SPECIAL REPAIR TO BLOCK NO 53 AND 55 OF SF QTRS AT FAFA COLONY AT MORAR CANTT UNDER GE GWALIOR

Amount

Excavating over areas not exceeding 1.5 m deep and getting out in any type of soil complete all as specified and as directed.

Removing excavated material (soil) n exc. 50m and depositing where directed at a level not exc 1.5 m above the starting point complete all as specified and as directed.

M&L, moorum/red bajri filling in floors or pavings, laid in layers not exc 15 cm thick, spread, levelled and rammed including watering complete all as specified and as directed.

M&L hard core of (broken stone or boulders) guage n. exc 63 mm, deposited, spread & levelled in layers n. exc 15 cm thick watered and rammed to a true surface complete all as specified and directed.

M&L, roughening surfaces of old concrete roof by picking, sweeping clean and washing down with water to remove dust etc and applying a coat of cement slurry @ 3 Kg per Sqm complete all as specified and directed.

M&L for PCC (1:4:8) type D-2, (using 40 mm graded stone aggregate),75 mm thick, as in sub base for floor, finished even and rough complete all as specified and directed.

Demolition of cement concrete /brickwork of any description and in any position (unreinforced) in ground floors/ paving not exceeding 15 cm thick (below or above GL) complete all as specified and directed.

Dismantling floor, hearth or wall tiling,stone slabs,,coocking plateform slabs including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises complete all as specified and as directed.

M&L, 25mm thick PCC 1:2:4 type BO (using 12.5 mm graded BT stone aggregate) as in leveling course complete all as specified and directed .

M&L for non skid ceramic tiles, joint free, coloured tiles 7mm to 8 mm thick (Square or rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors etc set & jointed in neat cement slurry and pointed in white or coloured cement to match the colour of tile laid over and including 15 mm thick screed bed or bedding layer of cement mortar (1:6) complete all as specified and directed.

M&L for 75 mm thick cement concrete 1:3:6 type C-2 using 40 mm graded stone aggregate in plinth protection finished even and smooth without using extra cement including forming necessary joints 12 mm wide to the full depth of PCC at every 3 metres and every change of direction and filling the same with & including bitumen and sand 1:3 by weight of grade 'A' complete with and including necessary form work etc complete all as specified and as directed.

Taking down cement or cement lime plaster incl wall tiles, any description, on brick ,stone and concrete surface walls including chhajja of any floor and roof projection etc including raking out joints, hacking for key, scrubbing down with water etc complete all as specified and directed .

M&L 15 mm thick rendering in cement mortar 1: 6 on fair faces of brick work or concrete surfaces, finished fair and smooth complete all as specified and directed.

M&L rendering 15 mm thick in cement mortar 1: 4 on faces of brick work or concrete surfaces including chhajja's at any floor, parapet and projection of roof, mixed with WPC, finished fair and smooth complete all as specified and directed (WPC shall be measured and paid separately).

M&L, rendering 10 mm thick in cement mortar 1: 3 on fair faces of brick work or concrete surfaces as in ceiling, finished fair and smooth complete all as specified and directed.

M&L for ceramic tiles, joint free, coloured tiles 7mm to 8 mm mm thick as in skirting fixed over and including 10 mm thick cement screed in (1:4 ) CM set and jointed in neat cement slurry set and jointed in neat cement slurry and pointed in white or coloured cement to match with the colour of tiles complete all as specified and directed.with the colour of tiles complete all as specified and directed.

M&L for glazed ceramic tiles, coloured tiles, 200mm x 300mm x 7mm thick on vertical faces ie. as in skirting/dado etc set & jointed in neat cement slurry and pointed in white or coloured cement to match the colour of tiles fix over and including 10 mm thick backing coat in cement mortar (1:4) complete all as specified and directed.

M&L, applying two coats of distemper, oil emulsion white or tinted over and including a layer of birla or JK wall putty @ 1.20 Kg /Sqm including preparation of newly plastered surface complete all as specified and as directed.

M&L for complete removal of existing treatment on walls (any number of layers) by scrapping with steel scrapping or any other means, includind removing vegetable/plants root from walls/chajja's and applying two coats of distemper, oil emulsion white or tinted over and including a layer of Birla or JK wall putty @ 1.20 Kg / Sqm complete all as specified and as directed.

