Loading
Loading…
Loading…
Tender Value
₹70.7 L
EMD Value
₹1.4 L
Closing Date
22 Jul 2025, 3:00 pmClosed
No
No
Single Packet System
Normal Tender
No
Not Applicable
Lowest to Highest
60 days
Expenditure
Capital (Works)
Above/Below/Par
TELECOM
15 conditions · 2 needing a document upload
The tenderer must have minimum average annual contractual turnover of V/N or 'V' whichever is less; where V= Advertised value of the tender in crores of Rupees N= Number of years prescribed for completion of work for which bids have been invited. The average annual contractual turnover shall be calculated as an average of "total contractual payments" in the previous three financial years, as per the audited balance sheet. However, in case balance sheet of the previous year is yet to be prepared/ audited, the audited balance sheet of the fourth previous year shall be considered for calculating average annual contractual turnover. The tenderers shall submit requisite information as per Annexure-VIIB of Northern Railway Standard Tender Document- 2022, along with copies of Audited Balance Sheets duly certified by the Chartered Accountant/ Certificate from Chartered Accountant duly supported by Audited Balance Sheet.
(a) The Tenderer must have successfully completed or substantially completed any one of the following categories of work(s) during last 07 (seven) years, ending last day of month previous to the one in which tender is invited: (i) Three similar works each costing not less than the amount equal to 30% of advertised value of the tender, or (ii) Two similar works each costing not less than the amount equal to 40% of advertised value of the tender, or (iii) One similar work costing not less than the amount equal to 60% of advertised value of the tender. (b) (i) In case of tender for composite works (e.g. works involving more than one distinct component, such as Civil Engineering works, S&T works, Electrical works, OHE works etc. and in the case of major bridges- substructure, superstructure etc.), tenderer must have successfully completed or substantially completed any one of the following categories of work(s) during last 07 (seven) years, ending last day of month previous to the one in which tender is invited: (i) Three similar works each costing not less than the amount equal to 30% of advertised value of each component of tender, or (ii) Two similar works each costing not less than the amount equal to 40% of advertised value of each component of tender, or (iii) One similar work each costing not less than the amount equal to 60% of advertised value of each component of tender. Note: Work experience certificate from private individual shall not be considered. However, in addition to work experience certificate issued by any Govt. Organization, work experience certificate issue by Public listed company having average annual turnover of Rs. 500 crore and above in last 3 financial years excluding the current financial year, listed on National Stock Exchange or Bombay Stock Exchange, incorporated /registered at least 5 years prior to the date of closing of tender, shall also be considered provided the work experience certificate has been issued by a person authorized by the Public listed company to issue such certificates. In case tenderer submits work experience certificate issued by public listed company, the tenderer shall also submit along with work experience certificate, the relevant copy of work order, bill of quantities, bill wise details of payment received duly certified by Chartered Accountant, TDS certificates for all payments received and copy of final/last bill paid by company in support of above work experience certificate.
Substantially Completed Work means an ongoing work in which payment equal to or more than 90% of the present contract value (excluding the payment made for adjustment of Price variation (PVC), if any) has been made to the contractor in that ongoing contract and no proceedings of termination of contract on Contractor's default has been initiated. The credential certificate in this regard should have been issued not prior to 60 days of date of invitation of present tender.
Defination of Similar Work :- I) Work of supply , installation, testing and commissioning of PDH/SDH, ADM/PD Mux and its associated equipment's or ii) AMC of PDH/SDH, ADMs, PD Mux/faulty Card of Mux repair work and associated equipment's o r iii)Work of excavation of Trench and underground cable laying jointing of copper cable or OFC cable o r iv) Trenching, laying, splicing and testing of OFC Cables and part supply, Testing and Commissioning of SDH equipment's or v) Trenching, laying, jointing and testing of 6 quad/PIJF cables including, Erection and testing of emergency socket and part supply , testing and commissioning of repeater Equipment's. or vi)Trenching, laying splicing/jointing and testing of OFC /6-quad cables, Erection & testing of emergency socket and part supply, testing and commission of SDH/repeater equipment.
