6th Finance commsion 2022-23 and 23-24

Amount

Earth work excavation for foundation in all soils and sub soils and to full depth as may be directed except in rock requiring blasting but inclusive of shoring, strutting and baling out water wherver necessary as per SS 20 B etc., complete complying with standard specifications.

Collection, supply and filling with well gravel including cost and conveyance of all materials and stacking them at road side to departmental gauge for pre-measurement including all labour charges for filling etc., complete as per standard specification.

Plain Cement Concrete 1:4:8 (one cement,four sand and eight aggregate) mix using 40mm gauge hand broken hard granite stone jelly for foundation including dewatering if found necessary and laid in layers of not more than 15cm well rammed etc., complete complying with standard specifications.

Plain Cement Concrete 1:2:4 Mix (one part cement, two part sand and four part of aggrigate) using 20mm size ISS HBG metal machine crushed from approved quarry including cost and conveyance of all materials to site, loading and unloading charges and labour charges for mixing, laying and curing etc. complete. Complying with std. specifications.

Random rubble masonry in cement mortar 1: 5 (one cement five sand) in foundation and basement using best HBG Rough stone and Band stone with simultaneous flush pointing etc. complete complying with standard specifications and as per drawings and as directed by departmental Engineers using new rough stone & sufficient bond stones with simultaneous pointing including all cost & conveyance of materials.

Supplying and erecting Centering for sides and soffits including supports and strutting upto 3.29 m high for plane surfaces such as RCC slabs, Rectanular beams, Lintels and Stair case waist slabs conopy etc., in all floors with all cross bracings using mild steel sheets of size 90cm x 60cm and BG 10 stiffened with welded mild steel angles of size 25mm x 25mm x 3mm for boarding laid over country wood joists of size 10cm x 6.50cm spaced at about 90cm centre to centre and supported by Casuarian props of 10cm to 13cm dia spaced at 75cm centre to centre etc., complete and as directed by departmental Engineers. A. Footing and Plinth beam

B. Ground Floor Lintel beam

C. Ground Floor Roof slab

D. Columns

First floor A. First Floor Lintel beam

B.First Floor Roof beam and slab

C. Columns

Supplying, fabricating and placing in position mild steel/Ribbed for steel roads for all RCC works including cost of steel and binding wire also in all floors, complete complying with standard specifications.

Providing and laying in position Standardised Concrete Mix M-20 Grade in accordance with IS 456 - 2000 using 20mm and down graded hard broken granite stone jelly for all RCC items of works with minimum cement contenet of 325Kg/ cum and maximum water cement ratio of 0.55 including admixture (Plasticiser / super plasticiser) in recommended proportions as per IS 9103 to accelerate, related setting of concrete, improve workability without imparing strength and durability with about (5.0cum), 7730Kg of 20mm machine crushed stone jelly and with about (3.3 cum), 5156kg of 10 - 12mm machine crushed stone jelly and with about (4.79cum) 7670 kg of sand, but excluding cost of reinforcement grill and fabricating charges centering and shuttering but including laying, vibrating with mechanical vibrators, finishing, curing, etc and providing fixtures like fan clamps in the RCC floor / roof slabs wherever necessary without claiming extra cost etc., complete complying with standard specification and as directed by the departmental officers - The Coarse and Fine aggregates to be used should comply with the requiremnents of IS standards. (No separate payment will be made by the Department for the excess usage of materials) -Footing, Plinth beam, Tie beam/Lintel, Ground Floor Roof beam, salbs, Sloped roof beam and slabs A. Up to basement

Ground Flooor

First Flooor

Brick Work in Cement Mortor 1:5 Mix (one cement, five sand ) using new best country Bricks of size 8 ¾” x 4 ¼” x 2 ¾” from approved quarry including cost and conveyance of all materials to site. loading and unloading charges and labour charges for mixing, laying and curing etc. complete. complying with std. specifications. A.for foundation and basement

B. For Ground Floor

C. For First Floor

Supplying and fixing in position colour glazed INDIAN TYPE WATER CLOSET with 'P' or 'S' trap including cost and conveyance of water closet and labour for fixing including flooring with brick jelly concrete etc., complete

Special Ceiling Plastering and finishing all the RCC exposed surfaces such as RCC slabs, sunshades, conopies, staircase steps , etc., with cement mortar 1:3 (one cement three sand) mix to 10mm thick and including hacking the surfaces and providing necessary cement mortar nosing beading as per size, specification wherever necessary using the same mix as directed by the departmental officers etc., complete complying with standard specifications.

Plastering with cement mortar 1:5 (one cement three sand) mix to 12mm thick and including hacking the surfaces and providing necessary cement mortar nosing beading as per size, specification wherever necessary using the same mix as directed by the departmental officers etc., complete complying with standard specifications.

