Loading
Loading…
Loading…
Tender Value
₹2.6 Cr
EMD Value
₹5.2 L
Closing Date
14 Jul 2026, 3:00 pmClosed
No
No
Single Packet System
Normal Tender
No
Not Applicable
Lowest to Highest
60 days
Expenditure
Capital (Works)
Above/Below/Par
SNT WORK
19 conditions · 4 needing a document upload
The tenderer must have minimum average annual contractual turnover of V/N or "V" whichever is less; where V= Advertised value of the tender in crores of Rupees N= Number of years prescribed for completion of work for which bids have been invited.The average annual contractual turnover shall be calculated as an average of 'Total contractual payments" in the previous three financial years, as per the audited balance sheet. However, in case balance sheet of the previous year is yet to be prepared/ audited, the audited balance sheet of the fourth previous year shall be considered for calculating average annual contractual turnover. The tenderers shall submit requisite information as per Annexure-VIB, along with copies of Audited Balance Sheets duly certified by the Chartered Accountant/ Certificate from Chartered Accountant duly supported by Audited Balance Sheet.
The average annual contractual turnover shall be calculated as an average of "total contractual payments" in the previous three financial years. However, in case balance sheet of the previous year is yet to be prepared/ audited, the audited balance sheet of the fourth previous year shall be considered for calculating average annual contractual turnover.
a)The tenderer must have successfully completed or substantially completed any one of the following categories of work(s) during last 07 (seven) years, ending last day of month previous to the one in which tender is invited: (i) Three similar works each costing not less than the amount equal to 30% of advertised value of the tender, or (ii) Two similar works each costing not less than the amount equal to 40% of advertised value of the tender, or (iii) One similar work costing not less than the amount equal to 60% of advertised value of the tender as per Annexure- G of tender booklet.
b) (1) In case of tenders for composite works (e.g. works involving more than one distinct component, such as Civil Engineering works, S&T works, Electrical works, OHE works etc. and in the case of major bridges - substructure, superstructure etc.), tenderer must have successfully completed or substantially completed any one of the following categories of work(s) during last 07 (seven) years, ending last day of month previous to the one in which tender is invited: (i) Three similar works each costing not less than the amount equal to 30% of advertised value of each component of tender, or (ii) Two similar works each costing not less than the amount equal to 40% of advertised value of each component of tender, or (iii) One similar work each costing not less than the amount equal to 60% of advertised value of each component of tender. Note for b(1): Separate completed works of minimum required values shall also be considered for fulfillment of technical eligibility criteria for different components. (b)(2)In such cases, what constitutes a component in a composite work shall be clearly pre-defined with estimated tender cost of it, as part of the tender documents without any ambiguity. (b) (3) To evaluate the technical eligibility of tenderer, only components of work as stipulated in tender documents for evaluation of technical eligibility, shall be considered. The scope of work covered in other remaining components shall be either executed by tenderer himself if he has work experience as mentioned in clause 7 of the Standard General Conditions of Contractor through subcontractor fulfilling the requirements as per clause 7 of the Standard General Conditions of Contract or jointly i.e., partly himself and remaining through subcontractor, with prior approval of Chief Engineer in writing. However, if required in tender documents by way of Special Conditions, a formal agreement duly notarised, legally enforceable in the court of law, shall be executed by the main contractor with the subcontractor for the component(s) of work proposed to be executed by the subcontractor(s), and shall be submitted along with the offer for considering subletting of that scope of work towards fulfilment of technical eligibility. Such subcontractor must fulfill technical eligibility criteria as follows: The subcontractor shall have successfully completed at least one work similar to work proposed for subcontract, costing not less than 35% value of work to be subletted, in last 5 years, ending last day of month previous to the one in which tender is invited through a works contract. Note: for subletting of work costing up to Rs 50 lakh, no previous work experience of subcontractor shall be asked for by the Railway.
In case after award of contract or during execution of work it becomes necessary for contractor to change subcontractor, the same shall be done with subcontractor(s) fulfilling the requirements as per clause 7 of the Standard General Conditions of Contract, with prior approval of Chief Engineer in writing.
Work experience certificate from private individual shall not be considered. However, in addition to work experience certificates issued by any Govt. Organisation, work experience certificate issued by Public listed company having average annual turnover of Rs 500 crore and above in last 3 financial years excluding the current financial year, listed on National Stock Exchange or Bombay Stock Exchange, incorporated/registered at least 5 years prior to the date of closing of tender, shall also be considered provided the work experience certificate has been issued by a person authorized by the Public listed company to issue such certificates.
In case tenderer submits work experience certificate issued by public listed company, the tenderer shall also submit along with work experience certificate, the relevant copy of work order, bill of quantities, bill wise details of payment received duly certified by Chartered Accountant, TDS certificates for all payments received and copy of final/last bill paid by company in support of above work experience certificate.
Definition of Similar Work:- Any signalling work involving design, installation, testing, commissioning of EI or alterations of EI.
31 conditions · 26 needing a document upload
Please furnish list of Works completed in last seven financial years giving Description of Work, Organization for whom executed, approximate value of contract at time of award, Date of award and Date of Completion. Date of actual Start, Actual Completion and Final value of Contract shall also be given. Annexure -G.
Please furnish list of personal, organization available on hand and proposed to be engaged for the subject work.
Documents to be Submitted Along with Tender: (i)The tenderer shall clearly specify whether the tender is submitted on his own (Proprietary Firm) or on behalf of a Partnership Firm / Company /Joint Venture (JV) / Registered Society / Registered Trust / HUF etc. The tenderer(s) shall enclose the attested copies of the constitution of their concern, and copy of PAN Card along with their tender. Tender Documents in such cases are to be signed by such persons as may be legally competent to sign them on behalf of the firm, company, association, trust or society, as the case may be. (ii)Following documents shall be submitted by the tenderer
(a)Sole Proprietorship Firm: All documents in terms of Para 10 of the Tender Form (Second Sheet) above (As per GCC-2022). (AFFIDAVIT BY SOLE PROPRIETORSHIP FIRM as per Annexure-O-1 in tender document)
(b)HUF: i) A copy of notarized affidavit on Stamp Paper declaring that he who is submitting the tender on behalf of HUF is in the position of 'Karta' of Hindu Undivided Family (HUF) and he has the authority, power and consent given by other members to act on behalf of HUF. (ii) All other documents in terms of Para 10 of the Tender Form (Second Sheet) above.as per GCC-2022.
(c)Partnership Firm: All documents as mentioned in para18 of the Tender Form (Second Sheet) as per GCC-2022.As per GCC- 2022. (Annexure-O-2 of tender booklet.)
d) Joint Venture (JV): All documents as mentioned in para 17 of the Tender Form (Second Sheet).as per GCC-2022.
(e)Company registered under Companies Act2013: (i) The copies of MOA (Memorandum of Association) / AOA (Articles of Association) of the company (ii) A copy of Certificate of Incorporation (iii) A copy of Authorization/Power of Attorney issued by the Company (backed by the resolution of Board of Directors) in favour of the individual to sign the tender on behalf of the company and create liability against the company. (iv) All other documents in terms Para 10 of the Tender Form (Second Sheet) above.(Eligibility Criteria) above as per GCC-2022. (Annexure-O-10 of tender booklet.)
