GEK-67/2021-22

Amount

Schedule 'A' Section - I

Demolition of cement concrte (un- reinforced) in ground floor and paving n. exc 15 cm thick bleow or above hround level complete all as specified.

Demolition of brick work or stone boulder masonry built in cement mortar complete all as spd and as directed.

Dismantling of RCC shelf other than ground floors and similar suspended works complete all as specified.

Taking down cement plaster of any description on brick wall surfaces etc including raking out joints hacking for key , scrubbing down down with water etc complete all as specified .

Dismantling floor, hearth or wall tiling incl cement mortar bedding (but not backing) and rubbish off the premises complete all as specified.

M&L brick work with sub class 'B' bricks of class designation 10 all as per IS-1077-1992 (minimum compressive strength of brick 100 kg/Sqcm) old size bricks, straight or curved on plan exceeding 6 mtr mean radius built in CM 1:6, complete all as specified & directed.

M&L brick work with sub class 'B' bricks, straight or curved on plan to any radius in half brick thick built in CM 1:4 with sub class 'B' bricks of class designation 10 (minimum compressive strength of brick 100 kg/Sqcm) complete all as specified & directed.

M&L for rendering 10mm thick on brick/stone masonry surfaces or surfaces other than fair face of brick work in CM 1:6, finishing surfaces .complete all as specified.

M&L 5mm thick rendering in CM 1:3 on concrete surface of chajjas or ceiling, finished surfaces complete all as spd.

M&L rendering 15mm thick CM 1:4 on fair face of brick over concrete surface finished surfaces, complete all as spd. (WPC Shall be measured separately).

M&L Vitrified Ceramic tiles 10 mm thick (square/ rectangular) polished ceramic tiles (coloured/dark shade /double charged/ultrachaged) (square/rectangular) area of each tile exc. 0.18 sqm but n. exc. 0.36 sqm as in floors set and jointed in cement slurry and pointed in coloured cement including provision of screed bed 15mm thick in CM (1:6) complete all as spd & as directed.

M&L Non Skid /matt finished ceramic tiles (coloured) 600x600x 7 to 8mm thick (square/rectangular) area of each tile exc. 0.18 sqm but n. exc. 0.38 sqm as in floors set and jointed in cement slurry and pointed in coloured cement including provision of screed bed 15mm thick in CM (1:6) complete all as spd & as directed.

M&L Non Skid ceramic tiles (coloured) 400x400x 7 to 8mm thick (square/rectangular) area of each tile exc. 0.11 sqm but n. exc. 0.18 sqm as in floors set and jointed in cement slurry and pointed in coloured cement including provision of screed bed 15mm thick in CM (1:6) complete all as spd & as directed.

-do- but as on vertical surfaces incl 10mm thick rendering in CM 1:4 -do-(Ser Item No.11.00)

M&L 1st quality, glazed ceramic coloured tiles 350x250x 7mm/450x350x 7mm thick on verticle surface of walls with neat cement slurry @ 3.00 Kg / Sqm incl pointed in white cement with pigment to match the shade of tiles, over and incl scrceed bed 10mm thick 1:4 all on spd .

Demolition stone slabs of any description or thickness in floors, aprons etc laid bedded and pointed in any mortar complete all as specified.

M&L for 20mm thick,black, Granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, win dow-cills, cooking plat forms and like in cement mortar (1:4) including point ing in white cement (1:2) us ing marble dust with admix ture of pigment to match with shade of granite. Note:- (i) The rate of granite stone shall be deemed to incl for full rounded off corner/ edges incl holes for pipe all cutting to make it square or rectangular. (ii) The rate shall also be deemed to incl for cutting and polishing machine and granite polishing to achive the desired granite finish all as spfd.

M & L RCC 1:2:4 type B-1 using 20mm graded stone aggregate as in shelves / slabs and like with and incl use and waste of necessary form work complete all as specified.

