Construction of old age recreation and women welfare centre at Village Jharera, Delhi Cantt

Amount

Demolition of cement concrete of any description and in any position not otherwise specifically provided for

Dismantling of brick work or stone/boulder masonery, built in any cement mortar including all quoins, arches, pillars, etc. but excluding ashlar facing, dressed stone work and precast concrete articles.

Excavation over areas, not exceeding 1.5 mtr deep for foundation etc. or for shaft, bells, cesspits, manholes, pier holes and getting out of any type of soil.

Excavation in trenches, not exceeding 1.5 mt wide and not exceeding 1.5 mt in depth; for foundation etc or for shafts, wells, cesspits, manholes, pier holes, etc. not exceeding 10 sqmt on plan and not exceeding 1.5 mt in depth and getting out in any soil

Returning, filling in earth, including spreading, leveling, watering and well ramming in layers not exceeding 25 cm thick.

Removal of demolished / excavated material to any approved dumping site out side Cantonment limit, under contractor's own arrangements as per direction of Engineer-in-Charge.

Providing and laying cement concrete in foundations, filling and mass-concrete and under floors , drain beds and like, type D-2, 1 : 4 : 8 mix (1 cement :4 coarse sand : 8, 40 mm graded stone aggregate).

Providing and laying cement concrete in roof kerbs or mud stops, rounded or chamfered on edge, volumetric mix 1 : 1.5 :3 mix (1 cement : 1.5 coarse sand : 3. 20 mm graded stone aggregate).

Providing and laying cement concrete in lintels up to 1.5 mt clear span, cills, steps, seismic and other similar bands , plinth courses, string courses, lacing courses parapets and railings up to 60 cm in height, copings, kneelers, apex stone, bed plates, kerbs, water troughs and the like including weathering, slightly rounded or Chamfered angle and throating as directed by Engineer-in-Charge with B-1 type 1 : 1.5 : 3 mix (1 cement : 1.5 coarse sand : 3, 20 mm graded stones aggregate). Including hold fast concrete

Providing and laying reinforced cement concrete in foundations including rafts, footings, foundation, plinth beams, bases of column etc using M-25, design mix concrete.

Providing & laying reinforced cement concrete in slabs; supported on walls, beams and columns; in floors, roofs, landings balconies, canopies, deck slabs and in shelves and the like, including stairways including steps, string pieces, carriages, etc. with using M-25, Design mix concrete.

Providing & laying reinforced cement concrete in chajjas using M-25, Design mix concrete.

Providing & laying reinforced cement concrete in beams, cantilevers, brassummers, lintels over 1.5 mt span with using M-25, Design mix concrete.

Providing and laying reinforced cement concrete in columns, pillars, piers, posts and struts with using M-25, Design mix concrete

Providing & laying reinforced cement concrete in fins, fascias, louvers, parapets, and railings exceeding 60 cm in height, newels, balustrade, and the like with using M-25, Design mix concrete.

M&L autoclaved areated cement blocks masonary with 100mm thick AAC blocks of minimum size 600x200x200 mm in superstructure above plinth level in cement mortar 1:4 (1 cement : 4 coarse sand) including providing and placing in position 2 nos 8 mm dia M.S. bars at every third course of masonry work (MS bars shall be paid separately)

Material and labour, Brick work with "A" class bricks, class designation 100, straight or curved on plan exceeding 6 mt mean radius, built in cement mortar 1 : 4 (1 cement : 4 coarse sand)

Brick work in half brick wall, with cement mortar 1:4 (1 cement :4 coarse sand) with sub class 'A' bricks.

M& L ,Form work to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200 mm thick (horizontal or sloping) for fair finished surfaces.

M& L , Form work to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves, ramps, including supports, overhangs, etc, also splays between floors and beams, etc. for fair finished surface.

M&L ,Form work to sides of pillars, posts, struts, piers, columns and stanchions for fair finished surfaces of concrete rectangular, square or polygonal shape

M&L form work to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soflits of foundation and plinth beams etc for fair finished surface.

