SPL REPAIR TO VSK CENTRE LOCATED AT 21 SUB AREA CSD COMPLEX, SPL REPAIR TO KOTA STONE AND TILING WORK OF CHILDREN SCHOOL AND ADDL/ALTN OF TOILET BLOCK and VETERANSWAITING AREA AT VSK CENTER UNDER GE (WEST) PATHANKOT

Amount

Demolition of brick work , built in cement mortar or cement lime mortar including all quions, arches, pillars, etc including demolition of precast rcc articles and disposal of debris out of MoD land complete all as specified and directed.

Dismantling of Stone slabs & tiles of any description or thickness in floors, aprons etc. Laid, bedded & pointed in any mortar complete all as specified and directed.

Demolition of cement concrete or lime concrete (unreinforced) in ground floors and pavings not exc 15 cm thick (below or above ground level) and removing the debris outside from defence land, complete all as specified and as directed.

Dismantling timber scantling 40 Sqcm and over in section, in any position as in wooden trusses in framed work of any discription.

Demolition of reinforced concrete of any discription and in any position not otherwise specifiaclly provided for complete all as specified and as directed.

Taking down Asbestos cement (corrugated, semicorrugated, etc.) sheets in roof coverings any type complete all as specifioed and as directed by Engr-in-Charge.

S&F Pre- painted galvalume aluminum zinc coating AZ-150 GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified complete all as specified and directe

S&F Pre- painted galvalume aluminum zinc coating AZ-150 GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified complete all as specified and directe

Surface dressing in loose / soft soil n exc 15 cm deep complete all as specified and as directed.

Surface excavation in hard/dense soil n.exc (not exceeding) 30 cm deep and averaging 15cm deep and getting out

Excavating over areas, n exc 1.5 m deep and getting out in loose / soft soil complete all as specified and as directed.

Excavating in hard/dense soil in trenches, n exc 1.5 m wide and n exc 1.5 m in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. n exc 10 sq m on plan and n exc 1.5 m in depth and getting out

Returning filling in including spreading leveling, watering and well ramming in layers not exc 25 cm in soft/loose soil complete all as specified and as directed.

Removing excavated materials( soil) obtained from excavation to a distance not exceeding 50 mtr and depositing where directed at a level not exceeding 1.5 mtr above the starting point complete all as specified and as directed.

M&L for hard core of broken stones or boulders of gauge not exc 63mm, deposited, spread and levelled in layers not exc. 15 cm thick, watered and rammed to a true surface complete all as specified and directed

M&L for PCC 1:2:4, type B-0, (using 12.5 mm graded crushed stone aggregate) including mixed with water proofing compound as per manufacturer’s instructions as in padding on roof, surface finished even and smooth without using extra cement all as specified and as directed.

M&L for 75mm thick Plain Cement Concrete type D-2, 1:3:6 (using 20 mm graded stone aggregate) as in Plinth protection complete all as specified and as directed.

M&L for 75mm thick Cement concrete in sub base using type D-2, 1:4:8 (using 40 mm graded crushed stone aggregate) Finishing surfaces of concrete to be even and rough to receive the topping layer or floor tiles etc complete all as specified and directed.

M&L for 100mm thick Cement concrete in sub base using type D-2, 1:4:8 (using 40 mm graded crushed stone aggregate) Finishing surfaces of concrete to be even and rough to receive the topping layer or floor etc complete all as specified and directed.

M&L for Plain Cement Concrete Type D-2, 1:4:8 (using 40 mm graded crushed stone aggregate) in foundations, filling and mass concrete complete all as specified and as directed.

M&L for 25mm thick Cement concrete in sub base for receiving floor tiles and sub base using type B-1, 1:2:4 (using 20 mm graded crushed stone aggregate) Finishing surfaces of concrete to be even and rough complete all as specified and directed.

M&L Reinforce cement concrete M-25 (Designmix) Foundations, including rafts, footings, foundation beams; plinth beams; bases for columns, etc.; basement slabs, under-reamed piles and mass concrete complete all as specified and as directed.

M&L Reinforce cement concrete M-25 (Design mix) as in Slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like complete all as specified and as directed.

