WBPWD/SE/SWEC/NIQ16/2025-26

Amount

PART-A [GIRLS HOSTEL]

LT Panel Supply & delivery of cubical type L.T. Distribution panel board of required size wall cum floor mounted compartmentalized with maple arrangement having rigid & self supporting structure fabricated from 2 mm thick CRCA sheet steel with M/S angle frame. The panel board consisting of the following switches & the Panel board to be get inspected by EIC -- A) Incoming Arrangement. a) switch disconnect or fuse (panel mounting cubical type) conform to IS : 13947 in open execution three pole & Neutral AC 23A, 50HZ, 415 Volt 250 Amp with 3 nos 250Amp DIN type HBC fuse link , (Make- L&T/ABB/ Havells/Siemens/ as per direction of EIC) . . --1 No B)Bus Section: 415 V, 400A. electrolyte grade tinned copper bus bar with vertical section of required size same in size for Phase RYB, & neutral bars & 20x 5 mm Al. Bar for earth. A bus bar shall be fixed with FRP chair & the entire bars are insulated with PVC heat Sinkable sleeve of suitable size & color as per direction of E.I.C C) Outgoing arrangement: a) switch disconnect or fuse (panel mounting cubical type) conform to IS : 13947 in open execution three pole & Neutral AC 23A, 50HZ, 415 Volt 125 Amp with 3 nos 125 Amp DIN type HBC fuse link , (Make- L&T/ABB/ Havells/Siemens/ as per direction of EIC) . . --2 Nos. b) Switch disconnector fuse (panel mounting cubical type) conform to IS: 13947 in open execution three pole & Neutral AC 23A, 50HZ, 415 Volt 63 Amp with 3 nos 63 Amp DIN type HBC fuse link, (Make- L&T/ABB/ Havells/Siemens/ as per direction of EIC) . ---- 3 Nos. c) Switch disconnector fuse (panel mounting cubical type) conform to IS: 13947 in open execution three pole & Neutral AC 23A, 50HZ, 415 Volt 32 Amp with 3 nos 32 Amp DIN type HBC fuse link, (Make- L&T/ABB/ Havells/Siemens/ as per direction of EIC) . ---- 1 Nos.

Distn. Wiring in 1.1 KV grade 2x22/0.3 (1.5 sqmm) single core stranded 'FR' PVC insulated & unsheathed copper wire (Make- R R Kabel/ Polycab/ Finolex/ KEI/ Gloster/ as per direction of EIC) in 19mm bore, 3mm thick polythene pipe complete with all accessories embedded in wall to light / Fan / Call bell point as per GS with with Modular type switch (Legrand-Model Arteror/Myrius or equivalent model of Crabtree/Equivalent make as per direction of E.I.C) following average run.

Distn. wiring in 3 X 22/0.3 (1.5 sqmm) single core stranded 'FR' PVC insulated & unsheathed single core stranded copper wire (Make- R R Kabel/ Polycab/ Finolex/ KEI/ Gloster/ as per direction of EIC) in 19 mm bore, 3 mm thick polythen pipe complete with all accessories embedded in wall to 240 V 6A 5 pin plug point with MODULAR type switch(Make- Legrand, Model- Myrius or equivalent model of Crabtree/ Equivalent make as per direction of E.I.C) as per GS.

On Board

Supplying & Fixing sheet metal inspection box (16 SWG) of the following sizes(in mm ) flushed in wall as per GS

Supplying and Drawing 1.1 KV single core stranded 'FR' PVC insulated & unsheathed single core stranded copper wire(Make- R R Kabel/ Polycab/ Finolex/ KEI/ Gloster/ as per direction of EIC) of the following sizes in the 19mm/25mm prelaid polythene pipe/PVC rigid conduit as per GS.

3 x (1.5 sqmm)

2x(2.5 sqmm)+1x(1.5 sqmm)

Supplying and fixing 240/415 V MCB of Breaking capacity 10kA & C characteristics on din rail of new/ existing DBs and necessary connectionas per GS (LEGRAND/ABB/L&T/Siemens)

Supplying and fixing 415V, TPN SFU with sheet steel enclosure on angle iron frame on wall with nuts bolts etc incl. S & F 3 nos. DIN type HRC fuse as per rating. (L&T/Siemens/Havells/Standard)

Supplying & Fixing modular type socket /socket (Make- Legrand/ Havells/ L&T/ Goldmedal/ as per direction of EIC) in exsisting Modular board incl. connections.

