SPL REPAIR TO BLDG NO P-21/05 AT 3rd LANCER LINE AND PROVN OF SEWAGE LINE AND SOAK WELL WITH OUTLET PIPE UNDER GE GWALIOR

Amount

Demolition of cement concrete (unreinforced) in ground floor and paving not exceeding 15 cm thickness (below or above ground level) incl the disposal upto 50M complete all as specified and directed.

Demolition of Reinforced Cement Concrete (Existing RCC water tank, kitchen shelves etc) of any description and in any position not otherwise specifically provided for complete all as specified and directed

Dismantling floor, hearth or wall tiling of any description and in any position including cement mortar bedding (but not backing) complete all as specified and directed.

M & L for Reinforced cement concrete (nominal mix) in type B1 1:2:4 (20mm graded aggregate) Slab supported on walls, beams and columns in floors, roofs, landing, balconies, desk slabs and in Kitchen shelves and like including form work complete all as specified and directed.

M&L for mild steel TMT bars ,10mm dia and over, cut to length bent to shape required including cranking bending spirally for hoping for coloumns hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia or securing with clips quality complete all as specified and directed.

M&L for 25 mm thick cement concrete type B0, 1:2:4 (using 12.5mm graded stone aggregate) as in leveling course complete all as specified and directed.

M&L for non - skid ceramic tile coloured 7 to 8 mm thick (square/rectangular) area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm, in floor etc set and jointed in neat cement slurry and pointed in coloured cement to match, including 15mm thick screed bed in CM 1:6 complete all as specified and directed.

M&L for non - skid ceramic tile coloured 7 to 8 mm thick (square/rectangular) area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm, on vertical surface such as skirting, dados and risers to steps etc set and jointed in neat cement slurry and pointed in coloured cement to match, laid over and including rendering 10 mm thick on fair faces brick work or concrete surface in cement plaster 1:4 complete all as specified and directed.

M&L non skid ceramic coloured tiles 7 to 8mm thick (square/rectangular) area of each tile exceeding 0.06sqm but not exceeding 0.11 sqm in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match with the colour of tiles, over screed bed or bedding layer 15 mm thick of cement mortar 1:4 complete all as specified and directed.

M&L for glazed ceramic coloured tiles in vertical surface 350mm x 250mm x 7mm/ 450 x 300 x 7 mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match, aid over and including rendering 10 mm thick on fair faces brick work or concrete surface in cement plaster 1:4 complete all as specified and directed.

Taking down cement or cement lime plaster, any description on brick or stone walls, etc. including raking out joints, hacking for key, scrubbing down with water, etc complete all as specified and directed.

Demolition of Brickwork or stone/ boulder masonry, built in cement mortar or cement lime mortar including all quoins, arches, pillars, etc, but excluding ashlar facings, dressed stonework and precast concrete articles complete all as specified and directed.

M&L for Brickwork with subclass 'B' bricks old size brick, straight or curved on plan exc 6m mean radius, built in cement mortar 1:6 complete all as specified and directed.

Brick work with sub class `B' bricks straight or curved on plan exc 6m mean radius, built in CM 1:4, in half brick walls.

M&L for rendering 10 mm thick on fair faces of brick work or concrete surfaces in cement plaster 1:6, finished even and smooth (without using extra lime or cement) complete all as specified and directed.

M&L for rendering 5 mm thick on faces or brick work ,concrete surfaces, in ceiling & in cm 1:3, finished even and smooth (without using extra lime or cement) complete all as specified and directed.

M&L for rendering 15 mm thick on other than fair faces of brick work or concrete surfaces in cement plaster 1:4 and mixed with WPC, finished even and smooth (without using extra lime or cement) complete all as specified and directed. Note:- WPC shall be measured & paid seperately

Supply only integral liquid water proofing compound (ISI marked) complete all as specified and directed.

M&L for preparation of new plastered ceiling surface and applying three coats of white wash complete all as specified and directed.

Material & Labour for new plastered surfaces applying two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over new surfaces.

M&L for new plasterd surface applying two coats of distemper oil emulsion white or tinted over and including a layer of 1mm thick wall care putty on wall complete all as specified and directed.

Taking down steel tubing and connection 15m bore incl cleaning for refixing or removing from site complete all as specified and directed.

