Repair/replacement of joinery, toilet repair, tiling, plastering, false ceiling and certain allied works in new project area at AF Stn Nal under GE (AF) Nal

Amount

Demolition of RCC of any description and in any position not otherwise specifically provided for (reinforcement cut as required to facilitate demolition) complete all as specified and directed.

Material and labour reinforced cement concrete 1:2:4, type B-1 (nominal mix) using 20 mm graded crushed stone aggregate as in slabs supported on walls, beams, coloums, shelves and the like complete all as specified and directed. Note: Reinforcement shall be measured and paid for separately

Material and labour reinforced cement concrete 1:2:4, type B-1 (nominal mix) using 20mm graded crushed stone aggregate) as in chajjas at approx 3.00 to 7.00 meter height complete all as specified and directed (Reinforcement shall be measured and paid for separately). Note :- (i) All scaffolding and necessary arrangement for casting at specified height shall be arranged by the contractor and incl in the quoted rate

Use and waste of Formwork to soffits of suspended slab such as roof slab, floor slab, landing and similar work; flat rough finished surfaces of concrete complete all as specified and directed..

Use and waste of Formwork to soffits of suspended slab such as in chajjas at approx 3.00 to 7.00 meter height; flat rough finished surfaces of concrete complete all as specified and directed..

Use and waste of formwork to edges of concrete flats, treads, slabs, floor and roofs n exc 20 cm wide and sides of RCC/ PCC bands in walls, horizontal or sloping and similar work exc 10 cm but n exc 20 cm wide, complete all as specified and directed.

Material and labour mild steel TMT bars 10 mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia. or securing with clips complete all as specified and directed.

M&L for cutting grooves in brick wall, 75 mm wide and 65 mm deep and shaping horizontal face of groove and making good cement mortar 1:3 complete all as specified and directed.

Demolition of cement concrete in ground floors and pavings exc 15cm thick above GL and removing the rubbish outside MoD land complete all as specified and directed.

M&L 75mm thick PCC 1:3:6 type C-2 (using 20mm graded aggregate) as in plinth protection laid in alternet bays, surfaces finished even & smooth whtiout using extra cement including making joints complete all as specified and directed.

M&L 75mm thick PCC 1:4:8 type D-2 (using 40mm graded aggregate) as in sub base of floor surface finished even rough to receive floor topping complete all as specified and directed.

M&L 25mm thick PCC 1:2:4 type B-0 (using 12.5mm graded aggregate) as in sub base of floor surface finished even rough to receive floor topping complete all as specified and directed.

M&L 20 mm thick plastering/ screed bed or bedding layers in CM 1:4 brick/ concrete surfaces as in sunkan floor mixed water proofing compound as per manufactures instruction even and smooth without using extra cement (WPC measured and paid seperately) complete all as specified and directed.

M&L for applying a tack coat of industrial bitumen 85/25 grade at the rate of 1.2 kg per sqm in sunkan floor portion incl preparation plaster concrete surface complete all as specified and directed.

Supply only integral water proopfing compound complete all as specified and directed.

S & F in repair 40 mm bore 600 mm long spout for draining the surlplus water from the sunken floor portion incl cutting holes and making good the disturbed surface in Cement mortar 1:3 or PCC 1:2:4 complete all as specified and directed.

M&L PCC 1:4:8 type D-2 (using 40mm graded aggregate) as in mass concrete as in sunken floor, complete all as specified and directed.

M&L PCC 40mm thick 1:2:4 type B-1, (using 20mm graded stone aggregate) as in floors & finishing the surface even & smooth using extra cement complete all as specified and directed.

S&F glass dividing strips 3 mm thick and 38 mm wide inserted in position conform to design complete all as specified and directed.

Dismantling floor, hearth or wall tiling incl cement mortar bedding (but not backing) and rubbish off the premises complete all as specified and directed. Note:- The demolished material should be disposed off out side the MOD land. The contractor shall quote his rates considering the above element

Material and labour Glazed ceramic coloured tiles 7 to 8mm thick (Square/rectangular ) dark/printed in vertical surface area of each tile exceeding 0.13 sqm but not exceeding 0.18 sqm thick set & jointed in neat cement slurry and pointed with coloured cement to match, over and including 10mm thick rendering in CM 1:4 complete all as specified and directed.

Material and labour non-skid, ceramic, coloured tiles 7 to 8mm thick (Square/rectangular) area of each tile exceeding 0.13 sqm but not exceeding 0.18 sqm, in floors, set and jointed in cement slurry and pointed in white or coloured cement to match with the shade of tiles laid over and including 15mm thick screed bed or bedding layer in cm 1:6 as specified and directed.