M & L MS TMT Bars 10mm dia and over cut to length, bend to shape required, incl cranking, bending, for hooping for columns, hooking ends and binding with and incl MS wire (Annealed) not less than 0.9mm dia or securing with clips complete all as specified.

M & L MS TMT Bars 8 mm dia cut to length, bend to shape required, incl cranking, bending, for hooping for columns, hooking ends and binding with and incl MS wire (Annealed) not less than 0.9mm dia or securing with clips complete all as specified.

Cement concrete type B1 (1:2:4) using 20mm grades stone aggregate as in copings, bed plates, fixing of hold fasts and other similar works and the like incl weathering, slightly rounded or chamfered angles and throating as directed incl use and waste of necessary form work complete all as spd.

Taking down chawkhat or frame with (without taking of shutters from the frames) exc 1.50 sqm but n. exc 4sqm complete all as spd.

–do- but n.exc 1.5 sqm.

Taking down shutters of any description n. exc 1 sqm from chowkhat and removing to or from store as required complete all as specified.

Taking down shutters of any description exc 1 sqm but n.exc 2 sqm from chowkhat and removing to or from store as required complete all as specified.

Taking down shutters of any description exc 1 sqm but n.exc 2 sqm from chowkhat and re-fixing in same opening after re-securing or easening and adjusting including repair of hinge as required complete all as specified.

M&L plain solid straight chawkhats of 2nd class hard wood and frames rebate on the solid rounded or chamfered , put to gather with glue pinned at joints complete all as specifided.

M & L Pressed steel frames for doors of size 125 x 60 mm with one or more rebated incl necessary fixing lugs, hinges, lock, strike plates of 50 x 3mm welded with frame for making arrangement for fixing of door spring etc. complete all as specified.

M & L Pressed steel frames for doors of size 105 x 60 mm with one or more rebated incl necessary fixing lugs, hinges, lock, strike plates etc. complete all as specified.

S& fixed factory made flush shutters shutters 35mm thick of 2nd class hard wood (any number of panels) with solid core construction & block board core and plywood face panels, commercial type on both sides fixed to chowkhat . The size of rail and stile as per IS : 1003 (Part-1), kiln seasoned and chemically pressure teated complete all as spfd.

S& fixed 2nd class hard wood 30mm thick made glazed and skeleton shutters factory made open rebated and prepared to rceieve glass, gauze,etc. (without sash bars), edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass,etc, size of members of shutters as spfd in SSR Part-1, Section 8, clause 8.24 (a) complete all as spfd .

S & F 30mm thick 2nd class hardwood glazed and skeleton shutters, open rebated and prepared to receive glass, gauge, etc. divided into squares, with plain, chamfered or rounded, mitred and rebated sash bars, any numbers, for securing glass, etc.; sizes of members of shutters as specified in SSR Part I, Section 8, clause 8.24 (b); fitted to chowkats , windows, ventilators etc. are provided with stiles and rails as specified in SSR Part I, Section 8 clause 8.24 (b) complete all as specified and as directed by the Engineer-in-Charge

Supply and fix Factory Made Solid PVC Moulded Door Shutters with Particle board Core 28 to 30 mm thick (stiles), with 2,4 or 6 raised panel design with 2mm thick Moulded Prelam PVC Sheet on the front Face & 2mm Prelam PVC sheet on back face, supplying & fixing in frame at site as per specification and drawing in SSR part II on page no 161 complete all as specified and directed.

Suppling & fixing in opening solid PVC door frame of size 50mm x 47mm made out 5mm plain colour PVC sheets re-inforced with MS square tube complete all as spd.

S&F 25mm flush shutters, solid core construction, with block board core and plywood face panells, commercial types on both sides incl teak wood beading alround the shutters as directed by Engr-in-Charge and all as specified.

S&F mild steel framed work as in grills,guard bars etc. with ends of bars shouldered/welded and/or riveted and other simillar works confirming to Fe410-0 or Fe310-0 complete all as spfd.