(f)(i) A copy of LLP Agreement (ii) A copy of Certificate of Incorporation (iii) A copy of Power of Attorney/Authorization issued by the LLP in favour of the individual to sign the tender on behalf of the LLP and create liability against the LLP. (iv) An undertaking by all partners of the LLP that they are not blacklisted or debarred by Railways or any other Ministry / Department of the Govt. of India from participation in tenders / contracts as on the date of submission of bids, either in their individual capacity or in any firm/LLP or JV in which they were / are partners/members. Concealment / wrong information in regard to above shall make the contract liable for determination under Clause 62 of the Standard General Conditions of Contract. (v) All other documents in terms of Para 10 of the Tender Form (Second Sheet)..(Eligibility Criteria) above as per GCC2022. (Annexure : O-11 O-12 & O-13 of tender booklet.)
g)Registered Society & Registered Trust: (i) A copy of Certificate of Registration (ii) A copy of Memorandum of Association of Society/Trust Deed (iii) A copy of Power of Attorney in favour of the individual to sign the tender documents and create liability against the Society/Trust. (iv) A copy of Rules & Regulations of the Society (v) All other documents in terms of Para 10 of the Tender Form (Second Sheet) above.
The tenderer whether sole proprietor/ a company or a partnership firm/registered society / registered trust / HUF / LLP etc if they want to act through agent or individual partner(s), should submit along with the tender, a copy of power of attorney duly stamped and authenticated by a Notary Public or by Magistrate in favour of the specific person whether he/they be partner(s) of the firm or any other person, specifically authorizing him/them to sign the tender, submit the tender and further to deal with the Tender/ Contract up to the stage of signing the agreement except in case where such specific person is authorized for above purposes through a provision made in the partnership deed / Memorandum of Understanding / Article of Association /Board resolution, failing which tender shall be summarily rejected.
Please submit your correspondence address, e-mail ID and valid phone number.
Please submit your bank details i.e. Name of the Bank along with Bank Branch Code, Account Number, IFSC Code, and PAN Number.as per annexure -J of tender booklet.
Please furnish list of plant and Machinery available on hand own and proposed to be inducted own and hired to be given separately for the subject work.
Please furnish list of Works on hand indicating Description of Work, Contract Value, Approximate value of balance work yet to be done and Date of award
Please furnish list of personal, organization available on hand and proposed to be engaged for the subject work.
Each page of the tender papers will be treated as signed/accepted by the tenderer(s) or such person(s) on his/their behalf who is/are legally authorized to sign for him/them.
Any DIPP certificate submitted along with the tender document for, exemption of EMD should be valid on the date of opening of the tender, else the tender offer will be summarily rejected.
Please enter the percentage of local content in the material being offered. Please enter 0 for fully imported items, and 100 for fully indigenous items. The definition and calculation of local content shall be in accordance with the Make in India policy as incorporated in the tender conditions.
Declaration form regarding site etc. as per annexure -C of tender booklet.
Declaration regarding constitution of firm as per Annexure-D of tender booklet.
Engineers/Personnel as per annexure -F of tender booklet.
Performa of Completion Certificate as per annexure -L of tender booklet.
The tenderers may also upload the following documents along with his/their tender: The tenderer may upload statement, which shall contain organizational set up and working systems to be adopted by the successful tenderer s during the operation of the contract. It shall contain the details of man power and machineries in the prescribed format and details of methodology for planning, execution, monitoring and completion of the project. The methodology so adopted shall suit to the nature of work and shall also comply fully with best practice and current regulations. A comprehensive detailing for each activity like setting-up organization, safety plan, execution plan, quality assurance plan, sequence of work to achieve the mile stones, ensure targeted progress and quality and in turn deployment of resources, risk analysis and its mitigation strategy shall be given communication arrangement within his organization and with the railways for decisions, progress or any other matter connected with this project to ensure full information about the project including progress of work at different time scale shall also be furnished.
List of works completed in the last seven financial years giving description of work, organization for whom executed, approximate value of contract at the time of award, date of award and date of scheduled completion of work. Date of actual start, actual completion and final value of contract should also be given.
Supportive documents/certificates from the organizations with whom they worked/are working as list of works completed and list of works on hand should be enclosed.
List of works on hand indicating description of work, contract value, and approximate value of balance work yet to be done and date of award .annexure -H
Uploading of declaration regarding Employment/Partnership etc. of Retired Railway Employees as per GCC-2022 as per annexure -Q of tender booklet.
Uploading of Tender Forms shall embody the contents of the contract documents either directly or by reference and shall be as per specimen form, Annexure-I. e-Tender Forms shall be issued free of cost to all tenderers.
A copy of certificate stating that they are not liable to be disqualified and all their statements/documents submitted along with bid are true and factual. Standard format of the certificate to be submitted by the bidder is enclosed as Annexure-V. In addition to Annexure-V, in case of other than Company/Proprietary firm. Annexure-V(A) shall also be submitted by the each member of a partnership firm/Joint Venture (JV)/ Hindu Undivided Family (HUF)/ Limited Liability Partnership (LLP) etc. as the case may be.Non submission of a copy of certificate by the bidder shall result in summarily rejection of his/their bid. It shall be mandatorily incumbent upon the tenderer to identify, state and submit the supporting documents duly self attested/digitally signed by which they/he are/is qualifying the Qualifying Criteria mentioned in the Tender Document. (As per Railway board letter no.2022/CE-l/CT/GCC- 2022/Policy dt. 13.12.2022)
EI alteration & other S&T work in connection with provision of loop lines on Guna line at Sithauli-A Cabin Station in Jhansi Division.