M&L Reinforce cement concrete M-25 (Design mix) as in Beams, cantilevers, bressummers, lintels over 1.5m span complete all as specified and as directed.

M&L Reinforce cement concrete M-25 (Design mix) as in Columns, pillars, piers, posts and struts complete all as specified and as directed.

M&L for Providing factory precast cement concrete type B1 1:2:4 (using 20 mm graded crushed stone aggrgate) as in landings, cover slabs (for man holes etc.) chullah hoods, chajjas, water troughs, mangers, shelves and similar articles with plain faces

Formwork to sides of concrete foundations, footings, bases of columns, rafts raft beams, sides and soffits ( if any ) of foundation and plinth beams; and similar work; vertical or batter, finished rough surfaces of concrete, complete all as specified and directed.

Formwork to Square, rectangular or polygonal sides of pillars, posts, struts, piers, columns and stanchions complete all as specified and as directed.

Formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings & similar work; not exc. 200mm thick (Horizontal or sloping) Rough finished surfaces of concrete flat complete all as specified and as directed

Formwork to sides and soffits of floor or roof beams, beam haunch ings, girders, bressummers, lintels, cantilevers, shelves including sup- ports, overhangs, etc. also splays between floors and beams, etc.complete all as specified and as directed.

M&L for brick work with sub class 'B' Bricks (using old size bricks) straight or curved on plan exc 6m mean radius, built in CM 1:4, complete all as specified and as directed.

M&L for brick work with sub class 'B' Bricks (using old size bricks) straight or curved on plan exc 6m mean radius, built in CM 1:6, complete all as specified and as directed.

M&L for Rendering 10 mm thick on fair faces of brick work or concrete surfaces wall in cm 1:6 to be finished even and smooth (without using extra cement) complete all as specified and as directed.

M&L for Rendering 15mm thick on fair faces of brick work or concrete surfaces of wall in cm 1:4 (mixing with water proofing compound as per manufacturer instruction) to be finished even and smooth without using extra cement complete all as specified and as directed. Note:-WPC shall be measured and paid separately.

M&L for Rendering 15mm thick on fair faces of brick work or concrete surfaces wall in cm 1:6 to be finished even and smooth (without using extra cement) complete all as specified and as directed.

M&L for Rendering 15mm thick on fair faces of brick work or concrete surfaces of wall in cm 1:4 to be (mixing with water proofing compound as per manufacturer instruction) to be finished even and smooth (without using extra cement) complete all as specified and as directed.

M&L for Rendering 5mm thick on fair faces of brick work or concrete surfaces in ceiling in cm 1:3 to be finished even and smooth (without using extra cement) complete all as specified and as directed.

Supply only 'Liquid water proofing compound' of approved make/brand

M&L for repair to chajjas, roof projection and facias of exposed reinforcement surface or damaged loose RCC surface including cutting down rusted/exposed reinforcement and applying one coat of cement slurry and filling with cement concrete 1:2:4 type B-0 (using 12.5 mm graded crushed stone aggregate) and finished with cement mortar 1:3 using coarse sand with mixing of liquid water proofing compound @2% by weight of cement or as per manufacturer instruction. Thickness of RCC member not exc 150 mm including scaffolding up to 8.0m height complete all as specified and as directed . Note : (i) No extra rates of scafffolding will be paid separately against this item. (ii) Water proofing compound will me measured and paid sepratly.

M&L for preparation of newly plaster surfaces of walls and applying two coats of oil bound distemper over a priming coat of chalk whiting, on plastered surfaces, preparatory to distempring complete all as specified.

M&L for preparation of newly plaster surfaces of walls and applying two coats of cement base paint over a priming coat of alkalies resistance priming paint complete all as specified.

M&L for preparation of newly plaster surfaces of walls and applying three coats of white wash on ceiling complete all as specified and as directed.

M&L for preparation of newly plaster surfaces of walls and applying two coats of oil bound distemper over Providing and applying plaster of paris putty of 1 mm thickness over plastered surface to prepare the surface even and smooth and a priming coat of primer, on plastered surfaces, preparatory to distempring complete all as specified.

M&L for applying Two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over new surfaces.