32 conditions · 15 needing a document upload
1. Tender fee (if asked) need to be deposited online on www.ireps.gov.in. 2. EMD need to be deposited online on www.ireps.gov.in. 3. For the tenders costing above 50 Lacs: Details of "total contractual payments" in the previous three financial years. 4. For the tender costing above 50 Lacs: Details of technical credentials have successfully completed or substantially completed similar nature work as mentioned in tender condition. Completion certificate issued by competent authority should mandatorily mention Name of work, name of agency, Contract agreement number, date of completion/date of completion of substantially completed work, Completed Cost/substantially completed cost of work, Nature of firm (Partnership/Proprietorship etc.) and details of its constituents, if any, PAN/GSTIN etc. so that evaluation may be done accordingly. 5. If Tenderer is sole proprietor: Notarized copy of Affidavit on Stamp paper of appropriate value declaring that his/her concern is a Proprietary concern. 6. If Tenderer is Partnership firm: Self attested copy of (i) Registered/Notarized partnership deed (ii) Original/Notarized power of attorney. 7. If Tenderer is JV/Limited Company: Copy of Memorandum and Articles of Association of the company. Power of Attorney (duly registered/notarized as per prevailing law) by the company authorizing the person to do/act on behalf of the company. 8. If Tenderer is Company: Copies of MOA (Memorandum of Association) & AOA (Articles of Association) of the company. Power of attorney duly registered/notarized by the company in favour of the individual signing the tender on behalf of the company. Resolution of Board of directors in regards of approving Power of attorney issued. 9. If Tenderer is Society: Attested copy of the certificate of registration. Deed of formation. Power of attorney in favor of the tender signatory.10. Copy of PAN number and TIN number.
Please enter the percentage of local content in the material being offered. Please enter 0 for fully imported items, and 100 for fully indigenous items. The definition and calculation of local content shall be in accordance with the Make in India policy as incorporated in the tender conditions.
Please submit the copy of the registration certificate of firm, PAN, GSTIN etc.
Telecom Work in c/w Renovation of Control Office chambers of DRM office Firozpur along with misc. work-related to control.
433-Sig-T-10-25-26
433-Sig-T-10-25-26
Open
Works - General
4 Months
Firozpur, Punjab
₹0
₹1.4 L
22 Jul 2025
30 Jun 2025
113 items across 3 schedules
| # | Description | Unit | Qty | Rate | Amount |
|---|---|---|---|---|---|
| — | — | — | 35,90,238.78 | ||
| — | 2000.00 | — | — | ||
| Supply of Single mode 6 Fiber Armoured Optic Fibre Cable. It shall Comply to TEC Spec.No.G/OFC-02/03.September2003 (TEC Standard Number-TEC85010:2003) of make Finolex or Legrand or paramount. Inspection by Consignee. OEM supporting certificate shall be provided that the material has been manufactured as per specification attached. | — | — | — | 61,340 | |
| — | 2135.00 | — | — | ||
| Supply of CAT-6 (STP)cable as per RDSOspecificationRDSO/SPN/TC/65/2016Rev. 3.0 or latest of make- D link or Legrand or Molex. OEM supporting certificate shall be provided that the material has been manufactured as per specification attached.Inspection by Consignee. | — | — | — | 55,574.05 | |
| — | 320.00 | — | — | ||
| Supply of Power Cable 3 Core 1.5 Sqmm. Multi Strand Copper Conductor, PVC Insulated, as per IS:694: 1990 with Latest amendments & Versions. Inspection by Consignee. | — | — | — | 17,420.8 | |
| — | 4455.00 | — | — | ||