S & Fixed galvanized mild steel wire cloth 0.56mm fixed nominal dai of wire and avrg widh of aperature 1.18mm and fixed with tinned tacks or galvanised wire staple complete all as spd.

S&F 4mm thick sheet glass, ordinaly quality and glazing with oil putty or secured with wdn beads as required in square n exc 0.5 sqm in each pane

S&F 4mm thick sheet glass, ordinaly quality and glazing with oil putty or secured with wdn beads as required in square exc 0.5 sqm in each pane

Supply and fixing Figured, Pin head glass 4.0 mm thick, fixed to frame of ventilator /window etc including necessary snap beading and rubber gasket required complete all as specified and directed.

M&L 75mm thick plain cement concrete 1:3:6 type C2 using 40mm graded stone aggregate, laid in 1:20 slope as in plinth protection, coping, surface finished even and smooth without using extra cement, with and incl use and waste of necessary form work complete all as spd.

S & F Mild steel butt hinges medium weight , clod rolled, 100mm, ISI marked, complete all as spd .

S & F Mild steel butt hinges medium weight , clod rolled, 50mm, ISI marked, complete all as spd .

S & F Mild steel butt hinges medium weight , clod rolled, 75mm, ISI marked, complete all as spd .

S&F 2nd class hard wood hollock small fittings such as brackets of any type, latch and hinge blocks, door stops and window stops, the like incl all necessary labours articles n. exc 200 cucm each complete all as spfd.

M&L barrel tower bolts aluminium anodised exlruded section of size 200 mm complete all as spd .

S&F 300 mm long aluminium anodised sliding door bolt with hasp, staple (bolt type) and fixing cleap of sheet, cast or extruded sections, bolt not less then 12mm dia with and including a minimum of 6 bolt and nuts ,fixed on plate or staple plate complete all as spd .

S&F aluminium fabricated type extruded handles of size 125 mm complete all as spd .

S&F in repair of 300mm mild steel ordinary rate tail rod pattern door spring incl roller and roller plate complete all as spfd.

Supply and fix Stainless steel curtain rods of 20mm dia including SS holding brackets and Decorative/ornamental Bulbs/cups including taking down the existing rods.

Taking up or down 15 mm dia steel tubing incl connection and removal from site

- Ditto- but 20mm dia

S & F GI tubing medium gde with all fittings fixed to walls or laid in floors 15mm bore complete all as specified.

S & F GI tubing medium gde with all fittings fixed to walls or laid in floors 20mm bore complete all as specified.

Steel tubing and connections cleaning for refixing and refixing old steel tubing and connections in new or in old position (walls ceiling floor etc) of 15mm bore of pipe complete all as specified

Steel tubing and connections cleaning for refixing and refixing old steel tubing and connections in new or in old position (walls ceiling floor etc)of 20mm bore of pipe complete all as specified

S & F in repair 15mm bib tap cast copper alloy chromium plated with crutch or butterfly handle screwed down screwed for iron pipe or for brass ferrule and fixed complete all as specified.

S & F in repair stop valve/Angle cock fancy type cast copper alloy 15mm bore screwed down high pressure chromium plated concealed type complete all as spd.

S & F in repair stop valve cast copper alloy 20mm bore screwed down high pressure with crutch or butterfly handle screwed both ends for iron pipe or for unioin fixed complete all as spd.

S&F in repairs PVC connections 15mm size with PTMT nuts of length 450mm

Dismantling water tanks exc 250 n. exc 500 ltr capacity complete all as specified.

S & F 500 ltr capacity rotational moulded polythene water storage tanks (clyndrical vertical with closed top) hoisted and fixed in position all as spd in SSR Part I.

Dismantling water tanks exc 500 n. exc 1000 ltr capacity complete all as specified.

S & F 1000 ltr capacity rotational moulded polythene water storage tanks (clyndrical vertical with closed top) hoisted and fixed in position all as spd in SSR Part I.

S & F 20mm bore dia ball brass valves, high pressure with polythene float and flynut complete screwed for iron pipes etc, complete all as specified.

