Loading…
Loading…
| # | Company | Amount | Rank | Status |
|---|---|---|---|---|
| 1 | L1₹48.1 LAccepted-Finance SR NO 281 3 7 ANAND NAGAR NEAR DHANORI JAKAT NAKA LOHEGAON PUNE 411047 | PUNE | PUNE | MAHARASHTRA | 411047 | ₹48.1 L | L1 | Accepted-Finance Being Lowest and reasonable |
| 2 | L2₹49.0 LRejected-Finance 10 AISHWARYA 1ST FLOOR 2ND CROSS ANNAYAPPA GARDEN NEW THIPPASANDRA HAL HAL III STAGE BANGALORE 560075 | BENGALURU URBAN | KARNATAKA | 560075 | ₹49.0 L | L2 | Rejected-Finance Not Being Lowest |
| 3 | L3₹49.2 LRejected-Finance | ₹49.2 L | L3 | Rejected-Finance Not Being Lowest |
| Sl No | Description | Qty | Unit | AishwaryaConstructions L3 | VP DEVELOPERS AND CONTRACTOR L1 | VARALAKSHMI CONSTRUCTIONS L2 |
|---|---|---|---|---|---|---|
| 0.00SCHEDULE OF WORKS | ||||||
| 1.00 | Earth work in surface excavation in all kind of soil not exceeding 30 cm in depth but exceeding 1.5 m in width as well as 10 sqm on plan including getting out and disposal of excavated earth upto 50 metres and lift upto 1.5 metres all as directed by Engineer-in- Charge and as specified and directed. | 463 | SQUARE METRE | 170 ₹78,710 | 200 ₹92,600 | 170 ₹78,710 |
| 2.00 | Earth work in excavation in all kind of soil by mechanical means (Hydraulic excavator) / manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, for all lift, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m, complete all as specified and directed. | 110 | CUBIC METRE | 650 ₹71,500 | 430 ₹47,300 | 600 ₹66,000 |
| 3.00 | Providing and laying in position, cement concrete 1:4:8 (1 cement : 4 manufactured sand derived from Recycled Concrete Aggregate (RCA) : 8 graded stone aggregate 40 mm nominal size Recycled Aggregate (RA) excluding the cost of centering and shuttering - All work up to plinth level, complete all as specified and directed. | 11.6 | CUBIC METRE | 6,000 ₹69,600 | 9,500 ₹1.1 L | 5,900 ₹68,440 |
| 4.00 | Use and waste of formwork to sides of concrete foundations, footings, bases of columns raft and raft beams sides and soffits of foundation and plinth beam and similar work vertical or to batter, complete all as specified and directed. | 7 | SQUARE METRE | 850 ₹5,950 | 650 ₹4,550 | 800 ₹5,600 |
| 5.00 | Use and waste of formwork to sides of pillars, posts, struts, piers, column and stanchions for rough finished surfaces of concrete square, Circular rectangular on plan or polygonal, complete all as specified and directed. | 43 | SQUARE METRE | 850 ₹36,550 | 650 ₹27,950 | 800 ₹34,400 |
| 6.00 | Use and waste of formwork to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including sup- ports, overhangs, etc. also splays between floors and beams, etc. for rough finished surfaces of concrete flat, complete all as specified and directed. | 54 | SQUARE METRE | 850 ₹45,900 | 650 ₹35,100 | 800 ₹43,200 |
| 7.00 | Use and waste of formwork to chajjas, troughs and similar items including edges for rough finished surfaces of concrete flat, complete all as specified and directed. | 3.1 | SQUARE METRE | 1,000 ₹3,100 | 600 ₹1,860 | 1,000 ₹3,100 |
| 8.00 | Use and waste of Formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200mm thick (Horizontal or sloping) for rough finished surfaces of concrete flat, complete all as specified and directed. | 37 | SQUARE METRE | 850 ₹31,450 | 640 ₹23,680 | 850 ₹31,450 |
| 9.00 | M & l for Centering and shuttering including strutting, propping etc. and removal of form work for edges of slab under 20cm wide, complete all as specified and directed. | 34 | RUNNING METRE | 700 ₹23,800 | 230 ₹7,820 | 700 ₹23,800 |
Updated dates
Tender Value
₹49 L
EMD Value
₹97,500
Closing Date
9 Feb 2026, 6:00 pmClosed
GARRISON ENGINEER I Rnd D WEST BANGALORE
GARRISON ENGINEER I RndD WEST BANGALORE DRDO COMPLEX CV RAMAN NAGAR BANGALORE
RECONSTRUCTION OF CHANGING ROOM RENOVATION OF VOLLEY BALL COURT ADDN ALTN TO POST OFFICE BLDG AND TOILET AND PROVN OF WATER COOLERS IN DRDO TOWN SHIP PHASE I CV RAMAN NAGAR BANGALORE
2025_MES_746710_1
GE(I)/R ND D (WEST)/BAN/TOKEN/79 OF 2025-26 8444/E8
Open Tender
Civil Works
270 days
Work
Please refer Tender documents.
9 documents required · 9 mandatory
₹500
GARRISON ENGINEER I RndD WEST BANGALORE
₹97,500
5 Mar 2026
31 Dec 2025
11 Feb 2026
31 Dec 2025
9 Feb 2026
20 Jan 2026
1 Jan 2026 - 7 Jan 2026
Earth work in surface excavation in all kind of soil not exceeding 30 cm in depth but exceeding 1.5 m in width as well as 10 sqm on plan including getting out and disposal of excavated earth upto 50 metres and lift upto 1.5 metres all as directed by Engineer-in- Charge and as specified and directed.
Earth work in excavation in all kind of soil by mechanical means (Hydraulic excavator) / manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, for all lift, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m, complete all as specified and directed.
Providing and laying in position, cement concrete 1:4:8 (1 cement : 4 manufactured sand derived from Recycled Concrete Aggregate (RCA) : 8 graded stone aggregate 40 mm nominal size Recycled Aggregate (RA) excluding the cost of centering and shuttering - All work up to plinth level, complete all as specified and directed.
Use and waste of formwork to sides of concrete foundations, footings, bases of columns raft and raft beams sides and soffits of foundation and plinth beam and similar work vertical or to batter, complete all as specified and directed.
Use and waste of formwork to sides of pillars, posts, struts, piers, column and stanchions for rough finished surfaces of concrete square, Circular rectangular on plan or polygonal, complete all as specified and directed.
Use and waste of formwork to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including sup- ports, overhangs, etc. also splays between floors and beams, etc. for rough finished surfaces of concrete flat, complete all as specified and directed.