M&L for 2mm thick wall care putty (make approved by the Engg-in-charge) over plastered surfaces and make even with rubbing by sand paper till satisfaction of Engineer-in-charge complete all as specified and as directed.

M&L for machine cut kota stone slab flooring 18-20mm thick over cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and mirror polishing complete over screed bed or bedding layer 20 mm thick in cement mortar 1:4, complete all as specified and directed. Note:- Rate included for all cutting ,waste including machine cutting to make it square or rectangular,cutting and polishing by machine & size of kota stone shall not be less than 550 mmx550mm .

M&L for factory made Machine pressed precast concrete interlocking paver block any shape and size confirming to IS 15658-2006 of 60 mm thickness, M-35 Grade with grey Cement and pigment, including 50mm thick sand cushioning bed complete all as secified and directed. Note:-Laying pattern and colour should be approved by the GE.

S&F Rolled mild steel Fe 410-W (Gde E- 250) quality A in Roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc.soil, complete all as specified and directe

M&L for mild steel Framed work such as grills, gratings, etc.. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe.290.Gde-E-165

M&L for Preparation of new or previously untreated surfaces of any description, over 10cm in width or girth,not otherwise described priming with red oxide, zinc chrome and applying two coat of synthetic enamel paint soil, complete all as specified and directed.

M&L for Mild steel TMT bars 10mm dia & over,cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends & binding with & including mild steel wire (annealed) not less than 0.9mm dia or securing with clips quality complete all as specified and as directed.

M&L for Mild steel TMT bars 6mm to 8mm dia & over,cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends & binding with & including mild steel wire (annealed) not less than 0.9mm dia or securing with clips quality complete all as specified and as directed.

M&L for Mild steel TMT bars 5mm dia and over upto and including 10mm dia in stirrups, spacers and binders,cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends & binding with & including mild steel wire (annealed) not less than 0.9mm dia or securing with clips quality complete all as specified and as directed.

S&F Cast iron rainwater socketed pipes 100mm dia with cement joints, with/without ears and as directed.

M&L for (Double charged) light shade Virified Ceramic tiles 10 mm thick (square/ rectangular) polished, area of each tiles exceeding 0.42 sqm and n exc 1.00 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match including 15mm thick screed bed in CM 1:4 all complete at all heights as per direction of Engineer-in-Charge.

M&L for (Double charged) light shade Virified Ceramic tiles 10 mm thick (square/ rectangular) polished, area of each tiles not exceeding 0.36 sqm, as in skerting etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match including 10mm thick plaster in CM 1:3 all complete at all heights as per direction of Engineer-in-Charge

Taking down existing Wall and ceiling boards (fibre, pulp, insulation, etc.) or insulation boards/slabs/ blankets, any thickness, including cover fillets complete all as specified and as directed .

S&F false ceiling with fibre cement designer tiles ivory painted (high pressure steam cured) of 4mm thickness (as per IS:14862) of size 595 x 595 mm and any one of the design (occeanic, lake & hill, cascade or electra) in true horizontal level, suspended on interlocking metal grid of hot dipped galvanized steel sections (galvanized @ 120 gms, both side inclusive) consisting of main 'T' runnerwith suitably spaceed joints to get required length, and 15x32 mm made of 0.30 mm sheet, and cross 'T' at 600 mm c/c to form a grid including, required cutting/making, opening for services like diffusers, grills, light fittings, fixtures, smoke detectors etc. Main 'T' runners to be suspended from ceiling using GI soffit cleats fixed to exising rafter, purlin, etc with galvanised butterfly level clips, spaced at 1200 mm c/c along main T, bottom exposed width of 15 mm of all T-sections shall be centra black pre-painted with polyester paint, and havng a load bearing capacity of 12Kg/sqm, and refixed all existing electric wiring and fixture all complete at all heights as per direction of Engineer-in-Charge

Taking down chowkhats or frames exc 1.50 and n.exc 4 Sqm each (without talking off shutters from the freme) complete all as specified and directed.

M&L for Powder coated (of approved color) aluminium sections as in frame & shutter of windows, ventilators as in sliding / openable / louvers / fixed type with and including necessary rolling for smooth moving & locking arrangement, etc. fixed to wall including, preparation of disturbed portion both sides (internal & external surfaceof wall) match with existing surface treatment and all sides of aluminium frame shall be sealed with silicon sealent (inner/outer face) complete all as specified as directed by Engr-in-charge.