S & F in repairs sinks with drainage board made of stainless steel 1mm thick, kitchen or laboratory with plugs, washers and wastes including bedding in cement mortar to draft wall including brackets and connecting union to pipe overall size 915mm x 460mm bowl size 410mm x 330mm x 160mm complete all as specified.

M&L for plastic water closet seat cover white closed pattern withflat bottom mild steel chromium plated or aluminium hinging device fixed in repair complee all as specified and directed.

S&F Vitreous China wash down water closet pan (pedestal pattern), white (excluding fixing bolts,) complete incl making good to floor to match with adjoining surfaces all as directed by Engr-in-Charge

Supply and fix CP toilet paper holder including chromium plated brass screws and wooden/plastic cleats (Minimum weight 190gms).

S&F in repair brass CP hand shower(health faucet),flexible pipe of suitable length fixed to 15mm bore pipe, complete all as spd.

S&F Brass with CP finished,Jet spray with flexible pipe of suitable length fixed to 15mm bore pipe (faucet) complete all as specified.

S & F viterious china squatting span ORISSA Pattern size 580x440mm with integral foot rests, (excl flushing cistern and flush pipe) but with and incl connection to trap, and to flushing pipe anti-syphonage pipe, etc. complete incl provn of lime concrete and making good to floor, in repair complete all as specified and directed.

S&F 10 Ltrs capacity virgin polypropylene cistern, syphonic action type, ISI marked, white at low level complete with PVC bends, flush pipe and making all connections with and incl inlets ball valve float, handle, brackets and making good the disturbed sufaces in CM 1:3 to match with the existing surface, in repair complete all as specified.

S&F Vitreous china wash hand basin white flat back or angle back type size 600mm x 480 mm white & plug , waste pipe and prop stopper but incl cutting for and pinning in ends of brackets or erecting stand fixed, in repair complete all as specified.

Sheet glass shelf assembly consisting of 5.5mm thick sheet glass shelf 12cm wide with chromium plated brackets, bracket guard and railing 60cm long incl screws, in repair complete all as specified.

S & F in repair CP shower rose heavy duty with swivel joints 125 mm dia fixed to 15mm GI pipe complete all as spd.

S & F in repairs soap dish chromium plated of size 160x160x90mm any type, fixed complete all as spd.o plugs with chromium plated brass screws all as specified.

S & F in repairs brass chromium plated tabular towel rail 20mm dia 'D' type 60 cm long between flanges complete all as specified

PCC (1:3:6) type C2 using 40mm graded stone agg as in surface channel / drains.

Extra for forming fair finished drain or channel 30 cm inner girth in cement concrete using extra cement including forms, moulds/stopped ends etc.

Mild Steel works as in bends straps, hold fasts etc, conforming to IS-206202006 (Fe-290), embedded portion duly painted with bituminious paint and sanded, complete all as specified.

Providing cement concrete C 1 (1:3:6) using 20mm grded stone aggregate as in filling of chowkats incl weathering, slightly rounded or chamfered angles and throating as directed incl necessary form work complet all as spd.

Cutting chase, pining in making good to facings where required & pointing in cement mortar1:3 to ends etc or edges of landings, steps cills,sunshades, shelves,lintels,etc and cutting chasesfor concealed water tubing and making good,cutting n.exc. 10cm girth in brick walls all asdirected.

Dismantling of Cast Iron pipe 75mm to 100mm dia complete all as specified.

S&F 110mm dia PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to wall including clamps as required complete all as specified.

S&F 75mm dia PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to wall including clamps as required complete all as specified.

S&F 75mm dia PVC (SWR) floor trap, plain with grating including jointing with solvant cement incl necessary PCC & form work as required complete all as specified.

S&F 75mm dia PVC (SWR) couplers/socket, equal or un equal with oval accesse door including jointing with solvant cement as required complete all as specified.

S&F 75mm dia PVC (SWR) junction double, (double T), equal or un equal with oval accesse door including jointing with solvant cement as required complete all as specified.