6 A 5-pin modular type 5 pin socket

6 A modular type switch

Supply & Fixing 240 V, 1 nos. 16A & 3 nos. 6 A, 3 pin Modular type plug socket with 1 nos. 16A & 3 nos. 6 A Modular type switch (Make- Legrand/ Havells/ L&T/ Goldmedal/ as per direction of EIC), 16A Modular switch type MCB (C-Curve) and Indicator without plug top on 2 row 18 Module GI Modular type switch board with 2 row 18 Module top cover plate flushed in wall incl. S&F switch board and cover plate and making necy.connections with PVC Cu wire and earth continuity wire etc.

Supply and delivery of single/twin Industrial LED Batten luminaries incl. Supply of 1 no./2nos. 18W LED Tube

Single Fittings (make- Crompton, Model ECO-I, Cat No. IGP161LT8-16 1xT8 or equivalent model of Benlo/ Surya as per direction of EIC, incl. 1 no. LED Aluminium T8 tube Make: Crompton Model- CRYSTA, Cat No. LTT8-20 or equivalent model of Benlo/ Surya as per direction of EIC

Fixing only single/twin LED batten light fitting suspended from the ceiling fixed with “L” type MS clamp for RC ceiling / MS pipe as per GS direction of EIC

Fixing only single/twin LED Batten light fitting complete with all accessories Directly on wall/ceiling as per GS

Supply & Fixing angular batten holder (Anchor) on 75mm dia PVCround block / round bakelite on wall/ceiling as per GS.

Supply and fixing LED Inverter bulb of 12 W (Philips/Benlo /Surya) on existing batten holder

Supply & delivary of AC 240V 50 Hz 48" sweep (1200 mm) ceiling fan complete with down rod , Canopy, fork incl S & F of P - 2 type capacitor as per IS specification & proper Manufacturer certificate of the capacitor (supplied at the time of delivered the fans ) etc. with out regulator, (Make- Usha Striker equivalent model of Crompton Greaves/ Orient New Breeze/Usha/as per direction of EIC)

Fixing only ceiling fan complete with blades, canopy, fork, rubber bush etc. incl. S&F connecting wire for down rod upto 30 cm incl. painting the rod with approved paint and making necessary connection as required by 2x1.5 sqmm flexible copper wire .

Supply & fixing 300 mm Heavy Duty Exh. (920 RPM) Grey Exhaust fan of followinng sizes after making hole in wall and making good the damages and smooth cement finish etc. as practicable as possible and providing necy. length of PVC insulated wire and making connection for exhaust as per direction of E.I.C. [Make: EPC/ Usha/ Orient/ CG/ as per direction of EIC] 12"( 300mm ) Speed 920 RPM [NS]

Supply & Fixing GI sheet (20SWG) metal Cowl with MS flat iron frame & GI wire mesh on wall as per GS (12")

Supply & Fixing 240V, Modular Step type fan regulator (Step type) on existing switch board with top cover plate incl. making necy. connections etc.

Extra for supplying additional wire for down rod & painting the rod exceeding 30 cm by 2x1.5 sqmm flexible copper wire as per GS.

Earthing with 50 mm dia GI pipe 3.64 mm thick x 3.04 Mts. long and 1 x 4 SWG GI (Hot Dip) wire (4 Mts. long), 13 mm dia x 80 mm long GI bolts, double nuts, double washers incl. S & F 15 mm dia GI pipe protection (1 Mts. long) to be filled with bitumen partly under the ground level and partly above ground level driven to an average depth of 3.65 Mts. below the ground level by ISI Medium

Excavation of soil for installation of Earth Electrode and filling & ramming. (For Soft Soil)

Connecting the pole to earth Electrode including S & F Solid GI (Hot Dip) wire of size as below as per GS No.-10 SWG

Supplying & fixing earth busbar of galvanized (Hot Dip) MS flat 25 mm x 6 mm on wall as per GS