JHS-N-GSU-12-26
JHS-N-GSU-12-26
Open
Works - General
12 Months
Jhansi, Uttar Pradesh
₹0
₹5.2 L
14 Jul 2026
22 Jun 2026
30 Jun 2026
294 items across 2 schedules
| # | Description | Unit | Qty | Rate | Amount |
|---|---|---|---|---|---|
| — | — | — | 1,87,47,066.8 | ||
| — | 10.00 | — | — | ||
| Multi section Digital Axle Counter (MSDAC) supply, design, installation, testing and commissioning of multi section digital axle counter (MSDAC) complete system as per RDSO Specification INo.RDSO/SPN/176/2013 version 3 with Latest amendments or latest. Suitable for commissioning of yard/Auto Section / dual detection (DCTC/AFTC with MSDAC) . MSDAC should have facility to reset track sections. Design of axle counter circuit indoor installation testing and commissioning of multi section digital axle counter (per unit), supply of essential 10% spares covering all types of cards, 'wheel sensors for MSDAC . Supply of Diagnostic system for Remote diagnostics Tool set for wheel sensor mounting and maintenance of MSDAC consisting of torque wrench, ratchet, testing plate , measuring tape , screw driver, gloves and multimeter fluke 115 (1 Nos. per 14 DP). " "NOTE-1 : 1. If any housing is required to keep outdoor equipment, it has to be supplied with the equipment with no extra cost. 2. Maintenance free earthing (supply and installation) for track device/mushroom housing etc to be done by the contractor if required by system design. No extra cost/ payment will be made by this Railway: 3. Automatic resetting facilities through hardware /software for auto resetting to be |provided by contractor by his own materials for this no extra cost /payment will be made by Railways. 4. MSDAC system networking to be done with central control room. Required hardware PC/ network equipment to be provided by the contractor, no extra cost/payment will be made for this by Railway. E1 Channel/media will be provided by Railway for this purpose from nearest Railway station. 5. All other Hardware like TPR, Extra card to make dual DP, Modem, ethernet switches etc if required for commissioning and final track section pick up will be supplied by contractor, no extra payment will be made by this Railway. 6 Separate evaluator for UP and Down line to be provided at Station/RH as decided by Railway site engineer. For the communication between evaluator to evaluator (RH to Station) Quad/ OFC Link (dark fiber) will be provided by Railway. Any other Networking equipment if required will be supplied by contractor at no extra cost. 7. Manual resetting through reset box at station to be provided as per requirement." The DP configuration/track section may vary as per site , therefore material to be supplied as per instruction of engineer incharge. The material to be supplied as per Annexure-X attached. (Inspection Agency by RDSO). | — | — | — | 31,75,666.2 | |
| — | 14.00 | — | — | ||
| Supply of Q-Series Track Relay (QTA2 Type), AC immunized, 9 Ohms, 2F/1B along with plug board (base plate), connectors, retaining clips etc and conforming to BRS: 939A & 966(Appendix F2) or latest and RDSO Specn.No. IRS : S -34 ,S - 23 , S - 60 or latest, as applicable.The interlocking code for this unit shall be "FGHKX".(Inspection Agency by RDSO). | — | — | — | 53,245.5 | |
| — | 20.00 | — | — | ||
| Supply of Q-Series LED ECR (Universal Type i.e.QECX-61), 4F/4B complete with plug board(base plate), connectors, retaining clips etc. and conforming to BRS: 941A STS / E / RELAYS / AC LIT LED SIGNAL / 09 - 2002, Amdt.-1 or latest and RDSO Spec.No.IRS: S - 34, S- 23 or latest, as applicable. The interlocking code for this unit shall be ""ABDHK"".(Inspection Agency by RDSO). | — | — | — | 1,38,347.6 | |
| — | 10.00 | — | — | ||
| Supply of Q-Series Neutral Line Relay(QSPA1 Type), AC immunised, 24V DC,8F/4B along with plug board (base plate), connectors, retaining clips etc and conforming to BRS-933A and RDSO Specn.No.IRS:S-34 , S-23, S-60 or latest, as applicable. Th e interlocking code for this unit shall be "ABDEJ" (Inspection Agency by RDSO). | — | — | — | 60,564 | |
| — | 20.00 | — | — | ||
| Supply of Q-Series Line Relay (QNA1 Type), AC immunized, 8F/8B, 24 V DC along with plug board (base plate), connectors, retaining clips etc. and conforming to BRS- 93 1A and RDSO Specn . No . IRS : S - 34 , S -23 , S - 60 or latest, as applicable. The interlocking code for this unit shall be ABDGH".(Inspection Agency by RDSO). | — | — | — | 88,784.8 | |
| — | 10.00 | — | — | ||
| Supply of Q-Series Neutral Line Relay, Non-AC immunised, (QN1 Type), 8F/8B, 24V DC complete with plug board(base plate), connectors and retaining clips etc and conforming to BRS- 930 and RDSO Specn.No.IRS:S-34 ,S-23, S-60 or latest, as applicable. The interlocking code for this unit shall be "ABCDF".(Inspection Agency by RDSO). | — | — | — | 36,394.1 | |
| — | 10.00 | — | — | ||
| Supply of Contactor Unit (QBCA1 Type), 24 V DC, 2HF/4B complete with plug board(base plate), connectors, retaining clips etc and conforming to BRS- 943 and RDSO Specn.No.IRS:S-34 , S-23 , S-60 or latest, as applicable. The interlocking code for this unit shall be "BCEJK". (Inspection Agency by RDSO). | — | — | — | 53,601.4 | |
| — | 5.00 | — | — | ||
| Supply of Q-Series Twin Neutral Line Relay(QNN1 Type), 4F/4B, 24V DC complete with plug board(base plate), connectors and retaining clips etc and conforming to BRS-960 and RDSO Specn.No.IRS:S-34 & S-23 or latest, as applicable. Th e inter locking code for this unit shall be "ACEHJ" (Inspection Agency by RDSO). | — | — | — | 28,323.75 | |
| — | 5.00 | — | — | ||
| Supply of Q-Series Twin Neutral Line Relay(QNNA1 Type), AC immunised, 4F/4B, 24V DC complete with plug board(base plate), connectors and retaining clips etc and conforming to BRS- 960 and RDSO Specn.No.IRS:S-34 , S-23, S-60 or latest, as applicable. The interlocking code for this unit shall be "ACDHJ". (Inspection Agency by RDSO). | — | — | — | 27,912.35 | |
| — | 10.00 | — | — | ||
| Supply of Q-Series Magnetically Latched Neutral Line Relay (QL1 Type), 11F/4B,24V DC complete with plug board(base plate), connectors and retaining clips and con forming to BRS- 935A and RDSO Specn.No.IRS:S-34 , S-23 or latest, as applicable. The interlocking code for this unit shall be "ABDEG (Inspection Agency by RDSO). | — | — | — | 53,172.2 | |
| — | 2.00 | — | — | ||
| Supply of DC neutral line relay QNA1K, AC immunised, DC neutral line 24V, 6F/6B con tacts, complete with plug board, retaining clip and connectors. Conforming to BRS:931A & RDSO letter No. STS/E/Relays/UEA/PI dated 30.05.97 Annexure II and IRS:S34, IRS:S23 , IRS:S-60 or latest, as applicable. The interlocking code for this unit shall be "CDEKY" (Inspection Agency by RDSO). | — | — | — | 8,913.6 | |
| — | 3.00 | — | — | ||
