NIT 57 OF 2020-21 SPECIAL REPAIR TO BUILDING NO T-19 (COOK HOUSE AND DINING HALL) AT BANIHAL, BUILDING NO T-89 (TSTS TOILETS), BUILDING NO P-14 AND T-4 AT RAMBAN AND PROVN OF 02 GEYSERS AT PATNITOP UNDER GE (I) 873 EWS

Amount

B/R Portion

Taking down chowkhats with shutters (without taking off shutter from the frames) not exceeding 1.50 Sqm each, including cutting holes for taking out hold fasts or dismantling brick work and making good the disturbed surface complete all as specified and directed.

Taking down chowkhats with shutters (without taking off shutters from the frames exceeding 1.50 Sqm and not exceeding 4.00 Sqm each, including cutting holes for taking out hold fasts or dismantling brick work and making good the disturbed surface complete all as specified and as directed.

Aluminium powder coated three track sliding window comprising of one set of fly proof shutter and two set of glazed shutter with frame of size 92mm x 31.75mm x 1.5mm and shutter frame of size 40mm x 18mm x 1.55mm with necessary joining cleats, glazing clips, rubber gasket, anodised aluminium snap beading and connected locking arrangement, complete all as specified. Notes : 1. Glass filling in panels of window and aluminium wire mesh / wire cloth shall be deemed to be included in the quoted rates of item. 2. Aluminium alloy wire cloth in panels of wire gazed shutter shall be 0.45 mm nominal dia of wire and average width of aperture 1.40mm fixed with aluminium wire staples. 3. Glass filling in panels of glazed shutter shall be 5mm thick tinted sheet glass of approved make and shade / tint.

Steel windows with side hung shutter including projecting type hinges, steel handle 02 Nos., steel tower bolts 100mm long and steel peg stays lugs including hold fast complete with glazing bars dovetailed or welded including locking arrangement and one shop coat of red oxide primer complete all as specified and as directed.

4mm thick sheet glass ordinary quality and glazing with oil putty / screws, in square not exceeding 0.5 Sqm in each pane complete all as specified and as directed.

Preparation of new steel surfaces of any description, over 10cm width or girth and applying two coats of synthetic enamel paint, complete all as specified and as directed.

Pressed steel frame of size 125mm x 60mm for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate etc., complete all as specified and directed.

35mm thick Flush shutters, solid core construction, with block board core and plywood face panels, commercial type on both sides, complete as specified and directed.

35mm thick, 2nd Class hard wood, factory made, glazed and skeleton shutters open rebated and prepared to receive glass, gauze, etc. (without sash bars), edges of framing plain, chamfered or rounded fitted with cut and mitred beads for securing glass, etc.; sizes of members of shutters as specified in SSR Part I, Section 8, clause 8.24 (a); supplied and fitted to chowkhats, complete all as specified and as directed.

PCC 1:2:4 type B0 (using 12.5mm graded crushed stone aggregate) as in in bed block for holdfast and similar works etc. complete all as specified and directed.

Mild steel works as in clamps, hold fasts and similar small articles conforming to Fe-290 Gde-E-165, complete all as specified & directed.

Stainless steel wire cloth 0.36 mm nominal dia of wire and aperture 1.40mm and fixed with tinned tacks or galvanized wire staple all as specified and directed at site

Butt hinges, medium weight, cold rolled mild steel, 100mm size, complete all as specified and directed.

Mild steel barrel tower bolt, stove enamelled black with bright bolts and fixed complete of Size 150mm long complete all as specified and directed.

Mild steel pressed handle, oval type, stove enamelled black of size 150mm complete all as specified and directed.

Mild steel, sliding door bolt plate type, 300mm, stove enamelled black, with bright bolt not less than 12mm dia with and including a minimum of 6 bolts and nuts, four on bolt plate and two on staple plate and fixed, complete all as specified and directed.

Mild steel, Ordinary rat tail rod pattern springs including roller and roller plate, 300mm, and fixed, complete all as specified and directed.

Preparation of new wooden surfaces of any description, over 10cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer, complete all as specified and as directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises, complete all as specified and as directed.

