Loading…
India Infra Updates on WhatsApp
Join the Tenderkart WhatsApp channel for India Tender Updates
Loading…
Tender ID
Eligibility, documents, scope and key termsEligibility, required documents, scope of work and key terms of this tender, in one click.
| # | Company | Amount | Rank | Status |
|---|---|---|---|---|
| 1 | L1₹22.7 LAccepted-AOC 37 222 BUNDU KATRA AGRA UP | AGRA | UP | L1 | Accepted-AOC L1 | |
| 2 | L2₹24.2 L+₹1.3 L (5.85%)Rejected-AOC | L2 | Rejected-AOC L2 |
Tender Value
₹24.3 L
EMD Value
₹48,500
Closing Date
12 Jun 2023, 6:00 pmClosed
Eligibility, documents, scope and key termsEligibility, required documents, scope of work and key terms of this tender, in one click.
GE Bharatpur
Kanjoli Line Bharatpur
Addn/Altn to Bldg No P-41(Admin Block) at RMS Dholpur
2023_MES_595346_1
8242/E8
Open Tender
Civil Works
Item Rate
180 days
GE Bharatpur
As per NIT
6 documents required · 6 mandatory
₹500
GE Bharatpur
₹48,500
Yes
7 Jul 2023
13 May 2023
14 Jun 2023
13 May 2023
12 Jun 2023
29 May 2023
15 May 2023 - 24 May 2023
Amount
Taking down door /window of any description exc1 Sqm but not exc 2 Sqm each complete all as specified and directed.
Taking down chowkhats or frames area not exc. 1.5 sqm each with shutters (without taking off shutters from the frames) complete all as specified and directed.
Demolition of cement concrete (unreinforced) in ground floors and pavings n exc 15 cm thickness (below or above ground level ) and removing unserviceable material exc 100 mtr complete all as specified and directed.
Demolition of stone slabs and tiles of any description or thickness laid bedded and pointed in any mortar in floors, aprons etc complete all as specified and directed. .
Taking down cement plaster of any description on brick or stone walls or from concrete surface incl racking out joints hacking for key scrubbing with water etc complete all as specified and directed.
Dismantling, floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises complete all as specified and directed.
M&L Solid PVC door/cup board frame of size 50mm x 47mm made out of 5mm thick plain colour PVC sheet reinforced with MS square tube, as per specification and drawing given in MES SSR Pt II -2020. complete all as specified and directed.
S&F Factory made solid panel PVC door/cup board shutter 30mm thick (style) consisting of frame made out of M.S tubes for top & bottom rails. M.S frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail and bottom rail on either side and as gap insert for top rail and bottom rail. Panelling of plain colour PVC sheet to be fitted in the M.S frame welded/sealed to the stiles and rails with suitable PVC sheet beading and joined together with solvent cement, suippling and fixing in the frame at site as per specification in SSR Part-I. complete all as specified and directed.
S&F butt hinges medium grade cold rolled 100 mm mild steel and fixed complete all as specified and directed.
S&F mild steel barrel tower bolts 150 mm long, stove enamelled black with bright bolt complete all as specified and directed.
S&F Mild steel pressed handles oval type size 125 mm, stove enamelled black of complete all as specified and directed.
S&F mild steel sliding door bolt 250 mm long, plate type stove enamelled black, with bright bolt not less than 12 mm dia with the incl a min of 6 bolts and nuts four on bolt plate and two on staple plate complete all as specified and directed. .
Roughning surfaces of old concrete floor by picking , sweeping , clean and washing down with water to remove dust etc including brushing neat cement slurry with 3.00 Kg of cement per Sqm complete all as specified and directed.
M&L for screed bed or bedding layer 15 mm thick in cement mortar 1:4 mixed with water proofing liquid as per manufactur’s direction, finished even and smooth without using extra cement mixed with water proofing compund complete all as specified and directed by Engr-in- Charge.
