SPECIAL REPAIR TO BLDG NO P-188 AND PROVN OF 01 X PARKING SHED NEAR BLDG NO -358 UNDER MIL STN RATNUCHAK UNDER GE KALUCHAK

Amount

Taking down cement plaster on brick or stone walls etc including raking out joints, hacking for key, scrubbing down with water etc all as specified and directed.

Demolition of (un reinforced) cement concrete of any description and in any position not otherwise specifically provided for all as specified and directed.

Demolition of stone slabs and tiles of any description or thickness in floors etc laid, bedded and painted in any mortar complete all as specified and directed

Demolition of cement concrete (reinforced) in roofs, floors (other than ground floors), beams, staircases, landing, chajjas and similar suspended work complete all as specified and directed.

Demolition of brick work or stone boulder masonary built in cement mortar complete all as specified and directed.

M&L for Rendering 15 mm thick in cement mortar 1:4 on brick work or concrete surfaces of walls mixed with water proofing compound ISI marked @ 3% by weight of cement as per manufacture instructions furnished even and smooth without using extra cement complete all as specified and directed. (WPC shall be measured and paid separately)

M&L for Rendering 15 mm thick in cement mortar 1:6 on brick work or concrete surfaces, finished even and smooth without using extra cement all as specified and directed.

M&L for rendering 10 mm thick using CM (1:3) on ceiling surfaces complete all as specified and directed.

Preparation of newly plastered surfaces of walls and applying two coats of oil emulsion distemper over a coat of priming paint and over a layer of approved wall care putty complete thickness 3 mm on walls all as specified and directed all as specified and directed.

Complete removal of existing treatment of old plastered surfaces of walls and applying One coats of oil bound distemper over a coat of primer after applying approed wall care putty complete thickness not less than 2 mm on walls wall surface complete all as specified and directed.

Preparation of newly plastered surfaces of ceiling and applying two coats of oil emulsion distemper over a coat of priming paint all as specified and directed complete all as specified and directed.

Complete removal of existing treatment of Ceiling surfaces including brooming down or steel wire brushing, scrapping down smoke soot , mould, moss and efflorescent salts, trading oil and greasy spots, and applying one coats of oil bound distemper over a coat of priming paint complete all as specified and directed . Note : The work will be carried out upto double storey builing the rate of scafolding is included for this item also.

Material and labour for complete removal of existing treatment including fascias, cornices etc by scrapping with mechanical wall sander (having mechanical vacuum mechanism) having RPM not less than 1500, sanding pad of 80 Grit having dia of 7"/9" to make the surface free from dust, loose paint and loose plaster to be completely removed by skilled labour and repair of external wall/ chajjas to be done with repair mortar to get even surface including preparation of old surface of wall/ ceiling by filling cracks by Berger Bison Putty/ crack fill paste of Berger Paints or equivalent make and make good smoothen surfae by sand paper and applying two coats of premium acrylic smooth exterior emulsion of approved colour with silicon additive & Color stay Technology, Excellent Dirt Pick up resistance of Berger Paints Ltd or equivalent of other approved make with low VOC less than 50 gram/ litre as per the LEEDS specifications, Anti Algal properties in two coats @ 1.79 ltr (undiluted)/ 10 sqm diluted with water as per manufacturer instructions applied over one coat of acrylic water based exterior grade primer @ 0.9 ltr (undiluted)/10 sqm mtrs diluted with water in 1:1 ratio as per manufacture's instruction and all coats incl primer to be applied with fuly automatic airless spray machine of paint appliaction with a flow speed of minimum 1 ltr per minute having a pressure of 3300 PSI all as specified and directed. Allow 6-8 hrs to dry the surrface in subsequent coats of paint and including necessary scaffolding at any height complete all as specified and directed Make : Berger Paints Weathercoat Long Life Flexo/ Nerolac Paints excel Total/ Asian Paint Apex Ultima/ JK Maximo Ultra Note :-The concerned items should be executed by OEM authorized applicator after signing of MOU (format attached as Appendix 'EF' on page no. 108 of tender documents as per Sch 'A' Note No 19 Page No 17).

Taking down chowkats or frames with shutters (without taking off shutter from the frames) exc. 1.5 sqm & n.exc. 4 sqm each all as specified and directed

Taking down chowkats or frames with shutters (without taking off shutter from the frames) n exc 1.50 Sqm each all as specified and as directed.