S&F 125mm size,extruded aluminium alloy handles, fabricated type anodised complete all as specified and as directed.

S&F 5.5 mm thick tinted sheet glass figured, pin head type or-dinary quality and glazing with rubber neoprene packing for aluminium door/windows in square n exc 0.5 sq. m in each pane, complete all as specified and as directed.

S&F 5.5 mm thick tinted sheet glass figured, pin head type or-dinary quality and glazing with rubber neoprene packing for aluminium door/windows in square exc 0.5 sq. m in each pane, complete all as specified and as directed.

Toughened and tampered glass panes including unframed assemblies (such as frameless door/windows) comprising of 12 mm thick glass pressed by controlled thermal of chemical treatments to increase its strength compared with normal glass conforming to IS 2553 Part-I to be fitted as per manufacturers instructions complete all as specified and as directed by Engr-in-charge. Note: (1) No cutting and griding of glass shall be allowed as site of work and the contractore shall procure actual size required as site in consultatio with Engr-in charge prior to placing order for the same. (2) Rate is inclusive of all fittings such as suitable heavy duty hydraulic floor spring, top and bottom hinges, aluminium bow handels, fancy type, 02 Nos on each shutter and fixtures as required at site.

S&F stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.18mm and fixed with stainless steel wire staples or using metal nut and bolts complete all as specified and directed.

M&L liquid water proofing treatment to RCC roof slab including dismantling of existing roof treatment of any description such as worn-out tar felt, debris, mortar of any description & any thickness, surface cleaning of all foreign material such as shrubs/roots, fungus, moss, dust including plaster, APP membrane etc. including disposal of debris out of MoD land, in following procedure : (a) Laying 10mm thick rendering in Cement mortar 1:3 with liquid water proofing compound (as per manufacturer’s instructions) on fair faces of concrete roof surfaces, finished even and fair to receive treatment on roof Complete (b) Applying first coat fiber reinforced elastometic liquid water proofing membrane formulated with PU hybrid polymers and reinforcing acrylic fibers with sun reflective index (SRI) of 100-110, having minimum elongation of 350%, tensile strength 2.9 Mpa and shall have crack bridging ability upto 2.5mm and shall resist 10 bars of hydrostatic pressure reduce surface temperature upto 10 degree celsius with 3.3% dilution as priming coat (c) laying of fiber mesh 0.3mm thickness weave in leno pattern having weight 4.5 gm/ Sqm and pasting it properly with overlap of 50mm and allow it to dry (d) Applying second coat undiluted @ 0.45 ltr/ sqm as directed by Engr-in-Charge (e) Applying third and final coat undiluted @ 0.45 ltr/ sqm as directed by Engr-in-Charge. Note: The rate includes for filling cracks in existing roof with cement putty using suitable bonding agent (shalcrate 42) before laying cement plaster. ”

S&F non skid coloured Ceramic tiles 08mm to 10mm thick (square/ rectangular) polished, area of each tiles exceeding 0.11 Sqm but not exceeding 0.18 Sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15mm thick screed bed in CM 1:4 complete all as specified and directed. Note:-The texture ,colour ,Shade of tiles & laying of tiles to any pattern & any design with one or more colours shall be approved by GE and Rates also including in this item for necessary raking circular cutting or notching and waste on tiles.

M&L for coloured Glazed ceramic tiles in vertical surface such as dado etc 450mmX 300mmX 7 to 8mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match the shade of the tiles over and including 10mm thick rough cement plaster to receive tiles in CM 1:4 complete all as specified and as directed. Note:-The texture ,colour ,Shade of tiles & laying of tiles to any pattern & any design with one or more colours shall be approved by GE and Rates also including in this item for necessary raking circular cutting or notching and waste on tiles.

M&L for wall cladding in vertical surface such as dado etc of size of tile 450mmX 300mmX 7-8 mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match the shade of the tiles over and including 10mm thick rough cement plaster to receive tiles in CM 1:3 complete all as specified and as directed. Note:-The texture ,colour ,Shade of tiles & laying of tiles to any pattern & any design with one or more colours shall be approved by GE and Rates also including in this item for necessary raking circular cutting or notching and waste on tiles.