M&L applying two coats of cement base paint including preparation of newly plastered surface of walls complete all as specified and as directed.

M&L preparation of old plastered surfaces and applying two coats of white wash on walls and ceiling complete all as specified and as directed.

M&L applying two coats of synthetic enamel paint including preparation of new wooden surfaces of any description over 10 cm width or girth not other wise described, complete all as specified and as directed.

M&L applying two coats of synthetic enamel paint including preparation of old wooden surfaces of any description over 10 cm width or girth not other wise described, complete all as specified and as directed.

M&L preparation or new steel and iron surfaces of any description and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and directed.

M&L,old steel and iron surfaces of any description and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and directed.

M&L, preparation of newly plastered ceiling surface and applying three coats of white wash complete all as specified and directed.

Demolition of cement concrete(unreinforced)in Roofs,floors(other than ground floors), beams,stair cases,landing,chajja,s and similar suspended work complete all as specified and directed.

M&L, PCC 1:2:4 type B0 (using 12.5 mm graded stone aggregate) as in roof kerbs/coping/ bed block complete all as specified and directed.

Supply only integral water proofing compound(ISI marked) complete all as specified and directed.

Removing existing water proofing treatment (Brick tile terracing), roughning of concrete surfaces, cleaning of concrete surfaces with water and removing debries/rubbish off materials out side of Ministry of defence (MOD) land complete all as specified and directed

M&L, water proofing treatment with using APP Modified pollymeric membrane as per clause 11.43 of SSR 2009 and making good the surface for roof treatment by providing 10 mm thick cement plaster in CM (1:4) with WPC finshed even smooth complete all as direcred and after that roof treatment to be carried out as follows:- a) 1st coarse : one coat of bitumen primer @ 0.30 ltr / Sqm.(b) 2nd coarse : One coat of bonding material using blown type bituman confirming to IS - 702 of grade 85/25 @ 1.20 Kg/Sqm. (c) 3rd Coarse : A layer of APP modified polymeric membrane centre core of 100 micron HMH DPE, outer film 20 micron each thickness 2.00 mm having weight not less than 3.00 Kg/ Sqm.(d) 4th coarse : a coat of bonding material using blown type bituman confirming to IS - 702 of grade 85/25 @ 1.20 Kg/Sqm complete all as specified and directed. e) A topmost layer of surface finish with precast cement concrete tiles of size 250x250x25 mm conforming to IS 1237-1980 laid over 15mm th. scrreed bed in CM1:4 and joints filed with cement mortar 1:2 mixed .with water proofing compound as approved by GE complete all as specified and directed

M&Lin repair, vitreous china squatting pan, orissa pattern sise 580x440mm white with integral foot rest (excluding flushing cistern) including vitreous china ‘P’ or ‘S’ traps connection to trap and to flushing pipe to complete fixed in repairs and making good to floor complete all as specified and directed .

S&F, in repair PVC low level flushing cistern 10 litres capacity, white, with all fitting and fixtures including brackets and 32 mm bore PVC flush pipe, complete all as specified and directed.

S&F, in repair wash hand basin vitreous china (flat back) (550 x 400mm ) size including cutting for and pinning in ends of brackets and flush pipe complete all as specified and directed.

Supply only brass chromium plated waste fitting for wash basins and sinks with inlet and outlet, screwed for pipe or connections, and with one cleaning cap, 32mm bore complete all as specified and directed.

Supply only pillar taps 15mm dia cast copper alloy with capstan head chromium plated screwed down high pressure with or without lettered "Hot or Cold" complete all as specified and directed.

S&F in repair Swivel shower of chromium plated of size 65 to 90 mm for fixing with 15mm bore pipe complete all as specified and directed.

S&F PVC Grating Square 100 mm with hinge (openable) complete all as specified and directed .

Taking down eaves gutters and rain water pipes (any size 75mm to 110mm of any pattern) of any description and in any position, including all fittings, heads, shoes, bends, swan necks, etc (measured overall as fixed along the centre line over fittings and accessories) complete all as specified.