Same as per item No 22 above here in before but 20 mm dia pipe complete all as specified and directed.

M&L for GI tubing 15mm dia medium grade galvanised with all fittings fixed to wall and floor complete all as specified and directed.

Same as per item No 24 above here in before but 20 mm dia pipe complete all as specified and directed.

S&F in replacement PVC (SWR) floor trap, plain with grating including jointing with solvent cement and fixed 75mm dia outlet complete all as specified and directed.

S&F in replacement 15mm bore bib taps, fancy type chromium plated cast copper alloy with capaston head handle, screwed down screwed iron pipe or for brass ferule fixed, complete all as specified and directed.

S&F, in replacement15mm Angle stop valve of CP brass any colour high pressure screwed for iron pipe or for union fixed complete all as specified and directed.

S&F in replacement PVC connection 15mm size with PTMT nuts on both ends of length 450 mm complete all as specified and directed.

S&F in replacement swivel shower of brass chromium plated of size 125mm for fixing with 15mm bore pipe complete all as specified and directed.

S&F in replacement tabular towel rail brass chromium plated, 20 mm dia, D type, 60 cm long between flanges, complete all as specified and directed.

S&F in replacement for Soap dish of CP fixed with pvc rawal plugs and screw, complete all as specified and directed.

S&F in replacement Sheet glass shelf assembly consisting of 5.5mm thick sheet glass shelf 12cm wide with chromium plated bracket guard and railing 60cm long complete all as specified and directed

S&F in replacement Stainless Steel Peg Set of 6 hooks ISI marked medium weight complete all as specified and directed.

S&F in replacement grating 100/125 mm dia of PTMT, fixed to Nahani trap complete all as specified and directed.

S&F in replacement stainless steel kitchen plate rack made out of 0.63mm thick stainless steel of size 900x750 mm including screws and wt not less than 5.00 Kg complete all as specified and directed.

S&F in replacement kitchen sinks with drainage board made of stainless steel 1mm thick with kitchen or laboratory with plug, washers, wastes, including fixing (cantilever brackets and connecting union to pipe overall size 915mm x 460mm boul size 410mm x 330mm x 160mm) complete all as specified and directed.

S&F in replacement wash hand basin vitreous china (flat back) of size 550 x 400 mm excluding taps, waste, chain and plug and porcelain stopper but including brackets cutting for and pinning in ends complete complete all as specified and directed.

S&F in replacement 32 mm waste fittings, brass chromium plated for glazed ware sinks, basins, etc. with long screwed shanks and fly -nuts, flange end bedded in red lead cement and other end fixed complete all as specified and directed.

S&F in replacement Brass CP mixer for basin mixing hot and cold water screwed down for iron pipe and fixed complete all as specified and directed.

S&F, in replacement 15 mm bore, cast copper alloy chromium plated fancy type wall mixer tap with telephonic shower(3-in-1 system) for cold & hot water wall mixer complete all as specified and as directed.

S&F for viterous china wash down water closet pan (pedestal pattern) or wall mounted white fixing bolts, excluding flushing cistern and flush pipe including Seat cover, connection to drain and to flushing pipe syphonage pipe etc and mild steel chromium plated or aluminised hinges device & CP Jet complete all as specified and directed.

S&F Health faucet (ABS body) mild steel chromium plated suitable for 15mm dia pipe with 1.25 metre long flexible and ABS wall hoock including making connection and fixing in position complete all as specfied and directed

S&F in replacement PVC flushing cistern 10 Ltrs capacity including all fitting flush pipe etc complete all as specified and directed.

Dismantling of water tank exceeding 250 Ltrs but not exceeding 500 Ltrs complete all as specified and directed.

S&F for rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top) of capacity 500 litres hoisted and fixed in position all as specified in SSR Part-I, complete all as specified and directed.

S&F in replacement Ball brass valves high pressure with polythene float and flynut complete screwed for iron pipe of 20mm bore of brass ferrule complete all as specified and directed

S&F, in replacement 20mm stop valves, cast copper alloy screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for union fixed complete all as specified and directed.

Taking down eaves gutters and rainwater pipes (any size or pattern), including all fittings, heads, shoes, bends, swan-necks, etc including cleaning or refixing or removal to Store (measured overall as fixed along the centre line over fittings and accessories), complete all as specified and directed.