Use and waste of formwork to chajjas, troughs and similar items including edges for rough finished surfaces of concrete flat, complete all as specified and directed.
Use and waste of Formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200mm thick (Horizontal or sloping) for rough finished surfaces of concrete flat, complete all as specified and directed.
M & l for Centering and shuttering including strutting, propping etc. and removal of form work for edges of slab under 20cm wide, complete all as specified and directed.
Providing and laying in position ready mixed or site batched design mix Concrete of M25 grade with minimum cement content of 330 kg /cum cement concrete for reinforced cement concrete work; coarse aggregate and fine aggregate derived from natural sources and using recycled concrete aggregate (RCA) as coarse aggregate and fine aggregate within permissible utilization of 20% each, Portland Pozzolana / Ordinary Portland /Portland Slag cement, admixtures in recommended proportions as per IS: 9103 to accelerate / retard setting of concrete, to improve durability and workability without impairing strength; including pumping of concrete to site of laying, curing, carriage for all leads; but excluding the cost of centering, shuttering, finishing and reinforcement as per direction of the engineer-in-charge; for the following grades of concrete. All works upto plinth level, complete all as specified and directed. Note: In case the cement content in design mix is more than the specified minimum cement content, the contractor is liable to bear the cost of extra cement.
Same as above but All RCC works above plinth level incl beams, slab, Chajja and facia etc, complete all as specified and directed.
M&L for Thermo-Mechanically Treated bars of grade Fe-500D or more, 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips, complete all as specified and directed.
All as per item No.12 but 5mm dia and over upto and including 10mm dia in stirrups, spacers and binders, complete all as specified and directed.
M & L for Anti-Termite treatment by treating the backfill in contact with foundation at the rate of 7.5 litres of emulsion per square metre of vertical surface (Area of the sub structure in contact with backfill to be measured) complete all as specified and directed.
M & L for Anti-Termite treatment by treating the top surface of filled earth at the rate of 5 litres of emulsion per square metre of surface, complete all as specified and directed.
M & L for Anti-Termite treatment by treating the soil under plinth protection at the rate of 5 litres of emulsion per square metre of surface area, complete all as specified and directed.
M & L for Anti-Termite treatment by treating the soil along with external perimeter of building at the rate of 2.25 litre of emulsion per metre of the perimeter wall, complete all as specified and directed.
M&L for Pre-cast cement concrete block masonry with solid blocks in cement concrete 1:3:6 mix, type C1(using 20mm graded stone aggregat) exc. 10 cm in width and setting in cement mortar (1: 4) complete all as specified and directed.
Providing and laying half block masonry with factory made Precast concrete solid blocks of 100 mm thickness of grade M10 made of C&D waste from approved manufacturer in superstructure above plinth level up to floor V level and setting in cement mortar (1: 4) complete all as specified and directed.
Providing and laying damp-proof course 40mm thick with cement concrete 1:2:4 (1 cement : 2 coarse sand (zone-III) including manufactured sand derived from Recycled Concrete Aggregate (RCA) upto 25% : 4 graded stone aggregate 12.5mm nominal size including (Recycled Concrete Aggregate (RCA) upto 25%)) Note :- Water proofing compound will be measured and paid separately under relevant of this BOQ, complete all as specified and directed.
Providing & applying a coat of residual petroleum bitumen of grade of VG-10 of approved quality using 1.7kg per square metre on damp proof course after cleaning the surface with brushes and finally with apiece of cloth lightly soaked in kerosene oil, complete all as specified and directed.
Providing plain cement concrete in 1:2:4 mix, type B0, (using 12.5mm graded stone aggregate) as in coving concrete in chajjas, in roof kerbs or mud stops, rounded or chamfered on edges, complete all as specified and directed.
Material and labour for 10mm thick rendering in cement mortar 1:6 to be finished even and smooth (without using extra cement) , on fair faces of brick work or concrete surfaces complete all as specified and as directed.
Material and labour for 5mm thick cement plaster of mix 1:3 (1 cement : 3 fine sand) on ceiling surfaces/RCC members complete all as specified and as directed.
Material and labour for 15 mm thick cement plaster in CM 1:4 on rough side of brick wall finished with a floating coat of neat cement of mix mixed with WPC finished rough with sponge, complete all as specified and directed. Note :- Water proofing compound will be measured and paid separately under relevant of this BOQ.
Supply only liquid water proofing compound
Add for plaster drip course/ groove in plastered surface or moulding to R.C.C. projections, complete all as specified and directed.
M & L for wire netting of galvanised steel wire 1.40mm dia and size of mesh 20 mm fixed in walls before plastering on junction of wall/RCC junction all as specified and as directed
Providing and laying in position cement concrete as in sub base of grade 1:4:8 (1 cement : 4 manufactured sand derived from Recycled Concrete Aggregate (RCA) : 8 graded stone aggregate 40 mm nominal size Recycled Aggregate (RA), complete all as specified and directed.
Providing and laying in position cement concrete as in base of grade 1:2:4 (1 cement : 2 coarse sand (zone-III) including manufactured sand derived from Recycled Concrete Aggregate (RCA) upto 25% : 4 graded stone aggregate 20 mm nominal size including Recycled Concrete Aggregate (RCA) upto 25%), complete all as specified and directed.
Providing and laying Glazed Vitrified tiles Matt/Antiskid finish of Size of Tile 600 x 600 mm (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS:15622, of approved brand & manufacturer, in all colours and shade, laid on 20 mm thick cement mortar screed in CM1:4 (1 cement: 4 coarse sand) jointing with grey cement slurry @3.3 kg/sqm including grouting the joints with white cement and matching pigments etc. The tiles must be cut with the zero chipping diamond cutter only . Laying of tiles will be done with the notch trowel, plier, wedge, clips of required thickness, leveling system and rubber mallet for placing the tiles gently and easily, complete all as specified and directed.
Providing and laying Vitrified tiles Size of Tile 600x600 mm (thickness to be specified by manufacturer), with water absorption less than 0.08 % and conforming to I.S. 15622, of approved make, in all colours & shade, in skirting, riser of steps, over 12 mm thick bed of cement mortar in CM 1:3 (1 cement: 3 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joint with white cement & matching pigments etc, complete all as specified and directed.
Providing and laying Non skid Ceramic floor tiles of size 300x300 mm (thickness to be specified by the manufacturer) of 1st quality conforming to IS : 15622 of approved make in colours such as White, Ivory, Grey, Fume Red Brown, laid on 20 mm thick cement mortar screed in CM 1:4 (1 Cement : 4 Coarse sand), Jointing with grey cement slurry @ 3.3 kg/sqm including pointing the joints with white cement and matching pigment etc, complete all as specified and directed.