Supply and installation by OEM or Authorized channel Partner of OEM, of external, wide area, early steamer emission OPR 30 type lightning arrester made of robust stainless steel & tested Standard stated in French Standard NF C17- 102, and IEC 62305-2. It is capable of polarizing the tip with a voltage of 600V to 10-20kV/m synchronized with an approaching lightning and triggering a powerful upward streamer with speed of 1m/µs into the air, with average time gain of 25 microseconds earlier than naturally formed streamers. Its upward streamers are strong enough to withstand applicable cyclonic wind speeds.The serial number displayed on the ESE lightning arrester shall be duly supported with the "certificate of country of origin" issued indicating the serial number of the product supplied. The ESE terminal must offer protection radius of 48 Mtrs. in Protection Level - I (high protection) and preferably to be mounted on the roof top of the building. ( Make: ABB)

Supply and installation by OEM or Authorized channel Partner of OEM of stainless steel support Mounting Mast 30 mm dia to hold early steamer emission OPR 30, of robust design with guy wire and base plate alongwith all accessories like clamps, shaddles, holding arrangements to fix mast to building structure at highest point such that the air terminal is 5 mtrs above the tallest structure Mounting Mast. (2 Mtrs. and 3 Mtrs. with Guy wire and Base Plate)

Supply and installation of lightning Stroke Counter by OEM or Authorized channel Partner of OEM working electro mechanically without any power supply.The recorder shall be of non-resettable type with the electro-mechanical display. No LCD screen is permittted as it may depend upon the battery life to energize the LCD. The lightning stroke recorder shall be duly tested & certified inline with the ESE lightning arrseter in an international labortaory for an impulse current (8/20 micro sec) and should count lightning strokes of 0.4 Ka to 150 Ka. ( Make ABB )

Supply and Laying of Down Conductor G.I.Strip of 40/6 mm ( length - As per Actual), both Verticle and Horizontal, clamping by saddles not exceeding 500 mm apart with 35/8" screw for fixing in wall complete with full threaded bolts with nuts and double washers incl. mending good damages to building work. Finishing the ends of the above Strip by Nut and Bolts, etc.

Hiring charges for Scaffolding arrangement including dismantling at the end of work and carriage, for ESE OPR 30 LA installation.

Supply and Installation by OEM or Authorized channel Partner of OEM of Medium Pipe (10 ft. long, 2" dia G.I.Pipe along with earth rod and Chemical Gel filled with highly conducting metallic compounds with permenant sealings at both ends - ( Make Standard, ISI Brand )for Earthing and for inter connection of Earthing under ground (of 3 meters X 1nos. per pit) with 3 Earth pits of 10 feet deep each.

Supply and Laying of maintenance free earthing terminal which consist of Ground Resistance Improving Furse Cem Conductive Aggregate material, tested as per BS. 1 bag of 25 kg. per Pit, to make it maintenance free and provide low resistance in the earth terminal to be executed by OEM or Authorized channel Partner of OEM only.

Supply of 4/3.5 Core XLPE Insulated & Sheathed Armoured Aluminium Conductor cables for Working Voltage up to 1100 Volts of following sizes [ Make : RR Kabel / Polycab / Havells / Gloster/KEI ]

4 Core 16 Sq. mm ( for girls hostel to staff quarter)

4 Core 70 Sq. mm ( for Main Feederpillar)

Laying of one No. cable above 35 sqmm and upto 185 sqmm in underground trench 460mm wide x 760mm average depth, with brick protection on the top of the cable with 8 (eight) Nos. bricks per Mtr. including filling the space between the bricks and cable and also the trenchwith shifted soil, leveling up and restoring surface duly rammed

Laying of one No. cable upto 35 sqmm in underground trench 460 mm wide x 760 mm average depth, with brick protection on the top of the cable with 8 (eight) Nos. bricks per metre, including filling the space between the brick & cable and also the trench with shifted soil, leveling up and restoring surface duly rammed

Laying on Pole with Clamps Fixing of Cable along the length of O.H. pole incl. S & F MS pole clamps fabricated from 25 mm x 6 mm MS flat incl. painting

Supply of MS/GI pole and fixing with suitable concrete foundation of 1:1.5:3 concrete mixture

Supplying and fixing compression type gland and finishing those for following XLPE / PVC armoured cable (2/4 / 3.5)Core as per GS.

