Set of Tools required for Tool box.

The tenderer with past performance of satisfactory execution of contracts to SC Railway, or Other Zonal Railways/Pus for supply of the same / similar items (Like Tool Box (Empty), Spanner Set, Open End Spanner, Ring Spanner, Combination Spanner, Adjustable Spanner, Socket Set, Socket Wrench, Ratchet Handle, Extension Bar, Universal Joint, Allen Key Set, Hex Key Set, Screw Driver Set, Flat Screw Driver, Phillips Screw Driver, Offset Screw Driver, Torque Wrench, Pipe Wrench, Chain Wrench, Monkey Spanner, Double End Spanner, Box Spanner Set, Tommy Bar, Combination Pliers, Long Nose Pliers, Side Cutting Pliers, Circlip Pliers, Locking Pliers, Water Pump Pliers, Slip Joint Pliers, Ball Peen Hammer, Cross Peen Hammer, Club Hammer, Soft Face Hammer, Rubber Mallet, Cold Chisel Set, Flat Chisel, Cape Chisel, Centre Punch, Pin Punch Set, Drift Punch, Taper Punch, Flat File, Half Round File, Round File, Triangular File, Square File, Hand Hacksaw Frame, Hacksaw Blades, Feeler Gauge Set, Thread Pitch Gauge, Steel Rule, Measuring Tape, Try Square, Combination Square, Inside Caliper, Outside Caliper, Divider, Scriber, Vernier Caliper, Outside Micrometer, Depth Gauge, Straight Edge, Spirit Level, Wire Brush, Scraper, Bearing Puller, Gear Puller, Oil Can, Grease Gun, Hand Drill, Tap and Die Set, Tap Wrench, Die Stock, Reamer Set, Deburring Tool, Gasket Scraper, Seal Puller, Valve Lapping Tool, Wheel Gauge Tool, Track Gauge Tool, Brake Adjusting Spanner, Wheel Spanner, Axle Box Spanner, Coupler Maintenance Tool Kit, Brake Cylinder Tool Kit, Bearing Fitting Tool, Bearing Removal Tool, Pin Extractor, Alignment Punch, Drift Key, Socket Adapter, T-Handle Hex Key, T-Handle Wrench, Valve Spanner, Fuse Puller Tool, Cable Cutter, Crimping Tool, Wire Stripper, Terminal Crimping Pliers, Hand Riveter, Hand Vice, Bench Vice, C-Clamp, G-Clamp, Tool Roll, Portable Metal Tool Chest, Maintenance Tool Cabinet, Workshop Tool Kit, Fitter Tool Kit, Mechanical Maintenance Tool Kit, Coach Repair Tool Kit, Wagon Repair Tool Kit, Loco Shed Tool Kit, Permanent Way Tool Kit, Bridge Inspection Tool Kit, OHE Maintenance Tool Kit, Signal & Telecom Tool Kit, Emergency Breakdown Tool Kit, Portable Emergency Repair Tool Kit..) for a quantity of 20 percent or more of tendered quantity against a single contract during last three years prior to, and excluding tender opening date may be considered as responsive to SC Railways requirements for placement of bulk and regular order. Tenderers are requested to submit the past performance report such as Copies of R Notes/CRAC/Proof of acceptance of material by consignee etc. along with their offer; failing which offer will be summarily rejected without making any back reference. However, in cases where the tenderers are having satisfactory past supply performances of tendered items for stock items with IR, the supply performance data available in iMMIS with IR shall be taken into consideration while evaluating the offers of the tenderers

If such past performance level is lower, then the offer may be considered as responsive to SC Railways requirements for placement of developmental order not exceeding 20 percent of the net procurable quantity. The tenderers, who have no past performance as above, may also be considered for such developmental orders, but for consideration of such developmental orders, they shall submit details of M & P, testing facilities, STR & QAP, technical manpower available, UDYAM Registration Certificate for same/similar items etc., along with their offer

In case, the tenderer participates as an authorized dealer, then the performance as required above shall be that of Principal (OEM) authorizing the agent or bidder for the same OEM. It may so happen that the agent/dealer has credentials of past supply for a different Principal/OEM, then it will not be considered as performance. In case, the tenderer is authorized agent, tenderer shall submit the tender specific authorization. In case, the dealer/distributor of the OEM of the acceptable make, tenderer should upload the current authorization/dealership certificate issued by the OEM

For detailed instructions refer, GENERAL TENDER CONDITIONS attached with NIT and/or available as Public Document on IREPS website Goods and Services/South Central Railway.

Have you submitted a Bid security declaration as per Tender conditions

Have you furnished authorization/dealership certificate issued by OEM as specific authorization? (if manufacturer is not quoting directly)

Have you furnished a performance statement?

Have you furnished the statement of Deviations? (preferably 'NIL')

Have you indicated the complete name and address of the agents and details of the services to be rendered by the agents?

Have you submitted relevant/ valid documents as per Eligibility Criteria?

Have you read instructions to tenderers, General conditions of contract, IRS conditions of contract attached with the tender?

If you are not a MSE or a consortia of MSEs formed by NSIC, please indicate percentage of sub contracts in execution of this tender that will be from Micro and Small Enterprise (in percent of order value) with further breakup of MSE owned by SC/ST. (Information will be provided in % terms with 6 fileds; Micro owned by SC, Micro owned by ST, Micro owned by Others, Small industry owned by SC, Small industry owned by ST, Small industry owned by Others.

Have you attached any performance statement separately

Tenderers must acknowledge acceptance of IRS conditions of contract

Have you attached any commercial deviation

Have you attached any Technical deviation

Tenderer should enclose latest technical literature/catalogue duly highlighting the model no/catalogue no/product code offered TP assess suitability

Restrictions under Rule 144 (xi) of GFRs-2017: a) I have read the clause regarding Restrictions under Rule 144(xi) of GFRs-2017 on procurement from a bidder of a country which shares a land border with India and as detailed in Tender Documents. b) I certify that this bidder is not from such a country or, if from such a country, has been registered with the Competent Authority. c) I hereby certify that this bidder fulfills all requirements in this regard and is eligible to be considered. (Wherever applicable, evidence of valid registration by the competent authority shall be attached). Note: If the tenderers are not agreeable to above declaration, they have to categorically mention about the disagreement in Techno Commercial Deviation.

Have you submitted relevant/ valid documents as per Eligibility Criteria?

Please enter the percentage of local content in the material being offered. Please enter 0 for fully imported items, and 100 for fully indigenous items. The definition and calculation of local content shall be in accordance with the Make in India policy as incorporated in the tender conditions.

Please enter the percentage of local content in the material being offered. Please enter 0 for fully imported items, and 100 for fully indigenous items. The definition and calculation of local content shall be in accordance with the Make in India policy as incorporated in the tender conditions.