PROVISION OF 200 KVA TROLLY MOUNTED DG SET AND 250 KVA DG SET AT PUMP PROVISION OF 200 KVA TROLLY MOUNTED DG SET AND 250 KVA DG SET AT PUMP

Amount

NOTE (Applicable for all items):- The bidders/contractors are advised to read tender document & all corrigendum/ amendments and General conditions of contracts before entrying/quoting the rates. SCHEDULE 'A'

Surface dressing not exceeding 30 cm and averaging 15 cm deep in soft/loose soil complete all as specified and directed.

Excavation over areas, not exceeding 1.5m deep and getting out as in soft/loose soil complete all as specified and directed.

Excavation in trenches not exceeding 1.5 m wide and not exceeding 1.5 m in depth for foundation etc. or for shafts, wells, cess pits, manholes, pier holes etc. not exceeding 10 Sqm on plan and not exceeding 1.5 m in depth and getting out as in soft/loose soil complete all as specified and directed.

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exceeding 25 cm as in soft/loose soil complete all as specified and directed.

Removing excavated material (soil) not exceeding 50 m and depositing where directed at a level n. exc. 1.50 m above the starting point complete all as specified and as directed.

Excavating in post holes (or similar holes) each n exc 0.5 cum, getting out, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25cm, watering, and removing surplus soil to a distance n exc 50 m and making good surface complete all as specified and directed

M&L hardcore of broken stones of gauge n exc 63 mm , deposited spreaded , levelled in layers n exc 15 cm thick watered and rammed to true surface complete all as specified and directed.

M& L Cement concrete 1:4:8 Type D 2 using 40 mm graded aggregate ,in foundations, filling and mass concrete complete all as specified and directed

M & L for Plain Cement Concrete 1:3:6 type C-2 (Nominal Mix) using 40 mm graded stone aggregate as in foundation including necessary formwork etc complete all as specified and directed.

M&L cement concrete 1:3:6 Type C1 (using 20 mm graded aggregate) in, in lintels upto 1.5m clear span, cills, steps; seismic and other similar bands, plinth courses, string courses, lacing courses, parapets and railings upto 60 cm in height, copings, kneelers, apex stones, bed plates, kerbs not provided for in Item 04028, water troughs and the like including weathering, slightly rounded or chamfered angles and throating, as directedcomplete all as specified and directed

M&L cement concrete 1:2:4 Type B1 (using 20 mm graded aggregate) as in cills, steps; seismic and other similar bands, plinth courses, copings and the like including weathering, slightly rounded or chamfered angles and throating, complete all as specified and directed

M&L cement concrete 1:2:4 Type B2 (using 40 mm graded aggregate) as in walls or retaining walls, any thickness, size or shape including pilasters, buttresses columns, pillars, boundary pillars and posts (including caps and bases)complete all as specified and directed

M & L for 100 mm Plain Cement Concrete 1:4:8 type D-2 (Nominal Mix) using 40 mm graded stone aggregate as in sub base flooring etc complete all as specified and directed.

M&L for 100mm thick Cement concrete 1:3:6 type-C2 as in subbase, floor and paving etc.complete all as specified and directed

M&L for 75mm thick Cement concrete 1:2:4 type-B-1 (using 20mm graded stone aggregate) as in sub base, floor and paving finisging cement concrete surface even and smooth etc.complete all as specified and directed

M&L for 40mm thick Cement concrete 1:2:4 type-B1 as in flooring etc. complete all as specified and directed

M &L Brickwork with subclass 'B' old size bricks, straright or corved on plan exc 6m mean radius built in Cement mortar 1:4 complete all as specified and directed

M&L 100mm thick soling spread thickness with broken boulders or quarried stones inter stices, filled (90mm to 63mm size of boulders) surface formed and rolled and consolidated to required gradient and camber complete all as specified and directed.

M&L soling with broken boulders or quarried stones not exc 15cm thickness and rolled and consolidated to required gradient and camber complete all as specified and directed.

M &L Stone sett flooring with stone setts of size 200 to 250mm long, 150 to 200mm wide and 150mm deep and sides dressed; bedded in cement mortar 1:3, joints 20mm thick; grouted in cement mortar 1:2 with an admixture of metallic floor hardner 5% by weight of cement and struck flush complete all as specified and directed.

