Providing electrification work inside Pump house in NITK Surathkal

Amount

Supply of LT UG cable: Supplying of LT UG cable of following size having aluminium conductor PVC insulated sheathed galvanized, XLPE, steel wire / steel tape armoured cable with PVC outer sheathing 1.1KV class (conforming to IS 1554) Class 'A' PVC cables, HAVELLS/ UNISTAR/ GLOSTER / POLYCAB / UNIVERSAL / NICCO/ SBEE/ TORRENTO/ CCI - Tropadar make.

3.5 core x 95 sq.mm:

4.0 core x 16 sq.mm:

Digging trench: Digging a trench of 0.6M deep X 0.50M wide, refilling the trench to the required ground level and consolidation etc., complete. – CC cutting

Laying UG cable: Labour charges for laying of following size 1.1 kV class UG cable in existing trench, GI pole / stone ware pipe / on wall / structure/on pole as required.

95 Sq.mm to 120 Sq.mm (in existing trench)

16 Sq.mm ( on wall / structure)

Copper lugs: Supplying tinned copper lugs and crimping and wiring to terminal point for wire of following size. Make: Dowells / Braco / Ravi / Jainson

300 Sqmm Long barrel

150 Sqmm Long barrel

95 Sqmm Long barrel

50 Sqmm Long barrel

25 Sqmm Long barrel

Heavy duty cable glands: Supplying and fixing of following size heavy duty cable glands suitable for UG cable of 1.1KV class ( metal only ) - Make - Dowel, Mico, Glowstar

63 mm dia

45mm dia

32mm dia

Power board Panel – 16 SWG: Fabricating supplying and mounting MS box made out of 16 SWG suitable for floor / wall mounting, fully weatherproof with provision for better heat dissipation, provided with hinged front cover, equipped with tamperproof locking arrangements, with suitable size clamps with necessary cable entry with gland and box should be finished with 2 coats of red oxide primer paint and finally finished with approved colour enameled paint etc., complete.- Size - 60cm x 60cm

Moulded Case Circuit Breaker (MCCB): Supply and fixing following rating Moulded Case Circuit Breakers (MCCB) with spreader over the existing wood / panel board using necessary screws, bolts, nuts and wiring complete. protection of overload and short circuit with thermal magnetic/Micro processor release & Earth fault as per IS-13947 ( lcu =lcs ) Makes: L&T / ABB / Siemens/HPL/ LEGRAND/ MG make.

250A, 35kA, Four pole MCCB

100A, 25kA, Four pole MCCB

250A 3 Phase neutral bus bar: Supplying 250A ratede 3 phase with neutral bus bar using required capacity electrolytic aluminium strips covered with heat shrinkable coloured PVC sleeve, mounted on phenoloic / FRP/DMC insulator whic are mounted on powder coated 40x6mm MS flat frame work in existing panel board. The bus bar shall have suitable holes for termination of incoming and outgoing cables as per IS specification with necessary bolts, nuts and washers etc., complete.

250A 4 x 30x10mm Aluminium strips

CT: Supply, fixing and wiring 50/5 to 400/5 amps 5VA burden current transformer. Class 0.5 accuracy with tape wound

Digital meter with three line back light LCD type Display: Supplying of multi-function Digital meter with three line back light LCD type display for voltage, current, frequency, power , power factor ,KVA, KWH, KVAR suitable for three phase 4 wire, LT network with IP 54 degree of protection and completely wired as required with communication Port and class 0.5s accuracy. Make: Schnider, L&T, Meeco

MS angle iron frame work: Supply and fixing following size MS angle iron frame work for mounting panel board with bolt and nuts, painted with two coats of anti-corrosive enamel paint over two base coats of red-oxide priming coat

75x75x50x6mm –angle iron

GI Strip: Supplying and running of GI strips for grounding connections, using necessary fixing materials as required. 25x3mm GI strip

Chemical earthing: Chemical earthing for grounding, conduits, IC cut outs & other equipments on the meter board by using copper bonded/ SS rod with earth enhancing backfill compound which is non corrosive, thermally conductive, potential to permissible limits, superior fault conduction capacity, non toxic, weather resistance & capable of achieving ohmic value less than one ohm including concrete chamber and naming of earth pits. Using 4 ft copper bonded rod with backfill compound

Open PVC conduit wiring: Supplying heavy gauge PVC conduit pipe of following size confirming to IS 2509 with suitable size bends, junction boxes, adhesive paste and fixing using inverted wood plugs in case of RCC ceiling and RCC wall stone structure or rawl plugs in case of brick walls and cement plastering damaged portion using heavy gauge saddles at an interval of 700 mm using WF screws. White / black coloured as applicable. Make: VIP / Avonplast / Universal / Classic

40mm dia 2.5mm thick

25mm dia 2.5mm thick

20mm dia 2 mm thick

Point wiring using Copper wire with switch: Supplying and wiring adopting loop system in existing PVC Conduit /casing capping using copper PVC insulated multi strand FRLS 2x1.5 Sqmm copper wire confirming to the GTP with 6 Amps flush type SP control switch shall be fixed on the exising plastic sheet / gang box, the other end of the wires shall be terminated with sufficient loose length in a wood/PVC ,round block complete for each outlet.