S&F for 125x 65 mm Factory made wood polymer composite (WPC) solid door /window/ceosetory windows and other frames or Chowkats comprising of vergin PVC polymer of K value 58-60 (Suspension grade),calcium carbonate and natural fibers ( wood powder /rice husk/wheat husk and non toxic additieves (maximum toxicity index of 12 for 100 grams fa bricated with miter joints after applying PVC solvent cement and screwed with fullbody threaded star headed SS screws having minimum frame density of 750 kg /cum/ screw withdrawal strength of 2200 N (face) and 1100 N (Edge) minimum compressieve strength of 58 N/mm^2, modules of elasticity 900 N/mm^2 and resistance to spread of flame of class A catogary with property of being termite /borer proof ,water/ moisture proof and fire retardent and fixed in position with MS hold fast /lugs /SS dash fasterners of required dia and length complete all as specified and directed. Note:- For WPC solid door /window frames (-) 5mm tolerance in dimensions i.e depth and width of profile shall be acceptable, but no extra payment on this account shall be made.

S&F single extruded Factory made WPC wood (polymer composite) solid door flush door shutter comprising of vergin PVC polymer of K value 58-60 (Suspension grade),calcium carbonate and natural fibers ( wood powder /rice husk/wheat husk and non toxic additieves (maximum toxicity index of 12 for 100 grams) hacing minimum density of 650 Kg/Cum screw withdrawal strength of 1800 N (face) and 900 N (Edge) minimum compressieve strength of 50 N/mm^2, modulus of elasticity 850 N/mm^2 and resistance to spread of flame of class A catogary with property of being termite /borer proof ,water/ moisture proof and fire retardent and fixed in position with stainless Steel butt hinges of required size with necesassary threaded counter sunk S.S Screws complete all as specified and directed.

S&F Factory made glazed and skeleton shutters 35 mm thick, of second class hard wood, open rebated and prepared to receive glass, gauze, etc. (without sash bars), edges of framing plain, chamfered or rounded. fitted with cut and mitred beads for securing glass, etc.; sizes of members of shutters as specified in SSR Part I, Section 8, clause 8.24 (a); supplied and fitted to chowkats, complete all as specified and directed.

S&F Solid PVC door/cup board frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with MS square tube, suppling and fixing in opening complete all as specified and directed.

S&F Factory made solid panel PVC door/cup board shutter 30mm thick (style) consisting of frame made out of M.S tubes for top & bottom rails. M.S frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement or stiles and plain colour PVC sheets for top rail, lock rail and bottom rail on either side and as gap insert for top rail and bottom rail. Panelling of plain colour PVC sheet to be fitted in the M.S frame welded/sealed to the stiles and rails with suitable PVC sheet beading and joined together with solvent cement, suippling and fixing in the frame at site as per specification in SSR Part-I complete all as specified and directed.

S& F Box type steel windows/ Steel ventilator with top hung shutter including hinges , steel peg stay complete all as specified and directed.

M&L PCC (1:3:6) type C-0 (12.5 mm graded aggregate) back filling of chowkats complete all as specified and directed.

Taking down shutter of any description, exceeding 1 square metre and not exceeding 2 square metre each, all as specified and directed.

S&F 18/19mm thick Prelaminated particle board, exterior grade, prelaminated one side with decorative choice lamination & other side balancing white lamination, fixed with nails to timber frame workincluding 3 mm thick teak wood beading in cup bords/kichen cabinets etc complete all as specified and directed.

S &F 40 mm wide flaps Continuous (piano) hinges , mild steel bright finish or electrogalvanised as in cup boards, kitchen cabinat , etc all as directed by Engr. In Charge.

S &F 40mm dia , Cupboard knobs fixed with nut , screw and washer of mild steel , bright finished all as specified and directed.

S &F Hasp and staple 150 mm safety type aluminium anodised with mild steel hinge pin including bolt to hinge plate and fixed with screws complete all as specified and directed.

S &F Aluminium handles cast type, anodised, 150mm size complete, all as specified.

S &F Aluminium alloy, anodised, sliding door bolt 300mm with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy , all as specified.