M&L Mild steel bars 10mm dia and over, cut length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips conforming to Gd-I, IS-432 (Part-I) complete all as specified and directed.

S&F Plates (plain or chequered) channels, square cut or notched (ordinary and counter sunk) forming holes, without any attachment of quality Á'Fe 410-W (Gde E-250) complete all as specified and directed

S&F Hand rails, half round or other stock section or core for wooden hand-rail straight portion, drilled and countersunk for balusters running bars, for doors, balusters, nosing to steps including embeding in concrete and screwing etc. wind ties for roof including securing bolts; posts and struts in fencing including cutting tops to shape as directed, drilling holes, notching for wire, etc.; flat iron fillets (for securing wire mesh etc.) including all necessary drilling, bolting or riveting, etc., and similar work conforming to Fe-290 Gde E-165 complete all as specified and directed

S&F framed work with ornamental and inticate design frame work such as grills gratings, etc., with ends of bars shouldered and/ or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed baluster; walk ways; railings; framed work or water tanks and similar work conforming to Fe 290 gde E 165 complete all as specified and directed

M & L Roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc.complete all as specified and as direct

S&F Bands, straps, supports or stays for rainwater, ventilating pipes, including bolts, if required: hooks (stay), heavy, for large gates; hook and pintle hinges: large hasps and staples; chains; hand made sliding bolts; clamps; hold fasts; wall ties; hooks for hanging fans; plain angle cleats for securing purlins to wood trusses or rafters; knee piece inserts; two way and three way straps, plate washers and similar small articles conforming to Fe-290 Gde-E-165 complete all as specified and directed

S&F Framed work as in doors or gates of angle or other section with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering. Doors, etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails and guides) and hanging; also fastening and fixing conforming to grade Fe-410-W or E -250 quality A complete all as specified and directed

S&F Galvanised. 2 strand, steel barbed wire 2.24mm dia barbed with 2mm dia barbs at 75mm spacings and straining and fixing to any type of standard rails straining bolts, including, securing or tying at crossings with and provision of galvanised mild steel wire, staples or steel pins, etc. as directed (each line wire to be measured) complete all as specified and directed

S&F Mild steel screw bolts (machine made) with hexagonal or square heads at one end and screwed the other, or screwed both ends, each screwed end to be fitted with washers and one hexagonal or square nut, exc 5cm but n exc 10 cm long complete all as specified and directed

M & L for 1mm thick Mild steel, plain, black sheet in wall cladding, steel gates and similar work, cut to size, holes punched; including round headed screws, clout nails or rivets and fixed to wood or steel framing with plain 40 mm lap joints with riveted or welded seams, including bending or turning up, mitred angles, etc. as required complete all as specified and directed.

Supply only Chain link MS galvanised fencing, any size or type complete all as specified and directed

Fixing only chain link fencing including line wires, any mesh, size and type to any type of standards, rails, straining bolts, etc. including provission of binding wire complete all as specified and directed

M&L Painting two coats of synthetic enamel paint on steel and iron surfaces of any description over 10 cm in width or girth including preparation and one coat of red oxide primer complete all as specified and directed

Material and labour for two Coats of Cement Base Paint over a coat of alkali resistant primer including preparation of newly plastered surfaces of wall complete all as specified and directed

M&L rendering 15 mm thick in cement mortar 1:4 on brick work or concrete surface of walls finished even and smooth and without using extra cement complete all as specified and directed

M&L Pre- painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and directed

M&L Plain, galvanised, 0.63mm thick mild steel sheeting, in ridges, hips, valley gutters, drip and straight flashings (length and girth as fixed) with grade of zinc coating 275 complete all as specified and directed

M&L forming construction joint 30mm deep x 10mm wide filled with sealing compound Grade A complete all as specified and directed

M&L forming expansion joint 20mm thick filled with performed bituminous filler and to 30 mm primed and sealed with sealing compound Grade A of 75 mm slab thickness complete all as specified and directed

M&L forming construction joint(dummy) 65mm deep x 10mm wide filled with sealing compound Grade A complete all as specified and directed

Dismantling posts or struts (wood, steel or R.C.C.) any section, including taking out embedded portion in concrete and making good disturbed ground complete all as specified and directed