Supply only liquid water proofing compound ISI marked complete all as specified and directed. .
M&L APP based polymeric membrane not less than 3mm thick , weighing not less than 3.5 Kg / sqm , and upper side of membrane thermally insulated with white mineral gravel finish , informly embedded during manufacturing process,shall only be used . It shall be laid by torch application .Side over laps shall be 75 mm and the end shall be 100 mm and all overlaps and joints shall be sealed by torch application including applying a coat of cold bitumen primer conferming IS:3384 @ 0.40 Kg/Sqm and applying hot blown bitumen spread per 1.2 Kg/sqm complete all as specified and directed by Engr-in-Charge.
M&L for cutting grooves in stone walls 75 mm wide and 65 mm deep and shaping horizontal face of groove with cement mortar 1:3 complete all as specified and directed.
M&L for providing PCC (1:2:4) type B0 using12.5 mm graded stone aggregate as in roof kerbs rounded or chamfered on edges or sloping of roof complete all as specified and directed.
S&F Mild steel framed work such as grills, gratings, etc. with ends of bars shouldered and/or riveted, or forged into spikes, framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; frame work of water tanks, chowkat for door and similar work confirming to Fe-290 Gde-E-165. complete all as specified and directed.
S &F Factory made 35mm thick Plain framed, panelled shutter without interlocking rail and one panel of second class hard wood,with lock rail and panel of 9 mm B.W.P. commercial ply or 12 mm veneered particle board with commercial veneering on both faces. The size of rail and stile as per IS : 1003 (Part I), kiln seasoned and chemically pressure treated, complete all as specified and directed.
M & L for rolled mild steel framed work as in doors or gates of angle or other section with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering. Doors, etc. to be prepared for hanging or sliding,with and including either hooks,and hinges or steel hanging,door fittings (exclusive of steel sheeting or other covering,running rails and guides) and,hanging; also fastening and,fixing complete all as specified and directed by Engr-in- Charge
M&L Mild steel, plain, black sheet 1.00mm thick in hearths; covering to door shutters; covering to door chowkats (frames); chullah hoods; water tanks; water troughs; ducts; urinal troughs and funnels, etc. cut to size edges beaded if directed,holes punched; including round headed screws, clout nails or rivets and fixed to wood or steel members, etc., with plain 40 mm lap joints or welded/ riveted seams including bending, turning up, mitred angles, stopped ends, outlets, etc. complete all as specified and directed.
M&L glazed ceramic coloured tiles 300 x 450 mm x7mm thick on skirting, dado set and jointed in neat cement slurry and pointed in white cement with pigment to match the surface over 10 mm thick screed in CM 1:4 complete all as specified and directed. by Engr-in- Charge.
M&L non skid ceramic coloured tiles 7 to 8mm thick (square /rectangulament ) area of each tiles exceeding 0.11 Sqm but not exc 0.18 Sqm, in floors set and jointed in neat cement slurry and pointed in white/coloured cement with pigment to match complete all as specified and directed.
M&L Vitrified ceramic tiles 10mm thick (square/rectangular) light shade area of each tile not exceeding 0.36 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match complete all as specified and directed.
M&L 15 mm thick for screed bed or bedding layer of CM 1:4 for laying floor finishes complete all as specified and directed.
M&L 20 mm thick Granite (of any type/ any colour) work (table rubbed and polished) in steps, jambs, pillars, window- cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite complete all as specified and directed.
S/F in repair Vitreous China wash down water closet pan (pedestal pattern), white (excluding fixing bolts, flushing cistern and flush pipe) complete all as specifed and directed.
S&F in repair PVC low level flushing cistern 10 ltrs capacity white with inlet ball value, float valve and handle incl brackets, PVC flush pipe complete all as specified and directed.