S&F,110mm bore PVC (SWR) pipes, single socketed, in any length with rubber ring joints, fixed to walls, complete all as specified and directed.

S&F, 75 mm bore PVC (SWR) pipes, single socketed, in any length with rubber ring joints, fixed to walls, complete all as specified and directed.

S&F,110 mm bore PVC (SWR) pipes, single socketed, in any length with rubber ring joints, laid in trenches or in floors, complete all as specified and directed.

S&F,75 mm bore PVC (SWR) pipes, single socketed, in any length with rubber ring joints, laid in trenches or in floors, complete all as specified and directed.

S&F,110mm bore PVC (SWR) branch pieces, single (single Y) equal or unequal, provided with access door, complete all as specified and directed.

S&F,75 mm bore PVC (SWR) branch pieces, single (single Y) equal or unequal, provided with access door,complete all as specified and directed.

S&F, 110mm bore PVC (SWR) junction single (single T), equal or unequal, provided with access door complete all as specified and directed.

S&F 75 mm bore PVC (SWR) junction single (single T), equal or unequal, provided with access door complete all as specified and directed.

S&F 110 mm bore PVC (SWR) vent cowl, complete all as specified and directed.

S&F in repair 20mm bore ball vavle high pressure of PTMT with epoxy coated aluminium rod and high density plastic ball screwed for iron pipe and fixed complete all as specified and directed.

S&F in repair 20 mm bore gun metal globe / gate valve with iron wheel head screwed both ends for iron pipe complete all as specified and directed.

Taking up and down 15 mm bore steel tubing and connections including cleaning for refixing or to store complete all as specified and directed.

Taking up and down 20 mm bore steel tubing and connections including cleaning for refixing or to store complete all as specified and directed.

M&L cutting chases in brick walls, pinning in, making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, shelves, lintels, etc, and cutting chases for concealed water tubings or conduit wiring, etc complete all as specified and directed.

S&F 15 mm bore tube medium grade galvanized with all fitting and fixed complete to walls and ceiling or laid in floor complete all as specified and directed.

S&F 20 mm bore tube medium grade galvanized with all fitting and fixed complete to walls and ceiling or laid in floor complete all as specified and directed.

Refixing old 15 mm bore steel tubing and connections in new or old positions (walls, ceiling, floor etc) complete all as specified and directed.

Refixing old 20 mm bore steel tubing and connections in new or old positions (walls, ceiling, floor etc) complete all as specified and directed.

S&F rotation moulded polyethylene water storage tank capacity 500ltr (cylindrical vertical with closed top ) double layer construction , ISI marked , hoisted and fixed in position including dismantling of old tank and removing to from site complete all as specified and directed.

S&F, in repair 15mm dia brass bib cock, cast copper alloy with butterfly handle, screwed down screwed for iron pipe or for brass ferule complete all as specified and directed.

S&F in repairs PVC conections 15mm dia for wash hand basin and low level flushing cistern of 450 mm length PTMT nuts at ends to connect pipe or sanitary fitting complete all as specified and directed.

S&F, in repair.15 mm bore stop valve cast copper alloy screwed down high pressure with CAPSTAN HEAD handle chromium plated concealed type screwed both ends for iron pipe or for unions and fixed

S&F in repair 15 mm bore stop valve cast copper alloy screwed down high pressure with capstan head, handle chromium plated angular type screwed both ends for iron pipe or for unions and fixed complete all as specified and directed.

S&F, in repair LDPE pipes of pressure rating 6Kgf/Cm Square fixed complete incl all fittings to wall and ceilings or in floors of 32 mm bore complete all as specified and directed.

Taking down ventilators of any type not exc 1 Sqm each complete all as specified and as directed.

S&F steel ventilator with top hung shutter including hinges, steel peg stay complete all as specified and as directed.

Supply only 3mm thick figured glass pin head type in square n.exc 0.5 Sqm in each pane new ventilator / window shutter complete all as specified and directed.

Taking down chowkat with shutter (without taking off shutters from the frame) not exc 1.5 Sqm each complete all as specified and as directed.