S&F 110 mm PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to walls, complete all as specified and directed.

S&F 110 mm PVC (SWR) pipes single socketed in any length with rubber ring joints, laid in trenches or in floors, complete all as specified and directed.

S&F 75 mm PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to walls, complete all as specified and directed.

S&F 75 mm PVC (SWR) pipes single socketed in any length with rubber ring joints, laid in trenches or in floors, complete all as specified and directed.

S&F PVC (SWR) bends any radius, 110mm bore, complete all as specified and directed.

S&F PVC (SWR) bends any radius, 75mm bore, complete all as specified and directed.

S&F PVC (SWR) junction single (single T), equal or unequal, 110mm bore, complete all as specified and directed.

S&F PVC (SWR) junction single (single T), equal or unequal, 75mm bore, complete all as specified and directed.

S&F for 110mm dia PVC(SWR) vent cowl, complete all as specified and directed.

S&F in replacement for PVC (SWR) gully trap 125/110 mm, setting and jointing with solvent cement complete all as specified and directed.

S&F in replacement for PVC (SWR) 'P' or 'S' trap 110 mm, setting and jointing with solvent cement complete all as specified and directed.

S&F in replacement for PVC (SWR) floor trap/ Nahani trap 75mm, plain with greating including setting and jointing with solvent cement complete all as specified and directed.

Taking down chowkhat frame with shutter (without taking out shutter from the frame) n.exc 1.50 Sqm each complete all as specified and directed.

Taking down chowkhat frame with shutter (without taking out shutter from the frame) exc 1.50 Sqm but n exc 4 sqm each complete all as specified and directed.

S&F for pressed steel frame of size 125 x 60 mm for door with one or more rebates makaing necessary fixing lugs,higes, lock strike plate, etc, complete, as specified, complete all as specified and directed.

S&F for pressed steel frame of size 105 x 60 mm for door with one or more rebates makaing necessary fixing lugs,hinges, lock strike plate, etc, complete, as specified, complete all as specified and directed.

S&F for solid PVC door frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S square tube, suppling & fixing in opening as per specification complete all as specified and directed.

S&F Factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, suppling & fixing in the frame at site as per specification & drawing complete all as specified and directed.

S&F 30 mm thick Flush shutters ,soild core construction ,with block board core and plywood face panels , commercial type on both face is covered with decorative face veneer with lipping /frame to match and complete all as specified and directed.

S&F for 35 mm thick skeleton shutters of 2nd class Hard Wood for door, open rebated and prepare to receive glass, guaze, etc (without sash bars ) edges of framing plain chamfered or rounded, fitted with for securing glass etc, size of members of shutters as specified in SSR Pt-I, section 8, clause 8.24(a), but divided into squares, with plain, chamfered or rounded, mitred and rebated sash bars, any numbers complete all as specified and directed.

S & F Box Type steel windows, Ventilator with side hung shutters (double shutters for glass and gauge) joined together with and including grills using 12 mm square bars @ 10 mm c/c as per TD No CEBZ/TD/14/2011, Sheet no -1/7 to 7/7 Including box type hinges with steel handle and steel peg stay complete with glazing bars dovetailed and welded and preparing new steel surfaces, exc. 10 cm width or girth and applying two coat synthetic enamel paint over one coat of red oxide primer etc complete all as specified.

S&F for 3mm thick, sheet glass, ordinary quality and glazing with oil putty in square not exceeding 0.5 sqm in each pane including hacking out old broken glass of any thickness and any description from wooden/ steel frame/ stone,concrete or brick surrounds complete all as specified and directed.

S&F galvanised wire cloth, .56mm nominal dia of wire and average width of aperture 1.18mm and fixed with tinned tacks or galvanised staples complete all as specified and directed

S&F, for alluminium door closer hydraulically regulated,designation No. 3, universal type, suitable for door shutters of 851 to 1000 mm in width and of weight between 61 to 80 kg and fixed complete all as specified and directed.

S&F for 150 mm aluminium anodised, barrel tower bolts of extruded section and fixed complete all as specified and directed.

S&F for extruded aluminium alloy handles 150 mm, fabricated type, anodised complete all as specified and directed.

S&F for 100 mm butt hinges, medium weight, cold rolled mild steel, and fixed complete all as specified and directed.