M &L ,Form work to edges of concrete flats, treads, break in floors, window cills, concrete railings, openings in concrete walls, floor and roofs not exceeding 20 cm wide and sides of RCC/PCC bands in walls, horizontal or sloping and similar work exc. 10 cm but not exc. 20 cm wide for fair finished surfaces.

Supplying & Fixing, Pressed steel frames for doors with one or more rebate including necessary fixing lugs, hinges, lock strike plate, etc. complete as specified, supplied and fixed, size of frame 105X60mm, Profile ‘A’

Supplying & Fixing, Pressed steel frames for doors with one or more rebate including necessary fixing lugs, hinges, lock strike plate, etc. complete as specified, supplied and fixed, size of frame 165X60mm, Profile ‘C’ double rebate

Filling hollow of frame with plain cement concrete 1:3:6, type C-1 to size of frame 105X60mm.

Supplied and fixed 40 mm thick factory made flush shutters, solid core construction, with block board core and plywood face panels, with decorative face veneers on both sides. Approved makes : National Plywood Industries, Centuary Plyboard (India) Pvt. Ltd., Sarda Plywood Industries Limited, Kitply Industries Limited, Duroply Industries Limited, Greenply Industries Limited.

Supplying and fixing 150 mm long stainless steel, anodized, barrel tower bolts of approved design and make.

Supplying and fixing 200mm long stainless steel designer barral tower bolt.

Providing and fixing 300mm stainless steel altrops (sliding door bolt) with hasp and staple (bolt type) fixed in position complete all as directed by Engineer-in-Charge.

Supplying and fixing 100 mm butt hinges, medium weight, cold rolled mild steel.

Supplied and fixed stainless steel handles designer finished, size 150mm.

Supplying and fixing door stopper, stainless steel body min 100mm long.

Supplying and fixing door closer of aluminium body hydraulically regulated, designation No. 3, universal type, suitable for door shutters of any weight between 61 kg to 80 kg and fixed.

Supplying and fixing framed work such as grills, gratings, railings, etc., with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; frame work of water tanks and similar work conforming to Fe-410-0 or Fe 310-0.

M&L, Mild steel pipes/tube 50 mm dia medium grade, fixed in position as directed by Engineer-in-charge for M.S. Railing and like.

Mild steel TMT bars 8 mm dia and over, cut to length, bent to shape required including cranking, bending spirally for hooping for columns, hooking ends and binding with mild steel wire (annealed) not less than 0.9 mm dia or securing with clips including steel for spacers, binders, striupps etc complete all as directed by the Engineering in charge.

Supplying and fixing Joist, channel, angle, or tee sections,fixed independently, without connecting plates, etc. (cut to ordinary lengths i.e. within 20 mm of the length indicated using Fe-410W(Gde-E-250) quality– ‘A’

Supplying and fixing framed work as in doors or gates of angle or other section with gusset plate rails, braces etc, complete, drilled for fixing of steel sheeting or other covering. Doors, etc, to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails and guides) and hanging also fastening and fixing complete using 410W (Gde-E-250) quality ‘A’

Supplying and fixing Mild steel, plain, black sheet 1.60 mm thick in wall cladding, steel gates and similar work, cut to size, holes punched; including round headed screws, clout nails or rivets and fixed to wood or steel framing with plain 40 mm lap joints with riveted or welded seams, including bending or turning up, mitred angles, etc, as required.

Providing and fixing powder coated Aluminium ( minimum thickness of powder coating 50 micron ) work for doors, windows, ventilators and partitions with extruded built up standard tubular sections / appropriate Z sections and other sections of approved make confomring to IS : 733 and IS : 1285 fixing with dash fasterners of required dia and size, including hinges necessary filling up the gaps at juncitons, i.e. at top. bottom and sides with required EPDM rubber/neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight , mitred and jointed mechanically whereever required including cleat angle, Aluminium snap beading for glazing /paneling CP brass/stainless steel screws, all complete as per architectural drawings and the direcitons of Engineer-in-charge. ( Glazing , paneling and dash fasterners to be paid for separately)

for fixed portions

For Shutters of doors , window and ventilators including providing and fixing hinges/pivots and making provision for fixing of fittings whereever required including the cost of EPDM rubber/neoprene gasket required , powder coated (fittings shall be paid for separately).