S &F Aluminium anodised barrel tower bolts of extruded section with 200 mm long bolt, all as specified.

S &F Mild steel stove enameled helical door spring 150 mm size fixed to pressed steel frame/MS frame/wooden chowkhats including necessary welding work etc (if required) complete all as specified directed.

S &F Butt Hinges medium weight cold rolled mild steel of size 100 mm all as specified and directed

S &F Galvanised mild steel wire cloth, 0.56mm nominal dia of wire and average width of aperture 1.18mm and fixed with 2nd class soft wooden / flat iron fillet beadings fixed in doors or windows etc complete all as specified and directed

S &F 3 mm thick figured glass, pin head type and glazing with oil putty or wooden beads, in square n exc. 0.5 Sq m each all as specified and directed.

S&F 3 mm thick sheet glass ordinary quality and glazing with oil putty in squares not exc 0.5 Sqm in each pane complete all as specified and directed.

M & L for preparation of new wooden surfaces over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer all as specified and directed

Dismantling floor, hearth or wall tiling incl cement mortar bedding (but not backing), terrazzo toping and rubbish off the premises all as specified and directed.

M&L for 25 mm thick PCC 1:2:4, type B-0 (using 12.5 mm graded crushed stone agg) as in levelling course of floor etc complete all as specified and directed

M&L for PCC 1:3:6 C-1 (using 20mm graded crushed stone aggregate) as in plinth protection, path ( 75 mm thick ) finished even and fair complete all as specified and directed.

M&L Providing, cement concrete 1:2:4 type B1, using 20mm graded stone aggregate in lintels upto 1..5 m clear span, cills, steps; seismic and other similar bands, plinth courses, string courses, lacing courses, parapets and railings upto 60 cm in height, copings, kneelers, apex stones, bed plates, water troughs and the like including weathering, slightly rouinded for chamfered angles and throating, complete all as specified and directed.

M&L for Non - skid Ceramic joint free tiles 7 to 8 mm thick area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match and including 15 mm thick screed bed or bedding layer of cement mortar 1:4, set and jointed in neat cement slurry and pointed in coloured cement to match the colour of tiles complete, all as specified and directed.

M&L for Coloured glazed Glazed ceramic tiles in vertical surface exceeding 0.18 sqm but not exceeding 0.38 sqm 7 to 8 mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match including 10 mm thick backing coat of cement mortar 1:3 as in dado, skirting, riser of steps etc., set and jointed in neat cement slurry and pointed in white or coloured cement to match the colour of tiles complete, all as specified and directed.

M&L for Non - skid Ceramic tiles light shade 7 to 8 mm thick area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match incl 15mm thick in CM 1:4 screed bed all as specified.

Glazed ceramic tiles in vertical surface 350x 250x 7 mm/ 450X 350X 7mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match including 10 mm thick backing coat of cement mortar 1:4 as in dado, skirting, riser of steps etc., all as specified. Note : Tiling required to be carried out in small patches.

Taking up or down 15 mm bore steel tubing and connections including cleaning for refixing all as specified and directed.

Taking up or down 20 mm bore steel tubing and connections including cleaning for refixing all as specified and directed.

Cutting chasis, pinning in, brick walls, and making good to facing where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sun shades and cutting chasis for concealed water tubing or concealed conduit wiring, etc making good cuttings not exc 10 cm girth all as specified and directed.

Supplying and laying of 20 mm bore CPVC pipes SDR 11 and plain CPVC SDR 11 fittings in trenches ,laid concealed in floor or wall including all fittings suitable for fixing of plumbing fixture complete all as specified

S & F galvanised steel water tubing, 20 mm bore, medium grade, with all fittings, fixed complete to walls, ceilings or laid in floors all as specified and directed.

Refixing old steel water tubing 15mm dia with and including new GI fittings and connected to new or old positions of walls, ceilings, floors etc complete all as specified and directed.

Refixing old steel water tubing 20 mm dia with and including new GI fittings and connected to new or old positions of walls, ceilings, floors etc complete all as specified and directed.

S&F in repair fancy type CP Bib tap 15 mm long body of cast copper alloy with capstan head, fancy type handle, screwed down for iron pipe, fixed in repairs, complete all as specified and directed.