S&F in repair vitreous china wash basin white, flat back of size 550x400mm including 32mm dia PVC waste pipe CP brass waste coupling 32 mm dia , pair of MS angle brackets or MS fastener/ bolts for fixing arrangements/ granite counter, 450mm long pvc connection with PVC nut and washer complete at site and all as directed by Engr-in- charge.
S&F in repair Tubular towel rail Brass chromium plated, 20mmdia, D type, 60cm long between flanges. complete all as specified and directed by Engr-in-Charge.
S&F PVC connection 15 mm x 450 mm including brass check nut at both ends screwed for iron pipe of 15 mm bore complete all as specified and directed.
S&F in repair Bib tap cast copper alloy with crutch or butterfly handle, chromium plated fency type screwed for iron pipe, suitable for 15 mm bore complete all as specified and directed.
S&F in repair angle valve cast copper chromium plated screwed down, high pressure with capstan head suitable for 15 mm bore, screwed both ends for iron pipe complete all as specified and directed.
S&F in repair pillar taps, cast copper alloy, with capstan heads, chromium plated fancy type (swan neck ),screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly-nuts, screwed for iron suitable of 15 mm bore pipe and fixed complete all as specified and directed by Engr-in-Charge
S&F in repair stainless steel gratings of outer frame dia 110 mm openable type incl all necessary fittings such as hinges including embeding in tiles with white cement. complete all as specified and directed.
S&F in repair Soap dish holder (SS), any type, fixed to plugs with screws complete all as specified and directed. by Engr-in-Charge.
M&L for 75 mm thick plain cement concrete 1:3:6, type C-2 (using 40 mm graded stone aggregate) as in plinth protection including finished even and smooth without using extra cement and complete all as specified and directed by Engr-in-charge.
M&L rendering 15mm thick in cement mortar 1:4 finished even and smooth without using extra cement on external brick/stone masonry surfaces complete all as specified and directed.
M&L rendering 15mm thick in cement mortar 1:6 finished even and smooth without using extra cement on stone masonry surfaces complete all as specified and directed.
M&L rendering 5mm thick in cement mortar 1:3 finished even and smooth without using extra cement on ceilling surfaces complete all as specified and directed.
Taking up and down GI tubing of 15 mm dia and connection and incl cleaning for refixing or removal to store complete all as specified and directed.
Taking up and down GI tubing of 20 mm dia and connection and incl cleaning for refixing or removal to store complete all as specified and directed.
S&F 15 mm dia galvanized pipes medium grade with all fittings and fixed complete wall and ceiling or laid in floors complete all as specified and directed.
S&F 20 mm dia galvanized pipes medium grade with all fittings and fixed complete to wall and ceiling or laid in floors complete all as specified and directed.
Dismantling of water storage tank of any type or description and removing from site or refixing in position complete all as specified and directed.
S & F 500 ltr rotational moulded polythylene water storage tank, triple layered, (cylindrical veritical with closed top) hoisted and fixed in position all as specified in SSR Pt-I, with ball valve of 20 mm bore high pressure PTMT with epoxy coated aluminium rod and high density plastic ball, screwed for iron pipe fixed complete all as specfied and directed.
S&F in repair 20 mm bore Stop valves, cast copper alloy, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed complete all as specified and directed.
Cutting chases for concealed water tubing or concealed conduit & making good in CM 1.3 of girth exe 10 cm in stone, concrete block or slab wall etc complete all as specified and directed by Engineer-in-Charge .
S&F PVC SWR bends of 110 mm bore provided with access door complete all as specified and directed.
S&F PVC (SWR) floor trap plain including jointing with solvent cement 75 mm dia complete all as specified and directed.
S&F PVC (SWR) vent cowl 75 mm bore complete all as specified and directed.
S&F PVC (SWR) WC connector with lip ring 110 mm complete all as specified and directed.
S&F in repair PVC SWR pipes 110 mm bore single socketed in any length with rubber ring joint fixed to wall or laid in trenches or in floors with steel clamps complete all as specified and directed.