Dismantling fencing wire mesh, any type complete all as specified and directed

Supply,installation,testing and commissioning of silent Diesel Engine driven Generating set ( engine as per IS:10001/10002 and alternator as per IS: 13364) complete with RCC foundation as per manufactuer design 450mm above ground level ,AMF panel with necessary protection & meters including sound proof canopy of capacity 250 KVA (after considering derating factor at Leimakhong ),415 volts,3 phase,4 wire ,50Hz , 0.8 power factor (lagging) RPM-1500 including following:- (A). Engine :- Diesel engine prime mover of suitable BHP after considering derating factor for altitude and temprature at Liemakhong to drive 250 KVA alternator with electronic governor with the following:- (i) Fuel level indicator (ii) Fuel tank capacity not less than 80 liter or more manufactures recommendation (iii) Fuel inlet arrangement iron,outside the acoustic enclouser with locking arrangement (iv) Exhaust fan manifold and residential type silencer (v) Continuous 10% overload capacity in every 12 Hrs running (vi) Self starting with and including 24 V maintenance free battery including charging circuit (vii) Radiator with first fill of coolant (viii) Turbo charger with continuous duty rating (ix) First fill of lubricant oil (x) Coolant temp gauge ,Lubricant oil pressure gauge,Tacho-cum-hour meter (xi) Engine spare parts list and maintenance manual-03 coppies.

ITEM NO 43 CONT..... (D) Base Frame :- Sturdy robust MS frame duly bolted,coupled aligned,tested and housed within acoustic enclouser with anti-vibration pad. (E) Acoustic Enclouser :- It shoud be compact,modular construction and approved by ARAI (nodel agency of CPCB) with the following:- Overall noise level less than 75 'dBmeasured at 1 mtr distance in free field condition , Inside illumination be 2Nos1x18W LED FTL fitting or as per manufacturers design. Note: DG set shall be provided as per manufacurer recommendation and cost of testing including arrangement of artificial load upto 125% of rated capacity ,temporary arrangement of connecting cables, decimal meter and cost of idel & testing material shall deemed to be included in the above quoted rate.

Supply,installation,testing and commissioning of silent Diesel Engine driven Generating set Trolly mounted ( engine as per IS:10001/10002 and alternator as per IS: 13364) complete AMF panel and necessary protection & meters including sound proof canopy of capacity 200 KVA (after considering derating factor at Leimakhong ),415 volts,3 phase,4 wire ,50Hz , 0.8 power factor (lagging) 1500 RPM including following:- (A). Engine :- Diesel engine prime mover of suitable BHP after considering derating factor for altitude and temprature at Liemakhong to drive 200 KVA alternator with electronic governor with the following:- (i) Fuel level indicator (ii) Fuel tank capacity not less than 80 liter or more manufactures recommendation (iii) Fuel inlet arrangement iron,outside the acoustic enclouser with locking arrangement (iv) Exhaust fan manifold and residential type silencer (v) Continuous 10% overload capacity in every 12 Hrs running (vi) Self starting with and including 24 V maintenance free battery including charging circuit (vii) Radiator with first fill of coolant (viii) Turbo charger with continuous duty rating (ix) First fill of lubricant oil (x) Coolant temp gauge ,Lubricant oil pressure gauge,Tacho-cum-hour meter (xi) Engine spare parts list and maintenance manual-03 coppies. (B). Alternator :- Standard design alternator rated at 200KVA,160KW at 0.8 PF(lag) ,415V, 3 - phase 4 - wire ,50 Hz, 1500 RPM,copper wound with the following :- (i) self regulated brushless self excitation, (ii) Automatic voltage regulator with band of voltage regulation of + 2.5% of rated voltage, (iii) Continuous 10% over load capacity in every 12 Hrs running, (iv) Frequency regulation + 1% ,(v) Upgradable to add features for synchronous run

ITEM NO 46 CONT.... Note: DG set shall be provided as per manufacurer recommendation and cost of testing including arrangement of artificial load upto 125% of rated capacity ,temporary arrangement of connecting cables,decimal meter and cost of idel & testing material shall deemed to be included in the above quoted rate.