S&F in repair 15mm pillar taps, fancy type cast copper alloy, with capstan heads, fancy type chromium plated, screw down high pressure with long screwed shanks and fly nuts, screwed for iron pipes ,fixed in repairs complete all as specified and directed.

S&F in reair fancy type, chromium plated angle valve 15 mm of cast copper alloy with crutch handle, screwed down for iron pipe ,fixed in repairs complete all as specified and directed.

S&F in repair fancy type, chromium plated Stop cock 15 mm of cast copper alloy with long shank and cup (concealed type), screwed down for iron pipe ,fixed in repairs complete all as specified and directed.

S&F in repair PVC connection 15 mm size, 600 cm long fitted with PTMT nuts with washer on both ends, fixed to 15 mm bore iron pipes complete all as specified and directed.

Vitreous china wash hand basin, white, flat back, size 580 x 450 mm incl C.I. brackets,CP coupling and 32 mm dia PVC waste pipe, including cutting for and pinning in ends of brackets or erecting stand etc., complete, all as specified and directed.

S & F in repair vitreous china wash down water closet pan (Pedestal pattern) and trap (excluding) fixing bolts,flushing cistern and flush pipe including connection to drain (or outgoing pipe) including plastic seat cover suitable for water closet pedestal pan, coloured closed pattern with flat bottom and cover and mid steel chromium plated or aluminium hinges devices with and including brass chromium plated standard quality jet with nozzle 1500 mm long PVC pipe etc complete all as specified and directed complete all as specified and directed.

PVC valve less syphonic action type flushing cistern 10 liters capacity, low level, white with inlet ball valve float and handle including brackets fixed in repairscomplete all as specified and directed.

Taking up cast iron water mains (including all fittings), with spigot and socket ends and lead or cement joints including burning out joints and recovering complete including disconnecting pipes of any dia all as specified and directed .

S & F 110 dia PVC soil waste , and vent pipe in any length with rubber rings joint fixed to wall/laid in floors complete all as specified and directed.

S & F 75 mm dia PVC soil waste , and vent pipe in any length with rubber rings joint fixed to wall/laid in floors complete all as specified and directed.

S & F in repairs 110 mm dia PVC (SWR) bends, of and radius with access door complete all as specified and directed.

All as per item above above but 75mm dia ditto

S & F 110 mm dia PVC vent cowl fixed in repairs complete all as specified and directed.

S& F as in repair PVC (SWR) floor trap 75mm dia plain with grating including jointing to waste pipe fixed in PCC 1:2:4 type B1 complete all as specified and directed.

S& F as in repair PVC (SWR) branch piece (Single Y etc) equal or unequal 110 mm dia with access door complete all as specified and directed.

S & F of 110 mm bore PVC (SWR) junction double, (single ‘T’) equal or unequal complete all as specified and directed

S & F of 110 mm bore PVC (SWR) junction double, (Double ‘T’) equal or unequal complete all as specified and directed

Ditto all as per item above but 75mm dia ditto

S & F 75 mm bore PVC (SWR) bends of any radius complete all as specified & directed.

S & F 110 mm bore PVC (SWR) bends of any radius complete all as specified & directed.

S&F 20 mm dia powder coated curtain rod in one length per door/window, fancy type (engraved rods) designed & colour as per approved by GE, provided with side golden globe and bracket on each end, fixed in repairs, complete all as specified and directed

M&L for preparation of new steel surfaces over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide primer all as specified and directed

S&F for Soap dish,, fixed to plugs with chromium plated brass screws, fixed in repair complete all as specified and directed

S&F in repair plastic water closet seat, black, closed pattern with flat bottom, and cover and mild steel chromium plated or aluminised hinging device complete all as specified and directed.

M&L machine cut Kota stone slab 15 to 18 mm thick as in flooring or trades of step incl half round moulding over and including screed bed 20 mm thick in CM (1:3) laid & jointed with grey cement slurry mixed with pigment to match the shade of the slab including cutting, rubbing and polishing complete all as specified and directed.

M&L machine cut Kota stone slab 15 to 18 mm thick as in riser to step including 10 mm thick rendring in CM (1:3) laid & jointed with grey cement slurry mixed with pigment to match the shade of the slab including cutting, rubbing and polishing complete all as specified.