Providing and fixing 1st quality ceramic glazed wall tiles conforming to IS : 15622 (thickness to be specified by the manufacturer ) of approved make in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge in skirting, risers of steps and dados over 12 mm thick bed of cement Mortar 1:3 (1 cement: 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm including pointing in white cement mixed with pigment of matching shade, complete all as specified and directed.
Providing and fixing 18 mm thick gang saw cut, mirror polished Granite stone slab of colour black area of slab over 0.50 sqm, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing of edges to give high gloss finish etc. complete at all levels, complete all as specified and directed.
Providing edge moulding to 18 mm thick Granite counters, Vanities etc., including machine polishing to edge to give high gloss finish, grooving etc. complete all as specified and directed.
Supply and fixing white vitreous china pedestal type water closet (European type) with W.C. pan with ISI marked white solid plastic seat and lid, 10 litre low level white vitreous china flushing cistern & C.P. flush bend with fittings & C.I. brackets, 40 mm flush bend, overflow arrangement with specials of standard make and mosquito proof coupling of approved municipal design complete, including painting of fittings and brackets, cutting and making good the walls and floors wherever required and including dismantling of old WC seat and "S" or "P" trap at site complete with all operations including all necessary materials, labour and disposal of dismantled material i/c malba, all complete as per the direction of Engineer-in charge. :
Providing and fixing counter sunk wash basin size 550x400 mm with a pair of 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require: all complete as per the direction of Engineer-in charge, complete all as specified and directed.
Providing and fixing white vitreous china flat back or wall corner type lipped front urinal basin of 430x260x350 mm or 340x410x265 mm sizes respectively including providing and fixing PTMT 15 mm Urinal spreader size 95x69x100 mm with 1/2" BSP thread and shapes, weighing not less than 60 gms, complete all as specified and directed.
Providing and fixing Granite Stone of approved shade with table rubbed, edges rounded and polished, of size 75x50 cm deep and 1.8 cm thick, fixed in urinal partitions by cutting a chase of appropriate width with chase cutter and embedding the stone in the chase with epoxy grout or with cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 6 mm nominal size) as per direction of Engineer-in-charge and finished smooth, complete all as specified and directed.
S&F CP brass Tubular towel rail, 20mm dia, D type, 60cm long between flanges, complete all as specified and directed.
S&F Towel Ring of C.P. brass fixed with and including Chromium plated brass screws and wooden/plastic cleats (Minimum weight 90gms), complete all as specified and directed.
Providing and fixing in repair 600x450 mm beveled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers, complete all as specified and directed.
S&F facny type Health faucet (ABS Body) mild steel chromium plated suitable for 15 mm dia pipe with 1.25 metre long flexible tube and ABS wall hook including fixed in position complete in all respects, complete all as specified and directed.
S&F fancy type chromium plated 2 way bib tab 15mm dia with CP flange as fixed in repair, complete all as specified and directed.
Providing and fixing C.P. brass stop cock (concealed) of standard design and of approved make conforming to IS:8931. of 15 mm nominal bore, complete all as specified and directed.
Providing and fixing C.P. brass angle valve 15 mm nominal bore for basin mixer and geyser points of approved quality conforming to IS:8931, complete all as specified and directed.
Providing and fixing CP Brass 32mm size Bottle Trap of approved quality & make and as per the direction of Engineer-in-charge, complete all as specified and directed.
Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes of 15 mm internal dia Pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge. Note: The rates includes for pipes including short lengths, with all pipe fittings such as ends, elbows, unions, tees, reducing tees, adoptors, sockets, plugs, hose clips etc. and fixing to walls etc, complete with saddles (snap clips), wall clips, hooks, protective tube sleeves and cutting through walls, etc
All as per Sl.No. 49 here-in-above but 20 mm internal dia Pipes
Providing and fixing Fiber Glass Reinforced plastic (FRP) Door Frames of cross-section 90 mm x 45 mm having single rebate of 32 mm x 15 mm to receive shutter of 30 mm thickness. The laminate shall be moulded with fire resistant grade unsaturated polyester resin and chopped mat. Door frame laminate shall be 2mm thick and shall be filled with suitable wooden block in all the three legs. The frame shall be covered with fiber glass from all sides. M.S. stay shall be provided at the bottom to steady the frame, complete all as specified and directed.
Providing and fixing 30 mm thick Glass Fibre Reinforced Plastic (FRP) panelled door shutter of required colour and approved brand and manufacture, made with fire - retardant grade unsaturated polyester resin, moulded to 3 mm thick FRP laminate for forming hollow rails and styles, with wooden frame and suitable blocks of seasoned wood inside at required places for fixing of fittings, cast monolithically with 5 mm thick FRP laminate for panels conforming to IS: 14856, including fixing to frames, complete all as specified and directed.
Providing and fixing factory made single extruded WPC (Wood Polymer Composite) solid door/window/Clerestory windows & other Frames/Chowkhat Frame size 65 x 100 mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2, modulus of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixed in position with M.S hold fast/lugs/SS dash fasteners of required dia and length complete as per direction of Engineer-In- Charge. (M.S hold fast/lugs or SS dash fasteners shall be paid for separately).
Supply and fix 30 mm thick factory made single extruded WPC (Wood Polymer Composite) solid plain flush door shutter of required size comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, all as per direction of Engineer-In- Charge. (Note: stainless steel butt hinges and necessary S.S screws shall be paid separately)
Providing and fixing factory made single extruded WPC (Wood Polymer Composite) solid board of 18mm thick one side white color and other side of board laminted with PVC foil of minimum 14 micron thickness of approved design pasted with hot melt adhesive for cup boards, work stations and bathroom/kitchen cabinet etc. of required sizes comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixing with stainless steel piano hinges/soft close clip on concealed hinges of required size with necessary full body threaded star headed counter sunk S.S screws, all as per direction of Engineer-In- Charge. (Note: stainless steel piano hinges/soft close clip on concealed hinges and necessary S.S screws shall be paid separately)
Providing and fixing Powder coated aluminium sections (minimum thickness of powder coating 50 micron) for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ 3 Track sliding window / appropriate Z sections and other sections of approved make conforming to IS: 733 nd IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections hall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / paneling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing, paneling and dash fasteners to be paid for separately)
Providing and fixing Powder coated aluminium sections (minimum thickness of powder coating 50 micron) for shutters of doors, windows & ventilators/Grill including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber / neoprene gasket required, complete all as specified and directed.
