SPECIAL REPAIR TO BLDG NO. BCD-30 AND BCD -31 (TOILET BLOCK) IN ZONE 9A AT TALBEHAT MIL STN

Amount

Taking down cement or cement lime plaster on brick wall, ceiling incl. Raking out joints, hacking for key, scrubbing down with water etc complete all as specified and directed.

M&L for Rendering 10mm thick on in CM 1:6 fair faces of brick work or concrete surfaces fair surfaces of walls finished even and smooth w/o using extra cement complete all as specified and directed.

M&L for Rendering 15mm thick in cement mortar 1:4 on fair faces of brick work or concrete surfaces of walls finished even and smooth complete all as specified and directed.

Complete removal of existing treatment of old plastered surfaces of wall over a coat of primer on surface and applying two coats of oil bound distemper complete all as specified and directed.

M&L for preparation of new plastered surfaces of wall over 1mm thick putty a coat of primer on surface and applying two coats of oil bound distemper complete all as specified and directed.Make : Tractor Uno (Asian paints)/Jadoo (Berger paints)/Nerolac beauty (Nerolac paints)as approved by AGE(I).

M&L for preparation of plastered surfaces of wall and applying two coat of weather proof exterior emulsion paint complete all as specified and as directed. Make : Apex Ultima protek (Asian paints).

M&L for preparation of old plastered or un-plastered surface including brooming down or steel wire brushing, scrapping down smoke soot, moulds, moss and efflorescent salts and trading oil and greasy spots and applying one coat of weather proof exterior emulsion paint complete all as specified and as directed. Make : Apex Ultima protek (Asian paints).

Supply only integral water proofing compound

Dismantling of AC sheet (corrugated or semi corrugated etc) including AC ridges in large patches as in roof covering complete all as specified and as directed. Note:- opening of existing wind tie where required for taking down of AC sheet is deemed to be included in the rate quoted .

Dismantling of timber scantling 40 Sqcm and over in section in any position such as in rafter, purlins etc in unframed work complete all as specified and as directed

Dismantling of timber fillets , rails, posts, rafters, purlin etc under 40 sqcm in section, in any position in unframed work complete all as specified and as directed.

M&L for 2nd class hard wood exc 13 & n exc 25 Sqcm plain fillets, square, rectangular in section, clean sawn, secured with nails or brads complete all as specified and directed

M&L for clean sawn 2nd class hard wood as in scantling more than 40 Sqcm in sectional area fixed to timber/iron frame work complete all as specified and as directed Engr-in-Charge

Cutting holes into or through brick wall built in cement lime mortar and walls of cement concrete of superficial area exc 150 sqcm but n exc 400 sqcm and making good in CM 1:3 or cement concrete 1:2:4 type B-1 as required.

S&F rolled mild steel section work as in main and cross beam, hip and jack rafters purlins where connected to common rafters and running rails and guides for sliding door fixed with angle cleats or other connecting plates and cooler stand and similar work confirming to Fe 410W(Gde E-250 quality A) complete all as specified

S&F Pre-painted galvalume aluminium zinc coating AZ-150 GI based corrugated steel sheet 0.5 mm thick, Trapezoidal roofing profile with 190 mm Pitch & 29 mm depth of profile of any colour having tensile strength of 550 Mpa fixed with self tapping screws as specified & directed.

S&F Pre-painted galvalume aluminium zinc coating AZ-150 GI based corrugated steel sheet 0.5 mm thick,Trapezoidal roofing profile with 190 mm Pitch & 29 mm depth of profile of any colour having tensile strength of 550 Mpa fixed with self tapping screws as specified & directed.(For sun shed)

S&F Pre-painted galvalume aluminium zinc coating AZ-150 GI based plain steel sheet 0.5 mm thick of any colour having tensile strength of 550 Mpa fixed with self tapping screws as specified & directed.

Demolition of cement concrete (unreinforeced) in floors and paving n.exc 15cm thickness (above or below ground level) complete all as specified and directed.