| Supply of 25mm. dia PVC Conduit Pipe (MMS) ISI marked as per: IS 9537 part-3 with all required accessories (metal clamping, Bends etc. shall be use). Inspection by Consignee. | — | — | — | 1,34,674.65 | |
| — | 15.00 | — | — | ||
| Supply of 1 KVA UPS (APC Back- UPS Pro BR1000G-IN) or equivalent specification of reputed make. Inspection by Consignee. | — | — | — | 1,00,979.7 | |
| — | 4.00 | — | — | ||
| Supply of Lighting and surge arrestors of Class B&C suitable for single phase power supply in T&T(Earth to earth) network as per amendment no. 5 of RDSO/SPN/TC/165/2004 or latest and as recommended by RDSO vide letter no. STE/E/IPS/GENL dated 27.01.2006 procured from RDSO approved manufacturers only. OEM supporting certificate shall be provided that the material has been manufactured as per specification attached. Inspection By consignee | — | — | — | 96,392.24 | |
| — | 3.00 | — | — | ||
| Supply of SDH Add/Drop MUX (STM1) for main stream at stations in cable hut/OFC equipment rooms per TEC GR No.TEC/GR/TX/SDH-004/04/Jan-11 or latest with L1.1 Optical Aggregate Interface and as per technical requirements for OFC system, equipped with 21 E1s (including engineering order wire), expandable up to 63 E1s capacity simply by addition of E1 cards, fully wired, having cross connect granularity at VC-12, VC-3 & VC-4 levels, power unit, sub-racks, 4 port 10/100 Mbps Base-T Ethernet, installation materials with all other accessories and technical manuals etc. STM1 to be inspected and supplied together with additional cards (additional cards covered separately). Material should be procured from RDSO/TEC approved vendor or OEM supporting certificate shall be provided that the material has been manufactured as per RDSO/TEC specification attached. Inspection by RDSO. | — | — | — | 5,07,378.33 | |
| — | 2.00 | — | — | ||
| Supply of additional 21 E-1 card to be inspected and supplied together with STM-1. | — | — | — | 38,078.1 | |
| — | 50.00 | — | — | ||
| Supply of Optical Fibre Jumper (Patch cord) (10 Meter long) with LC & LC (or suitable connector) at both ends as per RDSO/SPN/TC/69/2007, Rev. 0, or latest. This connector should be compatible with FMS/STM/Mux. Material should be procured from RDSO approved vendor or OEM supporting certificate shall be provided that the material has been manufactured as per RDSO specification attached . Inspection by consignee | — | — | — | 29,488.5 | |
| — | 45.00 | — | — | ||
| Supply of optical fibre jumper cable (patch cord) ( 10 metre long) with FC-PC or SC/APC or suitable connector ) at both ends as per RDSO/SPN/TC/69/2007, Rev 0, or latest.The connector should be compatible with STM. Inspection by consignee. | — | — | — | 20,307.6 | |
| — | 10.00 | — | — | ||
| Supply of U link Panel complete with 32 Nos of U links. Inspection by Consignee. | — | — | — | 18,342.9 | |
| — | 3.00 | — | — | ||
| Supply of SMPS based battery charger for telecom use of 230VAC(90 VAC to 300 VAC)/48V DC, 25Amp capacity. This shall consist of modules of 25 Amp modules in1+1 configuration or 12.5A modules in 2+1 configuration with automatic switching between the modules as per RDSO specification no. RDSO/SPN/TC/23/99 (ver. 4),Amendment-1 or latest. This includes 10 Sq. MM copper wire in Red and Black color for interconnecting charger to VRLA battery & equipment. Material should be procured from RDSO/TEC approved vendor or OEM supporting certificate shall be provided that the material has been manufactured as per RDSO/TEC specification attached. Inspection by Consignee. | — | — | — | 2,71,489.89 | |
| — | 3.00 | — | — | ||