S&F Box type steel windows with side hung shutters (double shutters for glass and gauze) jointed together with and including grills using 12mm square bars @ 10cm C/C as per TD No CEBZ/TD/14/2011 including box type hinges with steel handle and steel peg stay complete with glazing bars dovetailed and welded complete all as specified and as directed. Note:- Glass/gauge shall be measured and paid separately under respective item as suply and fix complete all as specified and as directed by the Engineer-in-Charge..

S&F Factory made solid PVC door frame of size 50 mm x 47 mm made out of 5 mm plain colour PVC sheet reinforced with MS square tube with wooden grain printed PVC sheet used inserted of plain colour PVC sheet & edges will be painted to match with printed sheet complete all as specified and as directed.

S&F Factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of MS tubes for top & bottom rails. MS frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20 mm width struck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail. Panelling of plain colour PVC sheet to be fitted in the MS fram welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement complete all as specified and directed

Taking down chowkat with shutter (without taking off shutters from the frame) exc 1.5 Sqm but n exc 4.0 sqm each complete all as specified and as directed.

Taking down shutters of any description exc 1 sqm and n exc 2 sqm each complete all as specified and directed.

S&F 35mm thick factory made, IInd class hard wood, plain framed, paneled shutter with lock rail and panel of 8mm BWP commercial ply or 12 mm veneered particle board with commercial veneering on both faces. The size of rail and stile as [per IS : 1003 (Part-I), kiln seasoned and chemically pressure treated complete all as specified and directed.

S&F 35 mm thick factory made 2nd class hard wood glazed and skeleton shutters, open repeated and prepared to receive glass, gauze etc (with sash bars) edges of framing plain, chamfered or rounded, fitted with cut and mitered beads for securing glass etc, size of member of shutter as per specified in SSR part-I section 8,clause 8.24(a) and for door and fixed with chowkats, complete all as specified and directed.

S & F Butt hinges, medium weight, cold rolled mild steel, 100 mm size complete all as specified and directed

S&F 150mm long anodised aluminium handles, cast type complete all as specified and as directed.

S&F 200 mm long mild steel barrel tower bolt stove enameled black with bright bolt each complete all as specified and as directed

S&F 150 mm size mild steel pressed handle, oval type stove enameled black complete all as specified and directed.

S&F 250 mm long mild steel sliding door bolts plate type stove enameled black with bright bolt not less than 12 mm dia with and including a minimum of 6 mm bolts and nuts four on bolt plate and two on stalle plate complete all as specified and as directed

S&F 300 mm size, rat tail type door spring of mild steel including roller and roller plate complete all as specified and directed.

S&F mild steel hold fast, clamps or similar small articles (conforming to Fe-410-0) complete all as specified and directed.

S&F 3 mm thick sheet glass ordinary quality and glazing with oil putty in square n.exc 0.5 Sqm in each pane complete all as specified and as directed.

S&F galvanised mild steel wire cloth, 0.46 mm nominal dia of wire and average width of aperture 1.18mm complete all as specified and as directed.

Demolition of brick work or stone/ boulder masonry built in cement mortar or cement lime mortar including removal to rubbish complete all as specified and as directed.

M&L brick work with sub class ‘B’ bricks straight or curved on plan exc 6 mtr mean radius built in CM 1:6 complete all as specified and as directed

M&L for applying treatment on exposed roof portion incl beams, chajjas, slab etc as under:- (a) Removing all loose concrete elements & applying acid wash & applying cement slurry mixed with Nitobond / tapcrete all as specified and directed. (b) Inserting drilling holes in the wall /beam by 10 mm dia bars & tuck welding with existing reinforcement @ 0.50 m c/c, nailing wire fabric 50 x 50 mm in the complete area all as specified and directed. (c) M&L 15mm dubbing coat in CM (1:2) mortar mixed with Nitobond /Tapcrete @ 2 % by weight all as specified and directed.

M&L fixing of precast RCC bond stone 50mm thick in brick /stone walls complete all as specified and directed. Note : Reinforcement shall be measaured and paid in separate item.

M&L for TMT bars 10 mm dia and over as in reinforcement, cut to length, bent to shape required including cranking, bending spirally for hoping for columns, hooking ends and binding with and including MS wire (annealed) not less than 0.9 mm dia complete all as specified and directed.

All as per item No 88 above but 5 mm to 8mm dia as in stirrups, spacers and binders etc omplete all as specified and directed.