Demolition of stone/ brick masonry built in cement or cement lime mortar as in portion ordered and directed.

M&L for brick work with old size sub class B bricks straight or curved on plan exc 6m mean radius built in CM 1:6 complete all as specified and directed.

Material & Labour for brick work with fly ash bricks built in CM 1:4, straight or curved on plan exceeding 6 M mean radius using old size bricks in half brick thick wall etc.

M&L for PCC 1:2:4 type B-0 using 12.5 mm graded stone aggregate as in coping and like other wk including necessary form work complete all as specified and directed by Engr-in-charge.

M&L PCC (1:3:6) type C-2 using 20mm graded stone aggregate 75 mm thick as in plinth protection finished fair even laid in alternate bays n.exc 2m in length all as specified and directed.

Taking down chowkhats or frames with shutters (without taking off shutters from the frames) n exc 1.50 sqm each and removing from site spd and directed.

Taking down chowkhats or frames with shutters (without taking off shutters from the frames) exc 1.50 sqm and n.exc 4.00 Sqm each and removing from site completeall as specified and directed.

Supply and fixing, made 100% Solid WPC (Wood Polymer Composite) Door Frames of cross section 45 mm x 70 mm (moulded) having single rebated made from Wood Polymer Composite (Single Extruded Process) material comprising of virgin PVC polymer of K-Value 57-60 (Suspension Grade), calcium carbonate and natural fibres (wood powder/ruce husk/wheat husk)and non toxic additives fabricated with meter joints after applying PVC solvent cement & screwed with full body treated star headed screws having minimum frame density of 780 Kg/cbm & manufactured by "Rajshri/Echon or Eq" an ISO 9001-2015 certified company, having good screw holding capacity (Screw withdrawal strength of (Min, 990N) Minimum compressive strength of 58 N/mm2, modulus of elasticity 900N/mm2 and resistance to spread of flame of class A category with property of being termite/borer prof, water/moisture proof & fire retardant & fixed in position with and including SS Dsh Fasteners/Hold Fast of required dia and length, all as per specifications drawings as directed,. Material test certificate and authentication should be compoulsory provided by the manufacturing company.

S&F factory made single extruded WPC (Wood Polymer Composite) solid decorative type flush door shutter of size 30mm thick comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N / m2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fie retardant WPC to be laminated with PVC foil of minimum 14 micron thick of approved design pasted with hot melt adhesive on both faces of shutter and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk SS screws, all as per direction of Engr-in-Charge. (Note : Stainless steel butt hinges and necessary SS screws shall be paid separately).

Supply & fixed 200 mm long aluminium anbodised barrel tower bolts of extruded section and fixed complete all as specified and directed.

Supply & fixed 150 mm long Extruded aluminium alloy handles, fabricated type anodised complete all as specified.

S&F 100 mm long stainless steel butt hinges with galvanised MS hinge pin etc.

S&F alluminum alloy, anodised, cast type or extruded section, sliding door bolt with hasp & staple (bolt type) with fixing clips and bolts and 300 mm long complete all as specified.

S&F powder coated Anodised aluminium frame for doors, windows, ventilators with one or more rebates including joining cleat for fixing etc. complete all as specified directed by Engr-in-charge. (Jindal sec 21516,21517)

S&F powder coated Anodised aluminium window and ventilator shutters, fixed type without sash bar, aluminium section weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws etc. complete all as specified specified and directed by Engineer-in-Charge. Note:- Glass and Wiremesh paid Seprately.

S&F in position 4.8mm thick frosted glass on one side quality and glazing with glazing clips including necessary rubber packing to aluminium framen n. exc 0.5 sqm in each pane all as specified and as directed.

S&F Stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staplescompleted all as spd & directed.

M&L for Framed work such as grills,gratings, etc. with ends of bars shouldered and/or riveted,or forged into spikes; framedguard bars; barred iron doors,ladders; framed balusters; walkways; railings; framework of water tanks and similar workconforming to Fe.290.Gde-E-165 complete all as specified and directed.