Providing and fixing anodised aluminium grill (anodised transparent or dyed to required shade according to IS: 1868 with minimum anodised coating of grade AC 15) of approved design / pattern, with approved standard setion and fixed to the existing window / ventilator frame with C.P. brass / stainless steel screws @ 200 mm centre to centre, including cutting the grill to proper opening size for fixing and operation of handles and fixing approved anodised aluminium standard section around the opening, all complete as per requirement and direction of Engineer-in-Charge. (only weight of grill to be measured for payment).

Supplying and fixing of 160 mm internal dia unplasticised-rigid PVC rain water pipes conforming to IS 13592 Type ‘A’ including joining with sockets using seal ring conforming to IS 5382 leaving 10 mm gap for thermal expansion.

P&F, unplasticised PVC moulded fittings / accessories for unplasticised rigid PVC rain water pipe conforming to IS 13592 Type ‘A’ including jointing with seal ring conforming to IS 5382 leaving 10 mm gap for thermal expansion

160 mm bend 87.5 degree.

160 mm coupler

M&L, sand filling under floors or in foundations including watering and consolidated complete all as directed by Engineer-in-Charge

M&L, 100mm thick cement concrete type D-2, 1 : 4 : 8 (1 cement : 4 coarse sand : 8 - 40 mm graded stone aggregate) in sub base of flooring.

M&L, Kota stone (Size 22"x 22" or above) polished slab Machine cut(of any shade / colour/texture) 18 mm thick machine cut, in flooring, stair case, counters, skirting / dado/treads/ risers of steps & like laid over screed bed of minimum 20 mm thick in cement mortar 1:4 (1 grey cement : 4 coarse sand) and jointed with grey cement slurry and pointed with white cement with admixture of pigment to match the shade of kota stone. (No extra payment for making borders with other stone shall be payable)

Granite finish polishing , mirror finish, for Kota stone complete as directed by Engineer-in-Charge.

Material & labour white marble stone 18 mm thick machine cut (in narrow width), in flooring, stair case, counters, skirting / dado/treads/ risers of steps & like laid over screed bed of minimum 20 mm thick in cement mortar 1:4 (1 grey cement : 4 coarse sand) and jointed with grey cement slurry and pointed with white cement with admixture of pigment to match the shade of marble stone.

Providing and fixing first quality ceramic designer digital wall tiles, interior grade of approved make, colour pattern, texture as approved by the Engineer Incharge of any size upto 0.30 sqmt with minimum thickness of 8mm laid on 15mm thick 1:4 cement mortar (1 Cement : 4 coarse sand) and jointing with grey cement slurry @ 3.3 kg per sqmt, including pointing in white cement mixed with pigment to match the shade complete.

Providing and laying M-25 Cement concrete in floors and like

Making half round nosing in marble stone, granite stone, kota stone as per direction of Engineer-in-charge.

M&L, 75 mm thick cement concrete type A-1, 1 : 1.5 : 3 (1 cement : 1.5 coarse sand : 3 - 20 mm graded stone aggregate) in plinth protection and finished the surface even and smooth without using extra cement.

M& L Rendering 10 mm thick cement plaster in 1 : 1 : 2 (1 cement : 1 coarse sand : 2 fine sand ) cement mortar. On ceiling of concrete surfaces and rendering is to be finished even and smooth without using extra cement.

M&L, Rendering 15 mm thick cement plaster in 1:4 cement mortar(1 cement:4 coarse sand) on brick walls or concrete surfaces and render is to be finished even and smooth without using extra cement.

M&L 3 mm thick Acrylic sheet, white clear and transperant sheet fixed in aluminium windows / ventilators, fixed in position using screws / beading , as decided by the Engineer-in-Charge.