| Supply of Key Lock Checking Relay (KLCR) working on 24V DC, AC Immu nized, metal to metal, with diff erent ward combinations and contact confi gura tion 4F/4B with 2 extra ward plates, RDSO spec No. RDSO/SPN/219/2016 Ver 1.0 with Amendment-1 or latest. (Inspection Agency By consignee) | — | — | — | 24,069.54 | |
| — | 1.00 | — | — | ||
| Supply and installation of prewired KLCR Box, wooden crank handle lock inside box, with 8 way terminal strips, LEDs of approved type, for fi xing of EKT on wooden board inside box form installating KLCRs/EKTs up to 06 No., including supply of all material like board, handle, hinges, glass sheet etc. (Inspection Agency by consignee) | — | — | — | 13,359.12 | |
| — | 2.00 | — | — | ||
| Supply of Fail Safe Electronic Flasher device, 24V DC or 60 V DC, as per RDSO spec. No. RDSO/SPN/173/2002, Amdt.2 or latest. (Inspection Agency by RDSO). | — | — | — | 22,509.54 | |
| — | 1.00 | — | — | ||
| Supply, wiring, installation and commissioning of Earth Leakage Detector (ELD) having 6 digit counter, 12 Channel bus bar, voltage of 110V/60V/ 24V/12V in AC/DC measurement as per RDSO Spec.No. RDSO/SPN/256/ 2002 or latest. This includes supply of fuse terminal strip for incoming power supply wires. In stallation to be done on 19 inch sub rack along with insulation resistance meter, remote indication and buzzer in ASM room. (Inspection Agency by RDSO). | — | — | — | 1,91,255.56 | |
| — | 4.00 | — | — | ||
| Supply of DC-DC converter 24-32 V, 5 Amp compatible with existing IPS system. Inspection: RDSO Inspection Charges: Borne by railways. (Inspection Agency by RDSO). | — | — | — | 1,01,747.4 | |
| — | 4.00 | — | — | ||
| Supply of DC-DC converter 24- 32 V, 10 Amp compatible with existing IPS system. Inspection: RDSO Inspection Charges: Borne by railways. (Inspection Agency by RDSO). | — | — | — | 1,09,298.16 | |
| — | 3.00 | — | — | ||
| Supply of Relay Racks and Wiring accessories. (Inspection Agency by RDSO). | — | — | — | 24,20,781.66 | |
| — | 11.00 | — | — | ||
| Supply of DC-DC Converters for EI (MEdha Make). (Inspection Agency by RDSO). | — | — | — | 2,23,245 | |
| — | 64.00 | — | — | ||
| Supply of Fuse auto changeover system for Railway Signaling System as per RDSO/SPN/209/2012 Rev.2 or latest for Relay room fuses up to 10 Ampere ca pacity for 12V/24V/60V/110V DC and 110V AC systems. Th e units shall be mounted on DIN rail in adequate size enclosure as per instructions of Railway site engineer. Two No. of NO+NC contacts shall be provided for remote moni toring. Th e changeover time shall be less than 1 msec. Th e audio visual alarm for main and standby fuses shall be provided. One set means set of each fuse. (Inspection Agency by RDSO) | — | — | — | 1,43,980.16 | |
| — | 1.00 | — | — | ||
| Supply and installation of Cable Termination(CT) rack as per drawing of NC Railway, complete along with fitting arrangements, wall supports, scaffolding and suitable grouting arrangements and also with Arrangement for fixing four 8-way terminal strips/ Screw less terminals/ ARA terminals. The CT rack shall be covered with hylum sheet of minimum 10 mm thickness for fixing of 8-way terminal strips/ Screw less terminals/ ARA terminals. Supply of 8 way terminal strips/ Screw less terminals / ARA terminals not covered under this item. Cable termination rack shall be corrosive resistant and powder coated.(Inspection Agency by consignee) | — | — | — | 47,146.84 | |
| — | 2.00 | — | — | ||
| Supply of Relay Rack Assembly with scaffolding,fixtures and accessories including MS Bars for fixing of relay,plug board,string rods,fuse strips with bracket,11 Way Bus Bars with cover and mounting brackets,runway for cable/wires,frame,base,assembly etc. as per extant practice on the division. (Inspection Agency by consignee) | — | — | — | 52,498.84 | |
| — | 80.00 | — | — | ||
| Supply of Phoenix Contact Fuse Terminal ST 4 HESILED 24(5X20), Make: Phoenix or similar including fuse link.(Inspection Agency by consignee) | — | — | — | 10,071.2 | |
| — | 25.00 | — | — | ||
| Supply of non deteriorating type, Round head type, low voltage cartridge fuse as per Spec No. IRS: S -78/92 with latest amendments, 2A/4A/6A/8A/10A rating capacity. (Inspection Agency by RDSO) | — | — | — | 3,078.5 | |
| — | 25.00 | — | — | ||
| Supply of Cartridge Fuse block, made of PBT, as per RDSO spec. No. IRS: S-75/2006 (Rev.2) or latest and as per Drawing. No. SA- 23748 (Alt.-4) or latest. (Inspection Agency by RDSO) | — | — | — | 6,088.75 | |
| — | 3000.00 | — | — | ||
| Supply of Disconnect Terminal block for four conductors with screwing cage/clamp type, sliding switch disconnect, as per RDSO spec. RDSO/SPN/189/2004 Ver. 3.0 or latest, for each conductor size up to 2.5 sq. mm, equivalent of M6 terminals. Each terminal block equipped with two markers, on top and bottom, an end plate, two end clamps and adequate lenght of rails for fitting terminal blocks. (Inspection Agency by RDSO) | — | — | — | 5,78,160 | |
| — | 600.00 | — | — | ||
| Supply of 16/0.2 mm (0.5 sq mm) PVC insulated multi strand, single core, tinned copper conductor, as per RDSO Specn.No.IRS:S-76/89 (Amnd-3) or latest. Each coil should be of 100/200/500 Meters length. Colour of the wire will be specified by the Engineer incharge. (Inspection Agency by consignee) | — | — | — | 6,450 | |
| — | 150.00 | — | — | ||
| Supply of 1 x 6 Sq mm (Red/Black/Green) multi strand copper power wire , 85 conductor each dia 0.30 +/- 0.01 with insulation thickness of 0.8 mm and nominal conductor resistance of 3.3 ohms/km and test paraMtr.s as per RDSO Specn. No.IRS:S-76/89 (Amnd.3) or latest. Colour of the wire will be specified by the Engineer incharge. (Inspection Agency by consignee) | — | — | — | 7,200 | |
| — | 100.00 | — | — | ||
| Supply of 1 x 10 Sqmm (Red/Black/Green) multi strand copper power wire, 101 conductor each dia 0.45 +/- 0.01 with insulation thickness of 1.2 mm and nominal conductor resistance of 1.127 ohms/km and test parameters as per RDSO Specn. No.IRS:S-76/89(Amnd.3) or latest. Colour of the wire which is required will be specified by the Engineer incharge. (Inspection Agency by consignee) | — | — | — | 13,246 | |
| — | 100.00 | — | — | ||
| Supply of 1 x 16 Sqmm (Red/Black/Green) multi strand copper power wire as per IS: 2465/1984 and IS:694:2010 or latest, 101 conductor each dia 0.45 +/- 0.01 with insulation thickness of 1.2 mm and nominal conductor resistance of 1.127 ohms/km and test parameters as per RDSO Specn. No.IRS:S-76/89(Amnd.3) or latest. Colour of the wire which is required will be specified by the Engineer incharge. (Inspection Agency by consignee) | — | — | — | 14,787 | |
| — | 100.00 | — | — | ||