Factory made precast concrete designer paver tiles of diferent colour& shape of size 300mm x 300mm x 20mm laid and jointed with grey cement slurry with pigment to match colour of tile ,laid over screed bed or bedding layer. compressive strengfth not less than 250 kg /sqcm complete all as specified and directed. Note :Screed bed /bedding laying shall be measured and paid separately

M & L for PCC 1:4:8 type D2( 40 mm graded aggregate ) as in sub base to flooring 75 mm thick complete all as specified and directed.

M&L for providing and laying 80mm thick factory made chamfered edge cement concrete paver block of M-30 grade with approved colour, design & pattern as in footpath, parks, lawns, drive ways or light traffic parking etc., of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over and including 50mm thick compacted bed of coarse sand, compacting and proper embedding/ laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with fine sand and cutting of paver block as per required size and pattern, finishing and sweeping extra sand, complete all as specified and directed.

M&L for plain cement concrete 1:2:4, type B-1 (using 20mm graded stone aggregate) as in benching, water troughs and the like including form work and finishing all exposed surfaces of concrete, complete all as specified directed.

S&F Rotational moulded polyethylene water tank (cylindrical vertical closed top) hoisted and fixed in position capacity of tank 500 ltrs and S&F 20 mm bore PTMT Ball valve high pressure with exposy coated aluminum rod and high density plastic ball screwed for iron pipe including dismantling of existing water tank of any description .

PCC 1:2:4 type B-0 (using 12.5mm graded crushed stone aggregate) finished even and smooth as in roof padding complete all as specified and directed.

Complete removal of existing roof treatment or roof tile and removing from site to a place outside defence land as specified by civil authorities and clean the surface of roof with water and remove dust complete all as specified.

Cleaning of the exposed concrete slab and repairing the surface irregularities like cracks, potholes, as per manufacturer's method statement by using Berger HS Rapairo(or equivalent)along with HS Latex Plus(or equivalent)& cement in mixing ratio of 1:4 where ever required

M&L for Home Sheild PU Roofkoat (or equivalent) is a one component liquid, solvent free, cold applied water-proofing membrane that is highly elastic and UV resistant with 10 years warranty. ASTM D 6083-97 a waterproofing and heat reflecting system having following key performace properties : 1. UV resistant, prevent yellowing and weathering 2. Highly elastic upto 350% and crack bridging 3. Excellent adhesion on porous and non-porous substrates 4. Tensile strength > 10 N/mm2 with Geo Textile fleece 5. Soler reflective Index (SRI) more then 109-111 ASTM E 1980-11 System : First coat : Providing and applying primer over the prepared surface with HS PU roofkoat Primer (or equivalent) Coverage :0.2kg/m2 (with 50 % dilution of water) Reinforcement : Geotextile 40 gsm Second coat : Home sheildroofkoat (or equivalent) Consumption : 0.5 kg/m2 Third coat : HS PU roofkoat (or equivalent) Consumption : 0.8 kg/m2 System buildup-1.5kg/sqm with geotextile of 40 gsm For accessible roof, tiles with scred/ adhesive may be fixed thereafter. Note :-The concerned items should be executed by OEM authorized applicator after signing of MOU (format attached as Appendix 'GH' on page no. 112 of tender documents as per Sch 'A' Note No 19 Page No 17). Non uploading of MOU by the bidder shall lead to rejection of bid during technical evaluation.

M&L for sunken treatment with glass fiber reinforced modified cementitious coating system before the final coat of Latex Shield 2K (or equivalent) complete all as following :- Base Coat : Berger HS Latex plus (or equivalent) consumption base coat : 0.3 kg/m2 Reinforcement : Glass fiber Second and Third coat : Latex sheild 2K (or equivalent) Consumption top coat : 3 kg/m2 System reqquirements : density : 2.00 kg/ltr; Compressive strength: 0.5N/mm2 Wall penetration through the RCC slab must be sealed using Berger HS Repair (or equivalent). Intersection of base slab with wall must be provided with a 50 mm fillet using Berger HS Latex plus (or equivalent) modified mortar with a bonding coat of Berger HS Latexplus (or equivalent) modified cement slurry upto sft. All depressions, unevenness, surface honeycombng shal be repaired using Berger HS Latex plus (or equivalent) modifiled polymer mortar with a bonding coat of Berger HS latex plus (or equivalent) modified cement slurry. Including cleaning of RCC surface to remove dust, loose paricles, etc with compressed air or any other suitable technique depending on site conditions, grinding aby sharp edges, etc. Note :-The concerned items should be executed by OEM authorized applicator after signing of MOU (format attached as Appendix 'CD' on page no. 104 of tender documents as per Sch 'A' Note No 19 Page No 17).