S&F 4mm thick sheet glass ordinary quality and glazing with oil putty in square n exc 0.5 sq. m in each pane in aluminium window shutter, complete all as specified and directed.
S&F 4mm thick Figured glass, pin head type and glazing with oil putty in squares n exc 0.5 sq. m in each pane in aluminium window shutter, complete all as specified and directed.
Providing and fixing fly proof stainless steel grade 304 wire gauge, to windows and clerestory windows using wire gauge with average width of aperture 1.4 mm in both directions with wire of dia. 0.50 mm all complete with 12 mm mild steel U beading, complete all as specified and directed.
Providing M.S. Piano hinges over all width 50mm ISI marked IS : 3818 finished with nickel chromium plating grade 1 as per IS: 1068 and fixing with necessary screws etc., complete all as specified and directed.
Providing and fixing magnetic Double strip (horizontal type) catcher of approved quality in cupboard / ward robe shutters, including fixing with necessary screws etc, complete all as specified and directed.
Providing and fixing bright finished 100 mm brass handles with screws etc, complete all as specified and directed.
Providing and fixing 20mm dia brass curtain rods of wall thickness 1.25 mm with two brass brackets fixed with brass screws and wooden plugs etc. wherever necessary, complete all as specified and directed.
Providing and fixing square-mouth S.W. gully trap 100x100 mm size P type class SP-1 complete with C.I. grating brick masonry chamber with water tight C.I. cover with frame of 300 x300 mm size (inside) the weight of cover to be not less than 4.50 kg and frame to be not less than 2.70 kg as per standard design incl demolition of exising gully trap, complete all as specified and directed.
Providing and fixing on wall face/under floor unplasticised Rigid PVC pipes 110 mm dia conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion, (i) Single socketed pipes, complete all as specified and directed.
Providing and fixing on wall face/under floor unplasticised Rigid PVC pipes 75 mm dia conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion, (i) Single socketed pipes, complete all as specified and directed.
Providing and fixing on wall face/under floor 75 mm bend unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion, complete all as specified and directed.
Providing and fixing on wall face/under floor 110 mm bend unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion, complete all as specified and directed.
Providing and fixing on wall face/under floor 75x75x75 mm Single tee with door unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVCpipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion, complete all as specified and directed.
Providing and fixing on wall face/under floor 110x110x110 mm Single tee with door unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVCpipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion, complete all as specified and directed.
S&F PVC (SWR) floor trap with and including, plain / single hole chromium plated grating including jointing to waste pipe with solvent cement, 75mm dia, complete all as specified and directed.
Supply and fix for PVC (SWR) pipe 40 mm dia conforming to IS:4985-2000 with solvent cement joints laid on floor or on walls fixed as drain pipe in wash hand basins, spout pipes in balconies etc. including taking up or down existing PVC pipes and connections complete all as specified and as directed.
S&F PVC (SWR) vent cowl of 110mm dia
Providing and applying 1mm thick wall care putty on wall over plastered surface to prepare the surface even and smooth, complete all as specified and directed.
M&L for preparation of newly plastered or unplastered surfaces of walls and applying two coat of distemper oil emulsion white tinted over a coat of alkali resistant primer complete all as specified and directed.
M&L for preparation of newly plastered or unplastered surfaces of ceiling and applying two coat of distemper oil emulsion white tinted over a coat of alkali resistant primer complete all as specified and directed.
Material & Labour for applying two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over new surfaces, complete all as specified and directed.
M & L for Painting with synthetic enamel paint Two or more coats on new work over an under coat of suitable shade with ordinary paint of approved brand and manufacture, complete all as specified and directed.
Providing and fixing 20mm nominal bore gun metal gate valve with C.I. wheel of approved quality (screwed end), complete all as specified and directed.
Providing and fixing aluminium tower bolts 150x10 mm ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868 ) transparent or dyed to required colour or shade with necessary screws etc, complete all as specified and directed.
Providing and fixing aluminium tower bolts 100x10 mm ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868 ) transparent or dyed to required colour or shade with necessary screws etc, complete all as specified and directed.
Providing and fixing aluminium handles 125 mm ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade with necessary screws etc, complete all as specified and directed.
Providing and fixing aluminium sliding door bolts, ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868), transparent or dyed to required colour or shade, with nuts and screws etc., 300x16 mm, complete all as specified and directed.
Providing and fixing IS : 12817 marked stainless steel butt hinges with stainless steel screws etc. complete : 75x47x1.80 mm, complete all as specified and directed.
Material and labour for roof treatment as follows:- Providing and applying fibre reinforced elastomeric liquid water proofing membrane with resilient acrylic polymers having Sun Reflectivity Index (SRI) of 105 on top of concrete roof in three coats @10.76 litre/ 10 sqm. One coat of self-priming of elastomeric waterproofing liquid (dilution with water in the ratio of 3:1) and two coats of undiluted elastomeric waterproofing liquid (dry film thickness of complete application/system not less than 500 microns). The operation shall be carried out after scrapping and properly cleaning the surface to remove loose particles with wire brushes, complete in all respect as per the direction of Engineer-in-Charge.
Providing and placing on terrace (at all floor levels) Rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top) , three layered conforming to IS : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank, complete all as specified and directed.
Providing and fixing ball valve (brass) 20 mm nominal bore of approved quality, High or low pressure, with plastic floats, complete all as specified and directed.
Providing plinth protection 50mm thick in plain cement concrete of 1:3:6 mix (1 cement : 3 manufactured sand derived from Recycled Concrete Aggregate (RCA) : 6 graded stone aggregate 20 mm nominal size Recycled Concrete Aggregate (RCA) over 75mm thick bed of dry brick ballast 40 mm nominal size, well rammed and consolidated and grouted with fine sand, including necessary excavation, levelling & dressing & finishing the top smooth, complete all as specified and directed.
Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 and for all lift, complete all as specified and directed.
Disposal of moorum/building rubbish/ malba/ similar unserviceable, dismantled or waste material by mechanical transport including loading, transporting, unloading to approved municipal dumping ground for lead upto 10 km for all lifts, complete as per directions of Engineer-in-charge, complete all as specified and directed.
Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level 1:2:4 (1 cement : 2 coarse sand (zone-III) including manufactured sand derived from Recycled Concrete Aggregate (RCA) upto 25% : 4 graded stone aggregate 20 mm nominal size including Recycled Concrete Aggregate (RCA) upto 25%), complete all as specified and directed.