Material and labour non-skid, ceramic, coloured tiles 7 to 8mm thick (Square/rectangular ) area of each tile exceeding 0.13 sqm but not exceeding 0.18 sqm, as in skirting, set and jointed in cement slurry and pointed in white or coloured cement to match with the shade of tiles laid over and including 10mm thick backing coat on fair faces of brick work or concrete surface in CM 1:4 complete all as specified and directed.

Dismantling of stone slab and tiles of any descriptoin or thickness in floors aprons etc, laid bedded and pointed in any mortar complete all as specified and directed.

Material and labour 18 to 20 mm thick granite (of any type) work (table rubbed and polished) in steps, landings, window cills cooking plate form and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite laid over and including 15mm thick screed bed or bedding layer in cm 1:6, and incliding rounding of edges of granite slabs 10 to 20 mm thick by grainding and rubbing and finished smooth, coloured as approved by GE all as specified and directed. Note: Front facia edges of granite slabs shall be rounding and finished smooth. The contractor shall quote his rates considering the above element, no extra shall paid on this account.

All as per description of serial Item no. 25.00 here in before but as on vertical surfaces and over 10 mm thick rendering in CM 1:4.

Taking down cement plaster on brick or stone walls/ceiling etc including racking out joints, hacking for key, scrubbing down with water etc complete all as specified and directed. Note :- The demolished material should be disposed off outside MoD land. The contractor shall quote his rates considering the above element, no extra shall paid on this account

Demolition of brick or stone masonary built in cement morter incl all quions, arches, pillar etc. complete all as specified & directed.

Material and labour brick work with sub class -B bricks old size, straight or curved on plan exc 6m mean radius built in CM 1:6. complete all as specified & directed.

All as per description of serial Item no. 29.00 here in before but as in half brick thick wall built in CM 1:4.

Material and labour for repairing of soffits of slabs and similar works by dismantling of loose/ disintegrated portion of RCC at any height and in any sitution, including provn of support, formwork and welding of reinforcement and fixing in position and with provision of weld mesh, applying dubbing 1st coat of 20 to 25mm thick in CM 1:3 finished rough and finishing coat of 10mm thick in CM 1:3 finished even and smooth without using extra cement over and including cement slurry @ 3 kg/sqm, finished even and smooth to desired shape and applying two coats of weather proof exterior emulsion paint over a coat of arylic resistant primer to match with existing surfaces complete all as specified and directed.(weld mesh measured and paid sepatrtely) Note:- (i) Unit rate of this item includes the cost of scaffolding, formwork etc. and nothing extra shall be paid on account of variation in height. (ii) For payment purpose, the area of finished plaster in 2nd coat shall be considered.

Material and labour for Hard drawn steel wire fabric (weld mesh) of weight not less than 3 kg/ sqm and not exc 4 Kg/ sqm cut to lengths, bent to shape required and tying with and including mild steel wire (annealed) not less than 0.9mm in dia supplied and fixed in reinforcemnt complete all as specified and directed.

Material and labour 15mm thick rendering on other than faces of brick work or concrete surface in cm 1:6 to be finished even and smooth without using extra cement complete all as specified and directed.

Material and labour 10mm thick rendering on concrete surface in cm 1:3 as in ceiling surface to be finished even and smooth without using extra cement complete all as specified and directed..

Material and labour 15mm thick rendering on fair faces of brick work or concrete surface in cm 1:4 to be finished even and smooth without using extra cement complete all as specified and directed.

Material and labour two coats of white wash on newly plastered surfaces of wall including preparation of surfacs complete all as specified and directed.

M&L for Preparing surface of new plastered surface and applying two coat of oil bound distemper emulsion over one coat of primer complete all as specified and directed.

Material and labour three coats of white wash on newly plastered surfaces of ceiling including preparation of surfaces complete all as specified and directed.

M&L for Preparing surface of new plastered surface and applying two coats of acrylic emulsion exterior paint over one coat of primer, tint as approved by GE in camoflauge pattern to match existing surface complete all as specified and directed.

Material and labour preparation of plastered or unplastered old decorated surfaces of walls including brooming down or steel wire brushing; scrapping down smoke soot, moulds, moss and efflorescent salts and trading oil and greasy spots as required, and applying one coat of white lime wash complete all as specified and directed.

All as item No 40 above but as in ceiling.

Material and labour preparation of plastered or unplastered old decorated surfaces of walls including brooming down with steel wire brushing scrapping down smoke soot moulds moss and efflorescence salts and trading oil and greasy spot including washing, rubbing down and stopping the connected previously treated surfaces and applying one coat of oil bound distemper emulsion complete all as specified and directed.