| Supply, Transportation and connection of VRLA secondary Battery 48V/200AH with all accessories with two no. manual of instructions with each set as per RDSO Specification no. S-93- 96,Amendment 1, or latest. Material should be procured from RDSO/TEC approved vendor or OEM supporting certificate shall be provided that the material has been manufactured as per RDSO/TEC specification attached. Inspection by Consignee. | — | — | — | 2,83,477.47 | |
| — | 3.00 | — | — | ||
| Supply of 2MB programmable primary digital drop insert multiplexer with conference facility as per technical specification No.IRS/TC/68/2012, Rev. 0, or latest without maintenance portable terminal, fully wired for 30 channels with redundant power supply unit, remote control supervisory facility and all other accessories, installation material,technical manuals etc. The MUX shall be supplied with full capacity of cards i.e. 1 card for 64 kbps(G.703), 1 card for 2W Hotlinecircuits, 2 card for 2W Subscriber interface circuits, 2 card for 2W exchange loop, 1 card for V.24 low speed data interface for SCADA, E1 branching Interface and rest cards for 4W E&M VF circuits Each card should preferably be of minimum 4 circuits except SCADA card of minimum 2 channels. This includes supply of Male/Female Jacks and accessories as required as per the Design of MUX. PD MUX to be inspected and supplied together with additional cards (additional cards covered separately). Material should be procured from RDSO/TEC approved vendor or OEM supporting certificate shall be provided that the material has been manufactured as per RDSO/TEC specification attached. Inspection by Consignee. | — | — | — | 4,51,729.8 | |
| — | 8.00 | — | — | ||
| Supply and testing of additional 4W E&M VF Interface cards (same as supplied with above item of PD MUX), to be inspected and supplied together with PD MUX. | — | — | — | 81,260.08 | |
| — | 8.00 | — | — | ||
| Supply and testing of additional Subscriber loop interface cards (same as supplied with above item of PDMUX), to be inspected and supplied together with PD MUX. | — | — | — | 82,555.84 | |
| — | 10.00 | — | — | ||
| Supply of LAN extender as per RDSO spec no. RDSO/SPN/TC/82/2013 rev 1.0 or latest. OEM supporting certificate shall be provided that the material has been manufactured as per Specification attached. Inspection by Consignee. | — | — | — | 1,17,480 | |
| — | 270.00 | — | — | ||
| Supply of RJ-45Connector with cap.Make- D-Link or better.Inspection by consignee. | — | — | — | 2,457 | |
| — | 1.00 | — | — | ||
| Supply of Router 4 WAN/G-703 Interface and 2 LAN interface as per RDSO specification no. RDSO/SPN/TC/84/2008 Rev. 0 or latest. Material should be procured from RDSO/TEC approved vendor or OEM supporting certificate shall be provided that the material has been manufactured as per RDSO/TEC specification attached. Inspection by Consignee. | — | — | — | 79,178 | |
| — | 20.00 | — | — | ||
| Supply of Single mode 1G SFP module compatible to Layer 2 switch. INSPECTION: CONSIGNEE | — | — | — | 69,934.4 | |
| — | 10.00 | — | — | ||
| Supply & Installation of OFC Joint Enclosure for 6 core OFC. MAKE- Molex or Legrand or D-Link. Inspection by Consignee. | — | — | — | 2,900 | |
| — | 10.00 | — | — | ||
| Supply of E1 to Ethernet Converter, should be able to convert data stream from G 703 interface (2MBPS) to Ethernet & vice versa compatible to IEEE 802.3 operating voltage 230v AC50Hz. through DC 5 Volt adopter Make:- Cygnus/ ANDA or Similar. Inspection by Consignee. | — | — | — | 1,10,868.9 | |
| — | 40.00 | — | — | ||
| Supply of cat-6 UTP patch cord of 8 inch length. Inspection by Consignee. | — | — | — | 4,109.6 | |
| — | 70.00 | — | — | ||