Providing and laying factory made Precast concrete solid blocks of 200 mm thickness of grade M10 made of C&D waste from approvedmanufacturer in foundation and plinth in Cement mortar 1:6 (1 cement : 6 coarse sand), complete all as specified and directed.
Steel work welded in built up sections/ framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required in gratings, frames, guard bar, ladder, railings, brackets, gates and similar works using steel sections of Fe-290 (Gde E-165) complete all as specified and directed.
Supplying and Laying 150mm compacted thick (in two layers of 75mm thick each), spreading and compacting using stone aggregate of 63 mm to 45 mm size, hand picking, rolling with 3 wheeled road/vibratory roller 8-10 tonne capacity in stages to proper grade and camber, applying and brooming requisite type of screening / binding material to fill up interstices of coarse aggregate, watering and compacting to the required density, complete all as specified and directed.
Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level 1:3:6 (1 Cement : 3 manufactured sand derived from Recycled Concrete Aggregate (RCA) : 6 graded stone aggregate 20 mm nominal size ecycled Concrete Aggregate (RCA), complete all as specified and directed.
Providing and laying design mix cement concrete of M-25 grade Cement co prepared with batch mixing machine, in roads/ taxi tracks/ runways, using cement content as per design mix, using coarse sand and graded stone aggregate of 20 mm nominal size in appropriate proportions as per approved & specified design criteria, providing dowel bars with sleeve/ tie bars wherever required, laying at site, spreading and compacting mechanically by using needle and surface vibrators, levelling to required slope/ camber, Vaccum Dewatering process finishing with required texture, including steel form work with sturdy M.S. channel sections, curing, making provision for contraction/ expansion, construction & longitudinal joints (10 mm wide x 50 mm deep) by groove cutting machine, providing and filling joints with approved joint filler and sealants, complete all as per direction of Engineer-in-charge (Item of joint fillers, sealants, dowel bars with sleeve/ tie bars to be paid separately).
Supply and laying of ITF classified 8 layer all weather Synthetic cushion surface System complete all as specified and directed.
Providing and filling in position rubberized bitumen hot sealing compound for sealing of expansion/contraction/dummy joints in roads / pavements all complete as per direction of the Engineer-in-Charge.
Providing and fixing G.I. Pipes 15 mm dia nominal bore with G.I. fittings and clamps, including painting with anti corrosive bitumastic paint, cutting chases for concealed piping and making good the wall, complete all as specified and directed. .
Providing and laying 60mm thick factory made cement concrete interlocking paver block of M -30 grade made by block making machine with strong vibratory compaction, of approved size, design & shape, laid in required colour and pattern over and including 50mm thick compacted bed of coarse sand, filling the joints with line sand etc. all complete as per the direction of Engineer-in-charge.
M & L for Chequerred precast cement concrete tiles 22 mm thick in footpath & courtyard, jointed with neat cement slurry mixed with pigment to match the shade of tiles, including rubbing and cleaning etc. complete, on 20 mm thick bed of cement mortar 1:4 (1 cement: 4 coarse sand) finished with Dark shade pigment using ordinary cement, complete all as specified and directed.
Demolishing R.C.C. work manually/ by mechanical means including stacking of steel bars and disposal of unserviceable material removing debris outside MD land lead as per direction of Engineer - in- charge, complete all as specified and directed.
Demolishing cement concrete of any description, manually/ by mechanical means including disposal of material within 50 metres lead as per direction of Engineer - in - charge, complete all as specified and directed.
Demolishing brickwork in cement mortar, manually/ by mechanical means including stacking of serviceable material and disposal of unserviceable material removing debris outside MD land as per direction of Engineer-in-charge.
Dismantling doors, windows and clerestory windows (steel or wood) shutter including chowkhats, architrave, holdfasts etc. complete and stacking within 50 metres lead, of area 3 sq. metres and below all as specified and as directed.
Dismantling 15 to 40 mm dia G.I. pipe including stacking of dismantled pipes (within 50 Metres lead) as per direction of Engineerin-Charge
Disconnecting damaged overhead/terrace PVC water storage tank of any size from water supply line and removing from the terrace including shifting at ground level as per direction of Engineer-in-charge.
Cutting holes into or through brick walls built in cement mortar, superficial area not exceeding 150sq.cm, and making good in cement mortar 1:3 or cement concrete 1:2:4 type B1 (20mm graded stone aggregate) as required, complete all as specified and directed.
Providing and fixing 15 mm nominal dia Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge
Taking down eaves gutters and rainwater pipes (any size or pattern) including all fittings, heads, shoes, bends, swan-necks, etc., including cleaning or refixing or removal to Store (measured overall as fixed along the centre line over fittings and accessories)
Providing and fixing on wall face/floor 75mm dia unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including clamping,jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion, (i) Single socketed pipes, complete all as specified and directed.
S&F PVC (SWR) bends any radius, 75mm bore, complete all as specified and directed.
S&F PVC (SWR) junction single 'T' equal or unequal 75 mm bore complete all as specified and directed.
Providing and fixing on wall face 110mm dia unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including clamping,jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion, (i) Single socketed pipes, complete all as specified and directed.
S&F PVC (SWR) bends any radius, 110mm bore , complete all as specified and directed.
S&F PVC (SWR) bends any radius, 110mm bore with access door, complete all as specified and directed.
Providing and fixing in repair C.P. brass stop cock (concealed) of standard design and of approved make conforming to IS:8931. of 15 mm nominal bore, complete all as specified and directed.
Providing and fixing uplasticised PVC connection pipe with brass unions 60 cm length and 15 mm nominal bore, complete all as specified and directed.
Dismantling tile work in floors and walls laid in cement mortar , for thickness of tiles 8 mm to 25 mm including stacking material removing debris outside MD land, complete all as specified and directed.
M&L non skid ceramic coloured tiles 7 to 8mm thick (square /rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match the colour of tiles including Screed bed or bedding layer of mortar 15 mm thick for laying floor finishes in cement mortar 1:6, complete all as specified and directed.
Providing and fixing Ist quality ceramic glazed wall tiles of size 300x450 mmconforming to IS: 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade complete.
Distempering with 1st quality acrylic distemper (ready mixed) having VOC content less than 50 gram/litre, of approved manufacturer and of required shade and colour all complete to achieve even shade and colour New work (two or more coats) over and including water thinnable priming coat with cement primer having VOC content less than 50 gram/litre (wall/ceiling), complete all as specified and directed.
Supply and fixed in repair Single towel rail brass chromium plated 600mm long fixed with chromium plated screw and PVC cleat etc complete all as specified and directed.