S&F in repair sink with drainage board made of stainless steel 1mm thick kitchen or laboratory with plug washer and waste coupling including bedding in CM to dwarf wall or including fixing cantilever brackets and connections to pipe over all size 915mmx460mm built size 410mmx330x160mm omplete all as specified and directed.

S&F Brass, Chromium plated Tubular towel rail, 20 mm dia ,'D' type , 60 cm long between flanges of approved make complete all as specified.

S&F in repairs of stainless steel plate rack for utensils of size 750 X 750 mm & standard quality complete all as specified and directed

S&F chicken wiremess with tack screws of galvanised mild steel wire cloth of 0.56mm nominal dia of wire and average width of aperture 1.18mm complete all as specified and directed

M&L for Harrison rails, powder coated aluminum alloy of 25mm dia pipe decorative finish with and including supply and fixing powder coated decorated type brackets, stops, rollers etc. fixed on walls with brass screws with PVC rawl plugs as in curtain rods fixed in repair complete all as specified and directed.

Dismantiling of stone slabs and tiles (Kota stone etc.) of any discription or any thickness in floors, aprons, skirting, dado etc. laid bedded and pointed in any mortar complete all as specified and directed.

M&L for machine cut Kota stone slab 20 mm to 25 mm thick , as in flooring , laid over cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and including screed bed or bedding layer of mortar 15 mm thick in cement mortar (1:6 ) complete all as specified and directed.

M&L for mirror polish to existing kota stone floor complte all as specified and directed by enginner in charge.

M&L for machine cut kota stone slab 20-25 mm thick as in riser / steps, skirting, dado and pillars laid and jointed with grey cement slurry mixed with pigment to match with the shade of the slab including rubbing and polishing over and including 10 mm thick backing coat in CM (1:4) complete all as specified and directed.

S&F soap dish, vitreous china white, approximate size 160x 160 x 90 complete all as specified and directed.

M&L 15mm thick grainte slab of any shade as approved by GE as in kitchen platform bedded and joined with grey cement slurry and joined with white cement with admixure of pgiment to match the shade of granite stone including complete all as specified and directed

S&F 2nd class HW plain, solid straight chowkat and frames wrought, framed rebated on the solid, rounded or chamfered put together with glue pinned at joints complete all as specified and directed

M&L, 60 mm thickness machine pressed precast concrete Inter locking paver block M-35, any shape and size conforming to IS 15658-2006 in grey cement glossy finish rubber mould casted laid dry over sand cushioning complete all as specified and directed.

M&L sand filling under floores or in foundation including watering and consolidation complete all as specified and directed

Dismantling boarding any description fixed with nails in any position (including cup board shutter/shelve upto 25mm thick) complete all as specified and directed

M & L for 18 to 19 mm thick prelaminated particle boards in shutter and shelves for cup boards including alround 5-6mm thick lipping (!st class hard wood lipping) complete all as specified and directed.

S&F 25mm thick block board of grade 2 quality and glazing with oil putty in squares n exc 0.5 sqm in each pane complete all as specified and directed

S&F in repairs PVC waste pipe flexible type 32mm bore complete all as specified and directed

S&F magic door eye stainless steel complete all as specified and directed

M&L prepration of new surfaces of walls and applying one coat of weather proof water based emulsion paint (Acrylic paint exterior grade) in isolated width n.exc 30 cm wide complete all as specified and directed.

Taking down carefully existing aluminium/copper point wiring (light, fan,socket or power point) complete of any description including fitting such as switches, ceiling roses, pendants, tube light fitting, ceiling fan with regulator, sockets, wooden boards, laminated sheets from sunken boxes boards, shades light fitting etc and making good the disturbed surfaces of walls, floors, ceiling etc to match with existing surfaces complete all as specified and directed.

Point wiring with PVC insulated 1.5 sqmm multi stranded FRLS copper conductor cable 1100 volts grade drawn into and including concealed rigid nonmetallic PVC conduit medium grade not less than 20 mm (ISI marked) with all conduit fitting and fixing accessories including sunk in cast iron/pressed steel terminal boxes (duly painted with two coats of anti corrosive paint out side and two coats of aluminium paint inside) with 2.8 mm thick HYLAM brand laminated white bakelite sheet cover for mounting switches, sockets, fan regulators, etc and 1.5 sqmm multi strand copper conductor cable as continuous earthwire for the following complete all as specified and directed :- Make of Conduit :- Sri Nath pipes/Anchor/Polycab. Make of wire :- Finolex/Havells/Polycab.