| Supply of 1 x 25 Sqmm (Red/Black/Green) multi strand copper power wire, Colour of the wire which is required will be specified by the Engineer incharge.(Inspection Agency by consignee) | — | — | — | 40,875 | |
| — | 5.00 | — | — | ||
| Supply of Electric Point Machine 143 mm stroke, AC Immunity 160V AC, complete with lock detector and slides for lock detector, non-trailable, to operate on 110V DC, rotary locking with crank handle universal type as per RDSO Spec. No. IRS:S- 24/2002 (Amnd. 1) or latest, RDSO DRG. NO S-10800 (ALT.5) WITH JUNCTION BOX TELESCOPIC. THE MOTOR WILL BE AS PER RDSO SPECN. NO. IRS: S-37/82 (AMND. 3) WITH RDSO DRG. NO. S-10910. This includes supply of Set of tools as per para 20.1 & 20.2 of RDSO SPECN. NO. IRS:S- 24/2002 (AMND 1) The following set of tools in a suitable toolbox shall be supplied along with every set of eight point machines or less. i). Hand operated square drive socket wrenches of 12.5 mm driving square (short type) as per IS: 7381 for M8, M10, M12 & M18 threads. (One 250 mm long 12.5 mm square extension bar as per IS: 7991 along with compatible Tee handle square drive as per IS: 7975 suitable for above socket wrenches shall also be provided.) ii). Open jaw wrenches (spanners) for M10, M12, M20, M24 & M33 threads as per IS: 2028. iii). Adjustable wrench. iv). Screwdriver 300 mm long. 20.2 Junction box and two numbers of telescopic pipes of approved type shall be supplied. as an integral part of the point machine. (Inspection Agency By RDSO) | — | — | — | 5,02,012.5 | |
| — | 5.00 | — | — | ||
| Supply and fixing of GI bend pipe 50 mm dia.,'B'class, for cable entry into Point machine with all accessories. Note: Th is item to be operated independently for those points where Point machines are functional but GI bend pipe is not pro vided. For all other new installation of Point machines, item 06002 of the SOR includes the provision of GI bend pipe. (Inspection Agency by consignee) | — | — | — | 15,943.75 | |
| — | 20.00 | — | — | ||
| Supply of gauge tie plate insulation complete set each set consisting plate T-10372 = 1No., Bush T-10368=3 Nos. and washer - T-10371 = 6 Nos.(Inspection Agency by consignee) | — | — | — | 7,638.8 | |
| — | 20.00 | — | — | ||
| Supply of IRS Type point machine 'D'/'P' bracket insulation complete set con sifting of the following:- Plate LH - S-3266-1 No., RH - S-3265-1 No., Plate S-8804- 1 No., Bush - S- 3199 - 4 Nos, Bush S-8813- 2 Nos.(Inspection Agency by consignee) | — | — | — | 9,600.2 | |
| — | 20.00 | — | — | ||
| Supply of stretcher bar insulation complete set consisting of the following:- Plate-T- 10367-1 No., Bush T- 10368- 3 Nos. and washer-T- 10371 -6 Nos.(Inspection Agency by consignee) | — | — | — | 7,629.8 | |
| — | 5.00 | — | — | ||
| Fabrication and supply of point rodding (Ground Connection ) set for electric point machine (RDSO Type) as per RDSO Org. No.SA- 8800-01, 20-21, 915 1-52,9000-01,03-04,9065- 66,9101, as applicable." (Inspection Agency by consignee) | — | — | — | 73,646.35 | |
| — | 20.00 | — | — | ||
| Supply of uncharged Low Maintenance Lead Acid (LMLA) secondary cell, 2V, 80 AH, in dry condition, shelf mounting type, conforming to RDSO Specn.No.IRS:S-88/2004 or latest, with inter cell connectors, nuts and bolts, washers, micro porous vent plug, float etc. (Inspection Agency by consignee) | — | — | — | 63,909.2 | |
| — | 10.00 | — | — | ||
| Supply of Track feed Battery Charger as per RDSO Specn. No.IRS: S-89/2013 Ver. 1.0 or latest. Charging capacity rating should be suitable for charging 80 AH Battery. (Inspection Agency by RDSO). | — | — | — | 59,005.6 | |
| — | 20.00 | — | — | ||
| Supply of B Type Choke as per RDSO Specn.No.IRS:S-65/83 (Amnd. 3) or latest. The materials to be procured from RDSO approved firm. (Inspection Agency by RDSO). | — | — | — | 1,18,182.6 | |
| — | 10.00 | — | — | ||
| Supply of Adjustable Track Feed Resistance 30 Ohms (Disc Type), Phenolic moulded base, as per RDSO Drg . No. SA-20161-66/M or latest.(Inspection Agency by RDSO). | — | — | — | 22,797.8 | |
| — | 400.00 | — | — | ||
| Supply of 8 SWG GI wire (4 mm dia) suitable for Track circuit rail bonding as per RDSO spec.No. IRS: S 13@45>46@ (Inspection Agency by consignee) | — | — | — | 36,016 | |
| — | 2000.00 | — | — | ||
| Supply of PVC insulated, jacketed wire rope for Track lead connections. Th e wire rope should be of galvanised steel, 6 mm dia, (6x19 stranded wire with steel core of 6 mm) sheathed with PVC.(Inspection Agency by consignee) | — | — | — | 87,060 | |
| — | 2500.00 | — | — | ||
| Supply of Channel pins, single groove, 7 mm, galvanised, suitable for 4 mm dia bonding wire for Track Circuit rail bonding, as per RDSO spec. IRS: S 17-75. (Inspection Agency by consignee) | — | — | — | 11,375 | |
| — | 50.00 | — | — | ||
| Supply of Track Lead Junction Box (TLJB), 4 way, 250 mm x 255 mm x120 mm made from FRP, as per Drg.No. 20101/M(IRS) or latest, including brass bolts and hylam board sheet with terminals etc. Th e FRP material shall be as per RDSO spec.No. RDSO/SPN/151/1997 or latest. Th e technical specifications are as follows: (a) TLJB complete with cover to be in black/red/grey with all the holes required for mounting on FRP stump (vertical two for each FRP angle) HDPE pipe, cable etc. (b) Each TLJB shall have two bakellite terminal block fitted horizontally, each bakellite terminal block shall have two nickel chrome plate with brass terminal. Along with each TLJB, nickel chrome plated brass links(two nos. of adequate strength for vertical linking of the terminals to be supplied. (c) HDPE pipe along with two nuts for fixing on the TLJB hole. (d) The FRP stump for mounting the TLJB. (Inspection Agency by consignee) | — | — | — | 2,72,802 | |
| — | 10.00 | — | — | ||
| Supply, fabrication and fixing of Retro-refl ective Signal number plates as per NCR latest practice, on signal post with contractor's own materi al like clamp, U bolts, nuts etc. (Inspection Agency by consignee) | — | — | — | 7,445 | |
| — | 6.00 | — | — | ||
| Supply of Colour Light Signal Post, Tubular Mild steel, 4.5 meter length, 140 mm Dia, as per RDSO spec. No. IRS: S-6/81 or latest and Supply of cast iron Main signal surface base (As per NCR latest practice), with CLS ladder assembly suitable for colour light signal 4.5 meter long, as per RDSO drg. No. SA 23153 and signal front staging complete assembly and complete signal back staging for CLS unit.(Inspection Agency by consignee) | — | — | — | 1,51,642.08 | |
| — | 2.00 | — | — | ||
| Supply of Junction route indicator unit 2 way/3 way, made of FRP, (Without Lenses & Holder) as per Drg. No. SA 23401-06 (Adv.) (as applicable) suitable for LED Signal Lighting Unit and as per RDSO spec.No. IRS: S-66/84 Amd.-1 or latest and RDSO/SPN/194/2006 Rev.2 or latest. (Inspection Agency by consignee) | — | — | — | 90,917.22 | |