Cutting chases in brick walls, pinning in, making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, shelves, lintels, etc, and cutting chases for concealed water tubing or conduit wiring, etc and making good, cutting not exceeding 10cm girth complete all as specified and directed

S&F 15mm bore Steel water tubing 'medium grade', galvanised with all fittings like elbow, tee, socket, bend etc and fixed to wall, ceiling or laid in floor complete all as specified and directed.

S&F Vitreous China wash down water closet pan including P or S trap of bore 125/110 mm (pedestal pattern), white or in matching colour of tiles (excluding flushing cistern and flush pipe) including plastic water closet seat, white or in matching colour , closed pattern with flat bottom, and cover and mild steel chromium plated or aluminised hinging device and wash down water closet complete all as specified and as directed.

S&F viterous China squatting pan, `Orrisa' pattern, size 580 x440 mm white, witht integral foot rests (excluding flushing cistern and flush pipe) including connection to trap,and to flushing pipe, anti-syphonage pipe,etc. complete including making good to floor complete all as specified and as directed.

S&F Viterous China wash basin, white, flat back, size 550x400mm excluding taps etc but including brackets,including cutting for and pinning in ends of brackets or erecting stand including fixing of PVC cnnection and waste pipe complete all as specfied and as directed.

S&F Vitreous China Urinal, Half stall type, white including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including 60mm long brass screws, pointing around urinal back in cement, , flush pipe, grating and union for discharge pipe (excluding flushing cistern, flush pipe and waste pipe) fixed incl supply and fixing of CP coupling, waste pipe and cp brass spreder all necessary fittings, complete all as specified and directed.

S&F Urinal spreader of PTMT any colour for fixing with 15 mm dia pipe. (Minimum weight 60gms)

S&F Vitreous china urinal partition white of size 310x700 mm.

S&F Brass CP towel rail 20mm dia 'D' type 60 cm long between flanges complete all as specified and directed.

S&F 10 ltrs capacity PVC valveless, syphonic action type, flushing cistern, low level, white, with intel, ball valve, float and handle including brackets ,fush pipe of polyethylene of low or high density or PVC 32 mm dia complete all as specfied and as directed.

S&F 15mm dia 600 mm long PVC connection including brass check nut at both ends screwed both end for iron pipes.

S&F Pillar taps fancy type cast copper alloy chromium plated with capstan head without letter Hot or Cold water screwed down for 15 mm dia iron pipe complete all as specified and as directed.

S & F 15mm bore dia of pipe bib taps cast copper alloy, fancy type chromium plated, with capstan head screwed down, high pressure screwed for iron pipe or brass ferrule complete all as specified and as directed.

S & F stop valve / angle cock fancy type cast copper alloy chromium plated with long shank and cup(concealed type) capstan head serewed down, high pressure for 15 mm dia iron pipe complete all as specified and as directed.

S & F brass chromium plated health faucet with 1m long PVC tube & wall hook. screwed for 15mm dia bore iron pipe or 2 in one tap complete all as specified and as directed. Make: ALD -563 Jaquar or equivalent in any of the make mentioned in list of product complete all as specified and as directed.

S & F brass chromium plated toilet roll holder with flap complete all as specified and as directed. Make : AKP - 35753P of Jaquar or equivalent in any of the make mentioned in list of product.

S & F CP Grating with hole /with out hole of dia 125 mm complete all as specified and as directed.

S & F factory made solid panel PVC door shutter 30mm thick (style) consisting of frame made out of MS tubes for top and bottom rails MS frame shall be coucred with heat moulded wood grain printed PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and wood grain printed PVC sheet for top rail, lock rail & bottom rail on either side as gap insert for top rail bottom rail panelling of wood grain printed PVC sheet to be fited in the MS frame welded/seald to the stiles & rails with suitable PVC sheet beading and jointed together with solvent cement suppling & fixed in the framed site as per specification & drawing complete all as specified and as directed.