Taking down chowkats or frames but with shutters (with out taking off shutter from the frames) not exc 1.5 sqm each complete all as specified and directed.

Taking down chowkats or frames but with shutters (with out taking off shutter from the frames) Exc 1.5 sqm but n. exc 4 sqm each complete all as specified and directed.

Taking down shutters of any description exc 1sqm but n. exc 2 sqm each complete all as specified and directed.

Supplying & fixing 1.25 mm thick Pressed Steel door frames size 105x60mm for doors with one or more rebates inclding necessary fixing lugs, hinges, lock strike plate, etc including filling back hollow with PCC 1:3:6 type C-0 using 12.5 mm graded stone aggregate complete all as specified and directed.

Supplying & fixing 1.25 mm thick Pressed Steel door frames size 125x60mm for double doors with one or more rebates inclding necessary fixing lugs, hinges, lock strike plate, etc including filling back hollow with PCC 1:3:6 type C-0 using 12.5 mm graded stone aggregate complete all as specified and directed.

S&F Mild steel framed work as in door / cup board frames etc including necessary cutting, welding,drillings holes and fixed in position, all as specified and directed.

Supplying & fixing solid PVC door frames of sizes 50mm x 47mm made out of 5mm single side prelam PVC sheet used instead of plain colour PVC sheet & edges will be painted to match with prelam sheet reinforced with MS Square tube complete all specified and as directed.

S & F factory made solid panel PVC door shutter 30mm thick (style) consisting of frame made out of M.S. tubes for top and bottom rails. M.S. frame shall be covered with heat moulded prelam PVC "C" channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and prelam colour PVC sheets for top rail , lock rail and bottom rail on either side and as gap insert for top rail and bottom rail , both side prelam PVC sheet used insted of plain colour PVC sheet. Stile and rail feathered at edges paneling of prelam solid sheets 10 mm thick to be fitted in the MS framewelded, sealed to the stiles and rails with suitable PVC sheet beading , and jointed together with solvent cement complete all as specified in SSR Part -II and directed.

M & L for providing cupboard shutter in required size at site made out of 18 mm thk PVC colour sheet and provision of shutters one side decorative pre laminated PVC sheet and all required brackets SS screws etc. The pannels shall be fabricated using adhesive and screws where required. All the edges shall be covered with 2 mm thk edge bonding tape or 90 degree edge bent finish complete all as specified and directed.

S & F factory made Glazed & Skeleton shutters 35mm thick open rebated & prepare to received glass, gauge etc edges of framing plain chamfered or rounded in window, ventilator etc are provided with stiles and rails in 2nd class hard wood complete all as specified and directed.

S&F factory made wooden door 35 mm thick 2nd class hardwood, Plain, framed, panelled shutters (any number of panels), in with panels of timber flat on both sides (feather edged), of 12 mm BWP commercial ply with commercial veneering on both faces; supplied and fitted to chowkats complete all as specified and directed.

S&F factory made box type steel window 1.25mm thick ERW hollow P section of each frame size 60mmx25mm including grill using 10 sqmm bar double rebated both guage and glass shutter comprised gaused glazed & Skelton shutter ERW section 50mmx20mm & 1mm thick with two openable leaf consisting of two number sash bars of T-Section 20mmx3mm complete welded to frame with one vertical mullion of ERW box type T-Section of size 60mmx25mm and 1.25mm thick with following fittings welded to the frame shutter :- i) Hold fast 150mm long mild steel flat iron 12x3 mm made to shape- 04 Nos per window. ii) Handle of Z section 20mmx25mm, 100mm long – 01 No per leaf. iii) MS tower bolt 150mm long 2 No per leaf. iv) Z section 20mmx25mm, 100mm long stopper – 01 Nos per leaf. v) Cleat 55 mm long of solid square 15x20x.63mm square - 01 Nos per leaf vi) MS pintal hinges 12 x 75 mm - 2 Nos each leaf vii) 10 mm squre guard bar @ 10 cm c/c viii) 25 x 3 mm flat iron for joint of both frame wiremesh & Glazed welded inner side and outer side of frame (ix) 0.36 mm nominal dia of stainless steel wire mesh and average width of aperture 1.40 mm fixed in glazed/gazed skelton shutterof window (x) 3mm thick sheet glass ordinary quality and with oil putty in squre n exc 0.50 sqm in each pane fixed in glazed /guage skelton shutter of window xi) Fabrication and fixing arrangements as per specification including taking down, cutting holes and making good dismantled portion in PCC 1:2:4 type B-1 /cement plaster 1:4 as require and make finish good to the existing surface complete all as specified and directed. Note: (i) Windows shall be povided as per the TD of Chief Engineer Chandigarh Zone, TD-219 i.e typical details of Box window (Steel) with fly proof shutter. (ii) The mode of measurement shall be only one for the set of two i.e wire mesh window and glass window at one location and nothing extra shall be measured on this account.