Demolition of stone slabs and tiles of any description or thickness in floors, aprons etc. and removing rubbish off the premises, complete all as specified and as directed.

20mm to 25mm thick of size not less than 53 x 53cm, machine cut Kota stone slab flooring laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and mirror finish polishing, over and including 15mm thick screed bed or bedding layer of cement mortar 1:3 all as specified and as directed.

18mm to 20mm thick, machine cut Kota stone as in riser or steps, skirting, dado and pillars laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and rounding off edges complete with mirror finish polishing, over and including 10mm thick backing coat of cement mortar 1:3 all as specified and as directed.

Makrana white marble tiles 30cm x 20cm x 20mm thick machine cut, bedded jointed and pointed with grey cement slurry including cutting and polishing types over and including 15mm thick screed bed in cement mortar 1:3, complete all as specified and directed.

Glazed ceramic coloured wall tiles in any type and in any pattern in vertical surfaces of size 300mm x 200mm x 7mm thick set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 10mm thick backing coat in CM 1:4, finished fair to received the tile, complete all as specified and directed.

Vitrified coloured tiles, light shade, of 10mm thick (square/ rectangular) polished, area of each tiles exceeding 0.36 sqm but not exceeding 0.42 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15mm thick screed bed in CM 1:4 and pointed in coloured cement to match the colour of tile all as specified and directed.

75 mm thick Cement concrete type D-2, 1:4:8 (using 40 mm graded crushed stone aggregate) in sub base, complete all as specified and directed.

Chequered cement concrete tiles 20cm x 20cm x 25mm thick, set, jointed and pointed in neat cement slurry with grey cement and pigment as in floors including over 15mm screed bed in CM 1:3, complete all as specified & directed.

Chequered cement concrete tiles 30cm x 30cm x 25mm thick, set, jointed and pointed in neat cement slurry with grey cement and pigment as in floors including over 15mm screed bed in CM 1:3, complete all as specified & directed.

Demolition of brick work or stone/ boulder masonry built in cement mortar including all quoins, pillars etc. but excluding ashlars facing, dressed stone work and precast concrete articles complete all as specified and as directed.

Brick work with sub class ‘B’ bricks, straight or curved on plan exceeding 6m mean radius built in in CM 1:6, complete all as specified and directed.

Brick work (except bricks) with sub class ‘B’ bricks, straight or curved on plan exceeding 6m mean radius built in in CM 1:6, complete all as specified and directed.

Brick work with sub class ‘B’ bricks (old size), straight or curved on plan to any radius, in half brick thick wall built in cement mortar 1:4, complete all as specified & directed.

Walling of random rubble stone masonry, well bonded, bedded and solidly hearted built in cement mortar 1:6, brought up to courses, complete all as specified and directed. Note : Volume of PCC bond stone provided in lieu of Stone bond stone under Serial item No. 35 here-in-after shall be deducted from total cumulative quantity of stone masonry.

Walling of random rubble stone masonry (Except stone), well bonded, bedded and solidly hearted built in cement mortar 1:6, brought up to courses, complete all as specified and directed. Note : Volume of PCC bond stone provided in lieu of Stone bond stone under Serial item No. 35 here-in-after shall be deducted from total cumulative quantity of stone masonry.

Precast cement concrete, type C-1 1:3:6 (using 20mm graded crushed stone aggregates) as in bond stone set in cement mortar 1:6 and finishing exposed surfaces including necessary form work, complete all as specified and as directed.

Extra over stone walling for hammer dressing to face stones and dressing of face beds and joints, as specified, of random rubble walling, uncoursed or brought up to courses with maximum depression on face from straight edge held against the dressed surface not exceeding 40mm, complete all as specified and as directed.

Taking down cement plaster on bricks or stone wall/ceiling decayed surfaces of concrete from roof projection or RCC chajjas etc. including racking out joints, hacking for key, scrubbing down with water etc., complete all as specified and directed.

Rendering 15mm thick in cement mortar 1:6 on fair faces of brick work or concrete surfaces, finished even and smooth without using extra cement, complete all as specified.

Rendering 15mm thick in two layers, 5mm thick using WPC @ 3% by weight of cement over 10mm thick on fair faces of brick work or concrete surfaces in cement mortar 1:4 , finished even and smooth without using extra cement, complete all as specified. Note :- WPC shall be measured and paid separately.