S&F aluminum alloy anodized sliding door bolt 300mm long with hasp and staple (bolt type) and fixing clip of sheet and cast in extruded section and fixing bolts and sliding bolt of extruded section complete all as specified and directed.

M&L for preparation of new wood or wood based surface of any description exceeding 10cm width or girth and applying two coat of synthetic enamel paint over a coat of pink primer complete all as specified and directed.

M&L for preparation of new steel surface of any description exceeding 10cm width or girth and applying two coat of synthetic enamel paint over a coat of red oxide primer complete all as specified and directed.

S&F in replacement for curtain rod of Stainless steel 23-25 mm dia pipe thickness not less than 0.8mm of pipe with fixing bracket, side nobes etc fixed on walls with screws with PVC rawl plugs etc complete all as specified and directed.

M&L for providing cement concrete type C1 1:3:6 ( using 20 mm graded aggregate) as filling inside pressed steel frame complete all as specified and directed.

Removing existing water proofing treatment (tarfelt), roughning of concrete surfaces, cleaning of concrete surfaces with water and removing debries/rubbish off materials out side of Ministry of defence (MOD) land complete all as specified.

M&L for cutting out cracks to V section in existing walls, roofing or terrace, cleaning out wetting grouting with cement and sand slurry 1:3 complete all as specified and directed.

M&L, 10mm thick rendering on top of roof surfaces of any description in cement mortar 1:4 mixed with liquid WPC @ 0.4% by weight of cement, or as per manufacturers instructions, surface finished even and smooth without using extra cement complete all as specified and directed. Note : WPC shall be measured & paid seperately.

M&L, bitumenous based primer conforming to IS-3384-1965 @ 0.40 Kg / Sqm including preparation of roof surface complete all as specified and as directed.

M&L, for APP based polymeric membrane minimum weighing 3.5kg/sqm and minimum 3mm thick reinforced with polyster non wove fabric (wt. not less than 150 gms/sqm) laid on primed surface by torch application method complete all as specified.

M&L for after laying the membrane apply coat of bituminouse aluminium paint @ 200 gm/Sqm (minimum) in two coats complete all as specified and as directed.

M&L for 75 mm thick PCC 1:3:6 type C-2 using 40mm graded stone aggrtegate as in plinth protection/path and the like including finsihing even & fair complete all as specified and directed.

M&L for 100 mm thick cement concrete type D-2 1:4:8 (using 40 mm graded stone aggregate), as in sub base for floor, finished even and rough complete all as specified and directed.

M&L for sand filling under floors or in foundations including watering and consolidation complete all as specified and directed

M&L 80 mm thickness machine pressed precast concrete interlocking paver block M-40 any shape and size confirming to IS 15658-2006 with grey cement, Coloured and pigment glossy finish rubber mould casted laid dry over sand cushioning complete all as specified and directed.

M&L for providing and laying at or near ground level factory made kerb stone of M-25 grade cement concrete in position to the required line, level and curvature, jointed with cement mortar 1:3 (1 cement: 3 coarse sand), including making joints with or without grooves (thickness of joints except at sharp curve shall not to more than 5 mm), including making drainage opening wherever required complete.

M&L for Dismantling of AC ceiling board any descrition complete all as specified and directed.

S&F for anodised aluminium snap grid frame work for false ceiling consists of powder coated aluminium angle 22x22x1.3 mm and Tee 35x25x1.3 mm of size and grid 600x600 mm complete all as specified and directed.

M&L for Non asbestos fibre cement building boards 6 mm thick fixed or laid/ inserted to Aluminium anodised frame and hanges framework fixed with Hangers 3-4 mm dia. G.I. (upto reqd length) adjusting level fixed to roof slabs by means of ceilling cleats complete all as specifed and directed

Dismantling wrought iron or mild steel work of any description not otherwise provided for, complete all as specified and directed.

S & F Framed work as in doors or gates of angle or other section with gusset plates, rails, braces, etc, complete, drilled for fixing of steel sheeting or other covering, Doors, etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails and guiders) and hanging, also fastening and fixing complete Fe 410-W (Gde-E-250) quality-A.