S & F PVC door frame of size 50mmx47mm made out of 5mm wood grain printed PVC sheet reiforced with MS squre tube as per specification and drawing complete all as specified and as directed.

S&F Anodised aluminium window and ventilator shutters, side hung type without sash bars, aluminium ections weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws, anodised aluminium fittings such as peg stays 150mm long (1 no.). hinges type B-21 100mm long (2 no.) suitable handle (1 no.) complete all as specified

S&F 250mm long Aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed

S & F aluminium anodised barrel tower bolts of extruded section 150mm long complete all as specified and as directed.

S & F 125mm size,extruded aluminium alloy handles, fabricated type anodised complete all as specified and as directed.

S & F 100 mm size butt hinges extruded aluminium alloy with galvanised mild steel hinges complete all as specified and as directed.

S & F 110 mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to walls complete all as directed.

S & F 110 mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints laid in trenches complete all as directed.

S & F 110 mm bore PVC (SWR) bends complete all as specified and as directed..

S & F 110 mm bore PVC (SWR) accessible door bends complete all as specified and as directed..

S & F 75/100mm PVC(SWR) floor trap plain with grating incl jointing with solvent cement complete all as specified and as directed.

S & F 5 mm thick sheet glass figured, pin head type or-dinary quality and glazing with oil putty / beading in square n exc 0.5 sq. m in each pane, complete all as specified and as directed.

M&L for 18-20mm thick Granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, win dow-cills, cooking plat forms and like in cement mortar (1:4) including point ing in white cement (1:2) using marble dust with admix ture of pigment to match with shade of granite complete all as specified and as directed.

M & L for point wiring for one light/one fan controlled by one switch with 1.5 PVC insulated unsheathed multistrand copper conductor FRLS cable with and including PVC concealed conduit heavy duty suitable size with all fittings including anodise pressed steel sunken box with bakelite laminated sheet ISI marked for switches and sockets , including 1.5 sqmm PVC insulated unsheathed multistrand copper conductor FRLS cable as earth continuity conductor connected to comman earth dolly, including cutting chiseling for concealed piping and making good disturbed surface to match with the existing surface complete all as specified and directed.

All as per Srl item No 102 here-in-before but for 3 pin 5 amps socket outlet on the same board with other switch complete all as specified and directed.

M&L for modular point wiring for one light/one fan controlled by one switch with 1.5 Sqmm PVC insulated unsheathed multistrand copper conductor FRLS cable with and including PVC rigid concealed conduit heavy duty suitable size with all accessories including modular matallic flush box of suitable way with modular cover plate for modular switches and sockets , including green 1.5 sqmm PVC insulated unsheathed multistrand copper conductor FRLS cable as earth continuity conductor connected to comman earth dolly, including cutting chiseling for concealed piping and making good disturbed surface to match with the existing surface including taking down old u/s point wiring complete all as specified and directed.

All as per Srl item No. 104 here-in-before but modular 3 pin 5 Amps socket outlet on the independent board with other switch complete all as specified and directed.

All as per Srl item No. 104 here-in-before but modular 3 pin 5 Amps socket outlet on the same board with other switch complete all as specified and directed.

M&L for modular point wiring with 2.5 Sqmm PVC insulated unsheathed multistrand copper conductor FRLS cable with and including PVC rigid concealed conduit heavy duty suitable size with all accessories including modular matallic flush box of suitable way with modular cover plate for modular switches and sockets , including green 2.5 sqmm PVC insulated unsheathed multistrand copper conductor FRLS cable as earth continuity conductor connected to comman earth dolly, including cutting chiseling for concealed piping and making good disturbed surface to match with the existing surface including taking down old u/s point wiring complete all as specified and directed.

S&F switch piano flush type one way 5 amps SP 240 volts complete all as specified and directed.

S&F socket outlet 2 in 1, 3 pin 5 amps flush type 240 volts complete all as specified and directed.

S&F in repair Modular switch 1 way 6 A, 1 module complete all as specified and directed.

S&F in repair Modular switch 1 way 16A, 1 module complete all as specified and directed.

S&F in repair Modular Socket, 6A - 2/3 pin combined 2 module complete all as specified and directed.

S&F in repair Modular Socket 6A/16A - 2/3 pin combined 2 module complete all as specified and directed.

