Construction of Building 306B (Supply Air Fan Building) at FRFCF project site, Kalpakkam

Amount

Clearing light jungle area, bulb weeds, grass including cutting all unwanted plants, branches, twigs, wild growth etc. complete, and disposing the same 100 metres away manually or burning them without disturbing other areas etc., complete all as directed by the Engineer-in-charge. Contractor must be informed to Engineer-in-charge and prior permission shall be obtained from him for burning the wild growth.

All kinds of soil with depth up to 1.5m below average Ground level and disposing surplus excavated earth up to a lead of 1Km

All kinds of soil with depth exceeding 1.5m but not exceeding 3m below average Ground level and disposing surplus excavated earth up to a lead of 1Km

Supply, fixing and laying bi-axial geo-grids of tensile stength minimum 20kN/m, stiching as per specification at junction, Leveling and laying at site as per drawing and direction by Engineer-in-charge. The required testing for qualification will be carried out by the contractor at his cost. (Payment will be made as per actual measurement at site, laps will also be measured for payment)

Supplying and injecting with approved quality chemical emulsion at the rates and concentrations as per IS 6313-2001 Part II for preconstructional anti termite treatment and creating a chemical barir under and alrond the masonry pits, masonry foundations, wall trenches, plinth filling, junctions of wall and floor, expansion joints, surfaces of RCC works for a depth of min. 500mm from the finished ground level, surrounding of pipes, conduits etc., walls retaining soil above floor level, apron and drain along the perimetr of the building including all byeworks complete as per specification/IS 6313:2001 and direction of Engineer-in-charge. Only ground floor plinth area of the building will be measured for the payment in the following three stages. i) 20% after completeion of the foundations i) 50% after completion of the ground floor flooring iii) 30% after completion of all treatment works including ground floor doors & windows. Work ot be executed by M/s Pest Control (India) or any other approved agency and specified guarantee for 6 (six) years shall be furnished b the tenderer. Payment will be cleared only after submission of Guarantee.

Supplying & placing Filcrete using cement crushed stone sand in proportion of 1:15 at temperature not exceeding 38 deg C for filling at all elevation inclusive of all labour, batching, mixing, transportation, material, compaction, pumping, curing etc all complete as per specification, drawing and as directed by the Engineer In-charge.

Construction of granular sub-bass by providing close graded Material, mixing in a mechanical mix plant at OMC, carriage of mixed Material to work site, spreading in uniform layers with motor grader on prepared surface and compacting with vibratory power roller to achieve the desired density, complete as per clause 401 of MoRT&H specifications for road and bridge works (4th Revision) and as directed by the Engineer-in-charge.

for Grading-I material

Providing and laying plain cement concrete M20 grade using 300 kg/cum of PPC, 20mm maximum size graded aggregates and washed crushed stone sand including mechanical mixing, transporting and placing in required position, ramming, compaction, levelling, curing, shuttering, dewatering if any, complete all as per specification for levelling courses in foundation for walls, footings, floor drains etc., encasing pipes and other required works directed by Engineer-in-Charge complete all as per specifications. Dosage of PCE based admixture as per workability requirment at site conditions. Note: 1. The rate of concrete shall include all labour, equipment, charges for mixing & cost of admixture. Polycarboxylate ether (PCE) based chemical admixture confirming to IS 9103 shall be mixed in fresh concrete and prior permission from engineer-in-charge shall be obtained for dosage and compatibility. 2. Test certificate of cement, procured from dealer/company to be submitted for all cement related works by the Contractor. 3. The rate shall be quoted on the basis of using minimum cement per cu.m. of concrete mentioned below for relevant grade of concrete. Any upward/ downward variation required to obtain the specified strength will be paid for or deducted at the rate of cement specified in Schedule F.

Providing and laying plain cement concrete M20 grade using 300 kg/cum of PPC, 20mm maximum size graded aggregates and washed washed crushed stone sand including mechanical mixing, transporting and placing in required position, ramming, compaction, levelling, curing, shuttering, dewatering if any, complete all as per specification up to a height of 0 to 15m for levelling courses in screed concrete at terrace level, encasing pipes and other required works directed by Engineer-in-Charge complete all as per specifications. Dosage of PCE based admixture as per workability requirment at site conditions. Note: 1. The rate of concrete shall include all labour, equipment, charges for mixing & cost of admixture. Polycarboxylate ether (PCE) based chemical admixture confirming to IS 9103 shall be mixed in fresh concrete and prior permission from engineer-in-charge shall be obtained for dosage and compatibility 2. Test certificate of cement, procured from dealer/company to be submitted for all cement related works by the Contractor. 3. The rate shall be quoted on the basis of using minimum cement per cu.m. of concrete mentioned below for relevant grade of concrete. Any upward/ downward variation required to obtain the specified strength will be paid for or deducted at the rate of cement specified in Schedule F.

Providing and laying cast insitu controlled reinforced cement concrete of specified grade at all levels and lifts mentioned below using 20mm maximum size hard granite machine washed crushed graded stone aggregates and washed crushed stone sand including testings as per QAP, weigh batching, charges for mixing & cost of admixture, mechanical mixing, transporting and placing at all lifts, vibrating, consolidating, 14 days curing and finishing smooth of all exposed faces complete for column footing, columns, lintels, sunshades, gutter slabs, beams, slabs, water tank, machine foundation and all other structural elements including dewatering wherever necessary (Formwork and reinforcement will be paid for separately) all as per specification and all as shown in drawings and as directed by the Engineer-in-charge for all insitu item. Note: 1. The rate of concrete shall include all labour, equipment, charges for mixing & cost of admixture. Polycarboxylate ether (PCE) based chemical admixture confirming to IS 9103 shall be mixed in fresh concrete and prior permission from engineer-in-charge shall be obtained for dosage and compatibility 2. Test certificate of cement, procured from dealer/company to be submitted for all cement related works by the Contractor. 3. The rate shall be quoted on the basis of using minimum cement per cu.m. of concrete mentioned below for relevant grade of concrete. Any upward/ downward variation required to obtain the specified strength will be paid for or deducted at the rate of cement specified in Schedule F.

M30 grade with 380 kg of PPC per cu.m. of concrete upto plinth level

M30 grade with 380 kg of PPC per cu.m. of concrete for all floors

Manufacturing, supplying, hoisting and fixing in position at all lifts, precast units of various patterns and sizes for precast plain solid units, slabs, etc, in controlled reinforced cement concrete of M30 grade using 20mm and below machine crushed graded stone aggregate including making perforations in precast slab as per drawing weigh batching, mechanical mixing, casting, vibrating, finishing of exposed faces, curing, necessary formwork, moulds, transporting and placing at all lifts, preparation of connections, grouting with cement mortar/cement grout wherever needed excluding steel reinforcement complete all as per drawing, specification and as directed by Engineer. Note: 1. The rate shall be quoted on the basis of using 380 Kg. of PPC Cement per cu.m. of concrete. Any upward/downward variation required to obtain the specified strength will be paid for or deducted at the rate specified in schedule F. 2. The rate of concrete shall include all labour, equipment, charges for mixing & cost of admixture. Chemical admixture confirming to IS:9103 shall be mixed in fresh concrete and prior permission from Engineer-in-charge shall be obtained for dosage and compatibility. 3. Test certificate of cement, procured from dealer/company to be submitted for all cement related works by the Contractor.