S&F Roof trusses (framed) trusses purlins and fastening (etc.,angle, channel) or flat section including distance pieces, MS plates/ gusset plates, cleats, hold fast etc. conforming to Gde of steel Fe 290 Gde E-165 complete all as specified and directed.

S&F rolled section as in main and cross beams, hip and jack rafters, purlins where connected to common rafters and running rails and guides for sliding doors fixed with angle cleats or other connecting plates confirming to Fe-290 (Gde E-165) complete all as specified and directed.

M&L Granite (of any type) tiles 18 mm thick machine cut, bedded and jointed with grey cement slurry and pointed with white cement with admixture of pigment to match the shade of granite stone including grinding , bull nosing and polishing complete, laid over and including 15mm thick screed in CM 1:4 complete all as specified and directed.

Excavation in trenches not exceeding 1.5 m wide and not exceeding 1.5 m in depth; for foundations etc. or for shafts, well cess pits, manholes, pier holes, etc. but not exceeding 10 Sqm on plan and getting out in soft/ loose soil complete all as specified and directed.

Demolition and breaking up drain pipes of 150 mm internal dia (Salt glazed ware, AC or Reinforced concrete) set in cement mortar complete all as specified and directed.

M&L for cement concrete (1:3:6) type C2 using 40mm graded stone aggregate in bed to drain pipe including packing under and hunching against the sides of pipes after they are laid and tested complete for pipe size of 150mm bore.

M&L for 150 mm bore Reinforced concrete pipes, class NP3, laid and jointed complete with collars.

M&L for providing cement concrete (1:2:4) type B0 (using 12.5mm graded stone aggregate) in surfaces channels drains and benching including form work and finishing fair and smooth using extra cement (forming fair finished channel shall be measured and paid for separately)

M&L for precast cement concrete (1:2:4) type B1 (using 20mm graded stone agg) as in cover slabs for man holes, drain and set in CM 1:6 including necessary from work all as specified. Note: Reinforcement and form work shall be measured paid separately)

M&L for cement concrete type B-1,(1:2:4) using 20mm graded agregate in roof kerbs or mud stops, rounded or chamfered on edges in lintels upto 1.5m clear span, cills, stes, seimic and other similar bands, plinth course, string course, lacing cours, parapets and railings upto 60cm in height, coping, kneelers, apex stones, bed plates, kerbs, water throughs and the like including wheathering slightly rounded or chamfered angle and throating including formwork complete all as specified and directed.

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exc 25 cm in loose/soft soil complete all as specified and directed.

Removing excavated material n exc. 50m and depositing where directed at alevel n exc 1.5m above the starting point complete all as specified and directed.

Cutting into existing manholes for connecting new drains of internal dia 150mm, making good to pipe and rendering, cutting out existing benching for and forming branch channel (1/2 round or 3/4 section) in cement concrete 1:2:4 type B-1 smooth finished, and reforming benching as required complete all as specified and directed.

Taking down carefully existing aluminum / copper point wiring (light, fan, socket or power point) complete of any description including fitting such as switches, ceiling roses, pendants, tube light fitting, ceiling fan with regulators, sockets, wooden boards, laminated sheets from sunken boxes, boards, shades light fitting etc and making good the disturbed surfaces of walls, floors, ceiling etc to match with existing surfaces complete all as specified and directed.

Taking down submain wiring of any size any type and in any position metalic/non metallic PVC conduit of wooden batten complete all as specified and directed.

Taking down unserviceable Sheet metal box & MCB DB SPN with MCB's of any make/capacity, complete, all as specified and directed by Engr-in-Charge.

Taking down unserviceable TPN DB with MCB's of any make/capacity, complete, all as specified and directed by Engr-In-Charge.

M&L, concealed point wiring with PVC insulated and unsheathed electric cable 1100 volts grade single core FRLSH confirming to IS 694:2010 having multi stranded copper conductor of 1.5 Sqmm nominal cross sectional area (ISI marked with valid CML No) drawn in and including concealed non metallic rigid PVC conduit medium grade( ISI marked with valid CML No) not less than 20 mm dia with all fitting and fixing accessories and 1.5 Sqmm FRLSH confirming to IS 14930 (Part-I) 2001, PVC insulated unsheathed multistranded copper conductor cable as continuous earth conductor, connected to common earth dolly by providing suitable lugs with & including pressed steel sunken terminal boxes factory made for mounting switch, regulators etc with and including 2.8 mm thick plastic laminated sheet cover (white) ISI marked, fixed with brass screws and cup washers duly painted with two coats of anti corrosive paint/black bituminous paint outside and two coats of aluminium paint inside for mounting switches sockets etc complete all as specified and directed.