S&F 110mm dia PVC (SWR) reducer, single, equal or un equal of any length including jointing with solvant cement as required complete all as specified.

S&F 75mm dia PVC (SWR) vent cowl, single, equal or un equal of any length including jointing with solvant cement as required complete all as specified.

S&F 110mm dia PVC (SWR) "P" trap single, equal or un equal of any length including jointing with solvant cement as required complete all as specified.

S&F 110mm dia PVC (SWR) "S" trap single, equal or un equal of any length including jointing with solvant cement as required complete all as specified.

S&F 75mm dia PVC (SWR) bends with rubber ring joints fixed as required complete all as specified.

S&F 110mm dia PVC (SWR) bends with rubber ring joints fixed as required complete all as specified.

M&L preparation of new or previourly untreated surface of wood or board materials of any description not otherwise described over 10cm in or girth & appyling two coats of synthetic enamal paint over a coat of pink primer complete all as spd .

M&L preparation of old wooden surface of any descreption not otherwise described over 10 cm widtn or gith & appling two coats of sytnetic /varnish paint complete all as spd .

M&L Preparation of old steel surfaces including preparation of surfaces and applying two coats of synthetic enamel paint ,complete all as specified.

M&L Preparation of new steel surfaces including preparation of surfaces and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified.

Complete removal of existing old surfaces applying two coats of oil bound distemper over one coat of wall care putty on walls all as specified and directed by the Engr-in-Charge

M&L for preparation of old decorated plastered / unplastered surfaces of ceiling two coat of white wash on ceiling and AC plain building board surfaces as in ceiling complete all as specified and directed by Engr-in-Charge

M&L for preparation of new decorated plastered / unplastered surfaces of ceiling three coat of white wash on ceiling and AC plain building board surfaces as in ceiling complete all as specified and directed by Engr-in-Charge

M&L for two coats of distemper oil emulsion on wall incl preparation of new surfaces over one coat of primer on wall surface complete all as specified & directed.

Preparation of newly plastered or unplastered or previously untreated surfaces of walls and applying two coats of exterior emulsion/Apex paint complete all as specified.

Preparation of old plastered surfaces of walls and applying one coat of exterior emulsion/Apex paint complete all as specified.

M & L including preparing of new or previously untreated surface NTP/CGI/PGI or other steel roof over one coat of red oxide primer of any type of treatment surfaces applying two coats of synthetic enamel roof paint complete all as specified..

S & F Stainless steel plate rack of size 900mm x 750mm with shelves, hooks and railing to keep plates vertically and horizontly, including necessary fixing arrangement.

Dismantling plain or corrugated steel sheeting any guage thickness incl Nainital pattern as in roof covering complete all as specified.

S & F 0.63 mm thick Galvanised, corrugated mild steel sheeting with two corrugations side lap, fixed with L-type or J-type or cranked hook bolts in lieu of screws, in roofs, walls etc. with grade of zinc coating 275 complete all as specified & as directed.

S & F 0.63 mm thick Plain, galvanised, mild steel sheeting, in ridges, hips, valley gutters, drip and straight flashings (length and girth as fixed) with grade of zinc coating 275 complete all as specified & as directed.

M & L for applying 1 mm thick wall care putty on new surface of walls etc complete all as specified

Dismantling timber scantlings in any position in fillets, rails, posts, rafters , purlins, etc. under 40 sq. cm in section (Unframed work) complete all as specified .

M & L as in repair for plain fillets, square, rectangular or triangular in section, and secured with nails or brads, using IInd class hard-wood clean sawn in sectional area exc 13 sq.cm and not exc 25 sq.cm complete all as specified.

Material & Labour for continuous piano hinges mild steel bright finish width of flap 30mm fixed in repair incl taking out the existing complete all as specified & directed.

Prelaminated particle board 19mm thick, exterior gde prelaminated one side with decorative choice lamination and other side balancing white lamination , fixed as in repair with screws to timber frame comlplete all as spd and directed.