S&F in replacement of existing unsv sheet metal enclosure with sheet metal enclosure MCB distribution board single pole and neutral with a two pin and earth plug and socket 20 amps 240 volts, complete with one single pole MCB of 20 amps 'C' curve complete all as specified and directed .

S&F in repair ceiling rose 65 x 50mm three terminals complete all as specified and directed.

S&F in repair Modular Fan regulator 6A, 1 module , complete all as specified and directed.

S&F energy saving decorative 20W LED tube light box type frame , light fitting extruded PVC housing provided for efficient heat dissipation with polycarbonate diffuser & integrated electronic driver complete with all accessories prewired and making connections with 2 core twisted flexible copper cable of suitable size ceilling rose/PVC connector to light fittings complete all as spd and directed by Engr -in -charge.

S&F in replacement LED slim panel (2 in 1, cool white and warm white type) 12W LED ceiling round 6" light fitting 220 V AC recessed type with high efficiency PMMA diffuser soft glare free light complete with driver holder & LED Lamp suitable for roof ceiling including connecting up with driver three core flaxible copper conductor of suitable size from ceilling rose/PVC connector to light fittings complete all as spd and directed by Engr -in -charge.

S&F & testing ceiling fans complete with blades including fan remote, down rods, electronic regulator and accessories, 230 V, 1200 mm sweep. Min air delivery 210 CFM with service value 6.00 BEE. Five star rated with brushless direct current motor (BLDC) and connecting with flexible copper conductor of suitable size and including writing of MES No with black paint complete all as specified and as directed.

S&F in replacement of sheet metal enclosure MCB distribution board, double door with IP-43 protection single phase 240 volts 8 way, including suitable size copper bus bar and neutral link fixed flush in wall including chases in wall for fixing DB and making good the distributed wall surfaces to match with existing specification complete all as specified and directed.

S&F sheet metal enclosure MCB distribution board, double door with IP-43 protection single phase 240 volts 4 way, including suitable size copper bus bar and neutral link fixed flush in wall including chases in wall for fixing DB and making good the distributed wall surfaces to match with existing specification complete all as specified and directed.

M&L for MCB SP 240 volts any rating from 6 to 40 amps, 'C' cruve with rupturing capacity 10 KA, including providing thimble for out going cables complete all as specified and directed.

M&L for MCB SPN 240 volts any rating from 6 to 40 amps, 'C' cruve with rupturing capacity 10 KA, including providing thimble for out going cables complete all as specified and directed.

S&F in replacement bldg secuirty light fitting energy saving high efficiency LED street light fitting 35 Watts, 5700 K, IP 66, having pressure die cast housing with toughened glass and individual high power LEDs with secondary optics, prismatic polycarbonate cover complete including GI bracket of size 25 mm dia bent to shape having length on less than 0.9 mtr fixing with clamp etc and making connections using suitable size copper cable from ceilling rose/ PVC connector to light fittings or as directed by Engr-in-chrage.

S&F in replacement sub Main Wiring with two PVC insulated unsheathed multistrand FRLS flexible copper conductor cable of size 2x4 sqmm and one PVC insulated multistrand unsheathed FRLS flexible copper conductor cable of size 4 sqmm (green colour) as earthing lead connecting to main earthing dolly drawn in and including non metallic PVC concealed conduit 20mm dia complete and making good to disturbed surface complete of wall/floor with cement mortar and finishes to match the existing surface complete all as specified and directed.

S&F in replacement sub Main Wiring with two PVC insulated unsheathed multistrand FRLS flexible copper conductor cable of size 2x6 sqmm and one PVC insulated multistrand unsheathed FRLS flexible copper conductor cable of size 6 sqmm (green colour) as earthing lead connecting to main earthing dolly drawn in and including non metallic PVC concealed conduit 20mm dia complete and making good to disturbed surface complete of wall/floor with cement mortar and finishes to match the existing surface complete all as specified and directed.