Providing straightening, decoiling wherever necessary bending, cutting, binding and fixing in position steel reinforcement TMT bars of Fe500D grade steel conforming to IS:1786 and tying with approved annealed binding wire of 1.6mm dia in all reinforced cement concrete work at all lifts, including cost of supplying and fixing the spacer/cover blocks and binding wire complete all as per specification and as directed by Engineer-in-Charge at all lifts. Note: The rate shall be including the cost and testing of reinforcement steel at thrid party NABL lab. The reinforcement steel will be procured from dealers with a test certificate as approved by the department. For further details please see Clause 12 of Section VIII, General Information for Guidance of Tenderers.

Supplying, fabricating, erecting and fixing in position at all levels, centering and shuttering to correct line and levels including strutting, propping, etc., with necessary bracings in all axes to give a stable assembly with provision for making the joints in the shuttering fully leak proof and with provision for fixing coil nuts with tie rods along with suitable channel for lateral supports and for inserts, projecting dowels, anchor bolts or any other fixture, including staging, access and working platforms etc., all complete as specified and directed including dismantling and removing the aforesaid assembly after the concrete attains the sufficient strength to self-support itself without cracking and distortion all as per specification, including all materials and labour complete in all respects at all lifts. The measurement for the formwork will be the actual area of forms in contact with concrete surfaces. Shuttering with plywood panels alone will be permitted.

Providing, supplying, cutting, bending to shape, welding, fabricating, hoisting, placing and fixing in position structural steel members like MS structural embedment's/pipe and sleeves/penetration etc. Using MS angles, channels, I-sections, plates, tees, flats, rounds, MS/CS pipes,square sections etc. including chamfering and rounding off the edges, applying a coat of Red lead paint primer / Zinc chromate primer of approved make and 2 coats of flat oil paint / sythetic enamel paint of approved colour and make, scaffolding and staging required for fabrication as well as erection complete all as per specifications, drawings and as directed by the Engineer-in-charge. Note: Lifting device arrangements if any required also arranged by the contractor at his own cost.

Providing Structural steel work in M.S plain plates and chequrred Plates in Embedded Parts, Trench Covers, Connection plates etc. including cutting, hoisting, fixing in position and applying a coat of Red lead paint primer / Zinc chromate primer of approved make and 2 coats of flat oil paint / sythetic enamel paint of approved colour and make including cost of structural steel Plates, welding all labour charges etc. complete as per drawings and specifications. Structral steel plates to be used shall be of approved make. Note: Lifting device arrangements if any required also arranged by the contractor at his own cost.

Providing, fabricating and fixing hand rail using SS304 grade Stainless Steel pipes, Square sections, plates etc. of approved size and make and quality by cutting to required size, welding, mirror / mat polishing, fixing at site etc. for balcony railing & staircases railing including special sections as per drawings, speciifications complete. A sample to be fabricated and to be got approved by the Engineer-in-charge before starting of work at site.This work to be exceuted through approved specialized agency.

Supplying, providing and laying 200mm thick Cement Concrete block masonry using solid concrete blocks of size 400 x 200 x 100mm manufactured as per IS : 2185 (Part-1) density not less than 1800 kg/cu.m of grade C 4.0 using 20mm down graded aggregates in basement & superstructure at all elevations in cement mortar 1:5 including mixing mortar, hacking closely concrete surface, laying blocks, raking joints, curing etc., with all materials, scaffolding, labour, tools etc., all complete as per drawings, specifications and as directed by the Engineer-in-charge. Reinforcement if provided will be measured and paid under relevant item.

Providing and constructing 100mm thick precast concrete solid blocks masonry wall in cement mortar 1:4 with solid concrete blocks of size 400x200x100mm Grade C (4.0), manufactured as per IS : 2185 (Part-1): 2005 density not less than 1800Kg/cum. at all Elevation including cost of materials, labour charges, scaffolding, curing complete all as per specifications and as directed by the Engineer-in-charge.

Providing plastering to the internal surfaces of brickwork / concrete at all elevations in cement mortar 1:5, 12mm thick including hacking of concrete surfaces with pointed tool, scaffolding, finishing, curing, forming grooves wherever necessary, all as per specifications.

Providing and applying minimum 20 mm thick external Sand faced cement sand plaster in two coats, first coat to be 12 mm thick cement sand mortar 1:4 (1 cement : 4 fine sand) including mixing approved pure acrylic based polymer modified cementations water proofing compound in the proportion recommended by the manufacturer in both the layers, keeping the surface of the base coat rough to receive sand faced treatment. Second coat to be 8 mm thick in cement sand mortar 1:3 (1 cement : 3 fine sand), finishing the surface, by taking out grains or keeping the surface rough to receive finishing work or as required to receive specified architectural external finish, to correct line, plumb and level to external faces of walls, soffits/ceiling if any, independent double legged scaffolding, plastering precast concrete, window sills, RCC cornices, making wattas, drip moulds, pattas etc, curing, cleaning, at all levels, complete all as directed by EIC.

Providing Rough cast plastering 20mm thick at all elevations and levels consisting of 8mm thick rough cast in cement mortar 1:3 using 6mm to 10mm size hard granite stone, over a bed of 12mm thick cement mortar 1:5 for external faces, including scaffolding, curing, providing grooves wherever required complete all as per specification & drawings and as directed by Engineer-in-charge.

Providing F3 finish over concrete surface in cement mortar 1:1.5 (1 part cement : 1.5 part fine sand) including wetting the surface, labours, curing, all materials, scaffolding, at all elevations complete all as per specification and as directed by the Engineer-in-charge.

Providing and fixing chicken-mesh reinforcement of 1.5mm dia steel wire with hexagonal or rectangular openings of 10 to 13mm, fixing using nails, including cutting of required sizes complete all as per specification and as directed by the Engineer-in-charge.

Providing and fixing in position High Density Thermocole having minimum density of 20 kg/cum in expansion joint gap filling, machine foundation, including cutting to required sizes, wrapping with 500 micron thick polyethylene sheet, etc complete

25mm thick Thermocole

Providing and fixing in position upto 200mm thick High Density Thermocole having minimum density of 20 kg/cum in expansion joint gap filling, machine foundation, including cutting to required sizes, wrapping with 500 micron thick polyethylene sheet, etc complete all as per specifications and as directed by EIC.

Supplying, mixing and caulking areas at and around penetrations, Embedded Parts, construction joints, expansion joints and at all locations as specified in the drawings, using approved Bitumastic compound joint sealant including preparation of surfaces and edges, applying appropriate primer, backstop, Tape, masking tapes, supply of necessary tools, equipment, scaffolding, manpower etc. all complete as per specifications drawings and as directed by the EIC.

Providing 50mm thick concrete flooring with metalic concrete hardner topping at all levels and floors consisting of underlayer of 38mm thick cement concrete 1:1:2 (1 part Cement : 1 part Fine aggregate : 2 part Coarse aggregate of 12.5mm and below size) by volume, top layer of 12mm thick 1:2 mix (1 part cement with metallic hardener of Hardonate / Ironite or approved equivalent : 2 parts of stone aggregate of 6mm nominal size by volume) (metallic hardener and cement mixed ratio is 1:4) prepared as per manufacturer's instructions including chipping the concrete surface, finishing, curing, providing aluminium dividing strips, cleaning the surface neatly at the time of handing over the area etc. complete all as per specifications and drawings.