S&F 40mm dia, cupboard knobs fixed with nut, screw and washer of mild steel, bright finished complete all as specified.

S&F Hasp and staple, safety type,of aluminium anodised including bolt to hinge plate and fixed with screws 100 mm size complete all as specified.

Supply only water proofing compouond all as specified as per manafature instruction

S & F in repair concealed stop cock fancy type cast copper alloy 15mm bore screwed down high pressure with fancy type, chromium plated with long shank and cup concealed type complete all as spd.

False ceiling with one layer of 'LaGyp' standard boards manufactured by M/S Lafarge Board Gypsum India Pvt Ltd, at all height and levels. Standard boards of size 1220x1830x12.5mm, standard board to be laid on 'LaGyp' universal channel (web 45 mm premanunfacturers specifications metal comprising of "LaGyp" universal channel (web 45 mm and flange 27mm base metal thickness (BMT) 0.55 mm and length 3660 mm to be used as main channel as well as ceiling channel. "LaGyp" connecting clips, perimeter channel ( Size of web 28 mm, flange 18/30 mm and length 3660 mm, MBT 0.55 mm) and "L" angle (Length 3050 mm BMT 0.55 mm) with finally the board are to be Joined and finished so as to have a flush look which includes filling and finishing the tapered and square edges of the board with "LaGyp" easy joint Gypsum based jointing compound, "LaGyp" paper tape and applying two or more coats of oil bound distemper to give a neat and even finish including preparing the base with primer and necessary scaffolding etc complete all as specified.

Supply and fix Stainless steel peg set of 5 hooks including chromium plated brass screws and wooden/plastic cleats (Minimum weight 190gms).

Supply and fix 15mm bore CP fancy type (wall mixer WBH mixer & sink mixer) for mixing hot & cold water cast copper alloy with capstan handle, screwed down for iron pipe and fixed on wall ,sink or WHB complete all as specified and directed.

Magnetic catches brass body for use in cup boards of kitchen, ward robes etc. fixed as in repairs complete all as specified.

Dismantling boarding, any description, fixed in any position with nails complete all as specified.

Taking down carefully copper/AImn point wiring (Light,Fan/Point Socket or power) (fittings such as switches ceiling roeses, pendent, regulators, sockets etc to be measured & paid seprately) & making good to disturbed surface of walls/floors etc.

M&L point wiring using approved colour coding as per IS with stranded copper conductor single core 1.5 Sqmm (Nominal area), PVC insulated cable in and incl PVC conduit (ISI marked) including cutting chiseling and grouting concealed PVC conduit pipe, tee, elbow and bend etc.and with all connecting accessories incl mild steel sunken boxes suitable for mounting switch/sockets with earth dolly duly painted with two coats of anti corrosive paint over a coat of red oxide primer incl mounting frame over cover plate, covered with 3mm thick plastic laminated sheet, incl PVC insulated copper conductor 1.5 Sqmm (Nominal area) single core PVC cable as earth continuity conductor to common earth and connecting to earth dolly complete all as specified. Note : Switch/sockets shall be measured and paid for separately :-

One light/fan point controlled by one switch

One switch socket outlet 3 pin,5 Amp on the independent board

One switch socket outlet 3 pin,5 Amp on same board

One light point controled by two way switches with cables 1.5 Sqmm size

One bell/buzzer point controlled by one push button on the same board with other switches or independent with cables 1.5 sqmm size

All as per item No 127.00 here-in-before but with 2 single core PVC insulated FRLS and sheathed copper conductor of size 2.5 Sqmm in and including PVC conduit (ISI marked) including cutting chiseling and grouting concealed PVC conduit pipe, tee, elbow and bend etc.and with all connecting accessories with 2.5 Sqmm PVC insulated FRLS copper conductor as earth wire and connecting to common earth dolly for 6 pin 16 Amp socket outlet on the independent board.using 2.5 sqmm copper cable incl PVC insulated copeer conductor 1.5 Sqmm as continued earth wire .