S&F in replacement of old unsv sheet metal enclosures distribution boards, double door three phase 415 volts 4 ways vertical TPN DB for comprising three phase four wire copper strip bus bar of appropriate capacity complete all as specified and directed and comprising of the following (a) MCCB FOUR POLE 100 AMPS AC 415 VOLTS 25 KA=01 NO as incoming and 12 nos. MCB SP 40 Amps, C series as outgoing. ( (i) MCCB, MCB and DB should be of same make. (ii) The DB shall be flush fixed ,and making good the disturbed surface matching with existing specifications shall be part of job at no extra cost.(iii)connection of theMCCBs/ MCBs with cable shall be made through appropriate size pin /bottle type thimble -properly crimped.(iv) all the vacant holes of the DB shall be provided with blank plates of appropriate size. (v) double continuous earth wire shall be provided for each three phase DB from earthing mains dolly.

M&L for earthing complete with galvanised steel earth plate electrode , 600 x600 x 6mm thick burried directly in the ground (earth pit not less than 2.25 mtr deep below ground level)with top edge of the plate not less than 1.5mtr below ground level connected to galvanised iron wire 4mm dia as earth lead by means of bolts, nuts and washers of GI up to test point , GI tubing 15 mm bore light grade protection pipe , GI watering pipe 20mm bore light grade with funnel and wire mesh , charcoal ,salt packed around the earth plate and precast PCC 1:2:4 (Nominal mix ) reinforced with XPM having weight not less than 4 kg /sqm including suitable handle of 6mm dia MS bar and angle iron 40x40x3mm frame for cover including earth work in any type of soil , removal of surplus soil to a distance n.exc 50m and connecting , testing on completion complete all as shown on electric plate No 03 of SSR -2009 Part I complete all as specified and directed.(Note: Excavation and earth work is deemed to be included in the rates quoted).

M & L for providing/ cutting the round/ square hole of required size in wall finishing the distrubed surfaces as per existing finishes complete all as spd and supply and fixing MS ventilating fans Single phase, 230 volts 225 mm or 9” H.D EX Fan (900 RPM) complete and supply and grouting the ragged bolts in wall, fixing the frame on the exhaust side (outer surface of the wall) and connecting with and including PVC insulated three core 1.5 sqmm copper cable from ceiling rose to exhaust fan motor and writting MES No. with black synthetic enamel paint 2.0 cm high complete all as spd and directed by Engr-in-charge.

Supply, laying and testing in repair LT XLPE insulated, screened, PVC bedded, galvanised steel strip or wire armoured, electric power cable (heavy duty) with aluminium conductor, 1100 volts, grade cross sectional area 25 sq. mm 4 core complete all as specified

Supply, laying and testing LT XLPE insulated, screened, PVC bedded, galvanised steel strip or wire armoured, electric power cable (heavy duty) with aluminium conductor, 1100 volts, grade cross sectional area 10 sq. mm 2 core complete all as specified

Excavation in trenches not exceeding 1.5 m wide and not exceeding 1.5 m in depth and getting out in soft/loose soil for laying of cable ,pole foundation,stay,laying of pipe etc complete all as specified and directed.

M&L for sand cushioning to under ground cables with a layer of sand 8 cm before laying the cable and 15 cm after laying the cable complete all as specified (Note:-Punned thickness shall be measured and paid)

M&L for brick covering equal to length of bricks as mechanical protection to cable with well burnet sub class ‘B’ bricks laid as directed by the Engr-in-Charge.

S&F GI tubing light grade 50 mm bore for cable protection laid in trenches in road crossing or fixed to wall/Pole including fittings /clamp complete all as specified and directed.

S&F 20mm dia Gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed complete all as specified and as directed.

S&F tubes medium grade galvanized with all fittings and laid in tranches, floor, along with wall/ceiling etc. of 20mm bore including cutting chasing in walls, bend, clamps, nut bolts and washers etc. if required complete all as specified and directed.

Note:-The accepted amount will be arrived after deducting the Sch of credit i.e. Rs 39,879.00 and any other reduction if any from quoted amount.

M/S RUDRA CONSTRUCTION CO (BID ID -3357882)

OMKAR SHARMA AND CO (BID ID -3365979)

DABGOTRA BUILDERS (BID ID -3365238)

HARI OM ENTERPRISES (BID ID -3357999)

Substantial Const. Co. (BID ID -3366284)