Dismantling floor, hearth or wall tilling including cement mortar bedding, and rubbish off premises etc complete all as specified and directed.

M & L for Cement concrete type B-0, 1:2:4 (12.5 mm graded aggregate), 100 mm thick in sub base of flooring etc, complete all as specified and directed.

M & L for digital HD coloured Ceramic tiles 7 to 8 mm thick ( square /Rectangular) area of each tile exceeding 0.11 sqm but not exc 0.18 sqm in floors etc set and jointed in neat cement slurry and pointed in white cement to match with tile laid over and including screed bed or bedding layer of 15 mm thick in CM (1:6), complete all as specified and directed.

M & L for digital HD coloured Ceramic tiles 7 to 8 mm thick ( square /Rectangular) area of each tile exceeding 0.38 sqm but not exc 0.72 sqm on walls, set and jointed in neat cement slurry and pointed in white or coloured cement to match with tile over and including cement mortar 1:4, 10mm thick plaster complete all as spd & directed.

Dismantling of existing unserviceable water tank of any description capacity exc 500 Ltr but n.exc 1000trs capacity each complete all as specified and directed

S& F rotational moulded tripple layered water storage tank 1000 litre capacity (cylindrical vertical with closed top) hoisted & fixed in position all as specified in SSR Part-I complete all as spd & directed.

S&F Ball valves high pressure of PTMT with epoxy coated Aluminium rod & highdensity plastic ball screwed for iron pipe and fixed. (Minimum weight 15mm-142gms/ 2 0 m m - 2 1 0 g m s . / 25mm-455gms/ 40mm - 690 gms) complete all as spd & directed.

S&F in repairs gun metal globe or gate valve, wheel head cast copper alloy screwed down light pressure with crutch or butterfly handle screwed both ends for iron pipe or for union 20 mm dia, ISI marked complete all as spd & directed.

Taking up or down steel tubing and connection 20 mm bore and removing the same from site/keeping aside for reuse complete all as specified and directed.

Taking up or down steel tubing and connection 20 mm bore and removing the same from site/keeping aside for reuse complete all as specified and directed.

S & F water tubing 20 mm bore, medium weight, ISI marked galvanized with all fittings and fixed to walls, ceiling or laid in floors complete all as specified and directed.

All as per srl item above but 25 mm bore

Supply & fixed 50mm bore LDPE (Low density Polyethylene Pipes) of pressure rating 6Kgf/Sqcm fixed complete to walls,ceilings or in floors including taking down of old GI tubing, 40 mm bore all as specified and directed.

S&F in repair PVC valveless syphonic action type low level flushing cistern, 10 Ltrs capacity White, with inlet ball valve, float, handle with 32mm PVC flush pipe, fixed on walls by driling holes and using PVC rawl plug of suitable size complete all as specified and directed.

Supply and fixing in repairs Vitreous China W.H.B. white oval type counter below type of size 570 x 445 mm including waste coupling, waste pipe and brackets etc. complete all as specified.

Supply and fixing , vitreous China squatting pan of Orrisa pattern size 580mmx440mm white (Ist quality) with ‘P’ or ’S’ trap, front or back inlet and integral foot rests of any pattern complete including provision of lime concrete bedding, trap and connection to flush pipe complete all as specified.

Supply and fixing in repairs vitreous china premium quality/1st quality wash down water closet pan (pedestal pattern), white (excluding flushing cistern & flush pipe) & incl 01 No ‘P’ or ‘S’ trap of dia 100mm including provn of lime concrete bedding, complete all as specified.

Supply & fixed in repair Vitreous China urinals, half stall type (back or corner wall type), complete including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including 60mm long brass screws, pointing around urinal back in cement; fixing automatic flushing cistern with brackets, flush pipe, grating and Union for discharge pipe. (Exclusive of fixing supply pipe to flushing cistern, trap and waste pipe) complete all as specified.