S&F in repair PVC SWR pipes 75 mm bore single socketed in any length with rubber ring joint fixed to wall or laid in trenches or in floors with steel clamps complete all as specified and directed.
M & L raking out joints pointing to random rubble or polygonal rubble, un-coursed or brought up to courses built in cement mortar complete all as specified and directed.
M&L for Raised pointing to random or polygonal rubble, un?coursed or brought upto courses in cement mortar 1:4 complete all as specified and directed.
M&L for repairing the edge / corner of Chajja / roof projection of Ground and First Floor and similar work by removing plaster width / girth exc 200 mm but not exceeding 300 mm and making good with 10 mm thick rendering in cement mortar 1:3 to match with existing surface complete all as specified and directed.
Dismantling wrought iron or Mild steel work of any description not otherwise provided for complete all as specified and directed.
Material and labour powder coated anodised aluminium frame for doors, windows, ventilators with one or more rebates including joining cleat for fixing etc. complete all as specified and directed. Note:- Minimum thickness of powder coating shall not be less than 50 micron.
S&F sliding window shutters, aluminium standard aluminium section 39.40 x 17.70 x 2.0mm (WS-4699) as in side of shutter, 39.40 x 17.70 x2.0mm (WS-4698) as in shutter inter locking, 39.40 x 17.70 x 2.0mm (WS-4697) as in shutter top & bottom, not divided into panels, including locking arrangement, necessary jointing cleats, glazing clips, rubber packing anodized aluminum holdings and screws etc, complete all as specified suitable for single glass, complete all as specified and directed. Note : Tinted glass and wire cloth shall be measured and paid separately under respective items of BOQ.
S&F for 4 mm thick , plain, tinted glass area n. exc 0.50 sqm each pane fixed in aluminium frame as in windows complete all as specified and directed.
S & F aluminium anodized grill size 75 x 75 mm spacing fixed to aluminium windows with aluminium beading complete all as specified and directed.
S & F Stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples, complete all as specified and directed.
S&F powder coated Anodised aluminium window and ventilator shutters, side hung type without sash bars, aluminium sections weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws, anodised aluminium fittings such as peg stays 150mm long (1 no.). hinges type B-21 100mm long (2 no.) suitable handle (1no.) complete all as specified and directed. Note:-Minimum thickness of powder coating shall not be less than 50 micron,
M&L 12 mm thick designer ceiling tiles of 595mm x595 mm (Make : Everest or equivalent as approved by GE) in ceiling fixed with screw as per manufactures instructions, fixed with white powder coated galvanized iron grid with 24mm wide T-section exposed flanges comprising of main runner made from 0.33mm thick galvanized steel sheet & of size T 24x32mm and spaced at 1.2m c/c securely fixed to the structural soffits by hangers at 1.2m of GI wire 4mm dia fixed rawl plug, level adjusters and screws etc. The last hanger at the end of each main runner shall not be greater than 450mm from adjacent wall flush fitting of 1200mm long cross tee with (double stitching) to be inter locked between main runners at 600mm c/c to form 600x600mm modules, angle along perimeter wall shall be of 0.45mm thick galvanized steel of size 19x19mm of white colour all as per instruction complete all as specified & directed.
Surface dressing n exc 15 Cm deep in Hard/Dense soil complete all as specified and directed.
M&L for 75mm thick PCC 1:4:8 type D2 (using 40mm graded aggregate) in sub base, floors and paving complete all as specified and directed.
Excavating in post holes (or similar holes) each n.exc 0.5 cum, getting out, returning filling in and ramming earth or broken rubble mixed with earth around in layers, n.exc 25cm and making good surface in soft/disintegrated rock complete all as specified and directed.
M & L for PCC 1:3:6 Type C2 (using 40mm graded stone aggregate) as in foundation fitting and mass concrete complete all as specified and directed.