Providing 1:2:4 (1 cement : 2 coarse sand (zone-III) derived from natural sources : 4 graded stone aggregate 20 mm nominal size derived from natural sources) and laying in position cement concrete of specified grade excluding the cost of centering and shuttering, complete all as specified and directed.
Providing and fixing 15mm C.P. brass long body bib cock of approved quality conforming to IS standards and weighing not less than 690 gms, complete all as specified and directed.
S&F in repairs Providing and fixing C.P. brass shower rose 150 mm diameter with 15 or 20 mm inlet incl shower arm quality & make as approved by Engineer in charge.
S&F in repair Providing and fixing floor mounted, white vitreous china single piece,double traps syphonic water closet of approved brand/make, shape, size and pattern including integrated white vitreous china cistern of capacity 10 litre with dual flushing system, including all fittings and fixtures with seat cover, cistern fittings, nuts, bolts and gasket etc including making connection with the existing P/S trap, complete in all respect as per directions of Engineer-in-Charge
S&F in repair centre hole wash basin mixture valve, cast copper alloy fancy type (swan neck) 15mm brass chromium plated mixer (central hole basin mixer w/o pop up waste system) for mixing hot & cold water screwed down for iron pipe , complete all as specified.
Sheet glass shelf assembly consisting of 5mm thick sheet glass shelf 12cm wide with chromium plated bracket guard and railing 60cm long, complete all as specified and directed.
Providing and fixing P.V.C. Flexible waste pipe for sink or wash basin including P.V.C. waste fittings complete ,40 mm dia., complete all as specified and directed.
Providing and fixing CP Waste Coupling for wash basin and sink, of approved quality Waste coupling 38 mm dia of 83 mm length and 77mm breadth, weighing not less than 60 gms, complete all as specified and directed.
Providing and fixing factory made P.V.C. door frame of size 50x47 mm with awall thickness of 5 mm, made out of extruded 5mm rigid PVC foam sheet, mitred at corners and joined with 2 Nos of 150 mm long brackets of 15x15 mm M.S. square tube, the vertical door frame profiles to be reinforced with 19x19 mm M.S. square tube of 19 gauge, EPDM rubber gasket weather seal to be provided through out the frame. he door frame to be fixed to the wall using M.S. screws of 65/100 mm size, complete as per manufacturer’s specification and direction of Engineerin- Charge.
Providing and fixing factory made panel 30mm PVC door shutter consisting of frame made out of M.S. tubes of 19 gauge thickness and size of 19 mm x 19 mm for styles and 15x15 mm for top & bottom rails. M.S. rame shall have a coat of steel primers of approved make and manufacture.M.S. frame covered with 5 mm thick heat moulded PVC 'C' channel of size 30 mm thickness, 70 mm width out of which 50 mm shall be flat and 20 mm shall be tapered in 45 degree angle on both side forming styles and 5 mm thick, 95 mm wide PVC sheet out of which 75mm shall be flat and 20 mm shall be tapered in 45 degree on the inner side to form op and bottom rail and 115 mm wide PVC sheet out of which 75 mm shall be flat and 20 mm shall be tapered on both sides to form lock rail. Top, bottom and lock rails shall be provided both side of the panel 10 mm 5 mm x 2 ) thick, 20 mm wide cross PVC sheet be provided as gap insert for top rail & bottom rail, paneling of 5 mm thick both side PVC sheet to be fitted in the M.S. frame welded/ sealed to the styles & rails with 7 m (5 mm+2 mm) thick x 15 mm wide PVC sheet beading, on inner side, and joined together with solvent cement adhesive. An additional 5 mm thick PVC strip of 20 mm width is to be stuck on the interior side of the 'C' hannel using PVC solvent adhesive etc. complete as per direction of Engineer-in-charge, manufacturer's specification & drawing. complete all as specified and as directed.
Supply and fix galvanised wire mesh of average width of aperture 1.4 mm and nominal dia of wire 0.63 mm, complete all as specified and directed.
Providing and fixing Two and half track three panels sliding window with two glazed & one wire mesh panels with Aluminium channel for roller track, wool pile, nylon rollers with SS 304 body.Using R2 series with frame (65mm & above) x (40mm & above) & glazed sash (25mm & above) x (50mm & above) & fly screen sash (18mm & above) x (40mm & above) with zinc alloy (zamak) powder coated touch locks with hook (Height upto 1.2 metre). factory made uPVC glazed/wire mesh windows/doors comprising of lead free uPVC multi-chambered frame, sash and mullion/coupler (where ever required) extruded profiles having minimum wall thickness of 1.70 mm for Series R1 and R2 profiles and 2.10 mm for Series R3 and R4 profiles conforming to EN: 12608 in any shape, colour and design duly reinforced with galvanized mild steel section made of required shape & size as per CPWD Specification, uPVC extruded glazing beads, interlocks and Inline sash adaptor (where ever required) of appropriate dimension, EPDM gasket, hardware, SS 304 grade fasteners of minimum 8 mm dia with countersunk head, comprising of matching polyamide PA6 grade sleeve for fixing frame to finished wall as per IS 1367 : Part 1 to 14, plastic packers, plastic caps and necessary stainless steel screws etc. Profile of frame, sash & mullion (if required) shall be mitred cut and fusion welded/mechanically jointed duly sealed at all corners, including drilling of holes for fixing hardware and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealant over backer rod of approved size and quality, all complete as per approved drawing conforming to CPWD specification & direction of Engineer-in-Charge. Section of steel reinforcement and cross sections of uPVC profiles to be as per design approved by Engineer-in-Charge. Note:- Structural design proof checked from a Government Engineering Institute, to be provided by the manufacturer for : (i) Sites with basic wind speed > 45 m/sec as per IS 875 – Part 3 (ii) Sites with structure height more than 20m for all wind speeds
Supply and fix Float glass panes of nominal thickness 4 mm (weight not less than 10 kg/sqm), complete all as specified and directed.
Providing and fixing 115mm oxidised M.S. hasp and staple (safety type) conforming to IS : 363 with necessary screws etc. complete : (copper oxidized as per IS: 1378),complete all as directed.
S&F, Auto closing hinges 35mm of 0 crank (KH-001) or B crank (KH-002) openable at 110 degree for kitchen cabinet shutters fixed in repair complete all as specified and directed.
S&F Fancy type stainless steel handle of size 100 mm long complete all as specified and directed approved by GE, complete all as specified and directed.