Rendering 05mm thick in cement mortar 1:4 on fair faces of brick work or concrete surfaces in ceiling, finished even and smooth without using extra cement, complete all as specified.

Preparation new plastered surfaces of wall and applying two coats of oil emulsion distemper roller finish over a coat of alkali resistant primer coat over complete all as specified and as directed.

Preparation new plastered surfaces of walls and applying two coats of cement base paint including one coat of cement primer complete all as specified and directed.

Preparation old plastered / unplastered surfaces of walls and applying one coat of cement base paint, complete all as specified and directed.

Preparation new plastered or previously untreated surfaces of ceiling and applying three coats of white wash , complete all as specified and directed.

Preparation old plastered surfaces of ceiling and applying two coats of white wash , complete all as specified and directed.

Dismantling wall and ceiling board (fibre, pulp, PVC, insulation etc.) or insulation boards / slabs / blankets, any thickness including cover fillets complete all as specified and as directed.

4 mm thick non asbestos designer E-boards classic laid in and including false ceiling of aluminium snap grid work 60 x 60 cm with using 36.5mm x 23.5 mm x 1.5 mm thick main tee, 23.5 x 23.5mm x 1.28 mm cross tee and 25x25x1.5mm angles fixed to perimeter of wall including necessary supporting hanger with 3 mm dia GI wire and J bolts washer nuts for securing frame work to ceiling suspended @ 120 cm c/c both ways, complete all as specified and as directed.

Dismantling plain or corrugated steel sheeting any gauge, thickness including nanital or similar pattern from roof covering or in ridges, hips, valley gutter and similar works complete, all as specified and directed.

Pre-painted galvalume aluminium zinc coating G.I based corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550 MPA as in roof covering/wall cladding, fixed with self taping screws, complete all as specified and directed.

Pre-painted galvalume aluminium zinc coating G.I based plain steel sheet 0.50mm thick of any colour having tensile strength of 550 MPA as in roof covering / cladding to wall, fixed with self taping screws, complete all as specified and directed.

Dismantling wrought iron or mild steel work of any description not otherwise specifically provided for, complete all as specified and as directed.

Mild steel rolled work as in roof trusses (framed), trussed, purlins, crane gantries, rails and fastening and heavy bracket framing (beam, tee, angle, square / rectangle sections, channel or flat section) including distance pieces, cleats etc. confirming to grade FE 410-0 complete all as specified and directed.

Solid PVC door frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with MS square tube, supplied and fitted in openings as per specification and drawing shown in SSR Part-II, complete all as specified and as directed.

Factory made solid panel PVC door / cup board shutter 30mm thick (style) consisting of frame made out of M.S tubes for top & bottom rails M.S frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement or stiles and plain colour PVC sheets for top rail, lock rail and bottom rail on either side and as gap insert for top rail and bottom rail. Panelling of plain colour PVC sheet to be fitted in the M.S frame welded/sealed to the stiles and rails with suitable PVC sheet beading and joined together with solvent cement, supplying and fixing in the frame at site as per specification in SSR Part-I.

Steel ventilator with top hung shutter including hinges, steel peg stay, complete including one shop coat of red oxide primer complete all as specified and as directed.

4mm thick figured glass, pin head type and glazing with oil putty or wooden beads in square not exceeding 0.5 Sqm each complete all as specified and directed.

Aluminium anodized barrel tower bolt of extruded section and fixed complete of Size 150mm long complete all as specified and directed.

Aluminium handle cast type anodized of size 150mm complete all as specified and directed.

Aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) 250mm, and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed, complete all as specified and directed.

Dismantling PVC water tanks exceeding 500 ltr capacity but not exceeding 1000ltrs, complete all as specified and directed.

Rotational moulded polyethylene water storage tanks triple layer (cylindrical vertical with closed threaded top) of colour other than black, hoisted and fixed in position, including over flow and drain out pipe complete of 1000 litre capacity complete all as specified and directed.

Ball valves high pressure of PTMT with epoxy coated Aluminium rod & high-density plastic ball screwed for iron pipe and fixed to 20mm bore dia of pipe (Minimum weight 210gms), complete all as specified and directed.