Plastering in cm 1:3, 12mm thick including cost and conveyence all materials to site and all labour charges and incidental charges etc.,completly complying with standard specifications.

Supplying and fixing over the floors best quality of scratch ceramic tiles of 30 c.m x 30c.m x 6mm size of approved colour laying with cement mortor 1:2 mix pointing the joints with colour pigments etc. Complete.

Paving the floor with vitirified tiles size 600 x 600 x 8mm of approved quality and colour of any size in all floors over 20mm thick cment mortar 1:3 (one cement and three sand) mix base above the existing bed concrete and pointing with same colour cement added with colouring pigments etc., complete complying with standard specification.

Paving the floor with pre-polished concrete anti-skid step tiles (Required shape and design) of 20mm thick of approved quality and colour laid in Cement Mortar 1:3 (One Cement and Three sand) 20mm thick and pointed with white cement mixed with colouring pigment at the rate of 0.40 Kg. / sq.m., curing, etc., complete complying with standard specification and as directed by the departmental officers. (The make and brand of the tiles should be got approved by Executive Engineer before use on works)

Dadooing sides of walls with Glazed tils of size 0.30m x 0.20m x 0.006m including cost and conveyance and all labour and materials complete complying with standard specifications and drawings and as directed by the departmental Engineers.

Supplying and fixing RCC Pre cast slab in RCC 1:2:4 mix including cost of reinforcement grill but including moduling, finishing watering curing and fixing in position etc., Complete as per std., Specifications.

Manufacturing, supplying and fixing of STEEL DOORS with following specification. MS Angle of size 35 x 35 x 5 mm at 2.60 Kg/m used for outer frame and MS Angle of size 25 x 25 x 5 mm at 1.80 Kg/m for the shutter frame. Stiffeners with 25 x 5 mm at 1.20 Kg/m MS Flat is provided as the lock rail of the door and welded intact on both ends to the shutter frame. 18 GCR Sheets of best qulaity is laid as panel in the shutter frames. 18 x 5 mm at 0.70 Kg/m MS Flat is welded over the 25 x 5 mm at 1.20 Kg/m MS Flat on the rear side of the door, sand witching teh CR Sheet for rigidity. Additional stiffeners with 18 x 5 mm at 0.7 Kg/m MS Flats are provided diagonally on the rear side of the shutter. A tie bar is provided at the bottom of the outer frame to prevent twisting of the frame during transportation and fixing. All members are given one coat of red oxide primer as directed by the departmental officers. The rate includes cost of all materials, labour charges,

Manufacturing, supplying and fixing in position of STEEL SHEETED WINDOWS with the following specifications. Outer frames of Windows made of 'Z' Section F7D of size 33 x 25 x 3 mm at 1.419 Kg/m and mullion 'O' Section (F4B) of size 46 x 25 x 3 mm at 2.28 Kg/m and shutter section of made of F7D of 33 x 25 x 3 mm at 1.419 Kg/m as specified in IS 7452/1990. Each openable shutter should not exceed a width of 600 mm to enable separate operations and easy maintenance. The panel of the shutter to be covered with 18 Gauge cold rolled sheet of superior quality and welded intact withshutter frames. Four Nos. of hold fasts of 10 mm length spllced at the ends are welded to the outer frame of the window by using MS Flat of 18 x 5 mm at 0.70 Kg/m, welded to the shutter at two place equivalent from each other from top and bottom of the shutter. The cost includes cost of all materials, labour charges and other incidental charges, etc., complete.

Supplying and fixing in position of M.S grills using for windows and ventilators in position including labour charges for fixing furniture fittings for windows & ventilators with standard drawings , etc., complete complying with standard specifications.

Painting iron works for doors, windows and ventilators, iron bars, weldmesh, wiremesh screen, steel bars , flats and other similar works etc., with Two coats of approved first quality of synthetic enamel paint over the existing red oxide primer in all floors it inclusive of cost of materials and labour, brushes and scaffolding etc., complete complying with standard specifications.

White washing two coats with best quality of slacked shell lime including cost and conveyence all charges etc.,completly complying with standard specifications.

Emulsion paint two coats using best approved colour and quality cement paint in all floors including cost of lime and other materials, brushes, scafolding charges etc., complete complying with standard specifications and as directed by departmental officers.

Weathering course concrete with broken brick jelly of 20 mm gauge in pure slacked lime ( no sand to be added) over roof slab the proportion of brick jelly to lime being 32 to 12.5 by volume and laid over In a single layer and consolidated require designed and finished thickness by beating the concrete with wooden beaters of approved pattern , keeping the surface constantly welded springing lime jiggery water asper standard specification and as directed by the departmental officers.