M&L rendering 10 mm thick on fair faces of brick work or concrete surfaces in CM 1:4 with water proofing compound tobe finished even and smooth without using extra cement complete all as specified and as directed. (WPC to be measured & paid separately)

Supply only Integral water proofing compound liquid complete all as specified and directed.

S&F 20mm dia High density polyethylene pipes (HDPE) of pressure rating 6 kgf/cm2 laid in as spout pipes to pour out rsidual water out from the treated area complete all as specified and directed.

Excavation in trenches, not exceeding 1.5 M wide and not exceeding 1.5 M depth for foundation, etc., and getting out in soft/ loose soil complete all as specified and directed.

-ditto- all as per item No 95 above but depth exc 1.5m but n.exc. 3.00m.

M&L for Plain cement concrete type D-2 1:4:8 (40 mm graded aggregate) in foundation, filling and mass concrete and sub base complete all as specified and directed.

M & L for brick work with sub class ‘B’ old size bricks straight or curved on plan exc. 6.00 m mean radius built in cement mortar 1:6 complete all as specified and directed.

M&L for old size brickwork with sub class ‘B’ bricks in one brick thick honey comb walling, built in cement mortar 1:6 complete all as specified and directed.

M&L loose filling with broken bricks 80 to 150 mm in soakage wells complete all as specified and directed.

M&L of reinforced cement concreteType B1 1:2:4 (20 mm graded aggregade)Nominal Mix as in slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like complete all as specified and directed.

M&L for rolled section as in framing for cladding, glazing, man hole frame and the like fixed with angle cleats and connecting plate, etc with Fe-410-W (Gde E-250) quality 'A' complete all as specified and directed.

M&L for precast reinforced cement concrete 1:2:4 type B1 (using 20 mm graded stone aggregate) as in landings, cover slabs (for manholes etc) shelves and similar articles with plain faces and set in cemnet mortar 1:4 complete all as specified and directed.

M&L for form work to soffits of suspended slab such as roof slabs, floor slabs, landings and similar work n exc 200 mm thick (Horizontal or sloping) flat rough finished surfaces complete all as specified and directed.

M&L for form work to surfaces of walls, baffle walls and similar work vertical or to batter rough finished surfaces of flat concrete surfaces complete all as specified and directed.

M&L TMT steel bars 10 mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed.

M&L reinforced concrete pipes class NP2 with one collar per lenth of pipe 150 mm bore

M & L for PCC 1:4:8 type D2 (using 40 mm graded stone aggregate) in concrete bed to drain pipes including packing under and haunching against the sides of pipes after they are laid and tested for pipes of 150 mm bore complete all as specified and directed.

M&L for forming fair finished drain or channel 30 cm innner girth in cement concrete unsing extra cement including forms, moulds mitred/stopped ends etc complete all as specified and directed.

M&L for Returning filling in, including spreading, leveling, watering and well ramming in layers not exceeding 25 cm in soft/loose soil

Removing excavated material exc 250 m but n.exc 500 m and depositing where directed in soils

M&L for capilary rise treatment of walls as following :- Base coat: Berger HS Latex plus (or equivalent) Consumption base coat: 0.3 kg/m2 Second and Third coat: Latex sheild 2K (or equivalent) Consumption top coat: 3 kg/m2 System requirements: density: 2.00 kg/ltr Compressive strength: 0.5 N/mm2 Note :-The concerned items should be executed by OEM authorized applicator after signing of MOU (format attached as Appendix 'AB' on page no. 100 of tender documents as per Sch 'A' Note No 19 Page No 17).

M&L for taking down cement plaster and decayed concrete of any description, upto double storey of building, from roof projection, chajjas etc and making good the decayed portion with cement mortar 1:3 mixed with water proofing compound or mixed with WPC or PCC 1:2:4 type B-0 (using 12.5mm graded aggregate) including necessary form work, fixing of GI wire netting 0.90mm dia and 12mm mesh in patches area n.exc 5.00 Sqm where ever required and finally finishing the surface with 15 mm thick cement plaster in CM 1:3 and applying two coats of white wash/colour wash/cement base paint/exterior emulsion paint to match the existing surface /finish, complete all as specified and as directed.