4 Core 16 Sq. mm

4 Core 70 Sq. mm

PART-B [BOYS HOSTEL]

Inter Connection: All interconnection of switches & bus bar Shall be made with required sizes of multi strand PVC insulated copper wire to be kept for Cable connection for main switches & the end of all connections of metering panel to be finish with Copper socket by crimping method having Marked ferrule for indication. Earthing. A separate earth bolts/Bars – 2 Nos will be provided in panel board in both sides as per drawing. Cable Alley: Cable entry arrangement will be provided in the cubical panel in vertical position of size with reqd sizes of AC/DC make connector indicating phase & neutral for each outgoing main switches & gland plate must be placed at the bottom of the panel with detachable type as per direction of E.I.C. Painting. The complete panel board shall be painted by 2 coats of powder coated synthetic enamel Paint over two coats of R.O. primer of Approved make & brand & color as per Direction of E.I.C. Constructural Details: All incoming & outgoing panel mounted cubical Switch disconnector fuse shall be housed in Respective compartment with hinged & gasketted Door at front. All doors shall have Panel lock Arrangement. The panel shall be properly Gasketted to prevent ingress of dust & moisture & Remaining . Busbar will be properly arrange & all Switches shall be fixed by M.S. nuts

Distn. Wiring in 1.1 KV grade 2x22/0.3 (1.5 sqmm) single core stranded 'FR' PVC insulated & unsheathed copper wire (Make- R R Kabel/ Polycab/ Finolex/ KEI/ Gloster/ as per direction of EIC) in 19mm bore, 3mm thick polythene pipe complete with all accessories embedded in wall to light / Fan / Call bell point as per GS with with Modular type switch (Legrand-Model Arteror/Myrius or equivalent model of Crabtree/Equivalent make as per direction of E.I.C) following average run.

Distn. wiring in 3 X 22/0.3 (1.5 sqmm) single core stranded 'FR' PVC insulated & unsheathed single core stranded copper wire (Make- R R Kabel/ Polycab/ Finolex/ KEI/ Gloster/ as per direction of EIC) in 19 mm bore, 3 mm thick polythen pipe complete with all accessories embedded in wall to 240 V 6A 5 pin plug point with MODULAR type switch(Make- Legrand, Model- Myrius or equivalent model of Crabtree/ Equivalent make as per direction of E.I.C) as per GS.

On Board

Supplying & Fixing sheet metal inspection box (16 SWG) of the following sizes(in mm ) flushed in wall as per GS

Supplying and Drawing 1.1 KV single core stranded 'FR' PVC insulated & unsheathed single core stranded copper wire(Make- R R Kabel/ Polycab/ Finolex/ KEI/ Gloster/ as per direction of EIC) of the following sizes in the 19mm/25mm prelaid polythene pipe/PVC rigid conduit as per GS.

3 x (1.5 sqmm)

2x(2.5 sqmm)+1x(1.5 sqmm)

Supplying and fixing 240/415 V MCB of Breaking capacity 10kA & C characteristics on din rail of new/ existing DBs and necessary connectionas per GS (LEGRAND/ABB/L&T/Siemens)

Supplying and fixing 415V, TPN SFU with sheet steel enclosure on angle iron frame on wall with nuts bolts etc incl. S & F 3 nos. DIN type HRC fuse as per rating. (L&T/Siemens/Havells/Standard)

Supplying & Fixing modular type socket /socket (Make- Legrand/ Havells/ L&T/ Goldmedal/ as per direction of EIC) in exsisting Modular board incl. connections.

6 A 5-pin modular type 5 pin socket

6 A modular type switch

Supply & Fixing 240 V, 1 nos. 16A & 3 nos. 6 A, 3 pin Modular type plug socket with 1 nos. 16A & 3 nos. 6 A Modular type switch (Make- Legrand/ Havells/ L&T/ Goldmedal/ as per direction of EIC), 16A Modular switch type MCB (C-Curve) and Indicator without plug top on 2 row 18 Module GI Modular type switch board with 2 row 18 Module top cover plate flushed in wall incl. S&F switch board and cover plate and making necy.connections with PVC Cu wire and earth continuity wire etc.