| — | 3.00 | — | — | ||
| Supply of Offset brackets for Main Signal, made of Mild Steel, outer diameter 140 mm (5.5 inch), thickness of pipe 4.5 mm with fixing arrangement on Main Signal post as per Drawing No. SA-23080/Adv. along with fixing U bolts, nut and clamps." (Inspection Agency by consignee) | — | — | — | 3,619.77 | |
| — | 3.00 | — | — | ||
| Supply of Position Light Shunt Signal Unit Complete, Non-Metallic, made of FRP as per Drg. No. SA-23840 (Adv.) suitable for LED Signal Lighting Unit. (Supply of LED Unit is not covered in this item). (Inspection Agency by consignee) | — | — | — | 44,687.37 | |
| — | 2.00 | — | — | ||
| Supply of Calling ON Signal Unit, Non metallic, with Brackets, clamps and fixing accessories, suitable to LED signal lighting unit and as per RDSO spec. No. RDSO/SPN/194/2006 (Rev. 2.0) or latest. Th e FRP material shall conform to RDSO/SPN/151/1997 or latest. Calling On Signal Unit shall conform to RDSO Drg No. SA-24351(Adv) Alt1 or latest without lamp, lamp-holder and lens.(Inspection Agency by consignee) | — | — | — | 23,324.12 | |
| — | 2.00 | — | — | ||
| Supply, fabrication and fixing of the Calling On board/BSLB board as per /Stop/Warning board as per NCR latest practice, or as applicable, on concrete foundation and painting with Retro reflective paint. All work to be carried out as per Railway site engineer instructions.(Inspection Agency by consignee) | — | — | — | 16,217.56 | |
| — | 15.00 | — | — | ||
| Supply of hand cuff lock of Godrej/Navtal or reputed make with key and as approved by site engineer.(Inspection Agency by consignee) | — | — | — | 6,806.4 | |
| — | 10.00 | — | — | ||
| Supply of Non Metallic (FRP) colour light signal housing multi unit type for railway signaling suitable for RE area TWO Aspects, complete without lenses, lamps and signal transformer as per RDSO Drg. No. SA 23003A/M (Adv.) and as per RDSO spec. No. RDSO/SPN/194/2006 (Rev 2.0) or latest and FRP material as per RDSO SPEC. No. RDSO/SPN/151/1997 or latest. (Inspection Agency by consignee) | — | — | — | 3,13,080.8 | |
| — | 3.00 | — | — | ||
| Supply of Non Metallic (FRP) colour light signal housing multi unit type for railway signaling suitable for RE area THREE Aspects, complete without lenses, lamps and signal transformer as per RDSO DRG. No. SA 23002 A/M (Adv.) and as per RDSO spec. No. RDSO/SPN/194/2006 (Rev 2.0) or latest and FRP mate rial as per RDSO SPEC. No. RDSO/SPN/151/1997 or latest. (Inspection Agency by consignee) | — | — | — | 1,07,212.11 | |
| — | 4.00 | — | — | ||
| Supply of Apparatus Case/Location Box Full as per RDSO drg. no. RDSO/S-11500 or latest, with 'E' type lock and key ward no. 42, . The key and handle should be supplied at the rate of one no. per four Apparatus cases. The 'E' type key lock is as per RDSO Spec. IRS;S-30/64 or latest, RDSO drg. no.SA 3376/M or latest and Key is as per Drg. No. 3377/M or latest. Note: This item includes the supply of 2 Nos E Type Lock fitted on both doors, along with two Keys.(Inspection Agency by consignee) | — | — | — | 1,09,999.24 | |
| — | 2.00 | — | — | ||
| Supply of Apparatus Case/Location Box Half as per RDSO drg. No. RDSO/S-11507 or latest, with 'E' type lock and key ward No. 42,. T h e key and handle should be supplied at the rate of one no. per four Apparatus cases. Th e 'E' type key lock is as per RDSO drg. No. SA3376/M or latest and Key is as per Drg. No. 3377/M or latest. Note: Th is item includes the supply of 2 Nos E Type Lock fitted on both doors, along with two Keys. (Inspection Agency by consignee) | — | — | — | 39,809.38 | |
| — | 15.00 | — | — | ||
| Supply of Phenolic laminated Sheet, resin bonded, grade P3 in standard size of 1220 X 1220 x 10 mm as per spec. No IS 2036 of 1995 or latest. Test report of manufacture to be supplied.(Inspection Agency by consignee) | — | — | — | 87,406.95 | |
| — | 10.00 | — | — | ||
| Supply of thermo shrink jointing kit as per RDSO Specn.No. IRS: TC 77-2012 (Rev.3.0) with (Amdt.-1 to 3) or latest, suitable for 6 Quad/jelly filled cables for straight through/derivation joints. It includes supply of all the accessories, with out transformer.(Inspection Agency by consignee) | — | — | — | 33,611.5 | |
| — | 2.00 | — | — | ||
| Supply, Installation and commissioning of central gateway. Note: Single centre gateway shall cater maximum up to 32 data transmitter node (Modbus).(As per Annexure A). (Inspection Agency by consignee) | — | — | — | 4,23,171 | |
| — | 38.00 | — | — | ||
| Supply, Installation ,testing and commissioning of data transmitter Node in location box. Modbus Type Note: Maximum range 400 meter.(As per Annexure B). (Inspection Agency by RDSO) | — | — | — | 6,78,954.36 | |
| — | 4.00 | — | — | ||
| Supply, Installation , testing and commissioning of data transmitter Modbus cum repeater for augmenting range of our door data transmitter node (Modbus), where distance of location box is more than 400 meter with respect to central gateway.(As per Annexure C). (Inspection Agency by RITES/RDSO) | — | — | — | 71,468.88 | |
| — | 2.00 | — | — | ||
| Apparatus case Led indication status display unit cum allarm system for yard. Single Display system shall cater to maximum 45 no of location boxes.(As per Annexure D) (Inspection Agency by consignee) | — | — | — | 42,317.1 | |
| — | 10.00 | — | — | ||
| Supply of basic material to construct unit maintenance free earth as per RDSO Specs. No. RDSO/SPN/197 Ver. 1.0 or latest to achieve a resistance less than 1 ohm. It consist of following: (a) Copper bonded steel electrode of minimum 3.0 meter long, minimum 17.0 mm dia with copper bonding thickness of minimum 250 microns and UL listed and marked = 1 No. (b) Earth enhancement material supplied in sealed bags of minimum 10 kg = 3 Nos. (c) Copper strip of 150x25x6 mm, to terminate earth rod = 1 No.(d) Copper strip of 300x25x6 mm (MEEB) = 1 No. (e) Copper strip of 150x25x6mm (SEEB) = 1 No. |Gi) Supply of 35 sq. mm multi strand single core PVC insulated copper cable as per IS: 694 for connecting main earth electrode to MEEB in the equipment room in duplicate. (minimum 10 meter.) (iii) Supply of 16 sq. mm multi strand single core PVC insulated copper cable as per IS: 694 for connecting MEEB to SEEB and SPD to MEEB (minimum 10 meter. ) (iv) Supply of 10 sq. mm multi strand single core PVC insulated copper cable as per IS: 694 for connecting various equipment's to SEEB (v) Supply of copper lug sleeve for 3/16 cable. (Inspection Agency by consignee) | — | — | — | 1,80,425.2 | |
| — | 30.00 | — | — | ||