S & F mild steel box type ventilator fixed type with glazing bar with mesh & glass all as per item ser No 54 above

Material and labour for surfaces of any description not other describe over 10cm width or girth and applying two coat of synthetic enamel paint over one coat of pink primer, including preparation of new wooden surface complete all as specified and directed.

Material and labour for surfaces of any description not other describe over 10cm width or girth and applying two coat of synthetic enamel paint over one coat of red oxide, including preparation of new steel surface complete all as specified and directed.

Taking down shutters of any description exc 1sqm but n. exc 2 sqm from chowkat and re-fixing in same opeing after re-securing or easening and adjusting including repair complete all as specified and directed.

Supply and fixing Mild steel butt hinges medium weight, cold rolled, 100mm, ISI marked, fixed with stainless steel screws complete all as specified and directed.

Supply and fixing 150mm long aluminium anodised barrel tower bolt, extruded section,fixed with stainless steel screws complete all as specified and directed.

S&F in repairs Mild steel handle for Steel window of size 150mm length fixed with nut and bolts or screw suitable for existing provisionscomplete all as specified and directed.

Supply and fixing in repairs Mild steel peg stay size 250mm length fixed to Steel window with nut and bolts or screw suitable for existing provisions complete all as specified and directed.

Supply and fixing 100 mm size extruded aluminium alloy handels fabricated type, anodised fixed with stainless steel screws complete all as specified and directed.

Supply and fixing 150 mm size extruded aluminium alloy handels fabricated type, anodised fixed with stainless steel screws complete all as specified and directed.

Supply and fixing 300mm aluminium alloy, anodised sliding door bolt with hasp staple (bolt type) fixing clips of sheet, cast or extruded setions and fixing bolts and sliding bolts of extruded section or cast aluminium alloy and fixed with stainless steel screws complete all as specified and directed.

Supply and fixing 150mm long Hasp and staple stainless steel sefty type bright including bolt to hinge plate and fixed with fixed with stainless steel screws complete all as specified and directed.

Supply and fixing in stainless steel wirecloths 0.45 mm nominal dia of wire and average width aperature 1.40mm and fixed with stainless wire staples complete all as specified and directed..

All as per description of serial Item no. 67.00 here in before but as in repairs.

Supply and fixing 140mm long floor door stoper of aluminium alloy body and toungue, anodised wirh hard drawn steel spring,fixed to door shutter fixed with stainless steel screws complete all as specified and directed.

Hacking out old broken glass (any thickness size quality or description) from wooden frames or stone, concrete or brick surrounds glazing with putty or fixed with beads and S&F 3.0mm thick sheet glass ordinary quality and glazing with oil putty in square n exc 0.50 Sqm in each panes complete all as specified and directed.

Supply & fixing as in repairs curtain rod stainless steel grade (SS-304) of 22-25mm bore with fixing heavy duty brackets, and ornamental type ends/ nobs etc of approved quality, complete all as specified and directed complete all as specified and directed.

S&F in repair mild steel 300mm, ordinary rat tail rod pattern springs, including roller and roller plate complete all as specified and directed.

Taking up or down 15 mm dia steel tubing & connections including clearing for refixing or removal to store complete all as specified and directed.

All as per description of serial Item no.73.00 here in before but 20mm bore tubes.

S & F 15mm bore of tube medium grade galvanized with all fittings & fixed complete to walls & ceiling or laid in floors complete all as specified and directed.

All as per description of serial Item no. 75.00 here in before but 20mm bore tubes.

Cleaning and removing all scale and dirt from RCC / PVC tank capacity of tanks exc. 250 ltrs and up to 500 ltrs by emptying, drying, cleaning with chlorine/washing powder by scrubbing the dust with wire brush from tank by removing inlet and outlet pipe and refixing inlet and outlet pipe with new tank connection fitting in the same position after cleaning and marking the date of cleaning on the tank with paint complete all as specified and directed. Note:- "Writing "CLEANED ON DD/MM/YY" on service water tank with letters or figures (Block. Roman) of size 5 cm high and min 5cm wide each.

Dismantling water tanks any type of capacity Exc 250 but n.exc 500 liters complete all as specified and directed.