Supplying and laying approved quality Polished Vitrified floor tiles of size (600mmx600mm or 300x300 size) 9 to 10mm thick Kajaria/ Asian/ Nitco or approved equivalent conforming to IS 15622 first quality in pattern / combination as shown in drawing,over 40mm thick bed of cement mortar 1:4, to achieve total final floor finish of 50mm thickness, jointed with neat cement slurry mixd with pigment to match the shade of tiles including all materials, labour, tool etc., complete all as per schedule drawings / specification and as directed by EIC. Note: Sample shall be submitted and got approved by EIC before procurement.

Supplying and laying approved quality Anti-Skid Vitrified floor tiles of size (600mmx600mm or 300x300 size) 9 to 10mm thick Kajaria/ Asian/ Nitco or approved equivalent conforming to IS 15622 first quality in pattern / combination as shown in drawing,over 40mm thick bed of cement mortar 1:4, to achieve total final floor finish of 50mm thickness, jointed with neat cement slurry mixd with pigment to match the shade of tiles including all materials, labour, tool etc., complete all as per schedule drawings / specification and as directed by EIC. Note: Sample shall be submitted and got approved by EIC before procurement.

Providing and laying 50mm thick Indian patent stone flooring and skirting with cement concrete 1:2:4, using 10mm and below size hard broken granite stone jelly including dividing strips, laying in panels, consolidating, curing, rubbing the surface smooth, cleaning the surface neatly at the time of handing over the area complete all as per specifications and as directed by the Engineer.ase etc. complete all as directed by the EIC

Providing, laying and fixing dressed Granite slab 18 mm thick for flooring, counters, pantry of black Granite - Jet black or approved equivalent of uniform colour with machine cut edges, pre-polished and rubbed to smooth mirror finish all to required sizes, design, details and pattern as per drawings, on 32 mm thick, 1:4 cement mortar bedding, fit joined with white cement slurry mixed with pigment to match shade of granite including all finishing, nosing wherever required, line & level, etc. complete at all elevations to the satisfaction of the Engineer-In-charge.

Providing and applying painting Two coats at all levels with Interior grade Acrylic emulsion paint (approved brand, colour and manufacturer) confirming to IS 5411 Part I & II at all elevation to give an even shade including one under coat of suitable primer, applying putty, preparation of the surfaces, grinding, removing laitance, cement slurry, formoil, foreign matter etc., scaffolding, tools, tackles, equipment, materials, labour, etc.., all complete as per manufacturer specifications and as directed by the Engineer-in-charge. Note: Rate includes filling all voids/pinholes in concrete by cement mortar touch up work / minor plastering.

Providing and applying painting Two coats at all levels with Exterior grade Acrylic emulsion paint (approved brand, colour and manufacturer) confirming IS : 5411 Part I & II at all elevation to give an even shade including one under coat of suitable primer, applying putty, preparation of the surfaces grinding, removing laitance, cement slurry, formoil, foreign matter etc., scaffolding, tools, tackles, equipment, materials, labour etc.., all complete as per manufacturer specifications and as directed by the Engineer-in-charge. Note: Rate includes filling all voids/pinholes in concrete by cement mortar touch up work / minor plastering.

Supply and application of 2 or 4 coats of Epoxy paint from approved manufacturer & approved shade and approved colour to interior walls, columns, beams, ceiling gantry platform and as indicated in the drawings upto 24m elevation, including scaffolding, staging and approch ladder etc., including preparation of the surface to be painted, by surface grinding, removing laitance, cement slurry, formoil, foreign matter, open voids, water cleaning, protecting the plate EP's, pipe EP's, closed steel boxes, edge angles with masking tape, applying primer coat, one coat of putty mixed with epoxy, filling all voids/pinholes in concrete by approved wall putty mixed with epoxy, removal of roughness in plastered surface with one or two coat of putty, applying epoxypaint by airless spray gun or roller brush with necessary ventilaton system, exhaust fans for proper release of gas, all materials, tools - tackles, equipment, materials, labour, necessary cleaning equipment, etc,. all complete as per manufacturer specification at all elevations and directed by the EIC. Note: Rate includes following 1. Two or more shade with 250 or 500 micron thickness shall be envisaged in a single wall. 2. Wetfilm thickness and Dry film thickness shall be checked at frequent intervals and as per QA requirements. 3. Rate shall also include preparation of concrete/ wall surface by breaking (if required), chipping, surface grinding and making the concrete surface smooth by cement mortar touch up work / minor plastering as indicated by EIC. 4. Painting in confined areas also envisaged in this item. Embedments / equipments available in the room shall be protected with masking tape or by alternate arrangements.

250 microns Elevation upto 10m height

500 microns Elevation upto 10m height

250 microns Elevation above 10m height

Providing and applying painting Two coats on wood work and other required internal surface at all levels with Synthetic enamel paint (Asian or approved brand, colour and manufacturer) to given an even shade including one under coat of suitable primer, preparation of the surfaces, scaffolding complete all as per specifications and as directed by the Engineer-in-charge.

Providing and fixing 1st quality ceramic glazed floor/wall tiles confirming to IS 15622 of approved make in approved size, shade and colour (as approved by Engineer-in-charge), free from cracks, fissures & flake with straight edges & perfect corners fixed at right angies as per design and pattern required over abed of 20mm thick bed of cement mortar 1:4 (in skirting, risers of steps and dados over 12mm thick bed of cement mortar 1:3), including machine / hand cutting to required size and shape, pointed neatly with white cement mixed with coloring pigment to match colour of tile, properly finished in al respects, curing, cleaning the surface neatly at the time of handing over the area, all materials and labour complete. Note: The sample tile shall be got approved by the Architect/Engineer before procurement.

In Dados and skirting laid over 12mm thick backing in cement mortar 1:3

Providing and fixing VITRIFIED floor tiles in different sizes with water absorption less that 0.08% and confirming to IS 15622 of Marbonite or approved make in all colours and shades in Glossy or Matt or satin finish (as required by Engineer-in-charge) laid over a bed of minimum 20mm thick bed of cement mortar 1:4 (IN Skirting, risers of steps and dados over 12mm thick bd of cement mortar 1:3) including machine/hand cutting to required size & SHape, grouting the joints with white cement mixed with coloring pigment to match colour of tile patterns, curing, cleaning the surface neatly at the time of handing over the area complete all as per drawings and specifications. Note: The sample tile shall be got approved by the Architect/Engineer before procurement.

In Dados and skirting laid over 12mm thick backing in cement mortar 1:3

Providing cement plaster skirting in cement mortar 1:3, 18mm thick finished with a floating coat of neat cement including curing, making uniform height, cleaning the surface neatly at the time of handing over the area all as per specifications and as directed by the Engineer.