Supply and fixing in repairs, Urinal spreader of Brass chromium plated for fixing with 15 mm dia pipe., compete all as specified.

Supply and fixing in repairs,15mm bore pillar tap, fancy type, chromium plated cast copper alloy with capstan head, screwed down high pressure, with or without lettered ‘Hot’ or ‘Cold’ with long screwed shanks , compete all as specified.

Supply and fixing in repair, bib tap screwed down high pressure, cast copper alloy,fancy type, ISI marked, with crutch or butterfly handles screwed down suitable for 15mm bore pipe or union, complete all as specified.

Supply and fixing (in repair) angle cock 15mm dia chromium plated, cast copper alloy, screwed down, high pressure with crutch or butter fly handle, screwed both ends for iron pipes or unions, complete all as specified. (Note : Weight of cock shall not be less than 0.575kg)

Supply & fixed in repair PVC connections 45cm long including 15mm bore PTMT nuts on both ends complete all as specified.

S&F in repair 15mm bore concealed stop valve type chromium plated cast copper alloy screwed down high pressure screwed both ends for iron pipe or for union all as specified and directed by Engr-in-charge.

S&F in repair brass chromium plated tubular towel rail 20mm dia 'D' type 60cm long between flanges all as specified and directed by Engr-in-charge.

Supply & fixed in repairs stainless steel grating openable 100mm dia without hole including fixing with white cement complete all as specified.

Supply & fixed in repairs stainless steel grating openable 100mm dia with hole including fixing with white cement complete all as specified.

Supply & fixed in repair fancy type shower rose125mm dia size of Rim and 30cm long CP brass pipe with swiwel joint complete all as specified.

S&F in repair Soap dish, any type, fixed to plugs with chromium plated brass screws embedded in the wall complete all as sped & directed.

S&F in repairs Health faucet (ABS Body) mild steel chromium plated suitable for 15 mm dia pipe with 1.25 metre long flexible tube and ABS wall hook including making connections and fixed in position complete in all respect as specified and as directed.

Taking down rainwater pipes (any size or pattern), including all fittings, heads, shoes, bends, swan-necks, etc., and removal complete and all as specified and directed

S&F for 110 mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to walls or floor.

S&F for 110 mm bore PVC (SWR) vent cowl complete all as specified and directed.

S&F Stack clamps out of 50 mm by 5 mm flat iron and 16mm dia round iron stays, including bolts and nuts and securing ends of stays to wall or roof fixed to pipe of bore 110mm complete all as specified.

S&F 110mm PVC (SWR) bends any radius

S&F 110mm PVC (SWR) branch piece, single (single Y) equal or unequal

PVC (SWR) branch piece, double (double Y) equal or unequal

Demolition of reinforced cement concrete of any description and in any position not otherwise specifically provided for complete all as specified and directed. Note: All debris obtained from demolition shall be removed 1.5km to 2km complete all as specified and as directed.

Providing precast cement concrete type B1 1:2:4 20 mm graded aggregate as in cover slabs for septic tank/ manholes/drains set in cement Mortar 1:4 complete all as specified and as directed.

M&L TMT bars 10 mm dia and over cut to length bend to shape required incl. cranking hooking ends and binding with and incl. MS wire (annealed) not less than 0.9 mm dia or securing with clips complete all as specified and as directed

Demolition and breaking up 150 mm dia (Salt glazed ware ,AC / CI or reinforced concrete) set in cement mortor drain pipe, jointed set in cement mortor.incl pcc if any and taking out of trenches,floor & walls if required complete all as specified and directed.

M&L for 150 mm bore SGSW drain pipe (Grade-A) laid in trenches and jointed in CM 1:1 and tested complete all as specified and directed. Make:

M&L for concrete bed for 150 mm bore pipe in laid with PCC 1:4:8 type D-2 to drain pipes including packing under, haunching against the sides of pipes after they are laid and tested complete all as specified and directed.