All as per item No 127.00 here-in-before but with 2 single core PVC insulated FRLS and sheathed copper conductor of size 4.0 Sqmm in and including PVC conduit (ISI marked) including cutting chiseling and grouting concealed PVC conduit pipe, tee, elbow and bend etc.and with all connecting accessories with 4.0 Sqmm PVC insulated FRLS copper conductor as earth wire and connecting to common earth dolly for 6 pin 16 Amp socket outlet on the independent board.

S&F bell push, 6 Amps, SP, flush type.

S&F Electric Bell , AC 230 volts, single pole

M& L switch piano, flush type, single pole 2 way 6 Amp,ISI marked

S&F Lamp holder,PVC insulated body, with back plate suitable for batten fitting

M& L switch piano, flush type, single pole 1 way 6 Amp,ISI marked completeall as specified

S&F switch piano flush type, single pole 1 way 16 Amp

M& L socket 5 pin 6 Amp piano flush type,ISI marke.

S&F socket out let 2 in one 6 pin 6 & 16 Amp

S&F ceiling rose, 3 phase/ PVC/ polycorbonate,isolate bady

S & F LED bulb 10 watt.

Supply and fixing Aluminium housing LED 22 Watt inverter batten with inbuilt Li Ion battery for power backup of 2 to 3 hrs complete.

S&F 9 watt led lamp Decorative wall light fixture made up of Polycarbonate , fancy type, made out of Polycorbaonate,suitable for B-22 base holder fixed as in repair complete all as specified and directed.

S&F sleek LED mirror light with diffuser 7/ 9 watt along with all accessories prewired including connecting with copper flexible cable of size 0.7 Sqmm 3 core and all as specified and directed .

S & F Bulkhead luminaire Decorative Energy saving new generation 10W LED IP65 with opal diffuser incl electronics driver & connection with copper flexible cable 3 core complete all as specified and directed.

S & F LED Building security light30 wattLED Inverter RTC inbuilt for AUTOON/AUTO OFF and must have dimming facility from 10 to 100% of rated wattage as peruser defined timeline made pressure die cast housing with individuals LEDs & Lens with modular secondary optics and IP65 protection with electronics driver and copper conductor 3 core of 0.7 sqmm from ceiling rose to security light with Bracket made out of GI light grade pipe of 32 mm dia 1.5 mtr long bend to an angle of 120 degree with fixing arrangements on wall Complete all as in repair.

Supply and fixing wall Mounting LED fitting 9/12 watt 6500K 2 ft Basic all purpose surface and wall mounted led batten with polycarbonate housing & integrated electronic driver complete all as specified and directed.

S&F sheet metal enclosure with double door for DBs conforms to IS:8623.III , IP:43 protection, shrouded neutral bar and cement spill protector, 8 way, 240 Volt SPN

S&F sheet metal enclosure with double door for DBs conforms to IS:8623.III , IP:43 protection, shrouded neutral bar and cement spill protector, 4 way, 415 Volt TPN

S & F MCBs 'B' characteristics, Double pole , 240 V, 32 Amp breaking capacity 10 kA

S & F MCBs 'B' characteristics, Four pole , 415 V,63 Amp breaking capacity 10 kA

S & F MCB B characterstic single pole 5 to 30 Amp, 240 volt breaking capacity 10 kA

M&L for submain wiring with 2 single core PVC insulated FRLS cable 6 Sqmm copper conductor PVC sheathed in and including rigid PVC concealed conduit heavy duty of suitable size incl cutting chiseling of wall and making good to disturbed surface of walls / floor etc with plastering painting etc so as to match with the existing finishes, drawn with 6 Sqmm PVC insulated FRLS copper conductor cable for earth wire fixed with shaddle and connecting to common earth teriminals complete all as specified.

Single pole and Neutral Sheet metal enclosure with a 2 pin and earth plug and socket complete with one single pole MCB 20 Amps.