M&L rolled mild steel work in Joist, channel, angle, or tee sections, fixed independently, without connecting plates, etc (cut to ordinary lengths i.e. within 20mm of the length indicated) of confirming to grade Fe-290 (Gde E-165) complete all as specified and directed.
Supply and fixing mild steel rolled sections as in main and cross beam, hip and jack rafters,purlins where connected to common rafters and running rails and guides for sliding dorrs, fixed with angle cleats or other connected plates confirming to grade Fe 290 (Gde E-165) complete all as specified and directed.
M&L for plain cement concrete 1:2:4 type B1 (using 20 mm graded aggregate) as in lintels upto 1.5 m clear span and other similar bands, plinth courses, string courses,parapets and railings upto 60 cm in height, copings, kneelers, apex stones bed plates, water troughs and the like including weathering, slightly rounded or chamfered anglesand throating, complete all as specified and directed.
S&F pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50 mm thick of any colour having tensile strength of 550 MPa as in roof covering / cladding to wall, molding / folding in circular / semicircular of any position and height fixed with self tapping screws complete all as specified and directed by Engr-in-charge
S&F Plain, Aluminium sheeting,0.56mm thick, Alloy 31000 H4 in ridges, hips, valley gutter, drip and straight flashing (length and girth as fixed) complete all as specified and directed by Engr-in-charge
S&F 2mm thick Fibre glass reinforced translucent corrugated sheeting with two corrugations side lap fixed with coach screw and washer in roof, wall etc complete all as specified and directed.
Providing and laying 80mm thick factory made chamfered edge cement concrete paver block of M-30 grade with approved colour, design & pattern as in footparth, parks, lawns, drive ways or light traffic parking etc., of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over and including 50mm thick compacted bed of coarse sand, compacting and proper embedding/ laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with fine sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand complete all as specified and directed.
M&L for Cutting holes exceeding one brick and not exc two bricks in stone walls in cement mortar for inserting holdfasts/angle and making good dismantled portion in cement mortar 1:3 or cement concrete 1:2:4 Type B-1 as required complete all as specified and directed.
Excavation in trenches in soft/disintigrated rock n. exc 1.5m width and 1.5m in depth and getting out complete all as specified and directed.
Returning filling including spreading levelling, watering and well ramming in layers n. exc 25cm complete all as specified and directed.
Removal of excavated soil to a distance n. exc 50m and deposited where directed n. exc 1.5m above the starting point complete all as specified and directed.
M & L for brick work with sub- class 'B' bricks, straight or curved on plan exc 6m mean radius, built in CM 1:4 complete all as specified and directed.
M&L Formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200mm thick (Horizontal or sloping) complete all as specified and directed.
M & L for formwork to edges of concrete flats, treads, breaks in floors, window cills, concrete rail?ings, openings in concrete walls, floor and roofs n exc 20 cm wide and sides of RCC/ PCC bands in walls, horizon?tal or sloping and similar work exc 10cm but n exc 20cm wide complete all as specified and directed.
M & L for mild steel TMT bars 10mm dia, and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed.
M&L for mild steel TMT bar 5 mm dia and over upto and including 10mm dia in stirrups spacers and binders complete all as specified and directed.
M & L reinforced cement concrete design mix M 25 (20 mm graded aggregate) as in slab supported on walls or as in shelvesetc complete all as specified and directed.
M & L reiforced cement concrete design mix M 25 (20 mm graded aggregate) as in beams, cantilevers, lintel etc complete all as specified and directed.
M&L for salt glazed store stoneware drain pipe of 150mm internal diameter laid in trenches and jointed complete all as specified and directed.
M&L for concrete bed to drain pipes including packing under and haunching against the sides of pipes after they are laid and tested in, cement concrete 1:4:8 bore of pipe 150 mm dia complete all as specified and directed.