M&L two or more coats with oil bound distemper on ceiling including preparation of surfaces primer etc. complete as directed by Engineer-in- Charge

M& L & two or more coat of oil bound washable distemper over walls. including preparation of surfaces primer etc. complete as directed by Engineer-in- Charge

M& L Preparing steel surfaces of any description and applying one coat of red oxide primer and two or more coats of approved synthetic enamel paint including preparation of surfaces complete as directed by Engineer-in- Charge

Providing, fixing and testing PVC (SWR) pipes 110 mm bore single socketed in any length with rubber ring joints , laid in trenches or in floors.

Providing, fixing and testing, fixed to walls PVC (SWR) pipes 110 mm bore single socketed in any length with rubber ring joints.

Supplying and fixing 110 mm bore PVC (SWR) bends.

Supplying and fixing 110 mm bore door bends of PVC (SWR) .

Supplying and fixing 110 mm bore PVC (SWR) couplers.

Supplying and fixing 110 mm bore PVC (SWR) branch pieces single (equal or unequal), ordinary or inverted or with parallel branches.

Supplying and fixing 110 mm bore PVC (SWR) junction single ( single T) equal or unequal

Material and Labour, 110 mm bore PVC (SWR) multi floor trap with grating of chromium plated including jointing to waste pipe with solvent cement.

Providing and fixing PVC (SWR) gully trap 125/110 mm, setting and jointing with solvent cement.

Providing and laying integral cement based water proofing treatment including preparation of surface as required for treatment of roofs, balconies, terraces etc consisting of following operations :a) Applying a slurry coat of neat cement using 2.75 kg/sqm of cement admixed with water proofing compound conforming to IS 2645 and approved by Engineer-in-charge over the RCC slab including adjoining wall upto 300 mm height including cleaning the surface before treatment . b) laying brick bats with mortar using broken bricks/brick bats 25 mm to 115 mm size with 50% of cement mortar 1:5 ( 1 cement :5 coarse sand) admixed with water proofing compound conforming to IS : 2645 and approved by Engineer-n-charge over 20 mm thick layer of cement mortar of mix 1:5(1 cement :5 coarse sand ) admixed with water proofing compound conforming to IS : 2645 by Engineer –in- charge to required slope and treating similarly the adjoining walls upto 300 mm height including rounding of junctions of walls and slabs C). After two days of proper curing applying a second coat of cement slurry using 2.75 kg/sqm of cement admixed joint less cement mortar of mix 1:4 ( 1 cement : 4 coarse sand ) admixed with water proofing compound conforming to IS :2645 and approved by Engineer-in-charge including laying glass fibre cloth of approved quality in top layer of plaster and finally finishing the surfaces with trowel with neat cement slurry and making pattern of 300x300 mm square 3 mm deep. E) the whole terrace so finished shall be flooded with water for a minimum period of two weeks for curing and for final test . All above operations to be done in order and as directed and specified by the Engineer-in-charge, with average thickness of 120 mm and minimum thickness at khurra as 65 mm.

Making khurras 45 cm × 45 cm with average minimum thickness of 5 cm cement concrete 1 : 2 :4 Type B-0 using 12.5 mm graded stone aggregate over PVC sheet 1 mt × 1 mt × 400 micron, finished with 12 mm cement plaster 1 : 3 and a coat of neat cement rounding the edges and making and finishing the outlet complete.

Providing and fixing white vitreous china water closet (pedestal pattern) including seat cover,flush pipe, 'P' or 'S' trap,PVC valveless, symphonic action type flushing cistern of 10 ltr capacity low level, with inlet ball valve, float and handle including brackets and necessary water jet arrangements complete all as directed by Engineer-in- Charge.

Providing and fixing 15 mm C.P. brass stop valve (concealed type) with C.P. brass connection pipe with union nuts complete with C.P. brass flange (Parko or approved equivalent) including cutting and making good the walls where ever required.

Providing and fixing 15 mm C.P. brass angle valve with C.P. brass connection pipe with union nuts complete with C.P. brass flange (Parko or approved equivalent) including cutting and making good the walls where ever required.

Providing and fixing white/ glazed vitreous china wash basins flat back, size 630 x 450 mm including waste fittings ,waste pipe ,chain and plugs and porcelain stopper and brackets complete.

Providing and fixing 15 mm dia CP brass long body bib tap Parko or approved equivalent including cutting and making good the wall wherever required.