S & F Non mettalic Electric meter box with single hinged door for 01 No. Single phase meter of size 250 X 200 X 105 mm after disconnecting the supply of electric meter and fixing the electric meter on meter box incl reconnecting the electric supply. Make: Sintex CAt part No. GSMB 2520 or in Equivalent in Hensel / Clipsal

Taking down carefully storage type water heater (Geyser ) of any make of capacity 25/35/50 Ltrs after removing all electrical and water connection from installed position and Refixing in same position Electric storage water heater (vertical type) 25/35/50 litres, with porcelain enamel glass lined inner tank 230 V, AC, Single phase, IS 2082 Marked, 5 Star rating, with 15mm brass non return valve and including connecting fastners not less than 100 mm with suitable nut, bolt & washers grouted in walls with complete masonry work for proper mounting of Geyser fastning bolts etc as directed as site reqmt and making necessary inlet and outlet water & electric connection tested on load including provision of 15 Amp plug top and PVC insulated & PVC sheathed copper conductor cable 4 sqmm 3 core upto 15 Amp plug point and inlet and outlet copper connection complete all as specified and directed.

Supply & Fixing exhaust fan, energy efficent metalic blades heavy duty turbo force of size 300 mm sweep, 900 rpm, AC, 230 volts complete with louvers, shutters, mounting on walls with holding down bolts, nuts, washers with cutting holes into or through stone/brick walls for fixing of 450 mm sweep exhaust fan including making good the cutting and matching the surface with existing surfaces and connection of flexible copper conductor cable three core ceiling rose to fan and testing tacking down old u/s exhaust fan deopsited E/M Sotre complete all as specified. Make:Havells turbo force / Bajaj Supreme

Earthing complete with and including galvanised steel earth plate electrode 60 cmx 60cm x 6 mm thick surrounded by mixture of charcoal and salt in alternate layers , buried directly in ground vertically in a pit of depth not less than 2.25 meter deep below ground level with top as of the plate at a depth of not less than 1.5 mtrs below normal ground level connected to galvanized iron or steel earth lead wire 4.0 mm dia,( NO 8 SWG) by means of bolts ,nuts, check nuts and washers of galvanised iron or steel earth wire protected by galvanised steel pipe 15 mm bore (light grade) and connected to main switch or main control board all as shown in electrical plate No. 3 of SSR - 2009(Pt I) & including necessary excavation and earth work.

The rate also include charcoal and salt in alternate layers, 20 mm bore GI pipe (Light grade ) for watering , protection pipe funnel, wire mesh , PCC 1:2:4 type B1 chamber in cement concrete ,50 mm thick precast RCC M-25 ( Normal mix) cover duly reinforced with XPM (weight not less than 3 kg /sqm ) and CI frame etc , and including provision of test point , connecting to test point and testing on completion etc, complete all as specified. NOTE : The unit rate include earthing lead and protection pipe upto 6.5 metre from top of earth plate.

Supply & laying or fixing or passing through pipe, 1100 volts grade heavy duty cable with PVC insulated aluminium conductor served with an inner sheathing of PVC tape armoured wit galvanised steel wire or tape and overall PVC sheathed 16 Sqmm nominal cross section,4 core ,stranded conductor , in service connections

Excavating in trenches, n.exc 1.5 m wide and n. exc 1.5 m in depth for laying cable , pipe and getting out

Returning , filling in, including spearding, levelling , wateing and well ramming in layers not exc 25 cm

Removing excavated material n exc 50 M and depositing whee directed at a level n exc 1.5 m above the starting point

Supply and fixing in repair of double walled HDPE duct pipe of 63 mm outer dia confirming IS -14930 (Part-II) of approved colour with fittings for cable protection complete all as specified and directed.

Tubes, light grade, galvanised 40 mm dia with all fittings laid in trenches or fixed on walls etc

Amount of credit of Rs. 68912.00 for retrived old material as mentioned in Schedule 'A' section-II of tender document in pdf form, will be deducted offline while acceptence of tender.

R. P. Suppliers and Construction Co.