Providing and fixing anodized aluminium (Anodised transparent or dyed to required shade according to IS: 1868 Minimum Anodic coating of grade AC 15) work for doors, windows, ventilators and partitions with extruded built up standard tubular sections / Z Sections and other sections of approved make confirming to IS: 733 and IS: 1285 fixed with rawl plugs and screws or with fixing clips or with expansion hold fastners including necessary filling up of gaps at junctions, at top, bottom and sides with required PVC / neoprene felt etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / panelling, C.P brass / stainless screws all complete as per architectural drawings and directions of Engineer-in-charge including providing and fixing hinges / pivots and making provision for fixing of fittings wherever required. (fittings, Glazing and panelling shall be paid for under relevant item). NOTE: 1) The rates for aluminium is inclusive of all fasteners required for fabrication and fixing in the walls. 2) All joints shall be of mittered joints. 3) A long M.S rod threaded at both ends to be provided in all aluminium door shutters in Top & bottom Horizontal members internally connecting Vertical members and fixed with M.S washers & nuts. 4) Only Aluminium members alone shall be measured and paid for.

Supplying and fixing Rolling shutters of approved make as per ISI standards made out of required size of MS Laths interlocked together throughout entire length and jointed together at the end by end locks mounted on specially designed pipes shaft with brackets, side guides and arrangements for inside & outside locking with Push and Pull operation complete including the cost of providing and fixing necessary 27.5 cm long wire springs grade No. 2, and M.S Top cover of required thickness for Rolling Shutters.

Rolling shutters PULL and PUSH type including top hood 1.25mm thick

Extra over the cost of rolling shutters for providing and fixing Motorized arrangements including designing, providing spring less motor, control panels, limit switches, etc of "Swastik" or "Windoors" make or equivalent approved make all as per specification and as directed by the Engineer-in-charge.

Exceeding 10.00 sqm and up to 16.80 sqm in the area

Exceeding 16.80 sqm in area.

Supplying, fabrication and fixing Steel doors with metal frame of size 125 x 65 mm made out of minimum 1.2 mm thick Galvanised steel, frame shall be received in knock down or welded condition with bottom tie rods and corner right angle plates for frame rigidity, minimum 3 nos. anchor bolts on each side, fixed in PCC 1:2:4, Steel flush shutter of 40 mm thick made out of prime quality galvanized steel sheet of minimum 0.8 mm thickness mounted on frame work of ‘C’ channel, filling with insulated spun mineral wool / Honey comb core, providing insulated glass vision panel of size 200 x 300 mm of 6 mm thick toughened glass with sealant in each shutter, with ironmongery as given below / approved. Further include painting using epoxy powder coating technology as per RAL shade complete as per drawing. Payment will be made based on clear structural openings. Door frame shall also be filled with light weight material.

Steel Door Single shutter having accessories for single shutter a) 4 Nos of 125 mm long SS ball bearing heavy duty butt hinges with SS screws, b) 1 No vision panel with 6 mm thick toughened glass c) 2 Nos 300 mm long SS pull handle d) 3 point locking panic bar system with external trim PHA 2000 or equivalent e) 1 No Mortice lock Godrej or equivalent 7 levers with handle on both sides f) Heavy duty hydraulic door closer g) 12 mm dia 300 mm long SS tower bolt with SS screws

Steel Door double shutter having accessories as Emergency door (below items are required in each doors) a) 125 mm long SS ball bearing heavy duty butt hinges with SS screws, b) Vision panel with 200 x 300 mmx 6 mm thick toughened glass c) 25mm dia, 300 mm long SS304, D -type pull handle d) 3 point locking panic bar system with external trim PHA 2000 or equivalent e) Mortice lock Godrej or equivalent 7 levers with handle on both sides f) Heavy duty hydraulic door closer g) 12 mm dia 300 mm long SS tower bolt with SS screws

Providing and fixing 30mm thick factory made PVC door shutters with door frames of approved colour/shade "Sintex / Akrosha" or approved equivalent make and wall thickness 2mm + 0.2mm with inbuilt edging on both sides. The styles and rails mitred and joined at the corners, including all accessories & fittings like 3 nos. 100mm SS hinges, 2 Nos 125mm Grip aluminium Bow handles, 2 Nos of Aluminium 75m Baby latch for each door complete all as directed at by Engineer-in-charge.

Providing and fixing glazing with 6mm thick clear Float glass pane in aluminium doors, windows, ventilator shutters and partitions etc. with Neoprene gasket including cost of neoprene gasket complete as per the drawings and directions of the Engineer-in-charge.

Providing and fixing 12mm thick prelaminated with decorative lamination on both side, 3 layer medium density (Exterior grade) particle board Grade-1, Type - II confirming to IS: 12823 bonded with phenot formaldhyde synthetic resin of approved brand and manufacture in panelling fixed in aluminium doors, window shutters and partition frames with C.P. brass / stainless screws etc. complete as per drawings and as directed by Engineer-in-charge.

Providing and fixing 5mm thick Polypropelene plastic lattice system of approved design, colour and size at all elevations including fixing with Anodized aluminium frame work or other approved frame work, sealing the joints with required sealants, etc., all as per drawing and specification and as directed by Engineer In Charge. (Note: Rate for frame work with Aluminium will be paid for seperately under relevant item)

Supplying and laying Roof insulation for buildings as specified inclusive of surface preparation, labour, tools, equipment, material etc., all complete as per specifications, drawings and as directed by the EIC, consisting of surface preparation a) Laying 50 mm thick Precast light weight foam concrete jointing with CM 1:3. b) Applying 75 mm thick in situ spraying of Polyurethane foam concrete. c) Applying one bituminous layer at the rate of 0.25 kg/sq.m. d) Providing average 50 mm thick screed concrete in N25 to required slope and grading in suitable panels after surface preparation. e) Applying one bituminous layer at the rate of 0.25 kg/sq.m. f) Laying 1st layer of minimum 4 mm thick APP membrane by LPG torch flame. g) Laying 2nd layer of minimum 4 mm thick membrane over first layer. h) Painting one coat of reflective paint over the APP. i) Cutting the wall and tuck in the APP and seal with cement mortar 1.1 added water proofing compound Note: Suitable guarantee for 10 years is to be provided for this work.

Supplying, providing and installing in position for Horizontal/ Vertical expansion joints at interior surface for upto 200 wide joint at different levels with sliding type cover strip using 6 mm thick plain Aluminium plate of 400 mm wide including attaching the fixed edge of the cover strip to the embedded / base plate and providing sliding surface at the free edge including anchor fasteners, screws, scaffolding, staging, labours, materials etc., all complete, as per drawing, specifications and as directed by the EIC.

Horizontal position for floor to floor joint using 4mm thk Aluminium plate

Horizontal position for ceiling beam to beam joint using 4mm thk aluminium plate

Vertical position for Column to Column /wall joint using 2mm thk aluminium plate

Supplying, providing and installing in position for horizontal / vertical Sealed Seismic joints at the exterior face for upto 200 mm wide joint at different elevations for horizontal roof joint, roof joint with corner condition, turn bar, water proof membarane, vertical column joint with compression seal, membrane, sliding type cover strip with minimum of 6 mm thick aluminium sheet, with necessary supporting fastener including attaching the fixed edge of the cover strip, including labours, materials etc., all complete, as per drawing, specifications and as directed by the EIC for the following.

