SHC Siwana

Amount

Dismantling Brick Wrok, Tile Masonry or Tile Lining and Tile Terracing (HSR 8.5) (b) In cement

Dismantling brick or flagged stone slab flooring including concrete base. (HSR 8.27)

Cement concrete 1:8:16 with brick ballast 40 mm nominal size in foundation and plinth (HSR 10.26)

Providing and laying 80 mm thick ISI Marked interlocking paver blocks conforming to IS 15658: 2006 / IRC: SP:63-2004 of all shapes and colours of design mix cement M-40 over a bed of 30 mm thick fine sand complete in all respect. (HSR 10.159)

Terracing consisting of tiles 22.86 cm X 11.43 cm X 3.81 cm laid over 87.50 mm mud filling on a layer of 25mm mud mud plaster and an other layer of mud mortar for laying the tiles, including two coats of bitumen laid hot at 1.65 Kg per sqm on top of R.C.C. slab including grouting with cement sand mortar 1:3 and top surface to be left clean etc. (HSR 13.13)

Precast chequered tiles of 20 mm thickness in ordinary grey ceent without chips laid on 20 mm thick bed of cement coarse sand mortar 1:3 with neat cement slurry between joints and over the base of floors, treads of steps and landings. (HSR 14.45)

Kotah stone flooring minimum 25 mm thick, in any pattern as specified over 20 mm thick base of cement coarse sand mortar 1:3 laid and jointed with neat cement slurry mixed with pigment to match the shade of stone including rubbing and polishing. (HSR 14.62)

Kotah stone 20 mm thick in skirting risers of steps, dados, pillars and wall facing (lining) in any pattern as specified laid on 12 mm thick cment coarse sand plaster 1:3 laid and jointed with neat cement slurry, mixed with pigment to match the shade of stone including rubbing and polishing including labour for fixing cramps, dowels and pins etc. (HSR 14.66)

12 mm thick cement plaster 1:4 (HSR 15.5)

15mm Thick Cement Plaster 1:6 on the rough side of single or half brick wall. (HSR 15.12).

10 mm thick cement plaster 1:4 (HSR 15.52)

Preparation of ply wood surface for painting including sand papering the surface and applying filling with approved quality filler consisting of white lead, linseed oil, varnish and chalk mitti including finishing the surface to required finish complete. (HSR 16.1) (T.R.)

Applying pink prier or aluminium priming coat on wood work including preparation of surface, knotting and stopping, etc. (HSR 16.2) (T.R.)

Painting two coats excluding priming coat with synthetic enamel paint in all shades of new wood work or metallic or plastered or concrete surfaces to give an even shade. (HSR 16.3) (T.R.)

Distempering with washable oil bound distemper (of approved manufacture) two coats excluding priming coat on new work. (HSR 16.57) (T.R.)

Providing two coat of exterior acrylic emulsion paint (HSR 16.79) ( b) 1st quality) (T.R.)

Providing and applying two coats white cement based putty over plastered surface and grinding the surface smooth with sand paper to get an even and smooth finish including cost and carriage of all material, labour charges, scaffolding, sundries etc. complete (J.K. / Birla make) (HSR 16.81) (T.R.)

Factory-manufactured wire gauze door and window shutters of commercial hard wood such as hollock, champ, chikrassy and chaplash, etc. (non coniferous timber other teak, conforming to I.S. specification No.1003, kiln seasoned) with 100 mm wide vertical styles, 150 mm wide lock rail 200 mm wide bottom rail, and wire gauze of 140 G or 120 G designation including cost of iron hinges, screws, chock/cleats, stops nails etc., complete fixed in position (excluding the cost of any fittings, other than specified above, but including labour for fixing the same in position). (HSR 17.92) (i) 30 mm thick

Factory manufactured solid flush door shutters, with block board core as per I.S. No.1659-1969 bonded with water proof type phenol formaldehyde synthetic resin, hot-pressed, conforming to I.S. 2202 part I and II , fixed in position, including iron hinges, screws, chocks/cleats and stops, etc., (excluding the cost of any fittings other than specified above, but including labour for fixing the same in position) (HSR 17.93) (a) Commercial veneering with vertical grains or cross bands and face veneer on both sides commercial facing with laminated core and lipped edges:- (iii) 35 mm thick

Pressed steel sheet frames (chowkats), consisting of 2 mm thick steel sheet of the specified section, including iron lugs (hold fasts), iron hinges, conforming to P.W.D. specifications, including bolts for fixing stops, locknotch, provision for receiving tower bolts, and finished with one coat of ready-mixed paint red lead non-setting primer, of approved quality, fixed in position including the cost of cement concrete 1:3:6 for filling in the frame, and cement concrete 1:3:6 for lugs complete. (HSR 18.34) (d) Door and window frame of size 114 mm X 50 mm with 35 mm wide double rebate.