| Supply and installation of earth electrode as per standard practice and as per NCR latest practice. It includes supply of GI pipe of 3m length. It includes connecting the earth electrode to the equipments which are required to be earthed including digging of earth pit 3 mtr deep and fixing earth electrode pipe, casting of cement concrete enclosure with cover (cover as per NCR latest practice). It includes installation of 7 strand GI wires as earth lead wires, supported on MS flat size 5mm x 40 mm, soldering and nut bolt both, one end of both earth lead wire and MS flat to earth electrode and other end to Location boxes, block equipment's, power equipment's, cable sheath, signals etc. as per site requirement and as per instructions given by engineer incharge.(Inspection Agency by consignee) | — | — | — | 1,00,606.2 | |
| — | 1000.00 | — | — | ||
| Supply of Double Walled Corrugated (DWC) Pipe/duct with associated collars etc. as per RDSO Specification No. RDSO/SPN/204/2011 or latest anti-rodent & anti-oxidant and Non flame propagating type in 6 meter straight length and of size 120 mm outer dia, & 103.5 mm inner dia. (Th e manufacturers, suppliers must produce valid IS license and should be certified under ISO 9000 and shall submit copy of certificate). One coupler with suitable rubber O-ring should be supplied with every 6m of pipe length. DWC pipe shall be marked at every 1 mtr length in such a way that manufacturer's name, vendor name and year of manufacture can be easily identified. (Inspection Agency by RITES) | — | — | — | 6,06,870 | |
| — | 20.00 | — | — | ||
| Supply of LPS 3.00 mm thick Rolled Copper Strip. (Inspection Agency by consignee) | — | — | — | 22,500 | |
| — | 2.00 | — | — | ||
| Supply and testing of cable route tracer and marker locator of make 3M model- 2273MID/ECU 12W-RT or similar, meet to tech GR TIE-01/02.OCT'99& TEC/GR/TX/TIE-007/02.MAR-14 or latest. Consignee shall approve the supply only after successful demonstration at site. (Inspection Agency by RITES). | — | — | — | 9,68,146.46 | |
| — | 1.00 | — | — | ||
| Supply of portable maintenance Service Terminal for installation, testing and maintenance of all networking parameters, as per Technical Specification. Make:- HP/Dell or superior. (Inspection Agency by consignee) | — | — | — | 70,765.72 | |
| — | 2.00 | — | — | ||
| Supply of Digital Clamp Earth tester/meter, with memory storage facility, make Motwane/Meco/Fluke/Stanley or better.( Model no. MECO 4680 or similar or latested ) Make and model should be approved by railway representative before supply. (Inspection Agency by consignee) | — | — | — | 2,31,687.12 | |
| — | 11.00 | — | — | ||
| Supply of Metravi 4673 mini digital clamp meter features high reliability, safety, precision and compact design. Its resolution ratio is 1mA. AC/DC Current has maximum range of 100A AC/DC; particular VFC start mode. Entering this mode can accurately measure voltage and current which has VFC frequency conversion. Voltage or current response display is T-RMS. Whole range overload protection, reliable measurement accuracy and unique design makes it an outstanding new generation electrician/electric power measurement instrument. (Inspection Agency by consignee) | — | — | — | 67,129.04 | |
| — | 6.00 | — | — | ||
| Supply of Insulation resistance tester. Make Fluke 1507 or similar or latest version. (Inspection Agency by consignee) | — | — | — | 2,95,882.2 | |
| — | 2.00 | — | — | ||
| Supply, Installation, Testing & Commissioning of Microprocessor based Networkable analog addressable and modular type of fire Alarm Control panel with display with 2 loop expandable up to four loop, power supply and battery back up as per RDSO specification no. RDSO/SPN/217/2021 ver 3.0 or latest, including GSM module-01 No. for sending SMS to configured mobile number and relay module-02 Nos. for connecting to data logger for remote monitoring. The panel should support sufficient devices of both detectors and modules in a single line circuit. (Inspection Agency by consignee) | — | — | — | 1,95,452.16 | |
| — | 30.00 | — | — | ||
| Supply, Installation, Testing and Commissioning of Addressable heat & smoke Multi sensor. As per RDSO Specification No. RDSO/SPN/217/2021ver 3.0 or Latest). (Inspection Agency by RDSO) | — | — | — | 91,605.3 | |
| — | 4.00 | — | — | ||
| Supply, Installation, Testing & Commissioning of Hooter cum Strobe including its control module.(as per RDSO Specification No. RDSO/SPN/217/2021 ver 3.0 or latest.(Inspection Agency by RDSO). | — | — | — | 9,660.32 | |
| — | 60.00 | — | — | ||
| CPVC PIPE and all other associated fittings. As per RDSO Specification No. RDSO/SPN/217/2021 ver 3.0 or Latest) (Inspection Agency by RDSO). | — | — | — | 70,146 | |
| — | 3.00 | — | — | ||
| Supply, Installation, Testing & Commissioning of Analogue Addressable & reset table Manual Call Point with inbuilt short circuit fault isolator (as per RDSO Specification No. RDSO/SPN/217/2021 ver 3.0 or latest.). (Inspection Agency by RDSO) | — | — | — | 12,581.61 | |
| — | 2.00 | — | — | ||
| Supply, Installation, Testing & Commissioning of Aspiration Systems with single pipe slot along with required module and power supply, interfacing module etc.(as per RDSO Specification No. RDSO/SPN/217/2021 ver 3.0 or latest). (Inspection Agency by RDSO). | — | — | — | 5,76,323.72 | |
| — | 484.00 | — | — | ||
| Supply, Installation, Testing & Commissioning of Fire survival cable 2C X 1.5 Sqmm(unarmored), (as per RDSO Specification No. RDSO/SPN/217/2021 ver 3.0 or latest.). (Inspection Agency by RDSO) | — | — | — | 50,708.68 | |
| — | 210.00 | — | — | ||
| Supply, installation, testing and commissioning analog LHS cable.(as per RDSO Specification No. RDSO/SPN/217/2021 ver 3.0 or latest.). (Inspection Agency by RDSO). | — | — | — | 2,46,569.4 | |
| — | 2.00 | — | — | ||
| Supply, installation, testing and commissioning of LHS interface module for LHS connectivity to control panel. (as per RDSO Specification No. RDSO/SPN/217/2021 ver 3.0 or latest.). (Inspection Agency by RDSO). | — | — | — | 1,53,293.46 | |
| — | 4.00 | — | — | ||
| Supply of operator VDU of size 55 inch, 4K, HDMI/DVI connectivity, inbuilt speaker etc.(Make: Samsung/Sony/LG or similar make) (Inspection Agency by consignee). | — | — | — | 2,25,280 | |
| — | 3.00 | — | — | ||
| Supply ,installation ,testing and commissioning of Automatic change over device for DAC / UFSBI V.21 / V.23 to Optical fibre , STM(E1) , standard 19"" rack mountable device consisting of two E1 port supporting 120 Ohms interface; dual optical ports with (1+1) hot stand by (dual core path and single core path) 20 Kms driving distance and four V.21 /V.23 (E&M) 2W/4W interfaces with auto change over mechanism to Quad ports 2W/4W ; each port configurable as 2W or 4W no restriction in configuration ; unit to support Potential free contacts four numbers can be linked with data logger / RTU for E1 Status , Quad Status & Power Supply status ; Unit support front panel ressetable audio able buzzer in case of main link fails (optical or E1) ; Unit to support power OFF fail safe mechanism when the unit is switched OFF the inputs is bypassed to the Quad cable automatically unit supports ; Unit supports front panel LED indicators for Quad health status ; E1 dual ; Optical dual path ; Dual DC power supply 18VDC to 72 VDC range ; Make : Team link/Team Engg /Cygnus/FABIO1CX - 4P or superior.( Technical Specification as per annexure- A attached). (Inspection Agency:RITES) | — | — | — | 5,42,414.37 | |