Excavation in trenches not exceeding 1.5 m wide and not exceeding 1.5 m in depth and getting out in soft/loose soil etc. including trimming bottom and sides of trenches, leveling/ grading and ramming bottom of excavation complete all as specified and directed.

Returning, filing in, including spreading, levelling, watering and well ramming in layers not exceeding 25 cm thick in soft/loose soil complete all as specified and directed.

Removing surplus excavated soil to a distance exc 250m but n/exc 500m and depositing where directed

M&L for PCC 1:4:8, type D-2 using 40mm graded stone aggregate as in foundations, fillings, mass concreting complete all as specified and directed.

Taking down carefully copper/Aluminium point wiring (light/fan/socket or power) complete, including fixture and fittings such as switches, ceiling roses, pendants, regulators, sockets etc, removing materials to store for keeping in safe custody or for taking credit (credit for above items should be made as per conditions separately) and making good disturbed surfaces of wall, floors etc complete all as directed.

Taking down carefully complete light fittings removing materials to store for keeping in safe custody or for taking credit (credit for above items should be made as per conditions separately) and making good disturbed surfaces of wall, floors etc complete all as directed.

Taking down Distribution Boards along with MCB's incl removing the same from site and making good to the disturbed surface complete

Taking down existing sub main wiring of any type and description including removal of teak wood batten/pipe etc complete

M/L for point wiring concealed type with 1.5sq mm FRLS PVC insulated unsheathed single core multistranded copper conductor cable 1100 volts grade incl 1.5 Sq mm PVC insulated unsheathed copper conductor cable as earth continuity conductor drown through in and incl FRLS PVC rigid conduit not less than 20 mm dia with its accessories pressed steel terminal box incl 3mm thick ISI marked laminated sheet cover for fixing switches/socket/regulators and making good disturbed surfaces of wall, floors etc for the following :- Wire: Make - Finolex/V-guard/Polycab/KEI/Havells/Plaza PVC conduit: Make -Polycab/Precision/Plaza/Kalinga Note:- On RCC ceiling/column, false ceiling, AC/Metallic Sheet ceiling wiring done on surface with conduit/PVC Casing capping and its accessories.

One light/fan/bell point controlled by one No piano type switch 5 Amps single pole one way

One socket outlet 5/3 pin 6 Amps controlled by one switch on the same board

One socket outlet 5/3 pin 6 Amps controlled by one switch on the same board.

All as per item NO 90 above but 3 pin socket out let 15/16 Amps on the independent Board all as spfd with single core unsheathed PVC insulated cable multistranded copper conductor of size 2.5 sq mm for phase & neutral & 2.5 sq mm for earth continuity conductor

S&F Switch Piano Flush button single pole one way 5/6 Amp.

Piano Flush button single pole one way 15/16 Amp

S&F socket outlet 2 in 1, 3 pin & 2 pin, 5/6 Amp, 240 volt

S&F socket outlet 2 in 1, 3 pin & 2 pin, 5/6 Amp and 15/16 Amp, 240 volt.

S&F ceiling rose surface bakelite 65mmx50mm 100watt three terminal.

S&F Lamp holder Batten holder PVC/Polycarbonate insulated body with metal ring and back plate for batten fitting

M&L concealed sub main wiring with two single core PVC FRLS insulated unsheathed stranded copper conductor cable FRLS, 02 runs of 01 Single core of size 6 sqmm (for main current) drawn in & incl PVC conduit conduit less than 20mm dia ISI marked with all accessories such as tee, bend, joint cover etc round / square blocks at junctions etc, all as per site requirements ISI marked with one run of 01 Single core of size 6 Sqmm (As earth wire) PVC insulated unsheathed stranded copper conductor as a continuous earth wire complete all as specified incl. taking down old unserviceable sub main wiring and colour coding of cables such as Phase - Red, Neutral – Black, and Earth – Green complete all as directed by Engineer-in-Charge PVC conduit: Make -Polycab/Precision/Plaza (i). One run of conduit two run of 6 Sqmm copper conductor & One run of 6.0 Sqmm coper conductor is measured as one unit (ii). On RCC ceiling/column, false ceiling, AC/Metallic Sheet ceiling wiring done on surface with conduit and S&F in replacement single pole and neutral enclosure with a two pin and earth socket complete