Supply, laying ,jointing connecting XLPE insulated heavy duty cables with aluminium conductor ,conductor, 1100 volts grade, cross sectional are 300 sq mm 3.5 core laid in trenches/on poles/wall in ducts/passing through pipes and including necessay cable lugs,bolts,nuts and washers complete all as specified and directed.

Supply of heavy duty trolly of mild steel with four wheels , pneumatic with tubeless tyre, front wheels to be made moveable co-axial type, 450mm ground clearance, toeing arrangement for Eicher Vehical, size of trolley as per OEM design of 200 KVA DG set suitable to carry a load upto 7.5 tonnes alongwith 600mm outer guard shall be made of chain link of aperture 25mm x 25mm with MS post & 600mm spacing between DG set and outer guard and over head shed, extra space for LT cable, earthing connection suitable for body complete all as specified and directed by Engr-in-Charge. Note: Trolley design to be got approved by vendors from Accepting Officer.

Earthing complete with galvanised steel earth plate electrode 600x600x6mm thick buried directly in ground ( earth pit not less than 2.5 metres deep below ground level with top edge of the plate not less than 1.5 metres below normal ground level, connected to galvanised iron strip 25x4 mm by means bolts,nuts,chek nuts and washer of galvanised iron or steel and other end connected with to DG set etc as directed including funnel , made of 20 mm dia GI Pipe (Med grade) for watering, 40 mm dia GI Pipe light grade for protection ,wire messh charcoal of cold dust and common salt in alternate layer all around the earth electrode compacted thickness 15cm with concrete pit in PCC 1:3:6 type C1 50mm thick pre cast RCC 1:2:4 type B1with 8mm dia cover slab set in CM (1:4) re-enforcement with 8mm dia deformed bars @ 15cm C/C and suitable handle of 10mm dia MS round bars, including earth work as required complete all as shown in electrical plate No.5 schedule part-I and testing complete all as specified

Supply ,laying, jointing connecting HT XLPE Cable, insulated, screened, PVC bedded, Galvanised Steel Strip or Wire armoured, Electic Power Cable (heavy duty) with Aluminium Conductor, conforming to IS:7098 , 11 KV, cross-sectional area 95 Sqmm 3 Core, laid in Pipe/ Ducts/ Trenches/ under Floor/under Road including Testing, complete all as specified and as directed.

Supply and fix cable jointing kit for 11 KV (earthed)grade cable for indoor termination cold shrink type joint complete with jointing material and accessories suitable for 3 core XLPE, armoured, aluminium conductor cable of size 95 sqmm. complete all as specified and directed.

Supply and fix cable jointing kit for 11 KV(earthed) grade cable for straight through cold shrink type joint complete with jointing material and accessories suitable for 3 core XLPE, armoured, aluminium conductor cable of size 95 Sqmm, complete all as specified and directed.

Supply and fix cable jointing kit for 11 KV(earthed) grade cable for out door termination cold shrink type joint complete with jointing material and accessories suitable for 3 core XLPE, armoured, aluminium conductor cable of size 95 Sqmm, complete all as specified and directed.

Supply and installation, testing and commisioning of indoor type VCB panel boards with 02 incomers(with CT/PT) +01 Bus coupler(VCB without CT/PT) including of provision for out going cables, motorised as well as manually charged fully interlocked, horizontal draw -out type with ingress protection rating IP4X-floor mounted, 11 KA 3 Ph, 50 Hz AC supply system, indoor metal clad type factory bulit fabricated out of 2mm thick CRCA sheet steel and and extensible on either sides , free standing power coated finished ,floor mounted type with track mounted VCB vertical/ horizontal isolation, aluminium Busbar capacity not less than 800 Amps, prewired for controller & accessories using copper conductor, Provn for cable entry/ outgoing system complete and comprising of the following:- (i) HT Vacuum circuit breaker :- Switch gear of working voltage 11 KV current rating 630 Amps 3 Ph 50 Hz AC Supply Breaking Capacity 25 KA for 3 Seconds at rated voltage making capacity 65.75 KA at rated voltage. impulse withstand voltage 75 Vp min power frequncy withstand voltage 28 KV, closing & shunt trip coils suitable for 110 V DC etc from power pack of suitable capacity. (ii) Numerical relay REJ601 or equivalent model for E/F, O/L and short circuit fault including antipumping operation and accordingly trip coil operation ( Make:- Seimen/alsto/ABB) (iii) Alarm annunciator for DC supply fail/ trip