Dismantling of composite steel windows/ventilators shutters only n.exc 0.60 Sqm single leaf double shutter with fixed portion including glass panes mosquito proof mesh, etc .(ONLY SHUTTER DISMANTLING), complete all as specified and directed.
Dismantling of composite steel windows/ventilators shutters exc 0.60 Sqm but not exc 1.80Sqm double leaf double shutter with fixed portion including glass panes mosquito proof mesh, guard bars etc.( ONLY SHUTTER DISMANTLING), complete all as specified and directed.
Providing and fixing G.I. pipes 20 mm dia nominal bore complete with G.I. fittings and clamps, i/c cutting and making good the walls etc all as specified and directed
S & F PVC (SWR) multi-floor trap, plain with chromium plated grating including jointing with solvent cement, 75mm dia, complete all as specified and directed.
S&F in repair vitreous china wash hand basin white colour ,ceramic over counter ,oval shape size 45x45x20 cm complete including CP brass coupling all as specified and directed.
Providing and fixing 600x450 mm beveled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete.
S&F in repair PVC cabinet mirror of size 300x450mm fixed with screw and PVC gutty on wall complete all as specified and directed
Dismantling old plaster or skirting raking out joints and cleaning the surface for plaster including disposal of rubbish to the dumping ground outside of the MD land.
Material and labour,12 mm cement plaster finished with a floating coat of neat cement of mix in Cement mortar 1:6, on brick work/concrete surfaces complete all as specified and as directed
Dismantling stone slab flooring laid in cement mortar including stacking of serviceable material and disposal of unserviceable material within 50 Metres lead.
Providing and laying flamed finish Granite stone Jet Black, Cherry Red, Elite Brown, Cat Eye or equivalent. Slabs flooring in required design and patterns, in linear as well as curvilinear portions of the building all complete as per the architectural drawings with 18 mm thick stone slab over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with cement slurry and pointing with white cement slurry admixed with pigment of matching shade including rubbing, curing and polishing etc. all complete as specified and as directed by the Engineer-in-Charge :
Providing edge moulding to 18 mm thick Granite marble stone counters, Vanities etc., including machine polishing to edge to give high gloss finish etc. complete as per design approved by Engineer-in-Charge.
Providing and fixing Stainless Steel A ISI 304 (18/8) Kitchen sink with drain board of size 510x1040 mm bowl depth 250 mm as per IS:13983 with C.I. brackets and stainless steel plug 40 mm, including painting of fittings and brackets, cutting and making good the walls wherever required
Providing and fixing P.V.C. Flexible waste pipe for sink or wash basin including P.V.C. waste fittings complete ,40 mm dia.
Providing and fixing C.P. brass swan neck pillar tap for 15 mm nominal bore of approved quality conforming to IS standards and weighing
Providing and fixing P.V.C. low level flushing cistern 10 litre capacity - White with manually controlled device (handle lever) conforming to IS : 7231, with all fittings and fixtures complete.
Providing and fixing unplasticised P.V.C. connection pipe 15 mm nominal bore with 45 cm length PTMT Nuts, collar and bush of approved quality and colour.
Providing and fixing PTMT towel rail 600 mm long towel rail with total length of 645 mm, width 78 mm and effective height of 88 mm, weighing not less than 190 gms.complete with brackets fixed to wooden cleats with CP brass screws with concealed fittings arrangement of approved quality and colour.
M & L for Towel Ring of PTMT fixed with and including Chromium plated brass screws and wooden/plastic cleats (Minimum weight 90gms)
S&F in repair SS chromium plated, peg set of four/five fixed with screw complete all as specified and directed.
S&F for Corner glass shelf assembly consisting of 5mm thick sheet glass shelf 30cm wide with chromium plated bracket guard and railing. complete all as specified and directed.
Centering and shuttering including strutting, propping etc. and removal of form for Shelves (Cast in situ)
Brass chromium plated, fancy type, soap dish, as per Cat Part No. F450022 of Hindware or equivalent in other makes, and fixing with brass screws, complete all as specified and directed.
S&F, Stainless steel Plate rack 775X750X 0.6mm thick, complete all as specified and directed.
S&F in repair Vitreous china Urinal, Half stall type, white (excluding flushing cistern, flush pipe and waste pipe) complete incl providing and fixing plugs, beddding urinal against wall in cement mortar 1:2, securing urinal to plug with and including 60mm long brass screw, pointing around urinal back in cement; including waste pipe.
M&L for water spreader for urinals chromium plated fixed with screws and wooden/PVC gutty complete all as specifed & directed.
Supply,installation,commissioning of Water Cooler of capacity 40/80 Litres stainless steel ,electric driven single phase having approximate storage and nominal capacity including all required accessories and connections etc complete all as specified and directed by Engineer-in-charge.
S& F suitable size GI/ PVC box with modular plate and cover in front of surface including providing and fixing 3pin 5/6A modular socket outlet and 5/6A modular switch connections etc completed all as specified and directed by Engineer-in-charge
Material and labour for circuit/submain wiring with 2 runs of 1.5 sqmm single core, PVC insulated, unsheathed, multistranded copper conductor cable, FRLS type, 1100 volts grade conforming to IS-694 drawn through in and including non-metallic rigid PVC conduit 25mm dia medium grade and conduit accessories concealed in walls floors except in roofs duty chases cutting groove by chisselling or mechanically as required and making good the disturbed surfaces to match with existing surface including 1.5 sqmm PVC insulated, single core, unsheathed, multistranded copped conductor cable, FRLS type, 1100 votls grade conforming to IS-694as earth contuinity conductor and connecting to common earth dolly complete all as specified and directed by Engr-in-charge .NOTE:-2 runs of 1.5sqmm copper conductor and 1 run of 1.5sqmm copper conductor earth wire and 1 run of PVC conduit shall be measured as on unit
M & L for cutting the existing steel tubing for making water tap connections at pipe of 25/20mm dia,including threading and fixing with Tee ,nipple etc all as specified and as directed.
S & F of Stop valves, of 15mm dia cast copper alloy,screwed down,high pressure,with crutch or butterfly handle,screwed both ends for iron pipe or for unions and fixede and connecting complete all as specified & as directed.
S & F GI pipe medium grade 15mm dia including necessory connection to existing supply line and clamping to walls etc complete including fittings all as directed.