S&F in replacement single pole and neutral enclosure with a two pin and earth socket complete with top and one single pole MCB of 20 Amp 240 volt and making good to the disturbed surface complete Make: Legrand/Cchneider/Indo Asian/Siemens/Havells

S&F sheet metal enclosure double door for MCB DB single pole and neutral 4 way with 200 Amps, 240 volts double door (Metallic) type Make- Legrand/Hager/Schneider/ndoAsian/Siemens

S&F vertical sheet metal enclosure double door for MCCB DB Triple pole and neutral 4 way, (4+12) with 200 Amps rated bus bar 440 volts earth dolly IP-43, IK09, and making good to the disturbed surface complete

S&F MCB SP 6 to 32 Amps rating 240 volts C curve, 10 KA, 50 Hz, of poles and current carrying capacity in the MCB DB complete with connection testing and commissioning confirming to SitEC-60898-1 Make-As approved Make of DB

S&F MCB SPN 40 to 63 Amps rating 240 volts C curve 10 KA 50 Hz, of poles and current carrying capacity in the MCB DB complete with connection testing and commissioning confirming to IS/IEC-60898-1. Make As approved Make of DB

S&F MCCB 4 pole 63 Amp, 440 volt 'C' series, 16 KA, 50 Hz, confirming to IS/IEC-60898-1 Make-As approved Make of DB

Supply and fixing exhaust fan madde of sturdy engineering plastic body complete with lovers shutters, AC single Phase, 230 V of size 300 mm sweep copper winding with blades and frame and lovers shutters, RPM 1200 complete all as specified and as directed by Engineer- in - Charge Make : Havells/CG

M & L for cutting of hole 300mm dia at 9" wall for exhaust fan including PCC (1:3:6) type C-1 and one coat of exsiting white wash over distrubed area complete all as sopecified and directed by Engineer - in- Charge

Supply and fixing LED 4 batten light 18/20 Watt 230 Volt, complete connection with PVC insulated multi stranded copper flexible wire twin core of suitable size from nearest source complete all as specified and as directed by Engineer-in-Charge Make Havells/Surya/Crompton/Philips/Baial

Supply and fixing complete LED light fittings mirror type with high out put diffuser 2 feet, 10 watt 220 V AC decorative type with driver, holder and LED tube light including connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete Make Havells/Surya/CG/Phillips

Material and Labour for earthing complete with galvanized steel earth plate electrode 600 x 600 x 6 mm thick buried directly in ground( earth pit not less than 2.25 meter deep below ground level) with top edge of plate not less than 1.5 meter below normal ground level, connected to galvanized iron earth lead 4 mm dia by means of bolts, nuts, check nuts and washers of galvanized iron or steel, all fSSR PtIincluding necessary excavation and earth work PCC (1:3:6) type C-1 with 50 mm thick cast RCC ( 1:2:4) type B-1 cover slab framed with 50X30X4 mm MS angle (reinforced with 6 mm dia defomed bar @ 15 cm CIC both ways and suitable handle of 10 mm dia round bar) including providing horenal or coke and magnesium sulphate in alternate layers of 15 cm compacted thickness all around the earth electrode, with funnel and 20 mm bore galvanized iron watering pipe (medium grade) wire mesh conner luas. complete in all respect., GI earth wire protected by 15 mm bore (light grade) galvanized iron pipe and other end connected to the earth bar (test point) made of MS flat (40OX32X6 mm) bend in D shape and fixed to wall by means of fast nut or bolt grouted in to wall at 1 mntr from plinth height. 4sgmm PVC insulated (colour green) copper conductor single run as earth continuity conductor along with 15 mm PVC conduit grouted in wall or fixed on wall surface to be continued up to main switch board and fix with common earth dolly as directed by EIC. Disposal of soil to a distance not exceeding 50 mtr and necessary A/U 5 Each as shown in electrical plate e testing on completion complete all as specified and as directed. 23.00 Supply and fixing in repair of wooden doors with hinges and paint with colour as existing on Meter box/ DB Each Job Box complete all as specified and directed. 24.00 Supply and fixing LED Inverter Lamp Make : Shakti Cat Part No -SZBLB22009 - iBB 9W B22 or equivalent complete all as specified and directed. Make: Havells/ Philips/Surya /Crompton/Halonix/ Shakti 25.00 Supply and foxing Inverter Batten T/L fiting Make: Shakti Cat Part No - SZSLBMX018-iBB 18W 4 ft or equivalent complete all as specified and directed. Make: Havells/ Philips/Surya /Crompton/Halonix/ Shakti