Taking up or down 15mm bore steel tubing and connection including cleaning for re-fixing or removal to store complete all as specified and as directed.

Steel water tubing medium grade galvanised with all fittings including short lengths, fixed to walls, concealed in wall and ceiling or laid in floor complete with all fittings (such as bends, elbows, Tee, short pieces, connectors, back nuts, diminishing pieces, caps and plugs, unions etc.) of nominal bore dia 15mm, complete all as specified and as directed.

Taking up or down 20mm bore steel tubing and connection including cleaning for re-fixing or removal to store complete all as specified and as directed.

Steel water tubing medium grade galvanised with all fittings including short lengths, fixed to walls, concealed in wall and ceiling or laid in floor complete with all fittings (such as bends, elbows, Tee, short pieces, connectors, back nuts, diminishing pieces, caps and plugs, unions etc.) of nominal bore dia 20mm, complete all as specified and as directed.

Bib tap with wall flange cast copper alloy CP, fancy type, with capstan Head handle, screwed down, screwed for 15mm bore iron pipe or for brass ferrule, complete all as specified and directed.

Stop cock / Angle valve with adjustable wall flange CP cast copper alloy, fancy type, with capstan head handle and adjustable wall flange, screwed down, high pressure screwed both ends for 15mm bore iron pipe or for unions, complete all as specified and directed.

PVC connection 45cm long fitted with PTMT nut and washer on both ends, fixed to 15mm bore iron pipes, complete all as specified and directed.

Vitreous china Orissa pan of pattern, long pan size 580mm x 440mm, with ‘P’ or ‘S’ trap, front or back inlet and integral foot rest complete including lime concrete bedding and connection to drain or outgoing pipe and to flushing pipe, and anti siphon pipe, complete all as specified and directed.

10 litres capacity PVC low level flushing cistern of approved make complete with PVC flush pipe and connection to water closet, fixed in repair, complete all as specified and directed.

Demolition of cement concrete in ground floors and paving (un-reinforced) not exceeding 15cm. thickness, below or above ground level, complete and removing rubbish from the site, complete all as specified and directed.

75 mm thick Cement concrete type C-2, 1:3:6 (using 40 mm graded crushed stone aggregate) in sub base, complete all as specified and directed.

50 mm thick Cement concrete type B-1, 1:2:4 (using 20 mm graded crushed stone aggregate) in sub base, complete all as specified and directed.

Non-skid coloured glazed ceramic tiles of any shade and any pattern of size (Pattern consists combination of two or more tiles) 400mm x 400mm x 7mm thick, over and including 15mm thick screed bed in CM 1:4 as in floors etc. jointed in neat cement slurry and pointed in coloured cement to match coloured tiles, complete all as specified and directed.

Rendering 10mm thick in cement mortar 1:6 on other than fair faces of brick work or on one side of lathing, finished even and smooth without using extra cement, complete all as specified.

Supply only integral water proofing compound all as specified and as directed.

Preparation of new steel surfaces of any description, over 10cm width or girth and applying two coats of synthetic enamel paint, over a coat of red oxide primer, complete all as specified and as directed.

Preparation of old steel surfaces of any description, over 10cm width or girth and applying one coat of synthetic enamel paint, complete all as specified and as directed.

Preparation of roof surfaces by scrubbing down with steel brushes and cleaning with water all loose dirt/dust and roughening old concrete roof surfaces and applying cement slurry with 3.0 Kg of cement per Sqm and applying the following Roof Treatment complete all as directed :- (a) Applying 1st course of 10mm thick screed bed with cement mortar 1:3 over concrete surface. (b) Applying 2nd course of bituminous primer conforming to IS-3384 @ 0.4 Kg/Sqm over the screed bed. (c) Applying 3rd coarse of a coat of blown type bitumen of grade 85/25 heating to a working temperature of 180° C and applied @ 1.2 Kg/Sqm.