ITEM NO 56 CONT..... (iv) Multifunction meters 3 ph, 4 wire CL-1 with RS485 port (digital flush mounted type) to indicate various parameters incl current voltage KVA, demand KW , PF , Frequncy, etc (v) LED indicator lamp for RYB phase, healthy, breaker ON/OFF, trip circuit healthy, Spring charged breaker control switch (vi) Push button for check trip healthy& emergency trip, (vii) Switch for closing / tripping of VCB (viii) PTs (3P/3L Drawout, 11KV/RT3/110V/RT3core1-50 VA CL-1) shall be provided on the incoming side and the PT shall be mounted independently on a seperate drawout type trolly with HT Fuses. (xi) CTs with Ratio 200/100/5-5 Amps (Accuracy class 1, 10 VA for metering 5 P10 , 15 VA for protection ) (x) Inbuilt power powe pack of suitable with I/P voltage 220 V AC & O/P voltage 110V DC for protection relay operation with capacity calculation details with min warranty of 2 years (xi) Other standard accesories shall be of reputed make as specifed make as specified by manufactrurer Note: (a) CT and PT to be provided in incoming VCBs only (b) VCB and HT Panel should be of the same make

Supply and installation, testing and commisioning of indoor type VCB panel boards ( 01 incomers -(with CT/PT ) 01 outgoing cable) motorised as well as manually charged fully interlocked, horizontal draw -out type with ingress protection rating IP4X-floor mounted, 11 KA 3 Ph, 50 Hz AC supply system, indoor metal clad type factory bulit fabricated out of 2mm thick CRCA sheet steel and and extensible on either sides , free standing power coated finished ,floor mounted type with track mounted VCB vertical/ horizontal isolation, aluminium Busbar capacity not less than 800 Amps, prewired for controller & accessories using copper conductor, Provn for cable entry/ outgoing system complete and comprising of the following:- (i) HT Vacuum circuit breaker :- Switch gear of working voltage 11 KV current rating 630 Amps 3 Ph 50 Hz AC Supply Breaking Capacity 25 KA for 3 Seconds at rated voltage making capacity 65.75 KA at rated voltage. impulse withstand voltage 75 Vp min power frequncy withstand voltage 28 KV, closing & shunt trip coils suitable for 110 V DC etc from power pack of suitable capacity. (ii) Numerical relay REJ601 or equivalent model for E/F, O/L and short circuit fault including antipumping operation and accordingly trip coil operation ( Make:- Seimen/alsto/ABB) (iii) Alarm annunciator for DC supply fail/ trip

ITEM NO 58 CONT... (iv) Multifunction meters 3 ph, 4 wire CL-1 with RS485 port (digital flush mounted type) to indicate various parameters incl current voltage KVA, demand KW , PF , Frequncy, etc (v) LED indicator lamp for RYB phase, healthy, breaker ON/OFF, trip circuit healthy, Spring charged breaker control switch (vi) Push button for check trip healthy& emergency trip, (vii) Switch for closing / tripping of VCB (viii) PTs (3P/3L Drawout, 11KV/RT3/110V/RT3core1-50 VA CL-1) shall be provided on the incoming side and the PT shall be mounted independently on a seperate drawout type trolly with HT Fuses. (xi) CTs with Ratio 200/100/5-5 Amps (Accuracy class 1, 10 VA for metering 5 P10 , 15 VA for protection ) (x) Inbuilt power powe pack of suitable with I/P voltage 220 V AC & O/P voltage 110V DC for protection relay operation with capacity calculation details with min warranty of 2 years (xi) Other standard accesories shall be of reputed make as specifed make as specified by manufactrurer Note: (a) CT and PT to be provided in incoming VCBs only (b) VCB and HT Panel should be of the same make