Supply and delivery of single/twin Industrial LED Batten luminaries incl. Supply of 1 no./2nos. 18W LED Tube

Single Fittings (make- Crompton, Model ECO-I, Cat No. IGP161LT8-16 1xT8 or equivalent model of Benlo/ Surya as per direction of EIC, incl. 1 no. LED Aluminium T8 tube Make: Crompton Model- CRYSTA, Cat No. LTT8-20 or equivalent model of Benlo/ Surya as per direction of EIC

Fixing only single/twin LED batten light fitting suspended from the ceiling fixed with “L” type MS clamp for RC ceiling / MS pipe as per GS direction of EIC

Fixing only single/twin LED Batten light fitting complete with all accessories Directly on wall/ceiling as per GS

Supply & Fixing angular batten holder (Anchor) on 75mm dia PVCround block / round bakelite on wall/ceiling as per GS.

Supply and fixing LED Inverter bulb of 12 W (Philips/Benlo /Surya) on existing batten holder

Supply & delivary of AC 240V 50 Hz 48" sweep (1200 mm) ceiling fan complete with down rod , Canopy, fork incl S & F of P - 2 type capacitor as per IS specification & proper Manufacturer certificate of the capacitor (supplied at the time of delivered the fans ) etc. with out regulator, (Make- Usha Striker equivalent model of Crompton Greaves/ Orient New Breeze/Usha/as per direction of EIC)

Fixing only ceiling fan complete with blades, canopy, fork, rubber bush etc. incl. S&F connecting wire for down rod upto 30 cm incl. painting the rod with approved paint and making necessary connection as required by 2x1.5 sqmm flexible copper wire .

Supply & fixing 300 mm Heavy Duty Exh. (920 RPM) Grey Exhaust fan of followinng sizes after making hole in wall and making good the damages and smooth cement finish etc. as practicable as possible and providing necy. length of PVC insulated wire and making connection for exhaust as per direction of E.I.C. [Make: EPC/ Usha/ Orient/ CG/ as per direction of EIC] 12"( 300mm ) Speed 920 RPM [NS]

Supply & Fixing GI sheet (20SWG) metal Cowl with MS flat iron frame & GI wire mesh on wall as per GS (12")

Supply & Fixing 240V, Modular Step type fan regulator (Step type) on existing switch board with top cover plate incl. making necy. connections etc.

Extra for supplying additional wire for down rod & painting the rod exceeding 30 cm by 2x1.5 sqmm flexible copper wire as per GS.

Earthing with 50 mm dia GI pipe 3.64 mm thick x 3.04 Mts. long and 1 x 4 SWG GI (Hot Dip) wire (4 Mts. long), 13 mm dia x 80 mm long GI bolts, double nuts, double washers incl. S & F 15 mm dia GI pipe protection (1 Mts. long) to be filled with bitumen partly under the ground level and partly above ground level driven to an average depth of 3.65 Mts. below the ground level by ISI Medium

Excavation of soil for installation of Earth Electrode and filling & ramming. (For Soft Soil)

Connecting the pole to earth Electrode including S & F Solid GI (Hot Dip) wire of size as below as per GS No.-10 SWG

Supplying & fixing earth busbar of galvanized (Hot Dip) MS flat 25 mm x 6 mm on wall as per GS

Supply and installation by OEM or Authorized channel Partner of OEM, of external, wide area, early steamer emission OPR 30 type lightning arrester made of robust stainless steel & tested Standard stated in French Standard NF C17- 102, and IEC 62305-2. It is capable of polarizing the tip with a voltage of 600V to 10-20kV/m synchronized with an approaching lightning and triggering a powerful upward streamer with speed of 1m/µs into the air, with average time gain of 25 microseconds earlier than naturally formed streamers. Its upward streamers are strong enough to withstand applicable cyclonic wind speeds.The serial number displayed on the ESE lightning arrester shall be duly supported with the "certificate of country of origin" issued indicating the serial number of the product supplied. The ESE terminal must offer protection radius of 48 Mtrs. in Protection Level - I (high protection) and preferably to be mounted on the roof top of the building. ( Make: ABB)