Vertical position for Column to Column / wall joint with minimum 4mm thick aluminium plate

Supplying, mixing and caulking areas at and around penetrations, Embedded Parts, construction joints, expansion joints and at locations as specified in the drawings, including preparation of surfaces and edges, applying appropriate primer, backstop, Tape, masking tapes, supply of necessary tools, equipment, scaffolding, manpower etc. all complete as per specifications drawings and as directed by the EIC using:

Approved Poly sulphide sealing compound for expansion joints

Grouting at and around penetrations, construction joints and at all locations as specified in the drawing including necessary scaffolding, drilling holes of specified diameter, supply of grout material, PVC pipe nozzle, fixing, providing all necessary equipment like mixer and pump, manpower etc., all complete required to grout at specified pressure, cutting the pipes after setting of grout, sealing, finishing the surface to achieve required leak-tightness to the satisfaction of the EIC. Only quantity of grout injected shall be measured and paid for. This item is not intended for repair works falling under the scope of contractor for concreting works.

Using Cement based grouting suitable for pumping with addition of approved anti shrinkage compound @ 2% weight of cement with water reducing admixture as required and as directed by the EIC.

Supplying and placing Normal non shrink / dry pack below equipment, structural steel base plates/bearing plates, penetrations, anchorages, pockets and other areas at all levels, including preparation of surface, roughening of concrete surface by chipping including supply of necessary equipment, scaffolding, labour, compacting, curing, finishing etc., all complete as per drawings, specifications and as directed by the EIC using.

Stiff mix grout 1:1:2 Cement : Sand : Aggregate grout / dry pack with 6 mm down graded stone chips with Shrinkomp 30 or Conbextra GPI or approved equivalent anti-shrink compound with W/C ratio as per manufacturer's specifications and as directed by the EIC.

Providing and fixing IS: 3564 marked AI die cast body tubular type universal hydraulic door closer with necessary accessories and screws etc. in wooden doors / steel doors with necessary bolts & nuts "Everite Hardwyn" or approved equivalent make complete as per specification and as directed by the Engineer-in-charge.

Providing and fixing 150 x 200mm vision panel in door shutter using 4mm thick glass with teakwood lipping of 20x10mm size alround complete all as directed by the Engineer-in-charge.

Providing and fixing ISI marked (IS:205) aluminium butt hinges of size 100 x 63 x 4mm of approved make anodised (anodic coating not less than grade AC 10as per IS:1868) transparent or dyed to required colour or shade with necessary screws etc. complete all as per specification and as directed by the Engineer-in-charge.

Providing and fixing 4 Lever Dead /Mortice Lock 'Godrej/Everite' or other approved equivalent make suitable for aluminium door with a pair of keys complete all as per specification and drawings.

Providing and fixing Stainless steel "C" type Door handles SS 304 Grade solid Rod, 250mm long in Steel Doors / wooden Doors including SS screws / bolts etc. all as per drawings and specifications complete. Sample to be approved by the Engineer-in-charge.

Providing and fixing Stainless steel "C" type Door handles SS 304 Grade solid Rod, 100mm long in Steel Doors / wooden Doors including SS screws / bolts etc. all as per drawings and specifications complete. Sample to be approved by the Engineer-in-charge.

Providing and fixing anodised aluminium tower botts of size 150 x 10mm (Barrel Type) ISI marked (IS: 204) of approved make (anodic coating not less than grade AC 10 as per IS: 1868) transparent or dyed to required colour or shade with necessary screws etc. all as per specifications and as directed by the Engineer-in-charge.

Providing and fixing anodised aluminium tower botts of size 100 x 10mm (Barrel Type) ISI marked (IS: 204) of approved make (anodic coating not less than grade AC 10 as per IS: 1868) transparent or dyed to required colour or shade with necessary screws etc. all as per specifications and as directed by the Engineer-in-charge.

Providing and fixing AI hanging Heavy Quality floor door stopper ISI marked with Twin Rubber stoppers, anodised (anodic coating not less than grade AC 10 as per IS: 1868) transparent or dyed to req. colour or shade with necessary screws etc. complete all as per specification and as directed by the Engineer-in-charge. Sample to be approved by the Engineer-in-charge.

Providing and fixing 250mm long Anodised Aluminium aldrop. Rod thickness 16 mm. The anodic casting shall be not less than Grade AC 10 of IS 1868 : 1982 or as required by the purchaser. with necessary accessories and screws etc. in wooden doors / steel doors with necessary bolts & nuts complete as per specification and as directed by the Engineer-in-charge.

Providing and fixing Swing type heavy quality top PIVOT for suspending aluminium door shutters of single or double leaf all as directed by the Engineer-in-Charge.

Providing and fixing Swing type heavy quality bottom PIVOT for suspending aluminium door shutters of single or double leaf all as directed by the Engineer-in-Charge.

Providing and fixing coloured vitreous china European type water closet with 'P' or 'S' Trap with ISI marked colour solid seat and lid of Hindware or Equivalent approved make, 10 litre low level colour PVC flushing cistern with manually controlled device (handle level) conforming to IS: 7231, Flush bend fixing EWC with C.P. Brass screws, 15mm PVC heavy quality inlet connection of 600mm long, stop cock, including testing, commissioning & cleaning etc. complete all as per drawings and specification and as directed at site.

Providing and fixing white vitreous china flat back half stall urinal size 590 x 380 x 350mm Hindware or Parryware Newmagnum model or Equivalent approved make with PVC 15mm inlet connection, Push cock, 15mm stop cock, C.P. brass spreaders, 32mm Urinal waste coupling with Dome grating, and clamp etc. including making G.I water line connection complete all as per drawings and specifications and as directed at site. (Only G.I. pipes will be paid under relevant item)

Providing and fixing Viterious china white wash basin size 560x410mm / 560x450mm, oval model (HINDWARE / PARRYWARE ) with C.I. brackets, 15mm C.P. brass pillar taps of Jaquar / Parryware or approved equivalent make, 15mm x 600mm long PVC inlet connections, 15mm stop cock, 32mm Heavy quality C.P. brass waste coupling of standard pattern, including painting of fittings and brackets, cutting and making good the walls and testing complete all as per specifications and as directed by the Engineer-in-charge.

Supplying and fixing 32mm heavy quality C.P.Brass Bottle trap / P-trap of make "Jaguar" / "Parryware" or other approved equivalent make with self cleaning design for wash basin all as directed by the Engineer-in-charge.

Providing and fixing 6mm thick Mirrors of size 600 x 460 x 6mm "Modi Guard" or approved equivalent make with bevelled edges complete with 6mm thick asbestos sheet back ground fixed to walls with C.P. brass screws and concealed washers complete all as per specifications and as directed by the Engineer-in-charge

Providing and fixing liquid soap dispenser in PVC container "VEGA" or approved equivalent make with all accessories and CP brackets including necessary screws for fixing complete all as directed by the Engineer-in-charge.

Providing and fixing C.P. Brass towel rail 600mm long of approved make complete fixed to walls with 30mm CP brass screws with concealed fitting arrangement all as directed by the Engineer-in-charge.