Supply and installation, testing and commisioning of indoor type VCB panel boards 01 incomers (with CT/PT )with incoming and provision of for 02 outgoing cables motorised as well as manually charged fully interlocked, horizontal draw -out type with ingress protection rating IP4X-floor mounted, 11 KA 3 Ph, 50 Hz AC supply system, indoor metal clad type factory bulit fabricated out of 2mm thick CRCA sheet steel and and extensible on either sides , free standing power coated finished ,floor mounted type with track mounted VCB vertical/ horizontal isolation, aluminium Busbar capacity not less than 800 Amps, prewired for controller & accessories using copper conductor, Provn for cable entry/ outgoing system complete and comprising of the following:- (i) HT Vacuum circuit breaker :- Switch gear of working voltage 11 KV current rating 630 Amps 3 Ph 50 Hz AC Supply Breaking Capacity 25 KA for 3 Seconds at rated voltage making capacity 65.75 KA at rated voltage. impulse withstand voltage 75 Vp min power frequncy withstand voltage 28 KV, closing & shunt trip coils suitable for 110 V DC etc from power pack of suitable capacity. (ii) Numerical relay REJ601 or equivalent model for E/F, O/L and short circuit fault including antipumping operation and accordingly trip coil operation ( Make:- Seimen/alsto/ABB) (iii) Alarm annunciator for DC supply fail/ trip (iv) Multifunction meters 3 ph, 4 wire CL-1 with RS485 port (digital flush mounted type) to indicate various parameters incl current voltage KVA, demand KW , PF , Frequncy, etc

ITEM NO 60 CONT.... (v) LED indicator lamp for RYB phase, healthy, breaker ON/OFF, trip circuit healthy, Spring charged breaker control switch (vi) Push button for check trip healthy& emergency trip, (vii) Switch for closing / tripping of VCB (viii) PTs (3P/3L Drawout, 11KV/RT3/110V/RT3core1-50 VA CL-1) shall be provided on the incoming side and the PT shall be mounted independently on a seperate drawout type trolly with HT Fuses. (ix) CTs with Ratio 200/100/5-5 Amps (Accuracy class 1, 10 VA for metering 5 P10 , 15 VA for protection ) (x) Inbuilt power powe pack of suitable with I/P voltage 220 V AC & O/P voltage 110V DC for protection relay operation with capacity calculation details with min warranty of 2 years (xi) Other standard accesories shall be of reputed make as specifed make as specified by manufactrurer Note: (a) CT and PT to be provided in incoming VCBs only (b) VCB and HT Panel should be of the same make NOTE FOR ITEM NO 56,58 and 60 OF SCH Á'/BOQ (i) Entire VCB including switch gears shall be manufactured by OEM of original make only, NOT assembled through designated assemblers or ancillary units. (ii) Taking out, refixing, reassembling/realignment of existing VCB and making good disturbed surface to match with existing shall be deemed to be included in unit rates quoted. (iii) Test report of VCB shall be submitted in original.

S&F Switch Air Break Gang Operated for 11 KV grade, triple pole vertically mounted on insulator and fitted on steel frame , current rating 200 Amps, mechanically operated mechanism from Ground level consisting of operating rod of GI Pipe 25mm bore (dia) ‘light grade’ of suitable length worked from ground level and with locking arrangement mild steel flat iron clamp 50x6mm including complete all as specified and as directed

S&F Switch Air Break Gang Operated for 11 KV grade, triple pole vertically mounted on insulator and fitted on steel frame , current rating 400 Amps, mechanically operated mechanism from Ground level consisting of operating rod of GI Pipe 25mm bore (dia) ‘light grade’ of suitable length worked from ground level and with locking arrangement mild steel flat iron clamp 50x6mm including complete all as specified and as directed

Supply & Erecting Steel Tubular Swaged Pole Type 410-SP-55 (11.0 Metre long) including Cast Iron Base Plate, Finial Taper Plug, Cap, Mild Steel Bolts, Nuts, Screws including applying two coats of Black Bituminous Paint Internally and Externally from bottom End of Pole upto PCC Coping and applying with two coats of Aluminium Painting over a coat of Aluminium Primer (Externally from Top of Coping) including writing MES Pole No.with synthetic Enamel Paint (First Grade/quality), complete all as specified and as directed.