Supply and installation by OEM or Authorized channel Partner of OEM of stainless steel support Mounting Mast 30 mm dia to hold early steamer emission OPR 30, of robust design with guy wire and base plate alongwith all accessories like clamps, shaddles, holding arrangements to fix mast to building structure at highest point such that the air terminal is 5 mtrs above the tallest structure Mounting Mast. (2 Mtrs. and 3 Mtrs. with Guy wire and Base Plate)

Supply and installation of lightning Stroke Counter by OEM or Authorized channel Partner of OEM working electro mechanically without any power supply.The recorder shall be of non-resettable type with the electro-mechanical display. No LCD screen is permittted as it may depend upon the battery life to energize the LCD. The lightning stroke recorder shall be duly tested & certified inline with the ESE lightning arrseter in an international labortaory for an impulse current (8/20 micro sec) and should count lightning strokes of 0.4 Ka to 150 Ka. ( Make ABB )

Supply and Laying of Down Conductor G.I.Strip of 40/6 mm ( length - As per Actual), both Verticle and Horizontal, clamping by saddles not exceeding 500 mm apart with 35/8" screw for fixing in wall complete with full threaded bolts with nuts and double washers incl. mending good damages to building work. Finishing the ends of the above Strip by Nut and Bolts, etc.

Hiring charges for Scaffolding arrangement including dismantling at the end of work and carriage, for ESE OPR 30 LA installation.

Supply and Installation by OEM or Authorized channel Partner of OEM of Medium Pipe (10 ft. long, 2" dia G.I.Pipe along with earth rod and Chemical Gel filled with highly conducting metallic compounds with permenant sealings at both ends - ( Make Standard, ISI Brand )for Earthing and for inter connection of Earthing under ground (of 3 meters X 1nos. per pit) with 3 Earth pits of 10 feet deep each.

Supply and Laying of maintenance free earthing terminal which consist of Ground Resistance Improving Furse Cem Conductive Aggregate material, tested as per BS. 1 bag of 25 kg. per Pit, to make it maintenance free and provide low resistance in the earth terminal to be executed by OEM or Authorized channel Partner of OEM only.

Supply of 4/3.5 Core XLPE Insulated & Sheathed Armoured Aluminium Conductor cables for Working Voltage up to 1100 Volts of following sizes [ Make : RR Kabel / Polycab / Havells / Gloster/KEI ]

4 Core 70 Sq. mm ( for Main panel to boys hostel)

Laying of one No. cable above 35 sqmm and upto 185 sqmm in underground trench 460mm wide x 760mm average depth, with brick protection on the top of the cable with 8 (eight) Nos. bricks per Mtr. including filling the space between the bricks and cable and also the trenchwith shifted soil, leveling up and restoring surface duly rammed

Supplying and fixing compression type gland and finishing those for following XLPE / PVC armoured cable (2/4 / 3.5)Core as per GS.

4 Core 70 Sq. mm

PART-C [HOSTEL CAMPUS]

Inter Connection: All interconnection of switches & bus bar Shall be made with required sizes of multi strand PVC insulated copper wire to be kept for Cable connection for main switches & the end of all connections of metering panel to be finish with Copper socket by crimping method having Marked ferrule for indication. Earthing. A separate earth bolts/Bars – 2 Nos will be provided in panel board in both sides as per drawing. Cable Alley: Cable entry arrangement will be provided in the cubical panel in vertical position of size with reqd sizes of AC/DC make connector indicating phase & neutral for each outgoing main switches & gland plate must be placed at the bottom of the panel with detachable type as per direction of E.I.C. Painting. The complete panel board shall be painted by 2 coats of powder coated synthetic enamel Paint over two coats of R.O. primer of Approved make & brand & color as per Direction of E.I.C. Constructural Details: All incoming & outgoing panel mounted cubical Switch disconnector fuse shall be housed in Respective compartment with hinged & gasketted Door at front. All doors shall have Panel lock Arrangement. The panel shall be properly Gasketted to prevent ingress of dust & moisture & Remaining . Busbar will be properly arrange & all Switches shall be fixed by M.S. nuts

Distn. Wiring in 1.1 KV grade 2x22/0.3 (1.5 sqmm) single core stranded 'FR' PVC insulated & unsheathed copper wire (Make- R R Kabel/ Polycab/ Finolex/ KEI/ Gloster/ as per direction of EIC) in 19mm bore, 3mm thick polythene pipe complete with all accessories embedded in wall to light / Fan / Call bell point as per GS with with Modular type switch (Legrand-Model Arteror/Myrius or equivalent model of Crabtree/Equivalent make as per direction of E.I.C) following average run.