One light point controlled by one switch.

One Ceiling fan point controlled by one switch.

One Exhaust fan point controlled by one switch.

One 5 pin multipurpose socket out let 5/6 Amps on the same board with other switch.

One 3 pin/5 pin switch socket outlet, 5 Amps on independent board.

Description all as per item No 116 here in before but point wiring with 2.5 sqmm FRLSH H confirming to IS 694:2010, multistrand copper conductor cable for one six pin socket outlet 15 Amps controlled by one switch on independent board and 2.5 sqmm FRLSH PVC insulated multi strand copper conductor cable as continous earth wire.

S&F switch piano, flush button single pole one way 5 Amp complete all as specified and directed.

S&F socket out let, multipurpose, 2 in 1 5 pin, 5 Amp complete all as specified and directed.

S&F switch piano, flush button single pole one way 15 Amp complete all as specified and directed.

S&F socket out let multipurpose flush type, 2 in 1 6 Pin 5/15 amps complete all as specified and directed.

S&F ceiling rose surface bakelite 63.5 mm dia three terminal complete all as specified and directed.

S&F electronic step rotary type fan regulator of two module capacity 80 to 100 Watt, 240 volts, AC 50Hz complete all as specified and directed.

S&F Lamp holder with metal ring, PVC/Polycarbonate type with back plate suitable for batten fittings ISI Marked complete.

S&F LED Lamp 09/10 watt complete with 5 star rating.

S&F Decorative ultra slim LED Tubelight fitting of LED with extruded polycarbonate, enviormental friendly energy efficient ready to use, 20 watt,4000k to 6500k as per required fitting , incluing reqd length of not less than 1.0 Sqmm PVC multistranded BIS marked 03/02 core copper conductor for electrical connection from ceiling rose to connector of LED fitting including testing on completion all as specified and directed.

S & F security light fittings better optics for uniform distribution IP 65 protection LED of 30 watt with photometric sensor, Heat resistance glass, pressure die cast aluminium housing including 25mm dia galvanised iron pipe light grade bracket bent to shape over all length 0.60mtr fixed to wall with 02 Nos FI clamps made of 40 x 5 mm FI, 15 cm long, 8 mm dia bolts and nuts with washers grouted in wall complete including reqd length of 1.5 Sqmm PVC multistranded BIS marked, 03 core copper conductor for connection from ceiling rose to light fittings incl testing on completion all as specified and directed.

Supply and fix electric water heater, storage type steel inner tank and heating element upto 2 KW capacity 25 litre, BEE 5 Star rated complete with all accessories such as safety valve, thermostate, NRV, connection piece etc all as specified and directed.

Supply and fixing ceiling fans complete with blades, down rods, electronic regulator and accessories,copper winding, 230 V, 1400 mm sweep. Min air delivery 245 CFM with service value 6.00 BEE, 5 star rated with brushless direct current motor (BLDC) completion all as specified and directed.

Supply and fix exhaust fan made of sturdy Engineering plastic complete with louvers shutter, voltage 230V, 50 Hz, RPM 1200, Copper winding of sweep 300m all as per specified and directed.

Supply & fix exhaust fans AC single phase 230/ 240 V of size 450 mm sweep copper winding with louve completion all as specified and directed.

M&L, sub main wiring with two single core PVC insulated unsheathed FRLSH confirming to IS 694:2010, multi stranded copper conductor (ISI marked with valid CML No), cable 1100 Volt grade, 6 sqmm size drawn in and including non metallic rigid PVC concealed conduit medium grade (ISI marked with valid CML No) not less than 25 mm dia with all fitting & fixing accessories including one run single core PVC insulated unsheathed 4 Sqmm FRLSH confirming to IS 14930 (Part-I) 2001, copper conductor (ISI marked with valid CML No) colour code as a earth continuity and connected upto DB complete all as specified and directed. (NOTE: (i) Two run of single core PVC cable with one run of earth conductor and conduit shall be measured as one unit and the quoted rates shall be deemed to be inclusive for cutting chases in wall/pillars/columns etc. of any description for concealing the conduits to required depth & making good the disturbed surface in cement mortar 1:4 including finishing the surface with putty to match with the existing surface.