Complete removal of existing treatment,washing, rubbing down and stopping of distemperd and painted surface of old surface by Electric Rotary grinder including brooming down with steel wire brushing, scrapping down smoke soot, moulds, moss and efflorscent salts and trading oil and greasy spots of Wall Surface removing of nails, making good holes , cracks etc , cleaning of floors , glasses, joinery of drops and splashes incl all arrangement necessary for execution of work, complete all as specified and as directed by Engineer-in-Charge.
M&L for preparation of existing surface by sand paper gentle rubbing to obtain smooth surfaces and applying Two coats of oil bound distempering white or tinted (copolymer based resin glue to be added for longer durability and better finish) using hand roller over 3mm thick wall care putty on Wall Surface including all necessary arrangement for execution of work ,complete all as specified and as directed by Engineer-in-Charge.
M&L for two coats painting with synthetic enamel paint to old wood or wood based surfaces of any description, not otherwise described over 10 CM width or girth including preparation of old painted surface including all preparatory work complete all as specified and as directed by Engineer-in-Charge.
M&L for two coats painting with synthetic enamel paint to old steel or steel based surfaces of any description, not otherwise described over 10 CM width or girth including preparation of old painted surface including all preparatory work complete all as specified and directed.
M&L for preparation of new plastered surfaces of wall and applying two coats of cement base paint complete all as specified and directed.
M & L Preparation of old decorated plastered or undecorated plastered surface of ceiling including cornices, pilasters etc by brooming down, steel wire brushing ,scraping down smoke soot, moulds, moss and efflorescent salts and treating oil and greasy spots and applying two coat of white wash on ceiling complete all as specified and as directed by Engineer-in-Charge.
M & L preparation of newly plastered surfaces and applying three coats of white wash in ceiling complete all as specified and directed.
M & L for preparation of new wood or wood based surface and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and directed.
M&L for preparing surfaces of any description over 10 cm girth or width, not otherwise described and applying two coats of synthetic enamel paint over a coat of Red oxide zinc chrome primer on new surfaces of steel or iron complete all as specified and directed.
Taking down carefully copper/aluminium point wiring (light, fan, socket or power) complete fittings such as switches, ceiling roses, pendents, regulators, sockets etc removing materials and making good disturbed surfaces of wall, floor & ceiling etc complete all as specified and directed.
Dismantling of old U/S rusted main switch/DB of any size capacity and make complete all as specified and directed.
Dismantling of old U/S sub main wiring and service wire of any size & make complete all as specified and directed.
M&L point wiring complete with 1.5 Sqmm 02 x single core multistranded copper conductor of 1100 volts grade PVC pre insulated FRLS and unsheathed cable enclosed in and including PVC casing and caping double locked box type with all PVC accessories such as Tee, bend, collar, elbow, square junction box etc fixed on the surface of wall/ceiling by means of PVCsleevel/dash fastners with cadmium plated screws including suitable size of PVC boards for mounting fittings like switches, sockets, fan regulator etc including 1.5 Sqmm insulated but unsheathed copper earth continuity conductor to common earth and connedcted to earth dolly complete all as specified and directed for the following :-
One light point controlled by one one way switch.
One fan point controlled by one one way switch.
One 3 pin 6 Amp socket point outlet on the same board with other switches
One 3 pin 6 Amp socket point outlet on the independent board
All as per item No 104 above but with multi stranded copper conductor cable 2.5 Sqmm size for 3 pin 16 Amps socket point outlet on independent board including 2.5 Sqmm copper cable PVC insulated FRLS unsheathed copper continuous earth wire including connecting to common earth dolly complete all as specified and directed.
S&F switch piano flush button single pole one way 6 Amps 230 volt grade complete all as specified and directed.
S&F switch piano flush button single pole one way 15 Amps 230 volt grade complete all as specified and directed.
S&F socket outlet 2 in 1, 3 pin, 5 Amp flush type multi purpose, complete all as per specified and directed.
S&F socket outlet 2 in 1, 6 pin, 15 Amp flush type multi purpose, complete all as per specified and directed.