Providing and fixing 15 mm dia CP brass piller tap Parko or approved equivalent including cutting and making good the wall wherever required.

Providing and fixing 600 x 20 mm size C.P. brass towel rails Parko complete with C.P. brass brackets fixed to rawl plug of approved design with C.P. brass screws.

S/F fency type chromium plated soap dish any type fixed to plugs with CP brass screwes

Providing and fixing wall to wall 6 mm copper backed float glass mirrors complete with 6 mm thick BWP type ply board, 40 mm stainless steel channel plugged to wall, with hard wood treated with two coats of wood preservative etc. all complete.

Supplying and fixing 110 mm bore PVC(SWR) vent cowls.

Supplying and fixing stack clamp out of 25 mm × 4 mm flat iron and 12 mm dia round iron stays for 100 mm bore including bolts and nuts and securing and of stays to wall

Material and Labour, PVC (SWR) floor trap 110 mm bore , plain with grating including jointing with solvent cement.

Providing and fixing chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot and cold water supply, including all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer-in-charge.

20 mm nominal bore

25 mm nominal bore.

40 mm nominal bore

Providing and fixing 25 mm nominal bore ball valves with plastic float.

Providing and fixing 500 ltr capacity HPDE over head tanks including hoisting at desired height complete with inter connection pipes and all inlet outlets over flow scour connection all as directed by Engineer-in-Charge.

Providing and fixing salt glazed stoneware gully traps, square or round mouthed type "P". a) size of gully traps 180 x 150 mm

Supplying of SFRC Manhole covers & frames conforming to IS – 12592 (Part I) using M-35 concrete having clear opening of 560 mm dia as per details below (a)Medium Duty: Over all Total Size in height mm mm Frame Details 770 110 Cover Details 670 60

Material and labour anti termite treatment for treating the top surface of filled earth @ 5.00 ltr of Chlorophyriphos 20% of EC emulsion per sqmeter of surface.

Material and labour, Anti termite treatment for treating the soil under plinth protection @ 5 Ltr of Chlorphyriphos 20% of EC emulsion per sqmt of surface area.

Material and labour anti termite treatment for treating the bottom and sides of excavation @ 5.00 Ltr of Chlorphyriphos 20% of EC emulsion per sqmt of surface area.

Material and labour, Anti termite treatment for treating the back fill in contact with foundation at the rate of 7.5 Ltrs of emulsion per square meter of verticals surface.

Providing & laying in position Ready mix concrete M-10 grade, machine batched, machine mixed, design mix concrete (excluding the cost of centering and shuttering,) placing in position, mechanical vibrated and finished including addition of admixtures in recommended portions (as per IS-9103) to accelerate/retard setting of concrete to improve work ability without tampering strength and durability laid to required slope and camber in panels as directed in accordance with IS 456-2000,transported to the site of work from approved RMC plant . APPROVED MAKES : ND Con, Alcon, Techno, Spectrum, Orbit build tech, SS RMC, Raj Ready concrete, Metro, Shri Ram Cement concrete, L&T, Birla, Unitec, RDC, ACC, JK, Shaila, Empee con or having plant of minimum capacity of 60 cumt/and turn over should be minimum Rs. One crore per month or 4000 cum/month from the last one year upto proceeding month of opening tender. Contractor to submit procurement vouchers along with the bill. Note : (i) Contractor to submit Tax paid vouchers of RMC M-10 obtained form approved manufactures for claim of item in RAR/ Final bill. (ii) Contractor to submit manufacturer certificate certifying that M-10 quality concrete conforming provisions of IS- 456-2000 has been supplied to the designated site.