S&F 500 liter capacity Rotational moulded polyethylene water storage tanks (cylin-drical vertical with closed top) tripple layered white, hoisted and fixed in position, including 20 mm bore Ball valves high pressure of PTMT with epoxy coated aluminium rod and high density plastic ball screwed for iron pipe complete all as specified and directed.

S&F 20mm PTMT nipple suitable for HDPE water tank (minimum weight 45gms) complete all as specified and directed.

S&F in repair PVC (PTMT) float valve, high pressure of PTMT with epoxy coated aluminium rod & high density plastic ball screwed for iron pipe and fixed suitable for 20mm bore pipe, complete all as secified and directed.

S & F in repair long body stop valve 15mm bore fancy type chromium plated screwed down high pressure, with crutch or butterfly handle screwed both ends for iron pipe or for unions complete all as specified and directed.

S&F in repair 15mm bore long body Angle cock fancy type chromium plated screwed down high pressure complete all as specified and directed.

S & F in repair long body stop valve15mm bore fancy type chromium plated with long shank and cup(concealed type) screwed down high pressure, with crutch or butterfly handle screwed both ends for iron pipe or for unions complete all as specified and directed.

S&F in repair 15mm long body bib taps long shank cast copper alloy with crutch or butterfly hadle secrwed for iron piper or for brass ferrule complete all as specified and directed.

S&F in repair 15 mm Pillar taps long body fancy type with capasten head chromium plated screwed down high pressure with without lettered 'Hot' or Cold with long screwed shanks and fly nuts screwed for iron pipe and fixed complete all as specified and directed.

S&F in repairs 15mm bore PVC connection pipe 600mm long with PTMT nuts at both ends complete all as specified and directed.

S &F in repair chromium pated shower rose 125mm size with or without swivel joints, any size including fixing to 15 mm bore steel pipe or union complete all as specified and directed.

S & F in repair towel rail 20mm dia chromium plated including 600mm long including brackets, screws and wooden/plastic cleats complete all as specified and directed.

S&F in repairs 75 mm dia Stainless steel with hole grating complete all as specified and directed.

S&F in repairs waste down pipe 32/40mm bore for wash basin/sink complete all as specified and directed.

S& F in repair vetrious china squatting pan orissa pattern size 630x450mm white, with intergal foot rests excluding flushing cistern and flush pipe but including traps as reauired complete all as specified and directed.

S & F in repair 10 Ltr capacity PVC valveless syphonic action type flushing cistern low level white with inlet ball valve and brackets, float and handle, L-Bend complete all as specified and directed.

S&F in repairs vitreous china wash basin, white, flat back, size 580x450mm excluding taps waste, chain and plug and porcelain stopper but including bracket complete all as specified and directed.

Demolition up to 100/75mm bore and breaking up drain pipes (AC/reinforced concrete/salt glazed ) complete all as specified and directed

S & F 110mm bore PVC SWR Pipes single socketed, in any length with rubber ring joints, fixed to walls complete all as specified and directed

S & F 75mm bore PVC SWR Pipes single socketed, in any length with rubber ring joints, fixed to walls complete all as specified and directed

S & F 110mm bore PVC SWR Junction single (Single T) equal or unequal complete all as specified and directed

S&F PVC (SWR) bends of 110 mm bore complete all as specified and directed

S&F PVC (SWR) bends of 110 mm bore with access door complete all as specified and directed

S&F PVC (SWR) 110mm bore Junction (single T) equal or unequal complete all as specified and directed

S&F PVC (SWR) bends of 75 mm bore complete all as specified and directed

S&F PVC (SWR) bends of 75 mm bore with access door complete all as specified and directed

S&F PVC (SWR) bends of 110 mm reducers complete all as specified and directed

S&F PVC (SWR) bends of 75 vent cowl with access door complete all as specified and directed

S & F in repair 75mm bore PVC (SWR) floor trap,with grating plain/ whole including jointing to waste pipe fixed in cement concrete type B-1 (1:2:4) complete all as specified and directed.

S&F as in repair stainless steel plate rack, made out of 0.80mm thick of size 0.78m x 0.92m x 0.25 m complete all as specified and directed.

S&F in repair sinks made of stainless steel 1mm thick kitchen or laboratory with plugs, washers and wastes including bedding in cement mortar on to dwarf wall or including fixing cantilever brackets and connecting union to pipe overall size 495mmx420mm bowl size 410mmx330mmx160mm complete all as specified and directed

S&F in repair stainless steel 32mm waste coupling suitable for stainless steel sink along with grating complete all as specified and directed.

Vijay Enterprises

M/S BUDHRAM BISHNOI

M/s Sharafat Farook