 1 X 4 sq. mm earth wire

Supplying and fixing of following sizes of PVC conduit along with accessories in surface/ recess including cutting the wall and making good the same in case of recessed conduit as required. (ISI Make). 25mm

Provision for supply and Installation of Pedestal for Inaguration made of MS Frame 40 x 40 x 2.6 mm with 4 mm thick ACP Sheet as base of size 4' x 6' and Acrylic Inaguration Plate Acrylic sheet cover as per direction of Engineer Incharge

P/F wall fan of havells make or eqvt make including testing commissioning complete

Supply Installation of exhaust fan in the existing opening, including making good the damage, connection, testing, commissioning etc. as required. Exhaust fan 300mm

CARRIAGE OF MATERIALS By Mechanical Transport including loading, unloading and stacking 20Km stone aggregate 20 Km by MT

CARRIAGE OF MATERIALS By Mechanical Transport including loading, unloading and stacking 20Km Sand, aggregate 20 Km by MT

Brick

Please Enable Macros to View BoQ information