Finishing the top of roof with one course of machine pressed tiles of size 20 x 20 x 2 cm laid in cement mortar ( One of cement and three of sand ) mixing with water proofing compound conferment ISS at 2% weight of cement used and pointed with same waterproofing compound mixed with red oxide etc., complete with standard specification

Providing Galvalume sheet roofing using 0.47mm thick including all cost of materials at the site and necessary bolt and nots including all labour charges etc. complete as per standard specification.

Supplying and fixing of 16mm thick bison shutter including cost of suitable "T" hinges, bolt nuts, handle and cost of teak wood lipping for alround the bison shutters. Including cost and conveyance and labour charges for wrought and put up etc., complete.

Supply and fixing in position of RCC Jolly 50mmtk including cost and conveyance of all material to site and all other labour charges for fixing etc., Complete.

Supply of thousand ltr. capacity PVC water tank including cost and conveyance Complete complying with standard specifications and as directed by the departmental Engineers.

Rubberised Interlocking Paver Block M40 grade providing and laying of 83mm thick heigh strength type confiriming IS 15658 - 2006 of Rubberised Interlocking Paver Block in required size of mininmum compressive strength of 40N/mm2 in uniform shape of approved make to be laid in flumying bore pattern with approved nin - sticking surface in the top and the rate including levelling the base cushion 150mm thick laying out the pavement cut the pieus to fit edge, vibrating pavers, sweeping transporting leading unloading as per standard specification.

Providing and fixing P.V.C. Rainwater Downfall pipes of 110mm diameter with necessary shoes, bends and other specials, clamps, screws, nails, teakwood plugs etc., complete including cost of all materials. The rate is to include cost of removable cast iron Gratings of appropriate size. The size of teakwood plugs to be used is 150mm * 25mm in front and 200mm * 75mm in rear and all other sides with a depth of 100mm. The pipe is to be fixed by means of "U" clamps at the centre of the pipe screwed to the plugs. The special type of 'U' clamps at the centre of the pipe to be fixed in addition to these for more than three metres pipe length, complete complying with standard specification.

Supplying and fixing of 110mm dia PVC (4kg/cm2) pipes including cost and conveyence of all materials and all other labour charges and incidental charges etc., completly complying with standard specifications.

Supply and run of 2 x 1.5 Sq.mm (22/.3) PVC Insulated SC unsheathed CU. Conductor of 1100 Grade in 25mm Dia GI Pipe (Glass “B”) suitable Bent of both ends with necessary angle iron upright and end supports for Mains (SD 69).

Supply and run of 2 of 1.5 sq.mm (22/0.3) PVC insulated SC unsheathed Cu.Conductor of 1100V grade on 7/20 GI bearer wire for service connection mains (SD.64)

Wiring with 2 x 1.5 sq.mm. (22 / 0.3) PVC insulated SC unsheathed copper conductor of 1100V grade in suitable PVC rigid pipe concealed in wall and ceiling with PVC accessoires in flush with wall with 3mm thick hylum sheet cover with TW switch box and 5A FT switch and making good of the concealed portion with suitable colour for PVC concealed light / fan Point (for electronic regulator) (5 points per coil) (SD 25)

Supply and fixing of WT bulk head fitting with guard suitable for 11W CFL lamp with CFL (SD 83)

Supply and fixing of single box type 4’40W flu. Fitting complete with tube copper choke and condenser with conduit pipe suspension from the ceiling with PVC unsheathed leads from terminal to the fittings (SD. 88).

Supply and fixing of 1200mm (48") sweep AC ceiling fan complete with stepped electronic 300W regulator with 1 metre down rod with fan clamp with side plates and cross arm of size 450mm (18")s (SD. 88).(SD 106)

Supplying and fixing in position best Indian make white glazed earthenware WASH HAND BASIN of 560x406mm with a a pair of C.I. Brackets, 15mm dia C.P. Pillar tap, 32mm G.I. Waster water pipe, 32mm dia C.P. Brass waster coupling, plug with chain, 15mm dia PVC connection, 15mm G.M. wheel valve with ISI mark and necessary G.I. union and G.I. Elbow, including fixing wash hand basin in position with white lead, clamps, teakwood plugs, screws, rubber washer etc., complete without any leakage complying with standard specifications.

Supplying and fixing in position best Bevelled Edge MIRROR of 6mm thick of size 50cm x 40cm fibre glass shelf type with necessary plywood backing and rubber button, chromium plated screws, teakwood plugs, etc., complete complying with standard specification and as directed by the departmental officers.

Supplying and fixing in position best Indian make Aluminium anodised TOWEL RAIL of approved quality and size 60cm long and 20mm dia with brackets of same material including fixing with necessary teak wood plugs C.P. Screws etc., complete as directed by the departmental officers.