M & L for construction of platform of size 75x75x30 cm for water cooler of 40/80 Ltr in 1;3;6 ( using 40mm graded stone aggregate) in cement concrete including foundation,filling and mass concrete ,necessay drain pipes etc complete etc complete all as specified and directed by Engr-in-charge
Taking down copper/aluminium point wiring (light, fan, socket or power) complete, including fixture and fittings such as switches, ceiling roses, pendants, regulators, sockets, light fitting etc. removing materials to store for keeping in safe custody or for taking credit (credit for above items should be made as per conditions separately) and making good disturbed surfaces of walls, floors, etc. complete all as specified and directed.
Material and Labour for Wiring for One 5 Amps socket point on the independent board with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface medium class PVC casing/capping or conduit, with modular switch, modular plate, suitable GI / PVC box and earthing the point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable etc.
Material and labour for point wiring for light point/fan point/exhaust fan point/call bell point with 1.5 Sqmm (nominal area) FRLS PVC insulated unsheathed multi stranded copper conductor of size 1.5 Sqmm cable drawn in and including concealed rigid PVC conduit medium grade not less than 20mm dia with accessories like with modular switch, modular plate, suitable GI box and earthing the point including cutting chases for laying of conduit /fixing of boxes in walls/floor etc including making good to disturbed surfaces as per adjoining specification and terminated in and incl sunken pressed steel boxes(min 50 mm deep and 1.6 mm thick sheet) duly painted with anti corrosive paint over a coat of red oxide primer with plastic laminated bakelite sheet top cover 3mm thick make hylum or equivalent fixed with nickel polished screws with cup washers etc including FRLS PVC insulated unsheathed multi stranded copper conductor 1.5 Sqmm single core as earth continuity conductor (green colour) connected with earth dolly with thimble complete all as specified and as directed by Engineer-in-Charge. Note :No more than 06 point on one circuit and separate conduit will be used for power circuit and light point circuit as per NBC code 2016. In addition Electric wiring tests to be carried out in accordance with regulation 1103 & 1104 of regulation for the Electrical equipment of buildings (I E E regulations ,Eleventh edition and as per IE rules 2003 in given format in Annexure I. If resistance of wiring will not meet critaria of IEE regulation contractor will be responsible for that and change in wiring will be executed without extra cost. (ii) Neccessary testing like IR test, Earth leakage test ,etc as per format given by the EIC shall be tested in presence JE E/M and neccesary data to be submitted to this office.
M&L for wiring of circuit/ submain wiring 2 X 2.5 sq. mm + 1 X 2.5 sq. mm earth wire of FRLS PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit of suitable dia complete all as required .NOTE:-2 runs of 2.5sqmm copper conductor and 1 run of 2.5sqmm copper conductor earth wire and 1 run of PVC conduit shall be measured as on unit
M & L MCB DB SPN sheet metal enclosure with category of protection double door type IP-42 factory made with tinned copper 200 Amps rated bus bar suitable for MCBs,single pole and neutral,240 volts 8 way including taking out old one
M& L MCB single pole and neutral 40 Amps working on 240 volts 50 Hz AC supply,10 KA C series including taking out old one.
Supply and fixing 5A to 32A rating , 240, 10 ka 'C' curve MCB suitable for inductive load of SP complete with connections , testing and commissioning etc all as specified and directed.
Supply and fixing 3 modular size GI box with modular plate and cover in front on surface of in recess, including providing and fixing 6 pin 5/6 & 15/16A modular socket outlet and 15/16A modular switch, connections etc as required complete all as specified and directed
Supply and fixing 3 pin, 5A ceiling rose on the junction box including connections etc as required complete all as specified and directed
Supply only LED tube light fitting with tube rod, 20 Watt, 4 feet long, with high lumen output, IP 20 protection, environmental friendly, energy efficient LED, electrical efficiency > 85%, system efficacy > 100 lm/W, operating voltage between 140 - 270 V, AC, 50 Hz, TDH, 10%, power factor ≥ 0.95, surge protection 2.5 kV, colour temperature 5700 K, CRI > 80, with integral drivers, BIS certified with R number, prewired and connecting with 3 core 1 sq mm sheathed copper flexible cable, complete all as directed by Engineer-in-charge.
Supply and fix ultra modern recessed mounting luminare full open 2 x 2 tile , Glare free uniform illumination with longer life and less maintenance 42 W. Make :Crompton CAT LCTLRNE 36 FO CDL or equivalent approved model complete with 3 core sheathed copper flexible 1 sqmm wire upto light fitting and PVC connector complete all as specified and as directed.(80 Light with sub main, 4 light with point wiring)
Earthing with G.I. earth plate 600 mm X 600 mm X 6 mm thick including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe of 2.7 metre long etc. with charcoal/ coke and salt as required.
Providing and laying earth connection from earth electrode with 6 SWG dia G.I. Wire in 15 mm dia G.I. pipe from earth electrode including connection with G.I. thimble excavation and re-filling as required.
Supply & laying in trenches or fixed to wall/pole or passing through pipe cable LT 1100 volts grade heavy duty,XLPE insulated , armoured heavy duty electric cable , with alumn conductor of size 10Sqmm and 4 core including taking down.all as specified and directed by Engineer-in-charge.
Supplying and laying of Telerex DWC (Double wall corrugatred) armoured HDPE pipe ISI marked of outer dia of 77 mm and inner dia of 63 mm polythlene with smooth internal and profiled external surface for non pressure underground cable incl couplers & bens complete all as specified by EIC. Make: Rex Polyextrusion Ltd or equivalent as approved.
Supply, Installation, Testing and Commissioning of 1200 mm sweep,BEE 5 star rated, ceiling fan with Brush Less Direct Current (BLDC) Motor, class of insulation: B, 3 nos. blades, 30 cm long down rod, 2 nos. canopies, shackle kit, safety rope, copper winding, Power Factor not less than 0.9, ervice Value (CM/M/W) minimum 6.00, Air delivery minimum 210 Cum/Min , 350 RPM (tolerance as per IS : 374-2019), THD less than 10%, remote or electronic regulator unit for speed control and all remaining accessories including safety pin, nut bolts, washers, temperature rise=75 degree C (max.), insulation resistance more than 2 mega ohm, suitable for 230 V, 50 Hz, single phase AC Supply, earthing etc. complete as required.
Please Enable Macros to View BoQ information
stage.html
html • 0.04 MB
tech_eval.pdf
boq_comp_chart.xlsx
xlsx
fin_eval.pdf
Tap a document below to read it instantly. You can also download everything as a ZIP if you prefer.
details.html
html • 0.03 MB
Tendernotice_1.pdf
PDF • 0.21 MB
8444_Tender.pdf
Tender Documents • 1.09 MB
BOQ_836157.xls
BOQ • 0.53 MB
Download all tender documents and submit your bid