Providing and fixing solid state fully hygienic sensor operated Hand drier of approved make rated for continuous repeat usage with solid state time delay LSF protection, with independent ambient level & seasonal control temperatures 230 volts , single phase 50 HZ, 15 Amp and AC supply in multiple stored , multiple grounded steel enclosure powder coated in required shade with one bracket for firm wall fixture, one meter sheathed 3 core flexible cable , 1- three pin 15 Amps plug top etc complete as directed by EIC.

Providing and fixing PVC inlet connection pipes heavy quality suitable for hot and cold including CP brass unions and nuts 15mm dia 600mm long as per specifications and as directed by the Engineer-in-charge.

Providing and fixing Heavy Quality C.P. brass 15mm dia Bib cock "ESSCO / PLATO" or approved equivalent as per specifications and as directed by the Engineer-in-charge. (Sample to be got approved by the Engineer-in-charge)

Providing and fixing Heavy Quality 15mm nominal bore C.P. Brass Angle cock 'ESSCO / PLATO' or approved equivalent make and type as per specifications and as directed by the Engineer-in-charge. (Samples to be got approved by the Engineer-in-charge)

Providing and fixing Heavy Quality 15mm nominal bore C.P. Brass push pull cock (auto release cock) 'ESSCO / PLATO' or approved equivalent make and type as per specifications and as directed by the Engineer-in-charge. (Samples to be got approved by the Engineer-in-charge)

Providing and fixing Heavy Quality C.P. Brass Health Faucet with 1.50 metres flexible hose (Hand Showner) of 'ESSCO / PLATO' or approved equivalent make and type as per specifications and as directed by the Engineer-in-charge. (Samples to be got approved by the Engineer-in-charge)

Providing and fixing 20mm thick white marble stone slab of approved colour and shade, table rubbed, edges rounded and polished of size 750 x 500mm deep (or size as directed by the Engineer-in-charge) fixed in urinal partitions by cutting a chase of appropriate width with chase cutter and embedding the stone in the chase with epoxy grout or with cement concrete 1:2:4, using 6mm nominal size aggregate and finished smooth complete all as per specification and as directed by the Engineer-in-charge

Providing and fixing PVC Nahani trap of Prince / finolex or approved equivalent make conforming to the relevent IS code, heavy quality of self cleaning design with 75mm internal dia and outlet with 125mm dia, PVC grating with perforated holes on top including embedding in cement concrete 1:2:4, forming circular holesby providing and fixing 110mm OD PVC pipes of required height upto floor level, levelling and rendering smooth, making good the floor, and wall etc. all complete as per specifications. (Rate shall include cost of PVC pipe and it shall not be paid extra).

Supplying and fixing of CP Double coat hook of make aguar or other approved equivalent make including fixing, etc., all complete as per specification and as directed.

Providing laying and fixing with uPVC pipe laid /embedded under floor slab and fixed to walls wherever required FINOLEX/PRINCE or other approved equivalent make of UPVC stabilized - SWR PVC pipes - Type B (Suitable for soil and waste discharge system having wall thickness of minimum 3.2 to maximum 3.8mm) conforming to IS - 13592 - Latest edition and PVC pasting type specials such as door bends, door tees and cowls etc. heavy quality for soil waste or vent or anti-syphonage PVC pipe with necessary PVC clips and joints.

50mm OD UPVC pipes and specials.

76mm OD UPVC pipes and specials.

110mm OD UPVC pipes and specials.

Providing and fixing 150mm dia, Cast Iron slotted gratings over the rain water down take pipes at roof including chipping and grouting, painting two coats of anticorrosive paint complete all as directed by the Engineer-in-charge.

Providing and fixing Chlorinated PVC (CPVC) pipes for concealed pipeline work having thermal stability for hot & cold water supply (as ATM Standard 2846 & SDR - 11 Grade) including all CPVC Plain & Brass threaded fittings, fixing the pipe with clamps including chasing the walls, concealing the pipes and making good the same etc. This included jointing of pipes & fittings with CPVC Solvent cement & testing the joints complete all as per specifications, drawings and as directed by the Engineer-in-charge.

20mm outer dia CPVC pipe

25mm outer dia CPVC pipe

Providing, Laying, Jointing, fixing and testing for following diameter of Exposed on wall plumping lines Heavy quality (C-Class) Galvanized Iron pipes of TATA or approved equivalent make and ISI marked fittings like, tees, elbows, bends, unions, nipples, reducers etc. as required for 10.00 kg / sq.cm hydraulic pressure with a minimum period of two hours duration with clean water, including cutting, threading, jointing with hemp yarn, white lead, jointing Teflon tape, fixing in walls / trenches using clamps etc. including 2 coats of Synthetic enamel paint over a coat of primer, complete all as per specification and drawings, all as directed at site. Pipes with exclusive use of ISI marked approved make C-Class pipes

25mm n/b G.I. pipe

40mm n/b G.I. pipe

Providing and fixing the following sizes of gun metal full way gate valves female ends screwed bonnet integral seat non raising spindle class I, ISI marked to IS: 778 tested to 20 kg/sq.cm hydraulic pressure etc. complete all as per specification and as directed by the Engineer-in-charge.

25mm nominal bore

40mm nominal bore

Providing, fixing & jointing the following outer Dia of best quality UPVC rainwater down take pipes as per IS:4985 (with IS mark) with pressure rating of 6 kg/cm2 (Class 3- Green mark) conforming to IS-13392, with ISI mark and heavy duty specials such as bends, junction, tail peace, collars swan necks, shoes etc. including fixing to the wall with adequate no. of standard MS fixing clamps at all elevations all complete as directed by EIC. Note: Masonry support near the shoe to be provided and the same will be measured under relevant items.

Providing and fixing Heavy Quality 'C' Class G.I pipe sleeves 200mm n/b, 450mm long, with puddle Flange of 250x250mm, 6mm thick for rain water down takes (or 200mm dia) to be embedded in RCC slabs / RCC roof Gutters to connect Rain water pipes by welding or with screwed sockets all as per the drawings and as directed by the Engineer-in-charge. These sleeves to be fabricated and embedded at the time of concreting in true vertical.

Providing and fixing Heavy Quality 'C' Class G.I pipe sleeves 150mm n/b, 450mm long, with puddle Flange of 250x250mm, 6mm thick for rain water down takes (or 160mm dia) to be embedded in RCC slabs / RCC roof Gutters to connect Rain water pipes by welding or with screwed sockets all as per the drawings and as directed by the Engineer-in-charge. These sleeves to be fabricated and embedded at the time of concreting in true vertical.

Providing and laying non pressure NP2 class RCC Hume pipes conforming to IS: 458, with collars jointed with stiff mixture of cement mortar in the proportion of 1:2, laying to the levels, slopes including testing of joints etc. complete all as per the drawings and specifications and as directed by the Engineer-in-charge.

300mm dia NP2 class RCC Hume pipe

Providing and constructing Gully Chamber of internal size 300x300mm including providing, supplying and fixing 150 x 150mm stoneware gully trap with CI grating including excavation in all types of soils, backfilling, embedding in plain cement concrete 1:4.5:8 using 40mm size granite aggregates and constructing the above chamber with 115mm thick brick work in plastering over both internal and external faces of brick work with cement mortar 1:3, 12mm thick finished smooth with a floating coat of neat cement on both faces, providing and fixing CI cover with frame of 300 x 300mm size (inside) the weight of cover to be not less than 4.5 kg and frame to be not less than 2.70 kg as per standard design complete all as per specification and as directed by the Engineer-in-charge.