One light/fan point controlled by one switch complete all as specified and directed

One bell/buzzer point controlled by one switch complete all as specified and directed

Two way point controlled by two Nos two switch complete all as specified and directed

One 5 pin socket outlet 5 Amps controlled with one switch on the same board.

One 5 pin socket outlet 5 Amp controlled by one switch on independent board complete all as specified and directed

All as per item No 112 but with 2.5 sqmm multistrand copper conductor cable for one 15 Amp socket outlet controlled by one switch on independent board and 1.5 sqmm PVC insulated multi strand copper conductor cable as continous earth wire complete all as specified and directed Make of Conduit : Sri Nath pipes/Anchor/Polycab. Make of wire : Finolex/Havells/Polycab.

S&F Switch piano flush button single pole one way 5 Amp complete all as specified and directed. Make : Cona,Leader,Anchor

S & F switch piano flush button single pole two way 5 amp complete all as specified and directed. Make : Havells / Leader / Cona.

S&F Switch socket outlet, 5 Pin, 6 Amp 2 in 1, flush type, universal complete all as specified and directed. Make : Havells / Leader / Cona.

S&F Switch socket combination , 5 Pin, 6 Amp 2 in 1, flush type, universal complete all as specified and directed. Make : Havells / Leader / Cona.

S&F Switch socket combination, 6 Pin, 5/ 16 Amp 5 in 1, flush type, universal complete all as specified and directed. Make : Havells / Leader / Cona.

S&F Ceiling rose 3 terminal/pvc/polycarbonate, isolated body complete all as specified and directed Make : Havells / Leader / Cona.

S&F Fan regulator stepped type electronic fan regulator flush type on the existing phenolic laminated sheet etc complete all as specified and directed Make : Havells / Leader / Cona.

S&F Buzzer Ding Dong AC,230 volts single pole flush type on the existing for battern fittings complete all as specified and directed Make : Havells / Leader / Cona.

S&F bell push 5 Amp complete all as specified and directed Make : Havells / Leader / Cona.

S&F angular Lamp holder including 9W/12W, PVC/polycarbonate type with back plate suitable for angular fittings complete all as specified and directed Make of Lamp Holder :- Anchor, Leader, Cona Make of LED Bulbs :- Philips, Crompton, Wipro.

S&F Ultra bright LED Tubelight fitting of LED 18/22 w incluing reqd length of 1.5 Sqmm PVC multistranded copper conductor ro electrical connection from ceiling rose to connector of LED fitting including testing on completion all as specified and directed. Make : Halonix/Wipro/Havells.

Supply, install, commissioning and installation of distribution meter box indoor type, factory made out of CRCA sheet 2mm thick with angle iron 30x30x2 mm complete with inside, outside powder coated independed housing for meters with transperent glass & rubber gasket packing with suitable size copper single/ two core wire for each control, cable gland, with 200 Amp rated TPN aluminium busbar (for outgoing) duly insulated (including self insulated) maintaining proper space for each busbar and grouting panel in wall etc and making good the disturbed surface complete including with arrangement and including taking down the existing metal/PVC box comprising for following fittings complete all as specified and directed :- (i) MCCB TPN, 63 Amps, 16 KA - 01 No (For incoming). Make :- Schneider/Legrand / Havells. (ii) Amp Meter (0-100 Amp) - 01 Nos (iii) Volts Meter (0-500 Volts ) - 01 No (iv) Indicator Lamp set of three R,Y,B - 01 Set (v) ASS & VSS with CTs - 02 Nos ( 01 Each) (vi) MCB SP 40 Amps, 230 volts - 04 Nos (For outgoing). Make : Schneider, Legrand, Havells (vii) Nutral bus bar link mounted on insulator. (viii) Place for fixing the energy meter - 04 Nos Note :- Taking down and refixing of the electric meters is deemed to included in the quoted rate.