M&L Excavating in post holes (or for similar work) each n exc 0.5 cum, getting out, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25 cm in hard/dense soil all as specified and directed by Engr-in- Charge

M&L PCC 1:3:6 type BC2 (using 40mm graded stone aggregate) as in foundation filling and mass concrete in foundation concrete of posts complete all as specified and directed.

S&F structural tubular steel works as in post roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats ,shop coat of primer etc. complete all as specified and directed.

S&F pre- painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and directed.

M&L for preparing surface of new steel material of any description and girth, not otherwise described and treated with two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and directed.

E/M Portion

Taking out carefully copper/aluminium point wiring,Light,fan,socket or power complete with all fitting, fixtures such as switch socket out let, ceiling rose ,holder ,regulator,DBs etc including making good the disturbed surface of wall/floors complete all as specified and directed.

Taking down distribution boards/wooden board ,switch fuse units,steel enclosures for MCB of any type and removing from site complete all as specified and directed.

Taking down ceilling fan/exhaust fans and deposite to MES store yard from site complete all as specified and directed.

Taking down existing unserviceable submain wiring any size and making good the disturbed surface complete all as specified and directed.

Material and labour for point wiring for one light controlled by one way switch with 1.5 Sqmm PVC insulated unsheathed single core multi-stranded copper conductor (FRLS) cable 1100 Volts grade drawn through and including rigid non metallic PVC concealed conduit (medium grade) of suitable dia along with 1.5 sqmm continuous PVC insulated unsheathed single core multi-stranded copper conductor (FRLS) cable for earth continuity wire, connected to earth dolly and to be terminated in and including pressed steel sunken boxes , readily available (Having wall thickness not less than 1.22 mm for boxes upto a size of 200 mmX300 mm and beyond that the wall thickness shall be not less than 1.63 mm) concealed type for mounting of modular switches, sockets, fan regulators alongwith modular plate etc including testing on completion complete including cutting chases for concealed conduit pinning in making good to facing and pointing in using cement mortar 1:3 and making good disturbed surface all as specified and as directed.

All as per item No 125 above but for one fan point controlled by one piano switch complete all as specified and directed.

All as per item no-125 above but for one bell point controled by one bell push complete all as specified and directed.

All as per ser item No 124 hereinbefore but for one 3 pin socket outlet 5 Amp Same board complete all as specified and directed.

All as per ser item No 125 hereinbefore but for one 3 pin socket outlet 5 Amp independent complete all as specified and directed.

All as per Item no 125 here-in-before but for one15 Amp 3pin switch socket outlet, independent with 2.5 Sqmm single core multi-stranded copper conductor cable (FRLS) along with 2.5 sqmm continuous PVC insulated unsheathed single core multi-stranded copper conductor (FRLS) cable for earth continuity wire all as specified and as directed.

Supply and fix modular type switch, one way 6 Amps , 1 module complete complete all as specified and directed.

Supply and fix modular type switch, one way 16 Amps, 1 module complete all as specified and directed.

Supply and fix modular type socket 5 pin, 6 Amps 2 module complete all as specified and directed.

Supply and fix modular type socket 5 pin, 6 A/16 Amps 2 module complete all as specified and directed.

Supply and fix in repairs of Ceiling rose surface bakelite three terminals 240 volts complete all as specified and directed.

Supply and fix in repairs Lamp holder PVC case body of Bakelite with back plate suitable for batten fittings , complete all as specified and directed.

S&F LED Bulb cool white 10 Watt Elegant design direct fit for easy installation complete all as specified and directed.

Supply and fixing Bell push flush type piano 5 Amp complete, complete all as specified and directed.

Supply and fixing Bell multi music 230 volt ,AC single pole complete all as specified and directed.

Supply and fixing of Tube light fitting integrated type suitable for LED 20W indoor decorative aluminium extruded LED batten complete with hosing with all accessories pre wired and making connection with three core copper flexible cable of size 23/0.0076 from ceiling rose to PVC connection to light fitting complete all as specified and directed.