Providing & laying in position Ready mix concrete M-25 grade, machine batched, machine mixed, design mix concrete (excluding the cost of centering and shuttering,) placing in position, mechanical vibrated and finished including addition of admixtures in recommended portions (as per IS-9103) to accelerate/retard setting of concrete to improve work ability without tampering strength and durability laid to required slope and camber in panels as directed in accordance with IS 456-2000,transported to the site of work from approved RMC plant . Approved makes ND Con, Alcon, Techno, Spectrum, Orbit build tech, SS RMC, Raj Ready concrete, Metro, Shri Ram Cement concrete, L&T, Birla, Unitec, RDC, ACC, JK, Shaila, Empee con or having plant of minimum capacity of 60 cumt/and turn over should be minimum Rs. One crore per month or 4000 cum/month from the last one year upto proceeding month of opening tender. Purchase bills to be submitted for claiming of payment by the contractor. Note : (i) Contractor to submit Tax paid vouchers of RMC M-25 obtained form approved manufactures for claim of item in RAR/ Final bill. (ii) Contractor to submit manufacturer certificate certifying that M-25 quality concrete conforming provisions of IS 456-2000 has been supplied to the designated site.

Preparing P.O.P. surfaces and applying two or more coats of plastic emulsion of exterior grade over a coat of cement primer over walls and ceilings upto the entire satisfaction of Engineer-in-Charge.

S & F, sheet metal enclosures for MCB's

12way with 100 amps rated bus- bar double door type

8 way with 100 amps rated bus- bar double door type

S & F, MCB single pole 6 to 30 Amps, 240 volts (9 KA)

S & F, ELCB ,Double Pole 63 Amps

Supply, receiving, storing, handling, fixing, wiring for sub mains work using 1100 V grade, PVC insulated, Cu conductor wiring cable of following size drawn in rigid UPVC conduits 2mm wall thickness (ISI marked), in surface/ concealed system complete with all conduit accessories such as identification ferrules etc. as per specification, conduit being laid either in slab or wall chase including making & filling chases with cement mortar/ partition/ above false ceiling with hanging support wherever required as shown in the relevant drawing.

2x4.0 sqm +1x2.5 sqm copper wire, PVC insulated in PVC conduit 25m dia

S& Fixing Single pole & netral sheet metal enclosure for DB’s, 2 way without bus bar

Providing and fixing circular/ hexagonal MS sheet ceiling fan box with clamps of internal dia, 140 mm, 73 mm height, 3 mm thick rim, top and bottom lid of 1.5 mm MS sheet. Lids shall be screwed into MS box by means of 3 mm round headed screws, clamps shall be made of 12 mm dia MS bar bent to shape as per standard drawing and over all length as 80 cm.

POINT WIRING M& L Wiring for one light point/fan point/exhaust fan point/ call bell point with 1.5 sq. mm. PVC insulated, copper conductor wiring cable (including 1.5 sq. mm. PVC insulated, copper conductor wiring cable for earthing from switch board to each point) in surface /recessed non-metalic UPVC conduit 2 mm. wall thickness (ISI Mark) with metal box and hylem sheet including circuit wiring from the existing distribution board to switchboard with 3 x 1.5 sq. mm. PVC insulated, copper conductor wiring cable (one wire for earthing) and complete as required.

M&L Wiring for one 6 pin socket outlet 5/15 independent in surface/recessed non-metallic UPVC conduit 2mm wall thickness ( ISI marked ) with metal box and hylemsheet including circuit wiring from the distribution Board to switch board with 2x4 Sqmm and 2.5. sqmm copper cable for earth and complete as required.

M& L Wiring for 32 Amp metal clad socket outlet with 32 Amp MCB with 6 sq.mm. PVC insulated copper conductor wiring/ cable wire in rigid non metallic PVC conduit 2mm wall thickness (ISI marked) including 2.5 sq mm copper wire for earthing for Air Conditioning including supply of metal clad socket & MCB.

S&F tube light grade 100mm dia Galvanized iron for passing electric or telephone cable with all fittings laid in trenches.

M & L PVC insulated, armoured heavy duty electric cable with aluminum conductor 1100 volts grade cross section area 95x4sqm core to be laid from NDPL pole to main panel as specified

M&L PVC insulated armoured heavy duty cable with aluminium conductor 1100 v grade cross sectional area 50x4sqmt

M&L Bell AC, 230v single pole complete all as specified

S &F 1100 volt grade heavy duty cable PVC insulated aluminum conductor, served with inner sheathing of PVC tape and over all PVC sheathed in service connection suspended by insulating hangers not more than IM apart including 4mm suspension wire one twin core cable 2x10 mmsq.