M&L, sub main wiring with two single core PVC insulated unsheathed FRLSH confirming to IS 694:2010, multi stranded copper conductor (ISI marked with valid CML No), cable 1100 Volt grade, 4 sqmm size drawn in and including non metallic rigid PVC concealed conduit medium grade (ISI marked with valid CML No) not less than 25 mm dia with all fitting & fixing accessories including one run single core PVC insulated unsheathed 4 Sqmm FRLSH confirming to IS 14930 (Part-I) 2001, copper conductor (ISI marked with valid CML No) colour code as a earth continuity and connected upto DB complete all as specified and directed. (NOTE: (i) Two run of single core PVC cable with one run of earth conductor and conduit shall be measured as one unit and the quoted rates shall be deemed to be inclusive for cutting chases in wall/pillars/columns etc. of any description for concealing the conduits to required depth & making good the disturbed surface in cement mortar 1:4 including finishing the surface with putty to match with the existing surface.

S&F sheet metal enclosure double door for distribution board factory made for MCB DB load link VTPN 4 way suitable for MCCB as incomer, 100 Amp,4 pole & Including MCCB 100 amps 4 pole 16 KA complete. (when MCB's are to be used) with suitable size of busbar complete,fixed flush in wall including chases wall for fixing DB and making good the distributed wall surfaces to match with existing specification including taking down all as directed by Engr-in-Charge at site.

S&F MCB DB, sheet metal enclosures double door SPN 8 way with 200 Amps rated bus bar 240 volts 2 in 1 shutter type (METAL DOOR) type with blanking plates where required and IP 43 degree protection complete all as specified and directed.

S&F, MCB SPN 63 Amps, 240 volts 'C' series 16 KA ,including connection with suitable size copper lugs complete all as specified and directed.

S&F, MCB SP 240 volts,6 to 40 Amps, 'C' series 10 KA including connection with suitable size copper lugs. complete all as specified and directed.

S & F Single pole and neutral enclosure with a two pin and earth plug and socket complete with one single pole MCB 20 amp.

Supplying, laying, testing and commissioning of XLPE insulated screened PVC bedded galvanised steel strip or wire armured electric power cable (Heavy duty ) with aluminium conductor 1100 volts grade, cross sectional area size 25 Sqmm 3.5 Core.

Supplying and laying un reinforced precast concrete cable cover Class LV, Type I, flat size 250mm x 150mm x 40mm complete all as specified and directed.

Supply and fix cable jointing kit for 1.1 KV grade cable for end joint complete with Jointing material heat Shrink type and accessories suitable for 3 ½ / 4 core XLPE, armoured, Al conductor cable of size 25 to 50 sqmm,Indoor/Outdoor type

Taking out old u/s pipe line alongwith fittings from existing connections of size 25 mm dia complete all as specifies and directed.

M & L for GI pipe Med grade of 25 mm dia alongwith all fittings and fixtures complete laid in trenches all as specified and directed.

M & L for GI pipe Med grade of 20 mm dia alongwith all fittings and fixtures complete laid in trenches all as specified and directed.

S&F 25 mm PP-R Gate Valve cofiorming to IS 14846/2000,ISI Mark MS Spindle and iron wheel head with both ends flanged with new rubber gasket,bolts and nuts including dismantling of old u/s Gate valve fixed at any location of size 25 mmm dia all as specified and directed.

S&F 20 mm PP-R Gate Valve cofiorming to IS 14846/2000,ISI Mark MS Spindle and iron wheel head with both ends flanged with new rubber gasket,bolts and nuts including dismantling of old u/s Gate valve fixed at any location of size 20 mm dia all as specified and directed.