Medium point above 3mtr upto 6mtr from tapping point to out let via switch

Long point above 6Mtr up to 10Mtr from tapping point to out let via switch

Wiring for Lighting circuit: Wiring for Lighting/ power circuit using 2 x 6.00 sq. mm. + 1 x 2.5 sq. mm. of PVC insulated 1100V grade multistrand FRLS copper conductor single core cable in open or concealed system of wiring.

Wiring for Lighting / UPS circuit: Wiring for Lighting/ power circuit using 2 x 2.50 sq. mm. + 1 x 1.5 sq. mm. of PVC insulated 1100V grade multistrand FRLS copper conductor single core cable in open or concealed system of wiring.

Teak wooden box: Supplying and flush mounting teak wooden box with front plate of hylum sheet of 3mm thick, made of not less than 12mm thick wood, after due groove cuttting, finishing with necessary cement plastering complete.

203x152x76mm (6" x 8"x 3")

254 x 178 x 76 mm ( 10" x 7" x3" )

Electrical accessories : Supplying and fixing of following size electrical accessories on existing switch board Group -A Make : anchor, GM, Elle, Cona

6 Amps lamp holder

16 Amps SP switch

16 Amps 3 way 5 pin socket

Electronic stepped regulator: Supplying and fixing of Electronic stepped regulator over existing wood board or flush mounting in plastic / nitches as per IS 1293 and IS 3854

Switch and socket: Supplying 6A flush type socket and 6 amps flush type SP switch either surface flush mounting in existing gang box or in 4mm thick sheet and fixing over a flush mounted wooden box and wiring using necessary capacity wires as required as per IS 1293 and IS 3654

6 Amps 3/5 Way

MCB Distribution board: 12 way SP & N double door DB: Supplying and fixing 12 way SP & N double door regular MCB distribution boards on wall / wood board / flush mounting using required clamps, bolts, nuts etc., with provision for fixing suitable type capacity MCB's single phase / 3 phase / single door with powder coated painting, naming of DB's etc., complete.( made out of 14 SWG MS enclosure)

miniature circuit breakers: Supplying and fixing following rating miniature circuit breakers on existing MCB distribution boards using necessary fixing materials and C type curve, indicator ON/OF, energy cross-3 with short-circuit breaking capacity of 10K and wiring complete as required. Make : Group A :- ABB / LEGRAND / L&T

5-32 Amps DP MCB

Fixing fittings: Fixing Department supplied LED Batten fittings indoor on the wall / ceiling / rafters / girders using 23/0.0076" twin twisted PVC insulated wires, required nos. of round blocks, clamps, necessary scaffolding, tools & labour complete.

GI Pipe bracket: Supply & fixing 32mm dia. class A GI pipe bracket up to 2.70 mtrs long terminated with a reducing collar of 40x25mm to which extra 175mm length is fixed bent at suitable angle and fixing to this bracket MV/SV/MH/FTL street light fittings of all capacities to GI or rail or RCC pole / wall using suitable clamps, bolts and nuts and wiring using capacity wires complete.

Fixing of street light/flood light: Fixing of Departmentally supplied street light/flood light fitting over existing pole/ wall ceiling including necessary scaffolding, clamps bolt nuts and wiring using suitable capacity wires

Wiring for Lighting / Power circuit: Wiring for power circuit using following PVC insulated 1100V grade multistrand FRLS copper conductor single core cable in open or concealed system of wiring. Make:Finolex,RR cable, polycab,v-guard

Shifting of existing Power panel: Dismantling the existing power panel from Power house -2 and and Shifting, installing, wiring and testing in pump house. Work includes necessary labour, tools & plants, transportation charges, welding works etc complete. Size of panel 160cm (L) x 40cm (w) x 150 cm (H)

Fixing of Ceiling fan: Fixing a ceiling / wall mounting fan of all capacities and all types with necessary clamps, angular, / to the existing S hook, with fan regulator, together with supplying and fixing a 5 ampere ceiling rose, necessary length of 23 / 0.0076” PVC insulated twin twisted copper wire and wiring complete.

M/s Anugraha power services

Shantha Electricals and Engineers Pvt Ltd