S&F ceiling rose surface bakelite 50 x 40 mm three terminal ISI marked including suitable size of PVC board complete all as specified and directed.
S&F step type electronic fan regulator EME type 450 watt complete all as specified and directed.
M&L submain wiring complete with 4 Sqmm single core multi standred PVC insulated and sheathed cable FRLS copper conductor two runs and one run of 2.5 Sqmm copper cable for earth continuity conductor in and including drawn through PVC casing capping PVC conduit/sleeves with all PVC accessories fixed on wall, floor/ceiling etc complete all as specified and directed.
M&L in TPN DB 4 way factory made and OK tested made of sheet metal enclosure powder coated suitable for mounting MCB TPN 4way, 415V, with 200Amps rateded bus bar, double door type, including cutting wall and flushing in and making good the wall as per existing position after plastering/applying putty and distembering etc complete all as specified and directed by Engineer-in-Charge.
M&L for Distribution board factory made and tested made of sheet metal enclosure powder coated suitable for mounting the MCB 240 volt of 8 way SPN with200 Amp rated busbar 240 volts (double door type) including cutting wall and flushing complete all as specified and directed.
S&F MCB 240 volts 10 KA, rupturing capacity fixed in DB's of the undermentioned type and rating complete all as specified and directed.
MCB SP 240 volts 10-32 Amps , 10KA
MCB SPN 240 volts, 40 Amps, 10KA
MCB TPN 415V, 63Amps, 10KA
S&F innovative 20W LED batten 6500K that works automatically through motion detection with in 5 mtr range and turn off with in 30 second of non movement complete ,havells cat part no-LHEXACP7FN1W020 HSN Code 9405 or equivelent complete all as specified and directed. by engineer-in-charge
M&L batten/angle holder insulated with back plate including suitable size of PVC round block complete all as specified and directed by Engineer-in-Charge.
S&F LED bulb 14W cool day light , in-built voltage surge protection > 3.5kV, single ph, 230V, luminous efficacy 100Lm/Watt, base B22, min 3 star rated complete all as specified and directed by Engineer-in-Charge.
M& L for Earthing complete with galvanised mild steel plate electrode 600x600x6 mm thick buried directly in ground vertically (earth pit not less than 2.25 m deep below normal ground level) with the top edge of the earth plate electrode at a depth not less than 1.5m below normal ground level and including GI earth strip 32x6 mm bolted (with GI nuts, bolts & check nuts) and riveted to earth plate electrode at one end connected to metallic bodies of HT/LT equipment etc at the other and earth strip encased in and including 40mm bore GI light grade pipe with all fittings from top of earth plate electrode to body of equipment fixed with and including 32x6 mm flat iron clamps bolts, nuts and washers and including providing watering pipe 20mm bore GI Pipe electrode complete all as specified and shown in elctrical plate No 3 of MES SSR Part-I. the scope of work includes necessary excavation and earth work in any type of soil. removal of soil upto 50 metre PCC pit with precast RCC cover, charcoal/salt funnel, CI frame etc complete all as specified & directed.
NOTE :(I) The concrete pit shall be made in PCC 1:2:4 type B-O, using 12.50 mm graded crushed stone aggregate 40mm thick precast cover slab of RCC(1:2:4), type B-1, using 20mm graded crushed stone aggregate with suitable MS handle in lieu of CI cover. Reinforcement in cover shall be of 8mm dia TMT bars @ 150mm c/c both ways. (ii) Quoted rate deemed to be included the cost of 7.5 metre GI pipe for protection of earth strip. (iii) Quoted rate deemed to be included the cost of 7.5 metre earth lead strip. (iv) Earth electrode shall be surrounded by adequate quantity of charcoal dust and salt to a packed thinkness of 15 cm on all sides.
Supplying and laying of GI tube medium grade complete including fittings of sizes 40mm dia complete all as specified and directed.