| — | 2.00 | — | — | ||
| Supply and installation of Data Concentrator as per technical specifications. (Inspection Agency: RDSO) | — | — | — | 2,89,941.54 | |
| — | 6.00 | — | — | ||
| Supply of IOCOM CPU CARD for spare purpose and for Medha Servo system. (Inspection Agency by RDSO) | — | — | — | 2,58,900.84 | |
| — | 6.00 | — | — | ||
| Supply of IOCOM VOLTAGE AND HEALTH MONITORING CARD for spare purpose and for Medha Servo system.(Inspection Agency by RDSO) | — | — | — | 1,00,807.74 | |
| — | 14.00 | — | — | ||
| Supply of INPUT WFM CPU CARD for spare purpose and for Medha Servo system. (Inspection Agency by RDSO) | — | — | — | 2,91,295.62 | |
| — | 7.00 | — | — | ||
| Supply of OUTPUT WFM CPU CARD for spare purpose and for Medha Servo system. (Inspection Agency by RDSO) | — | — | — | 1,91,039.31 | |
| — | 7.00 | — | — | ||
| Supply of WFM RELAY DRIVER CARD for spare purpose and for Medha Servo system. (Inspection Agency by RDSO) | — | — | — | 1,33,284.69 | |
| — | 3.00 | — | — | ||
| Supply of OCM VITAL CUT-OFF CARD for spare purpose and for Medha Servo system. (Inspection Agency by RDSO) | — | — | — | 93,002.58 | |
| — | 6.00 | — | — | ||
| Supply of POWER SUPPLY CARD TYPE B for spare purpose and for Medha Servo system.(Inspection Agency by RDSO) | — | — | — | 76,388.4 | |
| — | 6.00 | — | — | ||
| Supply of POWER SUPPLY CARD TYPE C for spare purpose and for Medha Servo system.(Inspection Agency by RDSO) | — | — | — | 1,31,048.28 | |
| — | 15.00 | — | — | ||
| — | — | — | 76,581.45 | ||
| — | 3.00 | — | — | ||
| Supply of OC Card files, Enclosure with mounting arrangement, consisting of OC TOP & BOTTOM BACK PLANES (Two object controllers are accommodated in single enclosure) for spare purpose and for Medha Servo system.(Inspection Agency by RDSO) | — | — | — | 6,05,161.26 | |
| — | — | — | 74,01,369.11 | ||
| — | 38.00 | — | — | ||
| Wiring of central gateway into existing data logger system as per available bits in Datalogger, for monitoring of location boxes opening/closing through SMS and in control room. | — | — | — | 33,947.68 | |
| — | 1.00 | — | — | ||
| Modification/Alteration in existing EI (Electronic Interlocking) as per latest RDSO guidelines & TAN. It includes: Design and modification in existing Interface, Interlocking circuits and logic of EI system including modification in the VDU (Video Display Unit)/ LCP (Local Control panel), CCIP(Control cum Indication Panel) if any, Maintenance terminal (MTPC), Data Logger, Relay rack wiring etc. The complete work should comply with the latest RDSO specifications, guidelines and as per approved SIP & circuit diagrams. All the material (Interface cards/ relays/ wiring material/ connectors/ fuses /communication devices etc.) shall be provided by the contractor. The work includes the supply of modified Selection table, Interface Circuits, VDU/LCP, CCIP diagram if any etc. to suit the modified SIP. It also includes the carrying out of FAT, SAT or two rounds FAT (as applicable) jointly with Railways and satisfactory commissioning. All plans/drawings/circuits etc. should be prepared on Auto CAD. Soft copy including Auto CAD copy has to be supplied in pen drive and 06 sets of hard copies also to be supplied as a completion drawing. (B) Alteration in volving modification from 11 up to 20 routes. | — | — | — | 25,64,630 | |
| — | 2.00 | — | — | ||
| Alteration involving modification more than 20 routes. Note: 1. Rate up to 20 Routes shall be taken as per SCH-B SN-2 Above, alteration in routes more than 20 shall covered with this item. | — | — | — | 2,56,463 | |
| — | 1.00 | — | — | ||
| Development and preparation of SIP, SWRD/GWRD,SWR etc based on existing GAD/SIP/ESP .(For station/LC upto 4 lines) Job= Per stn/LC | — | — | — | 24,130.6 | |
| — | 1.00 | — | — | ||
| Fabrication, supply, installation and fixing of SWRD/cabin diagram on good quality waterproof board of size 1500 mm(min) x 700 mm(min), thickness of board shall be 12 mm (min). Th e work shall be done as per instructions of Rail way site incharge. | — | — | — | 7,136.55 | |
| — | 200.00 | — | — | ||
| Drawing of wiring circuit in A-3 size sheet in autocad.(02 sets photo copy & 01 set tracing with soft copy) | — | — | — | 1,40,966 | |
| — | 1.00 | — | — | ||
| Preparation & submission of cable route plan of main & tail cables , cable corage plan, location particulars, CT rack particulars, meggering report , earth resistance particulars, traction bonding diagram and any other drawing / particulars required in auto CAD in minimum A3 size each sheet should have a block for signature of Railway officials as well as block for signature of the firm, where signature shall be put up by the authorized signatory of the firms. The name of the work as given by the Railway shall be written on every sheet under the work column. One compete set of tracings and four sets of copies of complete above detailed particulars / drawing along with one CD to be supplied by the contractor in thick plastic folders. | — | — | — | 32,561.3 |
Tap a document below to read it instantly. You can also download everything as a ZIP if you prefer.
details.html
HTML
nit.pdf
NIT
SIPSTHOULIPANIHARLOOPLINEGSU_V3-Model.pdf
ATTACHMENT
Tenderbookletsithouli.pdf
ATTACHMENT
IRGCC2022_1.pdf
ATTACHMENT
IRGCC2022ACS1_1.pdf
ATTACHMENT
IRGCC2022ACS2_2.pdf
ATTACHMENT
IRGCC2022ACS3_3.pdf
ATTACHMENT
IRGCC2022ACS4_1.pdf
ATTACHMENT
IRGCC2022ACS5_1.pdf
ATTACHMENT
IRGCC2022ACS6_1.pdf
ATTACHMENT
IRGCC2022ACS7_1.pdf
ATTACHMENT
2021Tele523part13425647.pdf
ATTACHMENT
Annexure-VandAnnexure-V_A_.pdf
ATTACHMENT
AdvanceCorrectionSlipNo.8ACS-8.pdf
ATTACHMENT
AdvanceCorrectionSlipNo.9ACS-9.pdf
ATTACHMENT
AdvanceCorrectionSlipNo.10ACS-10.pdf
ATTACHMENT
GeneralConditionsofContractApril2022AdvanceCorrectionSlipNo_11.pdf
ATTACHMENT
AllannexuresNew52.pdf
ATTACHMENT
Download all tender documents and submit your bid
Disclaimer: TenderKart has made every reasonable effort to ensure that the information on this page is accurate and authentic, however it cannot be held liable for any third-party claims or losses or any damages. TenderKart makes no warranty, expressed or implied, as to the results obtained from the use of this information. If you notice any error or omission, please let us know at .