Construction of Inspection chamber of following size internally up to 1.00 metre depth with brick masonry walls of 230/345mm thick using stock bricks in cement mortar 1:5 with necessary brick carbelling as required, plastering with cement mortar 1:3, 12mm thick for external sides of the chamber including excavation in all types of soils, back filling, providing and laying 150mm thick PCC 1:4.5:8 for foundation concrete forming bencing in PCC 1:2:4 using 20mm maximum size graded aggregate etc. complete all as per specification, drawing and as directed by the Engineer-in-charge.

Inspection chamber of internal size 600x600mm

Inspection chamber of internal size 900x600mm

Supplying and fixing in position of heavy quality Cast Iron manhole frame and cover, steps etc of specified weight for the inspection chamber, valve chamber etc. all as per specifications and as directed by the Engineer-in-Charge.

Cleaning the surface of TMT 500D reinforcement of various diameter using wire mesh or equivalent techniques and cement washing using PPC , at all lifts, tools and tackles labour, curing, necessary formwork, transporting, hacking the construction joints complete all as per specifications and as directed by the Engineer-in charge.

supplying providing fixing 25mm thick neoprene sheet of approved quality suitable shape as mentioned in the drawing and specification cost to include preparation of surface, supply of necessary tools, scaffolding,manpower etc,at all level as per drawings,specification, and as directed by the Engineer-in charge.

Supply and Embedment of following sizes of flush mounting POWDER COATED TPN/SPN DB Enclosures with Double Door and per Phase isolation DBs consisting of Phase, Neutral and Earth Bus and interconnecting wires etc. at suitable depth in brick work as per the detailed specification and as directed by the Engineer-in-charge.

TPN, 6 Way Distribution Board Powder coated Per Phase Isolation DBs Per phase Isolation kit with all accessories.

TPN, 8 Way Distribution Board Powder coated Per Phase Isolation DBs Per phase Isolation kit with all accessories.

Supply and Embedment of following sizes of flush mounting POWDER COATED TPN/SPN DB Enclosures with Double Door consisting of Phase, Neutral and Earth Bus and interconnecting wires etc. at suitable depth in brick work as per the detailed specification and as directed by the Engineer-in-charge.

SPN, 12 Way Distribution Board with all accessories Cat No:DBSPN012DD or equivalent make.(For 4 way DCDB)

Supply and installation of following sizes of Heavy Duty, Hot Dip Galvanised MS ERW Conduits for Electrical & Communication System with all the required accessories like round JBs, 40mm Slevees, Solid Long Bends, Check Nuts, Nipples, Couplings, Reducers, Copper Clips, Copper Conductor, GI Wire etc, on roof slab, column, beams etc as per the detailed specification.

25 mm Dia 1.8mm, wall thickness GI Heavy Duty ERW Conduits with 75mm deep junction boxes

40 mm Dia 2mm, wall thickness Heavy Duty ERW Conduits with 75mm deep junction boxes

Supply and embedment of concealed type MS boxes of the following types and as specified in RCC/Brick/Concrete Block Masonry with finishing and making good as per the detailed specification.

150(W)X150(H)X80(D)mm, 1.6mm thick sheet Hot dip galvanised MS box

400(W)X300(H)X200(D)mm, 1.8mm thick sheet Hot dip galvanised MS box

Supply and Embedment of MS fan Hook Boxes in RCC roof slab with finishing and making good as per drawing No:IGC/ESD/9170/8009 and the detailed specification.

Supply and Embedment of 50mm Deep, Square/Rectangular Concealed type and GI double earthed modular metal boxes of the following types and as specified in RCC/Brick/Concrete Block Masonry with finishing and making good as per the detailed specification.

1/2 Module SB

3 Module SB

4 Module SB

Supply, installation and end termination of the 185 Sq.mm tinned, stranded copper conductor embedded in the PCC floors/ RCC floors/ RCC columns and beams/ RCC / Brick Masonry walls etc., installation as per the scope of work and drawings.

Supply and installation of the following size of tinned copper grounding pads embedded in the Cement floors, RCC / Brick Masonry walls/floors/columns/beams/ceiling etc., as per the scope of work, drawings and as directed by the Engineer-In-Charge:65 x 65 x 4 mm tinned copper grounding pads

Supply and installation of Cad Weld Points

Jointing of 185 Sq.mm tinned, stranded copper conductor by exothermic welding (CAD welding) of the Straight type Joint complete with all components and accessories as per the scope of work and drawings.

Jointing of 185 Sq.mm tinned, stranded copper conductor by exothermic welding (CAD welding) of the T- type Joint complete with all components and accessories as per the scope of work and drawings.

Jointing of 185 Sq.mm tinned stranded copper conductor with 65 x 65 x 4 mm tinned solid copper floor/wall/column/ceiling grounding pads

Wiring for lights / fans /sensors/ Power point with 1100V grade FRLS insulated copper conductor wires in existing concealed/ Exposed PVC / ERW / Flo-coated Metal conduits as per the detailed scope of work, including supply of Wires, termination of copper wires at either end by crimping including supply of PVC Sleeves/Ferrules, Copper Crimping Lugs and connecting the wires to various switches, sockets, etc. including testing and commissioning as per the detailed specification.(Refer Sec VI, Clause No.18)

Wiring point for lighting with 2 nos of 1.5sq.mm copper wires for Phase & neutral and 1 no of 2.5sqmm copper wire for earthing from DB to Control switch box (Avg. length - 43 Meters) as per the specification.

Wiring point for lighting with 2 nos of 1.5 sq.mm copper wires for Phase & neutral and 1 no of 2.5sqmm copper wire for earthing looped from Control switch box to control switch box (Avg. length - 16 Meters) as per the specification.

Primary light point with 2 nos of 1.5sq.mm copper wires for Phase & neutral and 1 no of 2.5sqmm copper wire for earthing from control switch box to first Light point (Avg. length - 12 Meters) as per the specification.

Secondary light point with 2 nos of 1.5sq.mm copper wires phase & neutral and 1 no of 2.5sqmm copper wire for earthing looped from Light point to Light point (Avg. length - 8 Meters) as per the specification.

Wiring point for bay lighting with 2 nos of 2.5sq.mm copper wires for Phase & neutral and 1 no of 2.5sqmm copper wire for earthing from MCB at DB to Control switch box (Avg. length - 42 Meters) as per the specification.

Wiring point for bay lighting with 2 nos of 2.5 sq.mm copper wires for Phase and Neutral and 1 no of 2.5sqmm copper wire for earthing from Control switch box to control switch box (Avg. length - 24 Meters) as per the specification.

Wiring point for bay lighting with 2 nos of 2.5sq.mm copper wires for Phase & neutral and 1 no of 2.5sqmm copper wire for earthing from Control switch box to first Light point (Avg. length - 28Meters) as per the specification.