(d) Applying 4th course of APP (Atactic Polypropylene) modified polymeric membrane 3mm thick weight not less than 3.6 Kilogram/Square Metre with 160 Grams/Square Metre non woven polyester made at centre core reinforced laid with 75 mm side overlap and 100 mm overlap. The membrane has to be laid with LPG torch and overlap sealed and finished neat. (e) Applying 5th course of a coat of bonding material with blown type bitumen of grade 85/25 heating to a working temperature of 180° C and applied @ 1.2 Kg/Sqm. (f) Applying two coats of aluminium paint over APP membrane complete all as specified and as directed.

Dismantling of CI/ PVC/ Reinforced concrete pipes of 75mm dia, jointed in cement mortar complete all as directed.

Cast iron soil, waste and vent pipes, 75 mm in any length with or without ears, with cement joints, fixed to wall complete all as specified and directed.

Cast iron Bends (any radius), diminishing pieces or tapers (larger bore measured) with oval access door for 75mm bore pipe, complete all as specified and directed.

Cast iron cowls for 75mm bore pipe, complete all as specified and directed.

Cutting into existing manholes for connecting new drains, making good to pipe and rendering, cutting out existing benching for and forming branch channel (1/2 round or 3/4 section) in cement concrete 1:2:4 type B-l smooth finished, and reforming benching as required for 150mm internal bore pipe, complete all as specified and directed.

Demolition and breaking up 150mm dia salt glazed stone ware drain pipes (Salt glazed ware, AC or Reinforced concrete) set in cement mortar complete all as specified and directed.

Salt glazed stone ware (SGSW) drain pipes of grade 'A' 150mm bore laid in trenches and jointed on concrete bed complete all as specified and directed.

Concrete bed to drain pipes including packing under and haunching against the sides of pipes after they are laid and tested, for 150mm bore of pipe plain cement concrete 1:4:8 type D-2 (Using 40mm graded stone aggregates) complete all as specified and directed.

E/M Portion

Taking out carefully copper/aluminium point wiring, (Light, fan, socket or power) complete with all fitting, fixtures such as switch socket out let, ceiling rose, holder, regulator, DB's etc. including making good the disturbed surface of wall/floors, complete all as specified and as directed.

Point wiring with multi stranded copper conductor of size 1.5Sqmm PVC insulated unsheathed FRLS cable in existing rigid PVC concealed conduit and accessories of suitable size for concealed wiring including 1.50 Sqmm copper earth wire (green colour) FRLS Cable for one light point or fan point or bell point controlled by one No, one way switch using cable of different insulation colour for colour coding including 3mm thick laminated sheet cover, mild steel sheet or cast iron boxes including cutting chases and making good to disturbed surfaces of wall / floor, complete all as specified and as directed.

All as per the description of Serial Item No 90 here-in-before but for one 3 pin socket outlet 5 Amp independent, complete all as specified and as directed.

All as per the description of Serial Item No 90 here-in-before but for one 3 pin socket outlet 5 Amp on same board, complete all as specified and as directed.

All as per the description of Serial Item No 90 here-in-before but for one 3 pin socket outlet 15 Amp independent board using cable of size 2.5 Sqmm conduit all as specified and directed.

Point wiring with multi stranded copper conductor of size 1.5Sqmm PVC insulated unsheathed FRLS cable in and including PVC casing and capping and accessories of suitable size for concealed wiring including 1.50 Sqmm copper earth wire (green colour) FRLS Cable for one light point or fan point or bell point controlled by one No, one way switch using cable of different insulation colour for colour coding including 3mm thick laminated sheet cover, mild steel sheet or cast iron boxes including making good to disturbed surfaces of wall / floor, complete all as specified and as directed.

All as per the description of Serial Item No 94 here-in-before but for one 3 pin socket outlet 5 Amp independent, complete all as specified and as directed.

All as per the description of Serial Item No 94 here-in-before but for one 3 pin socket outlet 5 Amp on same board, complete all as specified and as directed.

All as per the description of Serial Item No 94 here-in-before but for one 3 pin socket outlet 15 Amp independent board using cable of size 2.5 Sqmm conduit all as specified and directed.