Distn. wiring in 3 X 22/0.3 (1.5 sqmm) single core stranded 'FR' PVC insulated & unsheathed single core stranded copper wire (Make- R R Kabel/ Polycab/ Finolex/ KEI/ Gloster/ as per direction of EIC) in 19 mm bore, 3 mm thick polythen pipe complete with all accessories embedded in wall to 240 V 6A 5 pin plug point with MODULAR type switch(Make- Legrand, Model- Myrius or equivalent model of Crabtree/ Equivalent make as per direction of E.I.C) as per GS.

On Board

Supplying & Fixing sheet metal inspection box (16 SWG) of the following sizes(in mm ) flushed in wall as per GS

Supplying and Drawing 1.1 KV single core stranded 'FR' PVC insulated & unsheathed single core stranded copper wire(Make- R R Kabel/ Polycab/ Finolex/ KEI/ Gloster/ as per direction of EIC) of the following sizes in the 19mm/25mm prelaid polythene pipe/PVC rigid conduit as per GS.

3 x (1.5 sqmm)

2x(2.5 sqmm)+1x(1.5 sqmm)

Supplying and fixing 240/415 V MCB of Breaking capacity 10kA & C characteristics on din rail of new/ existing DBs and necessary connectionas per GS (LEGRAND/ABB/L&T/Siemens)

Supplying and fixing 415V, TPN SFU with sheet steel enclosure on angle iron frame on wall with nuts bolts etc incl. S & F 3 nos. DIN type HRC fuse as per rating. (L&T/Siemens/Havells/Standard)

Supplying & Fixing modular type socket /socket (Make- Legrand/ Havells/ L&T/ Goldmedal/ as per direction of EIC) in exsisting Modular board incl. connections.

6 A 5-pin modular type 5 pin socket

6 A modular type switch

Supply and delivery of single/twin Industrial LED Batten luminaries incl. Supply of 1 no./2nos. 18W LED Tube

Single Fittings (make- Crompton, Model ECO-I, Cat No. IGP161LT8-16 1xT8 or equivalent model of Benlo/ Surya as per direction of EIC, incl. 1 no. LED Aluminium T8 tube Make: Crompton Model- CRYSTA, Cat No. LTT8-20 or equivalent model of Benlo/ Surya as per direction of EIC

Fixing only single/twin LED batten light fitting suspended from the ceiling fixed with “L” type MS clamp for RC ceiling / MS pipe as per GS direction of EIC

Supply & Fixing angular batten holder (Anchor) on 75mm dia PVCround block / round bakelite on wall/ceiling as per GS.

Supply and fixing LED Inverter bulb of 12 W (Philips/Surya /Benlo) on existing batten holder

Supply & fixing 300 mm Heavy Duty Exh. (920 RPM) Grey Exhaust fan of followinng sizes after making hole in wall and making good the damages and smooth cement finish etc. as practicable as possible and providing necy. length of PVC insulated wire and making connection for exhaust as per direction of E.I.C. [Make: EPC/ Usha/ Orient/ CG/ as per direction of EIC] 12"( 300mm ) Speed 920 RPM [NS]

Supply & Fixing GI sheet (20SWG) metal Cowl with MS flat iron frame & GI wire mesh on wall as per GS (12")

Earthing with 50 mm dia GI pipe 3.64 mm thick x 3.04 Mts. long and 1 x 4 SWG GI (Hot Dip) wire (4 Mts. long), 13 mm dia x 80 mm long GI bolts, double nuts, double washers incl. S & F 15 mm dia GI pipe protection (1 Mts. long) to be filled with bitumen partly under the ground level and partly above ground level driven to an average depth of 3.65 Mts. below the ground level by ISI Medium