| Supply of Cat 6 UTP patch cord of 2 mtrs length. Inspection by Consignee. | — | — | — | 15,345.4 | |
| — | 10.00 | — | — | ||
| Supply of 2.048 mbps SHDSL modem as per RDSO spec no.RDSO/SPN/TC/80/2008rev 0.0 with amendment1 or latest. Material should be procured from RDSO approved vendor or OEM supporting certificate shall be provided that the material has been manufactured as per RDSO specification. Inspection by Consignee | — | — | — | 1,60,427.2 | |
| — | 2.00 | — | — | ||
| Supply of Portable digital auto range multi-meter clamp type Philips, Motwani, Fluke or Rishabh make or similar capable to measure from (0.1 mv/0.01mA)AC/DC up to 10 Amp (AC/DC),1000V (AC/DC) and 0.1 ohms-40Mohms suitable for measurement of Freq., capacitance, temperature complete with accessories, Manual, leads, battery and holster etc. Inspection by Consignee. | — | — | — | 12,088.42 | |
| — | 1.00 | — | — | ||
| Supply of Optical power meter (Type-B) as per TEC Specification No. TEC/GR/TX/OPM- 001/04. NOV.2013 with latest amendments. Material should be procured from TEC approved vendor or OEM supporting certificate shall be provided that the material has been manufactured as per TEC specification attached. Inspection by Consignee | — | — | — | 29,928.16 | |
| — | 2.00 | — | — | ||
| Supply of Transmission Measuring Set (TMS Kit ) Complete with Tone generator and dB meter as RDSO Specification IRS:TC-43/87 or latest. Material should be procured from RDSO approved vendor or OEM supporting certificate shall be provided that the material has been manufactured as per RDSO specification. Inspection by Consignee | — | — | — | 43,821.34 | |
| — | 6.00 | — | — | ||
| Supply of single mode media convertor as per RDSO specification no. RDSO/SPN/TC/103/2013 Rev. 0.0 Amendment 1 or latest. OEM supporting certificate shall be provided that the material has been manufactured as per specification attached. Inspection by Consignee. | — | — | — | 43,560.3 | |
| — | 3.00 | — | — | ||
| Supply of HP LASER JET P1108 Plus SINGLE FUNCTION MONOCHROME LASER PRINTER Make: HP LASER JET P1108 plus or better. Inspection by Consignee | — | — | — | 42,364.95 | |
| — | 1.00 | — | — | ||
| Supply of Intel Core i3 All in One PC with 23.8 Inch Display/ Windows 11 with 512GB SSD, 8GB RAM or better, make hp or similar for fault finding in control office. Inspection by Consignee | — | — | — | 54,756 | |
| — | 10.00 | — | — | ||
| Supply of 12V 65 AH Sealed Maintenance free ( SMF ) with on-site warranty of minimum 2 year. Make : Amararaja Batteries, Exide or HBL Power System, Okaya or similar. Inspection by Consignee. | — | — | — | 52,160 | |
| — | 2.00 | — | — | ||
| Supply of E1 tester/Analyzer make XGXC model no.XG2330. Inspection by Consignee. | — | — | — | 3,30,400 | |
| — | 1.00 | — | — | ||
| Supply of 24 port layer 3 switch as per RDSO specification no. RDSO/SPN/TC/65/2016 Rev. 4.0 or latest. Material should be procured from RDSO approved vendor or OEM supporting certificate should be provided that the material has been manufactured as per RDSO specification attached. Inspection by Consignee. | — | — | — | 1,67,969.16 |
Tap a document below to read it instantly. You can also download everything as a ZIP if you prefer.
details.html
HTML
nit.pdf
NIT
Download all tender documents and submit your bid
Disclaimer: TenderKart has made every reasonable effort to ensure that the information on this page is accurate and authentic, however it cannot be held liable for any third-party claims or losses or any damages. TenderKart makes no warranty, expressed or implied, as to the results obtained from the use of this information. If you notice any error or omission, please let us know at .