S & F non metalic PVC conduit exclusive of junction and terminal boxes but inclusive of all fittings such as tees, bends, elbows, reducers and all fixing accessories such as coupler, lock nuts, saddles pipe hooks etc.

for 25mm dia conduit pipe.

Supplying and fixing switch piano flush button, single pole one way 5 Amp.

Supplying and fixing switch piano flush button Single pole one way. 15 Amp.

Supplying and fixing socket outlet 6 pin, 5 / 15 Amp (combined) flush type.

Supplying and fixing , ceiling rose surface Bakelite, 65x50 mm two or three terminals (using for exhaust fan).

S/F of socket outlet for TV including laminated sheet box etc. complete

S/F of socket outlet for computer including laminated sheet and box etc complete all as specified and directed by Engineer-in-charge.

Supplying and fixing cast iron/ pressed steel terminal boxes for mounting switches sockets, fan regulators etc. with 3 mm thick plastic laminated sheet cover for the following sizes.

150 mm x 100 mm

200 mm x 100 mm

200 mm x 300 mm

250 mm x 300 mm

S/F bulk head, light fitting flame proof with built in control gear box made of aluminum alloy inclduing LED bulb and other accessories and internally prewired.

S&F of multi LED, high efficient light fittings of 150 watts with pressure die cast aluminum housing reflector enclosed with toughened glass with all accessories for fixing on 50 mm dia bracket with IP-66 protection complete accessories all as specified and directed by Engineer –in- Charge.

S/F light fitting single tube 1x20 watts, 230 volt and 1200 mm long spray power coated , bipin holder, complete with all accessories, prewired and including connnecting up with twin core twisted flexible copper conductor cable of suitable size.

S&F Bracket made out of G.I.pipe medium grade 50 mm dia, and 1 metre length bend at 120 “ suitable for mount LED light fitting of 120 watt and embeded in CC pillar using 1:2:4 type B-1 all as specified as directed by Engineer –in- Charge

Supplying and fixing 1200 mm sweep ceiling fan with step type electronic fan regulator .

Supplying and fixing 400 mm sweep exhaust fan with out regulator .

Supplying and fixing 400 mm sweep cabin fan (Wall Mounted).

Wiring with lan cable of copper conductor 1.0sqm size in the existing PVC conduct on surface or received as specified directed by Engineer-in-charge.

Wiring with TV cable RJ-6 of copper conductor in existing PVC conduit on surface or released including TV connecting plug as specified and directed by Engineer –in-Charge

M&L ,Providing earthing as per IS 3043 complete with galvanized steel earth plate electrode 60 x 60 cm x 6.3 mm thick buried directly in ground. (earth pit not less than 2.25 mt below normal ground level). With top edge of the plate not less than 1.5 mt below normal ground level, connected to galvanized earth lead wire 4 mm dia by means of bolts, nuts, check nuts and washers of galvanized iron or steel all as shown in electrical plate No.5, connected to earthing test point including earth pit with Cl COVER all as specified or indicated and testing on completion.

600 x 600 x 6.3 mm GI Plate Earth Station.

600 x 600 x 3.15 mm Copper Plate Earth Station.

S& F Earth continuity conductor or main earthing lead fixed to wall on batten or recess or chase or burried in ground or drawn in conduit/pipe or fixed to holes or at any other indicated situations for loop earthing etc as required 25 × 4 mm galvanized iron strips

S&F of socket outlet, three pin 5 Amp on the same Board, with other switches in PVC conduit with PVC insulated cooper cable of size 1.5 sqmt.

S&F of socket outlet, threepin 5 Amps, independent with switch Board in PVC conduit and copper cable of size 1.5 sq

Providing & fixing self contained drinking water cooler with CFC refrigerator energy efficient compressor 150Ltrs storage capacity including connection to water main/pipe and electric connections complete, as specified, Voltas, Usha, Sidwal.

Lamp holder PVC/Poly carbonate by with cord grib suitable for batten fitting including LED bulb of make siska, Havel as specified and directed .

M/s. Kansal Construction Co.