Sheet metal enclosure MCB DB, double door , 08 way SPN, 240 volts with 200 Amps rated bus bar with blanking plates wherever required and I.P. 20 degree protection complete all as specified and directed Make of MCB & MCB DBs : Schneider / C&S / Legrand

S&F MCB single pole and neutral 240 volts, 25 to 40 Amps complete all as specified and directed Make of MCB & MCB DBs : Schneider / C&S / Legrand

S&F MCB single pole 240 volts, 6 to 32 Amps complete all as specified and directed Make of MCB & MCB DBs : Schneider / C&S / Legrand

Taking down submain wiring of any size any type and in any position metalic/non metallic PVC conduit of wooden batten complete all as specified and directed.

M&L for sub main wiring with 2 runx 6 Sqmm + 4 sqmm earth wire single core PVC insulated cable unseathed multistranded copper conductor LT 1100 volts grade FRLS cable IS-694 (ISI marked with valid CML No ) drawn in & icluding PVC conduit of dia not less than 25mm in concealed (ISI marked with valide CML No ) including its all fittings/accessoreis with one run single core copper cable 4 sqmm multistranded conductor (ISI marked with valide CML No) colour code as a earth continuity and connecting upto DB with suitable lugs all as specifed and directed. Make of Conduit & wire : Anchor / Finolex / Polycab.

S&F Earthing complete with galvanised steel earthplate electrode 60 cm x 60 cm x 6 mm thick burried directly in ground (earth pit not less than 2.25 metres deep below normal ground level) with top edge of plate not less than 1.5 metre below normal ground level connected to galvanised earth lead wire 4 mm dia by means of bolts, nuts, check nuts and washers of galvanised iron or steel all as shown in electrical plate No 5 of MES Schedule Part-I connecting to earthing point and testing on completion with and including 15 mm bore light grade G.I. protection pipe (0.5 metre beyond pit to main switch), PCC pit in mix 1:3:6 type C1 with RCC 1:2:4 type B-1 40 mm thick cover reinforced with 6 mm dia M.S bars 3 Nos both ways with lifting hook made out of 6 mm dia bar, watering arrangement with funnel and wire mesh and 20 mm bore light grade G.I. watering pipe, common salt and charcoal filling, necessary excavation and earth work complete all as specified and directed

M&L for taking down fan, sealing cable and refixing the same all as specified and directed.

Supplying, laying, testing and commissioning of XLPE insulated screened PVC bedded galvanised steel strip or wire armoured electric power cable (Heavy duty ) with aluminium conductor 1100 volts grade, cross sectional area size 25 Sqmm 4 Core complete all as specified and directed. Make of cable : Finolex / Polycab / Gloster.

Excavation in trenches n exc. 1.5 m wide and n' exc. 1.5 m in depth and getting out in soft/loose soil complete all as specified and directed.

Returning, filling of excavated soil, including spreading leveling, watering and well ramming in layers not exceeding 25cm complete all as specified and directed.

Removing of surplus soil to a distance n exc 50 m and depositing where directed at a level n exc 1.5m above the starting point complete all as specified and directed

Sand filling in trenches with clean dry unwashed sand free from sharp particles, gently punning around the cables complete all as specified and directed

Bricks, old size sub class `B' laid in trenches with width wise along the alignment of the cable as protection complete all as specified and directed

S&F tube 'Light' grade galvanised with all fitting laid in trenches fixed to wall and floor of 50 mm dia for cable protection complete all as specified and directed.

S & F security light fittings better optics for uniform distribution IP 65 protection LED of 20 watt, Heat resistance glass, pressure die cast aluminium housing including 25mm dia galvanised iron pipe light grade bracket bent to shape over all length 0.60mtr fixed to wall with 02 Nos FI clamps made of 40 x 6 mm FI, 15 cm long, 8 mm dia bolts and nuts with washers grouted in wall complete including reqd length of 1.5 Sqmm PVC multistranded copper conductor for connection from ceiling rose to light fittings incl testing on completion complete all as specified and directed. Make :- Havells, Wipro, Philips.

M/s Himgiri construction

M/s Ratan Lal Jain and Co.

Babatia super works

mahamaya constructions