Supply and foing in repair of wooden doors with hinges and paint with colour as existing on Meter box DB Bos complete af as specified and directed

Supply and fixing LED Inverter Lamp Make Shakti Cat Part No-SZBLB22009-BB 9W B22 or equivalent and directed: Maka: Havelis/ Philips/Surya/Crompton/lalonix/ Shakt complete all as specified and

Supply and fixing Inverter Batten T/L fitting Make Shakti Cat Part No SZSLBMX018-1BB 18V 4 It or equivalent complete all as specified and directed Make: Havells/ Philips/Surya/Crompton/Halonix/Shakti

M & L House service bracket (hook type complete with 3.00 m long G.I pipe 40mm dia Medium grade, Two Nos 90 degree bends. MS hook and stay or guy complete all as specified and directed

Supply and fixing 1100 volts grade heavy duty cable PVC insulated aluminium conductor served with inner sheathing of PVC tape and overall PVC sheathed in service connections suspended by insulating hangers not more than 1 metre apart including 4 connections suspended by insulating hangers not more than 1 metre apart including 4 mm suspension wire, of solid conductor one twin core cable flat or circular complete all as specified and as directed

Supply and laying or fixing or passing through pipe, 1100 volts grade heavy duty calbe with PVC insulated aluminium conductor served with an inner sheathing of PVC tape armoured with galvanised steel wire or tape and overall PVC sheathed 10 sq. mm nominal cross section 04 core solid conductor in service connection complete all as

Supply and fixing LED building security light fitting, 15/20 Watt made up of pressure die cast aluminium housing, inbuilt driver, top opening, IP 66, 230 Volt, complete conncection with PVC insulated multi stranded copper flexible wire twin core of suitable size from nearest source complete all as specified and as directed by Engineer-in-Charge, Make Havells/ Surys/ Crompton/ Philips.

Supply and fixing building security light bracket bend type complete with 2.0m long G.I pipe 40mm dia light grade, with suitable clamp and nut bolts complete all as specified and directed by Engineer-in -Charge.

Supply and laying of fixing in replacement GI tubes light grade 40 mm dia, on place of rusted GI pipe in support of Earth/ Cables. On roof/Pole/wall/laid in floor/in trenches. Make :- JINDAL/TATA/PRAKASH.

Note :- Debris obtained from all items should be removed in low lying areas as directed by Engr-in-charge out of MOD Land. (Rates quoted for items are deemed to be included for this, where removal of debris in the items is not considered.)

M/S SHIVA TRADERS (BID ID -3499732)

PRATAP CONSTRUCTION (BID ID -3499185)

M/S SALONI ENTERPRISES (BID ID -3498403)

M/s Indu Enterprises (BID ID -3499248)

M/S Chadha Brothers (BID ID -3497274)

M/S R.S.BUNDELA & SONS (BID ID -3499914)