Point wiring with multi stranded copper conductor of size 2.5Sqmm PVC insulated unsheathed FRLS cable in and including rigid PVC concealed conduit and accessories of suitable size for concealed wiring including 1.50 Sqmm copper earth wire (green colour) FRLS Cable for one light point or fan point or bell point controlled by one No, one way switch using cable of different insulation colour for colour coding including 3mm thick laminated sheet cover, mild steel sheet or cast iron boxes including cutting chases and making good to disturbed surfaces of wall / floor, complete all as specified and as directed.

Switch piano, flush type, 5 Amps, single pole, one way, complete all as specified and as directed.

Switch socket outlet combination universal type, 2 in 1, 3 pin 5 and 15 Amp, piano flush type, 240 volts, complete all as specified and as directed.

Socket out let 3 pin 5 Amp, piano flush type, 240 volts, complete all as specified and as directed.

Ceiling rose surface bakelite three terminals 240 volts complete all as specified and as directed.

Lamp holder PVC case body of Bakelite with back plate suitable for batten fittings complete all as specified and as directed.

Electronic fan regulator stepped type with five step 240 volts 100 watt suitable for 1200mm / 1400mm sweep AC ceiling fan including taking out the unserviceable, complete all as specified and as directed.

LED Lamp 230 volt 09 watts, in white colour with Max Lumen output (850 lm) and colour temp 3000K, complete all as specified and as directed. Make : Havells / Crompton Greaves / Philips / Wipro

Tube light fitting box type suitable for and including LED 20 tube Rod 4' long with decorative colour in polycarbonate housing and all accessories pre-wired and making connections with three core copper flexible cable of size 23/0.0076 from ceiling rose to PVC connector to light fitting complete all as specified and as directed. Make : Havells 'E-Lite LED Curve' Cat Part No LHEXBXPNIN1W020 or equivalent in Philips / Wipro / Crompton

Bulk head luminaries complete with all accessories suitable for and including 1 x 10 Watts LED lamp including connecting up with twin core twisted flexible copper conductor cable with suitable size of 230 Volts 50 Hz complete all as specified and as directed. Make : Havells Cat Part No LHEOAOP7UZ6W010 / Crompton Cat Part No LBHE-10-CDL

Sheet metal enclosure factory made double door for DB 415 volts with 200 Amps rated bus bar TPN 4 Way including taking down and making good disturbed surfaces of walls, complete all as specified and as directed.

Sheet metal enclosure factory made double door for DB 240 volts with 200 Amps rated bus bar SPN 4 Way including taking down and making good disturbed surfaces of walls, complete all as specified and as directed.

Sheet metal enclosure factory made double door for DB 240 volts with 200 Amps rated bus bar SPN 8 Way including taking down and making good disturbed surfaces of walls, complete all as specified and as directed.

Sheet metal enclosure factory made double door for DB 240 volts with 200 Amps rated bus bar SPN 12 Way including taking down and making good disturbed surfaces of walls, complete all as specified and as directed.

MCB TPN 63 Amp, 415 V, 50 Hz, 10 KA 'C' Series, complete all as specified and as directed.

MCB SPN 63 Amp, 240 V, 50 Hz, 10 KA 'C' Series, complete all as specified and as directed.

MCB SPN 40 Amp, 240 V, 50 Hz, 10 KA 'C' Series, complete all as specified and as directed.

MCB SPN 32 Amp, 240 V, 50 Hz, 10 KA 'C' Series, complete all as specified and as directed.

MCB SP 6 to 32 Amp, 240 V, 50 Hz, 10 KA 'C' Series, complete all as specified and as directed.

1100 Volt grade heavy duty cable PVC Insulated aluminium conductor, served with inner sheathing of PVC tape and over all PVC sheathed in service connection suspended by insulating hanger not more than 1 mtr apart including 4 mm suspension wire, one twin core cable flat or circular 16 sqmm stranded conductor, including taking down old unserviceable service connection complete all as specified and directed.

1100 Volt grade heavy duty cable PVC Insulated aluminium conductor, served with inner sheathing of PVC tape and over all PVC sheathed in service connection suspended by insulating hanger not more than 1 mtr apart including 4 mm suspension wire, one twin core cable flat or circular 10 sqmm stranded conductor, including taking down old unserviceable service connection complete all as specified and directed.