Providing & Fixing in position best Indian make (to the approval of the Engineer-in-charge). Indian type orissa or orya water water closet suite for sinking into floor, with raised foot treats complete with 100 mm H.C.I.'P' trap with or without vent as required and all other necessary fitting as fully described in item No. 30.1 (above) (HSR 30.2) (a) Size 580 mm (i) White

Providing and fixing in position best indian make (as approved by the engineer-in-charge European type water closet suite, syphonic type consisting of- (i) VITREOUS CHINAWARE SYPHONIC SUITE WITH 15 LITRES CAPACITY MATCHING CHINAWARE CISTERN and all internal brass fittings COMPLETE WITH ‘P’ or ‘S’ TRAP with or without vent; (as approved by the Engineer-in-charge). (ii) One piece SEAT AND LID IN HOLLOW BLACK OR WHITE PLASTIC fitted with chromium plated hinges and rubber buffers, (to the approval of the Engineer-in-charge) COMPLETE in all respects INCLUDING CUTTING AND MAKING GOOD THE WALLS AND FLOORS. (HSR 30.5) (a) Single trap Syphonic W.C. Suite (ii) Single colour

EXTRA OVER item Nos. 30.1 to 30.4 and 30.6 FOR PROVIDING AND FIXING 15 LITRES CAPACITY LOW LEVEL VITREIOUS CHINA WARE CISTERN complete with flush bend all other necessary fittings instead of C.I. high level cistern complete with fittings. (HSR 30.12) (i) White

EXTRA OVER item nos. 30.3 to 30.6 FOR PROVIDING AND FIXING BEST INDIAN MAKE PLASTIC HYGENIC SEAT with lid complete instead of hollow black or white plastic seat and lid. (HSR 30.13) (i) White plastic seat (Solid)

Providing & Fixing in position best indian make (ordinary) lavatory suites consisting of Lavatory in Vitreous Chinaware size as given below (to the approval of the Engineer-in-charge) (HSR 30.41 ) White (v) Size 560 mm X 450 mm with one no. tap

Providing and fixing in position best Indian make towel rails fixed in with rawlslugs embedded in walls with C.P. Brass screws, complete in all respect including cutting and making goods the walls etc (HSR 30.68) (a) 25 mm dia, C.P. Brass adjustable. (i) 750 mm long

Providing and fixing in position glass shelf fixed in with rawl plugs with C.P. Brass screws, complete including cutting and making good the walls etc. (HSR 30.69) (a) With C.P. brass brackets and guard rail (i) 600 mm X 125 mm

Providing and fixing in position best Indian make Soap dish fixed into wall with C.P. brass screws and complete in all respects including cutting and making good the walls etc. (HSR 30.70) (a) C.P.BRASS (i) Soap dish large

Providing & fixing in position best Indian make bevelled edge 5.5 mm thick mirror mounted on absetos sheet ground fixed in postion by means of 4 Nos. chromium plated brass screws and washers over rubbers washers and rawl plug embeded in the wall or chromium plated brass clamps with C.P. brass screws (as required by the engineer-in-charge) complete including cutting and making good the walls etc. (HSR 30.71) (a) Indian Make (i) 600 mm x 450 mm.

Providing and fixing in position 15mm i/d C.P. brass bib cocks of best quality (as required by the Engineer-in-charge). (HSR 30.75) (a) Bib cock long body

Providing and fixing in position C.P. brass stop cocks (as approved by the Engineer-in-charge) (HSR 30.76) (a) 15 MM STOP COCK (ii) Concealed stop cock with flange

Providing and fixing C.P. brass liquid soap container of best quality (as required by the Engineer-in-charge). (HSR 30.77)

Providing and fixing in position best Indian make flexible tube connection (HSR 30.82) (b) C.P. Brass (iii) 15 mm X 450 mm

Providing and fixing HDPE WATER STORAGE TANKS of Sintex, Diplast, O.K. Supreme make with covers/lids marked with IS:12701 on roof top of buildings including cost of hoisting and placing in position, making connections with ilet and outlet pipes, providing over flow and scour provisions with suitable plug on scour pipe including cost of nipples, washers, flanges for connections in tanks complete in all respects to the satisfaction to the Engineer-in-Charge. (Except civil work) (HSR 30.119) 1000 Ltr. Capacity

Providing for laying, jointing, fixing and testing G.I. (Medium class "B" type of Tata & Jindal make) pipe lines and specials tees bends, sockets, elbows etc. inside building and testing etc. complete including cutting threading. Including cost of Special. G.I. specials shall be of Make:- UNIK, TATA, ZOLOTO. (NS) (i) 15 mm internal diameter of pipeline

(ii) 20 mm internal diameter of pipeline

Providing and fixing and jointing union couplings in G.I. and W.I. pipelines. (a) 15 mm internal diameter (N.S.)

(b) 20 mm internal diameter

Providing and laying 150 mm thick (in two layer) Granular Sub Base (GSB) conforming to Table 400.1 Grading-I of MoRT&H 5th edition, mixing in a mechanical mix plant at OMC, carriage of mix material to the site of work, spreading in uniform layer with motor grader on prepared surface and compacting with vibratory power roller to achieve desired density complete as per clause No. 401 table No. 400.2 (grade-I) of MoRT&H specification for road & bridge (5th Revision) of 2013 latest edition as per Clause No. 401. (N.S) Note:-only curst material should be used no local earth/sand shall be used. The material finer than 425 micron shall have zero Plasticity Index (PI). (NS)