Excavation of soil for installation of Earth Electrode and filling & ramming. (For Soft Soil)

Connecting the pole to earth Electrode including S & F Solid GI (Hot Dip) wire of size as below as per GS No.-10 SWG

Supplying & fixing earth busbar of galvanized (Hot Dip) MS flat 25 mm x 6 mm on wall as per GS

Supply and installation by OEM or Authorized channel Partner of OEM, of external, wide area, early steamer emission OPR 30 type lightning arrester made of robust stainless steel & tested Standard stated in French Standard NF C17- 102, and IEC 62305-2. It is capable of polarizing the tip with a voltage of 600V to 10-20kV/m synchronized with an approaching lightning and triggering a powerful upward streamer with speed of 1m/µs into the air, with average time gain of 25 microseconds earlier than naturally formed streamers. Its upward streamers are strong enough to withstand applicable cyclonic wind speeds.The serial number displayed on the ESE lightning arrester shall be duly supported with the "certificate of country of origin" issued indicating the serial number of the product supplied. The ESE terminal must offer protection radius of 48 Mtrs. in Protection Level - I (high protection) and preferably to be mounted on the roof top of the building. ( Make: ABB)

Supply and installation by OEM or Authorized channel Partner of OEM of stainless steel support Mounting Mast 30 mm dia to hold early steamer emission OPR 30, of robust design with guy wire and base plate alongwith all accessories like clamps, shaddles, holding arrangements to fix mast to building structure at highest point such that the air terminal is 5 mtrs above the tallest structure Mounting Mast. (2 Mtrs. and 3 Mtrs. with Guy wire and Base Plate)

Supply and installation of lightning Stroke Counter by OEM or Authorized channel Partner of OEM working electro mechanically without any power supply.The recorder shall be of non-resettable type with the electro-mechanical display. No LCD screen is permittted as it may depend upon the battery life to energize the LCD. The lightning stroke recorder shall be duly tested & certified inline with the ESE lightning arrseter in an international labortaory for an impulse current (8/20 micro sec) and should count lightning strokes of 0.4 Ka to 150 Ka. ( Make ABB )

Supply and Laying of Down Conductor G.I.Strip of 40/6 mm ( length - As per Actual), both Verticle and Horizontal, clamping by saddles not exceeding 500 mm apart with 35/8" screw for fixing in wall complete with full threaded bolts with nuts and double washers incl. mending good damages to building work. Finishing the ends of the above Strip by Nut and Bolts, etc.

Hiring charges for Scaffolding arrangement including dismantling at the end of work and carriage, for ESE OPR 30 LA installation.

Supply and Installation by OEM or Authorized channel Partner of OEM of Medium Pipe (10 ft. long, 2" dia G.I.Pipe along with earth rod and Chemical Gel filled with highly conducting metallic compounds with permenant sealings at both ends - ( Make Standard, ISI Brand )for Earthing and for inter connection of Earthing under ground (of 3 meters X 1nos. per pit) with 3 Earth pits of 10 feet deep each.

Supply and Laying of maintenance free earthing terminal which consist of Ground Resistance Improving Furse Cem Conductive Aggregate material, tested as per BS. 1 bag of 25 kg. per Pit, to make it maintenance free and provide low resistance in the earth terminal to be executed by OEM or Authorized channel Partner of OEM only.

R.C.C Civil work for foundation of Lighting arrester mounting must suitable for holding 2000 kg G.I/ M.S structure of 0.5*0.5*1.1 meter along with Nut bolt and base plate.

Lightning arrester mounting structure made with G.I/M.S angle,pipe or strips for holding lighting arrester to 6 meter height to withstand wind power about 120 km/h.

Supply and fixing of 20 W all in one/ Integrated solar street light (Make- Panasonic/Surya/Philips/ as per direction of EIC) along with 6 meter Ms/ G.I pole (Brand approved by EIC) with PIR motion sensor and auto dusk to down incl. suitable concrete foundation as per direction of EIC.

RIK ENTERPRISE (BID ID -6648039)

BABA ELECTRIC (BID ID -6650309)