Supply and laying or passing through pipe XLPE insulated armoured heavy duty electric cable with aluminium conductor 1100 volts grade ISI marked cross sectional area 25 Sqmm 3.5 core on wall including taking down old cable, complete all as specified and as directed.

Street Light fitting 60 Watts LED made up of pressure die cast aluminium housing with high power LED as lighting source and lens embedded PC cover having top opening separate driver compartment with IP66 protection and impact resistance of IK07 with 10KV built-in surge protection device including taking down old unserviceable Street Light Fitting any type complete, all as specified and as directed. Make : Havells 'Endura Pearl Neo' Cat Part No SL60WLED757PASYTOPC or equivalent in Wipro / Philips / Crompton

Cutting of existing GI pipe two cuts and insertion of tee 15x15x15mm with nipples, unions and threasing etc and making good disturb surfaces matching with existing area all as specified and directed by Engr-in-charge.

Excavating in trenches, not exceeding 1.5metre wide and not exceeding 1.5metre depth for foundation, etc., and getting out in any type of soil, complete all as specified and directed.

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exceeding 25 cm thick any type of soil, complete all as specified and directed.

Removing excavated soils to a distance exceeding 50m but not exceeding 100m and depositing where directed at a level not exceeding 1.5m above the starting point complete all as specified and directed.

Sand cushioning to underground cables using new dry river sand laid in trenches 8cm thick below the cable and 15cm thick above the cable after laying and stretching the cable complete, punned to 18cm, complete all as specified and directed Note : Punned thickness of 18cms shall be measured for payment.

Supply and laying brick covering with width equal to length of bricks as mechanical protection to underground cable using old size sub class 'B' bricks, laid flat size 230mm x 115mm x 75 mm with width of brick perpendicular to length of cable, all as specified and as directed.

Storage water heater (Geyser), vertical type, of 25 ltr capacity of inner tank, outer tank, syphon assembly, thermostat heating element, safety valve etc complete all as per manufacturer design and specifications including making of all fixing arrangements complete having BEE Five Star Rating including grouting of nuts and bolts and necessary PCC work as specified and directed by Engineer-in-Charge. Make:- VENUS 'SPLASH 02 GL' / RACOLD 'ETERNO 2 25 V' / BAJAJ 'MAJESTY 25L GMU' / HAVELLS 'PURO PLUS 25L'

Supply & fixing stop valves, 15mm bore, fancy type, chromium plated with long shank and cup (concealed type), cast copper alloy, screwed down, high pressure with crutch or butterfly handle, both ends screwed for iron pipe or for union etc., fixed in repair, complete all as specified & directed.

PVC connection 90cm long fitted with PTMT nut and washer on both ends, fixed to 15mm bore iron pipes, complete all as specified and directed.

Earthing complete with galvanized mild steel earth plate electrode size 600mm x 600mm x 6mm thick buried directly in ground (preferably in vertical position) earth pit not less than 2.25 meter below normal ground level with top edge of the earth plate not less 3 meter (BGL) connected to galvanized iron earth lead wire 4mm dia by means of bolts, nuts, check nut and washer of galvanized iron including PCC pit in RCC 1:2:4 type B-1, precast RCC cover with suitable handle, excavation and earth work in any type of soil, 20mm bore “medium grade” galvanized iron water tubing fixed with cast iron funnel and wire mesh and 15mm bore “light grade” galvanized iron protection pipe for earth lead wire upto 5m length, charcoal, common salt, complete all as shown in EP No 3 of SSR 2009 Part-I, connected to test point complete, all as specified and testing on completion.

M S BANSI LAL CONSTRUCTION CO

RAJINDRA ENGINEERS & CONTRACTORS

M/s Ashok Kumar

BALVINDER SINGH AND SONS

JK BUILDERS AND DEVELOPERS

AKSHAY CONSTRUCTION COMPANY

M/S RANADHAWA

Bidder Name

AKSHAY CONSTRUCTION COMPANY

M S BANSI LAL CONSTRUCTION CO

RAJINDRA ENGINEERS & CONTRACTORS

BALVINDER SINGH AND SONS

M/S RANADHAWA

JK BUILDERS AND DEVELOPERS

KOHLI CONSTRUCTION CO

M/s Ashok Kumar