Supply and fixing of Tube light fitting integrated type suitable for LED 10W indoor decorative aluminium extruded T5 LED batten complete with hosing with all accessories pre wired and making connection with three core copper flexible cable of size 23/0.0076 from ceiling rose to PVC connection to light fitting complete all as specified and directed.

Supply and fix in repairs factory made epoxy powder coated Distribution board VTPN 6 ways ,415 Volts with metal door (IP-54 protection) fabricated from minimum 1.6mm thick CRCA sheet and fixed flush to wall and suitable for universal mounting and including 100 Amp copper bus bar, neutral bar, standard DIN rail, Earth bar and cable ties for cale management, top and bottom removable gland plates with Knockouts and suitable for one MCCB as incommer and SP MCBs outgoing confirming to IS : 8623 complete all as specified and directed.

Supply and fixing factory made epoxy powder coated Distribution board SPN 8 ways (SPN MCB DB) with metal door (IP-54 protection) fabricated from minimum 1.6mm thick CRCA sheet and fixed flush to wall and suitable for universal mounting and including 100 Amp copper bus bar, neutral bar, standard DIN rail, Earth bar and cable ties for cale management, top and bottom removable gland plates with Knockouts and suitable for one SPN/DP-MCB as incomer and SP MCBs outgoing confirming to IS : 8623 complete all as specified and directed.

Supply and fixing MCB SP-06 to 32 Amp,10KA, 240 volts complete all as specified and directed.

Supply and fixing of MCB SPN 32 Amp, 240 volts 50Hz AC supply, complete all as specified and directed.

S&F in repair MCCB 415 Volt16 KA 4 Pole 125 Amps complete all as specified and directed.

Material and labour for sub main wiring with two single core PVC insulated (unsheathed) multi strand copper conductor FRLS cable of size 6 sqmm and one single core PVC insulated (unsheathed) solid copper conductor FRLS cable of size 6 sqmm as in continuous earth wire drawn into and including concealed PVC conduit medium grade 25mm dia ISI marked complete with fittings and fixings accessories complete and including cutting chases pinning in making good to facing and pointing in using cement moter 1:3 and making good disturbed surface complete all as specified and as directed.

All as per item no- 147 here in above but 4x10.0 sq. Mm +1x10.0 sq. Mm earth wire

M & L for earthing complete with galvanized steel earth plate 600x600x6mm thick buried vertically in ground to depth not less than 2.25 mtr below ground level, with top edge of the plate not less than 1.50 mtr below normal ground level, connected to GI earth lead wire 4 mm dia by means of bolts, nuts, check nuts and washers of galvanized iron and connection to main switch board of panel, including watering pipe GI 20 mm bore light grade 15mm bore for earthing lead, wire mess, funnel, salt, charcoal dust, excavation and refilling pit with PCC 1:2:4 type B1(using 20mm dia stone aggregate) reinforced with 6mm dia round bar @ 75mm cement concrete both always with MS handle 12mm dia and frame all as shown in electric plate No 3 in page 497 of SSR Part I (2009) and pouring extra Clay Soil of qty not less than one cubic meter into the earth pit and also removal of excavated soil not less than 50 mtr from the earthing place all as specified and directed and tested on completion. including testing complete all as specified and directed.

Supply and fixing LED Bldg security light fitting 35 Watt 230 V AC outdoor type with high pressure die cast aluminum hosing and heat resistant complete with driver, lamp bracket with suitable size and length of 1.5 sqmm copper conductor with impact and corrosion resistant including thermal management in multiple optics complete with IP 65/66 protection complete all as specified and directed.

M&L for cutting of suitable size of holes for 300 mm exhaust fan in wall and grouting of nuts and bolts in wall and making good to match with existing walls all as specified and directed by Engr-in-Charge.

Repair and Fixing ceiling fans complete with blades, and accessories obtained vide srl Item No-122 above with provision of new Anti suicide Fan Rod (suitable size and length and oiling/greasing of fan with provision of flexiable cable twin core all as reqd at site complete all as specified and directed.

NARESH KUMAR AND COMPANY (BID ID -3466097)

M/S ARUN ANAND (BID ID -3460260)

M/S Shiv Enterprises (BID ID -3460148)

GENESIS INDIA (BID ID -3460208)