M&L for earthing complete with galvanised steel earth plate electrode 60 cm x 60 cm x 6 mm thick burried directly in ground (earth pit not less than 2.25 metres deep below normal ground level) vertically, with top edge of plate not less than 1.5 metre below normal ground level connected to galvanised earth lead wire 4 mm dia by means of bolts, nuts, check nuts and washers of galvanised iron or steel all as shown in electrical plate No 3 of MES Schedule Part-I connecting to earthing test. Testing on completion with and including necessary excavation and earth work in any type soil, earth lead connected to earth test point & to main switch board etc with & including adequate quantity of charcoal dust and common salt, test point, PCC (1:3:6) type C-1 (using 20mm graded BT stone aggregate) for earth pit with 40 x 40 x 6mm mild steel angle iron frame for cover, internal surface of concrete shall be given 10mm thick plaster in CM 1:4, pre cast RCC (1:2:4) type B-1 (using 20mm graded BT stone aggregate) 40mm thick cover, reinforced with 8mm dia deformed or TMT bars 3 Nos both way with 12 mm dia round bar handle, GI medium grade watering pipe 20 mm dia with funnel and wire mesh and 15mm dia GI medium grade earth lead protection pipe including provn of earth test point made of 50 x 5 mm MS Flat in 'D' shape 500 mm legth grouted in wall complete 01 x 6 mm multistrand PVC insulated copper conductor ( Green Colour) to be provided from test point to DB through 20 mm dia concealed non metallic conduit complete all as specified and directed as per MES Schedule Part I & II..

Removal of excavated material (soils) to a distance exc 1.5km but n.exc 5km where directed complete all as specified and directed.

M&L for PCC (1:4:8) type D2 using 40 mm graded stone aggregate as in concrete bed to drain pipes including packing under and hunching against the sides of pipes after they are laid and tested for 150 mm bore completeall as specified and directed.

M&L for PCC (1:4:8) type D-2 using 40mm graded stone aggregate as in foundation filling and mass concrete complete all as specified and directed.

M&L for brick work with kiln burnt bricks (old size) built in CM (1:4) using sub class 'B' bricks straight or curved on plan exceeding 6 meter mean radius complete all as specified and directed.

M&L for mild steel TMT bar 6 to 8 mm dia and over, cut to length, bent to shape required, including cranking, bending of required shape & sizeas directed fixing as rungs ectspirally for hooping for columns, hooking ends and binding with mild steel wire (annealed) not less than 0.9 mm dia, or securing with clips complete all as specified and directed.

Construction of Septic tanks including excavation, in any type of soil, foundation In PCC 1:2:4 type B-2, brick work in CM 1:4, RCC M20 (Nominal Mixed) (with and including reinforcement), Slab covers including RCC precast manhole cover having 6mm plate embedded all around/fibre reinforced cover with angle iron frame Vent pipe shaft and sludge chambers etc complete for25 users complete all as specified and shown in drawing No. CEBZ/TD/76/2011 Sheet 1/4 to 4/4.

Construction of Soakage wells including excavation in any type of soil, foundation in PCC 1:3:6, wells of honey combed and solid in M-25 (Nominal Mixed)Concrete type C2, including intercepting chamber, screen chamber Brick work in CM, RCC cover slab in M-20/ Brick Masonry/ filling with brick bats, complete of size 1.8 m in dia and 3.00m in deep (effective depth) all as specified and shown in drawing No.CEBZ/TD/78/2011 Sheet 1/2 & 2/2.

Construction of Soakage wells including excavation in any type of soil, foundation in PCC 1:3:6, wells of honey combed and solid in M-25 (Nominal Mixed)Concrete type C2, including intercepting chamber, screen chamber Brick work in CM, RCC cover slab in M-20/ Brick Masonry/ filling with brick bats, complete of size 1.2 m in dia and 3.00 m in deep (effective depth) all as specified and shown in drawing No.CEBZ/TD/78/2011 Sheet 1/2 & 2/2.

Removal excavated materials (soil) exceeding 250 meters but not 500 meters and deposting where directed at a level not exceeding 1.5 meters above the starting point, complete all as specified and directed.

Framed work such as grills, gratings, etc.. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe.290.Gde-E-165

M&L for Brick work with fly ash bricks, straight or curved on plan exceeding 6m mean radius, built in cement mortar 1:6 complete all as specified and directed

M&L for rendering 15 mm thick in Cement Plaster (1:4) on brick or concrete surface including finishing the surfaces even and smooth with out using extra cement complete all as specified and as directed

M&L for cement concrete type C2 1:3:6 (Using 40mm graded stone aggregate) as in surface channel and drain complete all as specified and directed.

M.S. ENGINEERS (BID ID -3444674)