Supply, laying, testing & commissioning LT XLPE insulated armoured (heavy duty) electric cable with stranded aluminium conductor 1100 volts grade (ISI marked) & laid inside the existing pipes or fixed on pole/wall with GI clamps and clips of the following sizes:-
10 Sqmm 2 core
35 Sqmm 3 1/2 core
S&F exhaust fan 300mm sweep dia, turbo force SP, 1400 RPM, single phase, 230V with complete accessories including cutting/pinning/demolition of any type of wall upto the required size of exhaust fan, make good the wall after fixing the exhaust fan as per existing position including plastering, applying putty and wall painting/distembering etc and making provision of wire mesh for the protection of interior area from insects/monkeys or any ruptiles including taking down of old exhaust fan etc. complete all as specified and directed. by Engineer-in-Charge.
Excavation in trenches not exc 1.5 m in depth and not exc 1.5 m wide for taking out/laying HT/LT UG cable, Fibre Optic Cable etc and getting out in soft disintegrated rock complete all as specified and directed.
Removing excavation soil at a distance not exc 50 m and deposited where directed complete all as specified and directed
Returning,filling in including spreading, leveling, watering and well ramming in layers not exc 25 cm complete all as specified and directed
Supply & laying unburnt locally available bricks class B for Cable protection suitable for LT UG cable of standard size complete all as specified and directed by Engr-in-Charge
M & L for dry sand cushioning for protection of under ground cable( 8Cm before laying the cable and 15 CM after laying the castle in trenches) complete all as specified and directed. Note : Punned thickness shall be measured.
Supply and fixing ceiling fans complete with blades, down rods, electronic regulator and accessories, 230 V, 1200mm sweep copper winding. Min air delivery 210 CFMwith service value 6.00 BEE. Five star rated with brushless direct current motor(BLDC) complete all as specified and as directed
supply and fix gate valves 20mm, cast copper alloy, screwed down,high pressure,with crutch or butterfly handle, screwed bothends for ironpipe or forunions and fixed complete all as specified and directed by engineer-in-charge
S&F Desert cooler ,electric driven (single phase)having nominal air flow capacity of 5000 cu.m per hours(or nearest size).plastic body/ PVC body) of desrt cooler 690X690X1020mm with motor of make khethan/crompton complete all as specified and directed by Engineer-in-Charge
Supply and fixing LED street light fitting 70 Watt 230 V AC outdoor type with high pressure diecast aluminum hosing and heat resistant complete with driver, lamp bracket with impact and corrosion resistant including thermal management in multiple optics complete with IP 65/66 protection complete all as specified and directed by engineer-in-charge
Supply and install water cooler fully stainless steel body of storage capacity 120 Ltrs, cooling capacity 60Ltr/Hr, 240V, 50Hz, single phase, 5 star rated, reciprocating oil cooled compressor, Copper condenser coil and copper wound compressor, (rate including voltage stabilizer of suitable capacity) colour as approved by GE and complete all as specified and as directed by Engineer-in-Charge. Note : Quoted rate deemed to be included voltage stablizer of suitable capacity.
Supply and lay GI tubing medium grade on trenches/walls of size 20mm dia with including all kind of GI fittings for making new connection of water supply from distribution mains inclusing cutting/ferrule etc Complete all as specified and as directed by Engineer-in-Charge.
M/S MAKHIJA TRADERS
stage.html
html • 0.04 MB
tech_bid_open.pdf
tech_eval.pdf
fin_bid_open.pdf
boq_comp_chart.xlsx
xlsx
fin_eval.pdf
aoc.pdf
Tap a document below to read it instantly. You can also download everything as a ZIP if you prefer.
details.html
html • 0.03 MB
Download all tender documents and submit your bid
Disclaimer: TenderKart has made every reasonable effort to ensure that the information on this page is accurate and authentic, however it cannot be held liable for any third-party claims or losses or any damages. TenderKart makes no warranty, expressed or implied, as to the results obtained from the use of this information. If you notice any error or omission, please let us know at .