S&F metal oxide type, distribution class, discharge capacity 5 KA for 11KV confirming to IS-3070 complete all as specified all as specified and as directed

M & L for earthing complete with galvanised steel earth plate electrode 600 x 600 x 6.3mm, thick buried directly in ground ( earth pit not less than 2.25 Metre deep below the Ground Level ) with top edge of earth Plate not less than 1.50 Metre deep below normal ground level , connected to Galvanised iron 32x6 mm strip, by means of bolts,nuts ,check nuts,bolts and washers, made of 20 mm dia GI Pipe (Med grade) for watering, 40 mm dia GI Pipe light grade for protection of earth lead wire,including necessary earth work in any type of soil , PCC (1:3:6) Type C1 Concrrete pit RCC (1:1.5:3) Type A1 Precast cover (54x54x5Cm) duly reinforced with including 8mm Dia TMT Bar @ 150 mm c/c both ways lifting handle made of 8mm dia TMT Bar embeded in precast cover slab complete as shown in electrical Plate No 3 of SSR Part-I including testing on completion complete all as specified and as directed.

Supply, installation, testing and commissioning oil naturally cooled,3 Phase,50 Hz copper double wound out door application,500 KVA ,Servo controlled /manual automatic voltage regulator suitable for input voltage variation 9 KV to 12 KV( Balanced type) ,3 Phase and 50 Hz and 11 KV+1% output Voltage as required and as per specification voltagge stabilized at 11 KV capacity 500 KVA complete all as specified and directed

M&L for Insulating mat thickness 2.5mm, shock proof, flame re tardant class-B suitable for 11KV confriming to IS 16652-2006 of IEC-61111 all as specified and directed

Dismantling of 03 Nos existing VCBs/OCBs of any capacity including cables GODs etc and preparation of disturbed surface area wherever is required complete as per direction of Engineer-in-Charge. Note:- 03 Nos OCB to be deposited in MES store yard.

M&L Cross-arms, Bracings, Supports, Clamps and Back Plates fabricated from Structural Steel Sections including Nuts, Bolts, Washer, welding, bending cold or hot, drilling holes for Bolts, in any shape or size as indicated/ directed and inclusive of one coat of Aluminium Primer one Under Coat and One Finishing Coat of Aluminium Paint, complete all as specified and as directed.

M&L for Aluminium Conductor Steel Reinforced (ACSR) (sizes as ordered) with permissible Sags and providing Jumper, etc., fixing on Electric Poles and binding to Insulators with Aluminium Binding Wire as in OH Conductors including stringing, tightening, etc., complete all as specified and as directed.

M&L Danger Notice Plate of 1.6 mm thick Mild Steel Sheet, vitreous enamelled white, with Letters, Figures and Conventional Skull and Bones in Signal Red colour and fixed with MS Clamps Bolt and Nuts of approved size, for HT 25x20 Cm size , complete all as specified and as directed .

M&L for Unreinforced Pre-cast Concrete Cable Cover, Class HV type 1flat of size 300x180x40mm with minimum average breaking load 350 Kg, as per IS-5820:1970, complete all as specified and as directed.

S&F Galvanised Iron Pipe 80mm bore (dia), Light grade as in protection of UG Cable laid in Trenches, complete all as specified and as directed.

Supply and fixing as in replacement Anti-climbing device; spikes type fabricated out of M.S. bars (round, square and flat) including nuts,bolts, washers and welding in two halves made to shape to suit thecross section of the pole complete all as specified and as directed.

Supply, spreading,leveling,well ramming including watering and consolidration sand cushioning under ground cable for protection 8 cm bebfore laying and 15 cm after laying with dry fine river sand complete all as specified and directed.

Boring holes horizontally under road without damaging the surface of road (minimum 1.0 mtr below the road surface with the help of GI tubing not exc. 100mm bore (dia) for passing of UG Cable, complete all as specified and as directed.

M&L for HT 11 KV cable route indicator made of angle iron 40x40x6 mm 1 mtr long and fix on the top angle iron MS sheet 3.15 mm thick round shape including pre-cast reinforced Cement Concrete 1:2:4 (20mm graded aggregate) embossing 'DANGER/HT11KV cable/MES' on both sides and painted letters with approved Colour, burried in ground for a depth of 45 Cm including necessary Earth Work, complete all as specified and as directed.

M&L for ducts for laying of power cables along with MS covers all as specified and directed (provisionof Sum)

M/S Satish Chand Agarwal

APPLE CONSTRUCTION