Wiring point for bay lighting with 2 nos of 2.5 sq.mm copper wires for Phase and Neutral and 1 no of 2.5sqmm copper wire for earthing looped from light point to Light point (Avg. length - 12 Meters) as per the specification.

Wiring point for FAN with 2 nos of 2.5sq.mm copper wires for Phase & neutral and 1 no of 2.5sqmm copper wire for earthing from MCB at DB to Control switch box (Avg. length - 42 Meters) as per the specification.

Wiring point for FAN with 2 nos of 2.5 sq.mm copper wires for Phase and Neutral and 1 no of 2.5sqmm copper wire for earthing from Control switch box to FAN (Avg. length - 22 Meters) as per the specification.

DC light point with two no of 2.5 sq.mm copper wires from DC DB to first light point.(Avg. length - 46 Meters) as per the specification.

DC light point with 2 no of 2.5 sq.mm copper wires from light point to next light point (Avg. length - 32 Meters) as per the specification.

Wiring for lights / fans /sensors/ Power point with 1100V grade FRLS insulated copper conductor wires in existing concealed/ Exposed PVC / ERW / Flo-coated Metal conduits as per the detailed scope of work, including supply of Wires, termination of copper wires at either end by crimping including supply of PVC Sleeves/Ferrules, Copper Crimping Lugs and connecting the wires to various switches, sockets, etc. including testing and commissioning as per the detailed specification.(Refer Sec VI, Clause No.18)

Primary power points: 2 nos of 2.5 sq.mm copper wire for phase and neutral and 1 no of 2.5sqmm copper for earthing wire from MCB at DB to Control switch and Socket (Avg.length - 46Meters) as per the specification.

Secondary power points: 2 nos of 2.5 sq.mm copper wire for phase and neutral and 1 no of 2.5sqmm copper wire for earthing from control switch and socket to control switch and socket (Avg. length - 28 Meters) as per the specification.

Wiring for lights / fans /sensors/ Power point with 1100V grade FRPVC insulated copper conductor wires in existing concealed/ Exposed PVC / ERW/Flo-coated Metal conduits as per the detailed scope of work, including supply of Wires and termination of copper wires at either end by crimping including supply of PVC Sleeves/Ferrules, Copper Crimping Lugs and connecting the wires to various switches, sockets, etc. including testing and commissioning as per the detailed specification.(Refer Sec VI, Clause No.18)

Primary points: 2 nos of 4 sq.mm copper wire and 1 no of 2.5sqmm copper wire from DB to Control switchs (Avg. length - 38Meters) as per the specification.

Secondary points: 2 nos of 4 sq.mm copper wire and 1 no of 2.5sqmm copper wire from Control switchs to Sockets (Avg. length - 2.5 Meters) as per the specification.

Supply and Installation of following Wiring Accessories as per the detailed specification (Refer Sec VI (MNC), Clause No.5).

Supply, Installation, Testing and Commissioning of 1No Socket 10-25A , 3 Pin combined shuttered type Socket on modular plate and termination of wires to the switches for split ACs as per the specification.

Supply, Installation, Testing and Commissioning of 1 No 20 Amp Motor starter Switch on modular plate and termination of wires to the switchesr for split ACs as per the specification.

Medium bay luminaries:Supply, installation, testing, and commissioning of energy-efficient medium bay industrial type LED luminaries of suspended type with CCT of 6500K, variation in CCT within 7 steps, having a minimum CRI of 80, lumen output of minimum 9200, minimum lumen efficiency of 110 lm/w, ingress protection min of IP20, and impact resistance of min IK-05 having THD of less than 10% in pressure die-cast aluminum housing, etc., with a suitable current control driver circuit and complete with all accessories including mounting arrangements required to suspend a fitting from a 9 meter medium bay with provision and connection for 4 sq. mm flexible copper conductor of PVC insulation wire, etc., as per specification and as per the instruction of EIC.

Wall mounted/Suspended type luminaries:Supply, installation, testing, and commissioning of energy-efficient Wall mounted/Suspended type industrial LED luminaries with CCT of 6500K, variation in CCT within 7 steps, having a minimum CRI of 80, lumen output of minimum 4000, minimum lumen efficiency of 110 lm/w, ingress protection min of IP20, and impact resistance of min IK-05 having THD of less than 10% in pressure die-cast aluminum housing, etc., with a suitable current control driver circuit and complete with all accessories including mounting arrangements required to mount on wall /suspended from 5 meter ceiling with provision and connection for 2.5 sq. mm flexible copper conductor of PVC insulation wire, etc., as per specification and as per the instruction of EIC.

Wall mounted DC luminaries:Supply And Installation, Testing, And Commissioning of 1x9W DC fed clustered led fitting on the wall as per specification and as per the instruction of EIC.

Supply And Installation, Testing, And Commissioning of 1x7W(Min.) 230V AC fed clustered led fitting on the wall suitable for washrooms as per specification and as per the instruction of EIC.

Supply and external installation of following sizes of Heavy Duty, Hot Dip Galvanised MS ERW Conduits for Electrical & Communication System with all the required accessories like round JBs, Solid Long Bends, Check Nuts, Nipples, Couplings, Reducers, Copper Clips, Copper Conductor, GI Wire etc. as per the detailed specification. (Refer Sec VI, Clause No.27), Size:- 25mm GI Flexible Hose

Supply and providing GI conduit downrod for installation of luminaries, fans etc as per the detailed specification. (Refer Sec VI, Clause No.16.5). Size:-20mm dia GI conduit

Supply and installation of the following sizes of copper wires in built in trench as per the detailed specification. (Refer Sec VI, Clause No.12.8), Size:-8SWG copper wire

Supply and fixing following Modular front cover plate on existing modular metal/plastic boxes etc. as required.

One module

Two Front Plate

3 Module

4 Module

Supply and Installation of following Wiring Accessories as per the detailed specification.

1 No 10A Switch on modular plate and termination of wires to the switches

1 No16A Switch on modular plate and termination of wires to the switches

1 No 6A 3 Pin shuttered type Socket on modular plate and termination of wires to the switches

1 No 6/16A 3 Pin combined shuttered type Socket on modular plate and termination of wires to the switches

Supply Installation testing and commissioning of the following MCB on Distribution Boards as per the detailed specification.

80Amps,Four pole MCB

125Amps Four Pole MCB

6-32 Amps Single Pole MCB

6-32 Amps DP MCB (DC)

Supply fixing testing and commissioning of the following RCCBs on Distribution Boards as per the detailed specification.

RCCB Double Pole 40A 30mA, TYPE AC

Supply and Installation of laminated Hylam sheet of 3mm thickness over the boxes and as per the detailed specification.

Supply & laying of 1 pair, 1.5 sq.mm Stranded copper conductor, flexible un-armoured cable, insulated Class-A, FRLS cable for FDAS

Supply & laying of 1 Pair, 1.5 sq mm Stranded copper conductor, flexible un-armoured cable, FRLS PVC sheath, insulated cores, twisted pair, Overall screened with Al-Mylar tape, voltage grade 1100V, applicable standard IS 1554 for PA system

Supply & Laying of CAT-6 Cable through embedded conduit / cassing-capping for Telephone system, CCTV System and LAN System

SEKAR CONSTRUCTIONS

M/s. Ashok constructions